Pending patches
Subsystems (3)
Robert Jarzmik
maintainerHi Sascha,
I have 2 sent patches which were somehow ... lost.
They have been sent on January the 26th, with the following subjects:
- [PATCH] arm/mach-pxa: add standard LCD panel GPIO settings
- [PATCH] arm/mach-pxa: add CCCR bits definitions
These are targeted at next branch. Could you consider pulling them ? I joined them in this mail to ease your search.
Cheers.
Signature · 1 line
Robert
From 2a3e758be559e34bffca8224b92e1d6f304ca5b8 Mon Sep 17 00:00:00 2001
From: Robert Jarzmik <[email protected]>
Date: Wed, 25 Jan 2012 10:12:28 +0100
Subject: [PATCH 1/2] arm/mach-pxa: add standard LCD panel GPIO settings
Add standard GPIO routings for LCD panels, taken from linux kernel.
--- arch/arm/mach-pxa/include/mach/mfp-pxa27x.h | 32 +++++++++++++++++++++++++++ 1 files changed, 32 insertions(+), 0 deletions(-)
arch/arm/mach-pxa/include/mach/mfp-pxa27x.h +32 -0
@@ -434,5 +434,37 @@#define GPIO112_nMSINS MFP_CFG_IN(GPIO112, AF2)#define GPIO32_MSSCLK MFP_CFG_OUT(GPIO32, AF1, DRIVE_LOW) +/* commonly used pin configurations */ +#define GPIOxx_LCD_16BPP \ + GPIO58_LCD_LDD_0, \ + GPIO59_LCD_LDD_1, \ + GPIO60_LCD_LDD_2, \ + GPIO61_LCD_LDD_3, \ + GPIO62_LCD_LDD_4, \ + GPIO63_LCD_LDD_5, \ + GPIO64_LCD_LDD_6, \ + GPIO65_LCD_LDD_7, \ + GPIO66_LCD_LDD_8, \ + GPIO67_LCD_LDD_9, \ + GPIO68_LCD_LDD_10, \ + GPIO69_LCD_LDD_11, \ + GPIO70_LCD_LDD_12, \ + GPIO71_LCD_LDD_13, \ + GPIO72_LCD_LDD_14, \ + GPIO73_LCD_LDD_15 + +#define GPIOxx_LCD_DSTN_16BPP \ + GPIOxx_LCD_16BPP, \ + GPIO74_LCD_FCLK, \ + GPIO75_LCD_LCLK, \ + GPIO76_LCD_PCLK + +#define GPIOxx_LCD_TFT_16BPP \ + GPIOxx_LCD_16BPP, \ + GPIO74_LCD_FCLK, \ + GPIO75_LCD_LCLK, \ + GPIO76_LCD_PCLK, \ + GPIO77_LCD_BIAS +extern int keypad_set_wake (unsigned int on);#endif /* __ASM_ARCH_MFP_PXA27X_H */
Signature · 1 line
1.7.5.4
From f6f80c5430c279eddaee39929e2182b6f4b6ac90 Mon Sep 17 00:00:00 2001
From: Robert Jarzmik <[email protected]>
Date: Wed, 25 Jan 2012 10:13:55 +0100
Subject: [PATCH 2/2] arm/mach-pxa: add CCCR bits definitions
Add CCCR bits definition for PXA SoC, so that the bootloader can setup a stable core clock frequency, which is not the initial reset clock, as required by Intel's PXA27x Processor family developer's guide, chapter 3.5.5, table 3.7 (clock frequencies).
--- arch/arm/mach-pxa/include/mach/pxa2xx-regs.h | 5 +++++ 1 files changed, 5 insertions(+), 0 deletions(-)
arch/arm/mach-pxa/include/mach/pxa2xx-regs.h +5 -0
@@ -222,6 +222,11 @@#define CCCR_N_MASK 0x0380/* Run Mode Frequency to Turbo Mode Frequency Multiplier */ #define CCCR_M_MASK 0x0060/* Memory Frequency to Run Mode Frequency Multiplier */ #define CCCR_L_MASK 0x001f/* Crystal Frequency to Memory Frequency Multiplier */ +#define CCCR_CPDIS (1 << 31) +#define CCCR_PPDIS (1 << 30) +#define CCCR_LCD26 (1 << 27) +#define CCCR_PLL_EARLY (1 << 26) +#define CCCR_A (1 << 25)#define CKEN_AC97CONF (1 << 31)/* AC97 Controller Configuration */ #define CKEN_CAMERA (1 << 24)/* Camera Interface Clock Enable */
Signature · 1 line
1.7.5.4
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
Hi Robert,
Quoted 9 lines · Robert Jarzmik
Hi Sascha,
I have 2 sent patches which were somehow ... lost.
They have been sent on January the 26th, with the following subjects:
- [PATCH] arm/mach-pxa: add standard LCD panel GPIO settings
- [PATCH] arm/mach-pxa: add CCCR bits definitionsThese are targeted at next branch. Could you consider pulling them ? I joined them in this mail to ease your search.
Yeah, I lost them. Applied now.
Thanks
Sascha
Signature · 9 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox