ARM: mvebu: Add RN104 SATA LEDs driven via NXP PCA9554 I2C to GPIO muxer
PATCH v2 1/1 ARM: mvebu: Add RN104 SATA LEDs driven via NXP PCA9554 I2C to GPIO muxer
NETGEAR ReadyNAS 104 has a NXP PCA9554 I2C to GPIO chip. Among the 8 GPIO lines the chip makes available, four are used on the device to control the SATA LEDs (the four remaining ones are used for SATA disk presence). This patch adds DT entries for NXP PCA9554 and the four SATA GPIO LEDs.
---
Hi Jason,
For some reason, I have forgotten this one in my drafts folder and noticed that just now. It goes on top of 45e8815f (ARM: mvebu: Add Netgear ReadyNAS 104 board) which is now sitting in Linus tree.
If you wonder why NETGEAR was short on GPIO lines from the Armada 370 SoC and had to add this, the answer is: the front Winstar WH1602 LCD consumes 7 lines.
Changes since v1:
Following comments from Sebastian:
- Changed values for macros for GPIO voltage level
Cheers,
a+
arch/arm/boot/dts/armada-370-netgear-rn104.dts | 32 ++++++++++++++++++++++++++ 1 file changed, 32 insertions(+)
arch/arm/boot/dts/armada-370-netgear-rn104.dts +32 -0
@@ -12,6 +12,7 @@ /dts-v1/; #include "armada-370.dtsi" +#include <dt-bindings/gpio/gpio.h> / { model = "NETGEAR ReadyNAS 104";
@@ -123,6 +124,13 @@ fan_startv = <1>; pwm_polarity = <0>; }; + + pca9554: pca9554 at 23 { + compatible = "nxp,pca9554"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x23>; + }; }; }; };
@@ -154,6 +162,30 @@ gpios = <&gpio2 0 1>; /* GPIO 64 Active Low */ linux,default-trigger = "keep"; }; + + sata1_led { + label = "rn104:blue:sata1"; + gpios = <&pca9554 0 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + sata2_led { + label = "rn104:blue:sata2"; + gpios = <&pca9554 1 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + sata3_led { + label = "rn104:blue:sata3"; + gpios = <&pca9554 2 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + sata4_led { + label = "rn104:blue:sata4"; + gpios = <&pca9554 3 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; }; gpio_keys {
Signature · 1 line
1.8.4.rc3
Jason Cooper
AppliedPATCH v2 1/1 ARM: mvebu: Add RN104 SATA LEDs driven via NXP PCA9554 I2C to GPIO muxer
Quoted 11 lines · Arnaud Ebalard
NETGEAR ReadyNAS 104 has a NXP PCA9554 I2C to GPIO chip. Among the 8 GPIO lines the chip makes available, four are used on the device to control the SATA LEDs (the four remaining ones are used for SATA disk presence). This patch adds DT entries for NXP PCA9554 and the four SATA GPIO LEDs.
Signed-off-by Arnaud Ebalard <[email protected]>---
arch/arm/boot/dts/armada-370-netgear-rn104.dts | 32 ++++++++++++++++++++++++++ 1 file changed, 32 insertions(+)
Applied to mvebu/dt
thx,
Jason.