Qlogic isp1040 with 2.4.21-rc1 (x86): driver won't load

DISCUSSION Zack Weinberg 1 participant 1 message May 4, 2003 SCSI

Share & tools

Zack Weinberg

author

2003-05-04 18:36 UTC #0 lore raw

I am trying to use a Qlogic isp1040 board with 2.4.21-rc1 (x86). lspci says:

00:09.0 SCSI storage controller: QLogic Corp. ISP1020 Fast-wide SCSI (rev 05)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort+ <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at b800 [size=256]
Region 1: Memory at e0000000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at <unassigned> [disabled] [size=64K]

I believe that qlogicisp.o is the correct driver for this board. When I try to load it, most of the time I get these error messages:

This is with RELOAD_FIRMWARE, DEBUG_ISP1020, and DEBUG_ISP1020_SETUP set to 1 in qlogicisp.c, and additionally with the "about firmware failure" printk augmented to print the error code. Code 4001 is INVALID_COMMAND according to the list of mailbox status codes, which seems decidedly odd.

Sometimes I get a different failure mode instead:

isp1020 : entering isp1020_detect()
PCI: Found IRQ 5 for device 00:09.0
isp1020 : entering isp1020_init()
qlogicisp : new isp1020 revision ID (5)
isp1020 : leaving isp1020_init()
isp1020 : entering isp1020_reset_hardware()
qlogicisp : mbox 0 0x0004
qlogicisp : mbox 1 0x4953
qlogicisp : mbox 2 0x5020
qlogicisp : mbox 3 0x2020
qlogicisp : mbox 4 0x0001
qlogicisp : mbox 5 0x0005
qlogicisp : loading risc ram
qlogicisp : verifying checksum
qlogicisp : executing firmware
qlogicisp : firmware major revision 2
qlogicisp : firmware minor revision 26
isp1020 : leaving isp1020_reset_hardware()
isp1020 : entering isp1020_set_defaults()
isp1020 : leaving isp1020_set_defaults()
isp1020 : entering isp1020_load_parameters()
isp1020 : leaving isp1020_load_parameters()
isp1020 : leaving isp1020_detect()
isp1020 : entering isp1020_info()
isp1020 : leaving isp1020_info()
scsi0 : QLogic ISP1020 SCSI on PCI bus 00 device 48 irq 5 MEM base 0xe091f000 isp1020 : entering isp1020_queuecommand()
qlogicisp : target = 0x00, lun = 0x00, cmd_len = 0x06
qlogicisp : command = 0x12 0x00 0x00 0x00 0xff 0x00
qlogicisp : request queue depth 62
isp1020 : leaving isp1020_queuecommand()
scsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 0 In quiry 00 00 00 ff 00
isp1020 : entering isp1020_abort()
isp1020 : leaving isp1020_abort()
scsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 0 In quiry 00 00 00 ff 00
isp1020 : entering isp1020_abort()
qlogicisp : scsi abort failure: 4005
SCSI host 0 abort (pid 0) timed out - resetting
SCSI bus is being reset for host 0 channel 0.
isp1020 : entering isp1020_reset()
qlogicisp : scsi bus reset failure: 4005
isp1020 : leaving isp1020_reset()
SCSI host 0 channel 0 reset (pid 0) timed out - trying harder
SCSI bus is being reset for host 0 channel 0.

[repeat until machine rebooted]

Code 4005 is COMMAND_ERROR. I am not sure what conditions trigger this second failure mode; it *might* be "there's a powered-up device other than the HBA on the SCSI bus."

Other information: The card is detected by the system BIOS, and the adapter BIOS configuration utility (Fast!somethingorother) works. When I've got the only other device on the bus (a DLT drive) turned on, a bus scan from the adapter BIOS sees it. However, the DOS-based flash update utility I downloaded from Qlogic's web site insists that there are no isp1xxx cards installed in the computer.

Any advice would be helpful. Please cc: me on replies.