harddisk speed: 2.4.24 20+% faster then 2.6.3
I've been checking, rechecking but cannot explain why a "vannilla" debian install kernel (sid-testing install cdrom) is faster then "Feisty Dunnart" on the same hardware.
hardware: Mini-itx with 1Ghz via-C3
200GB udma harddisk.
2.4.24:
Timing buffered disk reads: 150 MB in 3.01 seconds = 49.83 MB/sec
2.6.3 (vanilla):
Timing buffered disk reads: 102 MB in 3.05 seconds = 33.40 MB/sec
2.6.3-mm4:
Timing buffered disk reads: 108 MB in 3.00 seconds = 35.95 MB/sec
Bonnie tests confirm this!
hdparm & bonnie & kern.log for comparison put at: http://dth.net/c3/
Anyone any idea *why* ?
Mayby i'm overlooking something (it's kind of late on this side of the pond) but still...
Open for feedback.
Danny
Signature · 4 lines
/"\ | Dying is to be avoided because \ / ASCII RIBBON CAMPAIGN | it can ruin your whole career X against HTML MAIL | / \ and POSTINGS | - Bob Hope
Quoted 7 lines · Danny ter Haar <[email protected]>, on Fri Feb 27, 2004 [12:04:29 AM]…
I've been checking, rechecking but cannot explain why a "vannilla" debian install kernel (sid-testing install cdrom) is faster then "Feisty Dunnart" on the same hardware.
hardware: Mini-itx with 1Ghz via-C3
200GB udma harddisk.
Quoted 9 lines
2.4.24:
Timing buffered disk reads: 150 MB in 3.01 seconds = 49.83 MB/sec2.6.3 (vanilla):
Timing buffered disk reads: 102 MB in 3.05 seconds = 33.40 MB/sec2.6.3-mm4:
Timing buffered disk reads: 108 MB in 3.00 seconds = 35.95 MB/sec
Hi; By default, my hdparm numbers and my kernel build time
benchmark were worse on all 2.6 vs. 2.4 kernels, until I tried:
/sbin/hdparm -a 4096 /dev/hdx
eg. (typical averages)
2.4.21:
Timing buffered disk reads: 80 MB in 3.07 seconds = 26.06 MB/sec
2.6.0-test5:
Timing buffered disk reads: 68 MB in 3.06 seconds = 22.21 MB/sec
2.6.1: [readahead 4096]
Timing buffered disk reads: 90 MB in 3.02 seconds = 29.82 MB/sec
2.6.0-test10 building 2.4.18-packet (personal config) gcc3.2.3 glibc2.3.2 160g Maxtor, ext3
(2xpII 400)
time (make -j4 clean && make -j4 dep && make -j4 bzImage) [with default read-ahead]
real 9m1.496s user 16m1.977s sys 0m45.347s
[read-ahead = 4096]
real 7m2.923s user 12m6.889s sys 0m46.190s
pIIx4, ata33, 160g maxtor
Quoted 10 lines · Paul
By default, my hdparm numbers and my kernel build time benchmark were worse on all 2.6 vs. 2.4 kernels, until I tried:
/sbin/hdparm-a 4096/dev/hdx
eg. (typical averages)
2.4.21:
Timing buffered disk reads: 80 MB in 3.07 seconds = 26.06 MB/sec
2.6.0-test5:
Timing buffered disk reads: 68 MB in 3.06 seconds = 22.21 MB/sec
2.6.1: [readahead 4096]
Timing buffered disk reads: 90 MB in 3.02 seconds = 29.82 MB/sec
Allready thought about that, tried that but no real
difference:belfish:~# uname -a Linux babelfish 2.6.3-mm4 #3 Fri Feb 27 14:09:38 CET 2004 i686 GNU/Linux
babelfish:~# /sbin/hdparm -a 4096 /dev/hda /dev/hda: setting fs readahead to 4096 readahead = 4096 (on)
babelfish:~# hdparm -t /dev/hda Timing buffered disk reads: 110 MB in 3.02 seconds = 36.47 MB/sec
I just installed a news amd64 en few 19" servers.
But none of them showed downgrade in performance when i upped the kernel.
Possibilities left (according to me!)
- scheduler (should i try different setup ?)
- irq problems (in combination with acpi?)
i booted with acpi=off and retested but same results.
- driver, specific the via-onboard.
No luck so far!
Danny
Signature · 4 lines
/"\ | Dying is to be avoided because \ / ASCII RIBBON CAMPAIGN | it can ruin your whole career X against HTML MAIL | / \ and POSTINGS | - Bob Hope