Boot failure triggered by USB on rockpro64-rk3399 and pinebook-pro-rk3399
It seems rockpro64-rk3399 and pinebook-pro-rk3399 fail to boot when usb is started. It hangs indefinitely at:
## Flattened Device Tree blob at 01f00000
Booting using the fdt blob at 0x1f00000
I have observed this also using 2020.10 on rockpro64-rk3399, though on pinebook-pro-rk3399 usb does not work and so it basically avoids triggering the issue.
Setting CONFIG_USE_PREBOOT=n in the config works around the problem, though obviously by breaking usb keyboard support or booting from USB devices.
Related bugs in Debian and manjaro:
https://bugs.debian.org/973323
https://bugs.debian.org/980434
https://gitlab.manjaro.org/manjaro-arm/packages/core/uboot-rockpro64/-/issues/4
Boot log:
U-Boot 2021.01+dfsg-1 (Jan 17 2021 - 03:50:13 +0000)
SoC: Rockchip rk3399 Reset cause: POR Model: Pine64 RockPro64 v2.1 DRAM: 3.9 GiB PMIC: RK808 MMC: mmc at fe310000: 2, mmc at fe320000: 1, sdhci at fe330000: 0
Loading Environment from SPIFlash... SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment
In: serial Out: serial Err: serial Model: Pine64 RockPro64 v2.1 Net: eth0: ethernet at fe300000
starting USB...
Bus usb at fe380000: USB EHCI 1.00
Bus usb at fe3a0000: USB OHCI 1.0
Bus usb at fe3c0000: USB EHCI 1.00
Bus usb at fe3e0000: USB OHCI 1.0
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb at fe380000 for devices... 1 USB Device(s) found scanning bus usb at fe3a0000 for devices... 1 USB Device(s) found scanning bus usb at fe3c0000 for devices... 1 USB Device(s) found scanning bus usb at fe3e0000 for devices... 1 USB Device(s) found scanning bus dwc3 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
=> printenv preboot
preboot=usb start
=> usb reset
resetting USB...
Bus usb at fe380000: USB EHCI 1.00
Bus usb at fe3a0000: USB OHCI 1.0
Bus usb at fe3c0000: USB EHCI 1.00
Bus usb at fe3e0000: USB OHCI 1.0
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb at fe380000 for devices... 1 USB Device(s) found scanning bus usb at fe3a0000 for devices... 1 USB Device(s) found scanning bus usb at fe3c0000 for devices... 1 USB Device(s) found scanning bus usb at fe3e0000 for devices... 1 USB Device(s) found scanning bus dwc3 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
=> boot
Card did not respond to voltage select! : -110
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
144 bytes read in 5 ms (27.3 KiB/s)
1: Debian-Installer
Retrieving file: /initrd.gz
28995285 bytes read in 1287 ms (21.5 MiB/s)
Retrieving file: /vmlinuz
26922864 bytes read in 1195 ms (21.5 MiB/s)
Retrieving file: /dtbs/rockchip/rk3399-rockpro64.dtb 56849 bytes read in 13 ms (4.2 MiB/s)
Moving Image from 0x2080000 to 0x2200000, end=3c50000
## Flattened Device Tree blob at 01f00000
Booting using the fdt blob at 0x1f00000
live well,
vagrant
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 227 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20210120/d5898991/attachment.sig>
Hi Vagrant,
??? Do you know which version is the last version that works in this case?
??? The firmware is from eMMC and it's wired for USB to affect the boot
process.
Thanks,
- Kever
Quoted 97 lines · Vagrant Cascadian
It seems rockpro64-rk3399 and pinebook-pro-rk3399 fail to boot when usb is started. It hangs indefinitely at:
## Flattened Device Tree blob at
01f00000Booting using the fdt blob at 0x1f00000I have observed this also using 2020.10 on rockpro64-rk3399, though on pinebook-pro-rk3399 usb does not work and so it basically avoids triggering the issue.
Setting
CONFIG_USE_PREBOOT=nin the config works around the problem, though obviously by breaking usb keyboard support or booting from USB devices.Related bugs in Debian and manjaro:
https://bugs.debian.org/973323 https://bugs.debian.org/980434 https://gitlab.manjaro.org/manjaro-arm/packages/core/uboot-rockpro64/-/issues/4Boot log:
U-Boot 2021.01+dfsg-1 (Jan 17 2021 - 03:50:13 +0000)
SoC: Rockchip rk3399 Reset cause: POR Model: Pine64 RockPro64 v2.1 DRAM: 3.9 GiB PMIC: RK808 MMC: mmc at fe310000: 2, mmc at fe320000: 1, sdhci at fe330000: 0Loading Environment from SPIFlash... SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment
In: serial Out: serial Err: serial Model: Pine64 RockPro64 v2.1 Net: eth0: ethernet at fe300000starting USB...
Bus usb atfe380000: USB EHCI 1.00
Bus usb atfe3a0000: USB OHCI 1.0
Bus usb atfe3c0000: USB EHCI 1.00
Bus usb atfe3e0000: USB OHCI 1.0
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb atfe380000for devices... 1 USB Device(s) found scanning bus usb atfe3a0000for devices... 1 USB Device(s) found scanning bus usb atfe3c0000for devices... 1 USB Device(s) found scanning bus usb atfe3e0000for devices... 1 USB Device(s) found scanning bus dwc3 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
=> printenv preboot
preboot=usb start
=> usb reset
resetting USB...
Bus usb atfe380000: USB EHCI 1.00
Bus usb atfe3a0000: USB OHCI 1.0
Bus usb atfe3c0000: USB EHCI 1.00
Bus usb atfe3e0000: USB OHCI 1.0
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb atfe380000for devices... 1 USB Device(s) found scanning bus usb atfe3a0000for devices... 1 USB Device(s) found scanning bus usb atfe3c0000for devices... 1 USB Device(s) found scanning bus usb atfe3e0000for devices... 1 USB Device(s) found scanning bus dwc3 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
=> boot
Card did not respond to voltage select! : -110
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
144 bytes read in 5 ms (27.3 KiB/s)
1: Debian-Installer
Retrieving file: /initrd.gz
28995285 bytes read in 1287 ms (21.5 MiB/s)
Retrieving file: /vmlinuz
26922864 bytes read in 1195 ms (21.5 MiB/s)
Retrieving file: /dtbs/rockchip/rk3399-rockpro64.dtb
56849 bytes read in 13 ms (4.2 MiB/s)
Moving Image from0x2080000to0x2200000, end=3c50000
## Flattened Device Tree blob at01f00000Booting using the fdt blob at 0x1f00000live well,
vagrant
Quoted 6 lines · Vagrant Cascadian
It seems rockpro64-rk3399 and pinebook-pro-rk3399 fail to boot when usb is started. It hangs indefinitely at:
## Flattened Device Tree blob at
01f00000Booting using the fdt blob at 0x1f00000
Quoted 7 lines
I have observed this also using 2020.10 on rockpro64-rk3399, though on pinebook-pro-rk3399 usb does not work and so it basically avoids triggering the issue.
Setting
CONFIG_USE_PREBOOT=nin the config works around the problem, though obviously by breaking usb keyboard support or booting from USB devices.
This might be the same as [1] where running "usb stop" would hang, but disabling CONFIG_USB_OHCI_HCD and CONFIG_USB_OHCI_GENERIC gets the board to boot (still breaks the keyboard). Might help narrow things down.
[1] https://lists.denx.de/pipermail/u-boot/2020-November/432931.html
Quoted 1 line · Kever Yang
??? Do you know which version is the last version that works in this case?
The email I linked above has some versions they've tested, in case this is the same issue.
Jonathan Gray
Reviewed-by Kever YangU-Boot 2020.07 worked, broken on rockpro64 by
commit 3ae64582fb8ceead4fc464cd2055eb3eaef78ccc (refs/bisect/bad)
Author: Jagan Teki <[email protected]> Date: Mon Jul 20 14:53:09 2020 +0530
rockchip: rockpro64: Enable USB3.0 Host
Enable USB3.0 Host support for RockPro64 boards.
according to Kurt Miller who bisected this when the same problem was encountered booting OpenBSD. I don't have any rk3399 myself.
https://marc.info/?l=openbsd-ports&m=161005506031482&w=2
https://marc.info/?l=openbsd-ports&m=161012461223737&w=2
We ended up disabling CONFIG_USE_PREBOOT in rk3399 targets to fix booting via non-usb as well.
Quoted 112 lines · Kever Yang
Hi Vagrant,
??? Do you know which version is the last version that works in this case?
??? The firmware is from eMMC and it's wired for USB to affect the boot process.
Thanks,
- Kever
Quoted 97 lines · Vagrant Cascadian
It seems rockpro64-rk3399 and pinebook-pro-rk3399 fail to boot when usb is started. It hangs indefinitely at:
## Flattened Device Tree blob at
01f00000Booting using the fdt blob at 0x1f00000I have observed this also using 2020.10 on rockpro64-rk3399, though on pinebook-pro-rk3399 usb does not work and so it basically avoids triggering the issue.
Setting
CONFIG_USE_PREBOOT=nin the config works around the problem, though obviously by breaking usb keyboard support or booting from USB devices.Related bugs in Debian and manjaro:
https://bugs.debian.org/973323 https://bugs.debian.org/980434 https://gitlab.manjaro.org/manjaro-arm/packages/core/uboot-rockpro64/-/issues/4Boot log:
U-Boot 2021.01+dfsg-1 (Jan 17 2021 - 03:50:13 +0000)
SoC: Rockchip rk3399 Reset cause: POR Model: Pine64 RockPro64 v2.1 DRAM: 3.9 GiB PMIC: RK808 MMC: mmc at fe310000: 2, mmc at fe320000: 1, sdhci at fe330000: 0Loading Environment from SPIFlash... SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment
In: serial Out: serial Err: serial Model: Pine64 RockPro64 v2.1 Net: eth0: ethernet at fe300000starting USB...
Bus usb atfe380000: USB EHCI 1.00
Bus usb atfe3a0000: USB OHCI 1.0
Bus usb atfe3c0000: USB EHCI 1.00
Bus usb atfe3e0000: USB OHCI 1.0
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb atfe380000for devices... 1 USB Device(s) found scanning bus usb atfe3a0000for devices... 1 USB Device(s) found scanning bus usb atfe3c0000for devices... 1 USB Device(s) found scanning bus usb atfe3e0000for devices... 1 USB Device(s) found scanning bus dwc3 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
=> printenv preboot
preboot=usb start
=> usb reset
resetting USB...
Bus usb atfe380000: USB EHCI 1.00
Bus usb atfe3a0000: USB OHCI 1.0
Bus usb atfe3c0000: USB EHCI 1.00
Bus usb atfe3e0000: USB OHCI 1.0
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb atfe380000for devices... 1 USB Device(s) found scanning bus usb atfe3a0000for devices... 1 USB Device(s) found scanning bus usb atfe3c0000for devices... 1 USB Device(s) found scanning bus usb atfe3e0000for devices... 1 USB Device(s) found scanning bus dwc3 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
=> boot
Card did not respond to voltage select! : -110
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
144 bytes read in 5 ms (27.3 KiB/s)
1: Debian-Installer
Retrieving file: /initrd.gz
28995285 bytes read in 1287 ms (21.5 MiB/s)
Retrieving file: /vmlinuz
26922864 bytes read in 1195 ms (21.5 MiB/s)
Retrieving file: /dtbs/rockchip/rk3399-rockpro64.dtb
56849 bytes read in 13 ms (4.2 MiB/s)
Moving Image from0x2080000to0x2200000, end=3c50000
## Flattened Device Tree blob at01f00000Booting using the fdt blob at 0x1f00000live well,
vagrant