Skip to contentSkip to conversation

i had some problem in uboot1.1.1

U-Boot-Users 刘会田 2 participants 2 messages Nov 1, 2005

lore
Share & tools
lore

刘会田

author
#0 lore raw

i was a freshman in developing sbc8260 board.
i got a led_light program for testing boot ,and set some register right in
cpu_init_f. Why the uboot could not boot successed?
another questions:what purpose about env_init?
Thanks!
static int led_light(void)
{
int i,j;
char *k=0x21000000;
char ki[8]={0,4,2,6,1,5,3,7};
int l=0;
for(i=0;i<=7;i++)
{
for(j=1;j<100;j++)
{
l++;
}
*(k+ki[i])=0x80;
for(j=1;j<5000000;j++)
{
l--;
}
*(k+ki[i])=0x0;
return(0);
}
}

nit_fnc_t *init_sequence[] = {

#if defined(CONFIG_BOARD_EARLY_INIT_F)
board_early_init_f,
#endif

#if !defined(CONFIG_TQM866M)
get_clocks, /* get CPU and bus clocks (etc.) */ #if defined(CONFIG_TQM8xxL) && !defined(CONFIG_TQM866M) adjust_sdram_tbs_8xx,
#endif
init_timebase,
#endif
#ifdef CFG_ALLOC_DPRAM
#if !(defined(CONFIG_8260) || defined(CONFIG_MPC8560)) dpram_init,
#endif
#endif
#if defined(CONFIG_BOARD_POSTCLK_INIT) board_postclk_init,
#endif

led_light, //if i placed this program here, the led of board flashed.

env_init,

led_light, //if i placed this program here, the led of board didn't flash

#if defined(CONFIG_TQM866M)
get_clocks_866, /* get CPU and bus clocks according to the environment variable */
sdram_adjust_866, /* adjust sdram refresh rate according to the new clock */ init_timebase,
#endif
init_baudrate,
serial_init,
console_init_f,
display_options,
#if defined(CONFIG_8260)
prt_8260_rsr,
prt_8260_clks,
#endif /* CONFIG_8260 */
checkcpu,
#if defined(CONFIG_MPC5xxx)
prt_mpc5xxx_clks,
#endif /* CONFIG_MPC5xxx */
checkboard,
INIT_FUNC_WATCHDOG_INIT
#if defined(CONFIG_MISC_INIT_F)
misc_init_f,
#endif
INIT_FUNC_WATCHDOG_RESET
#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) init_func_i2c,
#endif
#if defined(CONFIG_DTT) /* Digital Thermometers and Thermostats */ dtt_init,
#endif
#ifdef CONFIG_POST
post_init_f,
#endif
INIT_FUNC_WATCHDOG_RESET
init_func_ram,
#if defined(CFG_DRAM_TEST)
testdram,
#endif /* CFG_DRAM_TEST */
INIT_FUNC_WATCHDOG_RESET

NULL, /* Terminate this list */
};
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.denx.de/pipermail/u-boot/attachments/20051101/5f2e1303/attachment.htm

#1 lore raw
Quoted 10 lines · In message <[email protected]> you wrote:

i was a freshman in developing sbc8260 board.
i got a led_light program for testing boot ,and set some register right in
cpu_init_f. Why the uboot could not boot successed?
another questions:what purpose about env_init?
Thanks!
static int led_light(void)
{
int i,j;
char *k=0x21000000;

What do you think is at physical address 0x21000000 ?

And why do you think the compiler will not optimize away your delay loops?

And why do you post code which is corrupted and unreadable?

Best regards,

Wolfgang Denk

Signature · 5 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
If you want strict real-time behavior, run in the real  time  schedu-
ling class.  But there are no seatbelts or airbags;  main(){for(;;);}
can hard hang your system.                          -- Bart Smaalders