Mistral AM37x (with AM3715) devel board networking broken
sanjeev,
Thanks much for the help.
Quoted 2 lines
[sp] On first looks I would suspect the u-boot. 2009.11 seems to be quite old.
Can you try using version 2010.09?
I had tried 2010.09 on this board originally but found that it
wasn't stable, it was almost like the SDRAM wasn't set up correctly. I'd get random panic's on bad pointers in Linux. But I tried it anyway on this new kernel and it does set up the networking about 1 in 5 boots. Here is a boot where it set up the network
http://www.efn.org/~rick/pub/boot4.log, it still has the warnings though.
Please check my setup of u-boot, here is what I did:
wget ftp://ftp.denx.de/pub/u-boot/u-boot-2010.09.tar.bz2 tar jxf u-boot-2010.09.tar.bz2
cd u-boot-2010.09; make omap3_evm_config; make
Is this the correct config (omap3_evm_config) to use for this board?
Maybe you could tell me what exact u-boot and kernel you'd recommend and the steps to get them for this board.
Thanks,
Rick
Quoted 15 lines
-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of Rick Bronson
Sent: Sunday, November 07, 2010 9:15 PM
To: [email protected]; [email protected]
Subject: RE: Mistral AM37x (with AM3715) devel board networking brokensanjeev,
Thanks much for the help.
Quoted 1 line
[sp] On first looks I would suspect the u-boot. 2009.11
seems to be quite old.
Quoted 1 line
Can you try using version 2010.09?
Quoted 7 lines
I had tried 2010.09 on this board originally but found that it
wasn't stable, it was almost like the SDRAM wasn't set up correctly. I'd get random panic's on bad pointers in Linux. But I tried it anyway on this new kernel and it does set up the networking about 1 in 5 boots. Here is a boot where it set up the network
http://www.efn.org/~rick/pub/boot4.log, it still has the warnings though.
[sp] If you noticed, earlier u-boot version was identifying your board as:
U-Boot 2009.11 (Oct 30 2010 - 13:14:45)
OMAP34xx/35xx-GP ES1.0, CPU-OPP2 L3-165MHz
OMAP3 EVM board + LPDDR/NAND
Now,
U-Boot 2010.09 (Nov 07 2010 - 07:08:44)
OMAP3630/3730-GP ES1.0, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz OMAP3 EVM board + LPDDR/NAND
That's ai improvement.
However, in your log, I see folloing:
[ 0.000000] Total of 96 interrupts on 1 active controller [ 0.000000] Could not get gpios_ick [ 0.000000] Could not get gpios_fck
Looks like there are some changes - either in your Kconfig or elsewhere in the code that "get" gpio clocks is failing.
The SMSC chip is "virtually" non-existent for the Linux kernel here onwards.
My kernel version is "Linux-2.6.36-rc8-09072-g661df74-"
I have not yet looked at, but there is possible "break" on on mainline for EVM due to gpio related changes. You could be experiencing this break...
~sanjeev
Quoted 20 lines
Please check my setup of u-boot, here is what I did:
wget ftp://ftp.denx.de/pub/u-boot/u-boot-2010.09.tar.bz2 tar jxf u-boot-2010.09.tar.bz2
cd u-boot-2010.09; makeomap3_evm_config; makeIs this the correct config (
omap3_evm_config) to use for this board?
Maybe you could tell me what exact u-boot and kernel you'd recommend and the steps to get them for this board.Thanks,
Rick
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Quoted 69 lines
-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of Premi, Sanjeev
Sent: Monday, November 08, 2010 5:37 PM
To: Rick Bronson; [email protected]; [email protected]
Subject: RE: Mistral AM37x (with AM3715) devel board networking brokenQuoted 6 lines
-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of Rick Bronson
Sent: Sunday, November 07, 2010 9:15 PM
To: [email protected]; [email protected]
Subject: RE: Mistral AM37x (with AM3715) devel boardnetworking broken
Quoted 5 lines
sanjeev,
Thanks much for the help.
Quoted 8 lines
Quoted 1 line
[sp] On first looks I would suspect the u-boot. 2009.11
seems to be quite old.
Quoted 1 line
Can you try using version 2010.09?
I had tried 2010.09 on this board originally but found that it
wasn't stable, it was almost like the SDRAM wasn't set up correctly. I'd get random panic's on bad pointers in Linux. But I tried it anyway on this new kernel and it does set up the networkingabout 1 in
Quoted 3 lines
5 boots. Here is a boot where it set up the network
http://www.efn.org/~rick/pub/boot4.log, it still has the warnings though.[sp] If you noticed, earlier u-boot version was identifying your board as:
U-Boot 2009.11 (Oct 30 2010 - 13:14:45)
OMAP34xx/35xx-GP ES1.0, CPU-OPP2 L3-165MHz
OMAP3 EVM board + LPDDR/NAND
Now,
U-Boot 2010.09 (Nov 07 2010 - 07:08:44)
OMAP3630/3730-GP ES1.0, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz
OMAP3 EVM board + LPDDR/NANDThat's ai improvement.
However, in your log, I see folloing:
[ 0.000000] Total of 96 interrupts on 1 active controller [ 0.000000] Could not get gpios_ick [ 0.000000] Could not get gpios_fckLooks like there are some changes - either in your
Kconfigor elsewhere in the code that "get" gpio clocks is failing.The SMSC chip is "virtually" non-existent for the Linux kernel here onwards.
Quoted 7 lines
My kernel version is "Linux-2.6.36-rc8-09072-g661df74-"
I have not yet looked at, but there is possible "break" on on mainline for EVM due to gpio related changes.
You could be experiencing this break...~sanjeev
[snip]
I tried building the latest on l-o master and was able to boot consistently in 4 times I tried. Didn't notice the gpio clock related error I noticed in your boot log.
U-Boot 2010.09 (Nov 08 2010 - 17:11:45)
OMAP3630/3730-GP ES2.0, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz OMAP3 EVM board + LPDDR/NAND
...
[ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/200/600 MHz [ 0.000000] Reprogramming SDRC clock to 200000000 Hz [ 0.000000] dpll3_m2_clk rate change failed: -22 [ 0.000000] GPMC revision 5.0 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts [ 0.000000] Total of 96 interrupts on 1 active controller [ 0.000000] OMAP GPIO hardware version 2.5 [ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar ... [ 2.061950] net eth0: SMSC911x/921x identified at 0xc8880000, IRQ: 336 [ 3.075561] Sending DHCP requests .., OK [ 5.169769] IP-Config: Got DHCP answer from 0.0.0.0, my address is xx.yy.zz.00(edited)
...
# uname -a Linux OMAP3EVM 2.6.37-rc1-08879-g9988a6b-dirty #1 Mon Nov 8 19:50:18 IST 2010 armv7l unknown #