Changing PCI board's IRQ
Hello,
One computer that I administer have a IRQ conflict between a sound card and a ethernet card. Both share the IRQ 11.
I don't have physical access to the computer, so I tried to change the IRQ using the 'setpci' command.
# setpci -v -s 0:7.5 INTERRUPT_LINE=08 00:07.5:3c 08 #
But, after that, when I did a
# lspci -vv -s 0:7.5
00:07.5 Multimedia audio controller: VIA Technologies, Inc. AC97 Audio
Controller (rev 50)
Subsystem: Biostar Microtech Int'l Corp: Unknown device 0032
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 11
Region 0: I/O ports at dc00 [size=256]
Region 1: I/O ports at e000 [size=4]
Region 2: I/O ports at e400 [size=4]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-After some experience (like rebooting... arg!) i tried:
# lspci -vv -H1 -s 0:7.5
<cut>
Interrupt: pin C routed to IRQ 8
Region 0: I/O ports at dc00
<cut>So, it seems that either I cannot change the Interrupt line number throught software (and the -H1 is tricky) or the /proc/pci (and /proc/bus/pci) is not getting updated.
Is that a problem or am I missing the point?
P.S.: Please Reply direct to me (or send me a copy) because I can not "afford" the traffic of linux-kernel. :)
Signature · 10 lines
Raphael Derosso Pereira - DephiNit
*-=-*-=--=-*-=-*-=--=*=-*
/ [email protected] /
*-=-*-=--=-*-=-*-=--=*=-*
-=*=--=*=--=*=--=*=--=*=--=*=--=*=-
| Debian GNU/Linux Addicted User |
| Use it, Abuse it. It's Free!!! |
-=*=--=*=--=*=--=*=--=*=--=*=--=*=-Quoted 10 lines · Raphael Derosso Pereira - DephiNit
Hello,
One computer that I administer have a IRQ conflict between a sound card and a ethernet card. Both share the IRQ 11.
I don't have physical access to the computer, so I tried to change the IRQ using the 'setpci' command.# setpci -v -s 0:7.5 INTERRUPT_LINE=08 00:07.5:3c 08 #
well, this is obviously the wrong solution. If both boards are PCI boards, they can easily share the IRQ between them.
If one of the boards is an ISA device, configure your BIOS correctly (i.e. telling it that IRQ11 is used by a non-pnp legacy ISA device).
Quoted 3 lines
So, it seems that either I cannot change the Interrupt line number throught software (and the -H1 is tricky) or the
/proc/pci(and/proc/bus/pci) is not getting updated.
You can't just change the IRQ in pci config space. You will not change the real IRQ mapping but just somthing the BIOS wrote there during initialization.
Quoted 2 lines
Is that a problem or am I missing the point?
Signature · 5 lines
Live long and prosper - Harald Welte / [email protected] http://www.gnumonks.org/ ============================================================================ GCS/E/IT d- s-: a-- C+++ UL++++$ P+++ L++++$ E--- W- N++ o? K- w--- O- M+ V-- PS++ PE-- Y++ PGP++ t+ 5-- !X !R tv-- b+++ !DI !D G+ e* h--- r++ y+(*)