sym53c8xx scsi errors
I was hoping someone might be able to explain the cause of the two scsi errors at the end of this log output. These errors occured at boot, but I haven't seen any other errors. System appears to be working fine otherwise, but I'm concerned.
Linux kernel version 2.4.22.
Thanks!
- Orion
Dec 10 17:43:04 saga kernel: sym.4.3.0: setting PCI_COMMAND_PARITY... Dec 10 17:43:04 saga kernel: sym.4.3.1: setting PCI_COMMAND_PARITY... Dec 10 17:43:04 saga kernel: sym0: <1010-33> rev 0x1 on pci bus 4 device 3 function 0 irq 18 Dec 10 17:43:04 saga kernel: sym0: using 64 bit DMA addressing Dec 10 17:43:04 saga kernel: sym0: Symbios NVRAM, ID 7, Fast-80, LVD, parity checking Dec 10 17:43:04 saga kernel: sym0: open drain IRQ line driver, using on-chip SRAM Dec 10 17:43:04 saga kernel: sym0: using LOAD/STORE-based firmware. Dec 10 17:43:04 saga kernel: sym0: handling phase mismatch from SCRIPTS. Dec 10 17:43:04 saga kernel: sym0: SCSI BUS has been reset. Dec 10 17:43:04 saga kernel: sym1: <1010-33> rev 0x1 on pci bus 4 device 3 function 1 irq 18 Dec 10 17:43:04 saga kernel: sym1: using 64 bit DMA addressing Dec 10 17:43:04 saga kernel: sym1: Symbios NVRAM, ID 7, Fast-80, SE, parity checking Dec 10 17:43:04 saga kernel: sym1: open drain IRQ line driver, using on-chip SRAM Dec 10 17:43:04 saga kernel: sym1: using LOAD/STORE-based firmware. Dec 10 17:43:04 saga kernel: sym1: handling phase mismatch from SCRIPTS. Dec 10 17:43:04 saga kernel: sym1: SCSI BUS has been reset. Dec 10 17:43:04 saga kernel: scsi2 : sym-2.1.17a Dec 10 17:43:04 saga kernel: scsi3 : sym-2.1.17a Dec 10 17:43:05 saga kernel: sym0:0:0: tagged command queuing enabled, command queue depth 16. Dec 10 17:43:05 saga kernel: sym0:1:0: tagged command queuing enabled, command queue depth 16. Dec 10 17:43:05 saga kernel: sym0:2:0: tagged command queuing enabled, command queue depth 16. Dec 10 17:43:05 saga kernel: sym0:3:0: tagged command queuing enabled, command queue depth 16. Dec 10 17:43:05 saga kernel: sym0:8:0: tagged command queuing enabled, command queue depth 16. Dec 10 17:43:05 saga kernel: sym0:9:0: tagged command queuing enabled, command queue depth 16. Dec 10 17:43:05 saga kernel: sym0:0: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 15) Dec 10 17:43:05 saga kernel: sym0:1: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 31) Dec 10 17:43:05 saga kernel: sym0:2: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 31) Dec 10 17:43:05 saga kernel: sym0:3: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 15) Dec 10 17:43:05 saga kernel: sym0:8: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 31) Dec 10 17:43:05 saga kernel: sym0:9: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 31) Dec 10 17:43:05 saga kernel: sym53c8xx: at PCI bus 4, device 3, function 0 Dec 10 17:43:05 saga kernel: sym53c8xx: IO region 0x4000[0..127] is in use Dec 10 17:43:05 saga kernel: sym0:9: ERROR (0:8) (0-0-0) (1f/38/0) @ (scripta 3c0:50000000). Dec 10 17:43:05 saga kernel: sym0: script cmd = 80000000 Dec 10 17:43:05 saga kernel: sym0: regdump: da 00 00 38 47 1f 09 0f 04 08 89 00 80 00 0f 0a ff 10 46 37 02 00 00 00. Dec 10 17:43:05 saga kernel: sym53c8xx: at PCI bus 4, device 3, function 1 Dec 10 17:43:05 saga kernel: sym53c8xx: IO region 0x4400[0..127] is in use Dec 10 17:43:05 saga kernel: sym0: SCSI BUS reset detected. Dec 10 17:43:05 saga kernel: sym0: SCSI BUS has been reset. Dec 10 17:43:05 saga kernel: sym1:15: ERROR (0:8) (0-0-0) (0/0/0) @ (scripta 3c0:50000000). Dec 10 17:43:05 saga kernel: sym1: script cmd = 80000000 Dec 10 17:43:05 saga kernel: sym1: regdump: da 00 00 00 47 00 0f 0f 00 08 00 00 80 00 08 0a ff c0 45 37 00 00 00 00. Dec 10 17:43:05 saga kernel: sym1: SCSI BUS reset detected. Dec 10 17:43:05 saga kernel: sym1: SCSI BUS has been reset.