CVS: alsa-lib/test iecbits.c,NONE,1.1 iecset.c,NONE,1.1 .cvsignore,1.11,1.12 Makefile.am,1.24,1.25
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 11 lines · Takashi Iwai
Update of /cvsroot/alsa/alsa-lib/test
In directory sc8-pr-cvs1:/tmp/cvs-serv8451Modified Files:
.cvsignore Makefile.am
Added Files:
iecbits.ciecset.c
Log Message:
added iecset program (this could be to alsa-utils after more enhancements).
This could be useful for a number of reasons.
One reason it might help for is this.
1) Application outputing to the "front" device outputs sound to the spdif with PCM iec mode set.
2) Application finishes, leaving PCM iec mode set.
3) New application outputs AC3 stream with NON-AUDIO iec mode set.
4) Application finishes, leaving PCM iec mode set.
5) New application outputs AC3 stream with NON-AUDIO iec mode set.
6) Application gets killed with "kill -9 PID" leaving NON-AUDIO iec mode set.
7) Application outputing to the "front" device outputs sound, but the spdif is left in NON-AUDIO iec mode, so no sound comes out of the spdif.
From then onwards all application outputting sound will default to NON-AUDIO bit being set, when the sensible assumption would be to set PCM mode as default, and only set NON-AUDIO mode when using a device name like "iec958:AES0=0x6,AES1=0x82,AES2=0x0,AES3=0x2"
So my question is, can iecbits.c code be used to set the default iec mode back to PCM, if it has accidentally been fixed on NON-AUDIO due to the kill -9 ?
Cheers
James
-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf
At Tue, 30 Sep 2003 18:20:24 +0100,
Quoted 30 lines · James Courtier-Dutton
Quoted 11 lines · Takashi Iwai
Update of /cvsroot/alsa/alsa-lib/test
In directory sc8-pr-cvs1:/tmp/cvs-serv8451Modified Files:
.cvsignore Makefile.am
Added Files:
iecbits.ciecset.c
Log Message:
added iecset program (this could be to alsa-utils after more enhancements).This could be useful for a number of reasons.
One reason it might help for is this.
1) Application outputing to the "front" device outputs sound to the spdif with PCM iec mode set.
2) Application finishes, leaving PCM iec mode set.
3) New application outputs AC3 stream with NON-AUDIO iec mode set.
4) Application finishes, leaving PCM iec mode set.
5) New application outputs AC3 stream with NON-AUDIO iec mode set.
6) Application gets killed with "kill -9 PID" leaving NON-AUDIO iec mode set.
7) Application outputing to the "front" device outputs sound, but the spdif is left in NON-AUDIO iec mode, so no sound comes out of the spdif. From then onwards all application outputting sound will default to
NON-AUDIO bit being set, when the sensible assumption would be to set PCM mode as default, and only set NON-AUDIO mode when using a device name like "iec958:AES0=0x6,AES1=0x82,AES2=0x0,AES3=0x2"
Quoted 3 lines
So my question is, can
iecbits.ccode be used to set the default iec mode back to PCM, if it has accidentally been fixed on NON-AUDIO due to the kill -9 ?
yes, just run:
% iecset audio yes
for changing the sample rate to 44.1kHz and switch to professional mode with non-audio mode, run it like:
% iecset prof yes rate 44100 audio no
the program will dump the current status (after changing values if any given), too, like below:
% iecset Mode: consumer Data: audio Rate: 48000 Hz Copyright: permitted Emphasis: none Category: mixer Original: original Clock: 1000 ppm
with -x option, it will print AES arguments for convenience, instead of human readable information:
% iecset -x AES0=0x04,AES1=0x92,AES2=0x10,AES3=0x02
as mentioned above, it's put just for tests, so far.
if there is enough demand, it should be on alsa-utils, of couse :)
Takashi
-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf
At Tue, 30 Sep 2003 19:33:58 +0200,
Quoted 3 lines · I wrote:
as mentioned above, it's put just for tests, so far.
if there is enough demand, it should be on alsa-utils, of couse :)
ok, now it's moved to alsa-utils, so that everyone can use this small guy. it will appear in alsa-utils tarball in the next release.
Takashi
-------------------------------------------------------
This SF.net email is sponsored by: The SF.net Donation Program. Do you like what SourceForge.net is doing for the Open Source Community? Make a contribution, and help us add new features and functionality. Click here: http://sourceforge.net/donate/