Is there a way to use wireguard as a non-encrypted VPN?
I have some older routers that run OpenWRT just fine, but are a bit slow at Wireguard (3-5 MBytes/s for SMB transfers) and which are too slow for playing HD movies.
For these routers/uses I don't care about security, I just want a VPN to tunnel (thru Comcast, and other ISPs that block lots of ports.) If there was a way to use Wiireguard with encryption disabled, I'm pretty sure my performance would be closer to 20-50 MB/s which would be more than adequate.
Thanks.
Mike Farmwald
Quoted 12 lines · On Tue, Apr 14, 2020 at 10:30 AM <[email protected]> wrote:
I have some older routers that run OpenWRT just fine, but are a bit slow at Wireguard (3-5 MBytes/s for SMB transfers) and which are too slow for playing HD movies.
For these routers/uses I don't care about security, I just want a VPN to tunnel (thru Comcast, and other ISPs that block lots of ports.) If there was a way to use Wiireguard with encryption disabled, I'm pretty sure my performance would be closer to 20-50 MB/s which would be more than adequate.
Thanks.
Mike Farmwald
Hi Mike,
No, WireGuard does not and will never support your use case of disabling encryption.
If you are able to, buy a router that is powerful enough to do WireGuard at your preferred throughput. Otherwise you would need to use other encapsulation methods. OpenVPN with hardware AES acceleration might work (if your routers support that). However OpenVPN lives in userspace so it needs to do a memory copy from kernel to userspace for each packet. I'm not sure how the performance will work out in practice.
If you look at other methods you might want to consider the state of its maintenance. PPTP code is likely to be very old and unmaintained for instance. Your router might very well end up hacked.
Cheers,
Fredrik Stromberg
Quoted 11 lines · On Sat, 11 Apr 2020 12:13:36 -0700 <[email protected]> wrote:
I have some older routers that run OpenWRT just fine, but are a bit slow at Wireguard (3-5 MBytes/s for SMB transfers) and which are too slow for playing HD movies.
For these routers/uses I don't care about security, I just want a VPN to tunnel (thru Comcast, and other ISPs that block lots of ports.) If there was a way to use Wiireguard with encryption disabled, I'm pretty sure my performance would be closer to 20-50 MB/s which would be more than adequate.
Thanks.
Mike Farmwald
If you're actually just looking for an unencrypted tunnel, there is some standardized stuff like GRE[1] or IP in IP[2] out there.
The Linux Kernel supports both of those natively and it looks to me like OpenWRT should be able to configure at least one of them through its interface.
1: https://en.wikipedia.org/wiki/Generic_Routing_Encapsulation
2: https://en.wikipedia.org/wiki/IP_in_IP
Quoted 15 lines · On Tue, 14 Apr 2020 17:02:41 +0200 ajs124 <[email protected]> wrote:
Quoted 11 lines · On Sat, 11 Apr 2020 12:13:36 -0700 <[email protected]> wrote:
I have some older routers that run OpenWRT just fine, but are a bit slow at Wireguard (3-5 MBytes/s for SMB transfers) and which are too slow for playing HD movies.
For these routers/uses I don't care about security, I just want a VPN to tunnel (thru Comcast, and other ISPs that block lots of ports.) If there was a way to use Wiireguard with encryption disabled, I'm pretty sure my performance would be closer to 20-50 MB/s which would be more than adequate.
Thanks.
Mike Farmwald
Quoted 6 lines
If you're actually just looking for an unencrypted tunnel, there is some standardized stuff like GRE[1] or IP in IP[2] out there.
The Linux Kernel supports both of those natively and it looks to me like OpenWRT should be able to configure at least one of them through its interface.
1: https://en.wikipedia.org/wiki/Generic_Routing_Encapsulation
2: https://en.wikipedia.org/wiki/IP_in_IP
Those both require dedicated IP on both ends of the connection, which is not always the case on residential ISPs' IPv4 now.
I'd suggest to check out L2TP instead, which doesn't, and can be used without encryption too, that one can work.
Or PPTP as mentioned, but it's more complex (separate signaling and data protocols) for no good reason and has more issues traversing NATs/firewalls.
Signature · 2 lines
With respect, Roman
Quoted 13 lines · On 12/4/20 4:43 am, [email protected] wrote:
I have some older routers that run OpenWRT just fine, but are a bit slow at Wireguard (3-5 MBytes/s for SMB transfers) and which are too slow for playing HD movies.
For these routers/uses I don't care about security, I just want a VPN to tunnel (thru Comcast, and other ISPs that block lots of ports.) If there was a way to use Wiireguard�with encryption disabled, I'm pretty sure my performance would be closer to 20-50 MB/s which would be more than adequate.
Thanks.
Mike Farmwald
I suggest that your use a GRE tunnel connection.
Mike