(bug report) HWMON & Thermal interactions
Subsystems (2)
Hi,
Starting with v6.1-rc1 the SCMI HWMON driver failed probing on my JUNO due to the fact that no trip points were (ever !) defined in the DT; bisecting it looks like that after:
https://lore.kernel.org/all/[email protected]/
the presence of the mandatory trips node within thermal zones is now enforced.
So, this is NOT what this bug report is about (I'll post soon patches for the JUNO DT missing trips) BUT once this problem was solved in the DT, another issue appeared:
[ 1.921929] hwmon hwmon0: temp2_input not attached to any thermal zone
that despite having now a goodi/valid DT describing 2 sensors and 2 thermal zones embedding that sensors, only the first one is found as belonging to one ThermZ. (this happens ALSO with v6.0 once I added the trips...)
Digging deep into this, it turned out that inside the call chain
devm_hwmon_device_register_with_info
hwmon_device_register_with_info
__hwmon_device_register hwmon_thermal_register_sensors(dev) --> hwmon_thermal_add_sensor(dev, j) --> devm_thermal_of_zone_register(dev, sensor_id, tdata, )
the HWMON channel index j is passed to the Thermal framework in order to search and bind sensors with defined thermal zone, but this lead to the assumption that sequential HWMON channel indexes corresponds one-to-one to the underlying real sensor IDs that the ThermalFramework uses for matching within the DT.
On a system like my SCMI-based DT where I have 2 temp-sensors bound to 2 thermal zones like:
thernal_zones {
pmic {
...
thermal-sensors = <&scmi_sensors0 0>;
...
trips {
...
}
soc {
...
thermal-sensors = <&scmi_sensors0 3>;
...
trips {
...
}
}
}This works fine by chance for the pmic (j=0, sensor_id=0) BUT cannot work for the soc where J=1 BUT the real sensor ID is 3.
Note that there can be a number of sensors, not all of them of a type handled by HWMON, and enumerated by SCMI in different ways depending on the platform.
I suppose this is not an SCMI-only related issue, but maybe in non-SCMI context, where sensors are purely defined in the DT, the solution can be more easily attained (i.e. renumber the sensors).
At first I tried to solve this inside scmi-hwmon.c BUT I could not find a way to present to the HWMON subsystem the list of sensors preserving the above index/sensor_id matching (not even with a hack like passing down dummy sensors to the HWMON subsystem to fill the 'holes' in the numbering)
My tentative solution, which works fine for me in my context, was to add an optional HWMON hwops, so that the core hwmon can retrieve if needed the real sensor ID if different from the channel index (using an optional hwops instead of some static hwinfo var let me avoid to have to patch all the existent hwmon drivers that happens to just work fine as of today...but maybe it is not necessarily the proper final solution...)
i.e.
----8<----
Author: Cristian Marussi <[email protected]> Date: Fri Oct 21 17:24:04 2022 +0100
hwmon: Add new .get_sensor_id hwops
Add a new optional helper which can be defined to allow an hwmon chip to provide the logic to map hwmon indexes to the real underlying sensor IDs.
drivers/hwmon/hwmon.c +1 -1
@@ -213,7 +213,8 @@ static void hwmon_thermal_remove_sensor(void *data)list_del (data); } -static int hwmon_thermal_add_sensor (struct device *dev,int index) +static int hwmon_thermal_add_sensor(struct device *dev, int index,
7+ unsigned int sensor_id)
{
struct hwmon_device *hwdev = to_hwmon_device(dev);
struct hwmon_thermal_data *tdata;
@@ -227,7 +228,7 @@ static int hwmon_thermal_add_sensor(struct device *dev, int index)
tdata->dev = dev;
tdata->index = index;- tzd = devm_thermal_of_zone_register(dev, index, tdata,
+ tzd = devm_thermal_of_zone_register(dev, sensor_id, tdata,
&hwmon_thermal_ops);
if (IS_ERR(tzd)) {
if (PTR_ERR(tzd) != -ENODEV)@@ -264,13 +265,18 @@ static int hwmon_thermal_register_sensors(struct device *dev)
for (j = 0; info[i]->config[j]; j++) {
int err;+ unsigned int id;
if (!(info[i]->config[j] & HWMON_T_INPUT) ||
!chip->ops->is_visible(drvdata, hwmon_temp,
hwmon_temp_input, j))
continue;- err = hwmon_thermal_add_sensor(dev, j);
+ id = !chip->ops->get_sensor_id ? j :
+ chip->ops->get_sensor_id(drvdata,
+ hwmon_temp, j);
+
+ err = hwmon_thermal_add_sensor(dev, j, id);
if (err)
return err;
}include/linux/hwmon.h +3 -0
@@ -396,6 +396,9 @@ enum hwmon_intrusion_attributes {struct hwmon_ops {umode_t (*is_visible)(const void *drvdata,enum hwmon_sensor_types type,u32 attr,int channel); +unsigned int (*get_sensor_id)(const void *drvdata, +enum hwmon_sensor_types type, +int channel);int (*read)(struct device *dev,enum hwmon_sensor_types type,u32 attr,int channel,long *val); int (*read_string)(struct device *dev, enum hwmon_sensor_types type,
----->8----
... plus obviously the related scmi-hwmon.c patch to make use of this.
Any thought ? Am I missing something ?
(not really an expert on both subsystems really ... :P)
Thanks,
Cristian
Guenter Roeck
maintainerQuoted 85 lines · Cristian Marussi
Hi,
Starting with v6.1-rc1 the SCMI HWMON driver failed probing on my JUNO due to the fact that no trip points were (ever !) defined in the DT; bisecting it looks like that after:
https://lore.kernel.org/all/[email protected]/
the presence of the mandatory trips node within thermal zones is now enforced.
So, this is NOT what this bug report is about (I'll post soon patches for the JUNO DT missing trips) BUT once this problem was solved in the DT, another issue appeared:
[ 1.921929] hwmon hwmon0: temp2_input not attached to any thermal zonethat despite having now a goodi/valid DT describing 2 sensors and 2 thermal zones embedding that sensors, only the first one is found as belonging to one ThermZ. (this happens ALSO with v6.0 once I added the trips...)
Digging deep into this, it turned out that inside the call chain
devm_hwmon_device_register_with_info
hwmon_device_register_with_info__hwmon_device_register hwmon_thermal_register_sensors(dev) --> hwmon_thermal_add_sensor(dev, j) --> devm_thermal_of_zone_register(dev, sensor_id, tdata, )the HWMON channel index j is passed to the Thermal framework in order to search and bind sensors with defined thermal zone, but this lead to the assumption that sequential HWMON channel indexes corresponds one-to-one to the underlying real sensor IDs that the ThermalFramework uses for matching within the DT.
On a system like my SCMI-based DT where I have 2 temp-sensors bound to 2 thermal zones like:
thernal_zones { pmic { ... thermal-sensors = <&scmi_sensors0 0>; ... trips { ... } soc { ... thermal-sensors = <&scmi_sensors0 3>; ... trips { ... } } }This works fine by chance for the pmic (j=0, sensor_id=0) BUT cannot work for the soc where J=1 BUT the real sensor ID is 3.
Note that there can be a number of sensors, not all of them of a type handled by HWMON, and enumerated by SCMI in different ways depending on the platform.
I suppose this is not an SCMI-only related issue, but maybe in non-SCMI context, where sensors are purely defined in the DT, the solution can be more easily attained (i.e. renumber the sensors).
At first I tried to solve this inside
scmi-hwmon.cBUT I could not find a way to present to the HWMON subsystem the list of sensors preserving the above index/sensor_id matching (not even with a hack like passing down dummy sensors to the HWMON subsystem to fill the 'holes' in the numbering)My tentative solution, which works fine for me in my context, was to add an optional HWMON hwops, so that the core hwmon can retrieve if needed the real sensor ID if different from the channel index (using an optional hwops instead of some static hwinfo var let me avoid to have to patch all the existent hwmon drivers that happens to just work fine as of today...but maybe it is not necessarily the proper final solution...)
i.e.
----8<----
Quoted 8 lines
Author: Cristian Marussi <[email protected]> Date: Fri Oct 21 17:24:04 2022 +0100hwmon: Add new .get_sensor_id hwops
Add a new optional helper which can be defined to allow an hwmon chip to provide the logic to map hwmon indexes to the real underlying sensor IDs.
Maybe I am missing something, but ...
The driver isn't supposed to know anything about thermal devices and thermal zones. If that no longer works, and drivers have to know about thermal zones and thermal zone device index values anyway, we might as well pull thermal device support from the hwmon core and implement it in drivers.
Guenter
Guenter Roeck
maintainerQuoted 93 lines · Guenter Roeck
Quoted 83 lines · Cristian Marussi
Hi,
Starting with v6.1-rc1 the SCMI HWMON driver failed probing on my JUNO due to the fact that no trip points were (ever !) defined in the DT; bisecting it looks like that after:
https://lore.kernel.org/all/[email protected]/
the presence of the mandatory trips node within thermal zones is now enforced.
So, this is NOT what this bug report is about (I'll post soon patches for the JUNO DT missing trips) BUT once this problem was solved in the DT, another issue appeared:
[ 1.921929] hwmon hwmon0:
temp2_inputnot attached to any thermal zonethat despite having now a goodi/valid DT describing 2 sensors and 2 thermal zones embedding that sensors, only the first one is found as belonging to one ThermZ. (this happens ALSO with v6.0 once I added the trips...)
Digging deep into this, it turned out that inside the call chain
devm_hwmon_device_register_with_infohwmon_device_register_with_info
__hwmon_device_registerhwmon_thermal_register_sensors(dev)
-->hwmon_thermal_add_sensor(dev, j)
-->devm_thermal_of_zone_register(dev, sensor_id, tdata, )the HWMON channel index j is passed to the Thermal framework in order to search and bind sensors with defined thermal zone, but this lead to the assumption that sequential HWMON channel indexes corresponds one-to-one to the underlying real sensor IDs that the ThermalFramework uses for matching within the DT.
On a system like my SCMI-based DT where I have 2 temp-sensors bound to 2 thermal zones like:
thernal_zones{
pmic {
...
thermal-sensors = <&scmi_sensors00>;
...
trips {
...
}
soc {
...
thermal-sensors = <&scmi_sensors03>;
...
trips {
...
}
}
}This works fine by chance for the pmic (j=0, sensor_id=0) BUT cannot work for the soc where J=1 BUT the real sensor ID is 3.
Note that there can be a number of sensors, not all of them of a type handled by HWMON, and enumerated by SCMI in different ways depending on the platform.
I suppose this is not an SCMI-only related issue, but maybe in non-SCMI context, where sensors are purely defined in the DT, the solution can be more easily attained (i.e. renumber the sensors).
At first I tried to solve this inside
scmi-hwmon.cBUT I could not find a way to present to the HWMON subsystem the list of sensors preserving the above index/sensor_id matching (not even with a hack like passing down dummy sensors to the HWMON subsystem to fill the 'holes' in the numbering)My tentative solution, which works fine for me in my context, was to add an optional HWMON hwops, so that the core hwmon can retrieve if needed the real sensor ID if different from the channel index (using an optional hwops instead of some static hwinfo var let me avoid to have to patch all the existent hwmon drivers that happens to just work fine as of today...but maybe it is not necessarily the proper final solution...)
i.e.
Quoted 8 lines
----8<----
Author: Cristian Marussi <[email protected]> Date: Fri Oct 21 17:24:04 2022 +0100
hwmon: Add new .get_sensor_id hwops
Add a new optional helper which can be defined to allow an hwmon chip to provide the logic to map hwmon indexes to the real underlying sensor IDs.
Quoted 8 lines
Maybe I am missing something, but ...
The driver isn't supposed to know anything about thermal devices and thermal zones. If that no longer works, and drivers have to know about thermal zones and thermal zone device index values anyway, we might as well pull thermal device support from the hwmon core and implement it in drivers.
No, wait: The question is really: Why does the scmi driver present the sensor with index 3 to the hwmon subsystem as sensor with index 1 ?
If the sensor has index 3, and is presented to other entities as sensor with index 3, it should be presented to the hwmon subsystem as sensor with index 3, not with index 1. If sensors with index 1..2 do not exist, the is_visible function should return 0 for those sensors.
Guenter
Quoted 2 lines
Guenter
Quoted 103 lines · Guenter Roeck
Quoted 93 lines · Guenter Roeck
Quoted 83 lines · Cristian Marussi
Hi,
Starting with v6.1-rc1 the SCMI HWMON driver failed probing on my JUNO due to the fact that no trip points were (ever !) defined in the DT; bisecting it looks like that after:
https://lore.kernel.org/all/[email protected]/
the presence of the mandatory trips node within thermal zones is now enforced.
So, this is NOT what this bug report is about (I'll post soon patches for the JUNO DT missing trips) BUT once this problem was solved in the DT, another issue appeared:
[ 1.921929] hwmon hwmon0:
temp2_inputnot attached to any thermal zonethat despite having now a goodi/valid DT describing 2 sensors and 2 thermal zones embedding that sensors, only the first one is found as belonging to one ThermZ. (this happens ALSO with v6.0 once I added the trips...)
Digging deep into this, it turned out that inside the call chain
devm_hwmon_device_register_with_infohwmon_device_register_with_info
__hwmon_device_registerhwmon_thermal_register_sensors(dev)
-->hwmon_thermal_add_sensor(dev, j)
-->devm_thermal_of_zone_register(dev, sensor_id, tdata, )the HWMON channel index j is passed to the Thermal framework in order to search and bind sensors with defined thermal zone, but this lead to the assumption that sequential HWMON channel indexes corresponds one-to-one to the underlying real sensor IDs that the ThermalFramework uses for matching within the DT.
On a system like my SCMI-based DT where I have 2 temp-sensors bound to 2 thermal zones like:
thernal_zones{
pmic {
...
thermal-sensors = <&scmi_sensors00>;
...
trips {
...
}
soc {
...
thermal-sensors = <&scmi_sensors03>;
...
trips {
...
}
}
}This works fine by chance for the pmic (j=0, sensor_id=0) BUT cannot work for the soc where J=1 BUT the real sensor ID is 3.
Note that there can be a number of sensors, not all of them of a type handled by HWMON, and enumerated by SCMI in different ways depending on the platform.
I suppose this is not an SCMI-only related issue, but maybe in non-SCMI context, where sensors are purely defined in the DT, the solution can be more easily attained (i.e. renumber the sensors).
At first I tried to solve this inside
scmi-hwmon.cBUT I could not find a way to present to the HWMON subsystem the list of sensors preserving the above index/sensor_id matching (not even with a hack like passing down dummy sensors to the HWMON subsystem to fill the 'holes' in the numbering)My tentative solution, which works fine for me in my context, was to add an optional HWMON hwops, so that the core hwmon can retrieve if needed the real sensor ID if different from the channel index (using an optional hwops instead of some static hwinfo var let me avoid to have to patch all the existent hwmon drivers that happens to just work fine as of today...but maybe it is not necessarily the proper final solution...)
i.e.
Quoted 8 lines
----8<----
Author: Cristian Marussi <[email protected]> Date: Fri Oct 21 17:24:04 2022 +0100
hwmon: Add new .get_sensor_id hwops
Add a new optional helper which can be defined to allow an hwmon chip to provide the logic to map hwmon indexes to the real underlying sensor IDs.Quoted 8 lines
Maybe I am missing something, but ...
The driver isn't supposed to know anything about thermal devices and thermal zones. If that no longer works, and drivers have to know about thermal zones and thermal zone device index values anyway, we might as well pull thermal device support from the hwmon core and implement it in drivers.
Quoted 8 lines
No, wait: The question is really: Why does the scmi driver present the sensor with index 3 to the hwmon subsystem as sensor with index 1 ?
If the sensor has index 3, and is presented to other entities as sensor with index 3, it should be presented to the hwmon subsystem as sensor with index 3, not with index 1. If sensors with index 1..2 do not exist, the
is_visiblefunction should return 0 for those sensors.
My understanding was that the hwmon index is the index of the channel and hwmon_channel_info struct groups channels by type while the index is really used as a pointer in the hwmon_channel_info.config field, so in this case you're saying I should present 4 temp sensors placing a 'hole' at sensor 1,2 making is_visible return 0 for those channels ?
Basically keeping the channel indexes in sync with the real sensor ID by the means of some dummy sensor entries in the config field: this could result potentially in a lot of holes given in SCMI the sensor_id is 16 bits and I thought that was too hackish but I can try.
In the meantime, I gave it a go at what you suggested early (if I got it right...) by removing from the scmi-hwmon driver the HWMON_C_REGISTER_TZ attribute and adding a few explicit calls to devm_thermal_of_zone_register() at the end of the probe to specifically register the needed temp sensors (and associated real sensor IDs) with the ThermalFramework without relying on the HWMON core for Thermal and it works fine indeed.
Thanks,
Cristian
Guenter Roeck
maintainerQuoted 119 lines · Cristian Marussi
Quoted 103 lines · Guenter Roeck
Quoted 93 lines · Guenter Roeck
Quoted 83 lines · Cristian Marussi
Hi,
Starting with v6.1-rc1 the SCMI HWMON driver failed probing on my JUNO due to the fact that no trip points were (ever !) defined in the DT; bisecting it looks like that after:
https://lore.kernel.org/all/[email protected]/
the presence of the mandatory trips node within thermal zones is now enforced.
So, this is NOT what this bug report is about (I'll post soon patches for the JUNO DT missing trips) BUT once this problem was solved in the DT, another issue appeared:
[ 1.921929] hwmon hwmon0:
temp2_inputnot attached to any thermal zonethat despite having now a goodi/valid DT describing 2 sensors and 2 thermal zones embedding that sensors, only the first one is found as belonging to one ThermZ. (this happens ALSO with v6.0 once I added the trips...)
Digging deep into this, it turned out that inside the call chain
devm_hwmon_device_register_with_info
hwmon_device_register_with_info
__hwmon_device_registerhwmon_thermal_register_sensors(dev)
-->hwmon_thermal_add_sensor(dev, j)
-->devm_thermal_of_zone_register(dev, sensor_id, tdata, )the HWMON channel index j is passed to the Thermal framework in order to search and bind sensors with defined thermal zone, but this lead to the assumption that sequential HWMON channel indexes corresponds one-to-one to the underlying real sensor IDs that the ThermalFramework uses for matching within the DT.
On a system like my SCMI-based DT where I have 2 temp-sensors bound to 2 thermal zones like:
thernal_zones{
pmic {
...
thermal-sensors = <&scmi_sensors00>;
...
trips {
...
}
soc {
...
thermal-sensors = <&scmi_sensors03>;
...
trips {
...
}
}
}This works fine by chance for the pmic (j=0, sensor_id=0) BUT cannot work for the soc where J=1 BUT the real sensor ID is 3.
Note that there can be a number of sensors, not all of them of a type handled by HWMON, and enumerated by SCMI in different ways depending on the platform.
I suppose this is not an SCMI-only related issue, but maybe in non-SCMI context, where sensors are purely defined in the DT, the solution can be more easily attained (i.e. renumber the sensors).
At first I tried to solve this inside
scmi-hwmon.cBUT I could not find a way to present to the HWMON subsystem the list of sensors preserving the above index/sensor_id matching (not even with a hack like passing down dummy sensors to the HWMON subsystem to fill the 'holes' in the numbering)My tentative solution, which works fine for me in my context, was to add an optional HWMON hwops, so that the core hwmon can retrieve if needed the real sensor ID if different from the channel index (using an optional hwops instead of some static hwinfo var let me avoid to have to patch all the existent hwmon drivers that happens to just work fine as of today...but maybe it is not necessarily the proper final solution...)
i.e.
Quoted 8 lines
----8<----
Author: Cristian Marussi <[email protected]> Date: Fri Oct 21 17:24:04 2022 +0100
hwmon: Add new .get_sensor_id hwops
Add a new optional helper which can be defined to allow an hwmon chip to provide the logic to map hwmon indexes to the real underlying sensor IDs.Quoted 8 lines
Maybe I am missing something, but ...
The driver isn't supposed to know anything about thermal devices and thermal zones. If that no longer works, and drivers have to know about thermal zones and thermal zone device index values anyway, we might as well pull thermal device support from the hwmon core and implement it in drivers.
Quoted 8 lines
No, wait: The question is really: Why does the scmi driver present the sensor with index 3 to the hwmon subsystem as sensor with index 1 ?
If the sensor has index 3, and is presented to other entities as sensor with index 3, it should be presented to the hwmon subsystem as sensor with index 3, not with index 1. If sensors with index 1..2 do not exist, the
is_visiblefunction should return 0 for those sensors.My understanding was that the hwmon index is the index of the channel and
hwmon_channel_infostruct groups channels by type while the index is really used as a pointer in the hwmon_channel_info.config field, so in this case you're saying I should present 4 temp sensors placing a 'hole' at sensor 1,2 makingis_visiblereturn 0 for those channels ?
Quoted 5 lines
Basically keeping the channel indexes in sync with the real sensor ID by the means of some dummy sensor entries in the config field: this could result potentially in a lot of holes given in SCMI the
sensor_idis 16 bits and I thought that was too hackish but I can try.
The underlying idea with the hwmon -> thermal bridge is that index values used by thermal and by the hwmon subsystem match and, yes, that there would if necessary be holes in hwmon index values (normally this is not a 16-bit number space). If that doesn't work for scmi, and if there could indeed be something like
thermal-sensors = <&scmi_sensors0 12345>;
then I think the solution is indeed to not rely on the hwmon->thermal bridge in the hwmon core for this driver.
Quoted 7 lines
In the meantime, I gave it a go at what you suggested early (if I got it right...) by removing from the scmi-hwmon driver the
HWMON_C_REGISTER_TZattribute and adding a few explicit calls todevm_thermal_of_zone_register()at the end of the probe to specifically register the needed temp sensors (and associated real sensor IDs) with the ThermalFramework without relying on the HWMON core for Thermal and it works fine indeed.
Excellent.
Thanks,
Guenter
Quoted 132 lines · Guenter Roeck
Quoted 119 lines · Cristian Marussi
Quoted 103 lines · Guenter Roeck
Quoted 93 lines · Guenter Roeck
Quoted 83 lines · Cristian Marussi
Hi,
Starting with v6.1-rc1 the SCMI HWMON driver failed probing on my JUNO due to the fact that no trip points were (ever !) defined in the DT; bisecting it looks like that after:
https://lore.kernel.org/all/[email protected]/
the presence of the mandatory trips node within thermal zones is now enforced.
So, this is NOT what this bug report is about (I'll post soon patches for the JUNO DT missing trips) BUT once this problem was solved in the DT, another issue appeared:
[ 1.921929] hwmon hwmon0:
temp2_inputnot attached to any thermal zonethat despite having now a goodi/valid DT describing 2 sensors and 2 thermal zones embedding that sensors, only the first one is found as belonging to one ThermZ. (this happens ALSO with v6.0 once I added the trips...)
Digging deep into this, it turned out that inside the call chain
devm_hwmon_device_register_with_info
hwmon_device_register_with_info
__hwmon_device_registerhwmon_thermal_register_sensors(dev)
-->hwmon_thermal_add_sensor(dev, j)
-->devm_thermal_of_zone_register(dev, sensor_id, tdata, )the HWMON channel index j is passed to the Thermal framework in order to search and bind sensors with defined thermal zone, but this lead to the assumption that sequential HWMON channel indexes corresponds one-to-one to the underlying real sensor IDs that the ThermalFramework uses for matching within the DT.
On a system like my SCMI-based DT where I have 2 temp-sensors bound to 2 thermal zones like:
thernal_zones{
pmic {
...
thermal-sensors = <&scmi_sensors00>;
...
trips {
...
}
soc {
...
thermal-sensors = <&scmi_sensors03>;
...
trips {
...
}
}
}This works fine by chance for the pmic (j=0, sensor_id=0) BUT cannot work for the soc where J=1 BUT the real sensor ID is 3.
Note that there can be a number of sensors, not all of them of a type handled by HWMON, and enumerated by SCMI in different ways depending on the platform.
I suppose this is not an SCMI-only related issue, but maybe in non-SCMI context, where sensors are purely defined in the DT, the solution can be more easily attained (i.e. renumber the sensors).
At first I tried to solve this inside
scmi-hwmon.cBUT I could not find a way to present to the HWMON subsystem the list of sensors preserving the above index/sensor_id matching (not even with a hack like passing down dummy sensors to the HWMON subsystem to fill the 'holes' in the numbering)My tentative solution, which works fine for me in my context, was to add an optional HWMON hwops, so that the core hwmon can retrieve if needed the real sensor ID if different from the channel index (using an optional hwops instead of some static hwinfo var let me avoid to have to patch all the existent hwmon drivers that happens to just work fine as of today...but maybe it is not necessarily the proper final solution...)
i.e.
Quoted 8 lines
----8<----
Author: Cristian Marussi <[email protected]> Date: Fri Oct 21 17:24:04 2022 +0100
hwmon: Add new .get_sensor_id hwops
Add a new optional helper which can be defined to allow an hwmon chip to provide the logic to map hwmon indexes to the real underlying sensor IDs.Quoted 8 lines
Maybe I am missing something, but ...
The driver isn't supposed to know anything about thermal devices and thermal zones. If that no longer works, and drivers have to know about thermal zones and thermal zone device index values anyway, we might as well pull thermal device support from the hwmon core and implement it in drivers.
Quoted 8 lines
No, wait: The question is really: Why does the scmi driver present the sensor with index 3 to the hwmon subsystem as sensor with index 1 ?
If the sensor has index 3, and is presented to other entities as sensor with index 3, it should be presented to the hwmon subsystem as sensor with index 3, not with index 1. If sensors with index 1..2 do not exist, the
is_visiblefunction should return 0 for those sensors.My understanding was that the hwmon index is the index of the channel and
hwmon_channel_infostruct groups channels by type while the index is really used as a pointer in the hwmon_channel_info.config field, so in this case you're saying I should present 4 temp sensors placing a 'hole' at sensor 1,2 makingis_visiblereturn 0 for those channels ?Quoted 5 lines
Basically keeping the channel indexes in sync with the real sensor ID by the means of some dummy sensor entries in the config field: this could result potentially in a lot of holes given in SCMI the
sensor_idis 16 bits and I thought that was too hackish but I can try.The underlying idea with the hwmon -> thermal bridge is that index values used by thermal and by the hwmon subsystem match and, yes, that there would if necessary be holes in hwmon index values (normally this is not a 16-bit number space). If that doesn't work for scmi, and if there could indeed be something like
Quoted 4 lines
thermal-sensors = <&scmi_sensors0 12345>;then I think the solution is indeed to not rely on the
hwmon->thermalbridge in the hwmon core for this driver.
Even though implausible it could be possible to have an SCMI fw platform advertising such high sensor IDs.
Quoted 11 lines
Quoted 8 lines
In the meantime, I gave it a go at what you suggested early (if I got it right...) by removing from the scmi-hwmon driver the
HWMON_C_REGISTER_TZattribute and adding a few explicit calls todevm_thermal_of_zone_register()at the end of the probe to specifically register the needed temp sensors (and associated real sensor IDs) with the ThermalFramework without relying on the HWMON core for Thermal and it works fine indeed.Excellent.
I'll follow this path.
Thanks for your help & feedback.
Cristian
Re: (bug report) HWMON & Thermal interactions #forregzbot
In reply to Cristian Marussi[Note: this mail is primarily send for documentation purposes and/or for regzbot, my Linux kernel regression tracking bot. That's why I removed most or all folks from the list of recipients, but left any that looked like a mailing lists. These mails usually contain '#forregzbot' in the subject, to make them easy to spot and filter out.]
[TLDR: I'm adding this regression report to the list of tracked regressions; all text from me you find below is based on a few templates paragraphs you might have encountered already already in similar form.]
Hi, this is your Linux kernel regression tracker. CCing the regression mailing list, as it should be in the loop for all regressions, as explained here:
https://www.kernel.org/doc/html/latest/admin-guide/reporting-issues.html
Quoted 4 lines · Cristian Marussi
Starting with v6.1-rc1 the SCMI HWMON driver failed probing on my JUNO due to the fact that no trip points were (ever !) defined in the DT; bisecting it looks like that after:
Thanks for the report. To be sure below issue doesn't fall through the cracks unnoticed, I'm adding it to regzbot, my Linux kernel regression tracking bot:
#regzbot ^introduced e51813313
#regzbot title SCMI HWMON driver failed probing on JUNO #regzbot ignore-activity
This isn't a regression? This issue or a fix for it are already discussed somewhere else? It was fixed already? You want to clarify when the regression started to happen? Or point out I got the title or something else totally wrong? Then just reply -- ideally with also telling regzbot about it, as explained here:
https://linux-regtracking.leemhuis.info/tracked-regression/
Reminder for developers: When fixing the issue, add 'Link:' tags pointing to the report (the mail this one replies to), as explained for in the Linux kernel's documentation; above webpage explains why this is important for tracked regressions.
Ciao, Thorsten (wearing his 'the Linux kernel's regression tracker' hat)
P.S.: As the Linux kernel's regression tracker I deal with a lot of reports and sometimes miss something important when writing mails like this. If that's the case here, don't hesitate to tell me in a public reply, it's in everyone's interest to set the public record straight.
Quoted 159 lines
https://lore.kernel.org/all/[email protected]/
the presence of the mandatory trips node within thermal zones is now enforced.
So, this is NOT what this bug report is about (I'll post soon patches for the JUNO DT missing trips) BUT once this problem was solved in the DT, another issue appeared:
[ 1.921929] hwmon hwmon0: temp2_input not attached to any thermal zonethat despite having now a goodi/valid DT describing 2 sensors and 2 thermal zones embedding that sensors, only the first one is found as belonging to one ThermZ. (this happens ALSO with v6.0 once I added the trips...)
Digging deep into this, it turned out that inside the call chain
devm_hwmon_device_register_with_info
hwmon_device_register_with_info__hwmon_device_register hwmon_thermal_register_sensors(dev) --> hwmon_thermal_add_sensor(dev, j) --> devm_thermal_of_zone_register(dev, sensor_id, tdata, )the HWMON channel index j is passed to the Thermal framework in order to search and bind sensors with defined thermal zone, but this lead to the assumption that sequential HWMON channel indexes corresponds one-to-one to the underlying real sensor IDs that the ThermalFramework uses for matching within the DT.
On a system like my SCMI-based DT where I have 2 temp-sensors bound to 2 thermal zones like:
thernal_zones { pmic { ... thermal-sensors = <&scmi_sensors0 0>; ... trips { ... } soc { ... thermal-sensors = <&scmi_sensors0 3>; ... trips { ... } } }This works fine by chance for the pmic (j=0, sensor_id=0) BUT cannot work for the soc where J=1 BUT the real sensor ID is 3.
Note that there can be a number of sensors, not all of them of a type handled by HWMON, and enumerated by SCMI in different ways depending on the platform.
I suppose this is not an SCMI-only related issue, but maybe in non-SCMI context, where sensors are purely defined in the DT, the solution can be more easily attained (i.e. renumber the sensors).
At first I tried to solve this inside
scmi-hwmon.cBUT I could not find a way to present to the HWMON subsystem the list of sensors preserving the above index/sensor_id matching (not even with a hack like passing down dummy sensors to the HWMON subsystem to fill the 'holes' in the numbering)My tentative solution, which works fine for me in my context, was to add an optional HWMON hwops, so that the core hwmon can retrieve if needed the real sensor ID if different from the channel index (using an optional hwops instead of some static hwinfo var let me avoid to have to patch all the existent hwmon drivers that happens to just work fine as of today...but maybe it is not necessarily the proper final solution...)
i.e.
----8<----
Author: Cristian Marussi <[email protected]> Date: Fri Oct 21 17:24:04 2022 +0100hwmon: Add new .get_sensor_id hwops
Add a new optional helper which can be defined to allow an hwmon chip to provide the logic to map hwmon indexes to the real underlying sensor IDs.
Signed-off-by Cristian Marussi <[email protected]>drivers/hwmon/hwmon.c +8
-3@@ -213,7 +213,8 @@ static void hwmon_thermal_remove_sensor(void *data)list_del (data); } -static int hwmon_thermal_add_sensor(struct device *dev, int index) +static int hwmon_thermal_add_sensor (struct device *dev,int index, 7+ unsigned int sensor_id) {struct hwmon_device *hwdev =to_hwmon_device (dev);struct hwmon_thermal_data *tdata;@@ -227,7 +228,7 @@ static int hwmon_thermal_add_sensor(struct device *dev, int index) tdata->dev = dev; tdata->index = index; - tzd =devm_thermal_of_zone_register (dev, index, tdata, + tzd =devm_thermal_of_zone_register (dev, sensor_id, tdata, &hwmon_thermal_ops);if (IS_ERR (tzd)) {if (PTR_ERR (tzd) != -ENODEV )@@ -264,13 +265,18 @@ static int hwmon_thermal_register_sensors(struct device *dev)for (j =0 ; info[i]->config[j]; j++) {int err; +unsigned int id;if (!(info[i]->config[j] &HWMON_T_INPUT ) || !chip->ops->is_visible (drvdata, hwmon_temp, hwmon_temp_input, j))continue ; - err =hwmon_thermal_add_sensor (dev, j); + id = !chip->ops->get_sensor_id ? j : + chip->ops->get_sensor_id (drvdata, + hwmon_temp, j); + + err =hwmon_thermal_add_sensor (dev, j, id);if (err)return err; }include/linux/hwmon.h +3
-1@@ -396,6 +396,9 @@ enum hwmon_intrusion_attributes {struct hwmon_ops {umode_t (*is_visible)(const void *drvdata,enum hwmon_sensor_types type,u32 attr,int channel); +unsigned int (*get_sensor_id)(const void *drvdata, +enum hwmon_sensor_types type, +int channel);int (*read)(struct device *dev,enum hwmon_sensor_types type,u32 attr,int channel,long *val); int (*read_string)(struct device *dev, enum hwmon_sensor_types type, ----->8----... plus obviously the related
scmi-hwmon.cpatch to make use of this.Any thought ? Am I missing something ?
(not really an expert on both subsystems really ... :P)Thanks,
Cristian
Re: (bug report) HWMON & Thermal interactions #forregzbot
Quoted 6 lines · Thorsten Leemhuis
Quoted 4 lines · Cristian Marussi
Starting with v6.1-rc1 the SCMI HWMON driver failed probing on my JUNO due to the fact that no trip points were (ever !) defined in the DT; bisecting it looks like that after:
Quoted 7 lines
Thanks for the report. To be sure below issue doesn't fall through the cracks unnoticed, I'm adding it to regzbot, my Linux kernel regression tracking bot:
#regzbot ^introduced
e51813313
#regzbot title SCMI HWMON driver failed probing on JUNO #regzbot ignore-activity
#regzbot fixed-by: c4a7b9b587ca