net: dsa: ocelot: phylink updates
Subsystems (4)
cover net: dsa: ocelot: phylink updates
Hi,
This series updates the Ocelot DSA driver for some of the recent phylink changes. Specifically, we fill in the supported_interfaces fields, convert to mac_select_pcs and mark the driver as non-legacy. We do not convert to phylink_generic_validate() as Ocelot has special support for its rate adapting PCS which makes the generic validate method unsuitable for this driver.
The three changes mentioned above are implemented in their own separate patches with one additional cleanup:
1) Populate the supported_interfaces bitmap
2) Remove the now unnecessary interface checks in the validate methods
3) Convert from phylink_set_pcs() to .mac_select_pcs.
4) Mark the driver as non-legacy
Thanks.
RFC -> non-RFC: add reviewed-by/tested-by's, update patch 1 to set the supported_interfaces bitmap in felix.c rather than the sub-drivers as requested by Vladimir.
drivers/net/dsa/ocelot/felix.c | 30 ++++++++++++++++++++++++------ drivers/net/dsa/ocelot/felix_vsc9959.c | 7 ------- drivers/net/dsa/ocelot/seville_vsc9953.c | 7 ------- 3 files changed, 24 insertions(+), 20 deletions(-)
Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!
PATCH 1/4 net: dsa: ocelot: populate supported_interfaces
Populate the supported interfaces bitmap for the Ocelot DSA switches.
Since all sub-drivers only support a single interface mode, defined by ocelot_port->phy_mode, we can handle this in the main driver code without reference to the sub-driver.
--- drivers/net/dsa/ocelot/felix.c | 10 ++++++++++ 1 file changed, 10 insertions(+)
drivers/net/dsa/ocelot/felix.c +10 -0
@@ -778,6 +778,15 @@ static int felix_vlan_del(struct dsa_switch *ds, int port,return ocelot_vlan_del (ocelot, port, vlan->vid); } +static void felix_phylink_get_caps (struct dsa_switch *ds,int port, +struct phylink_config *config) +{ +struct ocelot *ocelot = ds->priv; + +__set_bit (ocelot->ports[port].phy_mode, + config->supported_interfaces); +} +static void felix_phylink_validate (struct dsa_switch *ds,int port,unsigned long *supported,struct phylink_link_state *state)
@@ -1587,6 +1596,7 @@ const struct dsa_switch_ops felix_switch_ops = { .get_ethtool_stats = felix_get_ethtool_stats, .get_sset_count = felix_get_sset_count, .get_ts_info = felix_get_ts_info, + .phylink_get_caps = felix_phylink_get_caps, .phylink_validate = felix_phylink_validate, .phylink_mac_config = felix_phylink_mac_config, .phylink_mac_link_down = felix_phylink_mac_link_down,
Signature · 1 line
2.30.2
PATCH 2/4 net: dsa: ocelot: remove interface checks
In reply to Russell King (Oracle)When the supported interfaces bitmap is populated, phylink will itself check that the interface mode is present in this bitmap. Drivers no longer need to perform this check themselves. Remove these checks.
--- drivers/net/dsa/ocelot/felix_vsc9959.c | 7 ------- drivers/net/dsa/ocelot/seville_vsc9953.c | 7 ------- 2 files changed, 14 deletions(-)
drivers/net/dsa/ocelot/felix_vsc9959.c +0 -7
@@ -944,15 +944,8 @@ static void vsc9959_phylink_validate(struct ocelot *ocelot, int port,unsigned long *supported, struct phylink_link_state *state) { - struct ocelot_port *ocelot_port = ocelot->ports[port];__ETHTOOL_DECLARE_LINK_MODE_MASK (mask ) = {0 , }; -if (state->interface !=PHY_INTERFACE_MODE_NA && - state->interface != ocelot_port->phy_mode) { -linkmode_zero (supported); -return ; - } -phylink_set_port_modes (mask);phylink_set (mask, Autoneg);phylink_set (mask, Pause);
drivers/net/dsa/ocelot/seville_vsc9953.c +0 -7
@@ -917,15 +917,8 @@ static void vsc9953_phylink_validate(struct ocelot *ocelot, int port,unsigned long *supported, struct phylink_link_state *state) { - struct ocelot_port *ocelot_port = ocelot->ports[port];__ETHTOOL_DECLARE_LINK_MODE_MASK (mask ) = {0 , }; -if (state->interface !=PHY_INTERFACE_MODE_NA && - state->interface != ocelot_port->phy_mode) { -linkmode_zero (supported); -return ; - } -phylink_set_port_modes (mask);phylink_set (mask, Autoneg);phylink_set (mask, Pause);
Signature · 1 line
2.30.2
PATCH 3/4 net: dsa: ocelot: convert to mac_select_pcs()
In reply to Russell King (Oracle)Convert the PCS selection to use mac_select_pcs, which allows the PCS to perform any validation it needs, and removes the need to set the PCS in the mac_config() callback, delving into the higher DSA levels to do so.
--- drivers/net/dsa/ocelot/felix.c | 14 ++++++++------ 1 file changed, 8 insertions(+), 6 deletions(-)
drivers/net/dsa/ocelot/felix.c +8 -6
@@ -798,16 +798,18 @@ static void felix_phylink_validate(struct dsa_switch *ds, int port, felix->info->phylink_validate (ocelot, port, supported, state); } -static void felix_phylink_mac_config (struct dsa_switch *ds,int port, -unsigned int link_an_mode, -const struct phylink_link_state *state) +static struct phylink_pcs *felix_phylink_mac_select_pcs (struct dsa_switch *ds, +int port, +phy_interface_t iface) {struct ocelot *ocelot = ds->priv;struct felix *felix =ocelot_to_felix (ocelot); -struct dsa_port *dp =dsa_to_port (ds, port); +struct phylink_pcs *pcs =NULL ;if (felix->pcs && felix->pcs[port]) -phylink_set_pcs (dp->pl, felix->pcs[port]); + pcs = felix->pcs[port]; + +return pcs; } static void felix_phylink_mac_link_down(struct dsa_switch *ds, int port,
@@ -1598,7 +1600,7 @@ const struct dsa_switch_ops felix_switch_ops = { .get_ts_info = felix_get_ts_info, .phylink_get_caps = felix_phylink_get_caps, .phylink_validate = felix_phylink_validate, - .phylink_mac_config = felix_phylink_mac_config, + .phylink_mac_select_pcs = felix_phylink_mac_select_pcs, .phylink_mac_link_down = felix_phylink_mac_link_down, .phylink_mac_link_up = felix_phylink_mac_link_up, .port_fast_age = felix_port_fast_age,
Signature · 1 line
2.30.2
PATCH 4/4 net: dsa: ocelot: mark as non-legacy
In reply to Russell King (Oracle)The ocelot DSA driver does not make use of the speed, duplex, pause or advertisement in its phylink_mac_config() implementation, so it can be marked as a non-legacy driver.
--- drivers/net/dsa/ocelot/felix.c | 6 ++++++ 1 file changed, 6 insertions(+)
drivers/net/dsa/ocelot/felix.c +6 -0
@@ -783,6 +783,12 @@ static void felix_phylink_get_caps(struct dsa_switch *ds, int port, {struct ocelot *ocelot = ds->priv; +/* This driver does not make use of the speed, duplex, pause or the +* advertisement in its mac_config, so it is safe to mark this driver +* as non-legacy. +*/ + config->legacy_pre_march2020 = false; +__set_bit (ocelot->ports[port].phy_mode, config->supported_interfaces); }
Signature · 1 line
2.30.2
Re: [PATCH net-next 1/4] net: dsa: ocelot: populate supported_interfaces
In reply to Russell King (Oracle)Quoted 16 lines · Russell King (Oracle)
Populate the supported interfaces bitmap for the Ocelot DSA switches.
Since all sub-drivers only support a single interface mode, defined by
ocelot_port->phy_mode, we can handle this in the main driver code without reference to the sub-driver.Signed-off-by Russell King (Oracle) <[email protected]>--- drivers/net/dsa/ocelot/felix.c | 10 ++++++++++ 1 file changed, 10 insertions(+)drivers/net/dsa/ocelot/felix.c +0
-0
drivers/net/dsa/ocelot/felix.c static int felix_vlan_del(struct dsa_switch *ds, int port, · line 786
Quoted 9 lines
drivers/net/dsa/ocelot/felix.c +6
-0@@ -778,6 +778,15 @@ static int felix_vlan_del(struct dsa_switch *ds, int port,return ocelot_vlan_del (ocelot, port, vlan->vid); } +static void felix_phylink_get_caps (struct dsa_switch *ds,int port, +struct phylink_config *config) +{ +struct ocelot *ocelot = ds->priv; + + __set_bit(ocelot->ports[port].phy_mode,
Sorry, this should be ->phy_mode.
Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!