Mistral AM37x (with AM3715) devel board networking broken
Hi Sanjeev,
Thanks much for the help.
Quoted 9 lines
I tried building the latest on l-o master and was able to boot consistently in 4 times I tried. Didn't notice the gpio clock related error I noticed in your boot log.
U-Boot 2010.09 (Nov 08 2010 - 17:11:45)
OMAP3630/3730-GP ES2.0, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz OMAP3 EVM board + LPDDR/NAND
Note that mine is ES1.0 (yours is ES2.0):
OMAP3630/3730-GP ES1.0, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz
Not sure if that's any clue.
Tonight I got the latest stuff:
git clone git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6.git
and built it up with:
make omap2plus_defconfig ARCH=arm
And got this
http://www.efn.org/~rick/pub/boot6.log
It's basically the same, I get the 3 warnings and sometimes eth0 works
and sometimes it doesn't. Note that my board works flawlessly with the kernel on the SD Card.
What compiler are you using? I tried CodeSourcery
2009q1 and 2010q1 with the same results.
How did you configure your u-boot?
Could you send me your boot up text? Could you send me your
u-boot.bin (and or your uImage) so I can try it? I might help me figure out what's going on.
Thanks again.
Rick
Quoted 11 lines · Rick Bronson
Hi Sanjeev,
Thanks much for the help.
Quoted 7 lines
I tried building the latest on l-o master and was able to boot consistently in 4 times I tried. Didn't notice the gpio clock related error I noticed in your boot log.
U-Boot 2010.09 (Nov 08 2010 - 17:11:45)
Quoted 9 lines
Quoted 2 lines
OMAP3630/3730-GP ES2.0, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz OMAP3 EVM board + LPDDR/NAND
Note that mine is ES1.0 (yours is ES2.0):
OMAP3630/3730-GP ES1.0, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz
Not sure if that's any clue.
That's interesting - there shouldn't b e an ES2.0 of the 3630/3730. The highest revision is an ES1.2.
Quoted 25 lines
Tonight I got the latest stuff:
git clone
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6.gitand built it up with:
make
omap2plus_defconfigARCH=armAnd got this
http://www.efn.org/~rick/pub/boot6.log
It's basically the same, I get the 3 warnings and sometimes eth0 works and sometimes it doesn't. Note that my board works flawlessly with the kernel on the SD Card.
What compiler are you using? I tried CodeSourcery 2009q1 and 2010q1 with the same results.
How did you configure your u-boot?
Could you send me your boot up text? Could you send me your u-boot.bin (and or your uImage) so I can try it? I might help me figure out what's going on.
Quoted 8 lines
Thanks again.
Rick
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Quoted 27 lines
-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of Gadiyar, Anand
Sent: Tuesday, November 09, 2010 10:32 AM
To: Rick Bronson
Cc: [email protected]; Premi, Sanjeev
Subject: Re: Mistral AM37x (with AM3715) devel board networking brokenQuoted 5 lines · Rick Bronson
Hi Sanjeev,
Thanks much for the help.
Quoted 1 line
I tried building the latest on l-o master and was able to
boot consistently
Quoted 1 line
Quoted 1 line
in 4 times I tried. Didn't notice the gpio clock related
error I noticed in
Quoted 10 lines
Quoted 7 lines
your boot log.
U-Boot 2010.09 (Nov 08 2010 - 17:11:45)
OMAP3630/3730-GP ES2.0, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz OMAP3 EVM board + LPDDR/NAND
Note that mine is ES1.0 (yours is ES2.0):
Quoted 9 lines
Quoted 4 lines
OMAP3630/3730-GP ES1.0, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz
Not sure if that's any clue.
That's interesting - there shouldn't b e an ES2.0 of the 3630/3730. The highest
revision is an ES1.2.
Now, I notice it too. Checking the u-boot sources now.
[snip]...[snip]
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Quoted 44 lines
-----Original Message-----
From: Rick Bronson [mailto:[email protected]]
Sent: Tuesday, November 09, 2010 10:24 AM
To: [email protected]
Cc: Premi, Sanjeev
Subject: RE: Mistral AM37x (with AM3715) devel board networking brokenHi Sanjeev,
Thanks much for the help.
Quoted 1 line
I tried building the latest on l-o master and was able to
boot consistently
Quoted 1 line
in 4 times I tried. Didn't notice the gpio clock related
error I noticed in
Quoted 7 lines
your boot log.
U-Boot 2010.09 (Nov 08 2010 - 17:11:45)
OMAP3630/3730-GP ES2.0, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz OMAP3 EVM board + LPDDR/NAND
Note that mine is ES1.0 (yours is ES2.0):
OMAP3630/3730-GP ES1.0, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz
Not sure if that's any clue.
Tonight I got the latest stuff:
git clone
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-oma
p-2.6.gitand built it up with:
make
omap2plus_defconfigARCH=armAnd got this
Quoted 7 lines
It's basically the same, I get the 3 warnings and sometimes
eth0 works
and sometimes it doesn't. Note that my board works flawlessly with the kernel on the SD Card.What compiler are you using? I tried CodeSourcery
2009q1 and 2010q1 with the same results.
[sp] I am mostly using 2009q1; but have use 2010q1 earlier in JUL;
didn't see any issues back then.
Quoted 2 lines
How did you configure your u-boot?
[sp] It is default configuration on the u-boot master.
Quoted 4 lines
Could you send me your boot up text? Could you send me your
u-boot.bin (and or your uImage) so I can try it? I might help me figure out what's going on.
[sp] Will send offline
~sanjeev
Quoted 5 lines
Thanks again.
Rick