Skip to contentSkip to conversation

New: RTL9210: "unmap" in provisioning_mode keeps getting overwritten to "full"

Bug 220810 [email protected] 1 participant 1 message Nov 26, 2025 SCSI

lore
Share & tools
lore
#0 lore raw

https://bugzilla.kernel.org/show_bug.cgi?id=220810

Bug ID: 220810
Summary: RTL9210: "unmap" in provisioning_mode keeps getting
overwritten to "full"
Product: IO/Storage
Version: 2.5
Hardware: All
OS: Linux
Status: NEW
Severity: normal
Priority: P3
Component: SCSI
Assignee: [email protected]
Reporter: [email protected]
Regression: No

I have a Ugreen NVMe M.2 to USB enclosure. lsusb reports it as (long version follows later):
Bus 001 Device 012: ID 0bda:9210 Realtek Semiconductor Corp. RTL9210 M.2 NVME Adapter

The device supports unmap/TRIM/discard but doesn't seem to report this to the OS correctly. sg_vpd -a on the device reports: LBPU=1. This suggests trim should work. But the system sets the provisioning_mode to "full":

# cat
/sys/devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.0/host8/target8:0:0/8:0:0:0/scsi_disk/8:0:0:0/provisioning_mode
full

And therefore when I try to run blkdiscard on the device I get: Operation not supported.

Windows is able to trim the device, which seems to support that the device is capable of trim, but possibly Windows doesn't care about the chip's inaccurate report.

When I manually write "unmap" to provisioning_mode, I can successfully run blkdiscard. So I created the following udev rule:
ACTION=="add|change", ATTRS{idVendor}=="0bda", ATTRS{idProduct}=="9210", SUBSYSTEM=="scsi_disk", ATTR{provisioning_mode}="unmap"

After a reboot the device indeed has "unmap" set and trim works:

# cat
/sys/devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.0/host8/target8:0:0/8:0:0:0/scsi_disk/8:0:0:0/provisioning_mode
unmap

So far, so good, but this is where the real problem starts: After a short time it always gets set back to "full" automatically. Unfortunately I see no related messages in dmesg when this happens. The change might sometimes be triggered by my actions, such as opening a LUKS volume, but it also seems to happen by itself even when I don't do anything with the device. I tried disabling and masking the udisks2 service to make sure it doesn't interfere, but that didn't help. I also tried watching the provisioning_mode file with inotify to see what changes it but didn't get any messages when it changed.

Please let me know if I can provide any more information.

Steps to reproduce:
* Create udev rule
* Plug in device -> provisioning_mode initially set by udev to "unmap"
* blkdiscard works
* Perform action on device, or wait
* provisioning_mode reverts to "full"
* blkdiscard now fails with "Operation not supported"

=====

Additional info:

Kernel is current Debian Trixie stock kernel, no patches

# uname -a
Linux homura 6.12.57+deb13-amd64 #1 SMP PREEMPT_DYNAMIC Debian 6.12.57-1
(2025-11-05) x86_64 GNU/Linux

-----

# cat /proc/version
Linux version 6.12.57+deb13-amd64 ([email protected])
(x86_64-linux-gnu-gcc-14 (Debian 14.2.0-19) 14.2.0, GNU ld (GNU Binutils for
Debian) 2.44) #1 SMP PREEMPT_DYNAMIC Debian 6.12.57-1 (2025-11-05)

-----

# sg_vpd -a /dev/sde
Supported VPD pages VPD page:
  Supported VPD pages [sv]
  Unit serial number [sn]
  Device identification [di]
  Block limits (SBC) [bl]
  Block device characteristics (SBC) [bdc]
  Logical block provisioning (SBC) [lbpv]

Unit serial number VPD page:
Product serial number: 0000000000000000

Device Identification VPD page:
Addressed logical unit:
designator type: T10 vendor identification, code set: ASCII
vendor id: Realtek
vendor specific: RTL9210 1.000000000000000000
designator type: NAA, code set: Binary
0x3001237923792379

Block limits VPD page (SBC)
Write same non-zero (WSNZ): 0
Maximum compare and write length: 0 blocks [command not implemented] Optimal transfer length granularity: 0x1
Maximum transfer length: 0xffff
Optimal transfer length: 0xffff
Maximum prefetch length: 0 blocks [not reported]
Maximum unmap LBA count: 0x1400000
Maximum unmap block descriptor count: 0x1
Optimal unmap granularity: 0x1
Unmap granularity alignment valid: false
Maximum write same length: 0 blocks [not reported]
Maximum atomic transfer length: 0 blocks [not reported]
Atomic alignment: 0 blocks [unaligned atomic writes permitted] Atomic transfer length granularity: 0 blocks [no granularity requirement] Maximum atomic transfer length with atomic boundary: 0 blocks [not reported] Maximum atomic boundary size: 0 blocks [can only write atomic 1 block]

Block device characteristics VPD page (SBC)
Non-rotating medium (e.g. solid state)
Product type: Not specified
WABEREQ=0
WACEREQ=0
Nominal form factor: not reported
MACT=0
ZONED=0 [not reported]
RBWZ=0
FUAB=0
VBULS=0
DEPOPULATION TIME: 0x0

Logical block provisioning VPD page (SBC)
LBPU=1
LBPWS=0
LBPWS10=0
LBPRZ=0x0
ANC_SUP=0
DP=0
Minimum percentage: 0 [not reported] Provisioning type: not known or fully provisioned Threshold percentage: 0 [percentages not supported]

-----

# lsusb -vvv -d 0bda:9210

Bus 001 Device 012: ID 0bda:9210 Realtek Semiconductor Corp. RTL9210 M.2 NVME Adapter
Negotiated speed: High Speed (480Mbps)
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.10

  bDeviceClass            0 [unknown]
  bDeviceSubClass         0 [unknown]
  bDeviceProtocol         0 
  bMaxPacketSize0        64
  idVendor           0x0bda Realtek Semiconductor Corp.
  idProduct          0x9210 RTL9210 M.2 NVME Adapter
  bcdDevice           f0.01
  iManufacturer           1 Ugreen
  iProduct                2 Ugreen Storage Device
  iSerial                 3 01293805A6A5
  bNumConfigurations      1

Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0020
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk-Only
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Binary Object Store Descriptor:
bLength 5
bDescriptorType 15
wTotalLength 0x002a
bNumDeviceCaps 3
USB 2.0 Extension Device Capability:
bLength 7
bDescriptorType 16
bDevCapabilityType 2
bmAttributes 0x00000006
BESL Link Power Management (LPM) Supported
SuperSpeed USB Device Capability:
bLength 10
bDescriptorType 16
bDevCapabilityType 3
bmAttributes 0x00
wSpeedsSupported 0x000e
Device can operate at Full Speed (12Mbps)
Device can operate at High Speed (480Mbps)
Device can operate at SuperSpeed (5Gbps)
bFunctionalitySupport 1
Lowest fully-functional device speed is Full Speed (12Mbps)
bU1DevExitLat 10 micro seconds
bU2DevExitLat 2047 micro seconds
SuperSpeedPlus USB Device Capability:

    bLength                20
    bDescriptorType        16
    bDevCapabilityType     10

bmAttributes 0x00000001
Sublink Speed Attribute count 2
Sublink Speed ID count 1
wFunctionalitySupport 0x1100
Min functional Speed Attribute ID: 0
Min functional RX lanes: 1
Min functional TX lanes: 1
bmSublinkSpeedAttr[0] 0x000a4030
Speed Attribute ID: 0 10Gb/s Symmetric RX SuperSpeedPlus
bmSublinkSpeedAttr[1] 0x000a40b0
Speed Attribute ID: 0 10Gb/s Symmetric TX SuperSpeedPlus
can't get debug descriptor: Resource temporarily unavailable
Device Status: 0x0000
(Bus Powered)

-----

dmesg at boot when the device is initialized:

[  176.009742] usb 1-3: new high-speed USB device number 12 using xhci_hcd
[  176.155752] usb 1-3: New USB device found, idVendor=0bda, idProduct=9210,
bcdDevice=f0.01
[  176.155765] usb 1-3: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[  176.155770] usb 1-3: Product: Ugreen Storage Device
[  176.155774] usb 1-3: Manufacturer: Ugreen
[  176.155778] usb 1-3: SerialNumber: 01293805A6A5
[  176.214591] usb-storage 1-3:1.0: USB Mass Storage device detected
[  176.214909] scsi host8: usb-storage 1-3:1.0
[  176.214959] usbcore: registered new interface driver usb-storage
[  176.220056] usbcore: registered new interface driver uas
[  179.875749] scsi 8:0:0:0: Direct-Access     WD_BLACK  SN850X 2000GB   1.00
PQ: 0 ANSI: 6
[  179.876489] sd 8:0:0:0: Attached scsi generic sg4 type 0
[  179.881878] sd 8:0:0:0: [sde] 3907029168 512-byte logical blocks: (2.00
TB/1.82 TiB)
[  179.882510] sd 8:0:0:0: [sde] Write Protect is off
[  179.882515] sd 8:0:0:0: [sde] Mode Sense: 37 00 00 08
[  179.883171] sd 8:0:0:0: [sde] Write cache: disabled, read cache: enabled,
doesn't support DPO or FUA
[  179.959742] sd 8:0:0:0: [sde] Attached SCSI disk
Signature · 4 lines
You may reply to this email to add a comment.

You are receiving this mail because:
You are the assignee for the bug.