Skip to contentSkip to conversation

Various mtk_eth_soc cleanups

PATCH Applied Russell King (Oracle) 3 participants 6 messages Mar 7, 2023 – Mar 9, 2023

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

cover Various mtk_eth_soc cleanups

Here are a number of patches that do a bit of cleanup to mtk_eth_soc.

The first patch cleans up mtk_gmac0_rgmii_adjust(), which is the troublesome function preventing the driver becoming a post-March2020 phylink driver. It doesn't solve that problem, merely makes the code easier to follow by getting rid of repeated tenary operators.

The second patch moves the check for DDR2 memory to the initialisation of phylink's supported_interfaces - if TRGMII is not possible for some reason, we should not be erroring out in phylink MAC operations when that can be determined prior to phylink creation.

The third patch removes checks from mtk_mac_config() that are done when initialising supported_interfaces - phylink will not call mtk_mac_config() with an interface that was not marked as supported, so these checks are redundant.

The last patch removes the remaining vestiges of REVMII and RMII support, which appears to be entirely unused.

These shouldn't conflict with Daniel's patch set, but if they do I will rework as appropriate.

Thanks.

 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 81 ++++++++++++-----------------
 1 file changed, 33 insertions(+), 48 deletions(-)
Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!
#1 lore raw

PATCH 1/4 net: mtk_eth_soc: tidy mtk_gmac0_rgmii_adjust()

Get rid of the multiple tenary operators in mtk_gmac0_rgmii_adjust() replacing them with a single if(), thus making the code easier to read.

---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 34 ++++++++++++---------
 1 file changed, 19 insertions(+), 15 deletions(-)
drivers/net/ethernet/mediatek/mtk_eth_soc.c +19 -15
index 14be6ea51b88..c63f17929ccf 100644
@@ -397,38 +397,42 @@ static int mt7621_gmac0_rgmii_adjust(struct mtk_eth *eth,
 static void mtk_gmac0_rgmii_adjust(struct mtk_eth *eth,
 				   phy_interface_t interface, int speed)
 {
-	u32 val;
+	unsigned long rate;
+	u32 tck, rck, intf;
 	int ret;
 
 	if (interface == PHY_INTERFACE_MODE_TRGMII) {
 		mtk_w32(eth, TRGMII_MODE, INTF_MODE);
-		val = 500000000;
-		ret = clk_set_rate(eth->clks[MTK_CLK_TRGPLL], val);
+		ret = clk_set_rate(eth->clks[MTK_CLK_TRGPLL], 500000000);
 		if (ret)
 			dev_err(eth->dev, "Failed to set trgmii pll: %d\n", ret);
 		return;
 	}
 
-	val = (speed == SPEED_1000) ?
-		INTF_MODE_RGMII_1000 : INTF_MODE_RGMII_10_100;
-	mtk_w32(eth, val, INTF_MODE);
+	if (speed == SPEED_1000) {
+		intf = INTF_MODE_RGMII_1000;
+		rate = 250000000;
+		rck = RCK_CTRL_RGMII_1000;
+		tck = TCK_CTRL_RGMII_1000;
+	} else {
+		intf = INTF_MODE_RGMII_10_100;
+		rate = 500000000;
+		rck = RCK_CTRL_RGMII_10_100;
+		tck = TCK_CTRL_RGMII_10_100;
+	}
+
+	mtk_w32(eth, intf, INTF_MODE);
 
 	regmap_update_bits(eth->ethsys, ETHSYS_CLKCFG0,
 			   ETHSYS_TRGMII_CLK_SEL362_5,
 			   ETHSYS_TRGMII_CLK_SEL362_5);
 
-	val = (speed == SPEED_1000) ? 250000000 : 500000000;
-	ret = clk_set_rate(eth->clks[MTK_CLK_TRGPLL], val);
+	ret = clk_set_rate(eth->clks[MTK_CLK_TRGPLL], rate);
 	if (ret)
 		dev_err(eth->dev, "Failed to set trgmii pll: %d\n", ret);
 
-	val = (speed == SPEED_1000) ?
-		RCK_CTRL_RGMII_1000 : RCK_CTRL_RGMII_10_100;
-	mtk_w32(eth, val, TRGMII_RCK_CTRL);
-
-	val = (speed == SPEED_1000) ?
-		TCK_CTRL_RGMII_1000 : TCK_CTRL_RGMII_10_100;
-	mtk_w32(eth, val, TRGMII_TCK_CTRL);
+	mtk_w32(eth, rck, TRGMII_RCK_CTRL);
+	mtk_w32(eth, tck, TRGMII_TCK_CTRL);
 }
 
 static struct phylink_pcs *mtk_mac_select_pcs(struct phylink_config *config,
Signature · 1 line
2.30.2
#2 lore raw

PATCH 2/4 net: mtk_eth_soc: move trgmii ddr2 check to probe function

In reply to Russell King (Oracle)

If TRGMII mode is not permitted when using DDR2 mode, we should handle that when setting up phylink's ->supported_interfaces so phylink knows that this is not supported by the hardware. Move this check to mtk_add_mac().

---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 21 ++++++++++-----------
 1 file changed, 10 insertions(+), 11 deletions(-)
drivers/net/ethernet/mediatek/mtk_eth_soc.c +10 -11
index c63f17929ccf..1b385dfe620f 100644
@@ -374,17 +374,6 @@ static int mt7621_gmac0_rgmii_adjust(struct mtk_eth *eth,
 {
 	u32 val;
 
-	/* Check DDR memory type.
-	 * Currently TRGMII mode with DDR2 memory is not supported.
-	 */
-	regmap_read(eth->ethsys, ETHSYS_SYSCFG, &val);
-	if (interface == PHY_INTERFACE_MODE_TRGMII &&
-	    val & SYSCFG_DRAM_TYPE_DDR2) {
-		dev_err(eth->dev,
-			"TRGMII mode with DDR2 memory is not supported!\n");
-		return -EOPNOTSUPP;
-	}
-
 	val = (interface == PHY_INTERFACE_MODE_TRGMII) ?
 		ETHSYS_TRGMII_MT7621_DDR_PLL : 0;
 
@@ -4333,6 +4322,7 @@ static int mtk_add_mac(struct mtk_eth *eth, struct device_node *np)
 	struct mtk_mac *mac;
 	int id, err;
 	int txqs = 1;
+	u32 val;
 
 	if (!_id) {
 		dev_err(eth->dev, "missing mac id\n");
@@ -4409,6 +4399,15 @@ static int mtk_add_mac(struct mtk_eth *eth, struct device_node *np)
 		__set_bit(PHY_INTERFACE_MODE_TRGMII,
 			  mac->phylink_config.supported_interfaces);
 
+	/* TRGMII is not permitted on MT7621 if using DDR2 */
+	if (MTK_HAS_CAPS(mac->hw->soc->caps, MTK_GMAC1_TRGMII) &&
+	    MTK_HAS_CAPS(mac->hw->soc->caps, MTK_TRGMII_MT7621_CLK)) {
+		regmap_read(eth->ethsys, ETHSYS_SYSCFG, &val);
+		if (val & SYSCFG_DRAM_TYPE_DDR2)
+			__clear_bit(PHY_INTERFACE_MODE_TRGMII,
+				    mac->phylink_config.supported_interfaces);
+	}
+
 	if (MTK_HAS_CAPS(mac->hw->soc->caps, MTK_SGMII)) {
 		__set_bit(PHY_INTERFACE_MODE_SGMII,
 			  mac->phylink_config.supported_interfaces);
Signature · 1 line
2.30.2
#3 lore raw

PATCH 3/4 net: mtk_eth_soc: remove unnecessary checks in mtk_mac_config()

In reply to Russell King (Oracle)

mtk_mac_config() checks that the interface mode is permitted for the capabilities, but we already do these checks in mtk_add_mac() when initialising phylink's supported_interfaces bitmap. Remove the unnecessary tests.

---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 14 +++-----------
 1 file changed, 3 insertions(+), 11 deletions(-)
drivers/net/ethernet/mediatek/mtk_eth_soc.c +3 -11
index 1b385dfe620f..f78810717f66 100644
@@ -458,12 +458,6 @@ static void mtk_mac_config(struct phylink_config *config, unsigned int mode,
 		/* Setup soc pin functions */
 		switch (state->interface) {
 		case PHY_INTERFACE_MODE_TRGMII:
-			if (mac->id)
-				goto err_phy;
-			if (!MTK_HAS_CAPS(mac->hw->soc->caps,
-					  MTK_GMAC1_TRGMII))
-				goto err_phy;
-			fallthrough;
 		case PHY_INTERFACE_MODE_RGMII_TXID:
 		case PHY_INTERFACE_MODE_RGMII_RXID:
 		case PHY_INTERFACE_MODE_RGMII_ID:
@@ -480,11 +474,9 @@ static void mtk_mac_config(struct phylink_config *config, unsigned int mode,
 		case PHY_INTERFACE_MODE_1000BASEX:
 		case PHY_INTERFACE_MODE_2500BASEX:
 		case PHY_INTERFACE_MODE_SGMII:
-			if (MTK_HAS_CAPS(eth->soc->caps, MTK_SGMII)) {
-				err = mtk_gmac_sgmii_path_setup(eth, mac->id);
-				if (err)
-					goto init_err;
-			}
+			err = mtk_gmac_sgmii_path_setup(eth, mac->id);
+			if (err)
+				goto init_err;
 			break;
 		case PHY_INTERFACE_MODE_GMII:
 			if (MTK_HAS_CAPS(eth->soc->caps, MTK_GEPHY)) {
Signature · 1 line
2.30.2
#4 lore raw

PATCH 4/4 net: mtk_eth_soc: remove support for RMII and REVMII modes

In reply to Russell King (Oracle)

Since the conversion of mtk_eth_soc to phylink's supported_interfaces bitmap, these two modes have not been selectable. No one has raised this as an issue. Checking the in-kernel DT files, none of them use either of these modes with this hardware.

Daniel Golle concurs:

A quick grep through the device trees of the more than 650 ramips and mediatek boards we support in OpenWrt has revealed that *none* of them uses either reduced-MII or reverse-MII PHY modes. I could imaging that some more specialized ramips boards may use the RMII 100M PHY mode to connect with exotic PHYs for industrial or automotive applications (think: for 100BASE-T1 PHY connected via RMII). I have never seen or touched such boards, but there are hints that they do exist.

For reverse-MII there are cases in which the Ralink SoC (Rt305x, for example) is used in iNIC mode, ie. connected as a PHY to another SoC, and running only a minimal firmware rather than running Linux. Due to the lack of external DRAM for the Ralink SoC on this kind of boards, the Ralink SoC there will anyway never be able to boot Linux. I've seen this e.g. in multimedia devices like early WiFi-connected not-yet-so-smart TVs.

Consequently, the conclusion is that no one uses these modes with this hardware, so we might as well drop support for them.

---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 12 +-----------
 1 file changed, 1 insertion(+), 11 deletions(-)
drivers/net/ethernet/mediatek/mtk_eth_soc.c +1 -11
index f78810717f66..b22cd160554e 100644
@@ -463,8 +463,6 @@ static void mtk_mac_config(struct phylink_config *config, unsigned int mode,
 		case PHY_INTERFACE_MODE_RGMII_ID:
 		case PHY_INTERFACE_MODE_RGMII:
 		case PHY_INTERFACE_MODE_MII:
-		case PHY_INTERFACE_MODE_REVMII:
-		case PHY_INTERFACE_MODE_RMII:
 			if (MTK_HAS_CAPS(eth->soc->caps, MTK_RGMII)) {
 				err = mtk_gmac_rgmii_path_setup(eth, mac->id);
 				if (err)
@@ -524,21 +522,13 @@ static void mtk_mac_config(struct phylink_config *config, unsigned int mode,
 			}
 		}
 
-		ge_mode = 0;
 		switch (state->interface) {
 		case PHY_INTERFACE_MODE_MII:
 		case PHY_INTERFACE_MODE_GMII:
 			ge_mode = 1;
 			break;
-		case PHY_INTERFACE_MODE_REVMII:
-			ge_mode = 2;
-			break;
-		case PHY_INTERFACE_MODE_RMII:
-			if (mac->id)
-				goto err_phy;
-			ge_mode = 3;
-			break;
 		default:
+			ge_mode = 0;
 			break;
 		}
 
Signature · 1 line
2.30.2
#5 lore raw
In reply to Russell King (Oracle)
This series was applied to netdev/net-next.git (main) by Paolo Abeni <[email protected]>:

Hello:

This series was applied to netdev/net-next.git (main) by Paolo Abeni <[email protected]>:

Quoted 8 lines · On Tue, 7 Mar 2023 16:19:02 +0000 you wrote:

Here are a number of patches that do a bit of cleanup to mtk_eth_soc.

The first patch cleans up mtk_gmac0_rgmii_adjust(), which is the troublesome function preventing the driver becoming a post-March2020 phylink driver. It doesn't solve that problem, merely makes the code easier to follow by getting rid of repeated tenary operators.

[...]

Here is the summary with links:
- [net-next,1/4] net: mtk_eth_soc: tidy mtk_gmac0_rgmii_adjust()

    https://git.kernel.org/netdev/net-next/c/04eb3d1cede0
  - [net-next,2/4] net: mtk_eth_soc: move trgmii ddr2 check to probe function
    https://git.kernel.org/netdev/net-next/c/7910898e1b2a
  - [net-next,3/4] net: mtk_eth_soc: remove unnecessary checks in mtk_mac_config()
    https://git.kernel.org/netdev/net-next/c/c9f9e3a3289f
  - [net-next,4/4] net: mtk_eth_soc: remove support for RMII and REVMII modes
    https://git.kernel.org/netdev/net-next/c/8cd9de08ccf6

You are awesome, thank you!

Signature · 2 lines
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html