Skip to contentSkip to conversation

New: AIC79xx is not working properly with an attached scsi tape since 2.6.29

Bug 14159 [email protected] 3 participants 24 messages Sep 11, 2009 – Sep 17, 2009

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

http://bugzilla.kernel.org/show_bug.cgi?id=14159

           Summary: AIC79xx is not working properly with an attached scsi
                    tape since 2.6.29
           Product: SCSI Drivers
           Version: 2.5
    Kernel Version: 2.6.27 (working), 2.6.30 (not working)
          Platform: All
        OS/Version: Linux
              Tree: Mainline
            Status: NEW
          Severity: normal
          Priority: P1
         Component: Other
        AssignedTo: [email protected]
        ReportedBy: [email protected]
                CC: [email protected]
        Regression: Yes

Both kernels 2.6.27 and 2.6.28 are working correctly. Since Linux 2.6.29 till 2.6.31rc8 the regression(?) is out there.

Please let me know if I can provide any further details.

Best regards,
Gabriele

=================
Here is the messages part for Linux 2.6.27:

aic79xx 0000:41:01.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 scsi5 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
<Adaptec 29320ALP PCIx Ultra320 SCSI adapter>
aic7901: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs
target5:0:3: asynchronous
scsi 5:0:3:0: Sequential-Access IBM HH LTO Gen 2 0376 PQ: 0 ANSI: 3
target5:0:3: Beginning Domain Validation
target5:0:3: wide asynchronous
target5:0:3: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 126) target5:0:3: Ending Domain Validation
scsi 5:0:3:0: Attached scsi generic sg7 type 1
st: Version 20080504, fixed bufsize 32768, s/g segs 256
Driver 'st' needs updating - please use bus_type methods
st 5:0:3:0: Attached scsi tape st0
st 5:0:3:0: st0: try direct i/o: yes (alignment 4 B)
osst :I: Tape driver with OnStream support version 0.99.4
osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $ Driver 'osst' needs updating - please use bus_type methods
st0: Block limits 256 - 524288 bytes.
=================

=================
Here is Linux 2.6.30:

Aug  3 06:25:04 svil kernel: aic79xx 0000:41:01.0: PCI INT A -> GSI 19 (level,
low) -> IRQ 19
Aug  3 06:25:04 svil kernel: scsi5 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev
3.0
Aug  3 06:25:04 svil kernel:         <Adaptec 29320ALP PCIx Ultra320 SCSI
adapter>
Aug  3 06:25:04 svil kernel:         aic7901: Ultra320 Wide Channel A, SCSI
Id=7, PCI-X 101-1
Aug  3 06:25:04 svil kernel: scsi 5:0:0:0: Attempting to queue an ABORT
message:CDB: 0x12 0x0
Aug  3 06:25:04 svil kernel: scsi 5:0:0:0: Command already completed
Aug  3 06:25:04 svil kernel: scsi 5:0:0:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 
Aug  3 06:25:04 svil kernel: scsi 5:0:0:0: Command already completed
Aug  3 06:25:04 svil kernel: scsi 5:0:0:0: Attempting to queue a TARGET RESET
message:CDB: 0x
Aug  3 06:25:04 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:04 svil kernel: scsi5: Device reset timer expired (active 1)
Aug  3 06:25:04 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:04 svil kernel: Recovery SCB completes
Aug  3 06:25:04 svil kernel: scsi 5:0:0:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 
Aug  3 06:25:04 svil kernel: scsi 5:0:0:0: Command already completed
Aug  3 06:25:04 svil kernel: scsi 5:0:0:0: Device offlined - not ready after
error recovery
Aug  3 06:25:04 svil kernel: scsi 5:0:1:0: Attempting to queue an ABORT
message:CDB: 0x12 0x0
Aug  3 06:25:04 svil kernel: scsi 5:0:1:0: Command already completed
Aug  3 06:25:04 svil kernel: scsi 5:0:1:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 
Aug  3 06:25:04 svil kernel: scsi 5:0:1:0: Command already completed
Aug  3 06:25:04 svil kernel: scsi 5:0:1:0: Attempting to queue a TARGET RESET
message:CDB: 0x
Aug  3 06:25:04 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:04 svil kernel: scsi5: Device reset timer expired (active 1)
Aug  3 06:25:04 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:04 svil kernel: Recovery SCB completes
Aug  3 06:25:04 svil kernel: scsi 5:0:1:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 
Aug  3 06:25:04 svil kernel: scsi 5:0:1:0: Command already completed
Aug  3 06:25:04 svil kernel: scsi 5:0:1:0: Device offlined - not ready after
error recovery
Aug  3 06:25:04 svil kernel: scsi 5:0:2:0: Attempting to queue an ABORT
message:CDB: 0x12 0x0
Aug  3 06:25:04 svil kernel: scsi 5:0:2:0: Command already completed
Aug  3 06:25:04 svil kernel: scsi 5:0:2:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 
Aug  3 06:25:04 svil kernel: scsi 5:0:2:0: Command already completed
Aug  3 06:25:04 svil kernel: scsi 5:0:2:0: Attempting to queue a TARGET RESET
message:CDB: 0x
Aug  3 06:25:04 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:04 svil kernel: scsi5: Device reset timer expired (active 1)
Aug  3 06:25:05 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:05 svil kernel: Recovery SCB completes
Aug  3 06:25:05 svil kernel: scsi 5:0:2:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 
Aug  3 06:25:05 svil kernel: scsi 5:0:2:0: Command already completed
Aug  3 06:25:05 svil kernel: scsi 5:0:2:0: Device offlined - not ready after
error recovery
Aug  3 06:25:05 svil kernel: scsi 5:0:3:0: Attempting to queue an ABORT
message:CDB: 0x12 0x0
Aug  3 06:25:05 svil kernel: scsi5: At time of recovery, card was paused
Aug  3 06:25:05 svil kernel: >>>>>>>>>>>>>>>>>> Dump Card State Begins
<<<<<<<<<<<<<<<<<
Aug  3 06:25:05 svil kernel: scsi5: Dumping Card State at program address 0x127
Mode 0x11
Aug  3 06:25:05 svil kernel: Card was paused
Aug  3 06:25:05 svil kernel: INTSTAT[0x0] SELOID[0x3] SELID[0x0]
HS_MAILBOX[0x0]
Aug  3 06:25:05 svil kernel: INTCTL[0x0] SEQINTSTAT[0x0] SAVED_MODE[0x0]
DFFSTAT[0x19]
Aug  3 06:25:05 svil kernel: SCSISIGI[0xe6] SCSIPHASE[0x8] SCSIBUS[0x2]
LASTPHASE[0xe0]
Aug  3 06:25:05 svil kernel: SCSISEQ0[0x0] SCSISEQ1[0x12] SEQCTL0[0x0]
SEQINTCTL[0x0]
Aug  3 06:25:05 svil kernel: SEQ_FLAGS[0x0] SEQ_FLAGS2[0x4] QFREEZE_COUNT[0x0]
Aug  3 06:25:05 svil kernel: KERNEL_QFREEZE_COUNT[0x0] MK_MESSAGE_SCB[0xff00]
Aug  3 06:25:05 svil kernel: MK_MESSAGE_SCSIID[0xff] SSTAT0[0x2] SSTAT1[0x1]
Aug  3 06:25:05 svil kernel: SSTAT2[0x0] SSTAT3[0x0] PERRDIAG[0x0]
SIMODE1[0xac]
Aug  3 06:25:05 svil kernel: LQISTAT0[0x0] LQISTAT1[0x0] LQISTAT2[0x0]
LQOSTAT0[0x0]
Aug  3 06:25:05 svil kernel: LQOSTAT1[0x0] LQOSTAT2[0x0]
Aug  3 06:25:05 svil kernel:
Aug  3 06:25:05 svil kernel: SCB Count = 4 CMDS_PENDING = 1 LASTSCB 0xffff
CURRSCB 0x3 NEXTSC
Aug  3 06:25:05 svil kernel: qinstart = 13 qinfifonext = 13
Aug  3 06:25:05 svil kernel: QINFIFO:
Aug  3 06:25:05 svil kernel: WAITING_TID_QUEUES:
Aug  3 06:25:05 svil kernel: Pending list:
Aug  3 06:25:05 svil kernel:   3 FIFO_USE[0x0] SCB_CONTROL[0x40]
SCB_SCSIID[0x37]
Aug  3 06:25:05 svil kernel: Total 1
Aug  3 06:25:05 svil kernel: Kernel Free SCB list: 2 1 0
Aug  3 06:25:05 svil kernel: Sequencer Complete DMA-inprog list:
Aug  3 06:25:05 svil kernel: Sequencer Complete list:
Aug  3 06:25:05 svil kernel: Sequencer DMA-Up and Complete list:
Aug  3 06:25:05 svil kernel: Sequencer On QFreeze and Complete list:
Aug  3 06:25:05 svil kernel:
Aug  3 06:25:05 svil kernel:
Aug  3 06:25:05 svil kernel: scsi5: FIFO0 Free, LONGJMP == 0x80ff, SCB 0x0
Aug  3 06:25:05 svil kernel: SEQIMODE[0x3f] SEQINTSRC[0x0] DFCNTRL[0x0]
DFSTATUS[0x89]
Aug  3 06:25:05 svil kernel: SG_CACHE_SHADOW[0x2] SG_STATE[0x0] DFFSXFRCTL[0x0]
Aug  3 06:25:05 svil kernel: SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR = 0x00, SHCNT =
0x0
Aug  3 06:25:05 svil kernel: HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]
Aug  3 06:25:05 svil kernel:
Aug  3 06:25:05 svil kernel: scsi5: FIFO1 Active, LONGJMP == 0x8063, SCB 0x3
Aug  3 06:25:05 svil kernel: SEQIMODE[0x3f] SEQINTSRC[0x0] DFCNTRL[0x4]
DFSTATUS[0x89]
Aug  3 06:25:05 svil kernel: SG_CACHE_SHADOW[0x2] SG_STATE[0x0] DFFSXFRCTL[0x0]
Aug  3 06:25:05 svil kernel: SOFFCNT[0x0] MDFFSTAT[0x14] SHADDR = 0x06, SHCNT =
0x0
Aug  3 06:25:05 svil kernel: HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]
Aug  3 06:25:05 svil kernel: LQIN: 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
0x0 0x0 0x0 0x
Aug  3 06:25:05 svil kernel: scsi5: LQISTATE = 0x0, LQOSTATE = 0x0, OPTIONMODE
= 0x52
Aug  3 06:25:05 svil kernel: scsi5: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x0
Aug  3 06:25:05 svil kernel: scsi5: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
Aug  3 06:25:05 svil kernel: SIMODE0[0xc]
Aug  3 06:25:05 svil kernel: CCSCBCTL[0x4]
Aug  3 06:25:05 svil kernel: scsi5: REG0 == 0x3, SINDEX = 0x1e0, DINDEX = 0xe1
Aug  3 06:25:05 svil kernel: scsi5: SCBPTR == 0x3, SCB_NEXT == 0xffc0,
SCB_NEXT2 == 0xff65
Aug  3 06:25:05 svil kernel: CDB 12 0 0 0 24 0
Aug  3 06:25:05 svil kernel: STACK: 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:05 svil kernel: <<<<<<<<<<<<<<<<< Dump Card State Ends
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Aug  3 06:25:05 svil kernel: scsi 5:0:3:0: Device is active, asserting ATN
Aug  3 06:25:05 svil kernel: scsi5: Recovery code sleeping
Aug  3 06:25:05 svil kernel: scsi5: Timer Expired (active 1)
Aug  3 06:25:05 svil kernel: Recovery code awake
Aug  3 06:25:05 svil kernel: scsi5: Command abort returning 0x2003
Aug  3 06:25:06 svil kernel: scsi 5:0:3:0: Attempting to queue a TARGET RESET
message:CDB: 0x
Aug  3 06:25:06 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:06 svil kernel: scsi5: Device reset timer expired (active 2)
Aug  3 06:25:06 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:06 svil kernel: Recovery SCB completes
Aug  3 06:25:06 svil kernel: Recovery SCB completes
Aug  3 06:25:06 svil kernel: scsi 5:0:3:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 
Aug  3 06:25:06 svil kernel: scsi5: At time of recovery, card was not paused
Aug  3 06:25:06 svil kernel: >>>>>>>>>>>>>>>>>> Dump Card State Begins
<<<<<<<<<<<<<<<<<
Aug  3 06:25:06 svil kernel: scsi5: Dumping Card State at program address 0x34
Mode 0x22
Aug  3 06:25:06 svil kernel: Card was paused
Aug  3 06:25:06 svil kernel: INTSTAT[0x0] SELOID[0x3] SELID[0x0]
HS_MAILBOX[0x0]
Aug  3 06:25:06 svil kernel: INTCTL[0x80] SEQINTSTAT[0x0] SAVED_MODE[0x0]
DFFSTAT[0x33]
Aug  3 06:25:06 svil kernel: SCSISIGI[0x0] SCSIPHASE[0x0] SCSIBUS[0x0]
LASTPHASE[0x1]
Aug  3 06:25:06 svil kernel: SCSISEQ0[0x0] SCSISEQ1[0x12] SEQCTL0[0x0]
SEQINTCTL[0x0]
Aug  3 06:25:06 svil kernel: SEQ_FLAGS[0xc0] SEQ_FLAGS2[0x4] QFREEZE_COUNT[0x1]
Aug  3 06:25:06 svil kernel: KERNEL_QFREEZE_COUNT[0x1] MK_MESSAGE_SCB[0xff00]
Aug  3 06:25:06 svil kernel: MK_MESSAGE_SCSIID[0xff] SSTAT0[0x0] SSTAT1[0x8]
Aug  3 06:25:06 svil kernel: SSTAT2[0x0] SSTAT3[0x0] PERRDIAG[0x0]
SIMODE1[0xa4]
Aug  3 06:25:06 svil kernel: LQISTAT0[0x0] LQISTAT1[0x0] LQISTAT2[0x0]
LQOSTAT0[0x0]
Aug  3 06:25:06 svil kernel: LQOSTAT1[0x0] LQOSTAT2[0x0]
Aug  3 06:25:06 svil kernel:
Aug  3 06:25:06 svil kernel: SCB Count = 4 CMDS_PENDING = 0 LASTSCB 0xffff
CURRSCB 0x3 NEXTSC
Aug  3 06:25:06 svil kernel: qinstart = 14 qinfifonext = 15
Aug  3 06:25:06 svil kernel: QINFIFO: 0x3
Aug  3 06:25:06 svil kernel: WAITING_TID_QUEUES:
Aug  3 06:25:06 svil kernel: Pending list:
Aug  3 06:25:06 svil kernel:   3 FIFO_USE[0x3] SCB_CONTROL[0x48]
SCB_SCSIID[0x37]
Aug  3 06:25:06 svil kernel: Total 1
Aug  3 06:25:06 svil kernel: Kernel Free SCB list: 2 1 0
Aug  3 06:25:06 svil kernel: Sequencer Complete DMA-inprog list:
Aug  3 06:25:06 svil kernel: Sequencer Complete list:
Aug  3 06:25:06 svil kernel: Sequencer DMA-Up and Complete list:
Aug  3 06:25:06 svil kernel: Sequencer On QFreeze and Complete list:
Aug  3 06:25:06 svil kernel:
Aug  3 06:25:06 svil kernel:
Aug  3 06:25:06 svil kernel: scsi5: FIFO0 Free, LONGJMP == 0x80ff, SCB 0x0
Aug  3 06:25:06 svil kernel: SEQIMODE[0x3f] SEQINTSRC[0x0] DFCNTRL[0x0]
DFSTATUS[0x89]
Aug  3 06:25:06 svil kernel: SG_CACHE_SHADOW[0x2] SG_STATE[0x0] DFFSXFRCTL[0x0]
Aug  3 06:25:06 svil kernel: SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR = 0x00, SHCNT =
0x0
Aug  3 06:25:06 svil kernel: HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]
Aug  3 06:25:06 svil kernel:
Aug  3 06:25:06 svil kernel: scsi5: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
Aug  3 06:25:06 svil kernel: SEQIMODE[0x3f] SEQINTSRC[0x0] DFCNTRL[0x4]
DFSTATUS[0x89]
Aug  3 06:25:06 svil kernel: SG_CACHE_SHADOW[0x2] SG_STATE[0x0] DFFSXFRCTL[0x0]
Aug  3 06:25:06 svil kernel: SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR = 0x00, SHCNT =
0x0
Aug  3 06:25:06 svil kernel: HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]
Aug  3 06:25:06 svil kernel: LQIN: 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
0x0 0x0 0x0 0x
Aug  3 06:25:06 svil kernel: scsi5: LQISTATE = 0x0, LQOSTATE = 0x0, OPTIONMODE
= 0x52
Aug  3 06:25:06 svil kernel: scsi5: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x0
Aug  3 06:25:06 svil kernel: scsi5: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
Aug  3 06:25:06 svil kernel: SIMODE0[0xc]
Aug  3 06:25:06 svil kernel: CCSCBCTL[0x0]
Aug  3 06:25:06 svil kernel: scsi5: REG0 == 0x3, SINDEX = 0x119, DINDEX = 0xe1
Aug  3 06:25:06 svil kernel: scsi5: SCBPTR == 0x3, SCB_NEXT == 0xff00,
SCB_NEXT2 == 0xffa4
Aug  3 06:25:06 svil kernel: CDB 0 0 0 0 0 0
Aug  3 06:25:06 svil kernel: STACK: 0x20 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:06 svil kernel: <<<<<<<<<<<<<<<<< Dump Card State Ends
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Aug  3 06:25:06 svil kernel: scsi5:0:3:0: Cmd aborted from QINFIFO
Aug  3 06:25:06 svil kernel: scsi 5:0:3:0: Device offlined - not ready after
error recovery
Aug  3 06:25:06 svil kernel: scsi 5:0:4:0: Attempting to queue an ABORT
message:CDB: 0x12 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:4:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:4:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 
Aug  3 06:25:06 svil kernel: scsi 5:0:4:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:4:0: Attempting to queue a TARGET RESET
message:CDB: 0x
Aug  3 06:25:06 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:06 svil kernel: scsi5: Device reset timer expired (active 1)
Aug  3 06:25:06 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:06 svil kernel: Recovery SCB completes
Aug  3 06:25:06 svil kernel: scsi 5:0:4:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 
Aug  3 06:25:06 svil kernel: scsi 5:0:4:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:4:0: Device offlined - not ready after
error recovery
Aug  3 06:25:06 svil kernel: scsi 5:0:5:0: Attempting to queue an ABORT
message:CDB: 0x12 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:5:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:5:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 
Aug  3 06:25:06 svil kernel: scsi 5:0:5:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:5:0: Attempting to queue a TARGET RESET
message:CDB: 0x
Aug  3 06:25:06 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:06 svil kernel: scsi5: Device reset timer expired (active 1)
Aug  3 06:25:06 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:06 svil kernel: Recovery SCB completes
Aug  3 06:25:06 svil kernel: scsi 5:0:5:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 
Aug  3 06:25:06 svil kernel: scsi 5:0:5:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:5:0: Device offlined - not ready after
error recovery
Aug  3 06:25:06 svil kernel: scsi 5:0:6:0: Attempting to queue an ABORT
message:CDB: 0x12 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:6:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:6:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 
Aug  3 06:25:06 svil kernel: scsi 5:0:6:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:6:0: Attempting to queue a TARGET RESET
message:CDB: 0x
Aug  3 06:25:06 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:06 svil kernel: scsi5: Device reset timer expired (active 1)
Aug  3 06:25:06 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:06 svil kernel: Recovery SCB completes
Aug  3 06:25:06 svil kernel: scsi 5:0:6:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 
Aug  3 06:25:06 svil kernel: scsi 5:0:6:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:6:0: Device offlined - not ready after
error recovery
Aug  3 06:25:06 svil kernel: scsi 5:0:8:0: Attempting to queue an ABORT
message:CDB: 0x12 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:8:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:8:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 
Aug  3 06:25:06 svil kernel: scsi 5:0:8:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:8:0: Attempting to queue a TARGET RESET
message:CDB: 0x
Aug  3 06:25:06 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:06 svil kernel: scsi5: Device reset timer expired (active 1)
Aug  3 06:25:06 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:06 svil kernel: Recovery SCB completes
Aug  3 06:25:06 svil kernel: scsi 5:0:8:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 
Aug  3 06:25:06 svil kernel: scsi 5:0:8:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:8:0: Device offlined - not ready after
error recovery
Aug  3 06:25:06 svil kernel: scsi 5:0:9:0: Attempting to queue an ABORT
message:CDB: 0x12 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:9:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:9:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 
Aug  3 06:25:06 svil kernel: scsi 5:0:9:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:9:0: Attempting to queue a TARGET RESET
message:CDB: 0x
Aug  3 06:25:06 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:06 svil kernel: scsi5: Device reset timer expired (active 1)
Aug  3 06:25:06 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:06 svil kernel: Recovery SCB completes
Aug  3 06:25:06 svil kernel: scsi 5:0:9:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 
Aug  3 06:25:06 svil kernel: scsi 5:0:9:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:9:0: Device offlined - not ready after
error recovery
Aug  3 06:25:06 svil kernel: scsi 5:0:10:0: Attempting to queue an ABORT
message:CDB: 0x12 0x
Aug  3 06:25:06 svil kernel: scsi 5:0:10:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:10:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:10:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:10:0: Attempting to queue a TARGET RESET
message:CDB: 0
Aug  3 06:25:06 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:06 svil kernel: scsi5: Device reset timer expired (active 1)
Aug  3 06:25:06 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:06 svil kernel: Recovery SCB completes
Aug  3 06:25:06 svil kernel: scsi 5:0:10:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:10:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:10:0: Device offlined - not ready after
error recovery
Aug  3 06:25:06 svil kernel: scsi 5:0:11:0: Attempting to queue an ABORT
message:CDB: 0x12 0x
Aug  3 06:25:06 svil kernel: scsi 5:0:11:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:11:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:11:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:11:0: Attempting to queue a TARGET RESET
message:CDB: 0
Aug  3 06:25:06 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:06 svil kernel: scsi5: Device reset timer expired (active 1)
Aug  3 06:25:06 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:06 svil kernel: Recovery SCB completes
Aug  3 06:25:06 svil kernel: scsi 5:0:11:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:11:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:11:0: Device offlined - not ready after
error recovery
Aug  3 06:25:06 svil kernel: scsi 5:0:12:0: Attempting to queue an ABORT
message:CDB: 0x12 0x
Aug  3 06:25:06 svil kernel: scsi 5:0:12:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:12:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:12:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:12:0: Attempting to queue a TARGET RESET
message:CDB: 0
Aug  3 06:25:06 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:06 svil kernel: scsi5: Device reset timer expired (active 1)
Aug  3 06:25:06 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:06 svil kernel: Recovery SCB completes
Aug  3 06:25:06 svil kernel: scsi 5:0:12:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:12:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:12:0: Device offlined - not ready after
error recovery
Aug  3 06:25:06 svil kernel: scsi 5:0:13:0: Attempting to queue an ABORT
message:CDB: 0x12 0x
Aug  3 06:25:06 svil kernel: scsi 5:0:13:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:13:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:13:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:13:0: Attempting to queue a TARGET RESET
message:CDB: 0
Aug  3 06:25:06 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:06 svil kernel: scsi5: Device reset timer expired (active 1)
Aug  3 06:25:06 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:06 svil kernel: Recovery SCB completes
Aug  3 06:25:06 svil kernel: scsi 5:0:13:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:13:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:13:0: Device offlined - not ready after
error recovery
Aug  3 06:25:06 svil kernel: scsi 5:0:14:0: Attempting to queue an ABORT
message:CDB: 0x12 0x
Aug  3 06:25:06 svil kernel: scsi 5:0:14:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:14:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:14:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:14:0: Attempting to queue a TARGET RESET
message:CDB: 0
Aug  3 06:25:06 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:07 svil kernel: scsi5: Device reset timer expired (active 1)
Aug  3 06:25:07 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:07 svil kernel: Recovery SCB completes
Aug  3 06:25:07 svil kernel: scsi 5:0:14:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0
Aug  3 06:25:07 svil kernel: scsi 5:0:14:0: Command already completed
Aug  3 06:25:07 svil kernel: scsi 5:0:14:0: Device offlined - not ready after
error recovery
Aug  3 06:25:07 svil kernel: scsi 5:0:15:0: Attempting to queue an ABORT
message:CDB: 0x12 0x
Aug  3 06:25:07 svil kernel: scsi 5:0:15:0: Command already completed
Aug  3 06:25:07 svil kernel: scsi 5:0:15:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0
Aug  3 06:25:07 svil kernel: scsi 5:0:15:0: Command already completed
Aug  3 06:25:07 svil kernel: scsi 5:0:15:0: Attempting to queue a TARGET RESET
message:CDB: 0
Aug  3 06:25:07 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:07 svil kernel: scsi5: Device reset timer expired (active 1)
Aug  3 06:25:07 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:07 svil kernel: Recovery SCB completes
Aug  3 06:25:07 svil kernel: scsi 5:0:15:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0
Aug  3 06:25:07 svil kernel: scsi 5:0:15:0: Command already completed
Aug  3 06:25:07 svil kernel: scsi 5:0:15:0: Device offlined - not ready after

error recovery
=================

Signature · 3 lines
Configure bugmail: http://bugzilla.kernel.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are watching the assignee of the bug.
#1 lore raw

[Bug 14159] AIC79xx is not working properly with an attached scsi tape since 2.6.29

http://bugzilla.kernel.org/show_bug.cgi?id=14159

[email protected] changed:

What |Removed |Added
----------------------------------------------------------------------------
Platform|All |i386

--- Comment #1 from [email protected] 2009-09-11 09:23:40 --- Previous log for kernel 2.6.30 was missing characters because of a cut/paste problem with text wrap, repasting :

Kernel 2.6.30

Aug  3 06:25:04 svil kernel: aic79xx 0000:41:01.0: PCI INT A -> GSI 19 (level,
low) -> IRQ 19
Aug  3 06:25:04 svil kernel: scsi5 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev
3.0
Aug  3 06:25:04 svil kernel:         <Adaptec 29320ALP PCIx Ultra320 SCSI
adapter>
Aug  3 06:25:04 svil kernel:         aic7901: Ultra320 Wide Channel A, SCSI
Id=7, PCI-X 101-133MHz, 512 SCBs
Aug  3 06:25:04 svil kernel: scsi 5:0:0:0: Attempting to queue an ABORT
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:04 svil kernel: scsi 5:0:0:0: Command already completed
Aug  3 06:25:04 svil kernel: scsi 5:0:0:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:04 svil kernel: scsi 5:0:0:0: Command already completed
Aug  3 06:25:04 svil kernel: scsi 5:0:0:0: Attempting to queue a TARGET RESET
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:04 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:04 svil kernel: scsi5: Device reset timer expired (active 1)
Aug  3 06:25:04 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:04 svil kernel: Recovery SCB completes
Aug  3 06:25:04 svil kernel: scsi 5:0:0:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:04 svil kernel: scsi 5:0:0:0: Command already completed
Aug  3 06:25:04 svil kernel: scsi 5:0:0:0: Device offlined - not ready after
error recovery
Aug  3 06:25:04 svil kernel: scsi 5:0:1:0: Attempting to queue an ABORT
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:04 svil kernel: scsi 5:0:1:0: Command already completed
Aug  3 06:25:04 svil kernel: scsi 5:0:1:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:04 svil kernel: scsi 5:0:1:0: Command already completed
Aug  3 06:25:04 svil kernel: scsi 5:0:1:0: Attempting to queue a TARGET RESET
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:04 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:04 svil kernel: scsi5: Device reset timer expired (active 1)
Aug  3 06:25:04 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:04 svil kernel: Recovery SCB completes
Aug  3 06:25:04 svil kernel: scsi 5:0:1:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:04 svil kernel: scsi 5:0:1:0: Command already completed
Aug  3 06:25:04 svil kernel: scsi 5:0:1:0: Device offlined - not ready after
error recovery
Aug  3 06:25:04 svil kernel: scsi 5:0:2:0: Attempting to queue an ABORT
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:04 svil kernel: scsi 5:0:2:0: Command already completed
Aug  3 06:25:04 svil kernel: scsi 5:0:2:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:04 svil kernel: scsi 5:0:2:0: Command already completed
Aug  3 06:25:04 svil kernel: scsi 5:0:2:0: Attempting to queue a TARGET RESET
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:04 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:04 svil kernel: scsi5: Device reset timer expired (active 1)
Aug  3 06:25:05 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:05 svil kernel: Recovery SCB completes
Aug  3 06:25:05 svil kernel: scsi 5:0:2:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:05 svil kernel: scsi 5:0:2:0: Command already completed
Aug  3 06:25:05 svil kernel: scsi 5:0:2:0: Device offlined - not ready after
error recovery
Aug  3 06:25:05 svil kernel: scsi 5:0:3:0: Attempting to queue an ABORT
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:05 svil kernel: scsi5: At time of recovery, card was paused
Aug  3 06:25:05 svil kernel: >>>>>>>>>>>>>>>>>> Dump Card State Begins
<<<<<<<<<<<<<<<<<
Aug  3 06:25:05 svil kernel: scsi5: Dumping Card State at program address 0x127
Mode 0x11
Aug  3 06:25:05 svil kernel: Card was paused
Aug  3 06:25:05 svil kernel: INTSTAT[0x0] SELOID[0x3] SELID[0x0]
HS_MAILBOX[0x0]
Aug  3 06:25:05 svil kernel: INTCTL[0x0] SEQINTSTAT[0x0] SAVED_MODE[0x0]
DFFSTAT[0x19]
Aug  3 06:25:05 svil kernel: SCSISIGI[0xe6] SCSIPHASE[0x8] SCSIBUS[0x2]
LASTPHASE[0xe0]
Aug  3 06:25:05 svil kernel: SCSISEQ0[0x0] SCSISEQ1[0x12] SEQCTL0[0x0]
SEQINTCTL[0x0]
Aug  3 06:25:05 svil kernel: SEQ_FLAGS[0x0] SEQ_FLAGS2[0x4] QFREEZE_COUNT[0x0]
Aug  3 06:25:05 svil kernel: KERNEL_QFREEZE_COUNT[0x0] MK_MESSAGE_SCB[0xff00]
Aug  3 06:25:05 svil kernel: MK_MESSAGE_SCSIID[0xff] SSTAT0[0x2] SSTAT1[0x1]
Aug  3 06:25:05 svil kernel: SSTAT2[0x0] SSTAT3[0x0] PERRDIAG[0x0]
SIMODE1[0xac]
Aug  3 06:25:05 svil kernel: LQISTAT0[0x0] LQISTAT1[0x0] LQISTAT2[0x0]
LQOSTAT0[0x0]
Aug  3 06:25:05 svil kernel: LQOSTAT1[0x0] LQOSTAT2[0x0]
Aug  3 06:25:05 svil kernel:
Aug  3 06:25:05 svil kernel: SCB Count = 4 CMDS_PENDING = 1 LASTSCB 0xffff
CURRSCB 0x3 NEXTSCB 0x0
Aug  3 06:25:05 svil kernel: qinstart = 13 qinfifonext = 13
Aug  3 06:25:05 svil kernel: QINFIFO:
Aug  3 06:25:05 svil kernel: WAITING_TID_QUEUES:
Aug  3 06:25:05 svil kernel: Pending list:
Aug  3 06:25:05 svil kernel:   3 FIFO_USE[0x0] SCB_CONTROL[0x40]
SCB_SCSIID[0x37]
Aug  3 06:25:05 svil kernel: Total 1
Aug  3 06:25:05 svil kernel: Kernel Free SCB list: 2 1 0
Aug  3 06:25:05 svil kernel: Sequencer Complete DMA-inprog list:
Aug  3 06:25:05 svil kernel: Sequencer Complete list:
Aug  3 06:25:05 svil kernel: Sequencer DMA-Up and Complete list:
Aug  3 06:25:05 svil kernel: Sequencer On QFreeze and Complete list:
Aug  3 06:25:05 svil kernel:
Aug  3 06:25:05 svil kernel:
Aug  3 06:25:05 svil kernel: scsi5: FIFO0 Free, LONGJMP == 0x80ff, SCB 0x0
Aug  3 06:25:05 svil kernel: SEQIMODE[0x3f] SEQINTSRC[0x0] DFCNTRL[0x0]
DFSTATUS[0x89]
Aug  3 06:25:05 svil kernel: SG_CACHE_SHADOW[0x2] SG_STATE[0x0] DFFSXFRCTL[0x0]
Aug  3 06:25:05 svil kernel: SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR = 0x00, SHCNT =
0x0
Aug  3 06:25:05 svil kernel: HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]
Aug  3 06:25:05 svil kernel:
Aug  3 06:25:05 svil kernel: scsi5: FIFO1 Active, LONGJMP == 0x8063, SCB 0x3
Aug  3 06:25:05 svil kernel: SEQIMODE[0x3f] SEQINTSRC[0x0] DFCNTRL[0x4]
DFSTATUS[0x89]
Aug  3 06:25:05 svil kernel: SG_CACHE_SHADOW[0x2] SG_STATE[0x0] DFFSXFRCTL[0x0]
Aug  3 06:25:05 svil kernel: SOFFCNT[0x0] MDFFSTAT[0x14] SHADDR = 0x06, SHCNT =
0x0
Aug  3 06:25:05 svil kernel: HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]
Aug  3 06:25:05 svil kernel: LQIN: 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:05 svil kernel: scsi5: LQISTATE = 0x0, LQOSTATE = 0x0, OPTIONMODE
= 0x52
Aug  3 06:25:05 svil kernel: scsi5: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x0
Aug  3 06:25:05 svil kernel: scsi5: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
Aug  3 06:25:05 svil kernel: SIMODE0[0xc]
Aug  3 06:25:05 svil kernel: CCSCBCTL[0x4]
Aug  3 06:25:05 svil kernel: scsi5: REG0 == 0x3, SINDEX = 0x1e0, DINDEX = 0xe1
Aug  3 06:25:05 svil kernel: scsi5: SCBPTR == 0x3, SCB_NEXT == 0xffc0,
SCB_NEXT2 == 0xff65
Aug  3 06:25:05 svil kernel: CDB 12 0 0 0 24 0
Aug  3 06:25:05 svil kernel: STACK: 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:05 svil kernel: <<<<<<<<<<<<<<<<< Dump Card State Ends
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Aug  3 06:25:05 svil kernel: scsi 5:0:3:0: Device is active, asserting ATN
Aug  3 06:25:05 svil kernel: scsi5: Recovery code sleeping
Aug  3 06:25:05 svil kernel: scsi5: Timer Expired (active 1)
Aug  3 06:25:05 svil kernel: Recovery code awake
Aug  3 06:25:05 svil kernel: scsi5: Command abort returning 0x2003
Aug  3 06:25:06 svil kernel: scsi 5:0:3:0: Attempting to queue a TARGET RESET
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:06 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:06 svil kernel: scsi5: Device reset timer expired (active 2)
Aug  3 06:25:06 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:06 svil kernel: Recovery SCB completes
Aug  3 06:25:06 svil kernel: Recovery SCB completes
Aug  3 06:25:06 svil kernel: scsi 5:0:3:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi5: At time of recovery, card was not paused
Aug  3 06:25:06 svil kernel: >>>>>>>>>>>>>>>>>> Dump Card State Begins
<<<<<<<<<<<<<<<<<
Aug  3 06:25:06 svil kernel: scsi5: Dumping Card State at program address 0x34
Mode 0x22
Aug  3 06:25:06 svil kernel: Card was paused
Aug  3 06:25:06 svil kernel: INTSTAT[0x0] SELOID[0x3] SELID[0x0]
HS_MAILBOX[0x0]
Aug  3 06:25:06 svil kernel: INTCTL[0x80] SEQINTSTAT[0x0] SAVED_MODE[0x0]
DFFSTAT[0x33]
Aug  3 06:25:06 svil kernel: SCSISIGI[0x0] SCSIPHASE[0x0] SCSIBUS[0x0]
LASTPHASE[0x1]
Aug  3 06:25:06 svil kernel: SCSISEQ0[0x0] SCSISEQ1[0x12] SEQCTL0[0x0]
SEQINTCTL[0x0]
Aug  3 06:25:06 svil kernel: SEQ_FLAGS[0xc0] SEQ_FLAGS2[0x4] QFREEZE_COUNT[0x1]
Aug  3 06:25:06 svil kernel: KERNEL_QFREEZE_COUNT[0x1] MK_MESSAGE_SCB[0xff00]
Aug  3 06:25:06 svil kernel: MK_MESSAGE_SCSIID[0xff] SSTAT0[0x0] SSTAT1[0x8]
Aug  3 06:25:06 svil kernel: SSTAT2[0x0] SSTAT3[0x0] PERRDIAG[0x0]
SIMODE1[0xa4]
Aug  3 06:25:06 svil kernel: LQISTAT0[0x0] LQISTAT1[0x0] LQISTAT2[0x0]
LQOSTAT0[0x0]
Aug  3 06:25:06 svil kernel: LQOSTAT1[0x0] LQOSTAT2[0x0]
Aug  3 06:25:06 svil kernel:
Aug  3 06:25:06 svil kernel: SCB Count = 4 CMDS_PENDING = 0 LASTSCB 0xffff
CURRSCB 0x3 NEXTSCB 0x0
Aug  3 06:25:06 svil kernel: qinstart = 14 qinfifonext = 15
Aug  3 06:25:06 svil kernel: QINFIFO: 0x3
Aug  3 06:25:06 svil kernel: WAITING_TID_QUEUES:
Aug  3 06:25:06 svil kernel: Pending list:
Aug  3 06:25:06 svil kernel:   3 FIFO_USE[0x3] SCB_CONTROL[0x48]
SCB_SCSIID[0x37]
Aug  3 06:25:06 svil kernel: Total 1
Aug  3 06:25:06 svil kernel: Kernel Free SCB list: 2 1 0
Aug  3 06:25:06 svil kernel: Sequencer Complete DMA-inprog list:
Aug  3 06:25:06 svil kernel: Sequencer Complete list:
Aug  3 06:25:06 svil kernel: Sequencer DMA-Up and Complete list:
Aug  3 06:25:06 svil kernel: Sequencer On QFreeze and Complete list:
Aug  3 06:25:06 svil kernel:
Aug  3 06:25:06 svil kernel:
Aug  3 06:25:06 svil kernel: scsi5: FIFO0 Free, LONGJMP == 0x80ff, SCB 0x0
Aug  3 06:25:06 svil kernel: SEQIMODE[0x3f] SEQINTSRC[0x0] DFCNTRL[0x0]
DFSTATUS[0x89]
Aug  3 06:25:06 svil kernel: SG_CACHE_SHADOW[0x2] SG_STATE[0x0] DFFSXFRCTL[0x0]
Aug  3 06:25:06 svil kernel: SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR = 0x00, SHCNT =
0x0
Aug  3 06:25:06 svil kernel: HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]
Aug  3 06:25:06 svil kernel:
Aug  3 06:25:06 svil kernel: scsi5: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
Aug  3 06:25:06 svil kernel: SEQIMODE[0x3f] SEQINTSRC[0x0] DFCNTRL[0x4]
DFSTATUS[0x89]
Aug  3 06:25:06 svil kernel: SG_CACHE_SHADOW[0x2] SG_STATE[0x0] DFFSXFRCTL[0x0]
Aug  3 06:25:06 svil kernel: SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR = 0x00, SHCNT =
0x0
Aug  3 06:25:06 svil kernel: HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]
Aug  3 06:25:06 svil kernel: LQIN: 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi5: LQISTATE = 0x0, LQOSTATE = 0x0, OPTIONMODE
= 0x52
Aug  3 06:25:06 svil kernel: scsi5: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x0
Aug  3 06:25:06 svil kernel: scsi5: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
Aug  3 06:25:06 svil kernel: SIMODE0[0xc]
Aug  3 06:25:06 svil kernel: CCSCBCTL[0x0]
Aug  3 06:25:06 svil kernel: scsi5: REG0 == 0x3, SINDEX = 0x119, DINDEX = 0xe1
Aug  3 06:25:06 svil kernel: scsi5: SCBPTR == 0x3, SCB_NEXT == 0xff00,
SCB_NEXT2 == 0xffa4
Aug  3 06:25:06 svil kernel: CDB 0 0 0 0 0 0
Aug  3 06:25:06 svil kernel: STACK: 0x20 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:06 svil kernel: <<<<<<<<<<<<<<<<< Dump Card State Ends
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Aug  3 06:25:06 svil kernel: scsi5:0:3:0: Cmd aborted from QINFIFO
Aug  3 06:25:06 svil kernel: scsi 5:0:3:0: Device offlined - not ready after
error recovery
Aug  3 06:25:06 svil kernel: scsi 5:0:4:0: Attempting to queue an ABORT
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:4:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:4:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:4:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:4:0: Attempting to queue a TARGET RESET
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:06 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:06 svil kernel: scsi5: Device reset timer expired (active 1)
Aug  3 06:25:06 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:06 svil kernel: Recovery SCB completes
Aug  3 06:25:06 svil kernel: scsi 5:0:4:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:4:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:4:0: Device offlined - not ready after
error recovery
Aug  3 06:25:06 svil kernel: scsi 5:0:5:0: Attempting to queue an ABORT
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:5:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:5:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:5:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:5:0: Attempting to queue a TARGET RESET
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:06 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:06 svil kernel: scsi5: Device reset timer expired (active 1)
Aug  3 06:25:06 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:06 svil kernel: Recovery SCB completes
Aug  3 06:25:06 svil kernel: scsi 5:0:5:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:5:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:5:0: Device offlined - not ready after
error recovery
Aug  3 06:25:06 svil kernel: scsi 5:0:6:0: Attempting to queue an ABORT
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:6:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:6:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:6:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:6:0: Attempting to queue a TARGET RESET
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:06 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:06 svil kernel: scsi5: Device reset timer expired (active 1)
Aug  3 06:25:06 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:06 svil kernel: Recovery SCB completes
Aug  3 06:25:06 svil kernel: scsi 5:0:6:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:6:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:6:0: Device offlined - not ready after
error recovery
Aug  3 06:25:06 svil kernel: scsi 5:0:8:0: Attempting to queue an ABORT
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:8:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:8:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:8:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:8:0: Attempting to queue a TARGET RESET
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:06 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:06 svil kernel: scsi5: Device reset timer expired (active 1)
Aug  3 06:25:06 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:06 svil kernel: Recovery SCB completes
Aug  3 06:25:06 svil kernel: scsi 5:0:8:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:8:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:8:0: Device offlined - not ready after
error recovery
Aug  3 06:25:06 svil kernel: scsi 5:0:9:0: Attempting to queue an ABORT
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:9:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:9:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:9:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:9:0: Attempting to queue a TARGET RESET
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:06 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:06 svil kernel: scsi5: Device reset timer expired (active 1)
Aug  3 06:25:06 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:06 svil kernel: Recovery SCB completes
Aug  3 06:25:06 svil kernel: scsi 5:0:9:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:9:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:9:0: Device offlined - not ready after
error recovery
Aug  3 06:25:06 svil kernel: scsi 5:0:10:0: Attempting to queue an ABORT
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:10:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:10:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:10:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:10:0: Attempting to queue a TARGET RESET
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:06 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:06 svil kernel: scsi5: Device reset timer expired (active 1)
Aug  3 06:25:06 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:06 svil kernel: Recovery SCB completes
Aug  3 06:25:06 svil kernel: scsi 5:0:10:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:10:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:10:0: Device offlined - not ready after
error recovery
Aug  3 06:25:06 svil kernel: scsi 5:0:11:0: Attempting to queue an ABORT
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:11:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:11:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:11:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:11:0: Attempting to queue a TARGET RESET
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:06 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:06 svil kernel: scsi5: Device reset timer expired (active 1)
Aug  3 06:25:06 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:06 svil kernel: Recovery SCB completes
Aug  3 06:25:06 svil kernel: scsi 5:0:11:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:11:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:11:0: Device offlined - not ready after
error recovery
Aug  3 06:25:06 svil kernel: scsi 5:0:12:0: Attempting to queue an ABORT
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:12:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:12:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:12:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:12:0: Attempting to queue a TARGET RESET
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:06 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:06 svil kernel: scsi5: Device reset timer expired (active 1)
Aug  3 06:25:06 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:06 svil kernel: Recovery SCB completes
Aug  3 06:25:06 svil kernel: scsi 5:0:12:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:12:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:12:0: Device offlined - not ready after
error recovery
Aug  3 06:25:06 svil kernel: scsi 5:0:13:0: Attempting to queue an ABORT
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:13:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:13:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:13:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:13:0: Attempting to queue a TARGET RESET
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:06 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:06 svil kernel: scsi5: Device reset timer expired (active 1)
Aug  3 06:25:06 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:06 svil kernel: Recovery SCB completes
Aug  3 06:25:06 svil kernel: scsi 5:0:13:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:13:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:13:0: Device offlined - not ready after
error recovery
Aug  3 06:25:06 svil kernel: scsi 5:0:14:0: Attempting to queue an ABORT
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:14:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:14:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:06 svil kernel: scsi 5:0:14:0: Command already completed
Aug  3 06:25:06 svil kernel: scsi 5:0:14:0: Attempting to queue a TARGET RESET
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:06 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:07 svil kernel: scsi5: Device reset timer expired (active 1)
Aug  3 06:25:07 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:07 svil kernel: Recovery SCB completes
Aug  3 06:25:07 svil kernel: scsi 5:0:14:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:07 svil kernel: scsi 5:0:14:0: Command already completed
Aug  3 06:25:07 svil kernel: scsi 5:0:14:0: Device offlined - not ready after
error recovery
Aug  3 06:25:07 svil kernel: scsi 5:0:15:0: Attempting to queue an ABORT
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:07 svil kernel: scsi 5:0:15:0: Command already completed
Aug  3 06:25:07 svil kernel: scsi 5:0:15:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:07 svil kernel: scsi 5:0:15:0: Command already completed
Aug  3 06:25:07 svil kernel: scsi 5:0:15:0: Attempting to queue a TARGET RESET
message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Aug  3 06:25:07 svil kernel: scsi5: Device reset code sleeping
Aug  3 06:25:07 svil kernel: scsi5: Device reset timer expired (active 1)
Aug  3 06:25:07 svil kernel: scsi5: Device reset returning 0x2003
Aug  3 06:25:07 svil kernel: Recovery SCB completes
Aug  3 06:25:07 svil kernel: scsi 5:0:15:0: Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Aug  3 06:25:07 svil kernel: scsi 5:0:15:0: Command already completed
Aug  3 06:25:07 svil kernel: scsi 5:0:15:0: Device offlined - not ready after

error recovery

Signature · 3 lines
Configure bugmail: http://bugzilla.kernel.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are watching the assignee of the bug.
#2 lore raw
In reply to [email protected]
Quoted 64 lines · On Fri, 2009-09-11 at 09:18 +0000, [email protected] wrote:

http://bugzilla.kernel.org/show_bug.cgi?id=14159

           Summary: AIC79xx is not working properly with an attached scsi
                    tape since 2.6.29
           Product: SCSI Drivers
           Version: 2.5
    Kernel Version: 2.6.27 (working), 2.6.30 (not working)
          Platform: All
        OS/Version: Linux
              Tree: Mainline
            Status: NEW
          Severity: normal
          Priority: P1
         Component: Other
        AssignedTo: [email protected]
        ReportedBy: [email protected]
                CC: [email protected]
        Regression: Yes

Both kernels 2.6.27 and 2.6.28 are working correctly. Since Linux 2.6.29 till 2.6.31rc8 the regression(?) is out there.

Please let me know if I can provide any further details.

Best regards,
Gabriele

=================
Here is the messages part for Linux 2.6.27:

aic79xx 0000:41:01.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 scsi5 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
<Adaptec 29320ALP PCIx Ultra320 SCSI adapter>
aic7901: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs
target5:0:3: asynchronous
scsi 5:0:3:0: Sequential-Access IBM HH LTO Gen 2 0376 PQ: 0 ANSI: 3
target5:0:3: Beginning Domain Validation
target5:0:3: wide asynchronous
target5:0:3: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 126) target5:0:3: Ending Domain Validation
scsi 5:0:3:0: Attached scsi generic sg7 type 1
st: Version 20080504, fixed bufsize 32768, s/g segs 256
Driver 'st' needs updating - please use bus_type methods
st 5:0:3:0: Attached scsi tape st0
st 5:0:3:0: st0: try direct i/o: yes (alignment 4 B)
osst :I: Tape driver with OnStream support version 0.99.4
osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $ Driver 'osst' needs updating - please use bus_type methods
st0: Block limits 256 - 524288 bytes.
=================

=================
Here is Linux 2.6.30:

Aug  3 06:25:04 svil kernel: aic79xx 0000:41:01.0: PCI INT A -> GSI 19 (level,
low) -> IRQ 19
Aug  3 06:25:04 svil kernel: scsi5 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev
3.0
Aug  3 06:25:04 svil kernel:         <Adaptec 29320ALP PCIx Ultra320 SCSI
adapter>
Aug  3 06:25:04 svil kernel:         aic7901: Ultra320 Wide Channel A, SCSI
Id=7, PCI-X 101-1
Aug  3 06:25:04 svil kernel: scsi 5:0:0:0: Attempting to queue an ABORT
Quoted 1 line

message:CDB: 0x12 0x0

That's an inquiry to a non-existent target. It should have returned a DID_NO_CONNECT timeout within 250ms. The fact that it didn't is suggestive of interrupt routing problems. After all these messages have completed, what does /proc/interrupts say?

James

#3 lore raw

[Bug 14159] AIC79xx is not working properly with an attached scsi tape since 2.6.29

In reply to [email protected]

http://bugzilla.kernel.org/show_bug.cgi?id=14159

--- Comment #2 from Anonymous Emailer <[email protected]> 2009-09-11 23:27:53 ---
Reply-To: [email protected]

Quoted 64 lines · On Fri, 2009-09-11 at 09:18 +0000, [email protected] wrote:

http://bugzilla.kernel.org/show_bug.cgi?id=14159

           Summary: AIC79xx is not working properly with an attached scsi
                    tape since 2.6.29
           Product: SCSI Drivers
           Version: 2.5
    Kernel Version: 2.6.27 (working), 2.6.30 (not working)
          Platform: All
        OS/Version: Linux
              Tree: Mainline
            Status: NEW
          Severity: normal
          Priority: P1
         Component: Other
        AssignedTo: [email protected]
        ReportedBy: [email protected]
                CC: [email protected]
        Regression: Yes

Both kernels 2.6.27 and 2.6.28 are working correctly. Since Linux 2.6.29 till 2.6.31rc8 the regression(?) is out there.

Please let me know if I can provide any further details.

Best regards,
Gabriele

=================
Here is the messages part for Linux 2.6.27:

aic79xx 0000:41:01.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 scsi5 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
<Adaptec 29320ALP PCIx Ultra320 SCSI adapter>
aic7901: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs
target5:0:3: asynchronous
scsi 5:0:3:0: Sequential-Access IBM HH LTO Gen 2 0376 PQ: 0 ANSI: 3
target5:0:3: Beginning Domain Validation
target5:0:3: wide asynchronous
target5:0:3: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 126) target5:0:3: Ending Domain Validation
scsi 5:0:3:0: Attached scsi generic sg7 type 1
st: Version 20080504, fixed bufsize 32768, s/g segs 256
Driver 'st' needs updating - please use bus_type methods
st 5:0:3:0: Attached scsi tape st0
st 5:0:3:0: st0: try direct i/o: yes (alignment 4 B)
osst :I: Tape driver with OnStream support version 0.99.4
osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $ Driver 'osst' needs updating - please use bus_type methods
st0: Block limits 256 - 524288 bytes.
=================

=================
Here is Linux 2.6.30:

Aug  3 06:25:04 svil kernel: aic79xx 0000:41:01.0: PCI INT A -> GSI 19 (level,
low) -> IRQ 19
Aug  3 06:25:04 svil kernel: scsi5 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev
3.0
Aug  3 06:25:04 svil kernel:         <Adaptec 29320ALP PCIx Ultra320 SCSI
adapter>
Aug  3 06:25:04 svil kernel:         aic7901: Ultra320 Wide Channel A, SCSI
Id=7, PCI-X 101-1
Aug  3 06:25:04 svil kernel: scsi 5:0:0:0: Attempting to queue an ABORT
Quoted 1 line

message:CDB: 0x12 0x0

That's an inquiry to a non-existent target. It should have returned a DID_NO_CONNECT timeout within 250ms. The fact that it didn't is suggestive of interrupt routing problems. After all these messages have completed, what does /proc/interrupts say?

James

Signature · 3 lines
Configure bugmail: http://bugzilla.kernel.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are watching the assignee of the bug.
#4 lore raw

[Bug 14159] AIC79xx is not working properly with an attached scsi tape since 2.6.29

In reply to [email protected]

http://bugzilla.kernel.org/show_bug.cgi?id=14159

--- Comment #3 from [email protected] 2009-09-14 07:18:46 --- Hi James,

today after building and installing the latest stable kernel 2.6.31 I can tell you that the problem is still there.

Here is the machine's /proc/interrups

CPU0 CPU1

  0:         44          0   IO-APIC-edge      timer
  1:          0          2   IO-APIC-edge      i8042
  3:          0          0   IO-APIC-fasteoi   ehci_hcd:usb2, ohci_hcd:usb5,
ohci_hcd:usb6
  4:          0          2   IO-APIC-edge    
  8:          0          1   IO-APIC-edge      rtc0
  9:          0          0   IO-APIC-fasteoi   acpi, sata_svw
 12:          0          4   IO-APIC-edge      i8042
 14:         63      92631   IO-APIC-edge      ide0
 19:          0          0   IO-APIC-fasteoi   aic79xx
 20:        876    5417561   IO-APIC-fasteoi   eth0
 21:          0         29   IO-APIC-fasteoi   ehci_hcd:usb1, ohci_hcd:usb3,
ohci_hcd:usb4
 22:        268     827272   IO-APIC-fasteoi   aacraid
NMI:          0          0   Non-maskable interrupts
LOC:    3340059    3367236   Local timer interrupts
SPU:          0          0   Spurious interrupts
CNT:          0          0   Performance counter interrupts
PND:          0          0   Performance pending work
RES:     132590      57223   Rescheduling interrupts
CAL:         80         64   Function call interrupts
TLB:       8153       6593   TLB shootdowns
TRM:          0          0   Thermal event interrupts
THR:          0          0   Threshold APIC interrupts
MCE:          0          0   Machine check exceptions
MCP:         40         40   Machine check polls
ERR:          0
MIS:          0
Signature · 3 lines
Configure bugmail: http://bugzilla.kernel.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are watching the assignee of the bug.
#7 lore raw

[Bug 14159] AIC79xx is not working properly with an attached scsi tape since 2.6.29

In reply to [email protected]

http://bugzilla.kernel.org/show_bug.cgi?id=14159

--- Comment #4 from [email protected] 2009-09-14 07:19:51 --- Created an attachment (id=23092)
--> (http://bugzilla.kernel.org/attachment.cgi?id=23092)
2.6.31 dmesg output

This is the machine dmesg output with 2.6.31

Signature · 3 lines
Configure bugmail: http://bugzilla.kernel.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are watching the assignee of the bug.
#5 lore raw

Re: [Bug 14159] AIC79xx is not working properly with an attached scsi tape since 2.6.29

In reply to [email protected]
Quoted 7 lines

--- Comment #3 from [email protected] 2009-09-14 07:18:46 --- today after building and installing the latest stable kernel 2.6.31 I can tell you that the problem is still there.

Here is the machine's /proc/interrups

CPU0 CPU1

Quoted 10 lines
  0:         44          0   IO-APIC-edge      timer
  1:          0          2   IO-APIC-edge      i8042
  3:          0          0   IO-APIC-fasteoi   ehci_hcd:usb2, ohci_hcd:usb5,
ohci_hcd:usb6
  4:          0          2   IO-APIC-edge    
  8:          0          1   IO-APIC-edge      rtc0
  9:          0          0   IO-APIC-fasteoi   acpi, sata_svw
 12:          0          4   IO-APIC-edge      i8042
 14:         63      92631   IO-APIC-edge      ide0
 19:          0          0   IO-APIC-fasteoi   aic79xx

So this is the problem, as predicted: the card isn't getting interrupts. This would strongly suggest an ACPI problem. Can you try booting with pci=noacpi?

Thanks,

James

#8 lore raw

[Bug 14159] AIC79xx is not working properly with an attached scsi tape since 2.6.29

In reply to [email protected]

http://bugzilla.kernel.org/show_bug.cgi?id=14159

--- Comment #5 from Anonymous Emailer <[email protected]> 2009-09-14 14:25:23 ---
Reply-To: [email protected]

Quoted 7 lines

--- Comment #3 from [email protected] 2009-09-14 07:18:46 --- today after building and installing the latest stable kernel 2.6.31 I can tell you that the problem is still there.

Here is the machine's /proc/interrups

CPU0 CPU1

Quoted 10 lines
  0:         44          0   IO-APIC-edge      timer
  1:          0          2   IO-APIC-edge      i8042
  3:          0          0   IO-APIC-fasteoi   ehci_hcd:usb2, ohci_hcd:usb5,
ohci_hcd:usb6
  4:          0          2   IO-APIC-edge    
  8:          0          1   IO-APIC-edge      rtc0
  9:          0          0   IO-APIC-fasteoi   acpi, sata_svw
 12:          0          4   IO-APIC-edge      i8042
 14:         63      92631   IO-APIC-edge      ide0
 19:          0          0   IO-APIC-fasteoi   aic79xx

So this is the problem, as predicted: the card isn't getting interrupts. This would strongly suggest an ACPI problem. Can you try booting with pci=noacpi?

Thanks,

James

Signature · 3 lines
Configure bugmail: http://bugzilla.kernel.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are watching the assignee of the bug.
#6 lore raw

Re: [Bug 14159] AIC79xx is not working properly with an attached scsi tape since 2.6.29

In reply to James Bottomley
Quoted 18 lines · James Bottomley
Quoted 7 lines

--- Comment #3 from [email protected] 2009-09-14 07:18:46 --- today after building and installing the latest stable kernel 2.6.31 I can tell you that the problem is still there.

Here is the machine's /proc/interrups

CPU0 CPU1

Quoted 10 lines
  0:         44          0   IO-APIC-edge      timer
  1:          0          2   IO-APIC-edge      i8042
  3:          0          0   IO-APIC-fasteoi   ehci_hcd:usb2, ohci_hcd:usb5,
ohci_hcd:usb6
  4:          0          2   IO-APIC-edge    
  8:          0          1   IO-APIC-edge      rtc0
  9:          0          0   IO-APIC-fasteoi   acpi, sata_svw
 12:          0          4   IO-APIC-edge      i8042
 14:         63      92631   IO-APIC-edge      ide0
 19:          0          0   IO-APIC-fasteoi   aic79xx
Quoted 3 lines

So this is the problem, as predicted: the card isn't getting interrupts. This would strongly suggest an ACPI problem. Can you try booting with pci=noacpi?

You might also try "pci=noioapicquirk". Commit bbe194433bae [1] fiddles with boot interrupts on AMD 813x devices, which you seem to have.

Bjorn

[1] http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=bbe194433baeadc953f49e3795b41ffffc5486dd

#9 lore raw

[Bug 14159] AIC79xx is not working properly with an attached scsi tape since 2.6.29

In reply to [email protected]

http://bugzilla.kernel.org/show_bug.cgi?id=14159

--- Comment #6 from Bjorn Helgaas <[email protected]> 2009-09-14 17:24:42 ---

Quoted 18 lines · James Bottomley
Quoted 7 lines

--- Comment #3 from [email protected] 2009-09-14 07:18:46 --- today after building and installing the latest stable kernel 2.6.31 I can tell you that the problem is still there.

Here is the machine's /proc/interrups

CPU0 CPU1

Quoted 10 lines
  0:         44          0   IO-APIC-edge      timer
  1:          0          2   IO-APIC-edge      i8042
  3:          0          0   IO-APIC-fasteoi   ehci_hcd:usb2, ohci_hcd:usb5,
ohci_hcd:usb6
  4:          0          2   IO-APIC-edge    
  8:          0          1   IO-APIC-edge      rtc0
  9:          0          0   IO-APIC-fasteoi   acpi, sata_svw
 12:          0          4   IO-APIC-edge      i8042
 14:         63      92631   IO-APIC-edge      ide0
 19:          0          0   IO-APIC-fasteoi   aic79xx
Quoted 3 lines

So this is the problem, as predicted: the card isn't getting interrupts. This would strongly suggest an ACPI problem. Can you try booting with pci=noacpi?

You might also try "pci=noioapicquirk". Commit bbe194433bae [1] fiddles with boot interrupts on AMD 813x devices, which you seem to have.

Bjorn

[1]
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=bbe194433baeadc953f49e3795b41ffffc5486dd

Signature · 3 lines
Configure bugmail: http://bugzilla.kernel.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are watching the assignee of the bug.
#10 lore raw

[Bug 14159] AIC79xx is not working properly with an attached scsi tape since 2.6.29

In reply to [email protected]

http://bugzilla.kernel.org/show_bug.cgi?id=14159

--- Comment #7 from [email protected] 2009-09-15 07:05:46 --- Hi Bjorn and James,

pci=noacpi is not working, so even before reading Bjorn's reply, we tried "noapic" and the suddenly the tape device was working again. No more timeouts on initialization and so on.

I haven't tried pci=noioapicquirk yet, since the server is up for production and other people is working.
So I'm gonna do that later in the day.

Thank you very much for now.

Regards,
Gabriele

Signature · 3 lines
Configure bugmail: http://bugzilla.kernel.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are watching the assignee of the bug.
#12 lore raw

[Bug 14159] AIC79xx is not working properly with an attached scsi tape since 2.6.29

In reply to [email protected]

http://bugzilla.kernel.org/show_bug.cgi?id=14159

--- Comment #8 from [email protected] 2009-09-15 13:07:42 --- All right, we've just rebooted the server and tried with the "noioapicquirk" param and everything is fine.

Looking at the patch you put up in your reply I can see some code for amd_813x (quirk_disable_amd_813x_boot_interrupt and the definition for AMD_813X_REV_B2)

So just in case you need it, I'm pasting the lspci for the AMD-8131 we have. Please let me know if you need anything else.

Thank you,
Gabriele

40:0f.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-

    Latency: 150
    Bus: primary=40, secondary=41, subordinate=41, sec-latency=96
    I/O behind bridge: 00007000-00007fff
    Memory behind bridge: e1f00000-e1ffffff
    Prefetchable memory behind bridge: 00000000e0200000-00000000e02fffff
    Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-

<MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [a0] PCI-X bridge device
Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz
Status: Dev=40:0f.0 64bit+ 133MHz+ SCD- USC- SCO- SRD-
Upstream: Capacity=14 CommitmentLimit=65535
Downstream: Capacity=2 CommitmentLimit=65535
Capabilities: [b8] HyperTransport: Interrupt Discovery and Configuration
Capabilities: [c0] HyperTransport: Slave or Primary Interface
!!! Possibly incomplete decoding
Command: BaseUnitID=15 UnitCnt=2 MastHost- DefDir-
Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 Link Config 0: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 Link Config 1: MLWI=8bit MLWO=8bit LWI=N/C LWO=N/C Revision ID: 1.02

40:0f.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X IOAPIC (rev 01) (prog-if 10 [IO-APIC])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0

40:10.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-

    Latency: 150
    Bus: primary=40, secondary=42, subordinate=42, sec-latency=0
    I/O behind bridge: 0000f000-00000fff
    Memory behind bridge: fff00000-000fffff
    Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
    Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-

<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [a0] PCI-X bridge device
Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=conv
Status: Dev=40:10.0 64bit+ 133MHz+ SCD- USC- SCO- SRD-
Upstream: Capacity=14 CommitmentLimit=65535
Downstream: Capacity=2 CommitmentLimit=65535
Capabilities: [b8] HyperTransport: Interrupt Discovery and Configuration

40:10.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X IOAPIC (rev 01) (prog-if 10 [IO-APIC])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0

41:01.0 SCSI storage controller: Adaptec ASC-29320ALP U320 (rev 10)
Subsystem: Adaptec Unknown device 0044
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR-

    Latency: 148 (10000ns min, 6250ns max), Cache Line Size: 64 bytes
    Interrupt: pin A routed to IRQ 19
    Region 0: I/O ports at 7000 [disabled] [size=256]
    Region 1: Memory at e1f80000 (64-bit, non-prefetchable) [size=8K]
    Region 3: I/O ports at 7800 [disabled] [size=256]
    [virtual] Expansion ROM at e0200000 [disabled] [size=512K]
    Capabilities: [dc] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA

PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1
Enable-

        Address: 0000000000000000  Data: 0000
    Capabilities: [94] PCI-X non-bridge device
        Command: DPERE- ERO- RBC=512 OST=3
        Status: Dev=41:01.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=512

DMOST=8 DMCRS=16 RSCEM- 266MHz- 533MHz-

Signature · 3 lines
Configure bugmail: http://bugzilla.kernel.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are watching the assignee of the bug.
#11 lore raw

Re: [Bug 14159] AIC79xx is not working properly with an attached scsi tape since 2.6.29

In reply to [email protected]
Quoted 1 line · On Tue, 2009-09-15 at 07:05 +0000, [email protected] wrote:

http://bugzilla.kernel.org/show_bug.cgi?id=14159

cc'ing linux-acpi

James

Quoted 16 lines

--- Comment #7 from [email protected] 2009-09-15 07:05:46 --- Hi Bjorn and James,

pci=noacpi is not working, so even before reading Bjorn's reply, we tried "noapic" and the suddenly the tape device was working again. No more timeouts on initialization and so on.

I haven't tried pci=noioapicquirk yet, since the server is up for production and other people is working.
So I'm gonna do that later in the day.

Thank you very much for now.

Regards,
Gabriele

#15 lore raw

[Bug 14159] AIC79xx is not working properly with an attached scsi tape since 2.6.29

In reply to [email protected]

http://bugzilla.kernel.org/show_bug.cgi?id=14159

--- Comment #9 from Anonymous Emailer <[email protected]> 2009-09-15 13:53:40 ---
Reply-To: [email protected]

Quoted 1 line · On Tue, 2009-09-15 at 07:05 +0000, [email protected] wrote:

http://bugzilla.kernel.org/show_bug.cgi?id=14159

cc'ing linux-acpi

James

Quoted 16 lines

--- Comment #7 from [email protected] 2009-09-15 07:05:46 --- Hi Bjorn and James,

pci=noacpi is not working, so even before reading Bjorn's reply, we tried "noapic" and the suddenly the tape device was working again. No more timeouts on initialization and so on.

I haven't tried pci=noioapicquirk yet, since the server is up for production and other people is working.
So I'm gonna do that later in the day.

Thank you very much for now.

Regards,
Gabriele

Signature · 3 lines
Configure bugmail: http://bugzilla.kernel.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are watching the assignee of the bug.
#13 lore raw

Re: [Bug 14159] AIC79xx is not working properly with an attached scsi tape since 2.6.29

In reply to [email protected]
Quoted 1 line · On Tue, 2009-09-15 at 13:07 +0000, [email protected] wrote:

http://bugzilla.kernel.org/show_bug.cgi?id=14159

cc'ing linux-acpi

James

Quoted 105 lines

--- Comment #8 from [email protected] 2009-09-15 13:07:42 --- All right, we've just rebooted the server and tried with the "noioapicquirk" param and everything is fine.

Looking at the patch you put up in your reply I can see some code for amd_813x (quirk_disable_amd_813x_boot_interrupt and the definition for AMD_813X_REV_B2)

So just in case you need it, I'm pasting the lspci for the AMD-8131 we have. Please let me know if you need anything else.

Thank you,
Gabriele

40:0f.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-

    Latency: 150
    Bus: primary=40, secondary=41, subordinate=41, sec-latency=96
    I/O behind bridge: 00007000-00007fff
    Memory behind bridge: e1f00000-e1ffffff
    Prefetchable memory behind bridge: 00000000e0200000-00000000e02fffff
    Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-

<MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [a0] PCI-X bridge device
Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz
Status: Dev=40:0f.0 64bit+ 133MHz+ SCD- USC- SCO- SRD-
Upstream: Capacity=14 CommitmentLimit=65535
Downstream: Capacity=2 CommitmentLimit=65535
Capabilities: [b8] HyperTransport: Interrupt Discovery and Configuration
Capabilities: [c0] HyperTransport: Slave or Primary Interface
!!! Possibly incomplete decoding
Command: BaseUnitID=15 UnitCnt=2 MastHost- DefDir-
Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 Link Config 0: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 Link Config 1: MLWI=8bit MLWO=8bit LWI=N/C LWO=N/C Revision ID: 1.02

40:0f.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X IOAPIC (rev 01) (prog-if 10 [IO-APIC])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0

40:10.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-

    Latency: 150
    Bus: primary=40, secondary=42, subordinate=42, sec-latency=0
    I/O behind bridge: 0000f000-00000fff
    Memory behind bridge: fff00000-000fffff
    Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
    Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-

<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [a0] PCI-X bridge device
Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=conv
Status: Dev=40:10.0 64bit+ 133MHz+ SCD- USC- SCO- SRD-
Upstream: Capacity=14 CommitmentLimit=65535
Downstream: Capacity=2 CommitmentLimit=65535
Capabilities: [b8] HyperTransport: Interrupt Discovery and Configuration

40:10.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X IOAPIC (rev 01) (prog-if 10 [IO-APIC])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0

41:01.0 SCSI storage controller: Adaptec ASC-29320ALP U320 (rev 10)
Subsystem: Adaptec Unknown device 0044
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR-

    Latency: 148 (10000ns min, 6250ns max), Cache Line Size: 64 bytes
    Interrupt: pin A routed to IRQ 19
    Region 0: I/O ports at 7000 [disabled] [size=256]
    Region 1: Memory at e1f80000 (64-bit, non-prefetchable) [size=8K]
    Region 3: I/O ports at 7800 [disabled] [size=256]
    [virtual] Expansion ROM at e0200000 [disabled] [size=512K]
    Capabilities: [dc] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA

PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1
Enable-

        Address: 0000000000000000  Data: 0000
    Capabilities: [94] PCI-X non-bridge device
        Command: DPERE- ERO- RBC=512 OST=3
        Status: Dev=41:01.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=512

DMOST=8 DMCRS=16 RSCEM- 266MHz- 533MHz-

#16 lore raw

[Bug 14159] AIC79xx is not working properly with an attached scsi tape since 2.6.29

In reply to [email protected]

http://bugzilla.kernel.org/show_bug.cgi?id=14159

--- Comment #10 from Anonymous Emailer <[email protected]> 2009-09-15 13:55:57 ---
Reply-To: [email protected]

Quoted 1 line · On Tue, 2009-09-15 at 13:07 +0000, [email protected] wrote:

http://bugzilla.kernel.org/show_bug.cgi?id=14159

cc'ing linux-acpi

James

Quoted 105 lines

--- Comment #8 from [email protected] 2009-09-15 13:07:42 --- All right, we've just rebooted the server and tried with the "noioapicquirk" param and everything is fine.

Looking at the patch you put up in your reply I can see some code for amd_813x (quirk_disable_amd_813x_boot_interrupt and the definition for AMD_813X_REV_B2)

So just in case you need it, I'm pasting the lspci for the AMD-8131 we have. Please let me know if you need anything else.

Thank you,
Gabriele

40:0f.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-

    Latency: 150
    Bus: primary=40, secondary=41, subordinate=41, sec-latency=96
    I/O behind bridge: 00007000-00007fff
    Memory behind bridge: e1f00000-e1ffffff
    Prefetchable memory behind bridge: 00000000e0200000-00000000e02fffff
    Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-

<MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [a0] PCI-X bridge device
Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz
Status: Dev=40:0f.0 64bit+ 133MHz+ SCD- USC- SCO- SRD-
Upstream: Capacity=14 CommitmentLimit=65535
Downstream: Capacity=2 CommitmentLimit=65535
Capabilities: [b8] HyperTransport: Interrupt Discovery and Configuration
Capabilities: [c0] HyperTransport: Slave or Primary Interface
!!! Possibly incomplete decoding
Command: BaseUnitID=15 UnitCnt=2 MastHost- DefDir-
Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 Link Config 0: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 Link Config 1: MLWI=8bit MLWO=8bit LWI=N/C LWO=N/C Revision ID: 1.02

40:0f.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X IOAPIC (rev 01) (prog-if 10 [IO-APIC])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0

40:10.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-

    Latency: 150
    Bus: primary=40, secondary=42, subordinate=42, sec-latency=0
    I/O behind bridge: 0000f000-00000fff
    Memory behind bridge: fff00000-000fffff
    Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
    Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-

<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [a0] PCI-X bridge device
Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=conv
Status: Dev=40:10.0 64bit+ 133MHz+ SCD- USC- SCO- SRD-
Upstream: Capacity=14 CommitmentLimit=65535
Downstream: Capacity=2 CommitmentLimit=65535
Capabilities: [b8] HyperTransport: Interrupt Discovery and Configuration

40:10.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X IOAPIC (rev 01) (prog-if 10 [IO-APIC])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0

41:01.0 SCSI storage controller: Adaptec ASC-29320ALP U320 (rev 10)
Subsystem: Adaptec Unknown device 0044
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR-

    Latency: 148 (10000ns min, 6250ns max), Cache Line Size: 64 bytes
    Interrupt: pin A routed to IRQ 19
    Region 0: I/O ports at 7000 [disabled] [size=256]
    Region 1: Memory at e1f80000 (64-bit, non-prefetchable) [size=8K]
    Region 3: I/O ports at 7800 [disabled] [size=256]
    [virtual] Expansion ROM at e0200000 [disabled] [size=512K]
    Capabilities: [dc] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA

PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1
Enable-

        Address: 0000000000000000  Data: 0000
    Capabilities: [94] PCI-X non-bridge device
        Command: DPERE- ERO- RBC=512 OST=3
        Status: Dev=41:01.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=512

DMOST=8 DMCRS=16 RSCEM- 266MHz- 533MHz-

Signature · 3 lines
Configure bugmail: http://bugzilla.kernel.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are watching the assignee of the bug.
#14 lore raw

Re: [Bug 14159] AIC79xx is not working properly with an attached scsi tape since 2.6.29

In reply to James Bottomley
Quoted 4 lines
Quoted 4 lines

http://bugzilla.kernel.org/show_bug.cgi?id=14159
--- Comment #8 from [email protected] 2009-09-15 13:07:42 --- All right, we've just rebooted the server and tried with the "noioapicquirk" param and everything is fine.

Great, thanks. Gabriele, could you attach the "lspci -nn" output, please? I'm hoping Stefan will update the quirk, and I think he'll need the numeric device ID.

#17 lore raw

[Bug 14159] AIC79xx is not working properly with an attached scsi tape since 2.6.29

In reply to [email protected]

http://bugzilla.kernel.org/show_bug.cgi?id=14159

--- Comment #11 from Bjorn Helgaas <[email protected]> 2009-09-15 15:08:46 ---

Quoted 4 lines
Quoted 4 lines

http://bugzilla.kernel.org/show_bug.cgi?id=14159
--- Comment #8 from [email protected] 2009-09-15 13:07:42 --- All right, we've just rebooted the server and tried with the "noioapicquirk" param and everything is fine.

Great, thanks. Gabriele, could you attach the "lspci -nn" output, please? I'm hoping Stefan will update the quirk, and I think he'll need the numeric device ID.

Signature · 3 lines
Configure bugmail: http://bugzilla.kernel.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are watching the assignee of the bug.
#18 lore raw

[Bug 14159] AIC79xx is not working properly with an attached scsi tape since 2.6.29

In reply to [email protected]

http://bugzilla.kernel.org/show_bug.cgi?id=14159

--- Comment #12 from [email protected] 2009-09-15 15:14:58 --- Created an attachment (id=23097)
--> (http://bugzilla.kernel.org/attachment.cgi?id=23097)
lspci -nn output as requested (2.6.31)

Signature · 3 lines
Configure bugmail: http://bugzilla.kernel.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are watching the assignee of the bug.
#19 lore raw

[Bug 14159] AIC79xx is not working properly with an attached scsi tape since 2.6.29

In reply to [email protected]

http://bugzilla.kernel.org/show_bug.cgi?id=14159

--- Comment #13 from [email protected] 2009-09-15 15:20:57 --- Of course Bjorn.
There you go. You'll find the lspci -nn output in the attachments.

Thank you again.

Signature · 3 lines
Configure bugmail: http://bugzilla.kernel.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are watching the assignee of the bug.
#20 lore raw

[Bug 14159] AIC79xx is not working properly with an attached scsi tape since 2.6.29

In reply to [email protected]

http://bugzilla.kernel.org/show_bug.cgi?id=14159

--- Comment #14 from Stefan Assmann <[email protected]> 2009-09-16 09:16:35 --- Created an attachment (id=23100)
--> (http://bugzilla.kernel.org/attachment.cgi?id=23100)
skip disabling NOIOAMODE on AMD 8131 rev B1

Hi Gabriele,

could you please test again with the attached patch. I've added a check to skip rev B1 of the AMD 8131. While looking at the code I recognized that the DECLARE_PCI_FIXUP_* calls were missing some cases as well. So I fixed that too. Hope this works for you.

Signature · 3 lines
Configure bugmail: http://bugzilla.kernel.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are watching the assignee of the bug.
#21 lore raw

[Bug 14159] AIC79xx is not working properly with an attached scsi tape since 2.6.29

In reply to [email protected]

http://bugzilla.kernel.org/show_bug.cgi?id=14159

--- Comment #15 from [email protected] 2009-09-16 13:42:33 --- Hi Stefan,

I'm rebuilding the patched 2.6.31 kernel just right now. Tomorrow (unfortunately I'm not allowed to reboot today), I'll be able to reboot the server and let you know the outcome.

Signature · 3 lines
Configure bugmail: http://bugzilla.kernel.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are watching the assignee of the bug.
#22 lore raw

[Bug 14159] AIC79xx is not working properly with an attached scsi tape since 2.6.29

In reply to [email protected]

http://bugzilla.kernel.org/show_bug.cgi?id=14159

--- Comment #16 from [email protected] 2009-09-17 06:45:05 --- OK great, I tried with the patched kernel. It works.

Thanks

Signature · 3 lines
Configure bugmail: http://bugzilla.kernel.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are watching the assignee of the bug.
#23 lore raw

[Bug 14159] AIC79xx is not working properly with an attached scsi tape since 2.6.29

In reply to [email protected]

http://bugzilla.kernel.org/show_bug.cgi?id=14159

--- Comment #17 from Stefan Assmann <[email protected]> 2009-09-17 14:14:46 --- thanks for testing, I'll post the patch for upstream inclusion.

Signature · 3 lines
Configure bugmail: http://bugzilla.kernel.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are watching the assignee of the bug.