Skip to contentSkip to conversation

Highpoint 840A RocketRAID Controller and drives are NOT detected by SCSI_HPTIOP kernel module

Bug 198975 [email protected] 1 participant 3 messages Aug 6, 2022 – Sep 5, 2024 1 message not in the archive SCSI

lore
Share & tools
lore
#1 lore raw
In reply to a message not in the archive

https://bugzilla.kernel.org/show_bug.cgi?id=198975

Jaym12 ([email protected]) changed:

What |Removed |Added
----------------------------------------------------------------------------
CC| |[email protected]

--- Comment #7 from Jaym12 ([email protected]) --- I fixed this error(In reply to Matthias Lippert from comment #0)

Quoted 113 lines

Hello,

This is my first kernel bugzilla report, so please have mercy ;-)

My freshly bought Highpoint 840A RocketRAID Controller and its 8 connected "Samsung 860 EVO" ssd harddrives are NOT detected by the "SCSI_HPTIOP" kernel low-level scsi driver module, but it seems to be the smaller brother of the already from kernel supported 3740A RocketRAID controller by Highpoint.
The only differnence seems to be that the 840A supports only 6Gb/s per channel.
Thats is also confirmed by the top down view onto the expansion card. In the upper right corner you can see the described dual product markings "RocketRAID 3740A/840A", so the layout and most likely also the raid processor of the controller has been used at least twice by Highpoint. My controllers firmware is the recent 1.0.0 version.
I couldnt find any other driver module that is matching my controller more closely.
The current published linux drivers by highpoint are useless under (Gentoo) Linux.
The controller and its connected drives are working flawlessy under Windows 10, so its not damaged. I am using a "Gigabyte X99-SLI" motherboard with recent F24a bios version.
I am also willingly able to provide regular dump logs to kernel developers for driver debugging.

I would be VERY thankful for including support into the next kernel for this cool piece of hardware!

Top-down view onto the expansion card:

https://www.bhphotovideo.com/images/images1000x1000/
highpoint_rocketraid_3740a_12gb_s_pcie_1269779.jpg

dmesg outputs only this, then nothing else related to my controller:

RocketRAID 3xxx/4xxx Controller driver v1.10.0

lspci -kvv outputs this:

02:00.0 RAID bus controller: HighPoint Technologies, Inc. Device 0840 (rev a1)
Subsystem: HighPoint Technologies, Inc. Device 0000 Physical Slot: 6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
NUMA node: 0
Region 0: Memory at d0900000 (64-bit, prefetchable) [size=1M] Region 4: Memory at d0a00000 (64-bit, prefetchable) [size=256K] Expansion ROM at dfe00000 [disabled] [size=128K]
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0+,D1+,D2-,D3hot+,D3cold-)

                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [90] MSI: Enable- Count=1/32 Maskable+ 64bit+
                Address: 0000000000000000  Data: 0000
                Masking: 00000000  Pending: 00000000
        Capabilities: [b0] MSI-X: Enable- Count=18 Masked-
                Vector table: BAR=0 offset=00038000
                PBA: BAR=0 offset=00039000
        Capabilities: [c0] Express (v2) Endpoint, MSI 00
                DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s

<128ns, L1 <2us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
SlotPowerLimit 0.000W
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 256 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr-
TransPend-
LnkCap: Port #0, Speed 8GT/s, Width x8, ASPM L0s L1, Exit
Latency L0s <128ns, L1 <2us
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 8GT/s, Width x8, TrErr- Train- SlotClk-
DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range B, TimeoutDis+, LTR-,
OBFF Not Supported
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-,
LTR-, OBFF Disabled
LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB,
EqualizationComplete+, EqualizationPhase1+
EqualizationPhase2+, EqualizationPhase3+,
LinkEqualizationRequest-
Capabilities: [100 v2] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+
ChkEn-

        Capabilities: [300 v1] #19
Quoted 7 lines

Highpoints 800er series RocketRAID website:

http://www.highpoint-tech.com/USA_new/series-rr800-overview.htm

Highpoints 3700er series RocketRAID website:

http://www.highpoint-tech.com/USA_new/series-rr3700-overview.htm

Quoted 2 lines

I have been facing the same issue.
https://www.allhdd.com/seagate-st3000lm024-sata-6gbps-hdd/

Signature · 4 lines
You may reply to this email to add a comment.

You are receiving this mail because:
You are watching the assignee of the bug.
#2 lore raw
In reply to a message not in the archive

https://bugzilla.kernel.org/show_bug.cgi?id=198975

Carol Jams ([email protected]) changed:

What |Removed |Added
----------------------------------------------------------------------------
CC| |[email protected]

--- Comment #8 from Carol Jams ([email protected]) --- (In reply to Jaym12 from comment #7)

Quoted 116 lines

I fixed this error(In reply to Matthias Lippert from comment #0)

Quoted 26 lines

Hello,

This is my first kernel bugzilla report, so please have mercy ;-)

My freshly bought Highpoint 840A RocketRAID Controller and its 8 connected "Samsung 860 EVO" ssd harddrives are NOT detected by the "SCSI_HPTIOP" kernel low-level scsi driver module, but it seems to be the smaller brother of the already from kernel supported 3740A RocketRAID controller by Highpoint.
The only differnence seems to be that the 840A supports only 6Gb/s per channel.
Thats is also confirmed by the top down view onto the expansion card. In the upper right corner you can see the described dual product markings "RocketRAID 3740A/840A", so the layout and most likely also the raid processor of the controller has been used at least twice by Highpoint. My controllers firmware is the recent 1.0.0 version.
I couldnt find any other driver module that is matching my controller more closely.
The current published linux drivers by highpoint are useless under (Gentoo) Linux.
The controller and its connected drives are working flawlessy under Windows 10, so its not damaged. I am using a "Gigabyte X99-SLI" motherboard with recent F24a bios version.
I am also willingly able to provide regular dump logs to kernel developers for driver debugging.

Quoted 1 line

I would be VERY thankful for including support into the next kernel for

this

Quoted 55 lines

cool piece of hardware!

Top-down view onto the expansion card:

https://www.bhphotovideo.com/images/images1000x1000/
highpoint_rocketraid_3740a_12gb_s_pcie_1269779.jpg

dmesg outputs only this, then nothing else related to my controller:

RocketRAID 3xxx/4xxx Controller driver v1.10.0

lspci -kvv outputs this:

02:00.0 RAID bus controller: HighPoint Technologies, Inc. Device 0840 (rev a1)
Subsystem: HighPoint Technologies, Inc. Device 0000 Physical Slot: 6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
NUMA node: 0
Region 0: Memory at d0900000 (64-bit, prefetchable) [size=1M] Region 4: Memory at d0a00000 (64-bit, prefetchable) [size=256K] Expansion ROM at dfe00000 [disabled] [size=128K]
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0+,D1+,D2-,D3hot+,D3cold-)

                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [90] MSI: Enable- Count=1/32 Maskable+ 64bit+
                Address: 0000000000000000  Data: 0000
                Masking: 00000000  Pending: 00000000
        Capabilities: [b0] MSI-X: Enable- Count=18 Masked-
                Vector table: BAR=0 offset=00038000
                PBA: BAR=0 offset=00039000
        Capabilities: [c0] Express (v2) Endpoint, MSI 00
                DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s

<128ns, L1 <2us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
SlotPowerLimit 0.000W
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 256 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr-
TransPend-
LnkCap: Port #0, Speed 8GT/s, Width x8, ASPM L0s L1, Exit
Latency L0s <128ns, L1 <2us
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-

Quoted 8 lines

ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 8GT/s, Width x8, TrErr- Train- SlotClk-
DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range B, TimeoutDis+, LTR-,
OBFF Not Supported
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-,
LTR-, OBFF Disabled
LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance-

SpeedDis-

Quoted 23 lines

Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB,
EqualizationComplete+, EqualizationPhase1+
EqualizationPhase2+, EqualizationPhase3+,
LinkEqualizationRequest-
Capabilities: [100 v2] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+
ChkEn-

        Capabilities: [300 v1] #19
Quoted 11 lines
Quoted 7 lines

Highpoints 800er series RocketRAID website:

http://www.highpoint-tech.com/USA_new/series-rr800-overview.htm

Highpoints 3700er series RocketRAID website:

http://www.highpoint-tech.com/USA_new/series-rr3700-overview.htm

Quoted 2 lines

I have been facing the same issue.
https://www.allhdd.com/seagate-st3000lm024-sata-6gbps-hdd/

You can use https://www.allhdd.com/samsung-mz-77q4t0-sata-ssd/ drive it is working fine for me.

Signature · 4 lines
You may reply to this email to add a comment.

You are receiving this mail because:
You are watching the assignee of the bug.
#3 lore raw
In reply to a message not in the archive

https://bugzilla.kernel.org/show_bug.cgi?id=198975

Jack Hicks ([email protected]) changed:

What |Removed |Added
----------------------------------------------------------------------------
CC| |[email protected]

--- Comment #9 from Jack Hicks ([email protected]) --- Hello,

This is my first Bugzilla report, so I appreciate your patience!

I recently purchased a Highpoint 840A RocketRAID Controller with eight connected Samsung 860 EVO SSDs . Unfortunately, the "SCSI_HPTIOP" kernel low-level SCSI driver module does not detect this controller. It appears that the 840A is a smaller version of the 3740A, which is already supported by the kernel. The main difference seems to be that the 840A supports only 6Gb/s per channel, as indicated by the product markings on the card.

I am currently using the latest firmware version 1.0.0 for the controller. I couldn't find any other driver modules that might be compatible with my controller. The drivers available from Highpoint for Linux do not work on (Gentoo) Linux. The controller and SSDs
(https://serverorbit.com/solid-state-drives-ssd/sata-6gbps-ssd) are functioning perfectly under Windows 10, so the hardware is not faulty. I am using a Gigabyte X99-SLI motherboard with BIOS version F24a.

I am willing to provide regular dump logs for driver debugging if needed. I would be extremely grateful if support for this hardware could be included in the next kernel release!

Here is a top-down view of the expansion card for reference:
[Top-down view of the expansion card](https://www.bhphotovideo.com/images/images1000x1000/highpoint_rocketraid_3740a_12gb_s_pcie_1269779.jpg)

Current dmesg output:

```
RocketRAID 3xxx/4xxx Controller driver v1.10.0
```

lspci -kvv output:

```
02:00.0 RAID bus controller: HighPoint Technologies, Inc. Device 0840 (rev a1)
        Subsystem: HighPoint Technologies, Inc. Device 0000
        Physical Slot: 6
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 11
        NUMA node: 0
        Region 0: Memory at d0900000 (64-bit, prefetchable) [size=1M]
        Region 4: Memory at d0a00000 (64-bit, prefetchable) [size=256K]
        Expansion ROM at dfe00000 [disabled] [size=128K]
        Capabilities: [80] Power Management version 3
                Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0+,D1+,D2-,D3hot+,D3cold-)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [90] MSI: Enable- Count=1/32 Maskable+ 64bit+
                Address: 0000000000000000  Data: 0000
                Masking: 00000000  Pending: 00000000
        Capabilities: [b0] MSI-X: Enable- Count=18 Masked-
                Vector table: BAR=0 offset=00038000
                PBA: BAR=0 offset=00039000
        Capabilities: [c0] Express (v2) Endpoint, MSI 00
                DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <128ns,
L1 <2us
                        ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
SlotPowerLimit 0.000W
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
                        MaxPayload 256 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr-
TransPend-
                LnkCap: Port #0, Speed 8GT/s, Width x8, ASPM L0s L1, Exit
Latency L0s <128ns, L1 <2us
                        ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp+
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 8GT/s, Width x8, TrErr- Train- SlotClk- DLActive-
BWMgmt- ABWMgmt-
                DevCap2: Completion Timeout: Range B, TimeoutDis+, LTR-, OBFF
Not Supported
                DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-,
OBFF Disabled
                LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-
                         Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
                         Compliance De-emphasis: -6dB
                LnkSta2: Current De-emphasis Level: -6dB,
EqualizationComplete+, EqualizationPhase1+
                         EqualizationPhase2+, EqualizationPhase3+,
LinkEqualizationRequest-
        Capabilities: [100 v2] Advanced Error Reporting
                UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
                CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
                CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
                AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
        Capabilities: [300 v1] #19
```

For more information on the Highpoint 800 series RocketRAID:
[Highpoint 800 Series Overview](http://www.highpoint-tech.com/USA_new/series-rr800-overview.htm)

And the 3700 series RocketRAID:
[Highpoint 3700 Series Overview](http://www.highpoint-tech.com/USA_new/series-rr3700-overview.htm)

Thank you for your help!

Signature · 4 lines
You may reply to this email to add a comment.

You are receiving this mail because:
You are watching the assignee of the bug.