platform/x86: int3472: Add GPIO type 0x02 (strobe) mapping
PATCH 1/1 platform/x86: int3472: Add GPIO type 0x02 (strobe) mapping
Some ACPI tables on Intel Meteor Lake and Arrow Lake platforms define GPIO resources with type 0x02 for INT3472 camera sensor power control. This type is not currently handled, causing a "GPIO type 0x02 unknown; the sensor may not work" warning and preventing proper sensor power sequencing.
Map GPIO type 0x02 (strobe) to the privacy LED handler, matching the approach used for similar illumination-related GPIOs. This is consistent with the original proposal by Hao Yao [1].
Tested on a Dell Pro Max 16 Premium (Arrow Lake-H) with OmniVision OV08F4 sensor connected via Intel IPU6 and Synaptics SVP7500 USBIO bridge. With this patch applied, the int3472-discrete driver no longer warns about unknown GPIO type 0x02, and the sensor probes successfully.
[1] https://lore.kernel.org/all/[email protected]/
--- drivers/platform/x86/intel/int3472/discrete.c | 3 +++ include/linux/platform_data/x86/int3472.h | 1 + 2 files changed, 4 insertions(+)
drivers/platform/x86/intel/int3472/discrete.c +3 -0
@@ -211,6 +211,7 @@ static void int3472_get_con_id_and_polarity(struct int3472_discrete_device *int3 *con_id ="clk-enable" ; *gpio_flags =GPIO_ACTIVE_HIGH ;break ; +case INT3472_GPIO_TYPE_STROBE :case INT3472_GPIO_TYPE_PRIVACY_LED : *con_id ="privacy-led" ; *gpio_flags =GPIO_ACTIVE_HIGH ;
@@ -330,6 +331,7 @@ static int skl_int3472_handle_gpio_resources(struct acpi_resource *ares,break ;case INT3472_GPIO_TYPE_CLK_ENABLE : +case INT3472_GPIO_TYPE_STROBE :case INT3472_GPIO_TYPE_PRIVACY_LED :case INT3472_GPIO_TYPE_POWER_ENABLE :case INT3472_GPIO_TYPE_HANDSHAKE :
@@ -347,6 +349,7 @@ static int skl_int3472_handle_gpio_resources(struct acpi_resource *ares, err_msg ="Failed to register clock\n" ;break ; +case INT3472_GPIO_TYPE_STROBE :case INT3472_GPIO_TYPE_PRIVACY_LED : ret =skl_int3472_register_pled (int3472, gpio);if (ret)
include/linux/platform_data/x86/int3472.h +1 -0
@@ -23,6 +23,7 @@/* PMIC GPIO Types */ #define INT3472_GPIO_TYPE_RESET 0x00#define INT3472_GPIO_TYPE_POWERDOWN 0x01 +#define INT3472_GPIO_TYPE_STROBE 0x02#define INT3472_GPIO_TYPE_POWER_ENABLE 0x0b#define INT3472_GPIO_TYPE_CLK_ENABLE 0x0c#define INT3472_GPIO_TYPE_PRIVACY_LED 0x0d
Signature · 6 lines
2.47.3 -- Marco Nenciarini - [email protected] 7C23 B804 3E65 D298 0A21 B6E2 589F 03F0 1BA5 5038
On Fri, Mar 20, 2026 at 11:35 AM Marco Nenciarini <[email protected]> wrote:
You sent three emails without versioning (no new versions) and no changelog. Please, slow down with that, it's quite confusing. The recommended period between two sequential versions is 24h+. Also see more comments below.
Quoted 10 lines
Some ACPI tables on Intel Meteor Lake and Arrow Lake platforms define GPIO resources with type
0x02for INT3472 camera sensor power control. This type is not currently handled, causing a "GPIO type0x02unknown; the sensor may not work" warning and preventing proper sensor power sequencing.Map GPIO type
0x02(strobe) to the privacy LED handler, matching the approach used for similar illumination-related GPIOs. This is consistent with the original proposal by Hao Yao [1].
Quoted 6 lines
Tested on a Dell Pro Max 16 Premium (Arrow Lake-H) with OmniVision OV08F4 sensor connected via Intel IPU6 and Synaptics SVP7500 USBIO bridge. With this patch applied, the int3472-discrete driver no longer warns about unknown GPIO type
0x02, and the sensor probes successfully.
This should be a Link tag in a form
Quoted 2 lines
These are basically should be Closes: tags
...
Quoted 4 lines
Cc Hao Yao <[email protected]>Cc Hans de Goede <[email protected]>Cc Sakari Ailus <[email protected]>Cc Andy Shevchenko <[email protected]>
These Cc's are better to be after the '---' line below. The Git tooling will recognize them and use them in email as intended.
Quoted 1 line
Signed-off-by Marco Nenciarini <[email protected]>
...
Quoted 2 lines
+ case
INT3472_GPIO_TYPE_STROBE:case INT3472_GPIO_TYPE_PRIVACY_LED:
Hmm... But strobe is usually used for LED flash... We probably need Sakari and/or other Intel camera guys to elaborate on this.
Quoted 2 lines
*con_id = "privacy-led";
*gpio_flags = GPIO_ACTIVE_HIGH;...
Quoted 3 lines
+ case
INT3472_GPIO_TYPE_STROBE:case INT3472_GPIO_TYPE_PRIVACY_LED: ret = skl_int3472_register_pled(int3472, gpio);
Ditto.
Signature · 2 lines
With Best Regards, Andy Shevchenko
Quoted 6 lines · Andy Shevchenko
On Fri, Mar 20, 2026 at 11:35 AM Marco Nenciarini <[email protected]> wrote:
You sent three emails without versioning (no new versions) and no changelog. Please, slow down with that, it's quite confusing. The recommended period between two sequential versions is 24h+. Also see more comments below.
One more thing, this was sent to a partially correct list of stakeholders. You need to use get_maintainer.pl to see who is required to be notified with the proposed change. I have my "smart" script [1] which does this for me based on some heuristic. Feel free to take and use that.
[1]: https://github.com/andy-shev/home-bin-tools/blob/master/ge2maintainer.sh
Signature · 2 lines
With Best Regards, Andy Shevchenko
Hi Andy,
First, apologies for the triple submission. It was a sending error on my side (mutt submitted three separate copies), not three patch versions. Please disregard the duplicates.
Regarding your feedback:
Quoted 1 line
Link tag, Closes tags, Cc placement
Noted, thank you for the clear guidance. I will apply these if I send an updated version.
Quoted 1 line
get_maintainer.pl
Thank you for the pointer and for sharing your ge2maintainer.sh script.
Quoted 1 line
strobe / privacy-led mapping
Hans pointed out that GPIO type 0x02 is actually for an IR flood LED, not a privacy LED. After digging into the ACPI tables on my machine, I confirmed he is correct. The GPIO belongs to an INT3472 controlling an empty IR sensor slot, not the active OV08F4 camera. I have replied to Hans with the full analysis. The mapping in this patch is semantically wrong, so it may not be needed at all, or it would need the refactoring Hans suggested.
Thanks,
Marco
Signature · 2 lines
Marco Nenciarini - [email protected] 7C23 B804 3E65 D298 0A21 B6E2 589F 03F0 1BA5 5038
Hi,
Quoted 6 lines · Marco Nenciarini
Some ACPI tables on Intel Meteor Lake and Arrow Lake platforms define GPIO resources with type
0x02for INT3472 camera sensor power control. This type is not currently handled, causing a "GPIO type0x02unknown; the sensor may not work" warning and preventing proper sensor power sequencing.
Quoted 8 lines
Map GPIO type
0x02(strobe) to the privacy LED handler, matching the approach used for similar illumination-related GPIOs. This is consistent with the original proposal by Hao Yao [1].Tested on a Dell Pro Max 16 Premium (Arrow Lake-H) with OmniVision OV08F4 sensor connected via Intel IPU6 and Synaptics SVP7500 USBIO bridge. With this patch applied, the int3472-discrete driver no longer warns about unknown GPIO type
0x02, and the sensor probes successfully.
The strobe GPIO is typically used only for IR sensors (for Windows Hello) and the OV08F4 / ov08x40 is the regular color sensor.
Did you check with your latest working setup that this patch is necessary at all ? I would expect (other then the warning) things to work fine without this patch, you likely have 2 INT3472 ACPI devices and the one throwing the warning is not used for the OVTI08F4 sensor.
The GPIO with type 0x02 seems to control an IR flood LED to IR illuminate the scene when the IR camera is on. As such mapping it as a privacy LED is not really what we want.
Mapping it as a LED makes sense, but we should give it a different name. So add a name parameter to skl_int3472_register_pled() and rename the function to skl_int3472_register_led().
And then for the existing privacy LED pass: "privacy_led" as name and for the type 0x02 GPIO pass: "ir_flood_led" as name parameter ?
This solves things from the int3472 pov, but is not really helpful otherwise.
Arguably we do want to turn on the ir_flood_led on streaming on automatically like we do for the privacy LED atm. But just using a different name gives us flexibility to allow more fine-grained control in the future ...
Sakari any remarks from the V4L2 side here ?
Regards,
Hans
Quoted 54 lines
[1] https://lore.kernel.org/all/[email protected]/
Cc Hao Yao <[email protected]>Cc Hans de Goede <[email protected]>Cc Sakari Ailus <[email protected]>Cc Andy Shevchenko <[email protected]>Signed-off-by Marco Nenciarini <[email protected]>--- drivers/platform/x86/intel/int3472/discrete.c | 3 +++ include/linux/platform_data/x86/int3472.h | 1 + 2 files changed, 4 insertions(+)drivers/platform/x86/intel/int3472/discrete.c +3
-0@@ -211,6 +211,7 @@ static void int3472_get_con_id_and_polarity(struct int3472_discrete_device *int3 *con_id ="clk-enable" ; *gpio_flags =GPIO_ACTIVE_HIGH ;break ; +case INT3472_GPIO_TYPE_STROBE :case INT3472_GPIO_TYPE_PRIVACY_LED : *con_id ="privacy-led" ; *gpio_flags =GPIO_ACTIVE_HIGH ;@@ -330,6 +331,7 @@ static int skl_int3472_handle_gpio_resources(struct acpi_resource *ares,break ;case INT3472_GPIO_TYPE_CLK_ENABLE : +case INT3472_GPIO_TYPE_STROBE :case INT3472_GPIO_TYPE_PRIVACY_LED :case INT3472_GPIO_TYPE_POWER_ENABLE :case INT3472_GPIO_TYPE_HANDSHAKE :@@ -347,6 +349,7 @@ static int skl_int3472_handle_gpio_resources(struct acpi_resource *ares, err_msg ="Failed to register clock\n" ;break ; +case INT3472_GPIO_TYPE_STROBE :case INT3472_GPIO_TYPE_PRIVACY_LED : ret =skl_int3472_register_pled (int3472, gpio);if (ret)include/linux/platform_data/x86/int3472.h +1
-0@@ -23,6 +23,7 @@/* PMIC GPIO Types */ #define INT3472_GPIO_TYPE_RESET 0x00#define INT3472_GPIO_TYPE_POWERDOWN 0x01 +#define INT3472_GPIO_TYPE_STROBE 0x02#define INT3472_GPIO_TYPE_POWER_ENABLE 0x0b#define INT3472_GPIO_TYPE_CLK_ENABLE 0x0c#define INT3472_GPIO_TYPE_PRIVACY_LED 0x0d
Hi Hans,
Thank you for the detailed review.
You are absolutely right. I dug into the ACPI tables on my Dell Pro Max 16 Premium (Arrow Lake-H) and found the following:
There are 19 INT3472 template devices in the DSDT, but only one is
active: DSC0 (\_SB_.PC00.DSC0, uid=0, status=15). DSC0 has two GPIO entries:
- GPIO entry 1: type 0x12 (HANDSHAKE), pin 1
- GPIO entry 2: type 0x02 (STROBE), pin 48
DSC0 is paired with LNK0 (sensor slot 0), which has no active sensor on this machine. The OV08F4 color sensor is on LNK1, which on Arrow Lake depends on CVSS (INTC10E0, Intel CVS Device), not on any INT3472.
Three sensors are defined in ACPI:
- OVTI08F4 on LNK1 (status=15, active) — the front-facing color camera
- OVTI13B1 on LNK2 (status=0, disabled)
- OVTI01AS on LNK3 (status=0, disabled) — likely the IR sensor
So the GPIO type 0x02 warning comes from an INT3472 that controls a non-existent IR sensor slot. The warning is harmless noise in this case and the patch is not actually needed for the OV08F4 to work.
That said, the patch (or your suggested refactoring with a proper "ir_flood_led" name) would still clean up the warning for any system where an IR sensor slot's INT3472 is enabled without the sensor being present. Would it be worth pursuing as a cleanup, or is it better to just leave the warning as-is since it correctly flags an unconfigured GPIO?
Thanks,
Marco
Signature · 2 lines
Marco Nenciarini - [email protected] 7C23 B804 3E65 D298 0A21 B6E2 589F 03F0 1BA5 5038