New: no disks are found at driver start after upgrate from 2.6.35.8 to 2.6.36
https://bugzilla.kernel.org/show_bug.cgi?id=22512
Summary: no disks are found at driver start after upgrate from
2.6.35.8 to 2.6.36
Product: SCSI Drivers
Version: 2.5
Kernel Version: 2.6.36
Platform: All
OS/Version: Linux
Tree: Mainline
Status: NEW
Severity: blocking
Priority: P1
Component: QLOGIC QLA2XXX
AssignedTo: [email protected]
ReportedBy: [email protected]
Regression: Yes
Driver loads without errors but after messages:
[ 993.976622] qla2xxx 0000:0c:00.0: LIP reset occurred (f700). [ 993.996537] qla2xxx 0000:0c:00.0: LIP occurred (f700). [ 993.996690] qla2xxx 0000:0c:00.0: LIP reset occurred (f7f7). [ 995.027739] qla2xxx 0000:0c:00.0: LOOP UP detected (4 Gbps). [ 995.620024] qla2xxx 0000:0c:00.0: [ 995.620026] QLogic Fibre Channel HBA Driver: 8.03.04-k0 [ 995.620027] QLogic QLE2460 - PCI-Express Single Channel 4Gb Fibre Channel HBA [ 995.620028] ISP2432: PCIe (2.5GT/s x4) @ 0000:0c:00.0 hdma+, host#=14,
fw=5.03.07 (496)
No disks are detected
Previous kernel detects:
[ 4.017172] scsi 1:0:0:0: Direct-Access IBM 1814 FAStT 0916 PQ: 0 ANSI: 5 [ 4.017576] sd 1:0:0:0: Attached scsi generic sg3 type 0 [ 4.017702] sd 1:0:0:0: Embedded Enclosure Device [ 4.018413] sd 1:0:0:0: [sdb] 838860800 512-byte logical blocks: (429 GB/400 GiB) [ 4.019311] sd 1:0:0:0: [sdb] Write Protect is off [ 4.019444] sd 1:0:0:0: [sdb] Mode Sense: 77 00 10 08 [ 4.019842] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled,
supports DPO and FUA
and many others
driver is compiled as module
Signature · 3 lines
Configure bugmail: https://bugzilla.kernel.org/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are watching the assignee of the bug.
[email protected]
Applied[Bug 22512] no disks are found at driver start after upgrate from 2.6.35.8 to 2.6.36
https://bugzilla.kernel.org/show_bug.cgi?id=22512
Andrew Vasquez <[email protected]> changed:
What |Removed |Added
----------------------------------------------------------------------------
CC| |[email protected]
--- Comment #1 from Andrew Vasquez <[email protected]> 2010-11-09 21:15:44 --- Could you test with the following patch:
Applied to 2.6.36? The patch above is already in 2.6.37-rc1.
Signature · 3 lines
Configure bugmail: https://bugzilla.kernel.org/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are watching the assignee of the bug.
[Bug 22512] no disks are found at driver start after upgrate from 2.6.35.8 to 2.6.36
In reply to [email protected]https://bugzilla.kernel.org/show_bug.cgi?id=22512
--- Comment #2 from [email protected] 2010-11-10 18:07:42 --- This patch seems to be already applied to 2.6.36. Here you are part of qla24xx_logio_entry
if (iop[0] & BIT_4) {
fcport->port_type = FCT_TARGET;
if (iop[0] & BIT_8)
fcport->flags |= FCF_FCP2_DEVICE;
} else if (iop[0] & BIT_5)
fcport->port_type = FCT_INITIATOR;
if (logio->io_parameter[7] || logio->io_parameter[8])Signature · 3 lines
Configure bugmail: https://bugzilla.kernel.org/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are watching the assignee of the bug.
[Bug 22512] no disks are found at driver start after upgrate from 2.6.35.8 to 2.6.36
In reply to [email protected]https://bugzilla.kernel.org/show_bug.cgi?id=22512
--- Comment #3 from Andrew Vasquez <[email protected]> 2010-11-10 18:18:09 --- Apologize, that was the wrong link. Try this one:
[SCSI] qla2xxx: Add module parameter to enable/disable GFF_ID device type
check.
Add the module parameter ql2xgffidenable to disable/enable the use of the GFF_ID name server command to prevent non FCP SCSI devices from being added
to
the driver's internal fc_port database.
Signature · 3 lines
Configure bugmail: https://bugzilla.kernel.org/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are watching the assignee of the bug.
[Bug 22512] no disks are found at driver start after upgrate from 2.6.35.8 to 2.6.36
In reply to [email protected]https://bugzilla.kernel.org/show_bug.cgi?id=22512
--- Comment #4 from [email protected] 2010-11-10 19:56:47 --- (In reply to comment #3)
Quoted 5 lines
Apologize, that was the wrong link. Try this one:
[SCSI] qla2xxx: Add module parameter to enable/disable
GFF_IDdevice type
check.
Quoted 7 lines
Add the module parameter ql2xgffidenable to disable/enable the use of the
GFF_IDname server command to prevent non FCP SCSI devices from being added
to
the driver's internalfc_portdatabase.
This is it.
May be somebody should build 2.6.36.1
Signature · 3 lines
Configure bugmail: https://bugzilla.kernel.org/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are watching the assignee of the bug.
[Bug 22512] no disks are found at driver start after upgrate from 2.6.35.8 to 2.6.36
In reply to [email protected]https://bugzilla.kernel.org/show_bug.cgi?id=22512
[email protected] changed:
What |Removed |Added
----------------------------------------------------------------------------
Status|NEW |RESOLVED
Resolution| |CODE_FIX--- Comment #5 from [email protected] 2010-12-22 16:19:43 --- Fixed in 2.6.36.2
Signature · 3 lines
Configure bugmail: https://bugzilla.kernel.org/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are watching the assignee of the bug.