Skip to contentSkip to conversation

STB0899 users, please verify results was Re: TechniSat SkyStar HD: Problems scaning and zaping

linux-dvb Simeon Simeonov 2 participants 2 messages Feb 29, 2008 Media (V4L/DVB)

lore
Share & tools
lore

Simeon Simeonov

author
#0 lore raw

I am using VP-1041 with the lnb21_attach changes to the ISEL and PCL bit settings. At the moemnt I have no clue why I am having this diseqc issue. I also checked the logs and I see from time to time diseqc_fifo_full messages but there is no correlation with the problem. For example I have not seen these messages for the last two days but sending more than 2 diseqc messages re-programs my rotor.

----- Original Message ----
From: Manu Abraham <[email protected]>
To: Simeon Simeonov <[email protected]>
Cc: [email protected]
Sent: Friday, February 29, 2008 3:20:39 PM
Subject: Re: [linux-dvb] STB0899 users, please verify results was Re: TechniSat SkyStar HD: Problems scaning and zaping

Quoted 4 lines · Simeon Simeonov

With 72e81184fb9f I get lock 5/10 times of the times and with a9ecd19a37c9 9/10 times. But with 72e81184fb9f I couldn't get neither my rotor nor diseqc switch to work as opposed to the tip where both work with some problems - sending more than 2 diseqc messages messes up my rotor.

You are using the Technisat HD2 or the VP-1041 ? if you are using the HD2, changeset 7280 alone adds support for the HD2, so in this case you will need to manually add support for the same.

In either of the case, i guess you have some sort of diseqc issue, but then have you tried with the LNBP21 attach change ?

Regards,
Manu

Quoted 22 lines

----- Original Message ----
From: Manu Abraham <[email protected]>
To: Simeon Simeonov <[email protected]>
Cc: [email protected]
Sent: Thursday, February 28, 2008 1:29:55 AM
Subject: Re: [linux-dvb] STB0899 users, please verify results was Re: TechniSat SkyStar HD: Problems scaning and zaping

Quoted 3 lines · Simeon Simeonov

I don't know if is the same but with the latest mantis tree I get 100% success. Reverting to changeset mantis-100d4b009238 (which I think corresponds to multiproto 7200) I do NOT any locks on the same transponder.

For the mantis tree, please test this changeset: 7275 72e81184fb9f as head
Please test how that looks in comparison to tip changeset 7282 a9ecd19a37c9

Regards,
Manu

Quoted 4 lines
      ____________________________________________________________________________________

Looking for last minute shopping deals?
Find them fast with Yahoo! Search. http://tools.search.yahoo.com/newsearch/category.php?category=shopping

      ____________________________________________________________________________________

Looking for last minute shopping deals?
Find them fast with Yahoo! Search. http://tools.search.yahoo.com/newsearch/category.php?category=shopping

_______________________________________________
linux-dvb mailing list
[email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

#1 lore raw
Quoted 4 lines · Simeon Simeonov

I am using VP-1041 with the lnb21_attach changes to the ISEL and PCL bit settings. At the moemnt I have no clue why I am having this diseqc issue. I also checked the logs and I see from time to time diseqc_fifo_full messages but there is no correlation with the problem.

Did you mean the "timed out !!" message from stb0899_wait_diseqc_fifo_empty() ?
(stb0899_drv.c, line #686, Trying to understand the problem that you are facing)

Regards,
Manu

_______________________________________________
linux-dvb mailing list
[email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb