ALC892 Support (Intel HDA) - HDMI
Hello-
I'm trying to get my Realtek ALC892 chip to work according to it's specifications over HDMI. The manufacturers site say it should be able to do 7.1+2 channels, 24bit audio and 192Khz sample rate. However, it seems that the ALSA drivers (even the ones from the realtek website) limit the output to 2 channels, 16bit, 88.2KHz.
Here is my system information that you can see these results:
http://www.alsa-project.org/db/?f=5b55a63fea6580dfcbf1a85c7c734f977df798f1
I see the ALC892 as being supported in the ALSA changelog, but I don't see any model options in Documentation/HD-Audio-Models.txt. I'm currently using "options snd-hda-intel model=6stack-digout" (as I have 6-jack with a SPDIF out on the motherboard) but I'm not sure that is actually doing anything.
What's the *actual* support of this chipset? Is what I'm getting now the best I should expect over HDMI? I saw support in ALSA and bought the motherboard expecting it to be fully supported since the changelogs say support was added.
I also tried with an ALC887 chipset as well, and got basically the same results.
Any help getting this to work would be appreciated. Let me know if there's any other information required.
Thank you-
Jeremy
2011/5/16 Jeremy Bush <[email protected]>
Quoted 5 lines
Hello-
I'm trying to get my Realtek ALC892 chip to work according to it's specifications over HDMI. The manufacturers site say it should be able to do 7.1+2 channels, 24bit audio and 192Khz sample rate.
7.1 is provided by 4 jack at rear panel ( green, black, orange and grey) 2 is provided by headphone at front panel
Quoted 13 lines
However, it seems that the ALSA drivers (even the ones from the realtek website) limit the output to 2 channels, 16bit, 88.2KHz.
Here is my system information that you can see these results:
http://www.alsa-project.org/db/?f=5b55a63fea6580dfcbf1a85c7c734f977df798f1
I see the ALC892 as being supported in the ALSA changelog, but I don't see any model options in
Documentation/HD-Audio-Models.txt. I'm currently using "options snd-hda-intel model=6stack-digout" (as I have 6-jack with a SPDIF out on the motherboard) but I'm not sure that is actually doing anything.
As your codec info does not have "Side Playback Channel" and "Side Playback Switch", it look like the model is used for 5stack motherboard which support 5.1
Do you hear any noise since Valerio reported noise appear when using the model=auto in
http://thread.gmane.org/gmane.linux.alsa.devel/84653/focus=84724
Quoted 1 line
What's the *actual* support of this chipset?
Node 0x1e [Pin Complex] wcaps 0x400781: Stereo Digital
Pincap 0x00000010: OUT
Pin Default 0x014b1130: [Jack] SPDIF Out at Ext Rear
Conn = Comb, Color = Black
DefAssociation = 0x3, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1
0x06
Quoted 4 lines
Is what I'm getting now the best I should expect over HDMI? I saw support in ALSA and bought the motherboard expecting it to be fully supported since the changelogs say support was added.
Codec: Intel CougarPoint HDMI
Address: 3
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x80862805
Subsystem Id: 0x80862805
Revision Id: 0x100000
No Modem Function Group found
Node 0x03 [Audio Output] wcaps 0x6611: 8-Channels Digital
Control: name="IEC958 Playback Con Mask", index=1, device=0
Control: name="IEC958 Playback Pro Mask", index=1, device=0
Control: name="IEC958 Playback Default", index=1, device=0
Control: name="IEC958 Playback Switch", index=1, device=0
Device: name="HDMI 0", type="HDMI", device=3
Converter: stream=8, channel=0
Digital: Enabled
Digital category: 0x0
PCM:
rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
bits [0x1e]: 16 20 24 32
formats [0x5]: PCM AC3 Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Node 0x06 [Pin Complex] wcaps 0x40778d: 8-Channels Digital Amp-Out CP
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x00 0x00]
Pincap 0x09000094: OUT Detect HBR HDMI DP
Pin Default 0x18560020: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x2, Sequence = 0x0
Pin-ctls: 0x40: OUT
Unsolicited: tag=06, enabled=1
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1
0x03
Quoted 6 lines
I also tried with an ALC887 chipset as well, and got basically the same results.
Any help getting this to work would be appreciated. Let me know if there's any other information required.
[ 2.090473] HDMI: detected monitor at connection type HDMI
[ 2.090475] HDMI: available speakers: FL/FR [ 2.090477] HDMI: supports coding type LPCM: channels = 2, rates = 44100 48000 88200, bits = 16 [ 2.090480] HDMI hot plug event: Pin=6 Presence_Detect=1 ELD_Valid=1 [ 2.091104] PM: Hibernation image not present or could not be loaded. [ 2.091458] Magic number: 11:515:605 [ 2.094010] HDMI: detected monitor at connection type HDMI [ 2.094103] HDMI: available speakers: FL/FR [ 2.094191] HDMI: supports coding type LPCM: channels = 2, rates =
44100 48000 88200, bits = 16
Quoted 4 lines
Thank you-
Jeremy
Quoted 11 lines · Raymond Yau
2011/5/16 Jeremy Bush <[email protected]>
Quoted 5 lines
Hello-
I'm trying to get my Realtek ALC892 chip to work according to it's specifications over HDMI. The manufacturers site say it should be able to do 7.1+2 channels, 24bit audio and 192Khz sample rate.
7.1 is provided by 4 jack at rear panel ( green, black, orange and grey) 2 is provided by headphone at front panel
OK, so that has nothing to do with HDMI then.
Quoted 13 lines
Quoted 13 lines
However, it seems that the ALSA drivers (even the ones from the realtek website) limit the output to 2 channels, 16bit, 88.2KHz.
Here is my system information that you can see these results:
http://www.alsa-project.org/db/?f=5b55a63fea6580dfcbf1a85c7c734f977df798f1
I see the ALC892 as being supported in the ALSA changelog, but I don't see any model options in
Documentation/HD-Audio-Models.txt. I'm currently using "options snd-hda-intel model=6stack-digout" (as I have 6-jack with a SPDIF out on the motherboard) but I'm not sure that is actually doing anything.
Quoted 8 lines
As your codec info does not have "Side Playback Channel" and "Side Playback Switch", it look like the model is used for 5stack motherboard which support 5.1
Do you hear any noise since Valerio reported noise appear when using the model=auto in
http://thread.gmane.org/gmane.linux.alsa.devel/84653/focus=84724
I'm not actually trying to get analog working or the front-panel output. Only surround sound over HDMI. I have tried model=auto and didn't notice anything different than specifying the model.
Quoted 42 lines
Quoted 3 lines
Is what I'm getting now the best I should expect over HDMI? I saw support in ALSA and bought the motherboard expecting it to be fully supported since the changelogs say support was added.
Codec: Intel CougarPoint HDMI
Address: 3
AFG Function Id:0x1(unsol 0)
Vendor Id:0x80862805
Subsystem Id:0x80862805
Revision Id:0x100000
No Modem Function Group foundNode
0x03[Audio Output] wcaps0x6611: 8-Channels DigitalControl: name="IEC958 Playback Con Mask", index=1, device=0
Control: name="IEC958 Playback Pro Mask", index=1, device=0
Control: name="IEC958 Playback Default", index=1, device=0
Control: name="IEC958 Playback Switch", index=1, device=0
Device: name="HDMI 0", type="HDMI", device=3
Converter: stream=8, channel=0
Digital: Enabled
Digital category:0x0
PCM:rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000 bits [0x1e]: 16 20 24 32 formats [0x5]: PCM AC3Power states: D0 D3 EPSS
Power: setting=D0, actual=D0Node
0x06[Pin Complex] wcaps0x40778d: 8-Channels Digital Amp-Out CP
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x000x00]
Pincap0x09000094: OUT Detect HBR HDMI DP
Pin Default0x18560020: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation =0x2, Sequence =0x0
Pin-ctls:0x40: OUT
Unsolicited: tag=06, enabled=1
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1
Quoted 1 line
0x03
So this seems to say I should be getting 7.1 over the HDMI output. What do I need to change in my config to actually get it? I tried messing around with /sys/class/sound/hwC1D3/user_pin_configs but I'm not sure what to change.
Jeremy
2011/5/16 Jeremy Bush <[email protected]>
Quoted 79 lines
Quoted 6 lines
Quoted 6 lines
However, it seems that the ALSA drivers (even the ones from the realtek website) limit the output to 2 channels, 16bit, 88.2KHz.
Here is my system information that you can see these results:
http://www.alsa-project.org/db/?f=5b55a63fea6580dfcbf1a85c7c734f977df798f1
Quoted 2 lines
Quoted 2 lines
I see the ALC892 as being supported in the ALSA changelog, but I don't
see
Quoted 1 line
Quoted 1 line
any model options in
Documentation/HD-Audio-Models.txt. I'm currentlyusing
Quoted 1 line
Quoted 1 line
"options snd-hda-intel model=6stack-digout" (as I have 6-jack with a
SPDIF
Quoted 1 line
Quoted 1 line
out on the motherboard) but I'm not sure that is actually doing
anything.
Quoted 3 lines
Quoted 2 lines
As your codec info does not have "Side Playback Channel" and "Side
Playback
Quoted 1 line
Switch", it look like the model is used for 5stack motherboard which
support
Quoted 6 lines
5.1
Do you hear any noise since Valerio reported noise appear when using the model=auto in
http://thread.gmane.org/gmane.linux.alsa.devel/84653/focus=84724
I'm not actually trying to get analog working or the front-panel output. Only surround sound over HDMI. I have tried model=auto and didn't notice anything different than specifying the model.
Quoted 1 line
Quoted 1 line
Is what I'm getting now the best I should expect over HDMI? I saw
support
Quoted 1 line
Quoted 1 line
in ALSA and bought the motherboard expecting it to be fully supported
since
Quoted 40 lines
Quoted 1 line
the changelogs say support was added.
Codec: Intel CougarPoint HDMI
Address: 3
AFG Function Id:0x1(unsol 0)
Vendor Id:0x80862805
Subsystem Id:0x80862805
Revision Id:0x100000
No Modem Function Group foundNode
0x03[Audio Output] wcaps0x6611: 8-Channels DigitalControl: name="IEC958 Playback Con Mask", index=1, device=0
Control: name="IEC958 Playback Pro Mask", index=1, device=0
Control: name="IEC958 Playback Default", index=1, device=0
Control: name="IEC958 Playback Switch", index=1, device=0
Device: name="HDMI 0", type="HDMI", device=3
Converter: stream=8, channel=0
Digital: Enabled
Digital category:0x0
PCM:rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000 bits [0x1e]: 16 20 24 32 formats [0x5]: PCM AC3Power states: D0 D3 EPSS
Power: setting=D0, actual=D0Node
0x06[Pin Complex] wcaps0x40778d: 8-Channels Digital Amp-Out CP
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x000x00]
Pincap0x09000094: OUT Detect HBR HDMI DP
Pin Default0x18560020: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation =0x2, Sequence =0x0
Pin-ctls:0x40: OUT
Unsolicited: tag=06, enabled=1
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1Quoted 1 line
0x03
Quoted 6 lines
So this seems to say I should be getting 7.1 over the HDMI output. What do I need to change in my config to actually get it? I tried messing around with
/sys/class/sound/hwC1D3/user_pin_configsbut I'm not sure what to change.
Do your hdmi monitor support 7.1 ?
[ 2.090473] HDMI: detected monitor at connection type HDMI [ 2.090475] HDMI: available speakers: FL/FR [ 2.090477] HDMI: supports coding type LPCM: channels = 2, rates = 44100 48000 88200, bits = 16 [ 2.090480] HDMI hot plug event: Pin=6 Presence_Detect=1 ELD_Valid=1
Quoted 87 lines · Raymond Yau
2011/5/16 Jeremy Bush <[email protected]>
Quoted 79 lines
Quoted 6 lines
Quoted 6 lines
However, it seems that the ALSA drivers (even the ones from the realtek website) limit the output to 2 channels, 16bit, 88.2KHz.
Here is my system information that you can see these results:
http://www.alsa-project.org/db/?f=5b55a63fea6580dfcbf1a85c7c734f977df798f1
Quoted 2 lines
Quoted 2 lines
I see the ALC892 as being supported in the ALSA changelog, but I don't
see
Quoted 1 line
Quoted 1 line
any model options in
Documentation/HD-Audio-Models.txt. I'm currentlyusing
Quoted 1 line
Quoted 1 line
"options snd-hda-intel model=6stack-digout" (as I have 6-jack with a
SPDIF
Quoted 1 line
Quoted 1 line
out on the motherboard) but I'm not sure that is actually doing
anything.
Quoted 3 lines
Quoted 2 lines
As your codec info does not have "Side Playback Channel" and "Side
Playback
Quoted 1 line
Switch", it look like the model is used for 5stack motherboard which
support
Quoted 6 lines
5.1
Do you hear any noise since Valerio reported noise appear when using the model=auto in
http://thread.gmane.org/gmane.linux.alsa.devel/84653/focus=84724
I'm not actually trying to get analog working or the front-panel output. Only surround sound over HDMI. I have tried model=auto and didn't notice anything different than specifying the model.
Quoted 1 line
Quoted 1 line
Is what I'm getting now the best I should expect over HDMI? I saw
support
Quoted 1 line
Quoted 1 line
in ALSA and bought the motherboard expecting it to be fully supported
since
Quoted 28 lines
Quoted 1 line
the changelogs say support was added.
Codec: Intel CougarPoint HDMI
Address: 3
AFG Function Id:0x1(unsol 0)
Vendor Id:0x80862805
Subsystem Id:0x80862805
Revision Id:0x100000
No Modem Function Group foundNode
0x03[Audio Output] wcaps0x6611: 8-Channels DigitalControl: name="IEC958 Playback Con Mask", index=1, device=0
Control: name="IEC958 Playback Pro Mask", index=1, device=0
Control: name="IEC958 Playback Default", index=1, device=0
Control: name="IEC958 Playback Switch", index=1, device=0
Device: name="HDMI 0", type="HDMI", device=3
Converter: stream=8, channel=0
Digital: Enabled
Digital category:0x0
PCM:
rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000 bits [0x1e]: 16 20 24 32
formats [0x5]: PCM AC3
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0Quoted 13 lines
Node
0x06[Pin Complex] wcaps0x40778d: 8-Channels Digital Amp-Out CP Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x000x00]
Pincap0x09000094: OUT Detect HBR HDMI DP
Pin Default0x18560020: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation =0x2, Sequence =0x0
Pin-ctls:0x40: OUT
Unsolicited: tag=06, enabled=1
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1
0x03Quoted 6 lines
So this seems to say I should be getting 7.1 over the HDMI output. What do I need to change in my config to actually get it? I tried messing around with
/sys/class/sound/hwC1D3/user_pin_configsbut I'm not sure what to change.
Quoted 7 lines
Do your hdmi monitor support 7.1 ?
[ 2.090473] HDMI: detected monitor at connection type HDMI [ 2.090475] HDMI: available speakers: FL/FR [ 2.090477] HDMI: supports coding type LPCM: channels = 2, rates = 44100 48000 88200, bits = 16 [ 2.090480] HDMI hot plug event: Pin=6 Presence_Detect=1 ELD_Valid=1
Yes, it's connected to an Onkyo TX-SR607 7.2-Channel receiver.
Jeremy
Quoted 92 lines · Jeremy Bush
Quoted 89 lines · Raymond Yau
2011/5/16 Jeremy Bush <[email protected]>
Quoted 79 lines
Quoted 6 lines
Quoted 6 lines
However, it seems that the ALSA drivers (even the ones from the realtek website) limit the output to 2 channels, 16bit, 88.2KHz.
Here is my system information that you can see these results:
http://www.alsa-project.org/db/?f=5b55a63fea6580dfcbf1a85c7c734f977df798f1
Quoted 2 lines
Quoted 2 lines
I see the ALC892 as being supported in the ALSA changelog, but I don't
see
Quoted 1 line
Quoted 1 line
any model options in
Documentation/HD-Audio-Models.txt. I'm currentlyusing
Quoted 1 line
Quoted 1 line
"options snd-hda-intel model=6stack-digout" (as I have 6-jack with a
SPDIF
Quoted 1 line
Quoted 1 line
out on the motherboard) but I'm not sure that is actually doing
anything.
Quoted 3 lines
Quoted 2 lines
As your codec info does not have "Side Playback Channel" and "Side
Playback
Quoted 1 line
Switch", it look like the model is used for 5stack motherboard which
support
Quoted 6 lines
5.1
Do you hear any noise since Valerio reported noise appear when using the model=auto in
http://thread.gmane.org/gmane.linux.alsa.devel/84653/focus=84724
I'm not actually trying to get analog working or the front-panel output. Only surround sound over HDMI. I have tried model=auto and didn't notice anything different than specifying the model.
Quoted 1 line
Quoted 1 line
Is what I'm getting now the best I should expect over HDMI? I saw
support
Quoted 1 line
Quoted 1 line
in ALSA and bought the motherboard expecting it to be fully supported
since
Quoted 28 lines
Quoted 1 line
the changelogs say support was added.
Codec: Intel CougarPoint HDMI
Address: 3
AFG Function Id:0x1(unsol 0)
Vendor Id:0x80862805
Subsystem Id:0x80862805
Revision Id:0x100000
No Modem Function Group foundNode
0x03[Audio Output] wcaps0x6611: 8-Channels DigitalControl: name="IEC958 Playback Con Mask", index=1, device=0
Control: name="IEC958 Playback Pro Mask", index=1, device=0
Control: name="IEC958 Playback Default", index=1, device=0
Control: name="IEC958 Playback Switch", index=1, device=0
Device: name="HDMI 0", type="HDMI", device=3
Converter: stream=8, channel=0
Digital: Enabled
Digital category:0x0
PCM:
rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000 bits [0x1e]: 16 20 24 32
formats [0x5]: PCM AC3
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0Quoted 13 lines
Node
0x06[Pin Complex] wcaps0x40778d: 8-Channels Digital Amp-Out CP Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x000x00]
Pincap0x09000094: OUT Detect HBR HDMI DP
Pin Default0x18560020: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation =0x2, Sequence =0x0
Pin-ctls:0x40: OUT
Unsolicited: tag=06, enabled=1
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1
0x03Quoted 6 lines
So this seems to say I should be getting 7.1 over the HDMI output. What do I need to change in my config to actually get it? I tried messing around with
/sys/class/sound/hwC1D3/user_pin_configsbut I'm not sure what to change.Do your hdmi monitor support 7.1 ?
Quoted 8 lines
Quoted 5 lines
[ 2.090473] HDMI: detected monitor at connection type HDMI [ 2.090475] HDMI: available speakers: FL/FR [ 2.090477] HDMI: supports coding type LPCM: channels = 2, rates = 44100 48000 88200, bits = 16 [ 2.090480] HDMI hot plug event: Pin=6 Presence_Detect=1 ELD_Valid=1Yes, it's connected to an Onkyo TX-SR607 7.2-Channel receiver.
I've also upgraded to the latest nightly build of alsa, and still experience the same behavior.
Jeremy
A message that is not in the archive (sent off-list or not yet received): [email protected]
2011/5/18 Jeremy Bush <[email protected]>:
Quoted 101 lines · Jeremy Bush
Quoted 99 lines · Raymond Yau
Quoted 95 lines
2011/5/16 Jeremy Bush <[email protected]>
Quoted 79 lines
Quoted 6 lines
Quoted 6 lines
However, it seems that the ALSA drivers (even the ones from the realtek website) limit the output to 2 channels, 16bit, 88.2KHz.
Here is my system information that you can see these results:
http://www.alsa-project.org/db/?f=5b55a63fea6580dfcbf1a85c7c734f977df798f1
Quoted 2 lines
Quoted 2 lines
I see the ALC892 as being supported in the ALSA changelog, but I don't
see
Quoted 1 line
Quoted 1 line
any model options in
Documentation/HD-Audio-Models.txt. I'm currentlyusing
Quoted 1 line
Quoted 1 line
"options snd-hda-intel model=6stack-digout" (as I have 6-jack with a
SPDIF
Quoted 1 line
Quoted 1 line
out on the motherboard) but I'm not sure that is actually doing
anything.
Quoted 3 lines
Quoted 2 lines
As your codec info does not have "Side Playback Channel" and "Side
Playback
Quoted 1 line
Switch", it look like the model is used for 5stack motherboard which
support
Quoted 6 lines
5.1
Do you hear any noise since Valerio reported noise appear when using the model=auto in
http://thread.gmane.org/gmane.linux.alsa.devel/84653/focus=84724
I'm not actually trying to get analog working or the front-panel output. Only surround sound over HDMI. I have tried model=auto and didn't notice anything different than specifying the model.
Quoted 1 line
Quoted 1 line
Is what I'm getting now the best I should expect over HDMI? I saw
support
Quoted 1 line
Quoted 1 line
in ALSA and bought the motherboard expecting it to be fully supported
since
Quoted 28 lines
Quoted 1 line
the changelogs say support was added.
Codec: Intel CougarPoint HDMI
Address: 3
AFG Function Id:0x1(unsol 0)
Vendor Id:0x80862805
Subsystem Id:0x80862805
Revision Id:0x100000
No Modem Function Group foundNode
0x03[Audio Output] wcaps0x6611: 8-Channels DigitalControl: name="IEC958 Playback Con Mask", index=1, device=0
Control: name="IEC958 Playback Pro Mask", index=1, device=0
Control: name="IEC958 Playback Default", index=1, device=0
Control: name="IEC958 Playback Switch", index=1, device=0
Device: name="HDMI 0", type="HDMI", device=3
Converter: stream=8, channel=0
Digital: Enabled
Digital category:0x0
PCM:
rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000 bits [0x1e]: 16 20 24 32
formats [0x5]: PCM AC3
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0Quoted 13 lines
Node
0x06[Pin Complex] wcaps0x40778d: 8-Channels Digital Amp-Out CP Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x000x00]
Pincap0x09000094: OUT Detect HBR HDMI DP
Pin Default0x18560020: [Jack] Digital Out at Int HDMI Conn = Digital, Color = Unknown
DefAssociation =0x2, Sequence =0x0
Pin-ctls:0x40: OUT
Unsolicited: tag=06, enabled=1
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1
0x03Quoted 6 lines
So this seems to say I should be getting 7.1 over the HDMI output. What do I need to change in my config to actually get it? I tried messing around with
/sys/class/sound/hwC1D3/user_pin_configsbut I'm not sure what to change.Do your hdmi monitor support 7.1 ?
[ 2.090473] HDMI: detected monitor at connection type HDMI[ 2.090475] HDMI: available speakers: FL/FR
[ 2.090477] HDMI: supports coding type LPCM: channels = 2, rates = 44100 48000 88200, bits = 16
[ 2.090480] HDMI hot plug event: Pin=6 Presence_Detect=1 ELD_Valid=1
Quoted 6 lines
Quoted 1 line
Yes, it's connected to an Onkyo TX-SR607 7.2-Channel receiver.
I've also upgraded to the latest nightly build of alsa, and still experience the same behavior.
Jeremy
you have to check the video driver since it is the video driver query hdmi monitor and pass back ELD to audio driver
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
[ 2.090475] HDMI: available speakers: FL/FR [ 2.090477] HDMI: supports coding type LPCM: channels = 2, rates =44100 48000 88200, bits = 16