Skip to contentSkip to conversation

mtk_eth_soc phylink updates

RFC PATCH In review Russell King (Oracle) 2 participants 14 messages Apr 6, 2022 – Apr 11, 2022

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

cover mtk_eth_soc phylink updates

Hi,

This series ultimately updates mtk_eth_soc to use phylink_pcs, with some fixes along the way.

Previous attempts to update this driver (which is now marked as legacy) have failed due to lack of testing. I am hoping that this time will be different; Marek can test RGMII modes, but not SGMII. So all that we know is that this patch series probably doesn't break RGMII.

1) remove unused mac_mode and sgmii flags members from structures.
2) remove unnecessary interpretation of speed when configuring 1000 and 2500 Base-X
3) move configuration of SGMII duplex setting from mac_config() to link_up()
4) only pass in interface mode to mtk_sgmii_setup_mode_force()
5) move decision about which mtk_sgmii_setup_mode_*() function to call into mtk_sgmii.c
6) add a fixme comment for RGMII explaning why the call to mtk_gmac0_rgmii_adjust() is completely wrong - this needs to be addressed by someone who has the hardware and can test an appropriate fix. This fixme means that the driver still can't become non-legacy.
7) move gmac setup from mac_config() to mac_finish() - this preserves the order that we write to the hardware when we eventually convert to phylink_pcs()
8) move configuration of syscfg0 in SGMII/802.3z mode to mac_finish() for the same reasons as (7).
9) convert mtk_sgmii.c code structure and the mtk_sgmii structure to suit conversion to phylink_pcs
10) finally convert to phylink_pcs

It would be nice to get these changes fully tested, but past experience has shown that for this driver, that's unfortunately very unlikely. So, I propose that the merging plan for this is that if there are no comments after three weeks to a month, I'll send this for inclusion in net-next.

 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 103 +++++++++-------
 drivers/net/ethernet/mediatek/mtk_eth_soc.h |  40 +++----
 drivers/net/ethernet/mediatek/mtk_sgmii.c   | 174 ++++++++++++++++------------
 3 files changed, 185 insertions(+), 132 deletions(-)
Signature · 7 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!

_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
#1 lore raw

RFC PATCH 1/12 net: mtk_eth_soc: remove unused mac->mode

mac->mode is only ever written to in one location, and is thus superflous. Remove it.

---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 1 -
 drivers/net/ethernet/mediatek/mtk_eth_soc.h | 1 -
 2 files changed, 2 deletions(-)
drivers/net/ethernet/mediatek/mtk_eth_soc.c +0 -1
index f02d07ec5ccb..e491d43f049a 100644
@@ -2968,7 +2968,6 @@ static int mtk_add_mac(struct mtk_eth *eth, struct device_node *np)
 
 	/* mac config is not set */
 	mac->interface = PHY_INTERFACE_MODE_NA;
-	mac->mode = MLO_AN_PHY;
 	mac->speed = SPEED_UNKNOWN;
 
 	mac->phylink_config.dev = &eth->netdev[id]->dev;
drivers/net/ethernet/mediatek/mtk_eth_soc.h +0 -1
index c9d42be314b5..2b690f8a5391 100644
@@ -989,7 +989,6 @@ struct mtk_eth {
 struct mtk_mac {
 	int				id;
 	phy_interface_t			interface;
-	unsigned int			mode;
 	int				speed;
 	struct device_node		*of_node;
 	struct phylink			*phylink;
Signature · 7 lines
2.30.2


_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
#2 lore raw

RFC PATCH 2/12 net: mtk_eth_soc: remove unused sgmii flags

In reply to Russell King (Oracle)

The "flags" member of struct mtk_sgmii appears to be unused, as are the MTK_SGMII_PHYSPEED_* and MTK_HAS_FLAGS() macros. Remove them.

---
 drivers/net/ethernet/mediatek/mtk_eth_soc.h | 8 --------
 1 file changed, 8 deletions(-)
drivers/net/ethernet/mediatek/mtk_eth_soc.h +0 -8
index 2b690f8a5391..8a10761adda0 100644
@@ -859,23 +859,15 @@ struct mtk_soc_data {
 /* currently no SoC has more than 2 macs */
 #define MTK_MAX_DEVS			2
 
-#define MTK_SGMII_PHYSPEED_AN          BIT(31)
-#define MTK_SGMII_PHYSPEED_MASK        GENMASK(2, 0)
-#define MTK_SGMII_PHYSPEED_1000        BIT(0)
-#define MTK_SGMII_PHYSPEED_2500        BIT(1)
-#define MTK_HAS_FLAGS(flags, _x)       (((flags) & (_x)) == (_x))
-
 /* struct mtk_sgmii -  This is the structure holding sgmii regmap and its
  *                     characteristics
  * @regmap:            The register map pointing at the range used to setup
  *                     SGMII modes
- * @flags:             The enum refers to which mode the sgmii wants to run on
  * @ana_rgc3:          The offset refers to register ANA_RGC3 related to regmap
  */
 
 struct mtk_sgmii {
 	struct regmap   *regmap[MTK_MAX_DEVS];
-	u32             flags[MTK_MAX_DEVS];
 	u32             ana_rgc3;
 };
 
Signature · 7 lines
2.30.2


_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
#3 lore raw

RFC PATCH 3/12 net: mtk_eth_soc: add mask and update PCS speed definitions

In reply to Russell King (Oracle)

The PCS speed setting is a two bit field, but it is defined as two separate bits. Add a bitfield mask for the speed definitions, an
use the FIELD_PREP() macro to define each PCS speed.

---
 drivers/net/ethernet/mediatek/mtk_eth_soc.h | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)
drivers/net/ethernet/mediatek/mtk_eth_soc.h +5 -3
index 8a10761adda0..f31ef594008a 100644
@@ -17,6 +17,7 @@
 #include <linux/phylink.h>
 #include <linux/rhashtable.h>
 #include <linux/dim.h>
+#include <linux/bitfield.h>
 #include "mtk_ppe.h"
 
 #define MTK_QDMA_PAGE_SIZE	2048
@@ -485,9 +486,10 @@
 #define SGMSYS_SGMII_MODE		0x20
 #define SGMII_IF_MODE_BIT0		BIT(0)
 #define SGMII_SPEED_DUPLEX_AN		BIT(1)
-#define SGMII_SPEED_10			0x0
-#define SGMII_SPEED_100			BIT(2)
-#define SGMII_SPEED_1000		BIT(3)
+#define SGMII_SPEED_MASK		GENMASK(3, 2)
+#define SGMII_SPEED_10			FIELD_PREP(SGMII_SPEED_MASK, 0)
+#define SGMII_SPEED_100			FIELD_PREP(SGMII_SPEED_MASK, 1)
+#define SGMII_SPEED_1000		FIELD_PREP(SGMII_SPEED_MASK, 2)
 #define SGMII_DUPLEX_FULL		BIT(4)
 #define SGMII_IF_MODE_BIT5		BIT(5)
 #define SGMII_REMOTE_FAULT_DIS		BIT(8)
Signature · 7 lines
2.30.2


_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
#4 lore raw

RFC PATCH 4/12 net: mtk_eth_soc: correct 802.3z speed setting

In reply to Russell King (Oracle)

Phylink does not guarantee that state->speed will be set correctly in the mac_config() call, so it's a bug that the driver makes use of it. Moreover, it is making use of it in a function that is only ever called for 1000BASE-X and 2500BASE-X which operate at a fixed speed which happens to be the same setting irrespective of the interface mode. We can simply remove the switch statement and just set the SGMII interface speed.

---
 drivers/net/ethernet/mediatek/mtk_sgmii.c | 18 +++++-------------
 1 file changed, 5 insertions(+), 13 deletions(-)
drivers/net/ethernet/mediatek/mtk_sgmii.c +5 -13
index 32d83421226a..16e66c0cb557 100644
@@ -33,6 +33,7 @@ int mtk_sgmii_init(struct mtk_sgmii *ss, struct device_node *r, u32 ana_rgc3)
 	return 0;
 }
 
+/* For SGMII interface mode */
 int mtk_sgmii_setup_mode_an(struct mtk_sgmii *ss, int id)
 {
 	unsigned int val;
@@ -59,6 +60,9 @@ int mtk_sgmii_setup_mode_an(struct mtk_sgmii *ss, int id)
 	return 0;
 }
 
+/* For 1000BASE-X and 2500BASE-X interface modes, which operate at a
+ * fixed speed.
+ */
 int mtk_sgmii_setup_mode_force(struct mtk_sgmii *ss, int id,
 			       const struct phylink_link_state *state)
 {
@@ -81,19 +85,7 @@ int mtk_sgmii_setup_mode_force(struct mtk_sgmii *ss, int id,
 	/* SGMII force mode setting */
 	regmap_read(ss->regmap[id], SGMSYS_SGMII_MODE, &val);
 	val &= ~SGMII_IF_MODE_MASK;
-
-	switch (state->speed) {
-	case SPEED_10:
-		val |= SGMII_SPEED_10;
-		break;
-	case SPEED_100:
-		val |= SGMII_SPEED_100;
-		break;
-	case SPEED_2500:
-	case SPEED_1000:
-		val |= SGMII_SPEED_1000;
-		break;
-	}
+	val |= SGMII_SPEED_1000;
 
 	if (state->duplex == DUPLEX_FULL)
 		val |= SGMII_DUPLEX_FULL;
Signature · 7 lines
2.30.2


_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
#5 lore raw

RFC PATCH 5/12 net: mtk_eth_soc: correct 802.3z duplex setting

In reply to Russell King (Oracle)

Phylink does not guarantee that state->duplex will be set correctly in the mac_config() call, so it's a bug that the driver makes use of it.

Move the 802.3z PCS duplex configuration to mac_link_up().

---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 16 +++++++++++----
 drivers/net/ethernet/mediatek/mtk_eth_soc.h |  1 +
 drivers/net/ethernet/mediatek/mtk_sgmii.c   | 22 +++++++++++++++------
 3 files changed, 29 insertions(+), 10 deletions(-)
drivers/net/ethernet/mediatek/mtk_eth_soc.c +12 -4
index e491d43f049a..6fedfa8fceb1 100644
@@ -482,8 +482,18 @@ static void mtk_mac_link_up(struct phylink_config *config,
 {
 	struct mtk_mac *mac = container_of(config, struct mtk_mac,
 					   phylink_config);
-	u32 mcr = mtk_r32(mac->hw, MTK_MAC_MCR(mac->id));
+	u32 mcr;
+
+	if (phy_interface_mode_is_8023z(interface)) {
+		struct mtk_eth *eth = mac->hw;
+
+		/* Decide how GMAC and SGMIISYS be mapped */
+		int sid = (MTK_HAS_CAPS(eth->soc->caps, MTK_SHARED_SGMII)) ?
+			   0 : mac->id;
+		mtk_sgmii_link_up(eth->sgmii, sid, speed, duplex);
+	}
 
+	mcr = mtk_r32(mac->hw, MTK_MAC_MCR(mac->id));
 	mcr &= ~(MAC_MCR_SPEED_100 | MAC_MCR_SPEED_1000 |
 		 MAC_MCR_FORCE_DPX | MAC_MCR_FORCE_TX_FC |
 		 MAC_MCR_FORCE_RX_FC);
@@ -2972,9 +2982,7 @@ static int mtk_add_mac(struct mtk_eth *eth, struct device_node *np)
 
 	mac->phylink_config.dev = &eth->netdev[id]->dev;
 	mac->phylink_config.type = PHYLINK_NETDEV;
-	/* This driver makes use of state->speed/state->duplex in
-	 * mac_config
-	 */
+	/* This driver makes use of state->speed in mac_config */
 	mac->phylink_config.legacy_pre_march2020 = true;
 	mac->phylink_config.mac_capabilities = MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
 		MAC_10 | MAC_100 | MAC_1000 | MAC_2500FD;
drivers/net/ethernet/mediatek/mtk_eth_soc.h +1 -0
index f31ef594008a..1912f84922c8 100644
@@ -1007,6 +1007,7 @@ int mtk_sgmii_init(struct mtk_sgmii *ss, struct device_node *np,
 int mtk_sgmii_setup_mode_an(struct mtk_sgmii *ss, int id);
 int mtk_sgmii_setup_mode_force(struct mtk_sgmii *ss, int id,
 			       const struct phylink_link_state *state);
+void mtk_sgmii_link_up(struct mtk_sgmii *ss, int id, int speed, int duplex);
 void mtk_sgmii_restart_an(struct mtk_eth *eth, int mac_id);
 
 int mtk_gmac_sgmii_path_setup(struct mtk_eth *eth, int mac_id);
drivers/net/ethernet/mediatek/mtk_sgmii.c +16 -6
index 16e66c0cb557..a5ec61e13b85 100644
@@ -82,14 +82,10 @@ int mtk_sgmii_setup_mode_force(struct mtk_sgmii *ss, int id,
 	val &= ~SGMII_AN_ENABLE;
 	regmap_write(ss->regmap[id], SGMSYS_PCS_CONTROL_1, val);
 
-	/* SGMII force mode setting */
+	/* Set the speed etc but leave the duplex unchanged */
 	regmap_read(ss->regmap[id], SGMSYS_SGMII_MODE, &val);
-	val &= ~SGMII_IF_MODE_MASK;
+	val &= SGMII_DUPLEX_FULL | ~SGMII_IF_MODE_MASK;
 	val |= SGMII_SPEED_1000;
-
-	if (state->duplex == DUPLEX_FULL)
-		val |= SGMII_DUPLEX_FULL;
-
 	regmap_write(ss->regmap[id], SGMSYS_SGMII_MODE, val);
 
 	/* Release PHYA power down state */
@@ -100,6 +96,20 @@ int mtk_sgmii_setup_mode_force(struct mtk_sgmii *ss, int id,
 	return 0;
 }
 
+/* For 1000BASE-X and 2500BASE-X interface modes */
+void mtk_sgmii_link_up(struct mtk_sgmii *ss, int id, int speed, int duplex)
+{
+	unsigned int val;
+
+	/* SGMII force duplex setting */
+	regmap_read(ss->regmap[id], SGMSYS_SGMII_MODE, &val);
+	val &= ~SGMII_DUPLEX_FULL;
+	if (duplex == DUPLEX_FULL)
+		val |= SGMII_DUPLEX_FULL;
+
+	regmap_write(ss->regmap[id], SGMSYS_SGMII_MODE, val);
+}
+
 void mtk_sgmii_restart_an(struct mtk_eth *eth, int mac_id)
 {
 	struct mtk_sgmii *ss = eth->sgmii;
Signature · 7 lines
2.30.2


_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
#6 lore raw

RFC PATCH 6/12 net: mtk_eth_soc: stop passing phylink state to sgmii setup

In reply to Russell King (Oracle)

Now that mtk_sgmii_setup_mode_force() only uses the interface mode from the phylink state, pass just the interface mode into this function.

---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 2 +-
 drivers/net/ethernet/mediatek/mtk_eth_soc.h | 2 +-
 drivers/net/ethernet/mediatek/mtk_sgmii.c   | 4 ++--
 3 files changed, 4 insertions(+), 4 deletions(-)
drivers/net/ethernet/mediatek/mtk_eth_soc.c +1 -1
index 6fedfa8fceb1..7f29256b4b3c 100644
@@ -387,7 +387,7 @@ static void mtk_mac_config(struct phylink_config *config, unsigned int mode,
 		/* Setup SGMIISYS with the determined property */
 		if (state->interface != PHY_INTERFACE_MODE_SGMII)
 			err = mtk_sgmii_setup_mode_force(eth->sgmii, sid,
-							 state);
+							 state->interface);
 		else if (phylink_autoneg_inband(mode))
 			err = mtk_sgmii_setup_mode_an(eth->sgmii, sid);
 
drivers/net/ethernet/mediatek/mtk_eth_soc.h +1 -1
index 1912f84922c8..93f150bb09dd 100644
@@ -1006,7 +1006,7 @@ int mtk_sgmii_init(struct mtk_sgmii *ss, struct device_node *np,
 		   u32 ana_rgc3);
 int mtk_sgmii_setup_mode_an(struct mtk_sgmii *ss, int id);
 int mtk_sgmii_setup_mode_force(struct mtk_sgmii *ss, int id,
-			       const struct phylink_link_state *state);
+			       phy_interface_t interface);
 void mtk_sgmii_link_up(struct mtk_sgmii *ss, int id, int speed, int duplex);
 void mtk_sgmii_restart_an(struct mtk_eth *eth, int mac_id);
 
drivers/net/ethernet/mediatek/mtk_sgmii.c +2 -2
index a5ec61e13b85..b656c8b3ca35 100644
@@ -64,7 +64,7 @@ int mtk_sgmii_setup_mode_an(struct mtk_sgmii *ss, int id)
  * fixed speed.
  */
 int mtk_sgmii_setup_mode_force(struct mtk_sgmii *ss, int id,
-			       const struct phylink_link_state *state)
+			       phy_interface_t interface)
 {
 	unsigned int val;
 
@@ -73,7 +73,7 @@ int mtk_sgmii_setup_mode_force(struct mtk_sgmii *ss, int id,
 
 	regmap_read(ss->regmap[id], ss->ana_rgc3, &val);
 	val &= ~RG_PHY_SPEED_MASK;
-	if (state->interface == PHY_INTERFACE_MODE_2500BASEX)
+	if (interface == PHY_INTERFACE_MODE_2500BASEX)
 		val |= RG_PHY_SPEED_3_125G;
 	regmap_write(ss->regmap[id], ss->ana_rgc3, val);
 
Signature · 7 lines
2.30.2


_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
#7 lore raw

RFC PATCH 7/12 net: mtk_eth_soc: provide mtk_sgmii_config()

In reply to Russell King (Oracle)

Provide mtk_sgmii_config() to wrap up the decisions about which SGMII configuration will be called.

---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c |  7 +------
 drivers/net/ethernet/mediatek/mtk_eth_soc.h |  5 ++---
 drivers/net/ethernet/mediatek/mtk_sgmii.c   | 20 +++++++++++++++++---
 3 files changed, 20 insertions(+), 12 deletions(-)
drivers/net/ethernet/mediatek/mtk_eth_soc.c +1 -6
index 7f29256b4b3c..a16f02ed921a 100644
@@ -385,12 +385,7 @@ static void mtk_mac_config(struct phylink_config *config, unsigned int mode,
 		       0 : mac->id;
 
 		/* Setup SGMIISYS with the determined property */
-		if (state->interface != PHY_INTERFACE_MODE_SGMII)
-			err = mtk_sgmii_setup_mode_force(eth->sgmii, sid,
-							 state->interface);
-		else if (phylink_autoneg_inband(mode))
-			err = mtk_sgmii_setup_mode_an(eth->sgmii, sid);
-
+		err = mtk_sgmii_config(eth->sgmii, sid, mode, state->interface);
 		if (err)
 			goto init_err;
 
drivers/net/ethernet/mediatek/mtk_eth_soc.h +2 -3
index 93f150bb09dd..4be779109cff 100644
@@ -1004,9 +1004,8 @@ u32 mtk_r32(struct mtk_eth *eth, unsigned reg);
 
 int mtk_sgmii_init(struct mtk_sgmii *ss, struct device_node *np,
 		   u32 ana_rgc3);
-int mtk_sgmii_setup_mode_an(struct mtk_sgmii *ss, int id);
-int mtk_sgmii_setup_mode_force(struct mtk_sgmii *ss, int id,
-			       phy_interface_t interface);
+int mtk_sgmii_config(struct mtk_sgmii *ss, int id, unsigned int mode,
+		     phy_interface_t interface);
 void mtk_sgmii_link_up(struct mtk_sgmii *ss, int id, int speed, int duplex);
 void mtk_sgmii_restart_an(struct mtk_eth *eth, int mac_id);
 
drivers/net/ethernet/mediatek/mtk_sgmii.c +17 -3
index b656c8b3ca35..57925910cf80 100644
@@ -34,7 +34,7 @@ int mtk_sgmii_init(struct mtk_sgmii *ss, struct device_node *r, u32 ana_rgc3)
 }
 
 /* For SGMII interface mode */
-int mtk_sgmii_setup_mode_an(struct mtk_sgmii *ss, int id)
+static int mtk_sgmii_setup_mode_an(struct mtk_sgmii *ss, int id)
 {
 	unsigned int val;
 
@@ -63,8 +63,8 @@ int mtk_sgmii_setup_mode_an(struct mtk_sgmii *ss, int id)
 /* For 1000BASE-X and 2500BASE-X interface modes, which operate at a
  * fixed speed.
  */
-int mtk_sgmii_setup_mode_force(struct mtk_sgmii *ss, int id,
-			       phy_interface_t interface)
+static int mtk_sgmii_setup_mode_force(struct mtk_sgmii *ss, int id,
+				      phy_interface_t interface)
 {
 	unsigned int val;
 
@@ -96,6 +96,20 @@ int mtk_sgmii_setup_mode_force(struct mtk_sgmii *ss, int id,
 	return 0;
 }
 
+int mtk_sgmii_config(struct mtk_sgmii *ss, int id, unsigned int mode,
+		     phy_interface_t interface)
+{
+	int err = 0;
+
+	/* Setup SGMIISYS with the determined property */
+	if (interface != PHY_INTERFACE_MODE_SGMII)
+		err = mtk_sgmii_setup_mode_force(ss, id, interface);
+	else if (phylink_autoneg_inband(mode))
+		err = mtk_sgmii_setup_mode_an(ss, id);
+
+	return err;
+}
+
 /* For 1000BASE-X and 2500BASE-X interface modes */
 void mtk_sgmii_link_up(struct mtk_sgmii *ss, int id, int speed, int duplex)
 {
Signature · 7 lines
2.30.2


_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
#8 lore raw

RFC PATCH 8/12 net: mtk_eth_soc: add fixme comment for state->speed use

In reply to Russell King (Oracle)

Add a fixme comment for the last remaining incorrect usage of state->speed in the mac_config() method, which is strangely in a code path which is only run when the PHY interface mode changes.

This means if we are in RGMII mode, changes in state->speed will not cause the INTF_MODE, TRGMII_RCK_CTRL and TRGMII_TCK_CTRL registers to be set according to the speed, nor will the TRGPLL clock be set to the correct value.

---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 8 ++++++++
 1 file changed, 8 insertions(+)
drivers/net/ethernet/mediatek/mtk_eth_soc.c +8 -0
index a16f02ed921a..b605a823dcd4 100644
@@ -324,6 +324,14 @@ static void mtk_mac_config(struct phylink_config *config, unsigned int mode,
 							      state->interface))
 					goto err_phy;
 			} else {
+				/* FIXME: this is incorrect. Not only does it
+				 * use state->speed (which is not guaranteed
+				 * to be correct) but it also makes use of it
+				 * in a code path that will only be reachable
+				 * when the PHY interface mode changes, not
+				 * when the speed changes. Consequently, RGMII
+				 * is probably broken.
+				 */
 				mtk_gmac0_rgmii_adjust(mac->hw,
 						       state->interface,
 						       state->speed);
Signature · 7 lines
2.30.2


_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
#9 lore raw

RFC PATCH 9/12 net: mtk_eth_soc: move MAC_MCR setting to mac_finish()

In reply to Russell King (Oracle)

Move the setting of the MTK_MAC_MCR register from the end of mac_config into the phylink mac_finish() method, to keep it as the very last write that is done during configuration.

---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 33 ++++++++++++++-------
 1 file changed, 22 insertions(+), 11 deletions(-)
drivers/net/ethernet/mediatek/mtk_eth_soc.c +22 -11
index b605a823dcd4..2ede1ccc538b 100644
@@ -266,8 +266,8 @@ static void mtk_mac_config(struct phylink_config *config, unsigned int mode,
 	struct mtk_mac *mac = container_of(config, struct mtk_mac,
 					   phylink_config);
 	struct mtk_eth *eth = mac->hw;
-	u32 mcr_cur, mcr_new, sid, i;
 	int val, ge_mode, err = 0;
+	u32 sid, i;
 
 	/* MT76x8 has no hardware settings between for the MAC */
 	if (!MTK_HAS_CAPS(eth->soc->caps, MTK_SOC_MT7628) &&
@@ -405,16 +405,6 @@ static void mtk_mac_config(struct phylink_config *config, unsigned int mode,
 		return;
 	}
 
-	/* Setup gmac */
-	mcr_cur = mtk_r32(mac->hw, MTK_MAC_MCR(mac->id));
-	mcr_new = mcr_cur;
-	mcr_new |= MAC_MCR_IPG_CFG | MAC_MCR_FORCE_MODE |
-		   MAC_MCR_BACKOFF_EN | MAC_MCR_BACKPR_EN | MAC_MCR_FORCE_LINK;
-
-	/* Only update control register when needed! */
-	if (mcr_new != mcr_cur)
-		mtk_w32(mac->hw, mcr_new, MTK_MAC_MCR(mac->id));
-
 	return;
 
 err_phy:
@@ -427,6 +417,26 @@ static void mtk_mac_config(struct phylink_config *config, unsigned int mode,
 		mac->id, phy_modes(state->interface), err);
 }
 
+static int mtk_mac_finish(struct phylink_config *config, unsigned int mode,
+			  phy_interface_t interface)
+{
+	struct mtk_mac *mac = container_of(config, struct mtk_mac,
+					   phylink_config);
+	u32 mcr_cur, mcr_new;
+
+	/* Setup gmac */
+	mcr_cur = mtk_r32(mac->hw, MTK_MAC_MCR(mac->id));
+	mcr_new = mcr_cur;
+	mcr_new |= MAC_MCR_IPG_CFG | MAC_MCR_FORCE_MODE |
+		   MAC_MCR_BACKOFF_EN | MAC_MCR_BACKPR_EN | MAC_MCR_FORCE_LINK;
+
+	/* Only update control register when needed! */
+	if (mcr_new != mcr_cur)
+		mtk_w32(mac->hw, mcr_new, MTK_MAC_MCR(mac->id));
+
+	return 0;
+}
+
 static void mtk_mac_pcs_get_state(struct phylink_config *config,
 				  struct phylink_link_state *state)
 {
@@ -531,6 +541,7 @@ static const struct phylink_mac_ops mtk_phylink_ops = {
 	.mac_pcs_get_state = mtk_mac_pcs_get_state,
 	.mac_an_restart = mtk_mac_an_restart,
 	.mac_config = mtk_mac_config,
+	.mac_finish = mtk_mac_finish,
 	.mac_link_down = mtk_mac_link_down,
 	.mac_link_up = mtk_mac_link_up,
 };
Signature · 7 lines
2.30.2


_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
#10 lore raw

RFC PATCH 10/12 net: mtk_eth_soc: move restoration of SYSCFG0 to mac_finish()

In reply to Russell King (Oracle)

The SGMIISYS configuration is performed while ETHSYS_SYSCFG0 is in a disabled state. In order to preserve this when we switch to phylink_pcs we need to move the restoration of this register to the mac_finish() callback.

---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 11 +++++++++--
 drivers/net/ethernet/mediatek/mtk_eth_soc.h |  1 +
 2 files changed, 10 insertions(+), 2 deletions(-)
drivers/net/ethernet/mediatek/mtk_eth_soc.c +9 -2
index 2ede1ccc538b..0db2341f399f 100644
@@ -397,8 +397,8 @@ static void mtk_mac_config(struct phylink_config *config, unsigned int mode,
 		if (err)
 			goto init_err;
 
-		regmap_update_bits(eth->ethsys, ETHSYS_SYSCFG0,
-				   SYSCFG0_SGMII_MASK, val);
+		/* Save the syscfg0 value for mac_finish */
+		mac->syscfg0 = val;
 	} else if (phylink_autoneg_inband(mode)) {
 		dev_err(eth->dev,
 			"In-band mode not supported in non SGMII mode!\n");
@@ -422,8 +422,15 @@ static int mtk_mac_finish(struct phylink_config *config, unsigned int mode,
 {
 	struct mtk_mac *mac = container_of(config, struct mtk_mac,
 					   phylink_config);
+	struct mtk_eth *eth = mac->hw;
 	u32 mcr_cur, mcr_new;
 
+	/* Enable SGMII */
+	if (interface == PHY_INTERFACE_MODE_SGMII ||
+	    phy_interface_mode_is_8023z(interface))
+		regmap_update_bits(eth->ethsys, ETHSYS_SYSCFG0,
+				   SYSCFG0_SGMII_MASK, mac->syscfg0);
+
 	/* Setup gmac */
 	mcr_cur = mtk_r32(mac->hw, MTK_MAC_MCR(mac->id));
 	mcr_new = mcr_cur;
drivers/net/ethernet/mediatek/mtk_eth_soc.h +1 -0
index 4be779109cff..96f90e9fb9dd 100644
@@ -991,6 +991,7 @@ struct mtk_mac {
 	struct mtk_hw_stats		*hw_stats;
 	__be32				hwlro_ip[MTK_MAX_LRO_IP_CNT];
 	int				hwlro_ip_cnt;
+	unsigned int			syscfg0;
 };
 
 /* the struct describing the SoC. these are declared in the soc_xyz.c files */
Signature · 7 lines
2.30.2


_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
#11 lore raw

RFC PATCH 11/12 net: mtk_eth_soc: convert code structure to suit split PCS support

In reply to Russell King (Oracle)

Provide a mtk_pcs structure which encapsulates everything that the PCS functions need (the regmap and ana_rgc3 offset), and use this in the PCS functions. Provide shim functions to convert from the existing "mtk_sgmii_*" interface to the converted PCS functions.

---
 drivers/net/ethernet/mediatek/mtk_eth_soc.h |  15 ++-
 drivers/net/ethernet/mediatek/mtk_sgmii.c   | 121 +++++++++++---------
 2 files changed, 78 insertions(+), 58 deletions(-)
drivers/net/ethernet/mediatek/mtk_eth_soc.h +11 -4
index 96f90e9fb9dd..7de860c9d2e3 100644
@@ -861,16 +861,23 @@ struct mtk_soc_data {
 /* currently no SoC has more than 2 macs */
 #define MTK_MAX_DEVS			2
 
-/* struct mtk_sgmii -  This is the structure holding sgmii regmap and its
- *                     characteristics
+/* struct mtk_pcs -    This structure holds each sgmii regmap and associated
+ *                     data
  * @regmap:            The register map pointing at the range used to setup
  *                     SGMII modes
  * @ana_rgc3:          The offset refers to register ANA_RGC3 related to regmap
  */
+struct mtk_pcs {
+	struct regmap	*regmap;
+	u32             ana_rgc3;
+};
 
+/* struct mtk_sgmii -  This is the structure holding sgmii regmap and its
+ *                     characteristics
+ * @pcs                Array of individual PCS structures
+ */
 struct mtk_sgmii {
-	struct regmap   *regmap[MTK_MAX_DEVS];
-	u32             ana_rgc3;
+	struct mtk_pcs	pcs[MTK_MAX_DEVS];
 };
 
 /* struct mtk_eth -	This is the main datasructure for holding the state
drivers/net/ethernet/mediatek/mtk_sgmii.c +67 -54

200 lines not on this page · raw message

Signature · 7 lines
2.30.2


_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
#12 lore raw

RFC PATCH 12/12 net: mtk_eth_soc: partially convert to phylink_pcs

In reply to Russell King (Oracle)

Partially convert mtk_eth_soc to phylink_pcs, moving the configuration, link up and AN restart over. However, it seems mac_pcs_get_state() doesn't actually get the state from the PCS, so we can't convert that over without a better understanding of the hardware.

---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 49 ++++++++----------
 drivers/net/ethernet/mediatek/mtk_eth_soc.h |  7 ++-
 drivers/net/ethernet/mediatek/mtk_sgmii.c   | 55 +++++++++++----------
 3 files changed, 53 insertions(+), 58 deletions(-)
drivers/net/ethernet/mediatek/mtk_eth_soc.c +21 -28
index 0db2341f399f..874fec43fb35 100644
@@ -260,6 +260,25 @@ static void mtk_gmac0_rgmii_adjust(struct mtk_eth *eth,
 	mtk_w32(eth, val, TRGMII_TCK_CTRL);
 }
 
+static struct phylink_pcs *mtk_mac_select_pcs(struct phylink_config *config,
+					      phy_interface_t interface)
+{
+	struct mtk_mac *mac = container_of(config, struct mtk_mac,
+					   phylink_config);
+	struct mtk_eth *eth = mac->hw;
+	unsigned int sid;
+
+	if (interface == PHY_INTERFACE_MODE_SGMII ||
+	    phy_interface_mode_is_8023z(interface)) {
+		sid = (MTK_HAS_CAPS(eth->soc->caps, MTK_SHARED_SGMII)) ?
+		       0 : mac->id;
+
+		return mtk_sgmii_select_pcs(eth->sgmii, sid);
+	}
+
+	return NULL;
+}
+
 static void mtk_mac_config(struct phylink_config *config, unsigned int mode,
 			   const struct phylink_link_state *state)
 {
@@ -267,7 +286,7 @@ static void mtk_mac_config(struct phylink_config *config, unsigned int mode,
 					   phylink_config);
 	struct mtk_eth *eth = mac->hw;
 	int val, ge_mode, err = 0;
-	u32 sid, i;
+	u32 i;
 
 	/* MT76x8 has no hardware settings between for the MAC */
 	if (!MTK_HAS_CAPS(eth->soc->caps, MTK_SOC_MT7628) &&
@@ -388,15 +407,6 @@ static void mtk_mac_config(struct phylink_config *config, unsigned int mode,
 				   SYSCFG0_SGMII_MASK,
 				   ~(u32)SYSCFG0_SGMII_MASK);
 
-		/* Decide how GMAC and SGMIISYS be mapped */
-		sid = (MTK_HAS_CAPS(eth->soc->caps, MTK_SHARED_SGMII)) ?
-		       0 : mac->id;
-
-		/* Setup SGMIISYS with the determined property */
-		err = mtk_sgmii_config(eth->sgmii, sid, mode, state->interface);
-		if (err)
-			goto init_err;
-
 		/* Save the syscfg0 value for mac_finish */
 		mac->syscfg0 = val;
 	} else if (phylink_autoneg_inband(mode)) {
@@ -476,14 +486,6 @@ static void mtk_mac_pcs_get_state(struct phylink_config *config,
 		state->pause |= MLO_PAUSE_TX;
 }
 
-static void mtk_mac_an_restart(struct phylink_config *config)
-{
-	struct mtk_mac *mac = container_of(config, struct mtk_mac,
-					   phylink_config);
-
-	mtk_sgmii_restart_an(mac->hw, mac->id);
-}
-
 static void mtk_mac_link_down(struct phylink_config *config, unsigned int mode,
 			      phy_interface_t interface)
 {
@@ -504,15 +506,6 @@ static void mtk_mac_link_up(struct phylink_config *config,
 					   phylink_config);
 	u32 mcr;
 
-	if (phy_interface_mode_is_8023z(interface)) {
-		struct mtk_eth *eth = mac->hw;
-
-		/* Decide how GMAC and SGMIISYS be mapped */
-		int sid = (MTK_HAS_CAPS(eth->soc->caps, MTK_SHARED_SGMII)) ?
-			   0 : mac->id;
-		mtk_sgmii_link_up(eth->sgmii, sid, speed, duplex);
-	}
-
 	mcr = mtk_r32(mac->hw, MTK_MAC_MCR(mac->id));
 	mcr &= ~(MAC_MCR_SPEED_100 | MAC_MCR_SPEED_1000 |
 		 MAC_MCR_FORCE_DPX | MAC_MCR_FORCE_TX_FC |
@@ -545,8 +538,8 @@ static void mtk_mac_link_up(struct phylink_config *config,
 
 static const struct phylink_mac_ops mtk_phylink_ops = {
 	.validate = phylink_generic_validate,
+	.mac_select_pcs = mtk_mac_select_pcs,
 	.mac_pcs_get_state = mtk_mac_pcs_get_state,
-	.mac_an_restart = mtk_mac_an_restart,
 	.mac_config = mtk_mac_config,
 	.mac_finish = mtk_mac_finish,
 	.mac_link_down = mtk_mac_link_down,
drivers/net/ethernet/mediatek/mtk_eth_soc.h +3 -4
index 7de860c9d2e3..209ab2a1433c 100644
@@ -866,10 +866,12 @@ struct mtk_soc_data {
  * @regmap:            The register map pointing at the range used to setup
  *                     SGMII modes
  * @ana_rgc3:          The offset refers to register ANA_RGC3 related to regmap
+ * @pcs:               Phylink PCS structure
  */
 struct mtk_pcs {
 	struct regmap	*regmap;
 	u32             ana_rgc3;
+	struct phylink_pcs pcs;
 };
 
 /* struct mtk_sgmii -  This is the structure holding sgmii regmap and its
@@ -1010,12 +1012,9 @@ void mtk_stats_update_mac(struct mtk_mac *mac);
 void mtk_w32(struct mtk_eth *eth, u32 val, unsigned reg);
 u32 mtk_r32(struct mtk_eth *eth, unsigned reg);
 
+struct phylink_pcs *mtk_sgmii_select_pcs(struct mtk_sgmii *ss, int id);
 int mtk_sgmii_init(struct mtk_sgmii *ss, struct device_node *np,
 		   u32 ana_rgc3);
-int mtk_sgmii_config(struct mtk_sgmii *ss, int id, unsigned int mode,
-		     phy_interface_t interface);
-void mtk_sgmii_link_up(struct mtk_sgmii *ss, int id, int speed, int duplex);
-void mtk_sgmii_restart_an(struct mtk_eth *eth, int mac_id);
 
 int mtk_gmac_sgmii_path_setup(struct mtk_eth *eth, int mac_id);
 int mtk_gmac_gephy_path_setup(struct mtk_eth *eth, int mac_id);
drivers/net/ethernet/mediatek/mtk_sgmii.c +29 -26

113 lines not on this page · raw message

Signature · 7 lines
2.30.2


_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
#13 lore raw
In reply to Russell King (Oracle)

A gentle reminder to those who either worked on or who look after this driver to test this series and report back please.

Thanks.

Quoted 46 lines · Russell King (Oracle)

Hi,

This series ultimately updates mtk_eth_soc to use phylink_pcs, with some fixes along the way.

Previous attempts to update this driver (which is now marked as legacy) have failed due to lack of testing. I am hoping that this time will be different; Marek can test RGMII modes, but not SGMII. So all that we know is that this patch series probably doesn't break RGMII.

1) remove unused mac_mode and sgmii flags members from structures.
2) remove unnecessary interpretation of speed when configuring 1000 and 2500 Base-X
3) move configuration of SGMII duplex setting from mac_config() to link_up()
4) only pass in interface mode to mtk_sgmii_setup_mode_force()
5) move decision about which mtk_sgmii_setup_mode_*() function to call into mtk_sgmii.c
6) add a fixme comment for RGMII explaning why the call to mtk_gmac0_rgmii_adjust() is completely wrong - this needs to be addressed by someone who has the hardware and can test an appropriate fix. This fixme means that the driver still can't become non-legacy.
7) move gmac setup from mac_config() to mac_finish() - this preserves the order that we write to the hardware when we eventually convert to phylink_pcs()
8) move configuration of syscfg0 in SGMII/802.3z mode to mac_finish() for the same reasons as (7).
9) convert mtk_sgmii.c code structure and the mtk_sgmii structure to suit conversion to phylink_pcs
10) finally convert to phylink_pcs

It would be nice to get these changes fully tested, but past experience has shown that for this driver, that's unfortunately very unlikely. So, I propose that the merging plan for this is that if there are no comments after three weeks to a month, I'll send this for inclusion in net-next.

 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 103 +++++++++-------
 drivers/net/ethernet/mediatek/mtk_eth_soc.h |  40 +++----
 drivers/net/ethernet/mediatek/mtk_sgmii.c   | 174 ++++++++++++++++------------
 3 files changed, 185 insertions(+), 132 deletions(-)
Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!
Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!