s2idle on kdell xps 9730 does go to sleep but laptop is warm
and burn a lot of battery during full kernel sleep Reply-To:
X-Sysadmin: BOFH
X-URL: http://marc.merlins.org/
With kernel 6.6.9 when I put the laptop to sleep, syslog shows that the laptop was sleeping for 9h, fans were stopped, but when I gabbed my laptop it was warm and burned 80% of the battery overnight.
And yet, linux was not running, my logs show the kernel went into ACPI sleep and back out
Logs show the system slept for 9h and went to sleep with s2idle.
Is it the wrong sleep outside of suspend to disk and full shutdown?
Are there devices that should have been powered off but didn't (evidently yes since battery loss was 80% and laptop was warm)
logs below
2025-05-14T00:01:20 merlin root: >>>>>>>>>> suspend #1 1747206080
2025-05-14T00:01:21 merlin dbus-daemon[2846]: [system] Activating via systemd: service name='org.wicd.daemon' unit='dbus-org.wicd.daemon.service' requested by ':1.1130' (uid=0 pid=3357435 comm="/usr/bin/python3 /usr/share/wicd/daemon/suspend.py") 2025-05-14T00:01:21 merlin dbus-daemon[2846]: [system] Activation via systemd failed for unit 'dbus-org.wicd.daemon.service': Unit dbus-org.wicd.daemon.service not found. 2025-05-14T00:01:21 merlin kernel: [1388664.621668] PM: suspend entry (s2idle) 2025-05-14T00:01:21 merlin kernel: [1388664.625122] Filesystems sync: 0.003 seconds 2025-05-14T09:20:43 merlin kernel: [1388664.635518] Freezing user space processes 2025-05-14T09:20:43 merlin kernel: [1388664.638313] Freezing user space processes completed (elapsed 0.002 seconds) 2025-05-14T09:20:43 merlin kernel: [1388664.638320] OOM killer disabled. 2025-05-14T09:20:43 merlin kernel: [1388664.638322] Freezing remaining freezable tasks 2025-05-14T09:20:43 merlin kernel: [1388664.640285] Freezing remaining freezable tasks completed (elapsed 0.001 seconds) 2025-05-14T09:20:43 merlin kernel: [1388664.640290] printk: Suspending console(s) (use no_console_suspend to debug) (...) 2025-05-14T09:20:43 merlin kernel: [1422225.195325] OOM killer enabled. 2025-05-14T09:20:43 merlin kernel: [1422225.195328] Restarting tasks ... done. 2025-05-14T09:20:43 merlin kernel: [1422225.204356] vgaarb: client 0x00000000f7b9cd5c called 'target' 2025-05-14T09:20:43 merlin kernel: [1422225.204376] vgaarb: PCI:0000:00:02.0 ==> 0000:00:02.0 pdev 00000000dec5b5e7 2025-05-14T09:20:43 merlin kernel: [1422225.204383] vgaarb: vgadev 00000000dca48b8a 2025-05-14T09:20:43 merlin kernel: [1422225.321870] PM: suspend exit
Thanks,
Marc
Signature · 3 lines
"A mouse is a device used to point at the xterm you want to type in" - A.S.R. Home page: http://marc.merlins.org/ | PGP 7F55D5F27AAF9D08
This is still a problem. Is there more info I can provide? For now it's bad enough that I can't have the battery be in S3 sleep for 24H without the batteries running out :-/
Quoted 48 lines · Marc MERLIN
and burn a lot of battery during full kernel sleep Reply-To:
X-Sysadmin: BOFH
X-URL: http://marc.merlins.org/With kernel 6.6.9 when I put the laptop to sleep, syslog shows that the laptop was sleeping for 9h, fans were stopped, but when I gabbed my laptop it was warm and burned 80% of the battery overnight.
And yet, linux was not running, my logs show the kernel went into ACPI sleep and back out
Logs show the system slept for 9h and went to sleep with s2idle.
Is it the wrong sleep outside of suspend to disk and full shutdown?
Are there devices that should have been powered off but didn't (evidently yes since battery loss was 80% and laptop was warm)
logs below
2025-05-14T00:01:20 merlin root: >>>>>>>>>> suspend #1 17472060802025-05-14T00:01:21 merlin dbus-daemon[2846]: [system] Activating via systemd: service name='org.wicd.daemon' unit='dbus-org.wicd.daemon.service' requested by ':1.1130' (uid=0 pid=3357435 comm="/usr/bin/python3 /usr/share/wicd/daemon/suspend.py") 2025-05-14T00:01:21 merlin dbus-daemon[2846]: [system] Activation via systemd failed for unit 'dbus-org.wicd.daemon.service': Unit dbus-org.wicd.daemon.service not found. 2025-05-14T00:01:21 merlin kernel: [1388664.621668] PM: suspend entry (s2idle) 2025-05-14T00:01:21 merlin kernel: [1388664.625122] Filesystems sync: 0.003 seconds 2025-05-14T09:20:43 merlin kernel: [1388664.635518] Freezing user space processes 2025-05-14T09:20:43 merlin kernel: [1388664.638313] Freezing user space processes completed (elapsed 0.002 seconds) 2025-05-14T09:20:43 merlin kernel: [1388664.638320] OOM killer disabled. 2025-05-14T09:20:43 merlin kernel: [1388664.638322] Freezing remaining freezable tasks 2025-05-14T09:20:43 merlin kernel: [1388664.640285] Freezing remaining freezable tasks completed (elapsed 0.001 seconds) 2025-05-14T09:20:43 merlin kernel: [1388664.640290] printk: Suspending console(s) (use no_console_suspend to debug) (...) 2025-05-14T09:20:43 merlin kernel: [1422225.195325] OOM killer enabled. 2025-05-14T09:20:43 merlin kernel: [1422225.195328] Restarting tasks ... done. 2025-05-14T09:20:43 merlin kernel: [1422225.204356] vgaarb: client 0x00000000f7b9cd5c called 'target' 2025-05-14T09:20:43 merlin kernel: [1422225.204376] vgaarb: PCI:0000:00:02.0 ==> 0000:00:02.0 pdev 00000000dec5b5e7 2025-05-14T09:20:43 merlin kernel: [1422225.204383] vgaarb: vgadev 00000000dca48b8a 2025-05-14T09:20:43 merlin kernel: [1422225.321870] PM: suspend exitThanks,
MarcSignature · 3 lines
"A mouse is a device used to point at the xterm you want to type in" - A.S.R. Home page: http://marc.merlins.org/ | PGP 7F55D5F27AAF9D08
Signature · 3 lines
"A mouse is a device used to point at the xterm you want to type in" - A.S.R. Home page: http://marc.merlins.org/ | PGP 7F55D5F27AAF9D08
Quoted 3 lines · Marc MERLIN
This is still a problem. Is there more info I can provide? For now it's bad enough that I can't have the battery be in S3 sleep for 24H without the batteries running out :-/
I believe what is going on is that on more modern systems, it relies on the OS's drivers to power done various peripherals (e.g., graphics, SSD's, etc.) and this is no longer being done by the low-level firmware. With Linux the CPU is put to sleep, but there's a lot more on a modern mainboard than just the CPU....
My solution, two tears ago, was to give up on my Dell XPS 13, and I switched to a M2 MacBook Air, and I run (arm64) Linux in a Parallels VM.
Sigh....
- Ted
Quoted 10 lines · Theodore Ts'o
Quoted 3 lines · Marc MERLIN
This is still a problem. Is there more info I can provide? For now it's bad enough that I can't have the battery be in S3 sleep for 24H without the batteries running out :-/
I believe what is going on is that on more modern systems, it relies on the OS's drivers to power done various peripherals (e.g., graphics, SSD's, etc.) and this is no longer being done by the low-level firmware. With Linux the CPU is put to sleep, but there's a lot more on a modern mainboard than just the CPU....
Hi Ted, nice to hear from you. Yes, I agree that what you wrote totally matches my experience and the reason why the laptop was so warm, even in sleep mode.
So, given that this is not a new problem, are there any new options in linux drivers and/or kernel options to have linux do this (shut down each subsystem)?
Thanks,
Marc
Signature · 3 lines
"A mouse is a device used to point at the xterm you want to type in" - A.S.R. Home page: http://marc.merlins.org/ | PGP 7F55D5F27AAF9D08
Rafael J. Wysocki
maintainerQuoted 9 lines · Marc MERLIN
and burn a lot of battery during full kernel sleep Reply-To:
X-Sysadmin: BOFH
X-URL: http://marc.merlins.org/With kernel 6.6.9 when I put the laptop to sleep, syslog shows that the laptop was sleeping for 9h, fans were stopped, but when I gabbed my laptop it was warm and burned 80% of the battery overnight.
First off, I'd try a newer kernel. Say 6.15.0 (unless you boot with "nosmt" in the kernel command line).
Quoted 2 lines
And yet, linux was not running, my logs show the kernel went into ACPI sleep and back out
It wouldn't be "ACPI sleep" if it was suspend-to-idle.
Quoted 3 lines
Logs show the system slept for 9h and went to sleep with s2idle.
Is it the wrong sleep outside of suspend to disk and full shutdown?
No, it shouldn't be.
Quoted 2 lines
Are there devices that should have been powered off but didn't (evidently yes since battery loss was 80% and laptop was warm)
There seems to be driver support missing for some devices.
Quoted 13 lines
logs below
2025-05-14T00:01:20 merlin root: >>>>>>>>>> suspend #1 17472060802025-05-14T00:01:21 merlin dbus-daemon[2846]: [system] Activating via systemd: service name='org.wicd.daemon' unit='dbus-org.wicd.daemon.service' requested by ':1.1130' (uid=0 pid=3357435 comm="/usr/bin/python3 /usr/share/wicd/daemon/suspend.py") 2025-05-14T00:01:21 merlin dbus-daemon[2846]: [system] Activation via systemd failed for unit 'dbus-org.wicd.daemon.service': Unit dbus-org.wicd.daemon.service not found. 2025-05-14T00:01:21 merlin kernel: [1388664.621668] PM: suspend entry (s2idle) 2025-05-14T00:01:21 merlin kernel: [1388664.625122] Filesystems sync: 0.003 seconds 2025-05-14T09:20:43 merlin kernel: [1388664.635518] Freezing user space processes 2025-05-14T09:20:43 merlin kernel: [1388664.638313] Freezing user space processes completed (elapsed 0.002 seconds) 2025-05-14T09:20:43 merlin kernel: [1388664.638320] OOM killer disabled. 2025-05-14T09:20:43 merlin kernel: [1388664.638322] Freezing remaining freezable tasks 2025-05-14T09:20:43 merlin kernel: [1388664.640285] Freezing remaining freezable tasks completed (elapsed 0.001 seconds)
Quoted 8 lines
2025-05-14T09:20:43 merlin kernel: [1388664.640290] printk: Suspending console(s) (use no_console_suspend to debug) (...) 2025-05-14T09:20:43 merlin kernel: [1422225.195325] OOM killer enabled. 2025-05-14T09:20:43 merlin kernel: [1422225.195328] Restarting tasks ... done. 2025-05-14T09:20:43 merlin kernel: [1422225.204356] vgaarb: client 0x00000000f7b9cd5c called 'target' 2025-05-14T09:20:43 merlin kernel: [1422225.204376] vgaarb: PCI:0000:00:02.0 ==> 0000:00:02.0 pdev 00000000dec5b5e7 2025-05-14T09:20:43 merlin kernel: [1422225.204383] vgaarb: vgadev 00000000dca48b8a 2025-05-14T09:20:43 merlin kernel: [1422225.321870] PM: suspend exit
Well, it obviously is not a complete log.
What processor is there in your system?
Quoted 6 lines · Rafael J. Wysocki
Quoted 3 lines
With kernel 6.6.9 when I put the laptop to sleep, syslog shows that the laptop was sleeping for 9h, fans were stopped, but when I gabbed my laptop it was warm and burned 80% of the battery overnight.
First off, I'd try a newer kernel. Say 6.15.0 (unless you boot with "nosmt" in the kernel command line).
Fair point, I somehow failed to upgrade the kernel on that machine. I have a 6.14.5 kernel I just installed.
I also upgraded all firmware:
dpkggrep firmware | awk '{ print $1 }' | xargs apt-get install -t unstable -y
Quoted 4 lines
Quoted 2 lines
And yet, linux was not running, my logs show the kernel went into ACPI sleep and back out
It wouldn't be "ACPI sleep" if it was suspend-to-idle.
My thinkpad has:
sauron:~# cat /sys/power/mem_sleep s2idle [deep]
The Dell XPS only has:
merlin:/usr/src# cat /sys/power/mem_sleep [s2idle]
Quoted 1 line
What processor is there in your system?
model name : 13th Gen Intel(R) Core(TM) i7-13700H
Quoted 1 line
Well, it obviously is not a complete log.
Ok, I tested again with the new kernel. The laptop didn't feel warm when in sleep, but I lost 20% battery in 4H, which means the battery would not last 24H in sleep
For logs, which one did you want? I have pretty full logs here:
https://marc.merlins.org/tmp/merlin-sleep-6.14.5_dmesg.txt
https://marc.merlins.org/tmp/merlin-sleep-6.14.5_acpi.txt
One thing I changed recently is that unloading wireless altogether, causes issues at times, so now I have
rfkill block wlan
instead of
killall wpa_supplicant &>/dev/null
pkill -f "dhclient.*wlan0"
ifconfig -a | grep -q wlan0 && ifconfig wlan0 down
rmmod iwlmvm
rmmod iwlwifi iwlagn iwlcore
rmmod ieee80211
rmmod ieee80211_crypt_wep 2>/dev/null
rmmod ieee80211_crypt_tkip 2>/dev/null
rmmod ieee80211_crypt 2>/dev/null
rmmod mac80211 2>/dev/null
rmmod cfg80211 2>/dev/null
This bit of dmesg just before sleep may be relevant:
[ 226.365652] thunderbolt 0000:00:0d.2: save config 0x34: 0x00000080 [ 226.365654] thunderbolt 0000:00:0d.3: save config 0x2c: 0x0bda1028 [ 226.365655] thunderbolt 0000:00:0d.2: save config 0x38: 0x00000000 [ 226.365656] thunderbolt 0000:00:0d.3: save config 0x30: 0x00000000 [ 226.365657] thunderbolt 0000:00:0d.2: save config 0x3c: 0x000001ff [ 226.365659] thunderbolt 0000:00:0d.3: save config 0x34: 0x00000080 [ 226.365661] thunderbolt 0000:00:0d.3: save config 0x38: 0x00000000 [ 226.365663] thunderbolt 0000:00:0d.3: save config 0x3c: 0x000001ff [ 226.366245] thunderbolt 0000:00:0d.2: PME# enabled [ 226.366424] thunderbolt 0000:00:0d.3: PME# enabled [ 226.370305] pcieport 10000:e0:06.2: PCI PM: Suspend power state: D3hot [ 226.370328] pcieport 10000:e0:06.0: PCI PM: Suspend power state: D3hot [ 226.370539] vmd 0000:00:0e.0: save config 0x00: 0xa77f8086 [ 226.370551] vmd 0000:00:0e.0: save config 0x04: 0x00100406 [ 226.370555] vmd 0000:00:0e.0: save config 0x08: 0x01040000 [ 226.370560] vmd 0000:00:0e.0: save config 0x0c: 0x00800000 [ 226.370565] vmd 0000:00:0e.0: save config 0x10: 0x02000004 [ 226.370575] vmd 0000:00:0e.0: save config 0x14: 0x00000062 [ 226.370581] vmd 0000:00:0e.0: save config 0x18: 0x72000000 [ 226.370587] vmd 0000:00:0e.0: save config 0x1c: 0x00000000 [ 226.370592] vmd 0000:00:0e.0: save config 0x20: 0x07900004 [ 226.370596] vmd 0000:00:0e.0: save config 0x24: 0x00000062 [ 226.370600] vmd 0000:00:0e.0: save config 0x28: 0x00000000 [ 226.370603] vmd 0000:00:0e.0: save config 0x2c: 0x0bda1028 [ 226.370607] vmd 0000:00:0e.0: save config 0x30: 0x00000000 [ 226.370611] vmd 0000:00:0e.0: save config 0x34: 0x00000080 [ 226.370615] vmd 0000:00:0e.0: save config 0x38: 0x00000000 [ 226.370620] vmd 0000:00:0e.0: save config 0x3c: 0x00000000 [ 226.375481] intel-lpss 0000:00:15.1: ACPI _REG disconnect evaluation failed (5) [ 226.375487] mei_me 0000:00:16.0: PCI PM: Suspend power state: D3hot [ 226.375908] intel-lpss 0000:00:15.0: ACPI _REG disconnect evaluation failed (5) [ 226.376162] proc_thermal_pci 0000:00:04.0: PCI PM: Suspend power state: D3hot [ 226.377183] intel-lpss 0000:00:15.1: power state changed by ACPI to D3hot [ 226.377277] intel-lpss 0000:00:15.1: PCI PM: Suspend power state: D3hot [ 226.377771] intel-lpss 0000:00:15.0: power state changed by ACPI to D3hot [ 226.378257] rtsx_pci 0000:06:00.0: PCI PM: Suspend power state: D3hot [ 226.378422] intel-lpss 0000:00:15.0: PCI PM: Suspend power state: D3hot [ 226.378448] pcieport 0000:00:1c.0: save config 0x00: 0x51bb8086 [ 226.378607] pcieport 0000:00:1c.0: save config 0x04: 0x00100407 [ 226.378656] pcieport 0000:00:1c.0: save config 0x08: 0x06040001 [ 226.378707] pcieport 0000:00:1c.0: save config 0x0c: 0x00810000 [ 226.378758] pcieport 0000:00:1c.0: save config 0x10: 0x00000000 [ 226.378782] pcieport 0000:00:1c.0: save config 0x14: 0x00000000 [ 226.378806] pcieport 0000:00:1c.0: save config 0x18: 0x00060600 [ 226.378830] pcieport 0000:00:1c.0: save config 0x1c: 0x000000f0 [ 226.378853] pcieport 0000:00:1c.0: save config 0x20: 0x75007500 [ 226.378877] pcieport 0000:00:1c.0: save config 0x24: 0x0001fff1 [ 226.378899] pcieport 0000:00:1c.0: save config 0x28: 0x00000000 [ 226.378905] pcieport 0000:00:1c.0: save config 0x2c: 0x00000000 [ 226.378935] pcieport 0000:00:1c.0: save config 0x30: 0x00000000 [ 226.378958] pcieport 0000:00:1c.0: save config 0x34: 0x00000040 [ 226.378982] pcieport 0000:00:1c.0: save config 0x38: 0x00000000 [ 226.379006] pcieport 0000:00:1c.0: save config 0x3c: 0x000204ff [ 226.379534] pcieport 0000:00:1c.0: PME# enabled [ 226.379589] thunderbolt 0000:00:0d.2: ACPI _REG disconnect evaluation failed (5) [ 226.380218] xhci_hcd 0000:00:0d.0: ACPI _REG disconnect evaluation failed (5) [ 226.381101] thunderbolt 0000:00:0d.3: ACPI _REG disconnect evaluation failed (5) [ 226.382316] iwlwifi 0000:00:14.3: power state changed by ACPI to D3hot [ 226.382528] iwlwifi 0000:00:14.3: PCI PM: Suspend power state: D3hot [ 226.383140] vmd 0000:00:0e.0: ACPI _REG disconnect evaluation failed (5) [ 226.384467] xhci_hcd 0000:00:14.0: power state changed by ACPI to D3hot [ 226.384574] xhci_hcd 0000:00:14.0: PCI PM: Suspend power state: D3hot [ 226.384813] vmd 0000:00:0e.0: power state changed by ACPI to D3hot [ 226.384825] vmd 0000:00:0e.0: PCI PM: Suspend power state: D3hot [ 226.385180] xhci_hcd 0000:00:0d.0: power state changed by ACPI to D3cold [ 226.385191] xhci_hcd 0000:00:0d.0: PCI PM: Suspend power state: D3cold [ 226.391528] pcieport 0000:00:1c.0: ACPI _REG disconnect evaluation failed (5) [ 226.392369] pcieport 0000:00:1c.0: power state changed by ACPI to D3hot [ 226.392484] pcieport 0000:00:1c.0: PCI PM: Suspend power state: D3hot [ 226.395162] thunderbolt 0000:00:0d.2: power state changed by ACPI to D3cold [ 226.395172] thunderbolt 0000:00:0d.2: PCI PM: Suspend power state: D3cold [ 226.396283] thunderbolt 0000:00:0d.3: power state changed by ACPI to D3cold [ 226.396291] thunderbolt 0000:00:0d.3: PCI PM: Suspend power state: D3cold [14916.770339] ACPI: EC: interrupt unblocked
Signature · 3 lines
"A mouse is a device used to point at the xterm you want to type in" - A.S.R. Home page: http://marc.merlins.org/ | PGP 7F55D5F27AAF9D08
Were the logs I gave useful in any way, or just confirm that it's just some new-ish laptop (2 years old now) that sadly does things in ways that don't work well with linux?
https://marc.merlins.org/tmp/merlin-sleep-6.14.5_dmesg.txt
https://marc.merlins.org/tmp/merlin-sleep-6.14.5_acpi.txt
Quoted 137 lines · Marc MERLIN
Quoted 6 lines · Rafael J. Wysocki
Quoted 3 lines
With kernel 6.6.9 when I put the laptop to sleep, syslog shows that the laptop was sleeping for 9h, fans were stopped, but when I gabbed my laptop it was warm and burned 80% of the battery overnight.
First off, I'd try a newer kernel. Say 6.15.0 (unless you boot with "nosmt" in the kernel command line).
Fair point, I somehow failed to upgrade the kernel on that machine. I have a 6.14.5 kernel I just installed.
I also upgraded all firmware:
dpkggrep firmware | awk '{ print $1 }' | xargs apt-get install -t unstable -yQuoted 4 lines
Quoted 2 lines
And yet, linux was not running, my logs show the kernel went into ACPI sleep and back out
It wouldn't be "ACPI sleep" if it was suspend-to-idle.
My thinkpad has:
sauron:~# cat /sys/power/mem_sleep s2idle [deep]The Dell XPS only has:
merlin:/usr/src# cat /sys/power/mem_sleep [s2idle]Quoted 1 line
What processor is there in your system?
model name : 13th Gen Intel(R) Core(TM) i7-13700H
Quoted 1 line
Well, it obviously is not a complete log.
Ok, I tested again with the new kernel. The laptop didn't feel warm when in sleep, but I lost 20% battery in 4H, which means the battery would not last 24H in sleep
For logs, which one did you want? I have pretty full logs here:
https://marc.merlins.org/tmp/merlin-sleep-6.14.5_dmesg.txt
https://marc.merlins.org/tmp/merlin-sleep-6.14.5_acpi.txtOne thing I changed recently is that unloading wireless altogether, causes issues at times, so now I have
rfkill block wlan
instead of
killallwpa_supplicant&>/dev/null
pkill -f "dhclient.*wlan0"
ifconfig -a | grep -q wlan0 && ifconfig wlan0 down
rmmod iwlmvm
rmmod iwlwifi iwlagn iwlcore
rmmod ieee80211
rmmodieee80211_crypt_wep2>/dev/null
rmmodieee80211_crypt_tkip2>/dev/null
rmmodieee80211_crypt2>/dev/null
rmmod mac80211 2>/dev/null
rmmod cfg80211 2>/dev/nullThis bit of dmesg just before sleep may be relevant:
[ 226.365652] thunderbolt 0000:00:0d.2: save config 0x34: 0x00000080 [ 226.365654] thunderbolt 0000:00:0d.3: save config 0x2c: 0x0bda1028 [ 226.365655] thunderbolt 0000:00:0d.2: save config 0x38: 0x00000000 [ 226.365656] thunderbolt 0000:00:0d.3: save config 0x30: 0x00000000 [ 226.365657] thunderbolt 0000:00:0d.2: save config 0x3c: 0x000001ff [ 226.365659] thunderbolt 0000:00:0d.3: save config 0x34: 0x00000080 [ 226.365661] thunderbolt 0000:00:0d.3: save config 0x38: 0x00000000 [ 226.365663] thunderbolt 0000:00:0d.3: save config 0x3c: 0x000001ff [ 226.366245] thunderbolt 0000:00:0d.2: PME# enabled [ 226.366424] thunderbolt 0000:00:0d.3: PME# enabled [ 226.370305] pcieport 10000:e0:06.2: PCI PM: Suspend power state: D3hot [ 226.370328] pcieport 10000:e0:06.0: PCI PM: Suspend power state: D3hot [ 226.370539] vmd 0000:00:0e.0: save config 0x00: 0xa77f8086 [ 226.370551] vmd 0000:00:0e.0: save config 0x04: 0x00100406 [ 226.370555] vmd 0000:00:0e.0: save config 0x08: 0x01040000 [ 226.370560] vmd 0000:00:0e.0: save config 0x0c: 0x00800000 [ 226.370565] vmd 0000:00:0e.0: save config 0x10: 0x02000004 [ 226.370575] vmd 0000:00:0e.0: save config 0x14: 0x00000062 [ 226.370581] vmd 0000:00:0e.0: save config 0x18: 0x72000000 [ 226.370587] vmd 0000:00:0e.0: save config 0x1c: 0x00000000 [ 226.370592] vmd 0000:00:0e.0: save config 0x20: 0x07900004 [ 226.370596] vmd 0000:00:0e.0: save config 0x24: 0x00000062 [ 226.370600] vmd 0000:00:0e.0: save config 0x28: 0x00000000 [ 226.370603] vmd 0000:00:0e.0: save config 0x2c: 0x0bda1028 [ 226.370607] vmd 0000:00:0e.0: save config 0x30: 0x00000000 [ 226.370611] vmd 0000:00:0e.0: save config 0x34: 0x00000080 [ 226.370615] vmd 0000:00:0e.0: save config 0x38: 0x00000000 [ 226.370620] vmd 0000:00:0e.0: save config 0x3c: 0x00000000 [ 226.375481] intel-lpss 0000:00:15.1: ACPI _REG disconnect evaluation failed (5) [ 226.375487] mei_me 0000:00:16.0: PCI PM: Suspend power state: D3hot [ 226.375908] intel-lpss 0000:00:15.0: ACPI _REG disconnect evaluation failed (5) [ 226.376162] proc_thermal_pci 0000:00:04.0: PCI PM: Suspend power state: D3hot [ 226.377183] intel-lpss 0000:00:15.1: power state changed by ACPI to D3hot [ 226.377277] intel-lpss 0000:00:15.1: PCI PM: Suspend power state: D3hot [ 226.377771] intel-lpss 0000:00:15.0: power state changed by ACPI to D3hot [ 226.378257] rtsx_pci 0000:06:00.0: PCI PM: Suspend power state: D3hot [ 226.378422] intel-lpss 0000:00:15.0: PCI PM: Suspend power state: D3hot [ 226.378448] pcieport 0000:00:1c.0: save config 0x00: 0x51bb8086 [ 226.378607] pcieport 0000:00:1c.0: save config 0x04: 0x00100407 [ 226.378656] pcieport 0000:00:1c.0: save config 0x08: 0x06040001 [ 226.378707] pcieport 0000:00:1c.0: save config 0x0c: 0x00810000 [ 226.378758] pcieport 0000:00:1c.0: save config 0x10: 0x00000000 [ 226.378782] pcieport 0000:00:1c.0: save config 0x14: 0x00000000 [ 226.378806] pcieport 0000:00:1c.0: save config 0x18: 0x00060600 [ 226.378830] pcieport 0000:00:1c.0: save config 0x1c: 0x000000f0 [ 226.378853] pcieport 0000:00:1c.0: save config 0x20: 0x75007500 [ 226.378877] pcieport 0000:00:1c.0: save config 0x24: 0x0001fff1 [ 226.378899] pcieport 0000:00:1c.0: save config 0x28: 0x00000000 [ 226.378905] pcieport 0000:00:1c.0: save config 0x2c: 0x00000000 [ 226.378935] pcieport 0000:00:1c.0: save config 0x30: 0x00000000 [ 226.378958] pcieport 0000:00:1c.0: save config 0x34: 0x00000040 [ 226.378982] pcieport 0000:00:1c.0: save config 0x38: 0x00000000 [ 226.379006] pcieport 0000:00:1c.0: save config 0x3c: 0x000204ff [ 226.379534] pcieport 0000:00:1c.0: PME# enabled [ 226.379589] thunderbolt 0000:00:0d.2: ACPI _REG disconnect evaluation failed (5) [ 226.380218] xhci_hcd 0000:00:0d.0: ACPI _REG disconnect evaluation failed (5) [ 226.381101] thunderbolt 0000:00:0d.3: ACPI _REG disconnect evaluation failed (5) [ 226.382316] iwlwifi 0000:00:14.3: power state changed by ACPI to D3hot [ 226.382528] iwlwifi 0000:00:14.3: PCI PM: Suspend power state: D3hot [ 226.383140] vmd 0000:00:0e.0: ACPI _REG disconnect evaluation failed (5) [ 226.384467] xhci_hcd 0000:00:14.0: power state changed by ACPI to D3hot [ 226.384574] xhci_hcd 0000:00:14.0: PCI PM: Suspend power state: D3hot [ 226.384813] vmd 0000:00:0e.0: power state changed by ACPI to D3hot [ 226.384825] vmd 0000:00:0e.0: PCI PM: Suspend power state: D3hot [ 226.385180] xhci_hcd 0000:00:0d.0: power state changed by ACPI to D3cold [ 226.385191] xhci_hcd 0000:00:0d.0: PCI PM: Suspend power state: D3cold [ 226.391528] pcieport 0000:00:1c.0: ACPI _REG disconnect evaluation failed (5) [ 226.392369] pcieport 0000:00:1c.0: power state changed by ACPI to D3hot [ 226.392484] pcieport 0000:00:1c.0: PCI PM: Suspend power state: D3hot [ 226.395162] thunderbolt 0000:00:0d.2: power state changed by ACPI to D3cold [ 226.395172] thunderbolt 0000:00:0d.2: PCI PM: Suspend power state: D3cold [ 226.396283] thunderbolt 0000:00:0d.3: power state changed by ACPI to D3cold [ 226.396291] thunderbolt 0000:00:0d.3: PCI PM: Suspend power state: D3cold [14916.770339] ACPI: EC: interrupt unblockedSignature · 3 lines
"A mouse is a device used to point at the xterm you want to type in" - A.S.R. Home page: http://marc.merlins.org/ | PGP 7F55D5F27AAF9D08
Signature · 3 lines
"A mouse is a device used to point at the xterm you want to type in" - A.S.R. Home page: http://marc.merlins.org/ | PGP 7F55D5F27AAF9D08