ARM: mvebu: Add RN104 SATA LEDs driven via NXP PCA9554 I2C to GPIO muxer
PATCH 1/1 ARM: mvebu: Add RN104 SATA LEDs driven via NXP PCA9554 I2C to GPIO muxer
NETGEAR ReadyNAS 104 has a NXP PCA9554 I2C to GPIO chip. Among the 8 GPIO lines the chip makes available, four are used on the device to control the SATA LEDs (the four remaining ones are used for SATA disk presence). This patch adds DT entries for NXP PCA9554 and the four SATA GPIO LEDs.
---
Hi Jason,
This one depends on the patch (ARM: mvebu: Add Netgear ReadyNAS 104 board) which you pushed to Olof for inclusion in v3.13.
If you wonder why NETGEAR was short on GPIO lines from the Armada 370 SoC and had to add this, the answer is: the front Winstar WH1602 LCD consumes 7 lines.
Cheers,
a+
arch/arm/boot/dts/armada-370-netgear-rn104.dts | 31 ++++++++++++++++++++++++++ 1 file changed, 31 insertions(+)
arch/arm/boot/dts/armada-370-netgear-rn104.dts +31 -0
@@ -123,6 +123,13 @@ fan_startv = <1>; pwm_polarity = <0>; }; + + pca9554: pca9554 at 23 { + compatible = "nxp,pca9554"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x23>; + }; }; }; };
@@ -154,6 +161,30 @@ gpios = <&gpio2 0 1>; /* GPIO 64 Active Low */ linux,default-trigger = "keep"; }; + + sata1_led { + label = "rn104:blue:sata1"; + gpios = <&pca9554 0 1>; /* Active Low */ + default-state = "off"; + }; + + sata2_led { + label = "rn104:blue:sata2"; + gpios = <&pca9554 1 1>; /* Active Low */ + default-state = "off"; + }; + + sata3_led { + label = "rn104:blue:sata3"; + gpios = <&pca9554 2 1>; /* Active Low */ + default-state = "off"; + }; + + sata4_led { + label = "rn104:blue:sata4"; + gpios = <&pca9554 3 1>; /* Active Low */ + default-state = "off"; + }; }; gpio_keys {
Signature · 1 line
1.8.4.rc3
PATCH 1/1 ARM: mvebu: Add RN104 SATA LEDs driven via NXP PCA9554 I2C to GPIO muxer
Quoted 7 lines · Arnaud Ebalard
NETGEAR ReadyNAS 104 has a NXP PCA9554 I2C to GPIO chip. Among the 8 GPIO lines the chip makes available, four are used on the device to control the SATA LEDs (the four remaining ones are used for SATA disk presence). This patch adds DT entries for NXP PCA9554 and the four SATA GPIO LEDs.
Signed-off-by Arnaud Ebalard <[email protected]>---
[...]
Quoted 19 lines
arch/arm/boot/dts/armada-370-netgear-rn104.dts +7
-0@@ -123,6 +123,13 @@ fan_startv = <1>; pwm_polarity = <0>; }; + + pca9554: pca9554 at 23 { + compatible = "nxp,pca9554"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x23>; + }; }; }; };
arch/arm/boot/dts/armada-370-netgear-rn104.dts line 167
Quoted 7 lines
arch/arm/boot/dts/armada-370-netgear-rn104.dts +4
-0@@ -154,6 +161,30 @@ gpios = <&gpio2 0 1>; /* GPIO 64 Active Low */ linux,default-trigger = "keep"; }; + + sata1_led { + label = "rn104:blue:sata1"; + gpios = <&pca9554 0 1>; /* Active Low */
Same comment as for ReadyNAS 2120 patch:
#include <dt-bindings/gpio/gpio.h> and use GPIO_ACTIVE_HIGH/LOW.
Sebastian
Quoted 24 lines
arch/arm/boot/dts/armada-370-netgear-rn104.dts +20
-0+ default-state = "off"; + }; + + sata2_led { + label = "rn104:blue:sata2"; + gpios = <&pca9554 1 1>; /* Active Low */ + default-state = "off"; + }; + + sata3_led { + label = "rn104:blue:sata3"; + gpios = <&pca9554 2 1>; /* Active Low */ + default-state = "off"; + }; + + sata4_led { + label = "rn104:blue:sata4"; + gpios = <&pca9554 3 1>; /* Active Low */ + default-state = "off"; + }; }; gpio_keys {
PATCH 1/1 ARM: mvebu: Add RN104 SATA LEDs driven via NXP PCA9554 I2C to GPIO muxer
Hi,
Quoted 10 lines · Sebastian Hesselbarth
arch/arm/boot/dts/armada-370-netgear-rn104.dts line 167
Quoted 4 lines
arch/arm/boot/dts/armada-370-netgear-rn104.dts +4
-0+ + sata1_led { + label = "rn104:blue:sata1"; + gpios = <&pca9554 0 1>; /* Active Low */Same comment as for ReadyNAS 2120 patch:
#include <
dt-bindings/gpio/gpio.h> and use GPIO_ACTIVE_HIGH/LOW.Sebastian
Will fix that and resend tomorrow.
Cheers,
a+
PATCH 1/1 ARM: mvebu: Add RN104 SATA LEDs driven via NXP PCA9554 I2C to GPIO muxer
In reply to Sebastian HesselbarthHi Sebastian,
Quoted 11 lines · Sebastian Hesselbarth
arch/arm/boot/dts/armada-370-netgear-rn104.dts line 167
Quoted 8 lines
arch/arm/boot/dts/armada-370-netgear-rn104.dts +4
-0@@ -154,6 +161,30 @@ gpios = <&gpio2 0 1>; /* GPIO 64 Active Low */ linux,default-trigger = "keep"; }; + + sata1_led { + label = "rn104:blue:sata1"; + gpios = <&pca9554 0 1>; /* Active Low */Same comment as for ReadyNAS 2120 patch:
Quoted 1 line
#include <
dt-bindings/gpio/gpio.h> and use GPIO_ACTIVE_HIGH/LOW.
Unlike RN2120 .dts for which I was able to change all the high/low values for macros in a single move, if I do the changes here for this specific patch, the .dts file for the RN104 will contain both values and macros.
What about the following options?:
- send a preliminary patch to change all the values for macros in RN104 .dts file once -rc1 is here and then resubmit the PCA9554 patch with macros?
- have the patch applied as is and then convert the whole RN104 .dts w/ another patch.
Anyway, once RN2120 is accepted, I intend to spend some time doing some housekeeping on other readynas .dts file based on the comments you made recently (macros, reg, addressing, phy info, etc), and also some minor points (whitespaces).
Cheers,
a+
PATCH 1/1 ARM: mvebu: Add RN104 SATA LEDs driven via NXP PCA9554 I2C to GPIO muxer
Quoted 22 lines · Arnaud Ebalard
Hi Sebastian,
Quoted 11 lines · Sebastian Hesselbarth
arch/arm/boot/dts/armada-370-netgear-rn104.dts line 167
Quoted 8 lines
arch/arm/boot/dts/armada-370-netgear-rn104.dts +4
-0@@ -154,6 +161,30 @@ gpios = <&gpio2 0 1>; /* GPIO 64 Active Low */ linux,default-trigger = "keep"; }; + + sata1_led { + label = "rn104:blue:sata1"; + gpios = <&pca9554 0 1>; /* Active Low */Same comment as for ReadyNAS 2120 patch:
Quoted 1 line
#include <
dt-bindings/gpio/gpio.h> and use GPIO_ACTIVE_HIGH/LOW.Unlike RN2120 .dts for which I was able to change all the high/low values for macros in a single move, if I do the changes here for this specific patch, the .dts file for the RN104 will contain both values and macros.
Quoted 7 lines
What about the following options?:
- send a preliminary patch to change all the values for macros in RN104 .dts file once -rc1 is here and then resubmit the PCA9554 patch with macros?
- have the patch applied as is and then convert the whole RN104 .dts w/ another patch.
I'd say, respin this with gpio.h and go for a round of cleanup later.
Quoted 4 lines
Anyway, once RN2120 is accepted, I intend to spend some time doing some housekeeping on other readynas .dts file based on the comments you made recently (macros, reg, addressing, phy info, etc), and also some minor points (whitespaces).
Great!
Sebastian