Skip to contentSkip to conversation

Porting U-Boot to AMCC 440 Spe

U-Boot-Users William Oppermann 2 participants 2 messages Dec 11, 2006

lore
Share & tools
lore
#0 lore raw

Has anybody ported U-Boot to the AMCC 440-Spe processor at PVR version 53421891.

1. We have an AMCC Yucca board using a processor with PVR 53421890 (revA silicon), the start.s code runs fine.

2. When running this same code on our board with PVR version 53421891 (revB silicon) we always have an ESR set to 0x8000000, as soon as we enable the MSR[ME] Bit is set we of course get a machine check.

3. We have tried a Denx patch to write all three words of the TLB table (to make sure no parity errors are occuring) however we still have the problem.

4. We have applied a Denx patch to write the TLB table depending on whether its revA or revB silicon.

Neither patch has cured the problem?

Has anybody seen this issue ?

William Oppermann

--
No virus found in this outgoing message.
Checked by AVG Free Edition.
Version: 7.1.409 / Virus Database: 268.15.15/581 - Release Date: 09/12/2006 -------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.denx.de/pipermail/u-boot/attachments/20061211/09bb7abb/attachment.htm
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: image/jpeg
Size: 11201 bytes
Desc: not available
Url : http://lists.denx.de/pipermail/u-boot/attachments/20061211/09bb7abb/attachment.jpeg

#1 lore raw
Quoted 3 lines · In message <[email protected]> you wrote:

Has anybody ported U-Boot to the AMCC 440-Spe processor at PVR version 53421891.

U-Boot is running fine on a Yucca Rev. B here:

U-Boot 1.1.5 (Nov 10 2006 - 08:45:01)

CPU: AMCC PowerPC 440SPe Rev. B at 533.328 MHz (PLB=133, OPB=66, EBC=66 MHz)
I2C boot EEPROM enabled
Bootstrap Option C - Boot ROM Location I2C (Addr 0x54) Internal PCI arbiter enabled
32 kB I-Cache 32 kB D-Cache

Board: Yucca - AMCC 440SPe Evaluation Board
I2C:   ready
DRAM:  1024 MB
FLASH:  5 MB
PCI:   Bus Dev VenId DevId Class Int
        00  01  1000  0054  0100  00
PCIE:1 successfully set as rootpoint
        01  01  1095  3132  0180  00
PCIE:2 successfully set as rootpoint
        02  01  1095  3132  0180  00
In:    serial
Out:   serial
Err:   serial
Net:   ppc_4xx_eth0

Type "run flash_nfs" to mount root filesystem over NFS

Hit any key to stop autoboot: 0

Quoted 11 lines

2. When running this same code on our board with PVR version 53421891 (revB silicon) we always have an ESR set to 0x8000000, as soon as we enable the MSR[ME] Bit is set we of course get a machine check.

3. We have tried a Denx patch to write all three words of the TLB table (to make sure no parity errors are occuring) however we still have the problem.

4. We have applied a Denx patch to write the TLB table depending on whether its revA or revB silicon.

Neither patch has cured the problem?

Please make sure to use a current version of the U-Boot code. Support
for 440SPe rev. B. needs at least the version tagged as
LABEL_2006_06_30_2020, or better top of tree in the git repo.

Best regards,

Wolfgang Denk

Signature · 3 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
How much net work could a network work, if a network could net work?