RH-9 boot hangs from floppy bootdisk
Hi,
I have just installed RH-9 from ISO images I downloaded yesterday.
This system used to run RH-7.3 until this morning. The RH install CD ran and installed just fine, and I created a boot disk on floppy. I installed GRUB on the first partition of my RH drive, but not on the MBR.
I have 2 hard-drives, with Win-XP Pro on the first one (C:, /dev/hda) and RH (D:, /dev/hdb) on the second. I also have a DVD-ROM (E:, /dev/hdc) and a CD-RW drive (F: /dev/hdd).
When booting from floppy, it loads the kernel/ramdisk from floppy, then recognizes the HW and then hangs with the following message (at the bottom). Hitting any key causes a single "keyboard: unknown keysequence 0e .." and then I have to hard-reset to recover.
Any help would be most appreciated. Here's the console output:
.....
PIIX4: IDE controller at PCI slot 00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode, will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:dma, hdb:dma ide1: BM-DMA at oxf008-0xf00f, BIOS settings: hdc:dma, hdd:dma HPT370: IDE controller at PCI slot 00:0e.1 HPT370: chipset revision 3 HPT370: not 100% native mode, will probe irqs later ide2: BM-DMA at 0xb400-0xb407, BIOS settings: hde:pio, hdf:pio ide3: BM-DMA at oxb408-0xb40f, BIOS settings: hdg:pio, hdh:pio
hda: IC35L080AWA07-0, ATA disk drive
hdb: WDC WD200EB-00BHF0, ATA disk drive
blk: queue c03c9f40, I/O limit 4095Mb (mask 0cffffffff)
blk: queue c03c9084, I/O limit 4095Mb (mask 0cffffffff)
hdc: CREATIVEDVD1240E, ATAPI CD/DVD-ROM drive
hdd: YAMAHA CRW2200E, ATAPI CD/DVD-ROM drive <hangs right here>
Thanks,
Shash
Quoted 4 lines · Shash Chatterjee
When booting from floppy, it loads the kernel/ramdisk from floppy, then recognizes the HW and then hangs with the following message (at the bottom). Hitting any key causes a single "keyboard: unknown keysequence 0e .." and then I have to hard-reset to recover.
Firstly try booting with the additional option "ide=nodma". That will hopefully get you installed but slowly and able to update to a newer kernel.
Alan,
Thanks for the suggestion, certainly works far better than before. Disabling DMA on IDE does allow me to boot right up. I was able to use up2date and install the 2.4.20-20.9 kernel. I then made a new bootdisk using mkbootdisk. Booting using the new kernel from floppy got a bit further, it actually loaded the kernel fro /dev/hdb2. But hung after it got to "Enabling Swap ..". Any more ideas?
I am now about to copy the boot sector using dd and using Win-XP's loader to load it to see if it helps.
Should I be using an even newer kernel? Which one is known to work with RH-9 (I haven't kept up with building kernels and libc compatibilities in a long time, not since Slackware '97 days :-)?
Shash
Quoted 9 lines · Alan Cox
Quoted 1 line · Shash Chatterjee
When booting from floppy, it loads the kernel/ramdisk from floppy, then recognizes the HW and then hangs with the following message (at the bottom). Hitting any key causes a single "keyboard: unknown keysequence 0e .." and then I have to hard-reset to recover.
Firstly try booting with the additional option "ide=nodma". That will hopefully get you installed but slowly and able to update to a newer kernel.