Skip to contentSkip to conversation

2.6.0-test[56] pcnet32 problems

DISCUSSION Danny ter Haar 3 participants 5 messages Sep 30, 2003

lore
Share & tools
lore
#0 lore raw

Got an cyrix box with built in ethernet & 2 extra ethernet cards as a firewall at home with a dsl line (connected to eth0)

pcnet32.c:v1.27b 01.10.2002 [email protected]
PCI: Found IRQ 11 for device 0000:00:0f.0
IRQ routing conflict for 0000:00:0f.0, have irq 9, want irq 11
pcnet32: PCnet/FAST III 79C973 at 0xfca0, warning: CSR address invalid,
using instead PROM address of 00 00 e2 24 41 1d assigned IRQ 9.
eth0: registered as PCnet/FAST III 79C973
pcnet32: 1 cards_found.

Sometimes (even during low traffic) eth0 simply locks up:
In dmesg i see:
kernel: eth0: Bus master arbitration failure, status 88f3.

rmmod pcnet32 results in kernel-panic.
Only reboot works.
tried:
acpi == disabled
pci=noacpi

Another weird thing is output of ifconfig eth0:

eth0 Link encap:Ethernet HWaddr 00:00:E2:24:41:1D

          inet addr:195.64.94.48  Bcast:195.64.94.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:30345 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:16042 dropped:0 overruns:0 carrier:16042
          collisions:0 txqueuelen:1000 
          RX bytes:38404293 (36.6 MiB)  TX bytes:1298028 (1.2 MiB)
          Interrupt:9 Base address:0xfca0 

0 packets transmitted , all errors ans carrier faults ? Still it works! (this could be counters that are wrong)

kernel config, lspci -v and dmesg output available at:

http://dth.net/kernel/

Any help/suggestions/hints appreciated.

Danny

Signature · 4 lines
 /"\                        | Dying is to be avoided because
 \ /  ASCII RIBBON CAMPAIGN | it can ruin your whole career 
  X   against HTML MAIL     | 
 / \  and POSTINGS          | - Bob Hope
#1 lore raw
Quoted 32 lines · Danny ter Haar

Got an cyrix box with built in ethernet & 2 extra ethernet cards as a firewall at home with a dsl line (connected to eth0)

pcnet32.c:v1.27b 01.10.2002 [email protected]
PCI: Found IRQ 11 for device 0000:00:0f.0
IRQ routing conflict for 0000:00:0f.0, have irq 9, want irq 11
pcnet32: PCnet/FAST III 79C973 at 0xfca0, warning: CSR address invalid,
using instead PROM address of 00 00 e2 24 41 1d assigned IRQ 9.
eth0: registered as PCnet/FAST III 79C973
pcnet32: 1 cards_found.

Sometimes (even during low traffic) eth0 simply locks up:
In dmesg i see:
kernel: eth0: Bus master arbitration failure, status 88f3.

rmmod pcnet32 results in kernel-panic.
Only reboot works.
tried:
acpi == disabled
pci=noacpi

Another weird thing is output of ifconfig eth0:

eth0 Link encap:Ethernet HWaddr 00:00:E2:24:41:1D

          inet addr:195.64.94.48  Bcast:195.64.94.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:30345 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:16042 dropped:0 overruns:0 carrier:16042
          collisions:0 txqueuelen:1000 
          RX bytes:38404293 (36.6 MiB)  TX bytes:1298028 (1.2 MiB)
          Interrupt:9 Base address:0xfca0 
Quoted 8 lines

0 packets transmitted , all errors ans carrier faults ? Still it works! (this could be counters that are wrong)

kernel config, lspci -v and dmesg output available at:

http://dth.net/kernel/

Any help/suggestions/hints appreciated.

Upgrade ifconfig?

Signature · 2 lines
Vojtech Pavlik
SuSE Labs, SuSE CR
#2 lore raw
Quoted 1 line · Vojtech Pavlik

Upgrade ifconfig?

Latest unstable debian.
The other 2 network cards (eepro/8139too) do work/show ok.

Danny

Signature · 4 lines
 /"\                        | Dying is to be avoided because
 \ /  ASCII RIBBON CAMPAIGN | it can ruin your whole career 
  X   against HTML MAIL     | 
 / \  and POSTINGS          | - Bob Hope
#3 lore raw
In reply to Danny ter Haar
Quoted 3 lines · Danny ter Haar

Sometimes (even during low traffic) eth0 simply locks up:
In dmesg i see:
kernel: eth0: Bus master arbitration failure, status 88f3.

Hmmm... I'm not seeing this at all.

If going back to an older kernel gets rid of this problem, perhaps it could be an IRQ routing problem or something like that. That's just a guess, however. (If it doesn't, I would suspect hardware failure, perhaps your motherboard; motherboard failures are the only time I've seen this message happen with pcnet32 cards.)

Quoted 1 line

rmmod pcnet32 results in kernel-panic.

I never tried that because my primary pcnet32-using machine runs monolithic kernels...

-Barry K. Nathan <[email protected]>

#4 lore raw
Quoted 2 lines · Barry K. Nathan

If going back to an older kernel gets rid of this problem, perhaps it could be an IRQ routing problem or something like that.

I will try first a monolithic kernel
If that doesn't work i'll change it for a 2.4.23-preXX

Quoted 4 lines

That's just a
guess, however. (If it doesn't, I would suspect hardware failure, perhaps your motherboard; motherboard failures are the only time I've seen this message happen with pcnet32 cards.)

Last weekend i exchanged my old (but stable) pentium 75Mhz to the cyrix setup which happens to be a prototype of a siemens settop box. (ir keyboard, tv-out and DVB card).
It could be faulty motherboard but it doesn't happen if transfer huge amounts of data over the other two ethernet cards.

Thank for your answer(s)

Danny

Signature · 4 lines
 /"\                        | Dying is to be avoided because
 \ /  ASCII RIBBON CAMPAIGN | it can ruin your whole career 
  X   against HTML MAIL     | 
 / \  and POSTINGS          | - Bob Hope