Poor SCSI drive performance on SMP machine, 2.2.16
A message that is not in the archive (sent off-list or not yet received): [email protected]
Here is the output from dmesg. How do I tell if it is improperly terminated?
Thanks, Para-dox ([email protected])
----- Original Message -----
From: "Michael Brown" <[email protected]>
To: <[email protected]>
Sent: Sunday, January 28, 2001 11:12 PM
Subject: Re: Poor SCSI drive performance on SMP machine, 2.2.16
Quoted 12 lines
Your problem appears to be improper SCSI termination.
You need to either
1) make sure your SCSI drive has termination enabled
or
2) move your SCSI drive to the middle connector and put a terminator on
the last connectorCheck your syslog and post to l-k the part where it detects your drives. I'll bet the adapter is throttling back quite dramatically in the presence of improper termination.
Quoted 7 lines
--
Michael Brown_________________________________________________________________
Get your FREE download of MSN Explorer at http://explorer.msn.com
(scsi0) <Adaptec AIC-7890/1 Ultra2 SCSI host adapter> found at PCI 0/12/0 (scsi0) Wide Channel, SCSI ID=7, 32/255 SCBs
(scsi0) Downloading sequencer code... 392 instructions downloaded scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.31/3.2.4
<Adaptec AIC-7890/1 Ultra2 SCSI host adapter>
scsi : 1 host.
(scsi0:0:0:0) Synchronous at 40.0 Mbyte/sec, offset 15.
Vendor: IBM Model: DGHS09U Rev: 0350
Type: Direct-Access ANSI SCSI revision: 03
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
scsi : detected 1 SCSI disk total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 17916240 [8748 MB] [8.7 GB] Partition check:
sda: sda1 sda2 sda3
Quoted 2 lines · "paradox3" <[email protected]> writes:
Here is the output from dmesg. How do I tell if it is improperly terminated?
you never gave the model of the hard drive (or if you did, i didn't see it), but you did say a 10k rpm ibm. i am going to assume it is u2w/lvd capable. no lvd hard drive has termination built in. you must use a seperate termination device at the end of the ribbon. or you can use a terminating cable. since your controller is a single-ended device, get a single-ended, wide, active terminator and plug it into the end of the ribbon. put the hard drive in the middle somewhere.
see <URL:http://www.scsifaq.org/> for more information.
Quoted 32 lines
Thanks, Para-dox ([email protected])
----- Original Message -----
From: "Michael Brown" <[email protected]>
To: <[email protected]>
Sent: Sunday, January 28, 2001 11:12 PM
Subject: Re: Poor SCSI drive performance on SMP machine, 2.2.16Quoted 19 lines
Your problem appears to be improper SCSI termination.
You need to either
1) make sure your SCSI drive has termination enabled
or
2) move your SCSI drive to the middle connector and put a terminator on
the last connectorCheck your syslog and post to l-k the part where it detects your drives. I'll bet the adapter is throttling back quite dramatically in the presence of improper termination.
--
Michael Brown_________________________________________________________________
Get your FREE download of MSN Explorer at http://explorer.msn.com
Signature · 7 lines
J o h a n K u l l s t a m [[email protected]] Don't Fear the Penguin! - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected] Please read the FAQ at http://www.tux.org/lkml/