Skip to contentSkip to conversation

Alsa-devel digest, Vol 1 #810 - 3 msgs

DISCUSSION Bob McElrath 5 participants 9 messages Oct 29, 2002 – Nov 11, 2003 1 message not in the archive

lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): [email protected]

#1 lore raw
Quoted 31 lines · [email protected]…

Date: Tue, 29 Oct 2002 08:55:06 +0100
From: Benny Sjostrand <[email protected]>
To: [email protected]
Subject: [Alsa-devel] [PATCH] cs46xx, independant rear PCM channel, IEC958 PCM channel

This is a multi-part message in MIME format. --------------090804060704000507060108
Content-Type: text/plain; charset=us-ascii; format=flowed
Content-Transfer-Encoding: 7bit

Hi!

First, this stuff is still very experimental, it should work very well with a
Game Theater XP course that's card I've got and the only cs46xx sound card I can
test with.

I've got some reports that stuffs dont seems to work very well with the Santa Cruz card, course for some unknown reason the driver dont manage to raise GPIO 7 and 9 on the secondary codec that enables the rear output, you probably will see the message "cs46xx_setup_eapd_slot() Failure to write the GPIO pins for slot 12. " and that will probably freeze you computer for a while too.

In this patch, for the Santa Cruz the amplifier and the GPIO's are setup on init, then not touched anymore, like it's done for the Hercules XP card with hope and a little of luck maybe that works better.

Quoted 8 lines

Finally, this patch contains the following changes:
- Rear PCM channel
- IEC958 PCM channel, in hope that I'm close to get raw AC3 working soon
- Turn on Amplifier and setup EGPIO for Santa Cruz card on init
- Cleanup's in voyectra_setup_eapd_slot(...) (hope it's not broken ...)

PS. If you have time to help testing this patch, dont forget to turn on all debuging stuff, that always helps to find bugs ...

With a GTXP on an alpha. ;)

I managed to stall the codec by playing with the IEC958. I turned the IEC958 input all the way down, unmuted it, then unmuted the IEC958 output. I was playing an mp3 at the time, and the mp3 stopped and the codec just puts out a constant ~8khz tone. This is repeatable.

The 3D Depth seems to work now, sounds great. I don't think it worked before... ;)

Playing 2 pcm inputs at the same time seems to work great.

Recording still seems to not work. I still get about a 1Hz ticking in the right channel when recording (no matter what the mixer settings).

I don't see a debug setting on the modules snd-cs46xx or snd -- is this a compile time setting? Anyway, let me know if you want me to send you some debug output.

What is the easy way to test playing to the rear pcm channel?

Cheers,
-- Bob

Bob McElrath
Univ. of Wisconsin at Madison, Department of Physics

"The surest way to corrupt a youth is to instruct him to hold in higher esteem those who think alike than those who think differently."
-- Nietzsche

#2 lore raw
Quoted 2 lines · On 2002.10.29 08:36 Bob McElrath wrote:

I don't see a debug setting on the modules snd-cs46xx or snd -- is this a compile time setting?

Yes, you set this when you configure the package. Use the configure
option "--with-debug=detect" for the most verbose debugging output.

Quoted 1 line

What is the easy way to test playing to the rear pcm channel?

The easy way: aplay -Dhw:0,1 test.wav

Just don't forget to unmute and raise the volume for the rear-output.
Also, if you wish to output directly to SPDIF, use: "aplay -Dhw:0,2".

Thanks for testing. ;-)

HTH,
-- Peter Heatwole
"Murphy was just a well known pessimist."

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf

#3 lore raw
Quoted 11 lines · Peter Heatwole [[email protected]] wrote:
Quoted 2 lines · On 2002.10.29 08:36 Bob McElrath wrote:

I don't see a debug setting on the modules snd-cs46xx or snd -- is this a compile time setting?

Yes, you set this when you configure the package. Use the configure
option "--with-debug=detect" for the most verbose debugging output.

Quoted 1 line

What is the easy way to test playing to the rear pcm channel?

The easy way: aplay -Dhw:0,1 test.wav

Seems to work well. The relevant mixer settings are PCM1 and Surround1 (both of which must be turned up and unmuted. However it doesn't seem to deal well with odd rates:

(0)<mcelrath@draal:/home/mcelrath> aplay -Dhw:0,1 /usr/share/sounds/zipper.wav Playing WAVE '/usr/share/sounds/zipper.wav' : Unsigned 8 bit, Rate 11025 Hz, Mono
aplay: pcm_write:968: write error: Input/output error

Quoted 2 lines

Just don't forget to unmute and raise the volume for the rear-output.
Also, if you wish to output directly to SPDIF, use: "aplay -Dhw:0,2".

Unfortunately I don't have any hardware which can deal with SPDIF (except my Marvel TV card which only has an output).

Quoted 1 line

Thanks for testing. ;-)

No prob.

Quoted 1 line

HTH,

Have The Ham?

Cheers,
-- Bob

Bob McElrath ([email protected]) Univ. of Wisconsin at Madison, Department of Physics

"The surest way to corrupt a youth is to instruct him to hold in higher esteem those who think alike than those who think differently."
-- Nietzsche

#4 lore raw
Quoted 10 lines

Seems to work well. The relevant mixer settings are PCM1 and Surround1 (both of which must be turned up and unmuted. However it doesn't seem to deal well with odd rates:

(0)<mcelrath@draal:/home/mcelrath> aplay -Dhw:0,1 /usr/share/sounds/zipper.wav Playing WAVE '/usr/share/sounds/zipper.wav' : Unsigned 8 bit, Rate 11025 Hz, Mono
aplay: pcm_write:968: write error: Input/output error

Hm.,, just weird, does it work OK with the fron channel (hw:0,0) ???

What do get on dmesg output ???

/Benny

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf

#5 lore raw
Quoted 12 lines · Benny Sjostrand [[email protected]] wrote:
Quoted 11 lines

Seems to work well. The relevant mixer settings are PCM1 and Surround1 (both of which must be turned up and unmuted. However it doesn't seem to deal well with odd rates:

(0)<mcelrath@draal:/home/mcelrath> aplay -Dhw:0,1 /usr/share/sounds/zipper.wav Playing WAVE '/usr/share/sounds/zipper.wav' :
Unsigned 8 bit, Rate 11025 Hz, Mono
aplay: pcm_write:968: write error: Input/output error

Quoted 3 lines

Hm.,, just weird, does it work OK with the fron channel (hw:0,0) ???

What do get on dmesg output ???

The relevant stuff is:

Oct 29 23:52:11 draal kernel: ALSA dsp_spos_scb_lib.c:1188: dsp_spos: creating SRC "SrcTask_SCB0"
Oct 29 23:52:11 draal kernel: ALSA dsp_spos_scb_lib.c:295: dsp_spos: creating SCB <SrcTask_SCB0>
Oct 29 23:52:11 draal kernel: ALSA dsp_spos_scb_lib.c:1355: dsp_spos: setting SRC rate to 44100
Oct 29 23:52:11 draal kernel: ALSA dsp_spos_scb_lib.c:1211: dsp_spos: creating PCM "PCMReader_SCB0" (1)
Oct 29 23:52:11 draal kernel: ALSA dsp_spos_scb_lib.c:295: dsp_spos: creating SCB <PCMReader_SCB0>
Oct 29 23:52:11 draal kernel: ALSA dsp_spos_scb_lib.c:1355: dsp_spos: setting SRC rate to 11025
Oct 29 23:52:21 draal kernel: ALSA dsp_spos_scb_lib.c:231: cs46xx_dsp_proc_free_scb_desc: freeing PCMReader_SCB0
Oct 29 23:52:21 draal kernel: ALSA dsp_spos_scb_lib.c:231: cs46xx_dsp_proc_free_scb_desc: freeing SrcTask_SCB0

Why does it set 44.1kHz first and then set it to 11kHz?

I hear the first piece (frag?) of the sample played repeatedly, as if it were not servicing interrupts...

Messages for the 2nd pcm channel are identical if you s/(1)/(2)/ above.

As to the recording problem, I have tried all the options I can think of, all the mixer settings and possible inputs, and I still get ticking. NO messages are written to the logs during the record.
arecord -d 2 -f cd blah.wav
I have placed this file here: http://mcelrath.org/blah.wav.bz2

Cheers,
-- Bob

Bob McElrath
Univ. of Wisconsin at Madison, Department of Physics

"The surest way to corrupt a youth is to instruct him to hold in higher esteem those who think alike than those who think differently."
-- Nietzsche

#6 lore raw

request

Can anyone send me the alsa design document. I am interested in developing a ALSA driver.

Thank you,
Shiva

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf

#7 lore raw
In reply to Bob McElrath
Quoted 5 lines

With a GTXP on an alpha. ;)

Cool! stupid question from me, which endianess does the Alpha architecture have ?? well, I believe the cs46xx is never tested on Big-Endian architecture

Quoted 6 lines

I managed to stall the codec by playing with the IEC958. I turned the IEC958 input all the way down, unmuted it, then unmuted the IEC958 output. I was playing an mp3 at the time, and the mp3 stopped and the codec just puts out a constant ~8khz tone. This is repeatable.

A old bug that I supposed was fixed, but apparentily it's not, probably course I've never tested to play with SPDIF in and SPDIF out control at the same time. Hopefully I'll find a way to get around it ....

Just to confirm; if you only play with SPDIF input mixer control, leaving the SPDIF output unmuted it dont happen right ?

Quoted 4 lines

Recording still seems to not work. I still get about a 1Hz ticking in the right channel when recording (no matter what the mixer settings).

Recording should work fine, did you have the DAC capture SPIDF input "on" ?? then it could be SPDIF input related ...

/Benny

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf

#8 lore raw
Quoted 6 lines · Benny Sjostrand [[email protected]] wrote:
Quoted 6 lines

Seems to work well. The relevant mixer settings are PCM1 and Surround1 (both of which must be turned up and unmuted. However it doesn't seem to deal well with odd rates:

Quoted 8 lines
Quoted 6 lines

(0)<mcelrath@draal:/home/mcelrath> aplay -Dhw:0,1 /usr/share/sounds/zipper.wav Playing WAVE '/usr/share/sounds/zipper.wav' :
Unsigned 8 bit, Rate 11025 Hz, Mono
aplay: pcm_write:968: write error: Input/output error

Hm.,, just weird, does it work OK with the fron channel (hw:0,0) ???

Exact same results for hw:0,0. (i.e. it doesn't work)

Quoted 1 line

What do get on dmesg output ???

I still need to recompile with debug. I will send debug messages later.

Quoted 6 lines · Benny Sjostrand [[email protected]] wrote:
Quoted 3 lines

With a GTXP on an alpha. ;)

Cool! stupid question from me, which endianess does the Alpha architecture have ??
well, I believe the cs46xx is never tested on Big-Endian architecture

Alpha is little endian. (The processor itself can be either, but linux/alpha uses little endian)

Quoted 5 lines
Quoted 5 lines

I managed to stall the codec by playing with the IEC958. I turned the IEC958 input all the way down, unmuted it, then unmuted the IEC958 output. I was playing an mp3 at the time, and the mp3 stopped and the codec just puts out a constant ~8khz tone. This is repeatable.

Quoted 7 lines

A old bug that I supposed was fixed, but apparentily it's not, probably course
I've never tested to play with SPDIF in and SPDIF out control at the same time. Hopefully I'll find a way to get around it ....

Just to confirm; if you only play with SPDIF input mixer control, leaving the SPDIF output unmuted it dont happen right ?

Yes.

BTW I recommend renaming the IEC958 to "SPDIF" or "Digital In/Out" since nobody knows what an IEC958 is...

Quoted 6 lines
Quoted 3 lines

Recording still seems to not work. I still get about a 1Hz ticking in the right channel when recording (no matter what the mixer settings).

Recording should work fine, did you have the DAC capture SPIDF input "on" ?? then
it could be SPDIF input related ...

I cannot record anything at all, from any input (I haven't tried from SPDIF -- I don't have a reliable SPDIF source anyway) I get the 1Hz ticking.

Cheers,
-- Bob

Bob McElrath ([email protected]) Univ. of Wisconsin at Madison, Department of Physics

"The surest way to corrupt a youth is to instruct him to hold in higher esteem those who think alike than those who think differently."
-- Nietzsche

#9 lore raw

recording problems with snd-cs46xx (was: Re: Re: Alsa-devel digest, Vol 1 #810 - 3 msgs)

Hi,

this issue is over a year old, but in case someone stumbles on to the same problem. The solution is already documented at

http://alsa.opensrc.org/index.php?page=cs46xx

... but it took me a while to find it. :)

Quoted 3 lines · Bob McElrath
Quoted 1 line
Quoted 1 line

Recording still seems to not work. I still get about a 1Hz ticking in

I cannot record anything at all, from any input (I haven't tried from SPDIF -- I don't have a reliable SPDIF source anyway) I get the 1Hz

I had this very same problem with alsa-driver-0.9.8. The problem turned out to be that I had not selected 'ADC' as a capture source in alsamixer. So you need to select all three: 'ADC', 'Mic' and 'Capture' for the recording to work properly.

PS Tested with IBM Thinkpad models T20 and T21.

Signature · 10 lines
 http://www.eca.cx
 Audio software for Linux!



-------------------------------------------------------
This SF.Net email sponsored by: ApacheCon 2003,
16-19 November in Las Vegas. Learn firsthand the latest
developments in Apache, PHP, Perl, XML, Java, MySQL,
WebDAV, and more! http://www.apachecon.com/