QCA6174 Performance
The md5sum matches.
I installed Kernel 4.8 from Ubuntu's mainline ppa to get the recent version of ath10k which increased the performance, but it's still pretty low.
Here is the output of dmesg with kernel 4.8:
dmesg | grep -i ath10k
[ 9.264413] ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 9.544276] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2 [ 9.544292] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/cal-pci-0000:02:00.0.bin failed with error -2 [ 9.546101] ath10k_pci 0000:02:00.0: qca6174 hw2.1 target 0x05010000 chip_id 0x003405ff sub 17aa:3044 [ 9.546105] ath10k_pci 0000:02:00.0: kconfig debug 0 debugfs 0 tracing 0 dfs 0 testmode 0 [ 9.547303] ath10k_pci 0000:02:00.0: firmware ver SW_RM.1.1.1-00157-QCARMSWPZ-1 api 5 features ignore-otp,no-4addr-pad crc32 10bf8e08 [ 9.613313] ath10k_pci 0000:02:00.0: board_file api 2 bmi_id N/A crc32 ae2e275a [ 10.813664] ath10k_pci 0000:02:00.0: htt-ver 3.1 wmi-op 4 htt-op 3 cal otp max-sta 32 raw 0 hwcrypto 1 [ 10.902302] ath10k_pci 0000:02:00.0 wlp2s0: renamed from wlan0 [ 26.617451] ath10k_pci 0000:02:00.0: no channel configured; ignoring frame(s)!
Daniel Holz
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
Quoted 7 lines · Daniel Holz
The md5sum matches.
I installed Kernel 4.8 from Ubuntu's mainline ppa to get the recent version of ath10k which increased the performance, but it's still pretty low.
Here is the output of dmesg with kernel 4.8:
You can check it with a recent enough iw:
iw wlp2s0 info
It should tell you channel bandwidth you are using.
Maybe ath10k or your AP has a bug that causes wrong capabilities to be negotiated during association.
You could try re-configuring your AP (to slower speeds) or force wpa_supplicant/ath10k to not use vht or ht modes at all and re-testing if it helps.
Michał
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
iw wlp2s0 info displays that my bandwidth is 80 MHz. Over the weekend I tried different configurations like using n instead of ac or 2,4 GHz and connection speed on a different WLAN, but the performance was always extremely slow.
Daniel Holz
Am Fr, 16. Sep, 2016 um 2:23 schrieb Michal Kazior <[email protected]>:
Quoted 19 lines · Daniel Holz
Quoted 9 lines
The md5sum matches.
I installed Kernel 4.8 from Ubuntu's mainline ppa to get the recent
version
of ath10k which increased the performance, but it's still pretty
low.Here is the output of dmesg with kernel 4.8:
You can check it with a recent enough iw:
iw wlp2s0 infoIt should tell you channel bandwidth you are using.
Maybe ath10k or your AP has a bug that causes wrong capabilities to be negotiated during association.
Quoted 6 lines
You could try re-configuring your AP (to slower speeds) or force wpa_supplicant/ath10k to not use vht or ht modes at all and re-testing if it helps.
Michał
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k