New: Kernel OOPSes when suspend/resume

Bugme-new Andrew Morton 4 participants 13 messages Jun 26, 2007 1 message not in the archive

Subsystems (2)

Networking Network drivers

lore

Share & tools

lore

A message that is not in the archive (sent off-list or not yet received): [email protected]/

Andrew Morton

author

2007-06-26 17:09 UTC #1 lore raw

Quoted 157 lines · On Tue, 26 Jun 2007 08:22:11 -0700 (PDT) [email protected] wrote:

http://bugzilla.kernel.org/show_bug.cgi?id=8678
Summary: Kernel OOPSes when suspend/resume
Product: Power Management
Version: 2.5
KernelVersion: 2.6.21.5
Platform: All
OS/Version: Linux
Tree: Mainline
Status: NEW
Severity: high
Priority: P1
Component: Hibernation/Suspend
AssignedTo: [email protected]
ReportedBy: [email protected]
Most recent kernel where this bug did not occur:
Distribution: Debian Etch
Hardware Environment: Laptop Prestigio (Pentium M) Software Environment: 2.6.21.5, v4l-dvb-b03a5545f8e1 Problem Description:
--------------
Stopping tasks ... done.
Shrinking memory... done (0 pages freed)
Freed 0 kbytes in 0.02 seconds (0.00 MB/s)
Suspending console(s)
dvb_usb_dib0700 4-1:1.0: no suspend for driver dvb_usb_dib0700?
eth2: Going into suspend...
ACPI: PCI interrupt for device 0000:02:0c.0 disabled
radeonfb (0000:01:00.0): suspending for event: 1...
ACPI: PCI interrupt for device 0000:00:1f.6 disabled
ACPI: PCI interrupt for device 0000:00:1f.5 disabled
ACPI: PCI interrupt for device 0000:00:1d.7 disabled
ACPI: PCI interrupt for device 0000:00:1d.2 disabled
ACPI: PCI interrupt for device 0000:00:1d.1 disabled
ACPI: PCI interrupt for device 0000:00:1d.0 disabled
swsusp: critical section:
swsusp: Need to copy 112337 pages
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.0 to 64
usb usb1: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.1 to 64
usb usb2: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.2 to 64
usb usb3: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.7 to 64
usb usb4: root hub lost power or was reset
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PM: Writing back config space on device 0000:00:1f.5 at offset 1 (was 2900007, writing 2900003)
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1f.5 to 64
PM: Writing back config space on device 0000:00:1f.6 at offset 1 (was 2900005, writing 2900001)
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1f.6 to 64
radeonfb (0000:01:00.0): resuming from state: 1...
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[ffdff800-ffdfffff] Max Packet=[2048] IR/IT contexts=[4/8]
eth0: link down
Yenta O2: res at 0x94/0xD4: 00/ea
Yenta O2: enabling read prefetch/write burst
eth2: Coming out of suspend...
ACPI: PCI Interrupt 0000:02:0c.0[A] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
pnp: Failed to activate device 00:03.
pnp: Failed to activate device 00:04.
usbdev4.12_ep00: PM: resume from 0, parent 4-1 still 1
dvb_usb_dib0700 4-1:1.0: PM: resume from 1, parent 4-1 still 1 i2c_adapter i2c-5: PM: resume from 0, parent 4-1 still 1
usbdev4.12_ep01: PM: resume from 0, parent 4-1:1.0 still 1 usbdev4.12_ep81: PM: resume from 0, parent 4-1:1.0 still 1 usbdev4.12_ep82: PM: resume from 0, parent 4-1:1.0 still 1 usbdev4.12_ep83: PM: resume from 0, parent 4-1:1.0 still 1 usbdev4.12: PM: resume from 0, parent 4-1 still 1
usbdev1.8_ep00: PM: resume from 0, parent 1-2 still 1
hci_usb 1-2:1.0: PM: resume from 1, parent 1-2 still 1
hci0: PM: resume from 0, parent 1-2:1.0 still 1
usbdev1.8_ep81: PM: resume from 0, parent 1-2:1.0 still 1 usbdev1.8_ep02: PM: resume from 0, parent 1-2:1.0 still 1 usbdev1.8_ep82: PM: resume from 0, parent 1-2:1.0 still 1
hci_usb 1-2:1.1: PM: resume from 1, parent 1-2 still 1
usbdev1.8_ep03: PM: resume from 0, parent 1-2:1.1 still 1 usbdev1.8_ep83: PM: resume from 0, parent 1-2:1.1 still 1 usbdev1.8: PM: resume from 0, parent 1-2 still 1
Restarting tasks ... done.
__tx_submit: hci0 tx submit failed urb f22ca854 type 1 err -19
usb 1-2: USB disconnect, address 8
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[drm] Loading R300 Microcode
BUG: unable to handle kernel NULL pointer dereference at virtual address
00000000
printing eip:
c014787a
*pde = 00000000
Oops: 0000 [#1]
PREEMPT
Modules linked in: michael_mic arc4 ecb blkcipher ieee80211_crypt_tkip
xt_TCPMSS xt_tcpmss xt_tcpudp iptable_mangle ip_tables x_table
s ppp_deflate zlib_deflate bsd_comp ppp_async crc_ccitt ppp_generic slhc mt2060 dvb_usb_dib0700 dib7000m dib7000p dvb_usb dvb_core di
b3000mc dibx000_common bnep rfcomm hidp hid l2cap capability commoncap eeprom sr_mod sbp2 scsi_mod 8250_pci 8250 serial_core eth1394
hci_usb bluetooth snd_intel8x0m snd_intel8x0 snd_ac97_codec snd_seq_oss ac97_bus snd_seq_midi_event snd_seq snd_seq_device snd_pcm_os
s snd_mixer_oss ipw2200 8139too ieee80211 ieee80211_crypt snd_pcm snd_timer iTCO_wdt ehci_hcd mii ohci1394 ieee1394 rtc uhci_hcd snd snd_page_alloc ide_cd i2c_i801 pcspkr cdrom
CPU:    0
EIP:    0060:[<c014787a>]    Not tainted VLI
EFLAGS: 00010203   (2.6.21 #4)
EIP is at put_page+0x5/0xb2
eax: 00000000 ebx: 00000000 ecx: c0317380 edx: f63f70c0
esi: ea6e2680 edi: f784dd84 ebp: f784de48 esp: f784dd4c
ds: 007b es: 007b fs: 00d8 gs: 0033 ss: 0068
Process syslogd (pid: 3160, ti=f784c000 task=f7995070 task.ti=f784c000)
Stack: 00000001 ea6e2680 f784dd84 c02aebed ea6e2680 f784df20 c02aea21 ea6e26b0
       c02f58fb 00000036 000001ff f7ca36c0 f7dcfb00 ea6e2680 00000d1f 00000000
       00000000 00000000 00000001 00000000 000001ff 0ac3ac80 00000036 c0317380
Call Trace:
 [<c02aebed>] skb_release_data+0x4e/0x80
 [<c02aea21>] kfree_skbmem+0x8/0x61
 [<c02f58fb>] unix_dgram_recvmsg+0x214/0x239
 [<c02a9e24>] sock_recvmsg+0xec/0x107
 [<c0128b23>] autoremove_wake_function+0x0/0x35
 [<c0166775>] core_sys_select+0x1aa/0x2bc
 [<c0160a26>] pipe_write+0x356/0x3ed
 [<c015ae4d>] do_sync_readv_writev+0xc1/0xfe
 [<c02aad15>] sys_recvfrom+0xd7/0x12b
 [<c0128b23>] autoremove_wake_function+0x0/0x35
 [<c02aada0>] sys_recv+0x37/0x3b
 [<c02ab283>] sys_socketcall+0x19c/0x261
 [<c0120dc5>] sigprocmask+0x94/0xb1
 [<c0103cdc>] syscall_call+0x7/0xb
 =======================
Code: 42 c0 e8 66 fe ff ff 89 e0 25 00 e0 ff ff ff 48 14 8b 40 08 a8 08 74 05
e9 18 0f 1b 00 c3 e8 b4 ff ff ff 31 c0 c3 57 56 53 89 c                        
                                               3 <8b> 00 f6 c4 40 74 0a 89 d8

Quoted 2 lines

5b 5e 5f e9 e9 fb ff ff ff 4b 04 0f
EIP: [<c014787a>] put_page+0x5/0xb2 SS:ESP 0068:f784dd4c

Good heavens.

Does it oops every time? And does the oops trace always look like this?

Quoted 32 lines

usb 4-1: USB disconnect, address 12
dvb-usb: Leadtek Winfast DTV Dongle (STK7700P based) successfully deinitialized and disconnected.
usb 4-1: new high speed USB device using ehci_hcd and address 14 usb 4-1: configuration #1 chosen from 1 choice
dvb-usb: found a 'Leadtek Winfast DTV Dongle (STK7700P based)' in cold state, will try to load a firmware
dvb-usb: downloading firmware from file 'dvb-usb-dib0700-01.fw'
dib0700: firmware started successfully.
dvb-usb: found a 'Leadtek Winfast DTV Dongle (STK7700P based)' in warm state. i2c_adapter i2c-5: SMBus Quick command not supported, can't probe for chips
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (Leadtek Winfast DTV Dongle (STK7700P based)) i2c_adapter i2c-6: SMBus Quick command not supported, can't probe for chips
DVB: registering frontend 0 (DiBcom 7000MA/MB/PA/PB/MC)...
MT2060: successfully identified (IF1 = 1220)
dvb-usb: Leadtek Winfast DTV Dongle (STK7700P based) successfully initialized and connected.
usb 1-2: new full speed USB device using uhci_hcd and address 9 usb 1-2: configuration #1 chosen from 1 choice
----------------
Steps to reproduce:
suspend/resume
Signature · 3 lines
Configure bugmail: http://bugzilla.kernel.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are on the CC list for the bug, or are watching someone who is.

Andrew Morton

author

2007-06-26 17:10 UTC #2 lore raw

In reply to a message not in the archive

Quoted 157 lines · On Tue, 26 Jun 2007 08:22:11 -0700 (PDT) [email protected] wrote:

http://bugzilla.kernel.org/show_bug.cgi?id=8678
Summary: Kernel OOPSes when suspend/resume
Product: Power Management
Version: 2.5
KernelVersion: 2.6.21.5
Platform: All
OS/Version: Linux
Tree: Mainline
Status: NEW
Severity: high
Priority: P1
Component: Hibernation/Suspend
AssignedTo: [email protected]
ReportedBy: [email protected]
Most recent kernel where this bug did not occur:
Distribution: Debian Etch
Hardware Environment: Laptop Prestigio (Pentium M) Software Environment: 2.6.21.5, v4l-dvb-b03a5545f8e1 Problem Description:
--------------
Stopping tasks ... done.
Shrinking memory... done (0 pages freed)
Freed 0 kbytes in 0.02 seconds (0.00 MB/s)
Suspending console(s)
dvb_usb_dib0700 4-1:1.0: no suspend for driver dvb_usb_dib0700?
eth2: Going into suspend...
ACPI: PCI interrupt for device 0000:02:0c.0 disabled
radeonfb (0000:01:00.0): suspending for event: 1...
ACPI: PCI interrupt for device 0000:00:1f.6 disabled
ACPI: PCI interrupt for device 0000:00:1f.5 disabled
ACPI: PCI interrupt for device 0000:00:1d.7 disabled
ACPI: PCI interrupt for device 0000:00:1d.2 disabled
ACPI: PCI interrupt for device 0000:00:1d.1 disabled
ACPI: PCI interrupt for device 0000:00:1d.0 disabled
swsusp: critical section:
swsusp: Need to copy 112337 pages
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.0 to 64
usb usb1: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.1 to 64
usb usb2: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.2 to 64
usb usb3: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.7 to 64
usb usb4: root hub lost power or was reset
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PM: Writing back config space on device 0000:00:1f.5 at offset 1 (was 2900007, writing 2900003)
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1f.5 to 64
PM: Writing back config space on device 0000:00:1f.6 at offset 1 (was 2900005, writing 2900001)
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1f.6 to 64
radeonfb (0000:01:00.0): resuming from state: 1...
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[ffdff800-ffdfffff] Max Packet=[2048] IR/IT contexts=[4/8]
eth0: link down
Yenta O2: res at 0x94/0xD4: 00/ea
Yenta O2: enabling read prefetch/write burst
eth2: Coming out of suspend...
ACPI: PCI Interrupt 0000:02:0c.0[A] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
pnp: Failed to activate device 00:03.
pnp: Failed to activate device 00:04.
usbdev4.12_ep00: PM: resume from 0, parent 4-1 still 1
dvb_usb_dib0700 4-1:1.0: PM: resume from 1, parent 4-1 still 1 i2c_adapter i2c-5: PM: resume from 0, parent 4-1 still 1
usbdev4.12_ep01: PM: resume from 0, parent 4-1:1.0 still 1 usbdev4.12_ep81: PM: resume from 0, parent 4-1:1.0 still 1 usbdev4.12_ep82: PM: resume from 0, parent 4-1:1.0 still 1 usbdev4.12_ep83: PM: resume from 0, parent 4-1:1.0 still 1 usbdev4.12: PM: resume from 0, parent 4-1 still 1
usbdev1.8_ep00: PM: resume from 0, parent 1-2 still 1
hci_usb 1-2:1.0: PM: resume from 1, parent 1-2 still 1
hci0: PM: resume from 0, parent 1-2:1.0 still 1
usbdev1.8_ep81: PM: resume from 0, parent 1-2:1.0 still 1 usbdev1.8_ep02: PM: resume from 0, parent 1-2:1.0 still 1 usbdev1.8_ep82: PM: resume from 0, parent 1-2:1.0 still 1
hci_usb 1-2:1.1: PM: resume from 1, parent 1-2 still 1
usbdev1.8_ep03: PM: resume from 0, parent 1-2:1.1 still 1 usbdev1.8_ep83: PM: resume from 0, parent 1-2:1.1 still 1 usbdev1.8: PM: resume from 0, parent 1-2 still 1
Restarting tasks ... done.
__tx_submit: hci0 tx submit failed urb f22ca854 type 1 err -19
usb 1-2: USB disconnect, address 8
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[drm] Loading R300 Microcode
BUG: unable to handle kernel NULL pointer dereference at virtual address
00000000
printing eip:
c014787a
*pde = 00000000
Oops: 0000 [#1]
PREEMPT
Modules linked in: michael_mic arc4 ecb blkcipher ieee80211_crypt_tkip
xt_TCPMSS xt_tcpmss xt_tcpudp iptable_mangle ip_tables x_table
s ppp_deflate zlib_deflate bsd_comp ppp_async crc_ccitt ppp_generic slhc mt2060 dvb_usb_dib0700 dib7000m dib7000p dvb_usb dvb_core di
b3000mc dibx000_common bnep rfcomm hidp hid l2cap capability commoncap eeprom sr_mod sbp2 scsi_mod 8250_pci 8250 serial_core eth1394
hci_usb bluetooth snd_intel8x0m snd_intel8x0 snd_ac97_codec snd_seq_oss ac97_bus snd_seq_midi_event snd_seq snd_seq_device snd_pcm_os
s snd_mixer_oss ipw2200 8139too ieee80211 ieee80211_crypt snd_pcm snd_timer iTCO_wdt ehci_hcd mii ohci1394 ieee1394 rtc uhci_hcd snd snd_page_alloc ide_cd i2c_i801 pcspkr cdrom
CPU:    0
EIP:    0060:[<c014787a>]    Not tainted VLI
EFLAGS: 00010203   (2.6.21 #4)
EIP is at put_page+0x5/0xb2
eax: 00000000 ebx: 00000000 ecx: c0317380 edx: f63f70c0
esi: ea6e2680 edi: f784dd84 ebp: f784de48 esp: f784dd4c
ds: 007b es: 007b fs: 00d8 gs: 0033 ss: 0068
Process syslogd (pid: 3160, ti=f784c000 task=f7995070 task.ti=f784c000)
Stack: 00000001 ea6e2680 f784dd84 c02aebed ea6e2680 f784df20 c02aea21 ea6e26b0
       c02f58fb 00000036 000001ff f7ca36c0 f7dcfb00 ea6e2680 00000d1f 00000000
       00000000 00000000 00000001 00000000 000001ff 0ac3ac80 00000036 c0317380
Call Trace:
 [<c02aebed>] skb_release_data+0x4e/0x80
 [<c02aea21>] kfree_skbmem+0x8/0x61
 [<c02f58fb>] unix_dgram_recvmsg+0x214/0x239
 [<c02a9e24>] sock_recvmsg+0xec/0x107
 [<c0128b23>] autoremove_wake_function+0x0/0x35
 [<c0166775>] core_sys_select+0x1aa/0x2bc
 [<c0160a26>] pipe_write+0x356/0x3ed
 [<c015ae4d>] do_sync_readv_writev+0xc1/0xfe
 [<c02aad15>] sys_recvfrom+0xd7/0x12b
 [<c0128b23>] autoremove_wake_function+0x0/0x35
 [<c02aada0>] sys_recv+0x37/0x3b
 [<c02ab283>] sys_socketcall+0x19c/0x261
 [<c0120dc5>] sigprocmask+0x94/0xb1
 [<c0103cdc>] syscall_call+0x7/0xb
 =======================
Code: 42 c0 e8 66 fe ff ff 89 e0 25 00 e0 ff ff ff 48 14 8b 40 08 a8 08 74 05
e9 18 0f 1b 00 c3 e8 b4 ff ff ff 31 c0 c3 57 56 53 89 c                        
                                               3 <8b> 00 f6 c4 40 74 0a 89 d8

Quoted 2 lines

5b 5e 5f e9 e9 fb ff ff ff 4b 04 0f
EIP: [<c014787a>] put_page+0x5/0xb2 SS:ESP 0068:f784dd4c

Good heavens.

Does it oops every time? And does the oops trace always look like this?

Quoted 32 lines

usb 4-1: USB disconnect, address 12
dvb-usb: Leadtek Winfast DTV Dongle (STK7700P based) successfully deinitialized and disconnected.
usb 4-1: new high speed USB device using ehci_hcd and address 14 usb 4-1: configuration #1 chosen from 1 choice
dvb-usb: found a 'Leadtek Winfast DTV Dongle (STK7700P based)' in cold state, will try to load a firmware
dvb-usb: downloading firmware from file 'dvb-usb-dib0700-01.fw'
dib0700: firmware started successfully.
dvb-usb: found a 'Leadtek Winfast DTV Dongle (STK7700P based)' in warm state. i2c_adapter i2c-5: SMBus Quick command not supported, can't probe for chips
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (Leadtek Winfast DTV Dongle (STK7700P based)) i2c_adapter i2c-6: SMBus Quick command not supported, can't probe for chips
DVB: registering frontend 0 (DiBcom 7000MA/MB/PA/PB/MC)...
MT2060: successfully identified (IF1 = 1220)
dvb-usb: Leadtek Winfast DTV Dongle (STK7700P based) successfully initialized and connected.
usb 1-2: new full speed USB device using uhci_hcd and address 9 usb 1-2: configuration #1 chosen from 1 choice
----------------
Steps to reproduce:
suspend/resume
Signature · 3 lines
Configure bugmail: http://bugzilla.kernel.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are on the CC list for the bug, or are watching someone who is.

CIJOML

2007-06-26 17:42 UTC #3 lore raw

Dne úterý 26 červen 2007 19:09 Andrew Morton napsal(a):

Quoted 1 line

On Tue, 26 Jun 2007 08:22:11 -0700 (PDT) [email protected]

Quoted 160 lines · wrote:

Quoted 157 lines
http://bugzilla.kernel.org/show_bug.cgi?id=8678
Summary: Kernel OOPSes when suspend/resume
Product: Power Management
Version: 2.5
KernelVersion: 2.6.21.5
Platform: All
OS/Version: Linux
Tree: Mainline
Status: NEW
Severity: high
Priority: P1
Component: Hibernation/Suspend
AssignedTo: [email protected]
ReportedBy: [email protected]
Most recent kernel where this bug did not occur:
Distribution: Debian Etch
Hardware Environment: Laptop Prestigio (Pentium M) Software Environment: 2.6.21.5, v4l-dvb-b03a5545f8e1 Problem Description:
--------------
Stopping tasks ... done.
Shrinking memory... done (0 pages freed)
Freed 0 kbytes in 0.02 seconds (0.00 MB/s)
Suspending console(s)
dvb_usb_dib0700 4-1:1.0: no suspend for driver dvb_usb_dib0700?
eth2: Going into suspend...
ACPI: PCI interrupt for device 0000:02:0c.0 disabled
radeonfb (0000:01:00.0): suspending for event: 1...
ACPI: PCI interrupt for device 0000:00:1f.6 disabled
ACPI: PCI interrupt for device 0000:00:1f.5 disabled
ACPI: PCI interrupt for device 0000:00:1d.7 disabled
ACPI: PCI interrupt for device 0000:00:1d.2 disabled
ACPI: PCI interrupt for device 0000:00:1d.1 disabled
ACPI: PCI interrupt for device 0000:00:1d.0 disabled
swsusp: critical section:
swsusp: Need to copy 112337 pages
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.0 to 64
usb usb1: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.1 to 64
usb usb2: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.2 to 64
usb usb3: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.7 to 64
usb usb4: root hub lost power or was reset
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PM: Writing back config space on device 0000:00:1f.5 at offset 1 (was 2900007, writing 2900003)
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1f.5 to 64
PM: Writing back config space on device 0000:00:1f.6 at offset 1 (was 2900005, writing 2900001)
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1f.6 to 64 radeonfb (0000:01:00.0): resuming from state: 1...
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[ffdff800-ffdfffff] Max Packet=[2048] IR/IT contexts=[4/8]
eth0: link down
Yenta O2: res at 0x94/0xD4: 00/ea
Yenta O2: enabling read prefetch/write burst
eth2: Coming out of suspend...
ACPI: PCI Interrupt 0000:02:0c.0[A] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
pnp: Failed to activate device 00:03.
pnp: Failed to activate device 00:04.
usbdev4.12_ep00: PM: resume from 0, parent 4-1 still 1
dvb_usb_dib0700 4-1:1.0: PM: resume from 1, parent 4-1 still 1 i2c_adapter i2c-5: PM: resume from 0, parent 4-1 still 1
usbdev4.12_ep01: PM: resume from 0, parent 4-1:1.0 still 1 usbdev4.12_ep81: PM: resume from 0, parent 4-1:1.0 still 1 usbdev4.12_ep82: PM: resume from 0, parent 4-1:1.0 still 1 usbdev4.12_ep83: PM: resume from 0, parent 4-1:1.0 still 1 usbdev4.12: PM: resume from 0, parent 4-1 still 1 usbdev1.8_ep00: PM: resume from 0, parent 1-2 still 1
hci_usb 1-2:1.0: PM: resume from 1, parent 1-2 still 1
hci0: PM: resume from 0, parent 1-2:1.0 still 1 usbdev1.8_ep81: PM: resume from 0, parent 1-2:1.0 still 1 usbdev1.8_ep02: PM: resume from 0, parent 1-2:1.0 still 1 usbdev1.8_ep82: PM: resume from 0, parent 1-2:1.0 still 1
hci_usb 1-2:1.1: PM: resume from 1, parent 1-2 still 1
usbdev1.8_ep03: PM: resume from 0, parent 1-2:1.1 still 1 usbdev1.8_ep83: PM: resume from 0, parent 1-2:1.1 still 1 usbdev1.8: PM: resume from 0, parent 1-2 still 1
Restarting tasks ... done.
__tx_submit: hci0 tx submit failed urb f22ca854 type 1 err -19 usb 1-2: USB disconnect, address 8
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode [drm] Loading R300 Microcode
BUG: unable to handle kernel NULL pointer dereference at virtual address
00000000
printing eip:
c014787a
*pde = 00000000
Oops: 0000 [#1]
PREEMPT
Modules linked in: michael_mic arc4 ecb blkcipher ieee80211_crypt_tkip
xt_TCPMSS xt_tcpmss xt_tcpudp iptable_mangle ip_tables x_table s ppp_deflate zlib_deflate bsd_comp ppp_async crc_ccitt ppp_generic slhc mt2060 dvb_usb_dib0700 dib7000m dib7000p dvb_usb dvb_core di b3000mc dibx000_common bnep rfcomm hidp hid l2cap capability commoncap eeprom sr_mod sbp2 scsi_mod 8250_pci 8250 serial_core eth1394 hci_usb bluetooth snd_intel8x0m snd_intel8x0 snd_ac97_codec snd_seq_oss ac97_bus snd_seq_midi_event snd_seq snd_seq_device snd_pcm_os s snd_mixer_oss ipw2200 8139too ieee80211 ieee80211_crypt snd_pcm snd_timer iTCO_wdt ehci_hcd mii ohci1394 ieee1394 rtc uhci_hcd snd snd_page_alloc ide_cd i2c_i801 pcspkr cdrom
CPU:    0
EIP:    0060:[<c014787a>]    Not tainted VLI
EFLAGS: 00010203   (2.6.21 #4)
EIP is at put_page+0x5/0xb2
eax: 00000000 ebx: 00000000 ecx: c0317380 edx: f63f70c0
esi: ea6e2680 edi: f784dd84 ebp: f784de48 esp: f784dd4c
ds: 007b es: 007b fs: 00d8 gs: 0033 ss: 0068
Process syslogd (pid: 3160, ti=f784c000 task=f7995070 task.ti=f784c000)
Stack: 00000001 ea6e2680 f784dd84 c02aebed ea6e2680 f784df20 c02aea21
ea6e26b0 c02f58fb 00000036 000001ff f7ca36c0 f7dcfb00 ea6e2680 00000d1f
00000000 00000000 00000000 00000001 00000000 000001ff 0ac3ac80 00000036
c0317380 Call Trace:
 [<c02aebed>] skb_release_data+0x4e/0x80
 [<c02aea21>] kfree_skbmem+0x8/0x61
 [<c02f58fb>] unix_dgram_recvmsg+0x214/0x239
 [<c02a9e24>] sock_recvmsg+0xec/0x107
 [<c0128b23>] autoremove_wake_function+0x0/0x35
 [<c0166775>] core_sys_select+0x1aa/0x2bc
 [<c0160a26>] pipe_write+0x356/0x3ed
 [<c015ae4d>] do_sync_readv_writev+0xc1/0xfe
 [<c02aad15>] sys_recvfrom+0xd7/0x12b
 [<c0128b23>] autoremove_wake_function+0x0/0x35
 [<c02aada0>] sys_recv+0x37/0x3b
 [<c02ab283>] sys_socketcall+0x19c/0x261
 [<c0120dc5>] sigprocmask+0x94/0xb1
 [<c0103cdc>] syscall_call+0x7/0xb
 =======================
Code: 42 c0 e8 66 fe ff ff 89 e0 25 00 e0 ff ff ff 48 14 8b 40 08 a8 08
74 05 e9 18 0f 1b 00 c3 e8 b4 ff ff ff 31 c0 c3 57 56 53 89 c
                                               3 <8b> 00 f6 c4 40 74 0a
Quoted 2 lines
89 d8 5b 5e 5f e9 e9 fb ff ff ff 4b 04 0f
EIP: [<c014787a>] put_page+0x5/0xb2 SS:ESP 0068:f784dd4c

Quoted 3 lines

Good heavens.
Does it oops every time? And does the oops trace always look like this?

Hi Andrew,

let's guess why I marked it Critical ;)

Michal

Quoted 34 lines

Quoted 34 lines
usb 4-1: USB disconnect, address 12
dvb-usb: Leadtek Winfast DTV Dongle (STK7700P based) successfully deinitialized and disconnected.
usb 4-1: new high speed USB device using ehci_hcd and address 14 usb 4-1: configuration #1 chosen from 1 choice
dvb-usb: found a 'Leadtek Winfast DTV Dongle (STK7700P based)' in cold state, will try to load a firmware
dvb-usb: downloading firmware from file 'dvb-usb-dib0700-01.fw'
dib0700: firmware started successfully.
dvb-usb: found a 'Leadtek Winfast DTV Dongle (STK7700P based)' in warm state. i2c_adapter i2c-5: SMBus Quick command not supported, can't probe for chips dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. DVB: registering new adapter (Leadtek Winfast DTV Dongle (STK7700P based)) i2c_adapter i2c-6: SMBus Quick command not supported, can't probe for chips DVB: registering frontend 0 (DiBcom 7000MA/MB/PA/PB/MC)...
MT2060: successfully identified (IF1 = 1220)
dvb-usb: Leadtek Winfast DTV Dongle (STK7700P based) successfully initialized and connected.
usb 1-2: new full speed USB device using uhci_hcd and address 9 usb 1-2: configuration #1 chosen from 1 choice
----------------
Steps to reproduce:
suspend/resume
--
Configure bugmail: http://bugzilla.kernel.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are on the CC list for the bug, or are watching someone who is.

Andrew Morton

author

2007-06-26 17:53 UTC #4 lore raw

Quoted 30 lines · On Tue, 26 Jun 2007 19:42:14 +0200 CIJOML <[email protected]> wrote:

Quoted 30 lines

Quoted 29 lines

EIP is at put_page+0x5/0xb2
eax: 00000000 ebx: 00000000 ecx: c0317380 edx: f63f70c0
esi: ea6e2680 edi: f784dd84 ebp: f784de48 esp: f784dd4c
ds: 007b es: 007b fs: 00d8 gs: 0033 ss: 0068
Process syslogd (pid: 3160, ti=f784c000 task=f7995070 task.ti=f784c000)

Stack: 00000001 ea6e2680 f784dd84 c02aebed ea6e2680 f784df20 c02aea21
ea6e26b0 c02f58fb 00000036 000001ff f7ca36c0 f7dcfb00 ea6e2680 00000d1f
00000000 00000000 00000000 00000001 00000000 000001ff 0ac3ac80 00000036
c0317380 Call Trace:
 [<c02aebed>] skb_release_data+0x4e/0x80
 [<c02aea21>] kfree_skbmem+0x8/0x61
 [<c02f58fb>] unix_dgram_recvmsg+0x214/0x239
 [<c02a9e24>] sock_recvmsg+0xec/0x107
 [<c0128b23>] autoremove_wake_function+0x0/0x35
 [<c0166775>] core_sys_select+0x1aa/0x2bc
 [<c0160a26>] pipe_write+0x356/0x3ed
 [<c015ae4d>] do_sync_readv_writev+0xc1/0xfe
 [<c02aad15>] sys_recvfrom+0xd7/0x12b
 [<c0128b23>] autoremove_wake_function+0x0/0x35
 [<c02aada0>] sys_recv+0x37/0x3b
 [<c02ab283>] sys_socketcall+0x19c/0x261
 [<c0120dc5>] sigprocmask+0x94/0xb1
 [<c0103cdc>] syscall_call+0x7/0xb
 =======================
Code: 42 c0 e8 66 fe ff ff 89 e0 25 00 e0 ff ff ff 48 14 8b 40 08 a8 08
74 05 e9 18 0f 1b 00 c3 e8 b4 ff ff ff 31 c0 c3 57 56 53 89 c
                                               3 <8b> 00 f6 c4 40 74 0a

89 d8 5b 5e 5f e9 e9 fb ff ff ff 4b 04 0f
EIP: [<c014787a>] put_page+0x5/0xb2 SS:ESP 0068:f784dd4c

Quoted 7 lines

Quoted 3 lines
Good heavens.
Does it oops every time? And does the oops trace always look like this?
Hi Andrew,
let's guess why I marked it Critical ;)

dayum. I cannot imagine how a susend/resume can cause a crash in AF_UNIX code. Which network device driver(s) are in use?

Andrew Morton

author

2007-06-26 17:53 UTC #5 lore raw

In reply to CIJOML

Quoted 30 lines · On Tue, 26 Jun 2007 19:42:14 +0200 CIJOML <[email protected]> wrote:

Quoted 30 lines

Quoted 29 lines

Stack: 00000001 ea6e2680 f784dd84 c02aebed ea6e2680 f784df20 c02aea21
ea6e26b0 c02f58fb 00000036 000001ff f7ca36c0 f7dcfb00 ea6e2680 00000d1f
00000000 00000000 00000000 00000001 00000000 000001ff 0ac3ac80 00000036
c0317380 Call Trace:
 [<c02aebed>] skb_release_data+0x4e/0x80
 [<c02aea21>] kfree_skbmem+0x8/0x61
 [<c02f58fb>] unix_dgram_recvmsg+0x214/0x239
 [<c02a9e24>] sock_recvmsg+0xec/0x107
 [<c0128b23>] autoremove_wake_function+0x0/0x35
 [<c0166775>] core_sys_select+0x1aa/0x2bc
 [<c0160a26>] pipe_write+0x356/0x3ed
 [<c015ae4d>] do_sync_readv_writev+0xc1/0xfe
 [<c02aad15>] sys_recvfrom+0xd7/0x12b
 [<c0128b23>] autoremove_wake_function+0x0/0x35
 [<c02aada0>] sys_recv+0x37/0x3b
 [<c02ab283>] sys_socketcall+0x19c/0x261
 [<c0120dc5>] sigprocmask+0x94/0xb1
 [<c0103cdc>] syscall_call+0x7/0xb
 =======================
Code: 42 c0 e8 66 fe ff ff 89 e0 25 00 e0 ff ff ff 48 14 8b 40 08 a8 08
74 05 e9 18 0f 1b 00 c3 e8 b4 ff ff ff 31 c0 c3 57 56 53 89 c
                                               3 <8b> 00 f6 c4 40 74 0a

89 d8 5b 5e 5f e9 e9 fb ff ff ff 4b 04 0f
EIP: [<c014787a>] put_page+0x5/0xb2 SS:ESP 0068:f784dd4c

Quoted 7 lines

Quoted 3 lines
Good heavens.
Does it oops every time? And does the oops trace always look like this?
Hi Andrew,
let's guess why I marked it Critical ;)

dayum. I cannot imagine how a susend/resume can cause a crash in AF_UNIX code. Which network device driver(s) are in use?

Rafael J. Wysocki

2007-06-26 19:52 UTC #6 lore raw

In reply to CIJOML

Quoted 163 lines · CIJOML

Dne úterý 26 červen 2007 19:09 Andrew Morton napsal(a):
Quoted 1 line
On Tue, 26 Jun 2007 08:22:11 -0700 (PDT) [email protected]
Quoted 160 lines · wrote:
Quoted 159 lines
http://bugzilla.kernel.org/show_bug.cgi?id=8678
Summary: Kernel OOPSes when suspend/resume
Product: Power Management
Version: 2.5
KernelVersion: 2.6.21.5
Platform: All
OS/Version: Linux
Tree: Mainline
Status: NEW
Severity: high
Priority: P1
Component: Hibernation/Suspend
AssignedTo: [email protected]
ReportedBy: [email protected]
Most recent kernel where this bug did not occur:
Distribution: Debian Etch
Hardware Environment: Laptop Prestigio (Pentium M) Software Environment: 2.6.21.5, v4l-dvb-b03a5545f8e1 Problem Description:
--------------
Stopping tasks ... done.
Shrinking memory... done (0 pages freed)
Freed 0 kbytes in 0.02 seconds (0.00 MB/s)
Suspending console(s)
dvb_usb_dib0700 4-1:1.0: no suspend for driver dvb_usb_dib0700?
eth2: Going into suspend...
ACPI: PCI interrupt for device 0000:02:0c.0 disabled
radeonfb (0000:01:00.0): suspending for event: 1...
ACPI: PCI interrupt for device 0000:00:1f.6 disabled
ACPI: PCI interrupt for device 0000:00:1f.5 disabled
ACPI: PCI interrupt for device 0000:00:1d.7 disabled
ACPI: PCI interrupt for device 0000:00:1d.2 disabled
ACPI: PCI interrupt for device 0000:00:1d.1 disabled
ACPI: PCI interrupt for device 0000:00:1d.0 disabled
swsusp: critical section:
swsusp: Need to copy 112337 pages
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.0 to 64
usb usb1: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.1 to 64
usb usb2: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.2 to 64
usb usb3: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.7 to 64
usb usb4: root hub lost power or was reset
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PM: Writing back config space on device 0000:00:1f.5 at offset 1 (was 2900007, writing 2900003)
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1f.5 to 64
PM: Writing back config space on device 0000:00:1f.6 at offset 1 (was 2900005, writing 2900001)
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1f.6 to 64 radeonfb (0000:01:00.0): resuming from state: 1...
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[ffdff800-ffdfffff] Max Packet=[2048] IR/IT contexts=[4/8]
eth0: link down
Yenta O2: res at 0x94/0xD4: 00/ea
Yenta O2: enabling read prefetch/write burst
eth2: Coming out of suspend...
ACPI: PCI Interrupt 0000:02:0c.0[A] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
pnp: Failed to activate device 00:03.
pnp: Failed to activate device 00:04.
usbdev4.12_ep00: PM: resume from 0, parent 4-1 still 1
dvb_usb_dib0700 4-1:1.0: PM: resume from 1, parent 4-1 still 1 i2c_adapter i2c-5: PM: resume from 0, parent 4-1 still 1
usbdev4.12_ep01: PM: resume from 0, parent 4-1:1.0 still 1 usbdev4.12_ep81: PM: resume from 0, parent 4-1:1.0 still 1 usbdev4.12_ep82: PM: resume from 0, parent 4-1:1.0 still 1 usbdev4.12_ep83: PM: resume from 0, parent 4-1:1.0 still 1 usbdev4.12: PM: resume from 0, parent 4-1 still 1 usbdev1.8_ep00: PM: resume from 0, parent 1-2 still 1
hci_usb 1-2:1.0: PM: resume from 1, parent 1-2 still 1
hci0: PM: resume from 0, parent 1-2:1.0 still 1 usbdev1.8_ep81: PM: resume from 0, parent 1-2:1.0 still 1 usbdev1.8_ep02: PM: resume from 0, parent 1-2:1.0 still 1 usbdev1.8_ep82: PM: resume from 0, parent 1-2:1.0 still 1
hci_usb 1-2:1.1: PM: resume from 1, parent 1-2 still 1
usbdev1.8_ep03: PM: resume from 0, parent 1-2:1.1 still 1 usbdev1.8_ep83: PM: resume from 0, parent 1-2:1.1 still 1 usbdev1.8: PM: resume from 0, parent 1-2 still 1
Restarting tasks ... done.
__tx_submit: hci0 tx submit failed urb f22ca854 type 1 err -19 usb 1-2: USB disconnect, address 8
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode [drm] Loading R300 Microcode
BUG: unable to handle kernel NULL pointer dereference at virtual address
00000000
printing eip:
c014787a
*pde = 00000000
Oops: 0000 [#1]
PREEMPT
Modules linked in: michael_mic arc4 ecb blkcipher ieee80211_crypt_tkip
xt_TCPMSS xt_tcpmss xt_tcpudp iptable_mangle ip_tables x_table s ppp_deflate zlib_deflate bsd_comp ppp_async crc_ccitt ppp_generic slhc mt2060 dvb_usb_dib0700 dib7000m dib7000p dvb_usb dvb_core di b3000mc dibx000_common bnep rfcomm hidp hid l2cap capability commoncap eeprom sr_mod sbp2 scsi_mod 8250_pci 8250 serial_core eth1394 hci_usb bluetooth snd_intel8x0m snd_intel8x0 snd_ac97_codec snd_seq_oss ac97_bus snd_seq_midi_event snd_seq snd_seq_device snd_pcm_os s snd_mixer_oss ipw2200 8139too ieee80211 ieee80211_crypt snd_pcm snd_timer iTCO_wdt ehci_hcd mii ohci1394 ieee1394 rtc uhci_hcd snd snd_page_alloc ide_cd i2c_i801 pcspkr cdrom
CPU:    0
EIP:    0060:[<c014787a>]    Not tainted VLI
EFLAGS: 00010203   (2.6.21 #4)
EIP is at put_page+0x5/0xb2
eax: 00000000 ebx: 00000000 ecx: c0317380 edx: f63f70c0
esi: ea6e2680 edi: f784dd84 ebp: f784de48 esp: f784dd4c
ds: 007b es: 007b fs: 00d8 gs: 0033 ss: 0068
Process syslogd (pid: 3160, ti=f784c000 task=f7995070 task.ti=f784c000)
Stack: 00000001 ea6e2680 f784dd84 c02aebed ea6e2680 f784df20 c02aea21
ea6e26b0 c02f58fb 00000036 000001ff f7ca36c0 f7dcfb00 ea6e2680 00000d1f
00000000 00000000 00000000 00000001 00000000 000001ff 0ac3ac80 00000036
c0317380 Call Trace:
 [<c02aebed>] skb_release_data+0x4e/0x80
 [<c02aea21>] kfree_skbmem+0x8/0x61
 [<c02f58fb>] unix_dgram_recvmsg+0x214/0x239
 [<c02a9e24>] sock_recvmsg+0xec/0x107
 [<c0128b23>] autoremove_wake_function+0x0/0x35
 [<c0166775>] core_sys_select+0x1aa/0x2bc
 [<c0160a26>] pipe_write+0x356/0x3ed
 [<c015ae4d>] do_sync_readv_writev+0xc1/0xfe
 [<c02aad15>] sys_recvfrom+0xd7/0x12b
 [<c0128b23>] autoremove_wake_function+0x0/0x35
 [<c02aada0>] sys_recv+0x37/0x3b
 [<c02ab283>] sys_socketcall+0x19c/0x261
 [<c0120dc5>] sigprocmask+0x94/0xb1
 [<c0103cdc>] syscall_call+0x7/0xb
 =======================
Code: 42 c0 e8 66 fe ff ff 89 e0 25 00 e0 ff ff ff 48 14 8b 40 08 a8 08
74 05 e9 18 0f 1b 00 c3 e8 b4 ff ff ff 31 c0 c3 57 56 53 89 c
                                               3 <8b> 00 f6 c4 40 74 0a
89 d8 5b 5e 5f e9 e9 fb ff ff ff 4b 04 0f
EIP: [<c014787a>] put_page+0x5/0xb2 SS:ESP 0068:f784dd4c

Quoted 7 lines

Quoted 3 lines
Good heavens.
Does it oops every time? And does the oops trace always look like this?
Hi Andrew,
let's guess why I marked it Critical ;)

Can you please retest without DRM?

Greetings,
Rafael

Signature · 1 line

"Premature optimization is the root of all evil." - Donald Knuth

CIJOML

2007-06-26 21:16 UTC #7 lore raw

Dne úterý 26 červen 2007 21:59 Rafael J. Wysocki napsal(a):

Quoted 170 lines · CIJOML

Quoted 169 lines
Dne úterý 26 červen 2007 19:09 Andrew Morton napsal(a):
Quoted 2 lines
On Tue, 26 Jun 2007 08:22:11 -0700 (PDT)
[email protected]
Quoted 163 lines · wrote:
Quoted 155 lines
http://bugzilla.kernel.org/show_bug.cgi?id=8678
Summary: Kernel OOPSes when suspend/resume
Product: Power Management
Version: 2.5
KernelVersion: 2.6.21.5
Platform: All
OS/Version: Linux
Tree: Mainline
Status: NEW
Severity: high
Priority: P1
Component: Hibernation/Suspend
AssignedTo: [email protected]
ReportedBy: [email protected]
Most recent kernel where this bug did not occur:
Distribution: Debian Etch
Hardware Environment: Laptop Prestigio (Pentium M) Software Environment: 2.6.21.5, v4l-dvb-b03a5545f8e1 Problem Description:
--------------
Stopping tasks ... done.
Shrinking memory... done (0 pages freed)
Freed 0 kbytes in 0.02 seconds (0.00 MB/s)
Suspending console(s)
dvb_usb_dib0700 4-1:1.0: no suspend for driver dvb_usb_dib0700?
eth2: Going into suspend...
ACPI: PCI interrupt for device 0000:02:0c.0 disabled radeonfb (0000:01:00.0): suspending for event: 1...
ACPI: PCI interrupt for device 0000:00:1f.6 disabled
ACPI: PCI interrupt for device 0000:00:1f.5 disabled
ACPI: PCI interrupt for device 0000:00:1d.7 disabled
ACPI: PCI interrupt for device 0000:00:1d.2 disabled
ACPI: PCI interrupt for device 0000:00:1d.1 disabled
ACPI: PCI interrupt for device 0000:00:1d.0 disabled
swsusp: critical section:
swsusp: Need to copy 112337 pages
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.0 to 64 usb usb1: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.1 to 64 usb usb2: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.2 to 64 usb usb3: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.7 to 64 usb usb4: root hub lost power or was reset
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PM: Writing back config space on device 0000:00:1f.5 at offset 1 (was 2900007, writing 2900003)
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1f.5 to 64
PM: Writing back config space on device 0000:00:1f.6 at offset 1 (was 2900005, writing 2900001)
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1f.6 to 64 radeonfb (0000:01:00.0): resuming from state: 1...
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[ffdff800-ffdfffff] Max Packet=[2048] IR/IT contexts=[4/8]
eth0: link down
Yenta O2: res at 0x94/0xD4: 00/ea
Yenta O2: enabling read prefetch/write burst
eth2: Coming out of suspend...
ACPI: PCI Interrupt 0000:02:0c.0[A] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
pnp: Failed to activate device 00:03.
pnp: Failed to activate device 00:04.
usbdev4.12_ep00: PM: resume from 0, parent 4-1 still 1
dvb_usb_dib0700 4-1:1.0: PM: resume from 1, parent 4-1 still 1 i2c_adapter i2c-5: PM: resume from 0, parent 4-1 still 1
usbdev4.12_ep01: PM: resume from 0, parent 4-1:1.0 still 1 usbdev4.12_ep81: PM: resume from 0, parent 4-1:1.0 still 1 usbdev4.12_ep82: PM: resume from 0, parent 4-1:1.0 still 1 usbdev4.12_ep83: PM: resume from 0, parent 4-1:1.0 still 1 usbdev4.12: PM: resume from 0, parent 4-1 still 1 usbdev1.8_ep00: PM: resume from 0, parent 1-2 still 1
hci_usb 1-2:1.0: PM: resume from 1, parent 1-2 still 1
hci0: PM: resume from 0, parent 1-2:1.0 still 1 usbdev1.8_ep81: PM: resume from 0, parent 1-2:1.0 still 1 usbdev1.8_ep02: PM: resume from 0, parent 1-2:1.0 still 1 usbdev1.8_ep82: PM: resume from 0, parent 1-2:1.0 still 1
hci_usb 1-2:1.1: PM: resume from 1, parent 1-2 still 1
usbdev1.8_ep03: PM: resume from 0, parent 1-2:1.1 still 1 usbdev1.8_ep83: PM: resume from 0, parent 1-2:1.1 still 1 usbdev1.8: PM: resume from 0, parent 1-2 still 1
Restarting tasks ... done.
__tx_submit: hci0 tx submit failed urb f22ca854 type 1 err -19 usb 1-2: USB disconnect, address 8
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode [drm] Loading R300 Microcode
BUG: unable to handle kernel NULL pointer dereference at virtual
address 00000000
printing eip:
c014787a
*pde = 00000000
Oops: 0000 [#1]
PREEMPT
Modules linked in: michael_mic arc4 ecb blkcipher
ieee80211_crypt_tkip xt_TCPMSS xt_tcpmss xt_tcpudp iptable_mangle ip_tables x_table s ppp_deflate zlib_deflate bsd_comp ppp_async crc_ccitt ppp_generic slhc mt2060 dvb_usb_dib0700 dib7000m dib7000p dvb_usb dvb_core di b3000mc dibx000_common bnep rfcomm hidp hid l2cap capability commoncap eeprom sr_mod sbp2 scsi_mod 8250_pci 8250 serial_core eth1394 hci_usb bluetooth snd_intel8x0m snd_intel8x0 snd_ac97_codec snd_seq_oss ac97_bus snd_seq_midi_event snd_seq snd_seq_device snd_pcm_os s snd_mixer_oss ipw2200 8139too ieee80211 ieee80211_crypt snd_pcm snd_timer iTCO_wdt ehci_hcd mii ohci1394 ieee1394 rtc uhci_hcd snd snd_page_alloc ide_cd i2c_i801 pcspkr cdrom
CPU:    0
EIP:    0060:[<c014787a>]    Not tainted VLI
EFLAGS: 00010203   (2.6.21 #4)
EIP is at put_page+0x5/0xb2
eax: 00000000 ebx: 00000000 ecx: c0317380 edx: f63f70c0
esi: ea6e2680 edi: f784dd84 ebp: f784de48 esp: f784dd4c
ds: 007b es: 007b fs: 00d8 gs: 0033 ss: 0068
Process syslogd (pid: 3160, ti=f784c000 task=f7995070 task.ti=f784c000) Stack: 00000001 ea6e2680 f784dd84 c02aebed ea6e2680 f784df20 c02aea21 ea6e26b0 c02f58fb 00000036 000001ff f7ca36c0 f7dcfb00 ea6e2680 00000d1f 00000000 00000000 00000000 00000001 00000000 000001ff 0ac3ac80 00000036 c0317380 Call Trace:
 [<c02aebed>] skb_release_data+0x4e/0x80
 [<c02aea21>] kfree_skbmem+0x8/0x61
 [<c02f58fb>] unix_dgram_recvmsg+0x214/0x239
 [<c02a9e24>] sock_recvmsg+0xec/0x107
 [<c0128b23>] autoremove_wake_function+0x0/0x35
 [<c0166775>] core_sys_select+0x1aa/0x2bc
 [<c0160a26>] pipe_write+0x356/0x3ed
 [<c015ae4d>] do_sync_readv_writev+0xc1/0xfe
 [<c02aad15>] sys_recvfrom+0xd7/0x12b
 [<c0128b23>] autoremove_wake_function+0x0/0x35
 [<c02aada0>] sys_recv+0x37/0x3b
 [<c02ab283>] sys_socketcall+0x19c/0x261
 [<c0120dc5>] sigprocmask+0x94/0xb1
 [<c0103cdc>] syscall_call+0x7/0xb
 =======================
Code: 42 c0 e8 66 fe ff ff 89 e0 25 00 e0 ff ff ff 48 14 8b 40 08 a8
Quoted 3 lines
08 74 05 e9 18 0f 1b 00 c3 e8 b4 ff ff ff 31 c0 c3 57 56 53 89 c 3 <8b> 00 f6 c4 40 74 0a 89 d8 5b 5e 5f e9 e9 fb ff ff ff 4b 04 0f
EIP: [<c014787a>] put_page+0x5/0xb2 SS:ESP 0068:f784dd4c
Good heavens.
Does it oops every time? And does the oops trace always look like this?

Quoted 8 lines

Quoted 3 lines
Hi Andrew,
let's guess why I marked it Critical ;)
Can you please retest without DRM?
Greetings,
Rafael

Ehm What is DRM??? Digital Right Management????

Michal

CIJOML

2007-06-26 21:16 UTC #8 lore raw

In reply to Rafael J. Wysocki

Dne úterý 26 červen 2007 21:59 Rafael J. Wysocki napsal(a):

Quoted 170 lines · CIJOML

Quoted 169 lines
Dne úterý 26 červen 2007 19:09 Andrew Morton napsal(a):
Quoted 2 lines
On Tue, 26 Jun 2007 08:22:11 -0700 (PDT)
[email protected]
Quoted 163 lines · wrote:
Quoted 155 lines
http://bugzilla.kernel.org/show_bug.cgi?id=8678
Summary: Kernel OOPSes when suspend/resume
Product: Power Management
Version: 2.5
KernelVersion: 2.6.21.5
Platform: All
OS/Version: Linux
Tree: Mainline
Status: NEW
Severity: high
Priority: P1
Component: Hibernation/Suspend
AssignedTo: [email protected]
ReportedBy: [email protected]
Most recent kernel where this bug did not occur:
Distribution: Debian Etch
Hardware Environment: Laptop Prestigio (Pentium M) Software Environment: 2.6.21.5, v4l-dvb-b03a5545f8e1 Problem Description:
--------------
Stopping tasks ... done.
Shrinking memory... done (0 pages freed)
Freed 0 kbytes in 0.02 seconds (0.00 MB/s)
Suspending console(s)
dvb_usb_dib0700 4-1:1.0: no suspend for driver dvb_usb_dib0700?
eth2: Going into suspend...
ACPI: PCI interrupt for device 0000:02:0c.0 disabled radeonfb (0000:01:00.0): suspending for event: 1...
ACPI: PCI interrupt for device 0000:00:1f.6 disabled
ACPI: PCI interrupt for device 0000:00:1f.5 disabled
ACPI: PCI interrupt for device 0000:00:1d.7 disabled
ACPI: PCI interrupt for device 0000:00:1d.2 disabled
ACPI: PCI interrupt for device 0000:00:1d.1 disabled
ACPI: PCI interrupt for device 0000:00:1d.0 disabled
swsusp: critical section:
swsusp: Need to copy 112337 pages
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.0 to 64 usb usb1: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.1 to 64 usb usb2: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.2 to 64 usb usb3: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.7 to 64 usb usb4: root hub lost power or was reset
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PM: Writing back config space on device 0000:00:1f.5 at offset 1 (was 2900007, writing 2900003)
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1f.5 to 64
PM: Writing back config space on device 0000:00:1f.6 at offset 1 (was 2900005, writing 2900001)
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1f.6 to 64 radeonfb (0000:01:00.0): resuming from state: 1...
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[ffdff800-ffdfffff] Max Packet=[2048] IR/IT contexts=[4/8]
eth0: link down
Yenta O2: res at 0x94/0xD4: 00/ea
Yenta O2: enabling read prefetch/write burst
eth2: Coming out of suspend...
ACPI: PCI Interrupt 0000:02:0c.0[A] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
pnp: Failed to activate device 00:03.
pnp: Failed to activate device 00:04.
usbdev4.12_ep00: PM: resume from 0, parent 4-1 still 1
dvb_usb_dib0700 4-1:1.0: PM: resume from 1, parent 4-1 still 1 i2c_adapter i2c-5: PM: resume from 0, parent 4-1 still 1
usbdev4.12_ep01: PM: resume from 0, parent 4-1:1.0 still 1 usbdev4.12_ep81: PM: resume from 0, parent 4-1:1.0 still 1 usbdev4.12_ep82: PM: resume from 0, parent 4-1:1.0 still 1 usbdev4.12_ep83: PM: resume from 0, parent 4-1:1.0 still 1 usbdev4.12: PM: resume from 0, parent 4-1 still 1 usbdev1.8_ep00: PM: resume from 0, parent 1-2 still 1
hci_usb 1-2:1.0: PM: resume from 1, parent 1-2 still 1
hci0: PM: resume from 0, parent 1-2:1.0 still 1 usbdev1.8_ep81: PM: resume from 0, parent 1-2:1.0 still 1 usbdev1.8_ep02: PM: resume from 0, parent 1-2:1.0 still 1 usbdev1.8_ep82: PM: resume from 0, parent 1-2:1.0 still 1
hci_usb 1-2:1.1: PM: resume from 1, parent 1-2 still 1
usbdev1.8_ep03: PM: resume from 0, parent 1-2:1.1 still 1 usbdev1.8_ep83: PM: resume from 0, parent 1-2:1.1 still 1 usbdev1.8: PM: resume from 0, parent 1-2 still 1
Restarting tasks ... done.
__tx_submit: hci0 tx submit failed urb f22ca854 type 1 err -19 usb 1-2: USB disconnect, address 8
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode [drm] Loading R300 Microcode
BUG: unable to handle kernel NULL pointer dereference at virtual
address 00000000
printing eip:
c014787a
*pde = 00000000
Oops: 0000 [#1]
PREEMPT
Modules linked in: michael_mic arc4 ecb blkcipher
ieee80211_crypt_tkip xt_TCPMSS xt_tcpmss xt_tcpudp iptable_mangle ip_tables x_table s ppp_deflate zlib_deflate bsd_comp ppp_async crc_ccitt ppp_generic slhc mt2060 dvb_usb_dib0700 dib7000m dib7000p dvb_usb dvb_core di b3000mc dibx000_common bnep rfcomm hidp hid l2cap capability commoncap eeprom sr_mod sbp2 scsi_mod 8250_pci 8250 serial_core eth1394 hci_usb bluetooth snd_intel8x0m snd_intel8x0 snd_ac97_codec snd_seq_oss ac97_bus snd_seq_midi_event snd_seq snd_seq_device snd_pcm_os s snd_mixer_oss ipw2200 8139too ieee80211 ieee80211_crypt snd_pcm snd_timer iTCO_wdt ehci_hcd mii ohci1394 ieee1394 rtc uhci_hcd snd snd_page_alloc ide_cd i2c_i801 pcspkr cdrom
CPU:    0
EIP:    0060:[<c014787a>]    Not tainted VLI
EFLAGS: 00010203   (2.6.21 #4)
EIP is at put_page+0x5/0xb2
eax: 00000000 ebx: 00000000 ecx: c0317380 edx: f63f70c0
esi: ea6e2680 edi: f784dd84 ebp: f784de48 esp: f784dd4c
ds: 007b es: 007b fs: 00d8 gs: 0033 ss: 0068
Process syslogd (pid: 3160, ti=f784c000 task=f7995070 task.ti=f784c000) Stack: 00000001 ea6e2680 f784dd84 c02aebed ea6e2680 f784df20 c02aea21 ea6e26b0 c02f58fb 00000036 000001ff f7ca36c0 f7dcfb00 ea6e2680 00000d1f 00000000 00000000 00000000 00000001 00000000 000001ff 0ac3ac80 00000036 c0317380 Call Trace:
 [<c02aebed>] skb_release_data+0x4e/0x80
 [<c02aea21>] kfree_skbmem+0x8/0x61
 [<c02f58fb>] unix_dgram_recvmsg+0x214/0x239
 [<c02a9e24>] sock_recvmsg+0xec/0x107
 [<c0128b23>] autoremove_wake_function+0x0/0x35
 [<c0166775>] core_sys_select+0x1aa/0x2bc
 [<c0160a26>] pipe_write+0x356/0x3ed
 [<c015ae4d>] do_sync_readv_writev+0xc1/0xfe
 [<c02aad15>] sys_recvfrom+0xd7/0x12b
 [<c0128b23>] autoremove_wake_function+0x0/0x35
 [<c02aada0>] sys_recv+0x37/0x3b
 [<c02ab283>] sys_socketcall+0x19c/0x261
 [<c0120dc5>] sigprocmask+0x94/0xb1
 [<c0103cdc>] syscall_call+0x7/0xb
 =======================
Code: 42 c0 e8 66 fe ff ff 89 e0 25 00 e0 ff ff ff 48 14 8b 40 08 a8
Quoted 3 lines
08 74 05 e9 18 0f 1b 00 c3 e8 b4 ff ff ff 31 c0 c3 57 56 53 89 c 3 <8b> 00 f6 c4 40 74 0a 89 d8 5b 5e 5f e9 e9 fb ff ff ff 4b 04 0f
EIP: [<c014787a>] put_page+0x5/0xb2 SS:ESP 0068:f784dd4c
Good heavens.
Does it oops every time? And does the oops trace always look like this?

Quoted 8 lines

Quoted 3 lines
Hi Andrew,
let's guess why I marked it Critical ;)
Can you please retest without DRM?
Greetings,
Rafael

Ehm What is DRM??? Digital Right Management????

Michal

Andrew Morton

author

2007-06-26 21:25 UTC #9 lore raw

Quoted 6 lines · On Tue, 26 Jun 2007 23:16:14 +0200 CIJOML <[email protected]> wrote:

Quoted 4 lines
Can you please retest without DRM?
Greetings,
Rafael
Ehm What is DRM??? Digital Right Management????

Direct-rendering manager: the thing which does accelerated 3d in X.

Disable CONFIG_DRM in your .config.

Andrew Morton

author

2007-06-26 21:26 UTC #10 lore raw

In reply to CIJOML

Quoted 6 lines · On Tue, 26 Jun 2007 23:16:14 +0200 CIJOML <[email protected]> wrote:

Quoted 4 lines
Can you please retest without DRM?
Greetings,
Rafael
Ehm What is DRM??? Digital Right Management????

Direct-rendering manager: the thing which does accelerated 3d in X.

Disable CONFIG_DRM in your .config.

Pavel Machek

2007-06-26 22:34 UTC #11 lore raw

In reply to CIJOML

Hi!

Quoted 20 lines

Quoted 20 lines
Quoted 20 lines
Quoted 13 lines
Quoted 12 lines
PREEMPT
Modules linked in: michael_mic arc4 ecb blkcipher
ieee80211_crypt_tkip xt_TCPMSS xt_tcpmss xt_tcpudp iptable_mangle ip_tables x_table s ppp_deflate zlib_deflate bsd_comp ppp_async crc_ccitt ppp_generic slhc mt2060 dvb_usb_dib0700 dib7000m dib7000p dvb_usb dvb_core di b3000mc dibx000_common bnep rfcomm hidp hid l2cap capability commoncap eeprom sr_mod sbp2 scsi_mod 8250_pci 8250 serial_core eth1394 hci_usb bluetooth snd_intel8x0m snd_intel8x0 snd_ac97_codec snd_seq_oss ac97_bus snd_seq_midi_event snd_seq snd_seq_device snd_pcm_os s snd_mixer_oss ipw2200 8139too ieee80211 ieee80211_crypt snd_pcm snd_timer iTCO_wdt ehci_hcd mii ohci1394 ieee1394 rtc uhci_hcd snd snd_page_alloc ide_cd i2c_i801 pcspkr cdrom
Quoted 4 lines
Good heavens.
Does it oops every time? And does the oops trace always look like this?
Hi Andrew,

Quoted 8 lines

Quoted 6 lines
Quoted 1 line
let's guess why I marked it Critical ;)
Can you please retest without DRM?
Greetings,
Rafael
Ehm What is DRM??? Digital Right Management????

(Direct Rendering M... part of 3d acceleration)

Just try to unload as many modules as possible, perhaps we'll find the one causing it.
Pavel

Signature · 2 lines

(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

Pavel Machek

2007-06-26 22:34 UTC #12 lore raw

In reply to CIJOML

Hi!

Quoted 20 lines

Quoted 20 lines
Quoted 20 lines
Quoted 13 lines
Quoted 12 lines
PREEMPT
Modules linked in: michael_mic arc4 ecb blkcipher
ieee80211_crypt_tkip xt_TCPMSS xt_tcpmss xt_tcpudp iptable_mangle ip_tables x_table s ppp_deflate zlib_deflate bsd_comp ppp_async crc_ccitt ppp_generic slhc mt2060 dvb_usb_dib0700 dib7000m dib7000p dvb_usb dvb_core di b3000mc dibx000_common bnep rfcomm hidp hid l2cap capability commoncap eeprom sr_mod sbp2 scsi_mod 8250_pci 8250 serial_core eth1394 hci_usb bluetooth snd_intel8x0m snd_intel8x0 snd_ac97_codec snd_seq_oss ac97_bus snd_seq_midi_event snd_seq snd_seq_device snd_pcm_os s snd_mixer_oss ipw2200 8139too ieee80211 ieee80211_crypt snd_pcm snd_timer iTCO_wdt ehci_hcd mii ohci1394 ieee1394 rtc uhci_hcd snd snd_page_alloc ide_cd i2c_i801 pcspkr cdrom
Quoted 4 lines
Good heavens.
Does it oops every time? And does the oops trace always look like this?
Hi Andrew,

Quoted 8 lines

Quoted 6 lines
Quoted 1 line
let's guess why I marked it Critical ;)
Can you please retest without DRM?
Greetings,
Rafael
Ehm What is DRM??? Digital Right Management????

(Direct Rendering M... part of 3d acceleration)

Just try to unload as many modules as possible, perhaps we'll find the one causing it.
Pavel

Signature · 2 lines

(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

Rafael J. Wysocki

2007-06-26 19:59 UTC #13 lore raw

In reply to CIJOML

Quoted 163 lines · CIJOML

Dne úterý 26 červen 2007 19:09 Andrew Morton napsal(a):
Quoted 1 line
On Tue, 26 Jun 2007 08:22:11 -0700 (PDT) [email protected]
Quoted 160 lines · wrote:
Quoted 159 lines
http://bugzilla.kernel.org/show_bug.cgi?id=8678
Summary: Kernel OOPSes when suspend/resume
Product: Power Management
Version: 2.5
KernelVersion: 2.6.21.5
Platform: All
OS/Version: Linux
Tree: Mainline
Status: NEW
Severity: high
Priority: P1
Component: Hibernation/Suspend
AssignedTo: [email protected]
ReportedBy: [email protected]
Most recent kernel where this bug did not occur:
Distribution: Debian Etch
Hardware Environment: Laptop Prestigio (Pentium M) Software Environment: 2.6.21.5, v4l-dvb-b03a5545f8e1 Problem Description:
--------------
Stopping tasks ... done.
Shrinking memory... done (0 pages freed)
Freed 0 kbytes in 0.02 seconds (0.00 MB/s)
Suspending console(s)
dvb_usb_dib0700 4-1:1.0: no suspend for driver dvb_usb_dib0700?
eth2: Going into suspend...
ACPI: PCI interrupt for device 0000:02:0c.0 disabled
radeonfb (0000:01:00.0): suspending for event: 1...
ACPI: PCI interrupt for device 0000:00:1f.6 disabled
ACPI: PCI interrupt for device 0000:00:1f.5 disabled
ACPI: PCI interrupt for device 0000:00:1d.7 disabled
ACPI: PCI interrupt for device 0000:00:1d.2 disabled
ACPI: PCI interrupt for device 0000:00:1d.1 disabled
ACPI: PCI interrupt for device 0000:00:1d.0 disabled
swsusp: critical section:
swsusp: Need to copy 112337 pages
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.0 to 64
usb usb1: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.1 to 64
usb usb2: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.2 to 64
usb usb3: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.7 to 64
usb usb4: root hub lost power or was reset
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PM: Writing back config space on device 0000:00:1f.5 at offset 1 (was 2900007, writing 2900003)
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1f.5 to 64
PM: Writing back config space on device 0000:00:1f.6 at offset 1 (was 2900005, writing 2900001)
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1f.6 to 64 radeonfb (0000:01:00.0): resuming from state: 1...
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[ffdff800-ffdfffff] Max Packet=[2048] IR/IT contexts=[4/8]
eth0: link down
Yenta O2: res at 0x94/0xD4: 00/ea
Yenta O2: enabling read prefetch/write burst
eth2: Coming out of suspend...
ACPI: PCI Interrupt 0000:02:0c.0[A] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
pnp: Failed to activate device 00:03.
pnp: Failed to activate device 00:04.
usbdev4.12_ep00: PM: resume from 0, parent 4-1 still 1
dvb_usb_dib0700 4-1:1.0: PM: resume from 1, parent 4-1 still 1 i2c_adapter i2c-5: PM: resume from 0, parent 4-1 still 1
usbdev4.12_ep01: PM: resume from 0, parent 4-1:1.0 still 1 usbdev4.12_ep81: PM: resume from 0, parent 4-1:1.0 still 1 usbdev4.12_ep82: PM: resume from 0, parent 4-1:1.0 still 1 usbdev4.12_ep83: PM: resume from 0, parent 4-1:1.0 still 1 usbdev4.12: PM: resume from 0, parent 4-1 still 1 usbdev1.8_ep00: PM: resume from 0, parent 1-2 still 1
hci_usb 1-2:1.0: PM: resume from 1, parent 1-2 still 1
hci0: PM: resume from 0, parent 1-2:1.0 still 1 usbdev1.8_ep81: PM: resume from 0, parent 1-2:1.0 still 1 usbdev1.8_ep02: PM: resume from 0, parent 1-2:1.0 still 1 usbdev1.8_ep82: PM: resume from 0, parent 1-2:1.0 still 1
hci_usb 1-2:1.1: PM: resume from 1, parent 1-2 still 1
usbdev1.8_ep03: PM: resume from 0, parent 1-2:1.1 still 1 usbdev1.8_ep83: PM: resume from 0, parent 1-2:1.1 still 1 usbdev1.8: PM: resume from 0, parent 1-2 still 1
Restarting tasks ... done.
__tx_submit: hci0 tx submit failed urb f22ca854 type 1 err -19 usb 1-2: USB disconnect, address 8
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode [drm] Loading R300 Microcode
BUG: unable to handle kernel NULL pointer dereference at virtual address
00000000
printing eip:
c014787a
*pde = 00000000
Oops: 0000 [#1]
PREEMPT
Modules linked in: michael_mic arc4 ecb blkcipher ieee80211_crypt_tkip
xt_TCPMSS xt_tcpmss xt_tcpudp iptable_mangle ip_tables x_table s ppp_deflate zlib_deflate bsd_comp ppp_async crc_ccitt ppp_generic slhc mt2060 dvb_usb_dib0700 dib7000m dib7000p dvb_usb dvb_core di b3000mc dibx000_common bnep rfcomm hidp hid l2cap capability commoncap eeprom sr_mod sbp2 scsi_mod 8250_pci 8250 serial_core eth1394 hci_usb bluetooth snd_intel8x0m snd_intel8x0 snd_ac97_codec snd_seq_oss ac97_bus snd_seq_midi_event snd_seq snd_seq_device snd_pcm_os s snd_mixer_oss ipw2200 8139too ieee80211 ieee80211_crypt snd_pcm snd_timer iTCO_wdt ehci_hcd mii ohci1394 ieee1394 rtc uhci_hcd snd snd_page_alloc ide_cd i2c_i801 pcspkr cdrom
CPU:    0
EIP:    0060:[<c014787a>]    Not tainted VLI
EFLAGS: 00010203   (2.6.21 #4)
EIP is at put_page+0x5/0xb2
eax: 00000000 ebx: 00000000 ecx: c0317380 edx: f63f70c0
esi: ea6e2680 edi: f784dd84 ebp: f784de48 esp: f784dd4c
ds: 007b es: 007b fs: 00d8 gs: 0033 ss: 0068
Process syslogd (pid: 3160, ti=f784c000 task=f7995070 task.ti=f784c000)
Stack: 00000001 ea6e2680 f784dd84 c02aebed ea6e2680 f784df20 c02aea21
ea6e26b0 c02f58fb 00000036 000001ff f7ca36c0 f7dcfb00 ea6e2680 00000d1f
00000000 00000000 00000000 00000001 00000000 000001ff 0ac3ac80 00000036
c0317380 Call Trace:
 [<c02aebed>] skb_release_data+0x4e/0x80
 [<c02aea21>] kfree_skbmem+0x8/0x61
 [<c02f58fb>] unix_dgram_recvmsg+0x214/0x239
 [<c02a9e24>] sock_recvmsg+0xec/0x107
 [<c0128b23>] autoremove_wake_function+0x0/0x35
 [<c0166775>] core_sys_select+0x1aa/0x2bc
 [<c0160a26>] pipe_write+0x356/0x3ed
 [<c015ae4d>] do_sync_readv_writev+0xc1/0xfe
 [<c02aad15>] sys_recvfrom+0xd7/0x12b
 [<c0128b23>] autoremove_wake_function+0x0/0x35
 [<c02aada0>] sys_recv+0x37/0x3b
 [<c02ab283>] sys_socketcall+0x19c/0x261
 [<c0120dc5>] sigprocmask+0x94/0xb1
 [<c0103cdc>] syscall_call+0x7/0xb
 =======================
Code: 42 c0 e8 66 fe ff ff 89 e0 25 00 e0 ff ff ff 48 14 8b 40 08 a8 08
74 05 e9 18 0f 1b 00 c3 e8 b4 ff ff ff 31 c0 c3 57 56 53 89 c
                                               3 <8b> 00 f6 c4 40 74 0a
89 d8 5b 5e 5f e9 e9 fb ff ff ff 4b 04 0f
EIP: [<c014787a>] put_page+0x5/0xb2 SS:ESP 0068:f784dd4c

Quoted 7 lines

Quoted 3 lines
Good heavens.
Does it oops every time? And does the oops trace always look like this?
Hi Andrew,
let's guess why I marked it Critical ;)

Can you please retest without DRM?

Greetings,
Rafael

Signature · 1 line

"Premature optimization is the root of all evil." - Donald Knuth