New: LSI SAS1068 logical volume caching mode not detected (with patch)
https://bugzilla.kernel.org/show_bug.cgi?id=216964
Bug ID: 216964
Summary: LSI SAS1068 logical volume caching mode not detected
(with patch)
Product: SCSI Drivers
Version: 2.5
Kernel Version: 5.15.58
Hardware: All
OS: Linux
Tree: Mainline
Status: NEW
Severity: normal
Priority: P1
Component: Other
Assignee: [email protected]
Reporter: [email protected]
Regression: NoCreated attachment 303641
--> https://bugzilla.kernel.org/attachment.cgi?id=303641&action=edit
Patch to use fixed size buffer for the buggy MODE SENSE command
Hardware:
HBA card: Broadcom / LSI SAS1068 PCI-X Fusion-MPT SAS
PCI VID:PID: 1000:0054
Problem: Caching mode of logical volumes managed by the controller in question is not detected.
Relevant kernel messages:
[ 19.642388] scsi 8:1:0:0: Direct-Access LSILOGIC Logical Volume 3000 PQ: 0 ANSI: 2 [ 19.649179] sd 8:1:0:0: Attached scsi generic sg6 type 0 [ 19.649390] sd 8:1:0:0: [sdd] 583983104 512-byte logical blocks: (299 GB/278 GiB) [ 19.649625] sd 8:1:0:0: [sdd] Write Protect is off [ 19.649629] sd 8:1:0:0: [sdd] Mode Sense: 03 00 00 08 [ 19.649837] sd 8:1:0:0: [sdd] No Caching mode page found [ 19.649853] sd 8:1:0:0: [sdd] Assuming drive cache: write through [ 19.666881] sdd: sdd1 sdd2 sdd3 [ 19.667776] sd 8:1:0:0: [sdd] Attached SCSI disk
Cause of the problem:
The SCSI MODE SENSE command is broken for the logical volumes managed by the controller in question in that it does not set the length field in the returned response to the length of the entire response but rather only to the length of the portion of the response actually written to the provided buffer (which is obviously limited by the length of the provided buffer). This breaks the logic in sd_read_cache_type [1] which first tries to determine the size of the entire response by executing the MODE SENSE command with a small buffer and then uses the length field from the partial response to size the buffer for the entire response appropriately. This does not work for the logical volumes managed by the controller in question as for them the reported response length is never greater than the length of the provided buffer (in fact it is always 3 as evidenced by the first byte in the "Mode Sense:" log message - which is the length of the small buffer provided to the MODE SENSE command less the length byte itself), so the response is never received in its entirety, which leads to the caching mode detection failure.
The problem can be demonstrated by the sg_modes command:
- invoked on the misbehaving logical volume:
# sg_modes -6 -p 8 -m 4 -d -H /dev/sdd
LSILOGIC Logical Volume 3000 peripheral_type: disk [0x0]
00 03 00 00 00
- invoked on a correctly behaving disk:
# sg_modes -6 -p 8 -m 4 -d -H /dev/sda
ATA WDC WD4003FFBX-6 0A83 peripheral_type: disk [0x0]
00 17 00 00 00
Notice the difference in the length field - the first byte of the response.Nevertheless the misbehaving logical volume _does_ report the caching mode correctly when the relevant MODE SENSE command is executed with large enough buffer. Again this can be demonstrated by the sg_modes command:
# sg_modes -6 -p 8 -m 192 -d -H /dev/sdd
LSILOGIC Logical Volume 3000 peripheral_type: disk [0x0]
00 17 00 00 00 08 12 04 00 ff ff 00 00 ff 00 ff ff
10 00 0f 00 00 00 00 00 00Possible fix:
It turns out there is already a flag in struct scsi_device which forces the relevant MODE SENSE command to be executed with a 192 bytes long buffer (which is long enough to hold the entire response): use_192_bytes_for_3f [2]. When this flag is set for the misbehaving disk/logical volume (together with the skip_ms_page_8 flag), the caching mode detection works correctly. This has been verified by applying the attached patch.
With the patch applied, the relevant kernel messages look like this:
[ 19.263001] scsi 8:1:0:0: Direct-Access LSILOGIC Logical Volume 3000 PQ: 0 ANSI: 2 [ 19.263190] sd 8:1:0:0: Attached scsi generic sg6 type 0 [ 19.263413] sd 8:1:0:0: [sdd] 583983104 512-byte logical blocks: (299 GB/278 GiB) [ 19.263690] sd 8:1:0:0: [sdd] Write Protect is off [ 19.263694] sd 8:1:0:0: [sdd] Mode Sense: 67 00 00 08 [ 19.263970] sd 8:1:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 19.279922] sdd: sdd1 sdd2 sdd3 [ 19.280904] sd 8:1:0:0: [sdd] Attached SCSI disk
https://elixir.bootlin.com/linux/v5.15.58/source/drivers/scsi/sd.c#L2687
https://elixir.bootlin.com/linux/v5.15.58/source/include/scsi/scsi_device.h#L184
Signature · 4 lines
You may reply to this email to add a comment. You are receiving this mail because: You are watching the assignee of the bug.