Kernel Panic: too few segs for DMA mapping increase AHC_NSEG
Hi everybody.
I have just upgraded my PC from 768MB RAM to 1GB.
I have recompiled the kernel (2.4.14) for hi mem support (4GB).
Now it's appening a very strange behaviour.
I have several file system on the same disk (vfat file system). I have compiled vfat driver as a module. So before try to mount I must issue a 'modprobe vfat'. I'm using Slackware 8.0. modutils version is 2.4.6
Then if I try to copy a file from that filesystem to the root filesystem I get this error:
Kernel panic: too few segs for DMA mappings increase AHC_NSEG
Usually this is the procedure:
root login
modprobe vfat
mount /dev/sda2 /mnt (to mount the fat partition)
cd /usr/src
cp /mnt/linux/kernel/linux-2.2.20.tar.bz2 . (I want to copy kernel source tarball from the vfat partition to /usr/src) CRASH..........
My MB is ABIT KT7A (bios rev ID 65 11/07/2001). Two 512 MB SDRAM (takei).
Other HW: AHA 39160, SCSI IBM HD DDYS 18130, Matrox G450. gcc version 2.95.3, binutils 2.10.91.0.4 (***not the original slack 8.0***, I have downgraded it for Oracle 9i)
If I compile a kernel without hi mem support all is fine.
Quoted 10 lines · Marco Berizzi
Hi everybody.
I have just upgraded my PC from 768MB RAM to 1GB.
I have recompiled the kernel (2.4.14) for hi mem support (4GB).Now it's appening a very strange behaviour.
I have several file system on the same disk (vfat file system). I have compiled vfat driver as a module. So before try to mount I must issue a 'modprobe vfat'. I'm using Slackware 8.0. modutils version is 2.4.6
Quoted 4 lines
Then if I try to copy a file from that filesystem to the root filesystem I get this error:
Kernel panic: too few segs for DMA mappings increase AHC_NSEG
Aha! Finally someone that can provoke this easily. Could you please apply attached patch and reproduce? Thanks.
Signature · 1 line
Jens Axboe
scsi/aic7xxx/aic7xxx_linux.c renamed from scsi/aic7xxx/aic7xxx_linux.c~ +13 -3
@@ -624,9 +624,10 @@ {int consumed; -if ((scb->sg_count +1 ) >AHC_NSEG ) -panic ("Too few segs for dma mapping. " -"Increase AHC_NSEG\n" ); +if ((scb->sg_count +1 ) >AHC_NSEG ) { +printk ("Too few segs for dma mapping. Increase AHC_NSEG\n" ); +return -1 ; + } consumed =1 ; sg->addr =ahc_htole32 (addr &0xFFFFFFFF );
@@ -1674,6 +1675,13 @@ len =sg_dma_len (cur_seg); consumed =ahc_linux_map_seg (ahc, scb, sg, addr, len); +if (consumed ==-1 ) { + printk("aic7xxx: scsi segs %d, + pci segs %d, aic segs %d\n", + cmd->use_sg, nseg, + scb->sg_count); +BUG (); + } sg += consumed; scb->sg_count += consumed; cur_seg++;
@@ -1705,6 +1713,8 @@ scb->sg_count =ahc_linux_map_seg (ahc, scb, sg, addr, cmd->request_bufflen); +if (scb->sg_count ==-1 ) +BUG (); sg->len |=ahc_htole32 (AHC_DMA_LAST_SEG );/*
...not good news.
Same behaviour: without hi mem support all right. With hi mem support (4GB) I get this error on console, after a kernel dump:
SCSI1:0:0:0 attempt to queue an abort message
SCSI1:0:0:0 command not foundaic7xxx_abort returns 0x2002
Then the system freeze completely, so I press the reset button. At the startup INIT calls fsck and when the checking is at about 55% it displays this message:
SCSI1:A:0:0 locking max tag count at 128
then the following startup procedure goes well.
I want to tell you that with this kernel (hi mem support enabled), all is working perfectly (I can compile a new working kernel, for example). X Window (4.1) plus kde is working well.
Only when I mount a vfat filesystem type and then I try to copy a file to the root partition I get this error.
Another point: I usually build only mass storage driver in the kernel (Adaptec AHA 39160 bios rev 3.10). I build as modules all other HW (nic, sound, USB), however only the SB PCI512 is loaded in this situation. I haven't any IDE device just one SCSI HD (IBM DDYS-T18350N firmware rev S93E) and one Plextor SCSI cdrom (UltraPlex 40max PX-40TS firmware revision 1.04).
----- Original Message -----
From: "Jens Axboe" <[email protected]>
To: "Marco Berizzi" <[email protected]>
Cc: <[email protected]>
Sent: Monday, November 19, 2001 10:44 AM
Subject: Re: Kernel Panic: too few segs for DMA mapping increase AHC_NSEG
Quoted 8 lines · Marco Berizzi
Quoted 7 lines
Hi everybody.
I have just upgraded my PC from 768MB RAM to 1GB.
I have recompiled the kernel (2.4.14) for hi mem support (4GB).Now it's appening a very strange behaviour.
I have several file system on the same disk (vfat file system). I
have
Quoted 1 line
Quoted 1 line
compiled vfat driver as a module. So before try to mount I must
issue a
Quoted 3 lines
Quoted 3 lines
'modprobe vfat'. I'm using Slackware 8.0. modutils version is 2.4.6
Then if I try to copy a file from that filesystem to the root
filesystem
Quoted 11 lines
Quoted 3 lines
I get this error:
Kernel panic: too few segs for DMA mappings increase AHC_NSEGAha! Finally someone that can provoke this easily. Could you please apply attached patch and reproduce? Thanks.
--
Jens Axboe