DMA timeout error
I have a VIA M6000 board with an ATA CompactFlash adaptor containing a 512MB SanDisk card.
I get the following error during boot:
hdb: dma_timer_expiry: dma status == 0x41
hdb: DMA timeout error
hdb: dma timeout error: status=0x58 { DriveReady SeekComplete DataRequest }
hdb: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hdb: drive not ready for command
hdb: dma_timer_expiry: dma status == 0x41
hdb: DMA timeout error
hdb: dma timeout error: status=0x58 { DriveReady SeekComplete DataRequest }
hdb: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hdb: drive not ready for command
Any ideas?
Thanks,
A.
Quoted 16 lines · Adam Sherman
I have a VIA M6000 board with an ATA CompactFlash adaptor containing a 512MB SanDisk card.
I get the following error during boot:
hdb:
dma_timer_expiry: dma status ==0x41
hdb: DMA timeout error
hdb: dma timeout error: status=0x58 { DriveReady SeekComplete DataRequest }hdb: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hdb: drive not ready for command
hdb:dma_timer_expiry: dma status ==0x41
hdb: DMA timeout error
hdb: dma timeout error: status=0x58 { DriveReady SeekComplete DataRequest }
Quoted 5 lines
hdb: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hdb: drive not ready for command
Any ideas?
If this is a new CF capable of DMA but CF-to-IDE adapter doesn't support DMA (most don't) then "ide=nodma" kernel command line parameter should do the job. It might be also bug in via82cxxx host driver.
Maybe DMA should be off by default for CF but it requires fixing almost every IDE host driver and why punish good hardware.
add pci=noapic to your boot option
;)
Quoted 34 lines · Adam Sherman
I have a VIA M6000 board with an ATA CompactFlash adaptor containing a 512MB SanDisk card.
I get the following error during boot:
hdb:
dma_timer_expiry: dma status ==0x41
hdb: DMA timeout error
hdb: dma timeout error: status=0x58 { DriveReady SeekComplete DataRequest }hdb: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hdb: drive not ready for command
hdb:dma_timer_expiry: dma status ==0x41
hdb: DMA timeout error
hdb: dma timeout error: status=0x58 { DriveReady SeekComplete DataRequest }hdb: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hdb: drive not ready for command
Any ideas?
Thanks,
A.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Signature · 5 lines
/* Beber : beber (AT) setibzh (DOT) com * https://guybrush.ath.cx * Using Mozilla Thunderbird on Gentoo Linux * Rachel @ friends.paris */
Quoted 10 lines · Bartlomiej Zolnierkiewicz
Quoted 8 lines
I have a VIA M6000 board with an ATA CompactFlash adaptor containing a 512MB SanDisk card.
I get the following error during boot:
hdb:
dma_timer_expiry: dma status ==0x41
hdb: DMA timeout error
hdb: dma timeout error: status=0x58 { DriveReady SeekComplete DataRequest }
Quoted 6 lines
If this is a new CF capable of DMA but CF-to-IDE adapter doesn't support DMA (most don't) then "ide=nodma" kernel command line parameter should do the job. It might be also bug in via82cxxx host driver.
Maybe DMA should be off by default for CF but it requires fixing almost every IDE host driver and why punish good hardware.
This makes quite a bit of sense seeing as it's a SanDisk "Ultra II" card.
Quoted 1 line · [email protected] writes:
add pci=noapic to your boot option
Since the hardware is not reachable from here, I can not test it until Monday. I'll note my results though.
Thanks,
A.