Skip to contentSkip to conversation

jethro 2.0.1/ubi-utils not installed on target

DISCUSSION [email protected] 3 participants 6 messages Feb 16, 2016 – Feb 18, 2016

lore
Share & tools
lore
#0 lore raw

Hi,

I would like to have ubi-utils, which is part of mtd-utils, installed on my target.

It seems to be insufficient to add mtd-utils to a packagegroup[1] and add this to the image for it to be installed in the image. The package is being built and I can install it afterwards e.g. opkg install mtd-utils-ubifs_1.5.1+git0+9f107132a6-r0_armv7a

Is it intended to be like this?

Regards,

Robert

[1] https://github.com/RobertBerger/meta-mainline/blob/jethro-training-v4.4.x/multi-v7-ml/recipes-core/packagegroups/packagegroup-tools-fs.bb

#1 lore raw
Quoted 7 lines · On 16 February 2016 at 09:03, <[email protected]> wrote:

It seems to be insufficient to add mtd-utils to a packagegroup[1] and add this to the image for it to be installed in the image.
The package is being built and I can install it afterwards e.g. opkg install mtd-utils-ubifs_1.5.1+git0+9f107132a6-r0_armv7a

Is it intended to be like this?

Yes. As you said the resulting package is called mtd-utils-ubifs, so that's the name you need to use in the packagegroup.

Ross

#2 lore raw

On 2016-02-16 05:40, Burton, Ross wrote:
Hi,

Quoted 8 lines
Quoted 5 lines · On 16 February 2016 at 09:03, <[email protected]> wrote:

It seems to be insufficient to add mtd-utils to a packagegroup[1] and add this to the image for it to be installed in the image. The package is being built and I can install it afterwards e.g. opkg install mtd-utils-ubifs_1.5.1+git0+9f107132a6-r0_armv7a

Quoted 4 lines
Quoted 1 line

Is it intended to be like this?

Yes. As you said the resulting package is called mtd-utils-ubifs, so that's the name you need to use in the packagegroup.

Thanks. I figured this out in the meantime;)

I looked into mtd-utils.bb and the packages built where I found mtd-utils-ubifs, which does not seem a very generic approach.

One recipe can result in more than one packages, so

-s, --show-versions Show current and preferred versions of all recipes.

does not show all packages.

Quoted 1 line

bitbake -s | grep mtd

core-image-minimal-mtdutils :1.0-r0
mtd-utils :1.5.1+gitAUTOINC+9f107132a6-r0
mtd-utils-native :1.5.1+gitAUTOINC+9f107132a6-r0
mtdev :1.1.5-r0

How can I get a list of all available packages? Maybe there are more hidden secrets;)

What I've found so far is[1], but still I don't get the complete list of available packages:

bb search-packages mtd
Parsing recipes..done.
Gathering preferred recipe filenames...done
core-image-minimal-mtdutils:
Packages:
core-image-minimal-mtdutils
mtd-utils-native:
Packages:
mtd-utils-native
mtd-utils:
Packages:
mtd-utils-misc
mtd-utils-doc
mtd-utils-jffs2
mtd-utils-ubifs
mtd-utils-staticdev
mtd-utils-dev
mtd-utils-locale
mtd-utils
mtd-utils-dbg
mtdev:
Packages:
mtdev-locale
mtdev-dbg
mtdev-staticdev
mtdev-doc
mtdev
mtdev-dev

[1] https://github.com/kergoth/bb

Quoted 2 lines

Ross

Regards,

Robert

#3 lore raw

Hi Robert,

Quoted 18 lines · On Wed, 17 Feb 2016 02:47:46 [email protected] wrote:
Quoted 11 lines · Ross
Quoted 6 lines · On 16 February 2016 at 09:03, <[email protected]> wrote:

It seems to be insufficient to add mtd-utils to a packagegroup[1] and add this to the image for it to be installed in the image. The package is being built and I can install it afterwards e.g. opkg install mtd-utils-ubifs_1.5.1+git0+9f107132a6-r0_armv7a

Is it intended to be like this?

Yes. As you said the resulting package is called mtd-utils-ubifs, so that's the name you need to use in the packagegroup.

Thanks. I figured this out in the meantime;)

I looked into mtd-utils.bb and the packages built where I found mtd-utils-ubifs, which does not seem a very generic approach.

Quoted 6 lines

One recipe can result in more than one packages, so

-s, --show-versions Show current and preferred versions of all
recipes.

does not show all packages.

No, because bitbake -s lists recipes, not packages.

If you want the complete list of packages you can only get it after a recipe has been built, at which time oe-pkgdata-util can be used:

$ oe-pkgdata-util list-pkgs -p mtd-utils
mtd-utils-jffs2
mtd-utils-ubifs
mtd-utils-misc
mtd-utils-dbg
mtd-utils-dev
mtd-utils-doc
mtd-utils

The reason this is only available after building (strictly speaking, after do_packagedata has executed for the recipe in question) is that often the list of packages isn't determined until then; for example, kernel module packages are completely dynamic based on those modules that are enabled.

Cheers,
Paul

PS if you wish to email me could you please use my email address rather than the gmane alias you're currently using.

Signature · 2 lines
Paul Eggleton
Intel Open Source Technology Centre
#4 lore raw

Hi,

Quoted 15 lines · Paul Eggleton

Hi Robert,

If you want the complete list of packages you can only get it after a recipe has been built, at which time oe-pkgdata-util can be used:

$ oe-pkgdata-util list-pkgs -p mtd-utils
mtd-utils-jffs2
mtd-utils-ubifs
mtd-utils-misc
mtd-utils-dbg
mtd-utils-dev
mtd-utils-doc
mtd-utils
Quoted 7 lines

The reason this is only available after building (strictly speaking, after do_packagedata has executed for the recipe in question) is that often the list of packages isn't determined until then; for example, kernel module packages are completely dynamic based on those modules that are enabled.

Cheers,
Paul

Thanks.

So would something I hacked up quickly like this work?

test.sh:
-->
bitbake -s | awk '{ print $1}' > test.txt tail -n +6 test.txt > test1.txt
while IFS='' read -r line || [[ -n "$line" ]]; do
echo "-->"
echo "oe-pkgdata-util list-pkgs -p $line" oe-pkgdata-util list-pkgs -p $line 2> /dev/null echo "<--"
done < test1.txt
<--

./test.sh | grep mtd
oe-pkgdata-util list-pkgs -p core-image-minimal-mtdutils oe-pkgdata-util list-pkgs -p mtd-utils mtd-utils-jffs2
mtd-utils-ubifs
mtd-utils-misc
mtd-utils-dbg
mtd-utils-dev
mtd-utils-doc
mtd-utils
oe-pkgdata-util list-pkgs -p mtd-utils-native oe-pkgdata-util list-pkgs -p mtdev
mtdev-dbg
mtdev-staticdev
mtdev-dev
mtdev

Quoted 3 lines

PS if you wish to email me could you please use my email address rather than the gmane alias you're currently using.

I'll try. Now I reply with your regular email (hoping gmane will not scramble it)

Regards,

Robert

#5 lore raw
Quoted 15 lines · On Wed, 17 Feb 2016 10:10:16 [email protected] wrote:
Quoted 11 lines · Paul Eggleton

If you want the complete list of packages you can only get it after a recipe has been built, at which time oe-pkgdata-util can be used:

$ oe-pkgdata-util list-pkgs -p mtd-utils
mtd-utils-jffs2
mtd-utils-ubifs
mtd-utils-misc
mtd-utils-dbg
mtd-utils-dev
mtd-utils-doc
mtd-utils

So would something I hacked up quickly like this work?

Quoted 11 lines

test.sh:
-->
bitbake -s | awk '{ print $1}' > test.txt tail -n +6 test.txt > test1.txt
while IFS='' read -r line || [[ -n "$line" ]]; do
echo "-->"
echo "oe-pkgdata-util list-pkgs -p $line" oe-pkgdata-util list-pkgs -p $line 2> /dev/null echo "<--"
done < test1.txt
<--

Well, oe-pkgdata-util list-pkgs with no arguments should list all (previously built) packages, if that's what you're after. You can also specify a wildcarded search term e.g.

oe-pkgdata-util list-pkgs '*utils*'

Cheers,
Paul

Signature · 2 lines
Paul Eggleton
Intel Open Source Technology Centre