RTL network card problem
Hi,
When i just inserted this second network card my redhat network config shows this:
Desc. Type Device Status
RTL-8139/8139C/8139C+ Ethernet eth0 ok
RTL-8139/8139C/8139C+ Unknown dev22193 ok
Yes, i have two pci slots with two identical cards in. ifconfig shows this:
dev22193 Link encap:Ethernet HWaddr 00:E0:4C:39:32:3F
inet addr:192.168.0.5 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::2e0:4cff:fe39:323f/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:55 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:7474 (7.2 Kb)
Interrupt:10 Base address:0xc000eth0 Link encap:Ethernet HWaddr 00:10:A7:13:CB:0D
inet addr:192.168.1.101 Bcast:192.168.1.255
Mask:255.255.255.0
inet6 addr: fe80::210:a7ff:fe13:cb0d/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:108 errors:0 dropped:0 overruns:0 frame:0
TX packets:37 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:16616 (16.2 Kb) TX bytes:4623 (4.5 Kb)
Interrupt:11 Base address:0xc400So, my question is: why is this network card just partially found? my kudzu found it, i configured it, and it dont work...?
System: 700mhz celeron, 256mb ram, fedora core 2, and, as you see, one and a half network cards...
-
To unsubscribe from this list: send the line "unsubscribe linux-newbie" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.linux-learn.org/faqs
Quoted 32 lines · Ole Martin Handeland
Hi,
When i just inserted this second network card my redhat network config shows this:
Desc. Type Device Status
RTL-8139/8139C/8139C+ Ethernet eth0 ok
RTL-8139/8139C/8139C+ Unknown dev22193 okYes, i have two pci slots with two identical cards in. ifconfig shows this:
dev22193 Link encap:Ethernet HWaddr 00:E0:4C:39:32:3F
inet addr:192.168.0.5 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::2e0:4cff:fe39:323f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:55 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:7474 (7.2 Kb) Interrupt:10 Base address:0xc000eth0 Link encap:Ethernet HWaddr 00:10:A7:13:CB:0D
inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::210:a7ff:fe13:cb0d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:108 errors:0 dropped:0 overruns:0 frame:0 TX packets:37 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:16616 (16.2 Kb) TX bytes:4623 (4.5 Kb) Interrupt:11 Base address:0xc400
Quoted 3 lines
So, my question is: why is this network card just partially found? my kudzu found it, i configured it, and it dont work...?
System: 700mhz celeron, 256mb ram, fedora core 2, and, as you see, one and a half network cards...
They may not be identical.
What does 'cat /proc/pci' show, relative to the two cards? What is shown when the system is booted with one card at a time? HTH, Chuck
-
To unsubscribe from this list: send the line "unsubscribe linux-newbie" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.linux-learn.org/faqs
well, thanks to your questions, i figured it out myself, thanx!
if someone else want to know what i did:
i did a cat /proc/pci, found out this:
Bus 1, device 9, function 0:
Class 0200: PCI device 10ec:8139 (rev 16).
IRQ 10.
Master Capable. Latency=32. Min Gnt=32.Max Lat=64.
I/O at 0xc000 [0xc0ff].
Non-prefetchable 32 bit memory at 0xde000000 [0xde0000ff].
Bus 1, device 10, function 0:
Class 0200: PCI device 10ec:8139 (rev 16).
IRQ 11.
Master Capable. Latency=32. Min Gnt=32.Max Lat=64.
I/O at 0xc400 [0xc4ff].
Non-prefetchable 32 bit memory at 0xde001000 [0xde0010ff].i did a /sbin/lspci, and resulted in this:
01:09.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 01:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
i pulled out both cards, and, yes, they were almost identical (the exact same chipset, and therefore, the same driver.) i ran kudzu, removed the configurations for both cards.
shut down the box, and put the cards back in. power on.
kudzu now found both cards, and i configured, and now, both works! thanx!!
(wierd solution, but works...)
Quoted 45 lines · chuck gelm
Quoted 32 lines · Ole Martin Handeland
Hi,
When i just inserted this second network card my redhat network config shows this:
Desc. Type Device Status
RTL-8139/8139C/8139C+ Ethernet eth0 ok
RTL-8139/8139C/8139C+ Unknown dev22193 okYes, i have two pci slots with two identical cards in. ifconfig shows this:
dev22193 Link encap:Ethernet HWaddr 00:E0:4C:39:32:3F
inet addr:192.168.0.5 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::2e0:4cff:fe39:323f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:55 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:7474 (7.2 Kb) Interrupt:10 Base address:0xc000eth0 Link encap:Ethernet HWaddr 00:10:A7:13:CB:0D
inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::210:a7ff:fe13:cb0d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:108 errors:0 dropped:0 overruns:0 frame:0 TX packets:37 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:16616 (16.2 Kb) TX bytes:4623 (4.5 Kb) Interrupt:11 Base address:0xc400Quoted 3 lines
So, my question is: why is this network card just partially found? my kudzu found it, i configured it, and it dont work...?
System: 700mhz celeron, 256mb ram, fedora core 2, and, as you see, one and a half network cards...
They may not be identical.
What does 'cat/proc/pci' show, relative to the two cards? What is shown when the system is booted with one card at a time? HTH, Chuck
Quoted 6 lines
-
To unsubscribe from this list: send the line "unsubscribe linux-newbie" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.linux-learn.org/faqs
-
To unsubscribe from this list: send the line "unsubscribe linux-newbie" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.linux-learn.org/faqs