Skip to contentSkip to conversation

staging:iio:sca3000 extract old event handling and move to poll for events from buffer

bug report Dan Carpenter 3 participants 4 messages May 28, 2021 – Jun 4, 2021 IIO

lore
Share & tools
lore
#0 lore raw

Hello Jonathan Cameron,

The patch 25888dc51163: "staging:iio:sca3000 extract old event handling and move to poll for events from buffer" from May 18, 2011, leads to the following static checker warning:

	drivers/iio/accel/sca3000.c:734 sca3000_read_raw()
	warn: no-op. '((*val) << 19) >> 19'

drivers/iio/accel/sca3000.c
709 static int sca3000_read_raw(struct iio_dev *indio_dev,

   710                              struct iio_chan_spec const *chan,
   711                              int *val,
   712                              int *val2,
   713                              long mask)
   714  {
   715          struct sca3000_state *st = iio_priv(indio_dev);
   716          int ret;
   717          u8 address;
   718  
   719          switch (mask) {
   720          case IIO_CHAN_INFO_RAW:
   721                  mutex_lock(&st->lock);
   722                  if (chan->type == IIO_ACCEL) {
   723                          if (st->mo_det_use_count) {
   724                                  mutex_unlock(&st->lock);
   725                                  return -EBUSY;
   726                          }
   727                          address = sca3000_addresses[chan->address][0];
   728                          ret = sca3000_read_data_short(st, address, 2);
   729                          if (ret < 0) {
   730                                  mutex_unlock(&st->lock);
   731                                  return ret;
   732                          }
   733                          *val = (be16_to_cpup((__be16 *)st->rx) >> 3) & 0x1FFF;
   734                          *val = ((*val) << (sizeof(*val) * 8 - 13)) >>
                                                  ^^^^^^^^^^^^^^^^^^^^^^^
   735                                  (sizeof(*val) * 8 - 13);
                                        ^^^^^^^^^^^^^^^^^^^^^^^

This code works, but it relies on undefined behavior of left shift overflow and it's very unsatisfying. Pretty sure there is a UBSan warning for this at runtime.

   736                  } else {
   737                          /* get the temperature when available */
   738                          ret = sca3000_read_data_short(st,
   739                                                        SCA3000_REG_TEMP_MSB_ADDR,
   740                                                        2);
   741                          if (ret < 0) {
   742                                  mutex_unlock(&st->lock);
   743                                  return ret;
   744                          }
   745                          *val = ((st->rx[0] & 0x3F) << 3) |
   746                                 ((st->rx[1] & 0xE0) >> 5);
   747                  }
   748                  mutex_unlock(&st->lock);
   749                  return IIO_VAL_INT;

regards,
dan carpenter

maintainer
#1 lore raw
Quoted 40 lines · On Fri, 28 May 2021 15:00:52 +0300 Dan Carpenter <[email protected]>…

Hello Jonathan Cameron,

The patch 25888dc51163: "staging:iio:sca3000 extract old event handling and move to poll for events from buffer" from May 18, 2011, leads to the following static checker warning:

	drivers/iio/accel/sca3000.c:734 sca3000_read_raw()
	warn: no-op. '((*val) << 19) >> 19'

drivers/iio/accel/sca3000.c
709 static int sca3000_read_raw(struct iio_dev *indio_dev,

   710                              struct iio_chan_spec const *chan,
   711                              int *val,
   712                              int *val2,
   713                              long mask)
   714  {
   715          struct sca3000_state *st = iio_priv(indio_dev);
   716          int ret;
   717          u8 address;
   718  
   719          switch (mask) {
   720          case IIO_CHAN_INFO_RAW:
   721                  mutex_lock(&st->lock);
   722                  if (chan->type == IIO_ACCEL) {
   723                          if (st->mo_det_use_count) {
   724                                  mutex_unlock(&st->lock);
   725                                  return -EBUSY;
   726                          }
   727                          address = sca3000_addresses[chan->address][0];
   728                          ret = sca3000_read_data_short(st, address, 2);
   729                          if (ret < 0) {
   730                                  mutex_unlock(&st->lock);
   731                                  return ret;
   732                          }
   733                          *val = (be16_to_cpup((__be16 *)st->rx) >> 3) & 0x1FFF;
   734                          *val = ((*val) << (sizeof(*val) * 8 - 13)) >>
                                                  ^^^^^^^^^^^^^^^^^^^^^^^
   735                                  (sizeof(*val) * 8 - 13);
                                        ^^^^^^^^^^^^^^^^^^^^^^^
Quoted 3 lines

This code works, but it relies on undefined behavior of left shift overflow and it's very unsatisfying. Pretty sure there is a UBSan warning for this at runtime.

Thanks Dan. Looks like a slightly odd variant on open coded sign_extend32() Should be fine to replace with

*val = sign_extend32(*val, 13);

What can I say, I wrote this a long time ago when I was young and stupid :)

Anyhow, I'll roll a patch to do that shortly.

Jonathan

Quoted 18 lines
   736                  } else {
   737                          /* get the temperature when available */
   738                          ret = sca3000_read_data_short(st,
   739                                                        SCA3000_REG_TEMP_MSB_ADDR,
   740                                                        2);
   741                          if (ret < 0) {
   742                                  mutex_unlock(&st->lock);
   743                                  return ret;
   744                          }
   745                          *val = ((st->rx[0] & 0x3F) << 3) |
   746                                 ((st->rx[1] & 0xE0) >> 5);
   747                  }
   748                  mutex_unlock(&st->lock);
   749                  return IIO_VAL_INT;

regards,
dan carpenter

#2 lore raw
Quoted 47 lines · Jonathan Cameron
Quoted 40 lines · On Fri, 28 May 2021 15:00:52 +0300 Dan Carpenter <[email protected]>…

Hello Jonathan Cameron,

The patch 25888dc51163: "staging:iio:sca3000 extract old event handling and move to poll for events from buffer" from May 18, 2011, leads to the following static checker warning:

	drivers/iio/accel/sca3000.c:734 sca3000_read_raw()
	warn: no-op. '((*val) << 19) >> 19'

drivers/iio/accel/sca3000.c
709 static int sca3000_read_raw(struct iio_dev *indio_dev,

   710                              struct iio_chan_spec const *chan,
   711                              int *val,
   712                              int *val2,
   713                              long mask)
   714  {
   715          struct sca3000_state *st = iio_priv(indio_dev);
   716          int ret;
   717          u8 address;
   718  
   719          switch (mask) {
   720          case IIO_CHAN_INFO_RAW:
   721                  mutex_lock(&st->lock);
   722                  if (chan->type == IIO_ACCEL) {
   723                          if (st->mo_det_use_count) {
   724                                  mutex_unlock(&st->lock);
   725                                  return -EBUSY;
   726                          }
   727                          address = sca3000_addresses[chan->address][0];
   728                          ret = sca3000_read_data_short(st, address, 2);
   729                          if (ret < 0) {
   730                                  mutex_unlock(&st->lock);
   731                                  return ret;
   732                          }
   733                          *val = (be16_to_cpup((__be16 *)st->rx) >> 3) & 0x1FFF;
   734                          *val = ((*val) << (sizeof(*val) * 8 - 13)) >>
                                                  ^^^^^^^^^^^^^^^^^^^^^^^
   735                                  (sizeof(*val) * 8 - 13);
                                        ^^^^^^^^^^^^^^^^^^^^^^^
Quoted 3 lines

This code works, but it relies on undefined behavior of left shift overflow and it's very unsatisfying. Pretty sure there is a UBSan warning for this at runtime.

Quoted 6 lines

Thanks Dan. Looks like a slightly odd variant on open coded sign_extend32() Should be fine to replace with

*val = sign_extend32(*val, 13);

What can I say, I wrote this a long time ago when I was young and stupid :)

I didn't think of sign_extend32()... I was forced to look at some of my 2009 code the other day and it was *so* bad. :P

regards,
dan carpenter

#3 lore raw
In reply to Jonathan Cameron
Quoted 2 lines · Jonathan Cameron

On Fri, 28 May 2021 15:00:52 +0300
Dan Carpenter <[email protected]> wrote:

...

Quoted 6 lines
Quoted 6 lines
   733                          *val = (be16_to_cpup((__be16 *)st->rx) >> 3) & 0x1FFF;
   734                          *val = ((*val) << (sizeof(*val) * 8 - 13)) >>
                                                  ^^^^^^^^^^^^^^^^^^^^^^^
   735                                  (sizeof(*val) * 8 - 13);
                                        ^^^^^^^^^^^^^^^^^^^^^^^
Quoted 8 lines
Quoted 3 lines

This code works, but it relies on undefined behavior of left shift overflow and it's very unsatisfying. Pretty sure there is a UBSan warning for this at runtime.

Thanks Dan. Looks like a slightly odd variant on open coded sign_extend32() Should be fine to replace with

*val = sign_extend32(*val, 13);

Oh, indeed.

Signature · 2 lines
With Best Regards,
Andy Shevchenko