linux patches of loongson-based machines
Subsystems (8)
cover linux patches of loongson-based machines
From: Wu Zhangjin <[email protected]>
Dear all,
I have cleaned up the source code of loongson-based machines support and updated it to linux-2.6.29.3, the latest result is put to the following git repository:
git://dev.lemote.com/rt4ls.git to-ralf
or
http://dev.lemote.com/cgit/rt4ls.git/log/?h=to-ralf
this job is based on the to-mips branch of Yanhua'sgit://dev.lemote.com/linux_loongson.git and the lm2e-fixes branch of Philippe'sgit://git.linux-cisco.org/linux-mips.git. thanks goes to them.
and also, thanks goes to Erwen and heihaier for testing the latest branch, and thanks ralf, zhangLe, john and the other guyes for reviewing the old branch and giving good suggestions.
the most differences between this branch and the old branch include:
* all of these patches are checked by script/checkpatch.pl, only a few warnings left.
* the cs5536 part have been cleaned up deeply. the old pcireg.h is removed via using the include/linux/pci_regs.h instead. and the old cs5536_vsm.c is divided to several modules, one file one module.
* the source code in driver/video/smi in cleaned up a lot, two trashy header files are removed, and several trashy functions are removed, lots of coding style errors and warnings are cleaned up.
* gcc 4.4 support, including 32bit and 64bit, and also it is gcc 4.3 compatiable
I have tested it in 32bit and 64bit with gcc 4.3 on fuloong(2e), fuloong(2f), yeeloong(2f), all of them work well, and also test it in 32bit and 64bit with gcc 4.4 on fuloong(2f), works normally. Erwen and heihaier have tested it in 64bit with gcc 4.4 on a yeeloong laptop.
* the current source code architecture
$ tree arch/mips/loongson/
arch/mips/loongson/
|-- Kconfig
|-- Makefile
|-- common
| |-- Makefile
| |-- bonito-irq.c
| |-- clock.c
| |-- cmdline.c
| |-- cs5536
| | |-- Makefile
| | |-- cs5536_acc.c
| | |-- cs5536_ehci.c
| | |-- cs5536_flash.c
| | |-- cs5536_ide.c
| | |-- cs5536_isa.c
| | |-- cs5536_mfgpt.c --> cs5536 mfgpt timer
| | |-- cs5536_ohci.c
| | |-- cs5536_otg.c
| | |-- cs5536_pci.c --> cs5536_pci_conf_read4/write4
| | `-- cs5536_udc.c
| |-- early_printk.c
| |-- init.c
| |-- irq.c
| |-- mem.c
| |-- misc.c
| |-- pci.c
| |-- reset.c
| |-- rtc.c
| |-- serial.c
| |-- setup.c
| `-- time.c
|-- fuloong-2e
| |-- Makefile
| |-- irq.c
| `-- reset.c
|-- fuloong-2f
| |-- Makefile
| |-- irq.c
| `-- reset.c
`-- yeeloong-2f
|-- Makefile
|-- init.c
|-- irq.c
`-- reset.c$ tree arch/mips/include/asm/mach-loongson/ arch/mips/include/asm/mach-loongson/ |-- cmdline.h |-- cpu-feature-overrides.h |-- cs5536 | |-- cs5536.h | |-- cs5536_mfgpt.h | |-- cs5536_pci.h | `-- cs5536_vsm.h |-- dma-coherence.h |-- loongson.h |-- machine.h --> merged from the old board-name/machine.h |-- mc146818rtc.h |-- mem.h |-- pci.h `-- war.h
* PCI relative files:
arch/mips/pci/fixup-fuloong2e.c arch/mips/pci/fixup-lemote2f.carch/mips/pci/ops-loongson2.c ^^^^^^^^|
|^^^^^^^ fuloong2f & yeeloong2f
have preserved a position for gdium
* Video card Driver(SMI) for yeeloong2f
$ drivers/video/smi/ |-- Makefile |-- smtc2d.c |-- smtc2d.h |-- smtcfb.c `-- smtcfb.h
* STD support for MIPS
$ arch/mips/power/ |-- Makefile |-- cpu.c `-- hibernate.S
* Oprofile support for loongson2
arch/mips/oprofile/op_model_loongson2.c
* cpufrq support for loongson2f
arch/mips/kerenl/loongson2f_freq.carch/mips/loongson/common/clock.c
* gcc 4.4 support for MIPS
arch/mips/include/asm/compiler.harch/mips/include/asm/delay.harch/mips/include/asm/div64.h
* gcc 4.4 support for loongson2e/2f
arch/mips/Makefile
Wu Zhangjin (27):
fix-warning: incompatible argument type of pci_fixup_irqs
fix-warning: incompatible argument type of virt_to_phys
fix-error: incompatiable argument type of clear_user change the naming methods
remove reference to bonito64.h
divide the files to the smallest logic unit replace tons of magic numbers by understandable symbols clean up the early printk support for fuloong(2e) enable Real Time Clock Support for fuloong(2e) add loongson-specific cpu-feature-overrides.h split the loongson-specific part out
add basic loongson-2f support
add basic fuloong(2f) support
enable serial port support of loongson-based machines add basic yeeloong(2f) laptop support
Add Siliconmotion 712 framebuffer driver
define Loongson2F arch specific phys prot access Loongson2 specific OProfile driver
flush posted write to irq
CS5536 MFGPT as system clock source support Loongson2F cpufreq support
Hibernation Support in mips system
Alsa memory maps fixup on mips systems
fixup for FUJITSU disk
Flush RAS and BTB for CPU predictively execution add default kernel config file for loongson-based machines add gcc 4.4 support for MIPS and loongson
.gitignore | 1 + arch/mips/Kconfig | 92 +- arch/mips/Makefile | 21 +- arch/mips/configs/fulong_defconfig | 1912 -------------- arch/mips/configs/fuloong2e_defconfig | 1977 +++++++++++++++ arch/mips/configs/fuloong2f_defconfig | 2630 +++++++++++++++++++ arch/mips/configs/yeeloong2f_defconfig | 2641 ++++++++++++++++++++ arch/mips/include/asm/clock.h | 64 + arch/mips/include/asm/compiler.h | 10 + arch/mips/include/asm/delay.h | 58 +- arch/mips/include/asm/div64.h | 24 +- arch/mips/include/asm/mach-lemote/dma-coherence.h | 66 - arch/mips/include/asm/mach-lemote/mc146818rtc.h | 36 - arch/mips/include/asm/mach-lemote/pci.h | 30 - arch/mips/include/asm/mach-lemote/war.h | 25 - arch/mips/include/asm/mach-loongson/cmdline.h | 9 + .../asm/mach-loongson/cpu-feature-overrides.h | 58 + .../mips/include/asm/mach-loongson/cs5536/cs5536.h | 382 +++ .../asm/mach-loongson/cs5536/cs5536_mfgpt.h | 26 + .../include/asm/mach-loongson/cs5536/cs5536_pci.h | 174 ++ .../include/asm/mach-loongson/cs5536/cs5536_vsm.h | 59 + .../mips/include/asm/mach-loongson/dma-coherence.h | 70 + arch/mips/include/asm/mach-loongson/loongson.h | 311 +++ arch/mips/include/asm/mach-loongson/machine.h | 87 + arch/mips/include/asm/mach-loongson/mc146818rtc.h | 36 + arch/mips/include/asm/mach-loongson/mem.h | 31 + arch/mips/include/asm/mach-loongson/pci.h | 59 + arch/mips/include/asm/mach-loongson/war.h | 25 + arch/mips/include/asm/mips-boards/bonito64.h | 5 - arch/mips/include/asm/page.h | 5 +- arch/mips/include/asm/pci.h | 2 +- arch/mips/include/asm/pgtable.h | 13 + arch/mips/include/asm/stackframe.h | 14 + arch/mips/include/asm/suspend.h | 2 + arch/mips/include/asm/uaccess.h | 2 +- arch/mips/kernel/Makefile | 1 + arch/mips/kernel/asm-offsets.c | 13 + arch/mips/kernel/i8259.c | 2 + arch/mips/kernel/loongson2f_freq.c | 223 ++ arch/mips/lemote/lm2e/Makefile | 7 - arch/mips/lemote/lm2e/bonito-irq.c | 74 - arch/mips/lemote/lm2e/dbg_io.c | 146 -- arch/mips/lemote/lm2e/irq.c | 144 -- arch/mips/lemote/lm2e/mem.c | 23 - arch/mips/lemote/lm2e/pci.c | 97 - arch/mips/lemote/lm2e/prom.c | 97 - arch/mips/lemote/lm2e/reset.c | 41 - arch/mips/lemote/lm2e/setup.c | 111 - arch/mips/loongson/Kconfig | 135 + arch/mips/loongson/Makefile | 23 + arch/mips/loongson/common/Makefile | 37 + arch/mips/loongson/common/bonito-irq.c | 78 + arch/mips/loongson/common/clock.c | 166 ++ arch/mips/loongson/common/cmdline.c | 85 + arch/mips/loongson/common/cs5536/Makefile | 25 + arch/mips/loongson/common/cs5536/cs5536_acc.c | 155 ++ arch/mips/loongson/common/cs5536/cs5536_ehci.c | 165 ++ arch/mips/loongson/common/cs5536/cs5536_flash.c | 450 ++++ arch/mips/loongson/common/cs5536/cs5536_ide.c | 193 ++ arch/mips/loongson/common/cs5536/cs5536_isa.c | 376 +++ arch/mips/loongson/common/cs5536/cs5536_mfgpt.c | 258 ++ arch/mips/loongson/common/cs5536/cs5536_ohci.c | 167 ++ arch/mips/loongson/common/cs5536/cs5536_otg.c | 137 + arch/mips/loongson/common/cs5536/cs5536_pci.c | 126 + arch/mips/loongson/common/cs5536/cs5536_udc.c | 142 ++ arch/mips/loongson/common/early_printk.c | 28 + arch/mips/loongson/common/init.c | 57 + arch/mips/loongson/common/irq.c | 134 + arch/mips/loongson/common/mem.c | 116 + arch/mips/loongson/common/misc.c | 15 + arch/mips/loongson/common/pci.c | 109 + arch/mips/loongson/common/reset.c | 38 + arch/mips/loongson/common/rtc.c | 54 + arch/mips/loongson/common/serial.c | 64 + arch/mips/loongson/common/setup.c | 74 + arch/mips/loongson/common/time.c | 34 + arch/mips/loongson/fuloong-2e/Makefile | 7 + arch/mips/loongson/fuloong-2e/irq.c | 58 + arch/mips/loongson/fuloong-2e/reset.c | 26 + arch/mips/loongson/fuloong-2f/Makefile | 5 + arch/mips/loongson/fuloong-2f/irq.c | 53 + arch/mips/loongson/fuloong-2f/reset.c | 65 + arch/mips/loongson/yeeloong-2f/Makefile | 5 + arch/mips/loongson/yeeloong-2f/init.c | 71 + arch/mips/loongson/yeeloong-2f/irq.c | 53 + arch/mips/loongson/yeeloong-2f/reset.c | 40 + arch/mips/oprofile/Makefile | 1 + arch/mips/oprofile/common.c | 5 + arch/mips/oprofile/op_model_loongson2.c | 186 ++ arch/mips/pci/Makefile | 4 +- arch/mips/pci/fixup-au1000.c | 2 +- arch/mips/pci/fixup-capcella.c | 2 +- arch/mips/pci/fixup-cobalt.c | 2 +- arch/mips/pci/fixup-emma2rh.c | 2 +- arch/mips/pci/fixup-excite.c | 2 +- arch/mips/pci/fixup-fuloong2e.c | 243 ++ arch/mips/pci/fixup-ip32.c | 2 +- arch/mips/pci/fixup-lemote2f.c | 171 ++ arch/mips/pci/fixup-lm2e.c | 242 -- arch/mips/pci/fixup-malta.c | 2 +- arch/mips/pci/fixup-mpc30x.c | 2 +- arch/mips/pci/fixup-pmcmsp.c | 2 +- arch/mips/pci/fixup-pnx8550.c | 2 +- arch/mips/pci/fixup-rc32434.c | 2 +- arch/mips/pci/fixup-sni.c | 2 +- arch/mips/pci/fixup-tb0219.c | 2 +- arch/mips/pci/fixup-tb0226.c | 2 +- arch/mips/pci/fixup-tb0287.c | 2 +- arch/mips/pci/fixup-wrppmc.c | 2 +- arch/mips/pci/fixup-yosemite.c | 2 +- arch/mips/pci/ops-bonito64.c | 19 +- arch/mips/pci/ops-loongson2.c | 213 ++ arch/mips/pci/pci-bcm1480.c | 2 +- arch/mips/pci/pci-bcm47xx.c | 2 +- arch/mips/pci/pci-ip27.c | 2 +- arch/mips/pci/pci-lasat.c | 2 +- arch/mips/pci/pci-sb1250.c | 2 +- arch/mips/power/Makefile | 1 + arch/mips/power/cpu.c | 51 + arch/mips/power/hibernate.S | 78 + arch/mips/txx9/generic/pci.c | 2 +- drivers/ide/amd74xx.c | 19 + drivers/rtc/rtc-cmos.c | 8 +- drivers/video/Kconfig | 23 + drivers/video/Makefile | 1 + drivers/video/smi/Makefile | 8 + drivers/video/smi/smtc2d.c | 979 ++++++++ drivers/video/smi/smtc2d.h | 530 ++++ drivers/video/smi/smtcfb.c | 1141 +++++++++ drivers/video/smi/smtcfb.h | 793 ++++++ include/linux/suspend.h | 3 +- sound/core/pcm_native.c | 9 + sound/core/sgbuf.c | 9 + sound/pci/Kconfig | 1 - 134 files changed, 17383 insertions(+), 3161 deletions(-) delete mode 100644 arch/mips/configs/fulong_defconfig create mode 100644 arch/mips/configs/fuloong2e_defconfig create mode 100644 arch/mips/configs/fuloong2f_defconfig create mode 100644 arch/mips/configs/yeeloong2f_defconfig create mode 100644 arch/mips/include/asm/clock.h delete mode 100644 arch/mips/include/asm/mach-lemote/dma-coherence.h delete mode 100644 arch/mips/include/asm/mach-lemote/mc146818rtc.h delete mode 100644 arch/mips/include/asm/mach-lemote/pci.h delete mode 100644 arch/mips/include/asm/mach-lemote/war.h create mode 100644 arch/mips/include/asm/mach-loongson/cmdline.h create mode 100644 arch/mips/include/asm/mach-loongson/cpu-feature-overrides.h create mode 100644 arch/mips/include/asm/mach-loongson/cs5536/cs5536.h create mode 100644 arch/mips/include/asm/mach-loongson/cs5536/cs5536_mfgpt.h create mode 100644 arch/mips/include/asm/mach-loongson/cs5536/cs5536_pci.h create mode 100644 arch/mips/include/asm/mach-loongson/cs5536/cs5536_vsm.h create mode 100644 arch/mips/include/asm/mach-loongson/dma-coherence.h create mode 100644 arch/mips/include/asm/mach-loongson/loongson.h create mode 100644 arch/mips/include/asm/mach-loongson/machine.h create mode 100644 arch/mips/include/asm/mach-loongson/mc146818rtc.h create mode 100644 arch/mips/include/asm/mach-loongson/mem.h create mode 100644 arch/mips/include/asm/mach-loongson/pci.h create mode 100644 arch/mips/include/asm/mach-loongson/war.h create mode 100644 arch/mips/kernel/loongson2f_freq.c delete mode 100644 arch/mips/lemote/lm2e/Makefile delete mode 100644 arch/mips/lemote/lm2e/bonito-irq.c delete mode 100644 arch/mips/lemote/lm2e/dbg_io.c delete mode 100644 arch/mips/lemote/lm2e/irq.c delete mode 100644 arch/mips/lemote/lm2e/mem.c delete mode 100644 arch/mips/lemote/lm2e/pci.c delete mode 100644 arch/mips/lemote/lm2e/prom.c delete mode 100644 arch/mips/lemote/lm2e/reset.c delete mode 100644 arch/mips/lemote/lm2e/setup.c create mode 100644 arch/mips/loongson/Kconfig create mode 100644 arch/mips/loongson/Makefile create mode 100644 arch/mips/loongson/common/Makefile create mode 100644 arch/mips/loongson/common/bonito-irq.c create mode 100644 arch/mips/loongson/common/clock.c create mode 100644 arch/mips/loongson/common/cmdline.c create mode 100644 arch/mips/loongson/common/cs5536/Makefile create mode 100644 arch/mips/loongson/common/cs5536/cs5536_acc.c create mode 100644 arch/mips/loongson/common/cs5536/cs5536_ehci.c create mode 100644 arch/mips/loongson/common/cs5536/cs5536_flash.c create mode 100644 arch/mips/loongson/common/cs5536/cs5536_ide.c create mode 100644 arch/mips/loongson/common/cs5536/cs5536_isa.c create mode 100644 arch/mips/loongson/common/cs5536/cs5536_mfgpt.c create mode 100644 arch/mips/loongson/common/cs5536/cs5536_ohci.c create mode 100644 arch/mips/loongson/common/cs5536/cs5536_otg.c create mode 100644 arch/mips/loongson/common/cs5536/cs5536_pci.c create mode 100644 arch/mips/loongson/common/cs5536/cs5536_udc.c create mode 100644 arch/mips/loongson/common/early_printk.c create mode 100644 arch/mips/loongson/common/init.c create mode 100644 arch/mips/loongson/common/irq.c create mode 100644 arch/mips/loongson/common/mem.c create mode 100644 arch/mips/loongson/common/misc.c create mode 100644 arch/mips/loongson/common/pci.c create mode 100644 arch/mips/loongson/common/reset.c create mode 100644 arch/mips/loongson/common/rtc.c create mode 100644 arch/mips/loongson/common/serial.c create mode 100644 arch/mips/loongson/common/setup.c create mode 100644 arch/mips/loongson/common/time.c create mode 100644 arch/mips/loongson/fuloong-2e/Makefile create mode 100644 arch/mips/loongson/fuloong-2e/irq.c create mode 100644 arch/mips/loongson/fuloong-2e/reset.c create mode 100644 arch/mips/loongson/fuloong-2f/Makefile create mode 100644 arch/mips/loongson/fuloong-2f/irq.c create mode 100644 arch/mips/loongson/fuloong-2f/reset.c create mode 100644 arch/mips/loongson/yeeloong-2f/Makefile create mode 100644 arch/mips/loongson/yeeloong-2f/init.c create mode 100644 arch/mips/loongson/yeeloong-2f/irq.c create mode 100644 arch/mips/loongson/yeeloong-2f/reset.c create mode 100644 arch/mips/oprofile/op_model_loongson2.c create mode 100644 arch/mips/pci/fixup-fuloong2e.c create mode 100644 arch/mips/pci/fixup-lemote2f.c delete mode 100644 arch/mips/pci/fixup-lm2e.c create mode 100644 arch/mips/pci/ops-loongson2.c create mode 100644 arch/mips/power/Makefile create mode 100644 arch/mips/power/cpu.c create mode 100644 arch/mips/power/hibernate.S create mode 100644 drivers/video/smi/Makefile create mode 100644 drivers/video/smi/smtc2d.c create mode 100644 drivers/video/smi/smtc2d.h create mode 100644 drivers/video/smi/smtcfb.c create mode 100644 drivers/video/smi/smtcfb.h
PATCH 1/27 fix-warning: incompatible argument type of pci_fixup_irqs
From: Wu Zhangjin <[email protected]>
arch/mips/pci/pci.c:160: warning: passing argument 2 of ‘pci_fixup_irqs’ from incompatible pointer type
include/linux/pci.h:
void pci_fixup_irqs(u8 (*)(struct pci_dev *, u8 *),
int (*)(struct pci_dev *, u8, u8));arch/mips/pci/pci.c:160:
pci_fixup_irqs(pci_common_swizzle, pcibios_map_irq);
arch/mips/include/asm/pci.h:
extern int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin);
arch/mips/pci/fixup-malta.c
int __init pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
--- arch/mips/include/asm/pci.h | 2 +- arch/mips/pci/fixup-au1000.c | 2 +- arch/mips/pci/fixup-capcella.c | 2 +- arch/mips/pci/fixup-cobalt.c | 2 +- arch/mips/pci/fixup-emma2rh.c | 2 +- arch/mips/pci/fixup-excite.c | 2 +- arch/mips/pci/fixup-ip32.c | 2 +- arch/mips/pci/fixup-lm2e.c | 2 +- arch/mips/pci/fixup-malta.c | 2 +- arch/mips/pci/fixup-mpc30x.c | 2 +- arch/mips/pci/fixup-pmcmsp.c | 2 +- arch/mips/pci/fixup-pnx8550.c | 2 +- arch/mips/pci/fixup-rc32434.c | 2 +- arch/mips/pci/fixup-sni.c | 2 +- arch/mips/pci/fixup-tb0219.c | 2 +- arch/mips/pci/fixup-tb0226.c | 2 +- arch/mips/pci/fixup-tb0287.c | 2 +- arch/mips/pci/fixup-wrppmc.c | 2 +- arch/mips/pci/fixup-yosemite.c | 2 +- arch/mips/pci/pci-bcm1480.c | 2 +- arch/mips/pci/pci-bcm47xx.c | 2 +- arch/mips/pci/pci-ip27.c | 2 +- arch/mips/pci/pci-lasat.c | 2 +- arch/mips/pci/pci-sb1250.c | 2 +- arch/mips/txx9/generic/pci.c | 2 +- 25 files changed, 25 insertions(+), 25 deletions(-)
arch/mips/include/asm/pci.h +1 -1
@@ -56,7 +56,7 @@ extern void register_pci_controller(struct pci_controller *hose);/* * board supplied pci irq fixup routine */ -extern int pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin); +extern int pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin);/* Can be used to override the logic in pci_scan_bus for skipping
arch/mips/pci/fixup-au1000.c +1 -1
@@ -31,7 +31,7 @@extern char irq_tab_alchemy[][5 ]; -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return irq_tab_alchemy[slot][pin]; }
arch/mips/pci/fixup-capcella.c +1 -1
@@ -38,7 +38,7 @@ static char irq_tab_capcella[][5] __initdata = { [14] = { -1, INTA, INTB, INTC, INTD } }; -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return irq_tab_capcella[slot][pin]; }
arch/mips/pci/fixup-cobalt.c +1 -1
@@ -175,7 +175,7 @@ static char irq_tab_raq2[] __initdata = { [COBALT_PCICONF_ETH1] = ETH1_IRQ }; -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {if (cobalt_board_id <=COBALT_BRD_ID_QUBE1 )return irq_tab_qube1[slot];
arch/mips/pci/fixup-emma2rh.c +1 -1
@@ -88,7 +88,7 @@ static void __devinit emma2rh_pci_host_fixup(struct pci_dev *dev)DECLARE_PCI_FIXUP_HEADER (PCI_VENDOR_ID_NEC ,PCI_DEVICE_ID_NEC_EMMA2RH , emma2rh_pci_host_fixup); -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return irq_map[slot][pin]; }
arch/mips/pci/fixup-excite.c +1 -1
@@ -21,7 +21,7 @@#include <linux/pci.h> #include <excite.h> -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {if (pin ==0 )return -1 ;
arch/mips/pci/fixup-ip32.c +1 -1
@@ -39,7 +39,7 @@ static char irq_tab_mace[][5] __initdata = {* irqs. I suppose a device without a pin A will thank us for doing it * right if there exists such a broken piece of crap. */ -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return irq_tab_mace[slot][pin]; }
arch/mips/pci/fixup-lm2e.c +1 -1
@@ -36,7 +36,7 @@/* South bridge slot number is set by the pci probe process */ static u8 sb_slot =5 ; -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {int irq =0 ;
arch/mips/pci/fixup-malta.c +1 -1
@@ -36,7 +36,7 @@ static char irq_tab[][5] __initdata = { {0, PCID, PCIA, PCIB, PCIC } /* 21: PCI Slot 4 */ }; -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {int virq; virq = irq_tab[slot][pin];
arch/mips/pci/fixup-mpc30x.c +1 -1
@@ -34,7 +34,7 @@ static const int irq_tab_mpc30x[] __initdata = { [29] = MQ200_IRQ, }; -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {if (slot ==30 )return internal_func_irqs[PCI_FUNC (dev->devfn)];
arch/mips/pci/fixup-pmcmsp.c +1 -1
@@ -202,7 +202,7 @@ int pcibios_plat_dev_init(struct pci_dev *dev)* RETURNS: IRQ number * ****************************************************************************/ -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {#if !defined(CONFIG_PMC_MSP7120_GW ) && !defined(CONFIG_PMC_MSP7120_EVAL )printk (KERN_WARNING "PCI: unknown board, no PCI IRQs assigned.\n" );
arch/mips/pci/fixup-pnx8550.c +1 -1
@@ -45,7 +45,7 @@ void __init pcibios_fixup(void)/* nothing to do here */ } -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return pnx8550_irq_tab[slot][pin]; }
arch/mips/pci/fixup-rc32434.c +1 -1
@@ -37,7 +37,7 @@ static int __devinitdata irq_map[2][12] = { {0, 0, 1, 3, 0, 2, 1, 3, 0, 2, 1, 3} }; -int __devinit pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __devinit pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {int irq =0 ;
arch/mips/pci/fixup-sni.c +1 -1
@@ -130,7 +130,7 @@ static inline int is_rm300_revd(void)return (csmsr &0xa0 ) ==0x20 ; } -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {switch (sni_brd_type) {case SNI_BRD_PCI_TOWER_CPLUS :
arch/mips/pci/fixup-tb0219.c +1 -1
@@ -23,7 +23,7 @@#include <asm/vr41xx/tb0219.h> -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {int irq =-1 ;
arch/mips/pci/fixup-tb0226.c +1 -1
@@ -23,7 +23,7 @@#include <asm/vr41xx/giu.h> #include <asm/vr41xx/tb0226.h> -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {int irq =-1 ;
arch/mips/pci/fixup-tb0287.c +1 -1
@@ -22,7 +22,7 @@#include <asm/vr41xx/tb0287.h> -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {unsigned char bus;int irq =-1 ;
arch/mips/pci/fixup-wrppmc.c +1 -1
@@ -25,7 +25,7 @@ static char pci_irq_tab[PCI_SLOT_MAXNR][5] __initdata = { [6] = {0, WRPPMC_PCI_INTA_IRQ, 0, 0, 0}, }; -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return pci_irq_tab[slot][pin]; }
arch/mips/pci/fixup-yosemite.c +1 -1
@@ -26,7 +26,7 @@#include <linux/init.h> #include <linux/pci.h> -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {if (pin ==0 )return -1 ;
arch/mips/pci/pci-bcm1480.c +1 -1
@@ -74,7 +74,7 @@ static inline void WRITECFG32(u32 addr, u32 data) *(u32 *)(cfg_space + (addr & ~3 )) = data; } -int pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {if (pin ==0 )return -1 ;
arch/mips/pci/pci-bcm47xx.c +1 -1
@@ -26,7 +26,7 @@#include <linux/pci.h> #include <linux/ssb/ssb.h> -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return 0 ; }
arch/mips/pci/pci-ip27.c +1 -1
@@ -141,7 +141,7 @@ int __cpuinit bridge_probe(nasid_t nasid, int widget_id, int masterwid)* A given PCI device, in general, should be able to intr any of the cpus * on any one of the hubs connected to its xbow. */ -int __devinit pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __devinit pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return 0 ; }
arch/mips/pci/pci-lasat.c +1 -1
@@ -61,7 +61,7 @@ arch_initcall(lasat_pci_setup);#define LASAT_IRQ_PCIC (LASAT_IRQ_BASE + 7)#define LASAT_IRQ_PCID (LASAT_IRQ_BASE + 8) -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {switch (slot) {case 1 :
arch/mips/pci/pci-sb1250.c +1 -1
@@ -84,7 +84,7 @@ static inline void WRITECFG32(u32 addr, u32 data) *(u32 *) (cfg_space + (addr & ~3 )) = data; } -int pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return dev->irq; }
arch/mips/txx9/generic/pci.c +1 -1
@@ -382,7 +382,7 @@ int pcibios_plat_dev_init(struct pci_dev *dev)return 0 ; } -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return txx9_board_vec->pci_map_irq (dev, slot, pin); }
Signature · 1 line
1.6.2.1
PATCH 2/27 fix-warning: incompatible argument type of virt_to_phys
In reply to [email protected]From: Wu Zhangjin <[email protected]>
mm/page_alloc.c:1760: warning: passing argument 1 of ‘virt_to_phys’ makes pointer from integer without a cast
mm/page_alloc.c:1760
... unsigned long addr; ... split_page(virt_to_page(addr), order);
arch/mips/include/asm/page.h
#define virt_to_page(kaddr) pfn_to_page(PFN_DOWN(virt_to_phys(kaddr))) #define virt_addr_valid(kaddr) pfn_valid(PFN_DOWN(virt_to_phys(kaddr)))
arch/mips/include/asm/io.h
static inline unsigned long virt_to_phys(volatile const void *address)
--- arch/mips/include/asm/page.h | 5 +++-- 1 files changed, 3 insertions(+), 2 deletions(-)
arch/mips/include/asm/page.h +3 -2
@@ -176,8 +176,9 @@ typedef struct { unsigned long pgprot; } pgprot_t;#endif -#define virt_to_page (kaddr) pfn_to_page(PFN_DOWN(virt_to_phys(kaddr))) -#define virt_addr_valid (kaddr) pfn_valid(PFN_DOWN(virt_to_phys(kaddr))) +#define virt_to_page (kaddr) \ + pfn_to_page(PFN_DOWN(virt_to_phys((void *)kaddr))) +#define virt_addr_valid (kaddr) pfn_valid(PFN_DOWN(virt_to_phys((void *)kaddr)))#define VM_DATA_DEFAULT_FLAGS (VM_READ | VM_WRITE | VM_EXEC | \ VM_MAYREAD | VM_MAYWRITE | VM_MAYEXEC)
Signature · 1 line
1.6.2.1
PATCH 3/27 fix-error: incompatiable argument type of clear_user
In reply to [email protected]From: Wu Zhangjin <[email protected]>
there are lots of warnings about the macro: clear_user in linux-mips.
the type of the second argument of access_ok should be (void __user *), but there is an un-needed (unsigned long) conversion before __cl_addr, so, remove the (unsigned long) will fix this problem.
--- arch/mips/include/asm/uaccess.h | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-)
arch/mips/include/asm/uaccess.h +1 -1
@@ -936,7 +936,7 @@ __clear_user(void __user *addr, __kernel_size_t size) void __user * __cl_addr = (addr); \unsigned long __cl_size = (n); \if (__cl_size &&access_ok (VERIFY_WRITE , \ - ((unsigned long )(__cl_addr)), __cl_size)) \ + __cl_addr, __cl_size)) \ __cl_size =__clear_user (__cl_addr, __cl_size); \ __cl_size; \ })
Signature · 1 line
1.6.2.1
PATCH 4/27 change the naming methods
In reply to [email protected]From: Wu Zhangjin <[email protected]>
to support loongson-based machines made by non-lemote companies, some lemote* names should be changed to loongson* names, and to support the future loongson2f-based fulong machines, the current fulong's name should be fuloong-2e or fuloong2e, and also, FULONG to FULOONG2E, lm2e to fuloong2e, LEMOTE to LOONGSON.
at the same time, tons of lines have been cleaned up with the help of scripts/checkpatch.pl
--- .gitignore | 1 + arch/mips/Kconfig | 4 +- arch/mips/Makefile | 6 +- arch/mips/include/asm/mach-lemote/dma-coherence.h | 66 ------ arch/mips/include/asm/mach-lemote/mc146818rtc.h | 36 --- arch/mips/include/asm/mach-lemote/pci.h | 30 --- arch/mips/include/asm/mach-lemote/war.h | 25 -- .../mips/include/asm/mach-loongson/dma-coherence.h | 66 ++++++ arch/mips/include/asm/mach-loongson/loongson.h | 14 ++ arch/mips/include/asm/mach-loongson/mc146818rtc.h | 36 +++ arch/mips/include/asm/mach-loongson/pci.h | 32 +++ arch/mips/include/asm/mach-loongson/war.h | 25 ++ arch/mips/include/asm/mips-boards/bonito64.h | 2 +- arch/mips/lemote/lm2e/Makefile | 7 - arch/mips/lemote/lm2e/bonito-irq.c | 74 ------ arch/mips/lemote/lm2e/dbg_io.c | 146 ------------ arch/mips/lemote/lm2e/irq.c | 144 ------------ arch/mips/lemote/lm2e/mem.c | 23 -- arch/mips/lemote/lm2e/pci.c | 97 -------- arch/mips/lemote/lm2e/prom.c | 97 -------- arch/mips/lemote/lm2e/reset.c | 41 ---- arch/mips/lemote/lm2e/setup.c | 111 --------- arch/mips/loongson/fuloong-2e/Makefile | 7 + arch/mips/loongson/fuloong-2e/bonito-irq.c | 73 ++++++ arch/mips/loongson/fuloong-2e/dbg_io.c | 153 ++++++++++++ arch/mips/loongson/fuloong-2e/irq.c | 140 +++++++++++ arch/mips/loongson/fuloong-2e/mem.c | 23 ++ arch/mips/loongson/fuloong-2e/pci.c | 95 ++++++++ arch/mips/loongson/fuloong-2e/prom.c | 90 ++++++++ arch/mips/loongson/fuloong-2e/reset.c | 37 +++ arch/mips/loongson/fuloong-2e/setup.c | 108 +++++++++ arch/mips/pci/Makefile | 2 +- arch/mips/pci/fixup-fuloong2e.c | 242 ++++++++++++++++++++ arch/mips/pci/fixup-lm2e.c | 242 -------------------- arch/mips/pci/ops-bonito64.c | 16 +- 35 files changed, 1158 insertions(+), 1153 deletions(-) delete mode 100644 arch/mips/include/asm/mach-lemote/dma-coherence.h delete mode 100644 arch/mips/include/asm/mach-lemote/mc146818rtc.h delete mode 100644 arch/mips/include/asm/mach-lemote/pci.h delete mode 100644 arch/mips/include/asm/mach-lemote/war.h create mode 100644 arch/mips/include/asm/mach-loongson/dma-coherence.h create mode 100644 arch/mips/include/asm/mach-loongson/loongson.h create mode 100644 arch/mips/include/asm/mach-loongson/mc146818rtc.h create mode 100644 arch/mips/include/asm/mach-loongson/pci.h create mode 100644 arch/mips/include/asm/mach-loongson/war.h delete mode 100644 arch/mips/lemote/lm2e/Makefile delete mode 100644 arch/mips/lemote/lm2e/bonito-irq.c delete mode 100644 arch/mips/lemote/lm2e/dbg_io.c delete mode 100644 arch/mips/lemote/lm2e/irq.c delete mode 100644 arch/mips/lemote/lm2e/mem.c delete mode 100644 arch/mips/lemote/lm2e/pci.c delete mode 100644 arch/mips/lemote/lm2e/prom.c delete mode 100644 arch/mips/lemote/lm2e/reset.c delete mode 100644 arch/mips/lemote/lm2e/setup.c create mode 100644 arch/mips/loongson/fuloong-2e/Makefile create mode 100644 arch/mips/loongson/fuloong-2e/bonito-irq.c create mode 100644 arch/mips/loongson/fuloong-2e/dbg_io.c create mode 100644 arch/mips/loongson/fuloong-2e/irq.c create mode 100644 arch/mips/loongson/fuloong-2e/mem.c create mode 100644 arch/mips/loongson/fuloong-2e/pci.c create mode 100644 arch/mips/loongson/fuloong-2e/prom.c create mode 100644 arch/mips/loongson/fuloong-2e/reset.c create mode 100644 arch/mips/loongson/fuloong-2e/setup.c create mode 100644 arch/mips/pci/fixup-fuloong2e.c delete mode 100644 arch/mips/pci/fixup-lm2e.c
.gitignore +1 -0
@@ -32,6 +32,7 @@ tags TAGS vmlinux +vmlinux.32 System.map Module.markers Module.symvers
arch/mips/Kconfig +2 -2
@@ -156,8 +156,8 @@ config LASAT select SYS_SUPPORTS_LITTLE_ENDIAN select GENERIC_HARDIRQS_NO__DO_IRQ -config LEMOTE_FULONG - bool "Lemote Fulong mini-PC" +config LEMOTE_FULOONG2E + bool "Lemote Fuloong(2e) mini-PC" select ARCH_SPARSEMEM_ENABLE select CEVT_R4K select CSRC_R4K
arch/mips/Makefile +3 -3
@@ -306,9 +306,9 @@ load-$(CONFIG_WR_PPMC) += 0xffffffff80100000 # # lemote fulong mini-PC board # -core-$(CONFIG_LEMOTE_FULONG) +=arch/mips/lemote/lm2e/ -load-$(CONFIG_LEMOTE_FULONG) +=0xffffffff80100000 -cflags-$(CONFIG_LEMOTE_FULONG) += -I$(srctree)/arch/mips/include/asm/mach-lemote +core-$(CONFIG_LEMOTE_FULOONG2E) +=arch/mips/loongson/fuloong-2e/ +load-$(CONFIG_LEMOTE_FULOONG2E) +=0xffffffff80100000 +cflags-$(CONFIG_LEMOTE_FULOONG2E) += -I$(srctree)/arch/mips/include/asm/mach-loongson # # MIPS Malta board
arch/mips/include/asm/mach-lemote/dma-coherence.h deleted +0 -66
66 lines not on this page · raw message
arch/mips/include/asm/mach-lemote/mc146818rtc.h deleted +0 -36
@@ -1,36 +0,0 @@ -/* -* This file is subject to the terms and conditions of the GNU General Public -* License. See the file "COPYING" in the main directory of this archive -* for more details. -* -* Copyright (C) 1998, 2001, 03, 07 by Ralf Baechle ([email protected]) -* -* RTC routines for PC style attached Dallas chip. -*/ -#ifndef __ASM_MACH_LEMOTE_MC146818RTC_H -#define __ASM_MACH_LEMOTE_MC146818RTC_H - -#include <linux/io.h> - -#define RTC_PORT (x) (0x70 + (x)) -#define RTC_IRQ 8 - -static inline unsigned char CMOS_READ (unsigned long addr) -{ -outb_p (addr,RTC_PORT (0 )); -return inb_p (RTC_PORT (1 )); -} - -static inline void CMOS_WRITE (unsigned char data,unsigned long addr) -{ -outb_p (addr,RTC_PORT (0 )); -outb_p (data,RTC_PORT (1 )); -} - -#define RTC_ALWAYS_BCD 0 - -#ifndef mc146818_decode_year -#define mc146818_decode_year (year) ((year) < 70 ? (year) + 2000 : (year) + 1970) -#endif - -#endif /* __ASM_MACH_LEMOTE_MC146818RTC_H */
arch/mips/include/asm/mach-lemote/pci.h deleted +0 -30
@@ -1,30 +0,0 @@ -/* -* Copyright (c) 2008 Zhang Le <[email protected]> -* -* This program is free software; you can redistribute it -* and/or modify it under the terms of the GNU General -* Public License as published by the Free Software -* Foundation; either version 2 of the License, or (at your -* option) any later version. -* -* This program is distributed in the hope that it will be -* useful, but WITHOUT ANY WARRANTY; without even the implied -* warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR -* PURPOSE. See the GNU General Public License for more -* details. -* -* You should have received a copy of the GNU General Public -* License along with this program; if not, write to the Free -* Software Foundation, Inc., 675 Mass Ave, Cambridge, MA -* 02139, USA. -*/ - -#ifndef _LEMOTE_PCI_H_ -#define _LEMOTE_PCI_H_ - -#define LOONGSON2E_PCI_MEM_START 0x14000000UL -#define LOONGSON2E_PCI_MEM_END 0x1fffffffUL -#define LOONGSON2E_PCI_IO_START 0x00004000UL -#define LOONGSON2E_IO_PORT_BASE 0x1fd00000UL - -#endif /* !_LEMOTE_PCI_H_ */
arch/mips/include/asm/mach-lemote/war.h deleted +0 -25
@@ -1,25 +0,0 @@ -/* -* This file is subject to the terms and conditions of the GNU General Public -* License. See the file "COPYING" in the main directory of this archive -* for more details. -* -* Copyright (C) 2002, 2004, 2007 by Ralf Baechle <[email protected]> -*/ -#ifndef __ASM_MIPS_MACH_LEMOTE_WAR_H -#define __ASM_MIPS_MACH_LEMOTE_WAR_H - -#define R4600_V1_INDEX_ICACHEOP_WAR 0 -#define R4600_V1_HIT_CACHEOP_WAR 0 -#define R4600_V2_HIT_CACHEOP_WAR 0 -#define R5432_CP0_INTERRUPT_WAR 0 -#define BCM1250_M3_WAR 0 -#define SIBYTE_1956_WAR 0 -#define MIPS4K_ICACHE_REFILL_WAR 0 -#define MIPS_CACHE_SYNC_WAR 0 -#define TX49XX_ICACHE_INDEX_INV_WAR 0 -#define RM9000_CDEX_SMP_WAR 0 -#define ICACHE_REFILLS_WORKAROUND_WAR 0 -#define R10000_LLSC_WAR 0 -#define MIPS34K_MISSED_ITLB_WAR 0 - -#endif /* __ASM_MIPS_MACH_LEMOTE_WAR_H */
arch/mips/include/asm/mach-loongson/dma-coherence.h new file +66 -0
66 lines not on this page · raw message
arch/mips/include/asm/mach-loongson/loongson.h new file +14 -0
@@ -0,0 +1,14 @@ +/* +* loongson-specific header file +*/ + +/* loongson internal northbridge initialization */ +extern void bonito_irq_init (void ); + +/* command line */ +extern unsigned long bus_clock, cpu_clock_freq; +extern unsigned long memsize, highmemsize; + +/* loongson-based machines specific reboot setup */ +extern void loongson_reboot_setup (void ); +
arch/mips/include/asm/mach-loongson/mc146818rtc.h new file +36 -0
@@ -0,0 +1,36 @@ +/* +* This file is subject to the terms and conditions of the GNU General Public +* License. See the file "COPYING" in the main directory of this archive +* for more details. +* +* Copyright (C) 1998, 2001, 03, 07 by Ralf Baechle ([email protected]) +* +* RTC routines for PC style attached Dallas chip. +*/ +#ifndef __ASM_MACH_LOONGSON_MC146818RTC_H +#define __ASM_MACH_LOONGSON_MC146818RTC_H + +#include <linux/io.h> + +#define RTC_PORT (x) (0x70 + (x)) +#define RTC_IRQ 8 + +static inline unsigned char CMOS_READ (unsigned long addr) +{ +outb_p (addr,RTC_PORT (0 )); +return inb_p (RTC_PORT (1 )); +} + +static inline void CMOS_WRITE (unsigned char data,unsigned long addr) +{ +outb_p (addr,RTC_PORT (0 )); +outb_p (data,RTC_PORT (1 )); +} + +#define RTC_ALWAYS_BCD 0 + +#ifndef mc146818_decode_year +#define mc146818_decode_year (year) ((year) < 70 ? (year) + 2000 : (year) + 1970) +#endif + +#endif /* __ASM_MACH_LOONGSON_MC146818RTC_H */
arch/mips/include/asm/mach-loongson/pci.h new file +32 -0
@@ -0,0 +1,32 @@ +/* +* Copyright (c) 2008 Zhang Le <[email protected]> +* +* This program is free software; you can redistribute it +* and/or modify it under the terms of the GNU General +* Public License as published by the Free Software +* Foundation; either version 2 of the License, or (at your +* option) any later version. +* +* This program is distributed in the hope that it will be +* useful, but WITHOUT ANY WARRANTY; without even the implied +* warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR +* PURPOSE. See the GNU General Public License for more +* details. +* +* You should have received a copy of the GNU General Public +* License along with this program; if not, write to the Free +* Software Foundation, Inc., 675 Mass Ave, Cambridge, MA +* 02139, USA. +*/ + +#ifndef _LOONGSON_PCI_H_ +#define _LOONGSON_PCI_H_ + +extern struct pci_ops bonito64_pci_ops; + +#define LOONGSON2E_PCI_MEM_START 0x14000000UL +#define LOONGSON2E_PCI_MEM_END 0x1fffffffUL +#define LOONGSON2E_PCI_IO_START 0x00004000UL +#define LOONGSON2E_IO_PORT_BASE 0x1fd00000UL + +#endif /* !_LOONGSON_PCI_H_ */
arch/mips/include/asm/mach-loongson/war.h new file +25 -0
@@ -0,0 +1,25 @@ +/* +* This file is subject to the terms and conditions of the GNU General Public +* License. See the file "COPYING" in the main directory of this archive +* for more details. +* +* Copyright (C) 2002, 2004, 2007 by Ralf Baechle <[email protected]> +*/ +#ifndef __ASM_MIPS_MACH_LOONGSON_WAR_H +#define __ASM_MIPS_MACH_LOONGSON_WAR_H + +#define R4600_V1_INDEX_ICACHEOP_WAR 0 +#define R4600_V1_HIT_CACHEOP_WAR 0 +#define R4600_V2_HIT_CACHEOP_WAR 0 +#define R5432_CP0_INTERRUPT_WAR 0 +#define BCM1250_M3_WAR 0 +#define SIBYTE_1956_WAR 0 +#define MIPS4K_ICACHE_REFILL_WAR 0 +#define MIPS_CACHE_SYNC_WAR 0 +#define TX49XX_ICACHE_INDEX_INV_WAR 0 +#define RM9000_CDEX_SMP_WAR 0 +#define ICACHE_REFILLS_WORKAROUND_WAR 0 +#define R10000_LLSC_WAR 0 +#define MIPS34K_MISSED_ITLB_WAR 0 + +#endif /* __ASM_MIPS_MACH_LOONGSON_WAR_H */
arch/mips/include/asm/mips-boards/bonito64.h +1 -1
@@ -26,7 +26,7 @@/* offsets from base register */ #define BONITO (x) (x) -#elif defined(CONFIG_LEMOTE_FULONG ) +#elif defined(CONFIG_LEMOTE_FULOONG2E )#define BONITO (x) (*(volatile u32 *)((char *)CKSEG1ADDR(BONITO_REG_BASE) + (x)))#define BONITO_IRQ_BASE 32
arch/mips/lemote/lm2e/Makefile deleted +0 -7
@@ -1,7 +0,0 @@ -# -# Makefile for Lemote Fulong mini-PC board. -# - -obj-y += setup.o prom.o reset.o irq.o pci.o bonito-irq.o dbg_io.o mem.o - -EXTRA_CFLAGS += -Werror
arch/mips/lemote/lm2e/bonito-irq.c deleted +0 -74
74 lines not on this page · raw message
arch/mips/lemote/lm2e/dbg_io.c deleted +0 -146
146 lines not on this page · raw message
arch/mips/lemote/lm2e/irq.c deleted +0 -144
144 lines not on this page · raw message
arch/mips/lemote/lm2e/mem.c deleted +0 -23
@@ -1,23 +0,0 @@ -/* -* This program is free software; you can redistribute it and/or modify it -* under the terms of the GNU General Public License as published by the -* Free Software Foundation; either version 2 of the License, or (at your -* option) any later version. -*/ -#include <linux/fs.h> -#include <linux/fcntl.h> -#include <linux/mm.h> - -/* override of arch/mips/mm/cache.c: __uncached_access */ -int __uncached_access (struct file *file,unsigned long addr) -{ -if (file->f_flags &O_SYNC ) -return 1 ; - -/* -* On the Lemote Loongson 2e system, the peripheral registers -* reside between 0x1000:0000 and 0x2000:0000. -*/ -return addr >=__pa (high_memory) || - ((addr >=0x10000000 ) && (addr <0x20000000 )); -}
arch/mips/lemote/lm2e/pci.c deleted +0 -97
97 lines not on this page · raw message
arch/mips/lemote/lm2e/prom.c deleted +0 -97
97 lines not on this page · raw message
arch/mips/lemote/lm2e/reset.c deleted +0 -41
41 lines not on this page · raw message
arch/mips/lemote/lm2e/setup.c deleted +0 -111
111 lines not on this page · raw message
arch/mips/loongson/fuloong-2e/Makefile new file +7 -0
@@ -0,0 +1,7 @@ +# +# Makefile for Lemote Fulong mini-PC board. +# + +obj-y += setup.o prom.o reset.o irq.o pci.o bonito-irq.o dbg_io.o mem.o + +EXTRA_CFLAGS += -Werror
arch/mips/loongson/fuloong-2e/bonito-irq.c new file +73 -0
73 lines not on this page · raw message
arch/mips/loongson/fuloong-2e/dbg_io.c new file +153 -0
153 lines not on this page · raw message
arch/mips/loongson/fuloong-2e/irq.c new file +140 -0
140 lines not on this page · raw message
arch/mips/loongson/fuloong-2e/mem.c new file +23 -0
@@ -0,0 +1,23 @@ +/* +* This program is free software; you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the +* Free Software Foundation; either version 2 of the License, or (at your +* option) any later version. +*/ +#include <linux/fs.h> +#include <linux/fcntl.h> +#include <linux/mm.h> + +/* override of arch/mips/mm/cache.c: __uncached_access */ +int __uncached_access (struct file *file,unsigned long addr) +{ +if (file->f_flags &O_SYNC ) +return 1 ; + +/* +* On the Lemote Loongson 2e system, the peripheral registers +* reside between 0x1000:0000 and 0x2000:0000. +*/ +return addr >=__pa (high_memory) || + ((addr >=0x10000000 ) && (addr <0x20000000 )); +}
arch/mips/loongson/fuloong-2e/pci.c new file +95 -0
95 lines not on this page · raw message
arch/mips/loongson/fuloong-2e/prom.c new file +90 -0
90 lines not on this page · raw message
arch/mips/loongson/fuloong-2e/reset.c new file +37 -0
@@ -0,0 +1,37 @@ +/* +* This program is free software; you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the +* Free Software Foundation; either version 2 of the License, or (at your +* option) any later version. +* +* Copyright (C) 2007 Lemote, Inc. & Institute of Computing Technology +* Author: Fuxin Zhang, [email protected] +*/ +#include <linux/pm.h> + +#include <asm/reboot.h> + +static void loongson_restart (char *command) +{ +#ifdef CONFIG_32BIT + *(unsigned long *)0xbfe00104 &= ~(1 <<2 ); + *(unsigned long *)0xbfe00104 |= (1 <<2 ); +#else + *(unsigned long *)0xffffffffbfe00104 &= ~(1 <<2 ); + *(unsigned long *)0xffffffffbfe00104 |= (1 <<2 ); +#endif + __asm__ __volatile__("jr\t%0" : :"r" (0xbfc00000 )); +} + +static void loongson_halt (void ) +{ +while (1 ) + ; +} + +void loongson_reboot_setup (void ) +{ + _machine_restart = loongson_restart; + _machine_halt = loongson_halt; + pm_power_off = loongson_halt; +}
arch/mips/loongson/fuloong-2e/setup.c new file +108 -0
108 lines not on this page · raw message
arch/mips/pci/Makefile +1 -1
@@ -26,7 +26,7 @@ obj-$(CONFIG_MIPS_COBALT) += fixup-cobalt.o obj-$(CONFIG_SOC_AU1500) += fixup-au1000.o ops-au1000.o obj-$(CONFIG_SOC_AU1550) += fixup-au1000.o ops-au1000.o obj-$(CONFIG_SOC_PNX8550) += fixup-pnx8550.o ops-pnx8550.o -obj-$(CONFIG_LEMOTE_FULONG) += fixup-lm2e.o ops-bonito64.o +obj-$(CONFIG_LEMOTE_FULOONG2E) += fixup-fuloong2e.o ops-bonito64.o obj-$(CONFIG_MIPS_MALTA) += fixup-malta.o obj-$(CONFIG_PMC_MSP7120_GW) += fixup-pmcmsp.o ops-pmcmsp.o obj-$(CONFIG_PMC_MSP7120_EVAL) += fixup-pmcmsp.o ops-pmcmsp.o
arch/mips/pci/fixup-fuloong2e.c new file +242 -0
242 lines not on this page · raw message
arch/mips/pci/fixup-lm2e.c deleted +0 -242
242 lines not on this page · raw message
arch/mips/pci/ops-bonito64.c +9 -7
@@ -29,11 +29,12 @@#define PCI_ACCESS_READ 0#define PCI_ACCESS_WRITE 1 -#ifdef CONFIG_LEMOTE_FULONG +#ifdef CONFIG_LEMOTE_FULOONG2E #define CFG_SPACE_REG (offset) (void *)CKSEG1ADDR(BONITO_PCICFG_BASE | (offset))#define ID_SEL_BEGIN 11#else -#define CFG_SPACE_REG (offset) (void *)CKSEG1ADDR(_pcictrl_bonito_pcicfg + (offset)) +#define CFG_SPACE_REG (offset) \ + (void *)CKSEG1ADDR(_pcictrl_bonito_pcicfg + (offset))#define ID_SEL_BEGIN 10#endif #define MAX_DEV_NUM (31 - ID_SEL_BEGIN)
@@ -42,7 +43,7 @@static int bonito64_pcibios_config_access (unsigned char access_type,struct pci_bus *bus,unsigned int devfn,int where, -u32 * data) +u32 *data) {u32 busnum = bus->number;u32 addr, type;
@@ -77,9 +78,10 @@ static int bonito64_pcibios_config_access(unsigned char access_type, addrp =CFG_SPACE_REG (addr &0xffff );if (access_type ==PCI_ACCESS_WRITE ) {writel (cpu_to_le32 (*data), addrp); -#ifndef CONFIG_LEMOTE_FULONG +#ifndef CONFIG_LEMOTE_FULOONG2E /* Wait till done */ -while (BONITO_PCIMSTAT &0xF ); +while (BONITO_PCIMSTAT &0xF ) + ;#endif }else { *data =le32_to_cpu (readl (addrp));
@@ -107,7 +109,7 @@ static int bonito64_pcibios_config_access(unsigned char access_type,* read/write a 32bit word and mask/modify the data we actually want. */ static int bonito64_pcibios_read (struct pci_bus *bus,unsigned int devfn, -int where,int size,u32 * val) +int where,int size,u32 *val) {u32 data =0 ;
@@ -144,7 +146,7 @@ static int bonito64_pcibios_write(struct pci_bus *bus, unsigned int devfn, data = val; else {if (bonito64_pcibios_config_access (PCI_ACCESS_READ , bus, devfn, - where, &data)) + where, &data))return -1 ;if (size ==1 )
Signature · 1 line
1.6.2.1
PATCH 5/27 remove reference to bonito64.h
In reply to [email protected]From: Wu Zhangjin <[email protected]>
in loongson2e, there is an internal bonito64 compatiable north bridge, but in loongson2f and the later loongson revisions, this will change a lot, so, remove reference from bonito64.h and create a new loongson.h is better.
--- arch/mips/include/asm/mach-loongson/loongson.h | 194 +++++++++++++++++++++++- arch/mips/include/asm/mach-loongson/pci.h | 2 +- arch/mips/include/asm/mips-boards/bonito64.h | 5 - arch/mips/loongson/fuloong-2e/bonito-irq.c | 10 +- arch/mips/loongson/fuloong-2e/irq.c | 23 ++-- arch/mips/loongson/fuloong-2e/pci.c | 15 +- arch/mips/pci/Makefile | 2 +- arch/mips/pci/fixup-fuloong2e.c | 5 +- arch/mips/pci/ops-bonito64.c | 7 - arch/mips/pci/ops-fuloong2e.c | 160 +++++++++++++++++++ 10 files changed, 382 insertions(+), 41 deletions(-) create mode 100644 arch/mips/pci/ops-fuloong2e.c
arch/mips/include/asm/mach-loongson/loongson.h +193 -1
@@ -1,7 +1,19 @@/* -* loongson-specific header file +* Copyright (c) 2009 Philippe Vachon <[email protected]> +* +* Copyright (C) 2009 Lemote, Inc. & Institute of Computing Technology +* Author: Wu Zhangjin <[email protected]> +* +* This program is free software; you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the +* Free Software Foundation; either version 2 of the License, or (at your +* option) any later version. +* */ +#ifndef __LOONGSON_H +#define __LOONGSON_H +/* loongson internal northbridge initialization */ extern void bonito_irq_init (void );
@@ -12,3 +24,183 @@ extern unsigned long memsize, highmemsize;/* loongson-based machines specific reboot setup */ extern void loongson_reboot_setup (void ); +#define LOONGSON_REG (x) \ + (*(u32 *)((char *)CKSEG1ADDR(LOONGSON_REG_BASE) + (x))) +#define LOONGSON_IRQ_BASE 32 + +#define LOONGSON_FLASH_BASE 0x1c000000 +#define LOONGSON_FLASH_SIZE 0x02000000/* 32M */ +#define LOONGSON_FLASH_TOP (LOONGSON_FLASH_BASE+LOONGSON_FLASH_SIZE-1) + +#define LOONGSON_LIO0_BASE 0x1e000000 +#define LOONGSON_LIO0_SIZE 0x01C00000/* 28M */ +#define LOONGSON_LIO0_TOP (LOONGSON_LIO0_BASE+LOONGSON_LIO0_SIZE-1) + +#define LOONGSON_BOOT_BASE 0x1fc00000 +#define LOONGSON_BOOT_SIZE 0x00100000/* 1M */ +#define LOONGSON_BOOT_TOP (LOONGSON_BOOT_BASE+LOONGSON_BOOT_SIZE-1) +#define LOONGSON_REG_BASE 0x1fe00000 +#define LOONGSON_REG_SIZE 0x00100000/* 256Bytes + 256Bytes + ??? */ +#define LOONGSON_REG_TOP (LOONGSON_REG_BASE+LOONGSON_REG_SIZE-1) + +#define LOONGSON_LIO1_BASE 0x1ff00000 +#define LOONGSON_LIO1_SIZE 0x00100000/* 1M */ +#define LOONGSON_LIO1_TOP (LOONGSON_LIO1_BASE+LOONGSON_LIO1_SIZE-1) + +#define LOONGSON_PCILO0_BASE 0x10000000 +#define LOONGSON_PCILO1_BASE 0x14000000 +#define LOONGSON_PCILO2_BASE 0x18000000 +#define LOONGSON_PCILO_BASE LOONGSON_PCILO0_BASE +#define LOONGSON_PCILO_SIZE 0x0c000000/* 64M * 3 */ +#define LOONGSON_PCILO_TOP (LOONGSON_PCILO0_BASE+LOONGSON_PCILO_SIZE-1) + +#define LOONGSON_PCICFG_BASE 0x1fe80000 +#define LOONGSON_PCICFG_SIZE 0x00000800/* 2K */ +#define LOONGSON_PCICFG_TOP (LOONGSON_PCICFG_BASE+LOONGSON_PCICFG_SIZE-1) +#define LOONGSON_PCIIO_BASE 0x1fd00000 +#define LOONGSON_PCIIO_SIZE 0x00100000/* 1M */ +#define LOONGSON_PCIIO_TOP (LOONGSON_PCIIO_BASE+LOONGSON_PCIIO_SIZE-1) + +/* Loongson Register Bases */ + +#define LOONGSON_PCICONFIGBASE 0x00 +#define LOONGSON_REGBASE 0x100 + +/* PCI Configuration Registers */ + +#define LOONGSON_PCI_REG (x) LOONGSON_REG(LOONGSON_PCICONFIGBASE + (x)) +#define LOONGSON_PCIDID LOONGSON_PCI_REG(0x00) +#define LOONGSON_PCICMD LOONGSON_PCI_REG(0x04) +#define LOONGSON_PCICLASS LOONGSON_PCI_REG(0x08) +#define LOONGSON_PCILTIMER LOONGSON_PCI_REG(0x0c) +#define LOONGSON_PCIBASE0 LOONGSON_PCI_REG(0x10) +#define LOONGSON_PCIBASE1 LOONGSON_PCI_REG(0x14) +#define LOONGSON_PCIBASE2 LOONGSON_PCI_REG(0x18) +#define LOONGSON_PCIBASE3 LOONGSON_PCI_REG(0x1c) +#define LOONGSON_PCIBASE4 LOONGSON_PCI_REG(0x20) +#define LOONGSON_PCIEXPRBASE LOONGSON_PCI_REG(0x30) +#define LOONGSON_PCIINT LOONGSON_PCI_REG(0x3c) + +#define LOONGSON_PCI_ISR4C LOONGSON_PCI_REG(0x4c) + +#define LOONGSON_PCICMD_PERR_CLR 0x80000000 +#define LOONGSON_PCICMD_SERR_CLR 0x40000000 +#define LOONGSON_PCICMD_MABORT_CLR 0x20000000 +#define LOONGSON_PCICMD_MTABORT_CLR 0x10000000 +#define LOONGSON_PCICMD_TABORT_CLR 0x08000000 +#define LOONGSON_PCICMD_MPERR_CLR 0x01000000 +#define LOONGSON_PCICMD_PERRRESPEN 0x00000040 +#define LOONGSON_PCICMD_ASTEPEN 0x00000080 +#define LOONGSON_PCICMD_SERREN 0x00000100 +#define LOONGSON_PCILTIMER_BUSLATENCY 0x0000ff00 +#define LOONGSON_PCILTIMER_BUSLATENCY_SHIFT 8 + +/* Loongson h/w Configuration */ + +#define LOONGSON_GENCFG_OFFSET 0x4 +#define LOONGSON_GENCFG LOONGSON_REG(LOONGSON_REGBASE + LOONGSON_GENCFG_OFFSET) + +#define LOONGSON_GENCFG_DEBUGMODE 0x00000001 +#define LOONGSON_GENCFG_SNOOPEN 0x00000002 +#define LOONGSON_GENCFG_CPUSELFRESET 0x00000004 + +#define LOONGSON_GENCFG_FORCE_IRQA 0x00000008 +#define LOONGSON_GENCFG_IRQA_ISOUT 0x00000010 +#define LOONGSON_GENCFG_IRQA_FROM_INT1 0x00000020 +#define LOONGSON_GENCFG_BYTESWAP 0x00000040 + +#define LOONGSON_GENCFG_UNCACHED 0x00000080 +#define LOONGSON_GENCFG_PREFETCHEN 0x00000100 +#define LOONGSON_GENCFG_WBEHINDEN 0x00000200 +#define LOONGSON_GENCFG_CACHEALG 0x00000c00 +#define LOONGSON_GENCFG_CACHEALG_SHIFT 10 +#define LOONGSON_GENCFG_PCIQUEUE 0x00001000 +#define LOONGSON_GENCFG_CACHESTOP 0x00002000 +#define LOONGSON_GENCFG_MSTRBYTESWAP 0x00004000 +#define LOONGSON_GENCFG_BUSERREN 0x00008000 +#define LOONGSON_GENCFG_NORETRYTIMEOUT 0x00010000 +#define LOONGSON_GENCFG_SHORTCOPYTIMEOUT 0x00020000 + +/* PCI address map control */ + +#define LOONGSON_PCIMAP LOONGSON_REG(LOONGSON_REGBASE + 0x10) +#define LOONGSON_PCIMEMBASECFG LOONGSON_REG(LOONGSON_REGBASE + 0x14) +#define LOONGSON_PCIMAP_CFG LOONGSON_REG(LOONGSON_REGBASE + 0x18) + +/* GPIO Regs - r/w */ + +#define LOONGSON_GPIODATA LOONGSON_REG(LOONGSON_REGBASE + 0x1c) +#define LOONGSON_GPIOIE LOONGSON_REG(LOONGSON_REGBASE + 0x20) + +/* ICU Configuration Regs - r/w */ + +#define LOONGSON_INTEDGE LOONGSON_REG(LOONGSON_REGBASE + 0x24) +#define LOONGSON_INTSTEER LOONGSON_REG(LOONGSON_REGBASE + 0x28) +#define LOONGSON_INTPOL LOONGSON_REG(LOONGSON_REGBASE + 0x2c) + +/* ICU Enable Regs - IntEn & IntISR are r/o. */ + +#define LOONGSON_INTENSET LOONGSON_REG(LOONGSON_REGBASE + 0x30) +#define LOONGSON_INTENCLR LOONGSON_REG(LOONGSON_REGBASE + 0x34) +#define LOONGSON_INTEN LOONGSON_REG(LOONGSON_REGBASE + 0x38) +#define LOONGSON_INTISR LOONGSON_REG(LOONGSON_REGBASE + 0x3c) + +/* ICU */ +#define LOONGSON_ICU_MBOXES 0x0000000f +#define LOONGSON_ICU_MBOXES_SHIFT 0 +#define LOONGSON_ICU_DMARDY 0x00000010 +#define LOONGSON_ICU_DMAEMPTY 0x00000020 +#define LOONGSON_ICU_COPYRDY 0x00000040 +#define LOONGSON_ICU_COPYEMPTY 0x00000080 +#define LOONGSON_ICU_COPYERR 0x00000100 +#define LOONGSON_ICU_PCIIRQ 0x00000200 +#define LOONGSON_ICU_MASTERERR 0x00000400 +#define LOONGSON_ICU_SYSTEMERR 0x00000800 +#define LOONGSON_ICU_DRAMPERR 0x00001000 +#define LOONGSON_ICU_RETRYERR 0x00002000 +#define LOONGSON_ICU_GPIOS 0x01ff0000 +#define LOONGSON_ICU_GPIOS_SHIFT 16 +#define LOONGSON_ICU_GPINS 0x7e000000 +#define LOONGSON_ICU_GPINS_SHIFT 25 +#define LOONGSON_ICU_MBOX (N ) (1<<(LOONGSON_ICU_MBOXES_SHIFT+(N))) +#define LOONGSON_ICU_GPIO (N ) (1<<(LOONGSON_ICU_GPIOS_SHIFT+(N))) +#define LOONGSON_ICU_GPIN (N ) (1<<(LOONGSON_ICU_GPINS_SHIFT+(N))) + +/* PCI prefetch window base & mask */ + +#define LOONGSON_MEM_WIN_BASE_L LOONGSON_REG(LOONGSON_REGBASE + 0x40) +#define LOONGSON_MEM_WIN_BASE_H LOONGSON_REG(LOONGSON_REGBASE + 0x44) +#define LOONGSON_MEM_WIN_MASK_L LOONGSON_REG(LOONGSON_REGBASE + 0x48) +#define LOONGSON_MEM_WIN_MASK_H LOONGSON_REG(LOONGSON_REGBASE + 0x4c) + +/* PCI_Hit*_Sel_* */ + +#define LOONGSON_PCI_HIT0_SEL_L LOONGSON_REG(LOONGSON_REGBASE + 0x50) +#define LOONGSON_PCI_HIT0_SEL_H LOONGSON_REG(LOONGSON_REGBASE + 0x54) +#define LOONGSON_PCI_HIT1_SEL_L LOONGSON_REG(LOONGSON_REGBASE + 0x58) +#define LOONGSON_PCI_HIT1_SEL_H LOONGSON_REG(LOONGSON_REGBASE + 0x5c) +#define LOONGSON_PCI_HIT2_SEL_L LOONGSON_REG(LOONGSON_REGBASE + 0x60) +#define LOONGSON_PCI_HIT2_SEL_H LOONGSON_REG(LOONGSON_REGBASE + 0x64) + +/* PXArb Config & Status */ + +#define LOONGSON_PXARB_CFG LOONGSON_REG(LOONGSON_REGBASE + 0x68) +#define LOONGSON_PXARB_STATUS LOONGSON_REG(LOONGSON_REGBASE + 0x6c) + +/* Chip Config */ +#define LOONGSON_CHIPCFG0 LOONGSON_REG(LOONGSON_REGBASE + 0x80) + +/* pcimap */ + +#define LOONGSON_PCIMAP_PCIMAP_LO0 0x0000003f +#define LOONGSON_PCIMAP_PCIMAP_LO0_SHIFT 0 +#define LOONGSON_PCIMAP_PCIMAP_LO1 0x00000fc0 +#define LOONGSON_PCIMAP_PCIMAP_LO1_SHIFT 6 +#define LOONGSON_PCIMAP_PCIMAP_LO2 0x0003f000 +#define LOONGSON_PCIMAP_PCIMAP_LO2_SHIFT 12 +#define LOONGSON_PCIMAP_PCIMAP_2 0x00040000 +#define LOONGSON_PCIMAP_WIN (WIN ,ADDR ) \ + ((((ADDR)>>26) & LOONGSON_PCIMAP_PCIMAP_LO0) << ((WIN)*6)) + +#endif /* __LOONGSON_H */ +
arch/mips/include/asm/mach-loongson/pci.h +1 -1
@@ -22,7 +22,7 @@#ifndef _LOONGSON_PCI_H_#define _LOONGSON_PCI_H_ -extern struct pci_ops bonito64_pci_ops; +extern struct pci_ops loongson_pci_ops;#define LOONGSON2E_PCI_MEM_START 0x14000000UL#define LOONGSON2E_PCI_MEM_END 0x1fffffffUL
arch/mips/include/asm/mips-boards/bonito64.h +0 -5
@@ -26,11 +26,6 @@/* offsets from base register */ #define BONITO (x) (x) -#elif defined(CONFIG_LEMOTE_FULOONG2E ) - -#define BONITO (x) (*(volatile u32 *)((char *)CKSEG1ADDR(BONITO_REG_BASE) + (x))) -#define BONITO_IRQ_BASE 32 -#else /*
arch/mips/loongson/fuloong-2e/bonito-irq.c +5 -5
@@ -34,18 +34,18 @@#include <linux/interrupt.h> #include <linux/irq.h> -#include <asm/mips-boards/bonito64.h> +#include <loongson.h> static inline void bonito_irq_enable (unsigned int irq) { -BONITO_INTENSET = (1 << (irq -BONITO_IRQ_BASE )); +LOONGSON_INTENSET = (1 << (irq -LOONGSON_IRQ_BASE ));mmiowb (); }static inline void bonito_irq_disable (unsigned int irq) { -BONITO_INTENCLR = (1 << (irq -BONITO_IRQ_BASE )); +LOONGSON_INTENCLR = (1 << (irq -LOONGSON_IRQ_BASE ));mmiowb (); }
@@ -66,8 +66,8 @@ void bonito_irq_init(void) {u32 i; -for (i =BONITO_IRQ_BASE ; i <BONITO_IRQ_BASE +32 ; i++) +for (i =LOONGSON_IRQ_BASE ; i <LOONGSON_IRQ_BASE +32 ; i++)set_irq_chip_and_handler (i, &bonito_irq_type, handle_level_irq); -setup_irq (BONITO_IRQ_BASE +10 , &dma_timeout_irqaction); +setup_irq (LOONGSON_IRQ_BASE +10 , &dma_timeout_irqaction); }
arch/mips/loongson/fuloong-2e/irq.c +11 -12
@@ -32,7 +32,6 @@#include <asm/irq_cpu.h> #include <asm/i8259.h> #include <asm/mipsregs.h> -#include <asm/mips-boards/bonito64.h> #include <loongson.h>
@@ -45,21 +44,21 @@ static void bonito_irqdispatch(void)int i;/* workaround the IO dma problem: let cpu looping to allow DMA finish */ - int_status =BONITO_INTISR ; + int_status =LOONGSON_INTISR ;if (int_status & (1 <<10 )) {while (int_status & (1 <<10 )) {udelay (1 ); - int_status =BONITO_INTISR ; + int_status =LOONGSON_INTISR ; } }/* Get pending sources, masked by current enables */ - int_status =BONITO_INTISR &BONITO_INTEN ; + int_status =LOONGSON_INTISR &LOONGSON_INTEN ;if (int_status !=0 ) { i =__ffs (int_status); int_status &= ~(1 << i); -do_IRQ (BONITO_IRQ_BASE + i); +do_IRQ (LOONGSON_IRQ_BASE + i); } }
@@ -104,15 +103,15 @@ void __init arch_init_irq(void)local_irq_disable ();/* most bonito irq should be level triggered */ -BONITO_INTEDGE =BONITO_ICU_SYSTEMERR |BONITO_ICU_MASTERERR | -BONITO_ICU_RETRYERR |BONITO_ICU_MBOXES ; -BONITO_INTSTEER =0 ; +LOONGSON_INTEDGE =LOONGSON_ICU_SYSTEMERR |LOONGSON_ICU_MASTERERR | +LOONGSON_ICU_RETRYERR |LOONGSON_ICU_MBOXES ; +LOONGSON_INTSTEER =0 ;/* * Mask out all interrupt by writing "1" to all bit position in * the interrupt reset reg. */ -BONITO_INTENCLR = ~0 ; +LOONGSON_INTENCLR = ~0 ;/* init all controller * 0-15 ------> i8259 interrupt
@@ -126,10 +125,10 @@ void __init arch_init_irq(void)bonito_irq_init ();/* -printk("GPIODATA=%x, GPIOIE=%x\n", BONITO_GPIODATA, BONITO_GPIOIE); +printk("GPIODATA=%x, GPIOIE=%x\n", LOONGSON_GPIODATA, LOONGSON_GPIOIE); printk("INTEN=%x, INTSET=%x, INTCLR=%x, INTISR=%x\n", -BONITO_INTEN, BONITO_INTENSET, -BONITO_INTENCLR, BONITO_INTISR); +LOONGSON_INTEN, LOONGSON_INTENSET, +LOONGSON_INTENCLR, LOONGSON_INTISR); */ /* bonito irq at IP2 */
arch/mips/loongson/fuloong-2e/pci.c +8 -7
@@ -29,7 +29,8 @@#include <linux/pci.h> #include <linux/kernel.h> #include <linux/init.h> -#include <asm/mips-boards/bonito64.h> + +#include <loongson.h> #include <pci.h> static struct resource loongson2e_pci_mem_resource = {
@@ -47,7 +48,7 @@ static struct resource loongson2e_pci_io_resource = { };static struct pci_controller loongson2e_pci_controller = { - .pci_ops = &bonito64_pci_ops, + .pci_ops = &loongson_pci_ops, .io_resource = &loongson2e_pci_io_resource, .mem_resource = &loongson2e_pci_mem_resource, .mem_offset =0x00000000UL ,
@@ -64,17 +65,17 @@ static void __init ict_pcimap(void)* pcimap: bit18,pcimap_2; bit[17-12],lo2;bit[11-6],lo1;bit[5-0],lo0 */ /* 1,00 0110 ,0001 01,00 0000 */ -BONITO_PCIMAP =0x46140 ; +LOONGSON_PCIMAP =0x46140 ;/* 1, 00 0010, 0000,01, 00 0000 */ -/* BONITO_PCIMAP = 0x42040; */ +/* LOONGSON_PCIMAP = 0x42040; */ /* * PCI to local mapping: [2G,2G+256M] -> [0,256M] */ -BONITO_PCIBASE0 =0x80000000 ; -BONITO_PCIBASE1 =0x00800000 ; -BONITO_PCIBASE2 =0x90000000 ; +LOONGSON_PCIBASE0 =0x80000000 ; +LOONGSON_PCIBASE1 =0x00800000 ; +LOONGSON_PCIBASE2 =0x90000000 ; }
arch/mips/pci/Makefile +1 -1
@@ -26,7 +26,7 @@ obj-$(CONFIG_MIPS_COBALT) += fixup-cobalt.o obj-$(CONFIG_SOC_AU1500) += fixup-au1000.o ops-au1000.o obj-$(CONFIG_SOC_AU1550) += fixup-au1000.o ops-au1000.o obj-$(CONFIG_SOC_PNX8550) += fixup-pnx8550.o ops-pnx8550.o -obj-$(CONFIG_LEMOTE_FULOONG2E) += fixup-fuloong2e.o ops-bonito64.o +obj-$(CONFIG_LEMOTE_FULOONG2E) += fixup-fuloong2e.o ops-fuloong2e.o obj-$(CONFIG_MIPS_MALTA) += fixup-malta.o obj-$(CONFIG_PMC_MSP7120_GW) += fixup-pmcmsp.o ops-pmcmsp.o obj-$(CONFIG_PMC_MSP7120_EVAL) += fixup-pmcmsp.o ops-pmcmsp.o
arch/mips/pci/fixup-fuloong2e.c +3 -2
@@ -31,7 +31,8 @@*/ #include <linux/init.h> #include <linux/pci.h> -#include <asm/mips-boards/bonito64.h> + +#include <loongson.h> /* South bridge slot number is set by the pci probe process */ static u8 sb_slot =5 ;
@@ -53,7 +54,7 @@ int __init pcibios_map_irq(struct pci_dev *dev, u8 slot, u8 pin)break ; } }else { - irq =BONITO_IRQ_BASE +25 + pin; + irq =LOONGSON_IRQ_BASE +25 + pin; }return irq;
arch/mips/pci/ops-bonito64.c +0 -7
@@ -29,14 +29,9 @@#define PCI_ACCESS_READ 0#define PCI_ACCESS_WRITE 1 -#ifdef CONFIG_LEMOTE_FULOONG2E -#define CFG_SPACE_REG (offset) (void *)CKSEG1ADDR(BONITO_PCICFG_BASE | (offset)) -#define ID_SEL_BEGIN 11 -#else #define CFG_SPACE_REG (offset) \ (void *)CKSEG1ADDR(_pcictrl_bonito_pcicfg + (offset))#define ID_SEL_BEGIN 10 -#endif #define MAX_DEV_NUM (31 - ID_SEL_BEGIN)
@@ -78,11 +73,9 @@ static int bonito64_pcibios_config_access(unsigned char access_type, addrp =CFG_SPACE_REG (addr &0xffff );if (access_type ==PCI_ACCESS_WRITE ) {writel (cpu_to_le32 (*data), addrp); -#ifndef CONFIG_LEMOTE_FULOONG2E /* Wait till done */ while (BONITO_PCIMSTAT &0xF ) ; -#endif }else { *data =le32_to_cpu (readl (addrp)); }
arch/mips/pci/ops-fuloong2e.c new file +160 -0
160 lines not on this page · raw message
Signature · 1 line
1.6.2.1
PATCH 6/27 divide the files to the smallest logic unit
In reply to [email protected]From: Wu Zhangjin <[email protected]>
to enhance the maintainability and scalability of the source code, there is a need to divide the files to the smallest logic function unit.
at the same time, the header files references are cleaned up, and some loongson2e* names are changed to loongson* for future source code sharing between loongson-2e and loongson-2f
--- arch/mips/include/asm/mach-loongson/loongson.h | 4 + arch/mips/include/asm/mach-loongson/pci.h | 7 +- arch/mips/loongson/fuloong-2e/Makefile | 3 +- arch/mips/loongson/fuloong-2e/bonito-irq.c | 7 +-- arch/mips/loongson/fuloong-2e/cmdline.c | 77 ++++++++++++++++++ arch/mips/loongson/fuloong-2e/init.c | 40 +++++++++ arch/mips/loongson/fuloong-2e/irq.c | 5 +- arch/mips/loongson/fuloong-2e/mem.c | 18 ++++- arch/mips/loongson/fuloong-2e/misc.c | 13 +++ arch/mips/loongson/fuloong-2e/pci.c | 30 +++---- arch/mips/loongson/fuloong-2e/prom.c | 90 --------------------- arch/mips/loongson/fuloong-2e/setup.c | 103 ++++++++---------------- arch/mips/loongson/fuloong-2e/time.c | 27 ++++++ 13 files changed, 230 insertions(+), 194 deletions(-) create mode 100644 arch/mips/loongson/fuloong-2e/cmdline.c create mode 100644 arch/mips/loongson/fuloong-2e/init.c create mode 100644 arch/mips/loongson/fuloong-2e/misc.c delete mode 100644 arch/mips/loongson/fuloong-2e/prom.c create mode 100644 arch/mips/loongson/fuloong-2e/time.c
arch/mips/include/asm/mach-loongson/loongson.h +4 -0
@@ -24,6 +24,10 @@ extern unsigned long memsize, highmemsize;/* loongson-based machines specific reboot setup */ extern void loongson_reboot_setup (void ); +/* loongson-specific command line and memory initialization */ +extern void __init prom_init_memory (void ); +extern void __init prom_init_cmdline (void ); +#define LOONGSON_REG (x) \ (*(u32 *)((char *)CKSEG1ADDR(LOONGSON_REG_BASE) + (x)))#define LOONGSON_IRQ_BASE 32
arch/mips/include/asm/mach-loongson/pci.h +3 -4
@@ -24,9 +24,8 @@extern struct pci_ops loongson_pci_ops; -#define LOONGSON2E_PCI_MEM_START 0x14000000UL -#define LOONGSON2E_PCI_MEM_END 0x1fffffffUL -#define LOONGSON2E_PCI_IO_START 0x00004000UL -#define LOONGSON2E_IO_PORT_BASE 0x1fd00000UL +#define LOONGSON_PCI_MEM_START 0x14000000UL +#define LOONGSON_PCI_MEM_END 0x1fffffffUL +#define LOONGSON_PCI_IO_START 0x00004000UL#endif /* !_LOONGSON_PCI_H_ */
arch/mips/loongson/fuloong-2e/Makefile +2 -1
@@ -2,6 +2,7 @@ # Makefile for Lemote Fulong mini-PC board. # -obj-y += setup.o prom.o reset.o irq.o pci.o bonito-irq.o dbg_io.o mem.o +obj-y += setup.o init.o cmdline.o time.o reset.o irq.o \ + pci.o bonito-irq.o dbg_io.o mem.o misc.o EXTRA_CFLAGS += -Werror
arch/mips/loongson/fuloong-2e/bonito-irq.c +1 -6
@@ -27,16 +27,11 @@* 675 Mass Ave, Cambridge, MA 02139, USA. * */ -#include <linux/errno.h> -#include <linux/init.h> -#include <linux/io.h> -#include <linux/types.h> +#include <linux/interrupt.h> -#include <linux/irq.h> #include <loongson.h> -static inline void bonito_irq_enable (unsigned int irq) {LOONGSON_INTENSET = (1 << (irq -LOONGSON_IRQ_BASE ));
arch/mips/loongson/fuloong-2e/cmdline.c new file +77 -0
77 lines not on this page · raw message
arch/mips/loongson/fuloong-2e/init.c new file +40 -0
@@ -0,0 +1,40 @@ +/* +* Based on Ocelot Linux port, which is +* Copyright 2001 MontaVista Software Inc. +* Author: [email protected] or [email protected] +* +* Copyright 2003 ICT CAS +* Author: Michael Guo <[email protected]> +* +* Copyright (C) 2007 Lemote Inc. & Insititute of Computing Technology +* Author: Fuxin Zhang, [email protected] +* +* This program is free software; you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the +* Free Software Foundation; either version 2 of the License, or (at your +* option) any later version. +*/ + +#include <linux/bootmem.h> + +#include <asm/bootinfo.h> +#include <asm/cpu.h> + +#include <loongson.h> + +void __init prom_init (void ) +{ +/* init mach type, does we need to init it?? */ + mips_machtype =PRID_IMP_LOONGSON2 ; + +/* init several base address */ +set_io_port_base ((unsigned long ) +ioremap (LOONGSON_PCIIO_BASE ,LOONGSON_PCIIO_SIZE )); + +prom_init_cmdline (); +prom_init_memory (); +} + +void __init prom_free_prom_memory (void ) +{ +}
arch/mips/loongson/fuloong-2e/irq.c +1 -4
@@ -23,15 +23,12 @@* 675 Mass Ave, Cambridge, MA 02139, USA. * */ +#include <linux/delay.h> -#include <linux/io.h> -#include <linux/init.h> #include <linux/interrupt.h> -#include <linux/irq.h> #include <asm/irq_cpu.h> #include <asm/i8259.h> -#include <asm/mipsregs.h> #include <loongson.h>
arch/mips/loongson/fuloong-2e/mem.c +17 -1
@@ -4,9 +4,25 @@* Free Software Foundation; either version 2 of the License, or (at your * option) any later version. */ +#include <linux/fs.h> -#include <linux/fcntl.h> #include <linux/mm.h> +#include <linux/init.h> + +#include <asm/bootinfo.h> + +#include <loongson.h> + +void __init prom_init_memory (void ) +{ +add_memory_region (0x0 , (memsize <<20 ),BOOT_MEM_RAM ); +#ifdef CONFIG_64BIT +if (highmemsize >0 ) { +add_memory_region (0x20000000 , + highmemsize <<20 ,BOOT_MEM_RAM ); + } +#endif /* CONFIG_64BIT */ +}/* override of arch/mips/mm/cache.c: __uncached_access */ int __uncached_access (struct file *file,unsigned long addr)
arch/mips/loongson/fuloong-2e/misc.c new file +13 -0
@@ -0,0 +1,13 @@ +/* Copyright (C) 2009 Lemote Inc. & Insititute of Computing Technology +* Author: Wu Zhangjin, [email protected] +* +* This program is free software; you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the +* Free Software Foundation; either version 2 of the License, or (at your +* option) any later version. +*/ + +const char *get_system_type (void ) +{ +return "fuloong-2e" ; +}
arch/mips/loongson/fuloong-2e/pci.c +12 -18
@@ -25,32 +25,29 @@* 675 Mass Ave, Cambridge, MA 02139, USA. * */ -#include <linux/types.h> #include <linux/pci.h> -#include <linux/kernel.h> -#include <linux/init.h> #include <loongson.h> #include <pci.h> -static struct resource loongson2e_pci_mem_resource = { - .name ="LOONGSON2E PCI MEM" , - .start =LOONGSON2E_PCI_MEM_START , - .end =LOONGSON2E_PCI_MEM_END , +static struct resource loongson_pci_mem_resource = { + .name ="LOONGSON PCI MEM" , + .start =LOONGSON_PCI_MEM_START , + .end =LOONGSON_PCI_MEM_END , .flags =IORESOURCE_MEM , }; -static struct resource loongson2e_pci_io_resource = { - .name ="LOONGSON2E PCI IO MEM" , - .start =LOONGSON2E_PCI_IO_START , +static struct resource loongson_pci_io_resource = { + .name ="LOONGSON PCI IO MEM" , + .start =LOONGSON_PCI_IO_START , .end =IO_SPACE_LIMIT , .flags =IORESOURCE_IO , }; -static struct pci_controller loongson2e_pci_controller = { +static struct pci_controller loongson_pci_controller = { .pci_ops = &loongson_pci_ops, - .io_resource = &loongson2e_pci_io_resource, - .mem_resource = &loongson2e_pci_mem_resource, + .io_resource = &loongson_pci_io_resource, + .mem_resource = &loongson_pci_mem_resource, .mem_offset =0x00000000UL , .io_offset =0x00000000UL , };
@@ -83,12 +80,9 @@ static int __init pcibios_init(void) {ict_pcimap (); - loongson2e_pci_controller.io_map_base = - (unsigned long )ioremap (LOONGSON2E_IO_PORT_BASE , - loongson2e_pci_io_resource.end - - loongson2e_pci_io_resource.start +1 ); + loongson_pci_controller.io_map_base = mips_io_port_base; -register_pci_controller (&loongson2e_pci_controller); +register_pci_controller (&loongson_pci_controller);return 0 ; }
arch/mips/loongson/fuloong-2e/prom.c deleted +0 -90
90 lines not on this page · raw message
arch/mips/loongson/fuloong-2e/setup.c +33 -70
141 lines not on this page · raw message
arch/mips/loongson/fuloong-2e/time.c new file +27 -0
@@ -0,0 +1,27 @@ +/* +* board dependent boot routines +* +* Copyright (C) 2007 Lemote Inc. & Insititute of Computing Technology +* Author: Fuxin Zhang, [email protected] +* +* This program is free software; you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the +* Free Software Foundation; either version 2 of the License, or (at your +* option) any later version. +*/ + +#include <asm/mc146818-time.h> +#include <asm/time.h> + +#include <loongson.h> + +unsigned long read_persistent_clock (void ) +{ +return mc146818_get_cmos_time (); +} + +void __init plat_time_init (void ) +{ +/* setup mips r4k timer */ + mips_hpt_frequency = cpu_clock_freq /2 ; +}
Signature · 1 line
1.6.2.1
PATCH 7/27 replace tons of magic numbers by understandable symbols
In reply to [email protected]From: Wu Zhangjin <[email protected]>
tons of magic numbers are replaced by understandable symbols, and two new header files are added to support this substitution.
--- arch/mips/include/asm/mach-loongson/loongson.h | 3 ++ arch/mips/include/asm/mach-loongson/machine.h | 27 ++++++++++++++++++ arch/mips/include/asm/mach-loongson/mem.h | 8 +++++ arch/mips/loongson/fuloong-2e/bonito-irq.c | 3 +- arch/mips/loongson/fuloong-2e/dbg_io.c | 12 +++---- arch/mips/loongson/fuloong-2e/irq.c | 7 ++-- arch/mips/loongson/fuloong-2e/mem.c | 9 +++-- arch/mips/loongson/fuloong-2e/misc.c | 4 ++- arch/mips/loongson/fuloong-2e/pci.c | 36 ++++++++++++++++-------- arch/mips/loongson/fuloong-2e/reset.c | 19 +++++++----- arch/mips/loongson/fuloong-2e/setup.c | 5 ++- 11 files changed, 96 insertions(+), 37 deletions(-) create mode 100644 arch/mips/include/asm/mach-loongson/machine.h create mode 100644 arch/mips/include/asm/mach-loongson/mem.h
arch/mips/include/asm/mach-loongson/loongson.h +3 -0
@@ -14,6 +14,9 @@#ifndef __LOONGSON_H#define __LOONGSON_H +#include <linux/io.h> +#include <linux/init.h> +/* loongson internal northbridge initialization */ extern void bonito_irq_init (void );
arch/mips/include/asm/mach-loongson/machine.h new file +27 -0
@@ -0,0 +1,27 @@ +/* +* board-specific header file +* +* Copyright (c) 2009 Wu Zhangjin <[email protected]> +* +* This program is free software; you can redistribute it +* and/or modify it under the terms of the GNU General +* Public License as published by the Free Software +* Foundation; either version 2 of the License, or (at your +* option) any later version. +*/ + +#ifndef __MACHINE_H +#define __MACHINE_H + +#define MACH_NAME "lemote-fuloong(2e)" + +#define LOONGSON_UART_BASE 0x1fd003f8 + +#define LOONGSON_NORTH_BRIDGE_IRQ (MIPS_CPU_IRQ_BASE + 2) +#define LOONGSON_UART_IRQ (MIPS_CPU_IRQ_BASE + 4) +#define LOONGSON_SOUTH_BRIDGE_IRQ (MIPS_CPU_IRQ_BASE + 5) +#define LOONGSON_TIMER_IRQ (MIPS_CPU_IRQ_BASE + 7) +#define LOONGSON_DMATIMEOUT_IRQ (LOONGSON_IRQ_BASE + 10) + + +#endif /* ! __MACHINE_H */
arch/mips/include/asm/mach-loongson/mem.h new file +8 -0
@@ -0,0 +1,8 @@ +#ifndef __MEM_H +#define __MEM_H + +#define LOONGSON_HIGHMEM_START 0x20000000 +#define LOONGSON_MMIO_MEM_START 0x10000000 +#define LOONGSON_MMIO_MEM_END 0x20000000 + +#endif /* !__MEM_H */
arch/mips/loongson/fuloong-2e/bonito-irq.c +2 -1
@@ -31,6 +31,7 @@#include <linux/interrupt.h> #include <loongson.h> +#include <machine.h> static inline void bonito_irq_enable (unsigned int irq) {
@@ -64,5 +65,5 @@ void bonito_irq_init(void)for (i =LOONGSON_IRQ_BASE ; i <LOONGSON_IRQ_BASE +32 ; i++)set_irq_chip_and_handler (i, &bonito_irq_type, handle_level_irq); -setup_irq (LOONGSON_IRQ_BASE +10 , &dma_timeout_irqaction); +setup_irq (LOONGSON_DMATIMEOUT_IRQ , &dma_timeout_irqaction); }
arch/mips/loongson/fuloong-2e/dbg_io.c +5 -7
@@ -28,12 +28,13 @@* */ -#include <linux/io.h> -#include <linux/init.h> #include <linux/types.h> #include <asm/serial.h> +#include <loongson.h> +#include <machine.h> +#define UART16550_BAUD_2400 2400#define UART16550_BAUD_4800 4800#define UART16550_BAUD_9600 9600
@@ -59,11 +60,8 @@/* ----------------------------------------------------- */ /* === CONFIG === */ -#ifdef CONFIG_64BIT -#define BASE (0xffffffffbfd003f8) -#else -#define BASE (0xbfd003f8) -#endif + +#define BASE ioremap_nocache(LOONGSON_UART_BASE, 8)#define MAX_BAUD BASE_BAUD/* === END OF CONFIG === */
arch/mips/loongson/fuloong-2e/irq.c +4 -3
@@ -31,6 +31,7 @@#include <asm/i8259.h> #include <loongson.h> +#include <machine.h> /* * the first level int-handler will jump here if it is a bonito irq
@@ -75,7 +76,7 @@ asmlinkage void plat_irq_dispatch(void)unsigned int pending =read_c0_cause () &read_c0_status () &ST0_IM ;if (pending &CAUSEF_IP7 ) -do_IRQ (MIPS_CPU_IRQ_BASE +7 ); +do_IRQ (LOONGSON_TIMER_IRQ );else if (pending &CAUSEF_IP5 )i8259_irqdispatch ();else if (pending &CAUSEF_IP2 )
@@ -129,8 +130,8 @@ void __init arch_init_irq(void)*/ /* bonito irq at IP2 */ -setup_irq (MIPS_CPU_IRQ_BASE +2 , &cascade_irqaction); +setup_irq (LOONGSON_NORTH_BRIDGE_IRQ , &cascade_irqaction);/* 8259 irq at IP5 */ -setup_irq (MIPS_CPU_IRQ_BASE +5 , &cascade_irqaction); +setup_irq (LOONGSON_SOUTH_BRIDGE_IRQ , &cascade_irqaction); }
arch/mips/loongson/fuloong-2e/mem.c +5 -4
@@ -7,18 +7,18 @@#include <linux/fs.h> #include <linux/mm.h> -#include <linux/init.h> #include <asm/bootinfo.h> #include <loongson.h> +#include <mem.h> void __init prom_init_memory (void ) {add_memory_region (0x0 , (memsize <<20 ),BOOT_MEM_RAM );#ifdef CONFIG_64BIT if (highmemsize >0 ) { -add_memory_region (0x20000000 , +add_memory_region (LOONGSON_HIGHMEM_START , highmemsize <<20 ,BOOT_MEM_RAM ); }#endif /* CONFIG_64BIT */
@@ -34,6 +34,7 @@ int __uncached_access(struct file *file, unsigned long addr)* On the Lemote Loongson 2e system, the peripheral registers * reside between 0x1000:0000 and 0x2000:0000. */ -return addr >=__pa (high_memory) || - ((addr >=0x10000000 ) && (addr <0x20000000 )); +return addr >=__pa (high_memory) || \ + ((addr >=LOONGSON_MMIO_MEM_START ) && \ + (addr <LOONGSON_MMIO_MEM_END )); }
arch/mips/loongson/fuloong-2e/misc.c +3 -1
@@ -7,7 +7,9 @@* option) any later version. */ +#include <machine.h> +const char *get_system_type (void ) { -return "fuloong-2e" ; +return MACH_NAME ; }
arch/mips/loongson/fuloong-2e/pci.c +24 -12
@@ -55,25 +55,37 @@ static struct pci_controller loongson_pci_controller = {static void __init ict_pcimap (void ) {/* -* local to PCI mapping: [256M,512M] -> [256M,512M]; differ from PMON +* local to PCI mapping for CPU accessing PCI space * * CPU address space [256M,448M] is window for accessing pci space -* we set pcimap_lo[0,1,2] to map it to pci space [256M,448M] -* pcimap: bit18,pcimap_2; bit[17-12],lo2;bit[11-6],lo1;bit[5-0],lo0 +* we set pcimap_lo[0,1,2] to map it to pci space[0M, 64M], [320M,448M] +* +* pcimap: PCI_MAP2 PCI_Mem_Lo2 PCI_Mem_Lo1 PCI_Mem_Lo0 +* [<2G] [384M,448M] [320M,384M] [0M,64M] */ -/* 1,00 0110 ,0001 01,00 0000 */ -LOONGSON_PCIMAP =0x46140 ; - -/* 1, 00 0010, 0000,01, 00 0000 */ -/* LOONGSON_PCIMAP = 0x42040; */ +LOONGSON_PCIMAP =LOONGSON_PCIMAP_PCIMAP_2 | +LOONGSON_PCIMAP_WIN (2 ,0x18000000 ) | +LOONGSON_PCIMAP_WIN (1 ,0x14000000 ) | +LOONGSON_PCIMAP_WIN (0 ,0 );/* -* PCI to local mapping: [2G,2G+256M] -> [0,256M] +* PCI-DMA to local mapping: [2G,2G+256M] -> [0M,256M] */ -LOONGSON_PCIBASE0 =0x80000000 ; -LOONGSON_PCIBASE1 =0x00800000 ; -LOONGSON_PCIBASE2 =0x90000000 ; +LOONGSON_PCIBASE0 =0x80000000ul ;/* base: 2G -> mmap: 0M */ +/* size: 256M, burst transmission, pre-fetch enable, 64bit */ +LOONGSON_PCI_HIT0_SEL_L =0xc000000cul ; +LOONGSON_PCI_HIT0_SEL_H =0xfffffffful ; +LOONGSON_PCI_HIT1_SEL_L =0x00000006ul ;/* set this BAR as invalid */ +LOONGSON_PCI_HIT1_SEL_H =0x00000000ul ; +LOONGSON_PCI_HIT2_SEL_L =0x00000006ul ;/* set this BAR as invalid */ +LOONGSON_PCI_HIT2_SEL_H =0x00000000ul ; + +/* avoid deadlock of PCI reading/writing lock operation */ +LOONGSON_PCI_ISR4C =0xd2000001ul ; +/* can not change gnt to break pci transfer when device's gnt not +deassert for some broken device */ +LOONGSON_PXARB_CFG =0x00fe0105ul ; }static int __init pcibios_init (void )
arch/mips/loongson/fuloong-2e/reset.c +11 -8
@@ -6,21 +6,24 @@* * Copyright (C) 2007 Lemote, Inc. & Institute of Computing Technology * Author: Fuxin Zhang, [email protected] +* +* Copyright (c) 2009 Philippe Vachon <[email protected]> +* +* Copyright (c) 2009 Lemote, Inc. & Institute of Computing Technology +* Author: Wu Zhangjin, [email protected] */ #include <linux/pm.h> #include <asm/reboot.h> +#include <loongson.h> static void loongson_restart (char *command) { -#ifdef CONFIG_32BIT - *(unsigned long *)0xbfe00104 &= ~(1 <<2 ); - *(unsigned long *)0xbfe00104 |= (1 <<2 ); -#else - *(unsigned long *)0xffffffffbfe00104 &= ~(1 <<2 ); - *(unsigned long *)0xffffffffbfe00104 |= (1 <<2 ); -#endif - __asm__ __volatile__("jr\t%0" : :"r" (0xbfc00000 )); +LOONGSON_GENCFG &= ~LOONGSON_GENCFG_CPUSELFRESET ; +LOONGSON_GENCFG |=LOONGSON_GENCFG_CPUSELFRESET ; + +/* reboot via jumping to 0xbfc00000 */ + ((void (*)(void ))ioremap_nocache (LOONGSON_BOOT_BASE ,4 )) (); }static void loongson_halt (void )
arch/mips/loongson/fuloong-2e/setup.c +4 -1
@@ -27,7 +27,10 @@ static void loongson_wbflush(void) asm(".set\tpush\n\t" ".set\tnoreorder\n\t" ".set mips3\n\t" -"sync\n\t" "nop\n\t" ".set\tpop\n\t" ".set mips0\n\t" ); +"sync\n\t" +"nop\n\t" +".set\tpop\n\t" +".set mips0\n\t" ); }void __init loongson_wbflush_setup (void )
Signature · 1 line
1.6.2.1
PATCH 8/27 clean up the early printk support for fuloong(2e)
In reply to [email protected]From: Wu Zhangjin <[email protected]>
this is originally from the lm2e-fixes branch of Philippe'sgit://git.linux-cisco.org/linux-mips.git
--- arch/mips/loongson/fuloong-2e/Makefile | 7 +- arch/mips/loongson/fuloong-2e/dbg_io.c | 151 -------------------------- arch/mips/loongson/fuloong-2e/early_printk.c | 28 +++++ 3 files changed, 34 insertions(+), 152 deletions(-) delete mode 100644 arch/mips/loongson/fuloong-2e/dbg_io.c create mode 100644 arch/mips/loongson/fuloong-2e/early_printk.c
arch/mips/loongson/fuloong-2e/Makefile +6 -1
@@ -3,6 +3,11 @@ # obj-y += setup.o init.o cmdline.o time.o reset.o irq.o \ - pci.o bonito-irq.o dbg_io.o mem.o misc.o + pci.o bonito-irq.o mem.o misc.o + +# +# Early printk support +# +obj-$(CONFIG_EARLY_PRINTK) += early_printk.o EXTRA_CFLAGS += -Werror
arch/mips/loongson/fuloong-2e/dbg_io.c deleted +0 -151
151 lines not on this page · raw message
arch/mips/loongson/fuloong-2e/early_printk.c new file +28 -0
@@ -0,0 +1,28 @@ +/* early printk support +* +* Copyright (c) 2009 Philippe Vachon <[email protected]> +* +* This program is free software; you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the +* Free Software Foundation; either version 2 of the License, or (at your +* option) any later version. +*/ + +#include <linux/types.h> +#include <linux/serial_reg.h> + +#include <loongson.h> +#include <machine.h> + +void prom_putchar (char c) +{ +int timeout; +phys_addr_t uart_base = + (phys_addr_t )ioremap_nocache (LOONGSON_UART_BASE ,8 ); +char reg =readb ((u8 *) (uart_base +UART_LSR )) &UART_LSR_THRE ; + +for (timeout =1024 ; reg ==0 && timeout >0 ; timeout--) + reg =readb ((u8 *) (uart_base +UART_LSR )) &UART_LSR_THRE ; + +writeb (c, (u8 *) (uart_base +UART_TX )); +}
Signature · 1 line
1.6.2.1
PATCH 9/27 enable Real Time Clock Support for fuloong(2e)
In reply to [email protected]From: Wu Zhangjin <[email protected]>
by default, RTC_LIB is selected by MIPS, but if RTC_LIB is enabled, Enhanced Real Time Clock Support(RTC) will be disabled, so, to enable it, not select RTC_LIB in LEMOTE_FULOONG2E will fix this problem.
RTC support is needed by some tools like hwclock, if you want hwclock work well, these two jobs need to do:
kernel configuration:
Device Drivers --->
Character devices --->
<*> Enhanced Real Time Clock Support (legacy PC RTC driver)
user-space configuration:
$ mknod /dev/rtc c 10 135
and there is another RTC support in linux, whose kernel option is RTC_CLASS, it should be fixed for fuloong(2e) via enabling the binary mode in driver/rtc/rtc-cmos.c and register the RTC device resource in a machine specific rtc.c
to make hwclock work with it normally, please do:
kernel configuration:
Device Drivers --->
<*> Real Time Clock --->
<*> PC-style 'CMOS'
user-space configuration:
$ mknod /dev/rtc0 c 254 0
/dev/rtc0 is the default RTC device file.
--- arch/mips/Kconfig | 2 +- arch/mips/loongson/fuloong-2e/Makefile | 7 ++++ arch/mips/loongson/fuloong-2e/rtc.c | 55 ++++++++++++++++++++++++++++++++ drivers/rtc/rtc-cmos.c | 8 ++-- 4 files changed, 67 insertions(+), 5 deletions(-) create mode 100644 arch/mips/loongson/fuloong-2e/rtc.c
arch/mips/Kconfig +1 -1
@@ -6,7 +6,7 @@ config MIPS select HAVE_ARCH_KGDB # Horrible source of confusion. Die, die, die ... select EMBEDDED - select RTC_LIB + select RTC_LIB if !LEMOTE_FULOONG2E mainmenu "Linux/MIPS Kernel Configuration"
arch/mips/loongson/fuloong-2e/Makefile +7 -0
@@ -10,4 +10,11 @@ obj-y += setup.o init.o cmdline.o time.o reset.o irq.o \ # obj-$(CONFIG_EARLY_PRINTK) += early_printk.o +# +# Enable RTC Class support +# +# please enable CONFIG_RTC_DRV_CMOS +# +obj-$(CONFIG_RTC_DRV_CMOS) += rtc.o + EXTRA_CFLAGS += -Werror
arch/mips/loongson/fuloong-2e/rtc.c new file +55 -0
55 lines not on this page · raw message
drivers/rtc/rtc-cmos.c +4 -4
@@ -691,7 +691,8 @@ cmos_do_probe(struct device *dev, struct resource *ports, int rtc_irq)*/ #if defined(CONFIG_ATARI ) address_space =64 ; -#elif defined(__i386__) || defined(__x86_64__) || defined(__arm__) || defined(__sparc__) +#elif defined(__i386__) || defined(__x86_64__) || defined(__arm__) \ + || defined(__sparc__) || defined(__mips__) address_space =128 ;#else #warning Assuming 128 bytes of RTC+NVRAM address space, not 64 bytes.
@@ -756,9 +757,8 @@ cmos_do_probe(struct device *dev, struct resource *ports, int rtc_irq)/* FIXME teach the alarm code how to handle binary mode; * <asm-generic/rtc.h> doesn't know 12-hour mode either. */ -if (is_valid_irq (rtc_irq) && - (!(rtc_control &RTC_24H ) || (rtc_control & (RTC_DM_BINARY )))) { -dev_dbg (dev,"only 24-hr BCD mode supported\n" ); +if (is_valid_irq (rtc_irq) && !(rtc_control &RTC_24H )) { +dev_dbg (dev,"only 24-hr supported\n" ); retval = -ENXIO ; goto cleanup1; }
Signature · 1 line
1.6.2.1
PATCH 10/27 add loongson-specific cpu-feature-overrides.h
In reply to [email protected]From: Wu Zhangjin <[email protected]>
This file will obviously reduce the size of kernel image file, reduce tons of branches and enhance the performance.
$ wc -c vmlinux // before 8054849 vmlinux $ wc -c vmlinux // after 7626936 vmlinux $ echo $(((8054849-7626936)/1024)) // kb 417 $ echo "(8054849-7626936)/8054849" | bc -l .05312489408553779220
--- .../asm/mach-loongson/cpu-feature-overrides.h | 58 ++++++++++++++++++++ 1 files changed, 58 insertions(+), 0 deletions(-) create mode 100644 arch/mips/include/asm/mach-loongson/cpu-feature-overrides.h
arch/mips/include/asm/mach-loongson/cpu-feature-overrides.h new file +58 -0
@@ -0,0 +1,58 @@ +/* +* This file is subject to the terms and conditions of the GNU General Public +* License. See the file "COPYING" in the main directory of this archive +* for more details. +* +* Copyright (C) 2009 Wu Zhangjin <[email protected]> +* Copyright (C) 2009 Philippe Vachon <[email protected]> +* Copyright (C) 2009 Zhang Le <[email protected]> +* +* reference: /proc/cpuinfo, +* arch/mips/kernel/cpu-probe.c(cpu_probe_legacy), +* arch/mips/kernel/proc.c(show_cpuinfo), +* loongson2f user manual. +*/ + +#ifndef __ASM_LOONGSON_CPU_FEATURE_OVERRIDES_H +#define __ASM_LOONGSON_CPU_FEATURE_OVERRIDES_H + +#define cpu_dcache_line_size () 32 +#define cpu_icache_line_size () 32 +#define cpu_scache_line_size () 32 + +#define cpu_has_32fpr 1 +#define cpu_has_3k_cache 0 +#define cpu_has_4k_cache 1 +#define cpu_has_4kex 1 +#define cpu_has_64bits 1 +#define cpu_has_cache_cdex_p 0 +#define cpu_has_cache_cdex_s 0 +#define cpu_has_counter 1 +#define cpu_has_dc_aliases 1 +#define cpu_has_divec 0 +#define cpu_has_dsp 0 +#define cpu_has_ejtag 0 +#define cpu_has_fpu 1 +#define cpu_has_ic_fills_f_dc 0 +#define cpu_has_inclusive_pcaches 1 +#define cpu_has_llsc 1 +#define cpu_has_mcheck 0 +#define cpu_has_mdmx 0 +#define cpu_has_mips16 0 +#define cpu_has_mips32r1 0 +#define cpu_has_mips32r2 0 +#define cpu_has_mips3d 0 +#define cpu_has_mips64r1 0 +#define cpu_has_mips64r2 0 +#define cpu_has_mipsmt 0 +#define cpu_has_prefetch 0 +#define cpu_has_smartmips 0 +#define cpu_has_tlb 1 +#define cpu_has_tx39_cache 0 +#define cpu_has_userlocal 0 +#define cpu_has_vce 0 +#define cpu_has_vtag_icache 0 +#define cpu_has_watch 1 +#define cpu_icache_snoops_remote_store 1 + +#endif /* __ASM_LOONGSON_CPU_FEATURE_OVERRIDES_H */
Signature · 1 line
1.6.2.1
PATCH 11/27 split the loongson-specific part out
In reply to [email protected]From: Wu Zhangjin <[email protected]>
for sharing lots of loongson-specific source code among loongson-based machines, there is a need to split the loongson-specific part out to a common/ directory.
and the machine-specific files are put in the machine-name/ directory.
--- arch/mips/Kconfig | 54 +++++------- arch/mips/Makefile | 5 +- arch/mips/include/asm/mach-loongson/loongson.h | 14 +++- arch/mips/loongson/Kconfig | 31 +++++++ arch/mips/loongson/Makefile | 11 +++ arch/mips/loongson/common/Makefile | 20 +++++ arch/mips/loongson/common/bonito-irq.c | 69 +++++++++++++++ arch/mips/loongson/common/cmdline.c | 80 +++++++++++++++++ arch/mips/loongson/common/early_printk.c | 28 ++++++ arch/mips/loongson/common/init.c | 40 +++++++++ arch/mips/loongson/common/irq.c | 110 ++++++++++++++++++++++++ arch/mips/loongson/common/mem.c | 40 +++++++++ arch/mips/loongson/common/misc.c | 15 +++ arch/mips/loongson/common/pci.c | 101 ++++++++++++++++++++++ arch/mips/loongson/common/reset.c | 38 ++++++++ arch/mips/loongson/common/rtc.c | 54 ++++++++++++ arch/mips/loongson/common/setup.c | 74 ++++++++++++++++ arch/mips/loongson/common/time.c | 27 ++++++ arch/mips/loongson/fuloong-2e/Makefile | 17 +--- arch/mips/loongson/fuloong-2e/bonito-irq.c | 69 --------------- arch/mips/loongson/fuloong-2e/cmdline.c | 77 ----------------- arch/mips/loongson/fuloong-2e/early_printk.c | 28 ------ arch/mips/loongson/fuloong-2e/init.c | 40 --------- arch/mips/loongson/fuloong-2e/irq.c | 89 +------------------ arch/mips/loongson/fuloong-2e/mem.c | 40 --------- arch/mips/loongson/fuloong-2e/misc.c | 15 --- arch/mips/loongson/fuloong-2e/pci.c | 102 ---------------------- arch/mips/loongson/fuloong-2e/reset.c | 36 +++------ arch/mips/loongson/fuloong-2e/rtc.c | 55 ------------ arch/mips/loongson/fuloong-2e/setup.c | 74 ---------------- arch/mips/loongson/fuloong-2e/time.c | 27 ------ 31 files changed, 793 insertions(+), 687 deletions(-) create mode 100644 arch/mips/loongson/Kconfig create mode 100644 arch/mips/loongson/Makefile create mode 100644 arch/mips/loongson/common/Makefile create mode 100644 arch/mips/loongson/common/bonito-irq.c create mode 100644 arch/mips/loongson/common/cmdline.c create mode 100644 arch/mips/loongson/common/early_printk.c create mode 100644 arch/mips/loongson/common/init.c create mode 100644 arch/mips/loongson/common/irq.c create mode 100644 arch/mips/loongson/common/mem.c create mode 100644 arch/mips/loongson/common/misc.c create mode 100644 arch/mips/loongson/common/pci.c create mode 100644 arch/mips/loongson/common/reset.c create mode 100644 arch/mips/loongson/common/rtc.c create mode 100644 arch/mips/loongson/common/setup.c create mode 100644 arch/mips/loongson/common/time.c delete mode 100644 arch/mips/loongson/fuloong-2e/bonito-irq.c delete mode 100644 arch/mips/loongson/fuloong-2e/cmdline.c delete mode 100644 arch/mips/loongson/fuloong-2e/early_printk.c delete mode 100644 arch/mips/loongson/fuloong-2e/init.c delete mode 100644 arch/mips/loongson/fuloong-2e/mem.c delete mode 100644 arch/mips/loongson/fuloong-2e/misc.c delete mode 100644 arch/mips/loongson/fuloong-2e/pci.c delete mode 100644 arch/mips/loongson/fuloong-2e/rtc.c delete mode 100644 arch/mips/loongson/fuloong-2e/setup.c delete mode 100644 arch/mips/loongson/fuloong-2e/time.c
arch/mips/Kconfig +22 -32
@@ -6,7 +6,7 @@ config MIPS select HAVE_ARCH_KGDB # Horrible source of confusion. Die, die, die ... select EMBEDDED - select RTC_LIB if !LEMOTE_FULOONG2E + select RTC_LIB if !LOONGSON_SYSTEMS mainmenu "Linux/MIPS Kernel Configuration"
@@ -156,31 +156,16 @@ config LASAT select SYS_SUPPORTS_LITTLE_ENDIAN select GENERIC_HARDIRQS_NO__DO_IRQ -config LEMOTE_FULOONG2E - bool "Lemote Fuloong(2e) mini-PC" - select ARCH_SPARSEMEM_ENABLE - select CEVT_R4K - select CSRC_R4K - select SYS_HAS_CPU_LOONGSON2 - select DMA_NONCOHERENT - select BOOT_ELF32 - select BOARD_SCACHE - select HAVE_STD_PC_SERIAL_PORT - select HW_HAS_PCI - select I8259 - select ISA - select IRQ_CPU - select SYS_SUPPORTS_32BIT_KERNEL - select SYS_SUPPORTS_64BIT_KERNEL - select SYS_SUPPORTS_LITTLE_ENDIAN - select SYS_SUPPORTS_HIGHMEM - select SYS_HAS_EARLY_PRINTK - select GENERIC_HARDIRQS_NO__DO_IRQ - select GENERIC_ISA_DMA_SUPPORT_BROKEN - select CPU_HAS_WB +config LOONGSON_SYSTEMS + bool "Loongson Based Machines" help - Lemote Fulong mini-PC board based on the Chinese Loongson-2E CPU and - an FPGA northbridge + This enables the support of Loongson based machines. + + Loongson is a family of general-purpose MIPS-compatible CPUs. + developed at Institute of Computing Technology (ICT), + Chinese Academy of Sciences (CAS) in the People's Republic + of China. The chief architect is Professor Weiwu Hu. + config MIPS_MALTA bool "MIPS Malta board"
@@ -649,6 +634,7 @@ source "arch/mips/sibyte/Kconfig" source "arch/mips/txx9/Kconfig" source "arch/mips/vr41xx/Kconfig" source "arch/mips/cavium-octeon/Kconfig" +source "arch/mips/loongson/Kconfig" endmenu
@@ -1014,12 +1000,10 @@ choice prompt "CPU type" default CPU_R4X00 -config CPU_LOONGSON2 - bool "Loongson 2" - depends on SYS_HAS_CPU_LOONGSON2 - select CPU_SUPPORTS_32BIT_KERNEL - select CPU_SUPPORTS_64BIT_KERNEL - select CPU_SUPPORTS_HIGHMEM +config CPU_LOONGSON2E + bool "Loongson 2E" + depends on SYS_HAS_CPU_LOONGSON2E + select CPU_LOONGSON2 help The Loongson 2E processor implements the MIPS III instruction set with many extensions.
@@ -1262,7 +1246,13 @@ config CPU_CAVIUM_OCTEON endchoice -config SYS_HAS_CPU_LOONGSON2 +config CPU_LOONGSON2 + bool + select CPU_SUPPORTS_32BIT_KERNEL + select CPU_SUPPORTS_64BIT_KERNEL + select CPU_SUPPORTS_HIGHMEM + +config SYS_HAS_CPU_LOONGSON2E bool config SYS_HAS_CPU_MIPS32_R1
arch/mips/Makefile +3 -2
@@ -306,9 +306,10 @@ load-$(CONFIG_WR_PPMC) += 0xffffffff80100000 # # lemote fulong mini-PC board # -core-$(CONFIG_LEMOTE_FULOONG2E) +=arch/mips/loongson/fuloong-2e/ +core-$(CONFIG_LOONGSON_SYSTEMS) +=arch/mips/loongson/ +cflags-$(CONFIG_LOONGSON_SYSTEMS) += -I$(srctree)/arch/mips/include/asm/mach-loongson \ + -mno-branch-likely load-$(CONFIG_LEMOTE_FULOONG2E) +=0xffffffff80100000 -cflags-$(CONFIG_LEMOTE_FULOONG2E) += -I$(srctree)/arch/mips/include/asm/mach-loongson # # MIPS Malta board
arch/mips/include/asm/mach-loongson/loongson.h +13 -1
@@ -20,7 +20,7 @@/* loongson internal northbridge initialization */ extern void bonito_irq_init (void ); -/* command line */ +/* command line arguments */ extern unsigned long bus_clock, cpu_clock_freq;extern unsigned long memsize, highmemsize;
@@ -31,6 +31,18 @@ extern void loongson_reboot_setup(void);extern void __init prom_init_memory (void );extern void __init prom_init_cmdline (void ); +/* irq operation functions */ +extern void bonito_irqdispatch (void ); +extern void i8259_irqdispatch (void ); +extern void __init bonito_irq_init (void ); +extern void __init set_irq_trigger_mode (void ); +extern inline int mach_i8259_irq (void ); +extern inline void mach_irq_dispatch (unsigned int pending); + +/* machine-specific reboot/halt operation */ +extern void mach_prepare_reboot (void ); +extern void mach_prepare_shutdown (void ); +#define LOONGSON_REG (x) \ (*(u32 *)((char *)CKSEG1ADDR(LOONGSON_REG_BASE) + (x)))#define LOONGSON_IRQ_BASE 32
arch/mips/loongson/Kconfig new file +31 -0
@@ -0,0 +1,31 @@ +choice + prompt "Machine Type" + depends on LOONGSON_SYSTEMS + +config LEMOTE_FULOONG2E + bool "Lemote Fuloong(2e) mini-PC" + select ARCH_SPARSEMEM_ENABLE + select CEVT_R4K + select CSRC_R4K + select SYS_HAS_CPU_LOONGSON2E + select DMA_NONCOHERENT + select BOOT_ELF32 + select BOARD_SCACHE + select HAVE_STD_PC_SERIAL_PORT + select HW_HAS_PCI + select I8259 + select ISA + select IRQ_CPU + select SYS_SUPPORTS_32BIT_KERNEL + select SYS_SUPPORTS_64BIT_KERNEL + select SYS_SUPPORTS_LITTLE_ENDIAN + select SYS_SUPPORTS_HIGHMEM + select SYS_HAS_EARLY_PRINTK + select GENERIC_HARDIRQS_NO__DO_IRQ + select GENERIC_ISA_DMA_SUPPORT_BROKEN + select CPU_HAS_WB + help + Lemote Fulong mini-PC board based on the Chinese Loongson-2E CPU and + an FPGA northbridge + +endchoice
arch/mips/loongson/Makefile new file +11 -0
@@ -0,0 +1,11 @@ +# +# Common code for all Loongson based systems +# + +obj-$(CONFIG_LOONGSON_SYSTEMS) += common/ + +# +# Lemote Fuloong mini-PC (Loongson 2E-based) +# + +obj-$(CONFIG_LEMOTE_FULOONG2E) += fuloong-2e/
arch/mips/loongson/common/Makefile new file +20 -0
@@ -0,0 +1,20 @@ +# +# Makefile for loongson based machines. +# + +obj-y += setup.o init.o cmdline.o time.o reset.o irq.o \ + pci.o bonito-irq.o mem.o misc.o + +# +# Early printk support +# +obj-$(CONFIG_EARLY_PRINTK) += early_printk.o + +# +# Enable RTC Class support +# +# please enable CONFIG_RTC_DRV_CMOS +# +obj-$(CONFIG_RTC_DRV_CMOS) += rtc.o + +EXTRA_CFLAGS += -Werror
arch/mips/loongson/common/bonito-irq.c new file +69 -0
69 lines not on this page · raw message
arch/mips/loongson/common/cmdline.c new file +80 -0
80 lines not on this page · raw message
arch/mips/loongson/common/early_printk.c new file +28 -0
@@ -0,0 +1,28 @@ +/* early printk support +* +* Copyright (c) 2009 Philippe Vachon <[email protected]> +* +* This program is free software; you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the +* Free Software Foundation; either version 2 of the License, or (at your +* option) any later version. +*/ + +#include <linux/types.h> +#include <linux/serial_reg.h> + +#include <loongson.h> +#include <machine.h> + +void prom_putchar (char c) +{ +int timeout; +phys_addr_t uart_base = + (phys_addr_t )ioremap_nocache (LOONGSON_UART_BASE ,8 ); +char reg =readb ((u8 *) (uart_base +UART_LSR )) &UART_LSR_THRE ; + +for (timeout =1024 ; reg ==0 && timeout >0 ; timeout--) + reg =readb ((u8 *) (uart_base +UART_LSR )) &UART_LSR_THRE ; + +writeb (c, (u8 *) (uart_base +UART_TX )); +}
arch/mips/loongson/common/init.c new file +40 -0
@@ -0,0 +1,40 @@ +/* +* Based on Ocelot Linux port, which is +* Copyright 2001 MontaVista Software Inc. +* Author: [email protected] or [email protected] +* +* Copyright 2003 ICT CAS +* Author: Michael Guo <[email protected]> +* +* Copyright (C) 2007 Lemote Inc. & Insititute of Computing Technology +* Author: Fuxin Zhang, [email protected] +* +* This program is free software; you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the +* Free Software Foundation; either version 2 of the License, or (at your +* option) any later version. +*/ + +#include <linux/bootmem.h> + +#include <asm/bootinfo.h> +#include <asm/cpu.h> + +#include <loongson.h> + +void __init prom_init (void ) +{ +/* init mach type, does we need to init it?? */ + mips_machtype =PRID_IMP_LOONGSON2 ; + +/* init several base address */ +set_io_port_base ((unsigned long ) +ioremap (LOONGSON_PCIIO_BASE ,LOONGSON_PCIIO_SIZE )); + +prom_init_cmdline (); +prom_init_memory (); +} + +void __init prom_free_prom_memory (void ) +{ +}
arch/mips/loongson/common/irq.c new file +110 -0
110 lines not on this page · raw message
arch/mips/loongson/common/mem.c new file +40 -0
@@ -0,0 +1,40 @@ +/* +* This program is free software; you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the +* Free Software Foundation; either version 2 of the License, or (at your +* option) any later version. +*/ + +#include <linux/fs.h> +#include <linux/mm.h> + +#include <asm/bootinfo.h> + +#include <loongson.h> +#include <mem.h> + +void __init prom_init_memory (void ) +{ +add_memory_region (0x0 , (memsize <<20 ),BOOT_MEM_RAM ); +#ifdef CONFIG_64BIT +if (highmemsize >0 ) { +add_memory_region (LOONGSON_HIGHMEM_START , + highmemsize <<20 ,BOOT_MEM_RAM ); + } +#endif /* CONFIG_64BIT */ +} + +/* override of arch/mips/mm/cache.c: __uncached_access */ +int __uncached_access (struct file *file,unsigned long addr) +{ +if (file->f_flags &O_SYNC ) +return 1 ; + +/* +* On the Lemote Loongson 2e system, the peripheral registers +* reside between 0x1000:0000 and 0x2000:0000. +*/ +return addr >=__pa (high_memory) || + ((addr >=LOONGSON_MMIO_MEM_START ) && \ + (addr <LOONGSON_MMIO_MEM_END )); +}
arch/mips/loongson/common/misc.c new file +15 -0
@@ -0,0 +1,15 @@ +/* Copyright (C) 2009 Lemote Inc. & Insititute of Computing Technology +* Author: Wu Zhangjin, [email protected] +* +* This program is free software; you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the +* Free Software Foundation; either version 2 of the License, or (at your +* option) any later version. +*/ + +#include <machine.h> + +const char *get_system_type (void ) +{ +return MACH_NAME ; +}
arch/mips/loongson/common/pci.c new file +101 -0
101 lines not on this page · raw message
arch/mips/loongson/common/reset.c new file +38 -0
@@ -0,0 +1,38 @@ +/* +* This program is free software; you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the +* Free Software Foundation; either version 2 of the License, or (at your +* option) any later version. +* +* Copyright (C) 2007 Lemote, Inc. & Institute of Computing Technology +* Author: Fuxin Zhang, [email protected] +*/ + +#include <linux/pm.h> + +#include <asm/reboot.h> + +#include <loongson.h> + +static void loongson_restart (char *command) +{ +/* perform board-specific pre-reboot operations */ +mach_prepare_reboot (); + +/* reboot via jumping to 0xbfc00000 */ + ((void (*)(void ))ioremap_nocache (LOONGSON_BOOT_BASE ,4 )) (); +} + +static void loongson_halt (void ) +{ +mach_prepare_shutdown (); +while (1 ) + ; +} + +void __init loongson_reboot_setup (void ) +{ + _machine_restart = loongson_restart; + _machine_halt = loongson_halt; + pm_power_off = loongson_halt; +}
arch/mips/loongson/common/rtc.c new file +54 -0
54 lines not on this page · raw message
arch/mips/loongson/common/setup.c new file +74 -0
74 lines not on this page · raw message
arch/mips/loongson/common/time.c new file +27 -0
@@ -0,0 +1,27 @@ +/* +* board dependent boot routines +* +* Copyright (C) 2007 Lemote Inc. & Insititute of Computing Technology +* Author: Fuxin Zhang, [email protected] +* +* This program is free software; you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the +* Free Software Foundation; either version 2 of the License, or (at your +* option) any later version. +*/ + +#include <asm/mc146818-time.h> +#include <asm/time.h> + +#include <loongson.h> + +unsigned long read_persistent_clock (void ) +{ +return mc146818_get_cmos_time (); +} + +void __init plat_time_init (void ) +{ +/* setup mips r4k timer */ + mips_hpt_frequency = cpu_clock_freq /2 ; +}
arch/mips/loongson/fuloong-2e/Makefile +2 -15
@@ -1,20 +1,7 @@ # -# Makefile for Lemote Fulong mini-PC board. +# Makefile for fuloong-2e # -obj-y += setup.o init.o cmdline.o time.o reset.o irq.o \ - pci.o bonito-irq.o mem.o misc.o - -# -# Early printk support -# -obj-$(CONFIG_EARLY_PRINTK) += early_printk.o - -# -# Enable RTC Class support -# -# please enable CONFIG_RTC_DRV_CMOS -# -obj-$(CONFIG_RTC_DRV_CMOS) += rtc.o +obj-y += irq.o reset.o EXTRA_CFLAGS += -Werror
arch/mips/loongson/fuloong-2e/bonito-irq.c deleted +0 -69
69 lines not on this page · raw message
arch/mips/loongson/fuloong-2e/cmdline.c deleted +0 -77
77 lines not on this page · raw message
arch/mips/loongson/fuloong-2e/early_printk.c deleted +0 -28
@@ -1,28 +0,0 @@ -/* early printk support -* -* Copyright (c) 2009 Philippe Vachon <[email protected]> -* -* This program is free software; you can redistribute it and/or modify it -* under the terms of the GNU General Public License as published by the -* Free Software Foundation; either version 2 of the License, or (at your -* option) any later version. -*/ - -#include <linux/types.h> -#include <linux/serial_reg.h> - -#include <loongson.h> -#include <machine.h> - -void prom_putchar (char c) -{ -int timeout; -phys_addr_t uart_base = - (phys_addr_t )ioremap_nocache (LOONGSON_UART_BASE ,8 ); -char reg =readb ((u8 *) (uart_base +UART_LSR )) &UART_LSR_THRE ; - -for (timeout =1024 ; reg ==0 && timeout >0 ; timeout--) - reg =readb ((u8 *) (uart_base +UART_LSR )) &UART_LSR_THRE ; - -writeb (c, (u8 *) (uart_base +UART_TX )); -}
arch/mips/loongson/fuloong-2e/init.c deleted +0 -40
@@ -1,40 +0,0 @@ -/* -* Based on Ocelot Linux port, which is -* Copyright 2001 MontaVista Software Inc. -* Author: [email protected] or [email protected] -* -* Copyright 2003 ICT CAS -* Author: Michael Guo <[email protected]> -* -* Copyright (C) 2007 Lemote Inc. & Insititute of Computing Technology -* Author: Fuxin Zhang, [email protected] -* -* This program is free software; you can redistribute it and/or modify it -* under the terms of the GNU General Public License as published by the -* Free Software Foundation; either version 2 of the License, or (at your -* option) any later version. -*/ - -#include <linux/bootmem.h> - -#include <asm/bootinfo.h> -#include <asm/cpu.h> - -#include <loongson.h> - -void __init prom_init (void ) -{ -/* init mach type, does we need to init it?? */ - mips_machtype =PRID_IMP_LOONGSON2 ; - -/* init several base address */ -set_io_port_base ((unsigned long ) -ioremap (LOONGSON_PCIIO_BASE ,LOONGSON_PCIIO_SIZE )); - -prom_init_cmdline (); -prom_init_memory (); -} - -void __init prom_free_prom_memory (void ) -{ -}
arch/mips/loongson/fuloong-2e/irq.c +4 -85
114 lines not on this page · raw message
arch/mips/loongson/fuloong-2e/mem.c deleted +0 -40
@@ -1,40 +0,0 @@ -/* -* This program is free software; you can redistribute it and/or modify it -* under the terms of the GNU General Public License as published by the -* Free Software Foundation; either version 2 of the License, or (at your -* option) any later version. -*/ - -#include <linux/fs.h> -#include <linux/mm.h> - -#include <asm/bootinfo.h> - -#include <loongson.h> -#include <mem.h> - -void __init prom_init_memory (void ) -{ -add_memory_region (0x0 , (memsize <<20 ),BOOT_MEM_RAM ); -#ifdef CONFIG_64BIT -if (highmemsize >0 ) { -add_memory_region (LOONGSON_HIGHMEM_START , - highmemsize <<20 ,BOOT_MEM_RAM ); - } -#endif /* CONFIG_64BIT */ -} - -/* override of arch/mips/mm/cache.c: __uncached_access */ -int __uncached_access (struct file *file,unsigned long addr) -{ -if (file->f_flags &O_SYNC ) -return 1 ; - -/* -* On the Lemote Loongson 2e system, the peripheral registers -* reside between 0x1000:0000 and 0x2000:0000. -*/ -return addr >=__pa (high_memory) || \ - ((addr >=LOONGSON_MMIO_MEM_START ) && \ - (addr <LOONGSON_MMIO_MEM_END )); -}
arch/mips/loongson/fuloong-2e/misc.c deleted +0 -15
@@ -1,15 +0,0 @@ -/* Copyright (C) 2009 Lemote Inc. & Insititute of Computing Technology -* Author: Wu Zhangjin, [email protected] -* -* This program is free software; you can redistribute it and/or modify it -* under the terms of the GNU General Public License as published by the -* Free Software Foundation; either version 2 of the License, or (at your -* option) any later version. -*/ - -#include <machine.h> - -const char *get_system_type (void ) -{ -return MACH_NAME ; -}
arch/mips/loongson/fuloong-2e/pci.c deleted +0 -102
102 lines not on this page · raw message
arch/mips/loongson/fuloong-2e/reset.c +11 -25
@@ -1,40 +1,26 @@ -/* +/* Board-specific reboot/shutdown routines +* Copyright (c) 2009 Philippe Vachon <[email protected]> +* +* Copyright (C) 2009 Lemote Inc. & Insititute of Computing Technology +* Author: Wu Zhangjin, [email protected] +* * This program is free software; you can redistribute it and/or modify it * under the terms of the GNU General Public License as published by the * Free Software Foundation; either version 2 of the License, or (at your * option) any later version. -* -* Copyright (C) 2007 Lemote, Inc. & Institute of Computing Technology -* Author: Fuxin Zhang, [email protected] -* -* Copyright (c) 2009 Philippe Vachon <[email protected]> -* -* Copyright (c) 2009 Lemote, Inc. & Institute of Computing Technology -* Author: Wu Zhangjin, [email protected] */ -#include <linux/pm.h> -#include <asm/reboot.h> +#include <linux/delay.h> +#include <linux/types.h> +#include <loongson.h> -static void loongson_restart (char *command) +void mach_prepare_reboot (void ) {LOONGSON_GENCFG &= ~LOONGSON_GENCFG_CPUSELFRESET ;LOONGSON_GENCFG |=LOONGSON_GENCFG_CPUSELFRESET ; - -/* reboot via jumping to 0xbfc00000 */ - ((void (*)(void ))ioremap_nocache (LOONGSON_BOOT_BASE ,4 )) (); -} - -static void loongson_halt (void ) -{ -while (1 ) - ; } -void loongson_reboot_setup (void ) +void mach_prepare_shutdown (void ) { - _machine_restart = loongson_restart; - _machine_halt = loongson_halt; - pm_power_off = loongson_halt; }
arch/mips/loongson/fuloong-2e/rtc.c deleted +0 -55
55 lines not on this page · raw message
arch/mips/loongson/fuloong-2e/setup.c deleted +0 -74
74 lines not on this page · raw message
arch/mips/loongson/fuloong-2e/time.c deleted +0 -27
@@ -1,27 +0,0 @@ -/* -* board dependent boot routines -* -* Copyright (C) 2007 Lemote Inc. & Insititute of Computing Technology -* Author: Fuxin Zhang, [email protected] -* -* This program is free software; you can redistribute it and/or modify it -* under the terms of the GNU General Public License as published by the -* Free Software Foundation; either version 2 of the License, or (at your -* option) any later version. -*/ - -#include <asm/mc146818-time.h> -#include <asm/time.h> - -#include <loongson.h> - -unsigned long read_persistent_clock (void ) -{ -return mc146818_get_cmos_time (); -} - -void __init plat_time_init (void ) -{ -/* setup mips r4k timer */ - mips_hpt_frequency = cpu_clock_freq /2 ; -}
Signature · 1 line
1.6.2.1
PATCH 12/27 add basic loongson-2f support
In reply to [email protected]From: Wu Zhangjin <[email protected]>
Loongson2F has built-in DDR2 and PCIX controller. The PCIX controller have a similar programming interface with FPGA northbridge used in Loongson2E.
so, the main difference between loongson-2e and loongson-2f is:
loongson-2f has an extra address windows configuration module, which can be used to map CPU address space to DDR or PCI address space, or map the PCI-DMA address space to DDR or LIO address space.
herein, the module and the operations are abstracted to loongson.h.
NOTE: this module is only available in 64bit kernel.
--- arch/mips/Kconfig | 18 +++++ .../mips/include/asm/mach-loongson/dma-coherence.h | 4 + arch/mips/include/asm/mach-loongson/loongson.h | 79 +++++++++++++++++++- arch/mips/include/asm/mach-loongson/mem.h | 23 ++++++ arch/mips/include/asm/mach-loongson/pci.h | 30 +++++++- arch/mips/loongson/common/init.c | 17 ++++ arch/mips/loongson/common/mem.c | 21 ++++- arch/mips/loongson/common/pci.c | 14 +++- 8 files changed, 197 insertions(+), 9 deletions(-)
arch/mips/Kconfig +18 -0
@@ -1008,6 +1008,21 @@ config CPU_LOONGSON2E The Loongson 2E processor implements the MIPS III instruction set with many extensions. + It has an internal FPGA northbridge, which is compatiable to + bonito64. + +config CPU_LOONGSON2F + bool "Loongson 2F" + depends on SYS_HAS_CPU_LOONGSON2F + select CPU_LOONGSON2 + help + The Loongson 2F processor implements the MIPS III instruction set + with many extensions. + + Loongson2F have built-in DDR2 and PCIX controller. The PCIX controller + have a similar programming interface with FPGA northbridge used in + Loongson2E. + config CPU_MIPS32_R1 bool "MIPS32 Release 1" depends on SYS_HAS_CPU_MIPS32_R1
@@ -1255,6 +1270,9 @@ config CPU_LOONGSON2 config SYS_HAS_CPU_LOONGSON2E bool +config SYS_HAS_CPU_LOONGSON2F + bool + config SYS_HAS_CPU_MIPS32_R1 bool
arch/mips/include/asm/mach-loongson/dma-coherence.h +4 -0
@@ -27,7 +27,11 @@ static inline dma_addr_t plat_map_dma_mem_page(struct device *dev,static inline unsigned long plat_dma_addr_to_phys (dma_addr_t dma_addr) { +#if defined(CONFIG_CPU_LOONGSON2F ) & defined(CONFIG_64BIT ) +return (dma_addr >0x8fffffff ) ? dma_addr : (dma_addr &0x0fffffff ); +#else return dma_addr &0x7fffffff ; +#endif }static inline void plat_unmap_dma_mem (struct device *dev,dma_addr_t dma_addr)
arch/mips/include/asm/mach-loongson/loongson.h +78 -1
83 lines not on this page · raw message
arch/mips/include/asm/mach-loongson/mem.h +23 -0
@@ -1,8 +1,31 @@#ifndef __MEM_H#define __MEM_H +/* +* high memory space +* +* in loongson2e, starts from 512M +* in loongson2f, starts from 2G + 256M +*/ +#ifdef CONFIG_CPU_LOONGSON2E #define LOONGSON_HIGHMEM_START 0x20000000 +#else +#define LOONGSON_HIGHMEM_START 0x90000000 +#endif + +/* +* the peripheral registers(MMIO): +* +* On the Lemote Loongson 2e system, reside between 0x1000:0000 and 0x2000:0000. +* On the Lemote Loongson 2f system, reside between 0x1000:0000 and 0x8000:0000. +*/ +#define LOONGSON_MMIO_MEM_START 0x10000000 + +#ifdef CONFIG_CPU_LOONGSON2E #define LOONGSON_MMIO_MEM_END 0x20000000 +#else +#define LOONGSON_MMIO_MEM_END 0x80000000 +#endif #endif /* !__MEM_H */
arch/mips/include/asm/mach-loongson/pci.h +29 -1
@@ -1,5 +1,6 @@/* * Copyright (c) 2008 Zhang Le <[email protected]> +* Copyright (c) 2009 Wu Zhangjin <[email protected]> * * This program is free software; you can redistribute it * and/or modify it under the terms of the GNU General
@@ -24,8 +25,35 @@extern struct pci_ops loongson_pci_ops; +/* this is an offset from mips_io_port_base */ +#define LOONGSON_PCI_IO_START 0x00004000UL + +#if defined(CONFIG_CPU_LOONGSON2F ) && defined(CONFIG_64BIT ) + +/* +* we use address window2 to map cpu address space to pci space +* window2: cpu [1G, 2G] -> pci [1G, 2G] +* why not use window 0 & 1? because they are used by cpu when booting. +* window0: cpu [0, 256M] -> ddr [0, 256M] +* window1: cpu [256M, 512M] -> pci [256M, 512M] +*/ + +/* the smallest LOONGSON_CPU_MEM_SRC can be 512M */ +#define LOONGSON_CPU_MEM_SRC 0x40000000ul/* 1G */ +#define LOONGSON_PCI_MEM_DST LOONGSON_CPU_MEM_SRC + +#define LOONGSON_PCI_MEM_START LOONGSON_PCI_MEM_DST +#define LOONGSON_PCI_MEM_END (0x80000000ul-1)/* 2G */ + +#define MMAP_CPUTOPCI_SIZE (LOONGSON_PCI_MEM_END - \ + LOONGSON_PCI_MEM_START + 1) + +#else /* loongson2f/32bit & loongson2e */ +#define LOONGSON_PCI_MEM_START 0x14000000UL#define LOONGSON_PCI_MEM_END 0x1fffffffUL -#define LOONGSON_PCI_IO_START 0x00004000UL + +#endif /* !(defined(CONFIG_CPU_LOONGSON2F) && defined(CONFIG_64BIT))*/ +#endif /* !_LOONGSON_PCI_H_ */
arch/mips/loongson/common/init.c +17 -0
@@ -22,6 +22,17 @@#include <loongson.h> +#if defined(CONFIG_CPU_LOONGSON2F ) && defined(CONFIG_64BIT ) +unsigned long _loongson_addrwincfg_base; + +/* Loongson CPU address windows config space base address */ +static inline void set_loongson_addrwincfg_base (unsigned long base) +{ + *(unsigned long *)&_loongson_addrwincfg_base = base; +barrier (); +} +#endif +void __init prom_init (void ) {/* init mach type, does we need to init it?? */
@@ -31,6 +42,12 @@ void __init prom_init(void)set_io_port_base ((unsigned long )ioremap (LOONGSON_PCIIO_BASE ,LOONGSON_PCIIO_SIZE )); +#if defined(CONFIG_CPU_LOONGSON2F ) && defined(CONFIG_64BIT ) +set_loongson_addrwincfg_base ((unsigned long ) +ioremap (LOONGSON_ADDRWINCFG_BASE , +LOONGSON_ADDRWINCFG_SIZE )); +#endif +prom_init_cmdline ();prom_init_memory (); }
arch/mips/loongson/common/mem.c +17 -4
@@ -17,6 +17,23 @@ void __init prom_init_memory(void) {add_memory_region (0x0 , (memsize <<20 ),BOOT_MEM_RAM );#ifdef CONFIG_64BIT +#ifdef CONFIG_CPU_LOONGSON2F + { +int bit; + + bit =fls (memsize + highmemsize); +if (bit !=ffs (memsize + highmemsize)) + bit +=20 ; +else + bit = bit +20 -1 ; + +/* set cpu window3 to map CPU to DDR: 2G -> 2G */ +LOONGSON_ADDRWIN_CPUTODDR (ADDRWIN_WIN3 ,0x80000000ul , +0x80000000ul , (1 << bit)); +mmiowb (); + } +#endif /* CONFIG_CPU_LOONGSON2F */ +if (highmemsize >0 ) {add_memory_region (LOONGSON_HIGHMEM_START , highmemsize <<20 ,BOOT_MEM_RAM );
@@ -30,10 +47,6 @@ int __uncached_access(struct file *file, unsigned long addr)if (file->f_flags &O_SYNC )return 1 ; -/* -* On the Lemote Loongson 2e system, the peripheral registers -* reside between 0x1000:0000 and 0x2000:0000. -*/ return addr >=__pa (high_memory) || ((addr >=LOONGSON_MMIO_MEM_START ) && \ (addr <LOONGSON_MMIO_MEM_END ));
arch/mips/loongson/common/pci.c +11 -3
@@ -30,15 +30,15 @@#include <pci.h> static struct resource loongson_pci_mem_resource = { - .name ="LOONGSON PCI MEM" , + .name ="pci memory space" , .start =LOONGSON_PCI_MEM_START , .end =LOONGSON_PCI_MEM_END , .flags =IORESOURCE_MEM , };static struct resource loongson_pci_io_resource = { - .name ="LOONGSON PCI IO MEM" , - .start =LOONGSON_PCI_IO_START , + .name ="pci io space" , + .start =LOONGSON_PCI_IO_START ,/* reserve regacy I/O space */ .end =IO_SPACE_LIMIT , .flags =IORESOURCE_IO , };
@@ -85,6 +85,14 @@ static void __init ict_pcimap(void)/* can not change gnt to break pci transfer when device's gnt not deassert for some broken device */ LOONGSON_PXARB_CFG =0x00fe0105ul ; + +#if defined(CONFIG_CPU_LOONGSON2F ) && defined(CONFIG_64BIT ) +/* +* set cpu addr window2 to map CPU address space to PCI address space +*/ +LOONGSON_ADDRWIN_CPUTOPCI (ADDRWIN_WIN2 ,LOONGSON_CPU_MEM_SRC , +LOONGSON_PCI_MEM_DST ,MMAP_CPUTOPCI_SIZE ); +#endif }static int __init pcibios_init (void )
Signature · 1 line
1.6.2.1
PATCH 13/27 add basic fuloong(2f) support
In reply to [email protected]From: Wu Zhangjin <[email protected]>
fuloong(2e) has an VIA686B south bridge, but fuloong(2f) has an AMD CS5536 south bridge. so, we need to add basic cs5536 south bridge support here.
there are several modules provided by cs5536, currently, only these modules are used in fuloong(2f) mini PC: ide, acc(audio), ohci, isa, and ehci. and these modules are general modules, which means should be compiled in kernel by default, besides, there are several selective
modules: flash(nor and nand), otg, udc. the otg and udc modules are used in the NAS machine made by Lemote(the source code support will be added later, only a few differ from fuloong2f mini PC).
since the PCI operations are similiar between fuloong(2e) and fuloong(2f),yeeloong(2f) and even similiar to gdium, herein, I just rename ops-fuloong2e.c to ops-loongsgon2.c to share most of the source code.
PS: the originl cs5536 support for fuloong2f is from the to-mips branch of git://dev.lemote.com/linux_loongson.git, tons of source code have been cleaned up. the most important change is using the linux-internal pci_regs.h(include/linux/pci_regs.h) instead of the original pcireg.h and dividing the huge cs5536_vsm.c to several small files, one file one cs5536 module. at the same time, tons of souce code are tuned to be understandable and some trashy souce code are removed away which will archieve a higher performance. and also, the header files, cs5536.h and cs5536_pci.h are cleaned up a lot.
--- arch/mips/Makefile | 1 + .../mips/include/asm/mach-loongson/cs5536/cs5536.h | 382 +++++++++++++++++ .../include/asm/mach-loongson/cs5536/cs5536_pci.h | 174 ++++++++ .../include/asm/mach-loongson/cs5536/cs5536_vsm.h | 59 +++ arch/mips/include/asm/mach-loongson/loongson.h | 2 +- arch/mips/include/asm/mach-loongson/machine.h | 30 ++ arch/mips/loongson/Kconfig | 44 ++ arch/mips/loongson/Makefile | 6 + arch/mips/loongson/common/Makefile | 6 + arch/mips/loongson/common/bonito-irq.c | 5 + arch/mips/loongson/common/cs5536/Makefile | 20 + arch/mips/loongson/common/cs5536/cs5536_acc.c | 155 +++++++ arch/mips/loongson/common/cs5536/cs5536_ehci.c | 165 +++++++ arch/mips/loongson/common/cs5536/cs5536_flash.c | 450 ++++++++++++++++++++ arch/mips/loongson/common/cs5536/cs5536_ide.c | 193 +++++++++ arch/mips/loongson/common/cs5536/cs5536_isa.c | 376 ++++++++++++++++ arch/mips/loongson/common/cs5536/cs5536_ohci.c | 167 ++++++++ arch/mips/loongson/common/cs5536/cs5536_otg.c | 137 ++++++ arch/mips/loongson/common/cs5536/cs5536_pci.c | 126 ++++++ arch/mips/loongson/common/cs5536/cs5536_udc.c | 142 ++++++ arch/mips/loongson/fuloong-2f/Makefile | 5 + arch/mips/loongson/fuloong-2f/irq.c | 53 +++ arch/mips/loongson/fuloong-2f/reset.c | 65 +++ arch/mips/pci/Makefile | 3 +- arch/mips/pci/fixup-fuloong2f.c | 171 ++++++++ arch/mips/pci/ops-fuloong2e.c | 160 ------- arch/mips/pci/ops-loongson2.c | 213 +++++++++ 27 files changed, 3148 insertions(+), 162 deletions(-) create mode 100644 arch/mips/include/asm/mach-loongson/cs5536/cs5536.h create mode 100644 arch/mips/include/asm/mach-loongson/cs5536/cs5536_pci.h create mode 100644 arch/mips/include/asm/mach-loongson/cs5536/cs5536_vsm.h create mode 100644 arch/mips/loongson/common/cs5536/Makefile create mode 100644 arch/mips/loongson/common/cs5536/cs5536_acc.c create mode 100644 arch/mips/loongson/common/cs5536/cs5536_ehci.c create mode 100644 arch/mips/loongson/common/cs5536/cs5536_flash.c create mode 100644 arch/mips/loongson/common/cs5536/cs5536_ide.c create mode 100644 arch/mips/loongson/common/cs5536/cs5536_isa.c create mode 100644 arch/mips/loongson/common/cs5536/cs5536_ohci.c create mode 100644 arch/mips/loongson/common/cs5536/cs5536_otg.c create mode 100644 arch/mips/loongson/common/cs5536/cs5536_pci.c create mode 100644 arch/mips/loongson/common/cs5536/cs5536_udc.c create mode 100644 arch/mips/loongson/fuloong-2f/Makefile create mode 100644 arch/mips/loongson/fuloong-2f/irq.c create mode 100644 arch/mips/loongson/fuloong-2f/reset.c create mode 100644 arch/mips/pci/fixup-fuloong2f.c delete mode 100644 arch/mips/pci/ops-fuloong2e.c create mode 100644 arch/mips/pci/ops-loongson2.c
arch/mips/Makefile +1 -0
@@ -310,6 +310,7 @@ core-$(CONFIG_LOONGSON_SYSTEMS) +=arch/mips/loongson/ cflags-$(CONFIG_LOONGSON_SYSTEMS) += -I$(srctree)/arch/mips/include/asm/mach-loongson \ -mno-branch-likely load-$(CONFIG_LEMOTE_FULOONG2E) +=0xffffffff80100000 +load-$(CONFIG_LEMOTE_FULOONG2F) +=0xffffffff80200000 # # MIPS Malta board
arch/mips/include/asm/mach-loongson/cs5536/cs5536.h new file +382 -0
382 lines not on this page · raw message
arch/mips/include/asm/mach-loongson/cs5536/cs5536_pci.h new file +174 -0
174 lines not on this page · raw message
arch/mips/include/asm/mach-loongson/cs5536/cs5536_vsm.h new file +59 -0
59 lines not on this page · raw message
arch/mips/include/asm/mach-loongson/loongson.h +1 -1
@@ -287,7 +287,7 @@ extern unsigned long _loongson_addrwincfg_base; s##_WIN##w##_BASE = (src); \ s##_WIN##w##_MMAP = (src) | ADDRWIN_MAP_DST_##d; \ s##_WIN##w##_MASK = ~(size-1); \ -} while (0); +} while (0)#define LOONGSON_ADDRWIN_CPUTOPCI (win, src, dst, size) \ LOONGSON_ADDRWIN_CFG(CPU, PCI, win, src, dst, size)
arch/mips/include/asm/mach-loongson/machine.h +30 -0
@@ -13,6 +13,8 @@#ifndef __MACHINE_H#define __MACHINE_H +#ifdef CONFIG_LEMOTE_FULOONG2E +#define MACH_NAME "lemote-fuloong(2e)"#define LOONGSON_UART_BASE 0x1fd003f8
@@ -23,5 +25,33 @@#define LOONGSON_TIMER_IRQ (MIPS_CPU_IRQ_BASE + 7)#define LOONGSON_DMATIMEOUT_IRQ (LOONGSON_IRQ_BASE + 10) +#else /* CONFIG_LEMOTE_FULOONG2F */ + +#define MACH_NAME "lemote-fuloong(2f)" + +#define LOONGSON_UART_BASE 0x1fd002f8 + +#define LOONGSON_TIMER_IRQ (MIPS_CPU_IRQ_BASE + 7)/* cpu timer */ +#define LOONGSON_PERFCNT_IRQ (MIPS_CPU_IRQ_BASE + 6)/* cpu perf counter */ +#define LOONGSON_NORTH_BRIDGE_IRQ (MIPS_CPU_IRQ_BASE + 6)/* bonito */ +#define LOONGSON_UART_IRQ (MIPS_CPU_IRQ_BASE + 3)/* cpu serial port */ +#define LOONGSON_SOUTH_BRIDGE_IRQ (MIPS_CPU_IRQ_BASE + 2)/* i8259 */ + +#define LOONGSON_INT_BIT_GPIO1 (1 << 1) +#define LOONGSON_INT_BIT_GPIO2 (1 << 2) +#define LOONGSON_INT_BIT_GPIO3 (1 << 3) +#define LOONGSON_INT_BIT_PCI_INTA (1 << 4) +#define LOONGSON_INT_BIT_PCI_INTB (1 << 5) +#define LOONGSON_INT_BIT_PCI_INTC (1 << 6) +#define LOONGSON_INT_BIT_PCI_INTD (1 << 7) +#define LOONGSON_INT_BIT_PCI_PERR (1 << 8) +#define LOONGSON_INT_BIT_PCI_SERR (1 << 9) +#define LOONGSON_INT_BIT_DDR (1 << 10) +#define LOONGSON_INT_BIT_INT0 (1 << 11) +#define LOONGSON_INT_BIT_INT1 (1 << 12) +#define LOONGSON_INT_BIT_INT2 (1 << 13) +#define LOONGSON_INT_BIT_INT3 (1 << 14) + +#endif #endif /* ! __MACHINE_H */
arch/mips/loongson/Kconfig +44 -0
48 lines not on this page · raw message
arch/mips/loongson/Makefile +6 -0
@@ -9,3 +9,9 @@ obj-$(CONFIG_LOONGSON_SYSTEMS) += common/ # obj-$(CONFIG_LEMOTE_FULOONG2E) += fuloong-2e/ + +# +# Lemote Fuloong mini-PC (Loongson 2F-based) +# + +obj-$(CONFIG_LEMOTE_FULOONG2F) += fuloong-2f/
arch/mips/loongson/common/Makefile +6 -0
@@ -17,4 +17,10 @@ obj-$(CONFIG_EARLY_PRINTK) += early_printk.o # obj-$(CONFIG_RTC_DRV_CMOS) += rtc.o +# +# Enable CS5536 Virtual Support Module(VSM) for virtulize the PCI configure +# space +# +obj-$(CONFIG_CS5536) += cs5536/ + EXTRA_CFLAGS += -Werror
arch/mips/loongson/common/bonito-irq.c +5 -0
@@ -53,10 +53,13 @@ static struct irq_chip bonito_irq_type = { .unmask = bonito_irq_enable, }; +/* there is no need to handle dma timeout in loongson-2f based machines */ +#ifdef CONFIG_CPU_LOONGSON2E static struct irqaction dma_timeout_irqaction = { .handler = no_action, .name ="dma_timeout" , }; +#endif void bonito_irq_init (void ) {
@@ -65,5 +68,7 @@ void bonito_irq_init(void)for (i =LOONGSON_IRQ_BASE ; i <LOONGSON_IRQ_BASE +32 ; i++)set_irq_chip_and_handler (i, &bonito_irq_type, handle_level_irq); +#ifdef CONFIG_CPU_LOONGSON2E setup_irq (LOONGSON_DMATIMEOUT_IRQ , &dma_timeout_irqaction); +#endif }
arch/mips/loongson/common/cs5536/Makefile new file +20 -0
@@ -0,0 +1,20 @@ +# +# Makefile for CS5536 support. +# + +# +# core modules +# +obj-$(CONFIG_CS5536) += cs5536_pci.o cs5536_ide.o cs5536_acc.o cs5536_ohci.o \ + cs5536_isa.o cs5536_ehci.o +# +# selective modules +# +# add a CS5536_[MODULE] to your board in arch/mips/loongson/Kconfig +# +obj-$(CONFIG_CS5536_FLASH) += cs5536_flash.o +obj-$(CONFIG_CS5536_NOR_FLASH) += cs5536_flash.o +obj-$(CONFIG_CS5536_OTG) += cs5536_otg.o +obj-$(CONFIG_CS5536_UDC) += cs5536_udc.o + +EXTRA_CFLAGS += -Werror
arch/mips/loongson/common/cs5536/cs5536_acc.c new file +155 -0
155 lines not on this page · raw message
arch/mips/loongson/common/cs5536/cs5536_ehci.c new file +165 -0
165 lines not on this page · raw message
arch/mips/loongson/common/cs5536/cs5536_flash.c new file +450 -0
450 lines not on this page · raw message
arch/mips/loongson/common/cs5536/cs5536_ide.c new file +193 -0
193 lines not on this page · raw message
arch/mips/loongson/common/cs5536/cs5536_isa.c new file +376 -0
376 lines not on this page · raw message
arch/mips/loongson/common/cs5536/cs5536_ohci.c new file +167 -0
167 lines not on this page · raw message
arch/mips/loongson/common/cs5536/cs5536_otg.c new file +137 -0
137 lines not on this page · raw message
arch/mips/loongson/common/cs5536/cs5536_pci.c new file +126 -0
126 lines not on this page · raw message
arch/mips/loongson/common/cs5536/cs5536_udc.c new file +142 -0
142 lines not on this page · raw message
arch/mips/loongson/fuloong-2f/Makefile new file +5 -0
@@ -0,0 +1,5 @@ +# +# Makefile for fuloong-2f +# + +obj-y += irq.o reset.o
arch/mips/loongson/fuloong-2f/irq.c new file +53 -0
53 lines not on this page · raw message
arch/mips/loongson/fuloong-2f/reset.c new file +65 -0
65 lines not on this page · raw message
arch/mips/pci/Makefile +2 -1
@@ -26,7 +26,8 @@ obj-$(CONFIG_MIPS_COBALT) += fixup-cobalt.o obj-$(CONFIG_SOC_AU1500) += fixup-au1000.o ops-au1000.o obj-$(CONFIG_SOC_AU1550) += fixup-au1000.o ops-au1000.o obj-$(CONFIG_SOC_PNX8550) += fixup-pnx8550.o ops-pnx8550.o -obj-$(CONFIG_LEMOTE_FULOONG2E) += fixup-fuloong2e.o ops-fuloong2e.o +obj-$(CONFIG_LEMOTE_FULOONG2E) += fixup-fuloong2e.o ops-loongson2.o +obj-$(CONFIG_LEMOTE_FULOONG2F) += fixup-fuloong2f.o ops-loongson2.o obj-$(CONFIG_MIPS_MALTA) += fixup-malta.o obj-$(CONFIG_PMC_MSP7120_GW) += fixup-pmcmsp.o ops-pmcmsp.o obj-$(CONFIG_PMC_MSP7120_EVAL) += fixup-pmcmsp.o ops-pmcmsp.o
arch/mips/pci/fixup-fuloong2f.c new file +171 -0
171 lines not on this page · raw message
arch/mips/pci/ops-fuloong2e.c deleted +0 -160
8 lines not on this page · raw message
arch/mips/pci/ops-loongson2.c new file +213 -0
213 lines not on this page · raw message
The rest of this diff is not shown. View the raw message.
Signature · 1 line
1.6.2.1
Part of the diff is not shown here. View the raw message.
PATCH 14/27 enable serial port support of loongson-based machines
In reply to [email protected]From: Wu Zhangjin <[email protected]>
this serial port support is portable to loongson-based machines, the old serial port support in fuloong(2e) via HAVE_STD_PC_SERIAL_PORT is replaced by this implementation.
before, only fuloong(2e) used HAVE_STD_PC_SERIAL_PORT kernel option, so, with this new support, we can remove arch/mips/kernel/8250-platform.c directly. but in this patch, that file is reserved there for potential use in the other machines.
--- arch/mips/include/asm/mach-loongson/machine.h | 4 ++ arch/mips/loongson/Kconfig | 1 - arch/mips/loongson/common/Makefile | 5 ++ arch/mips/loongson/common/serial.c | 64 +++++++++++++++++++++++++ 4 files changed, 73 insertions(+), 1 deletions(-) create mode 100644 arch/mips/loongson/common/serial.c
arch/mips/include/asm/mach-loongson/machine.h +4 -0
@@ -18,6 +18,8 @@#define MACH_NAME "lemote-fuloong(2e)"#define LOONGSON_UART_BASE 0x1fd003f8 +#define LOONGSON_UART_BAUD 1843200 +#define LOONGSON_UART_IOTYPE UPIO_PORT#define LOONGSON_NORTH_BRIDGE_IRQ (MIPS_CPU_IRQ_BASE + 2)#define LOONGSON_UART_IRQ (MIPS_CPU_IRQ_BASE + 4)
@@ -30,6 +32,8 @@#define MACH_NAME "lemote-fuloong(2f)"#define LOONGSON_UART_BASE 0x1fd002f8 +#define LOONGSON_UART_BAUD 1843200 +#define LOONGSON_UART_IOTYPE UPIO_PORT#define LOONGSON_TIMER_IRQ (MIPS_CPU_IRQ_BASE + 7)/* cpu timer */ #define LOONGSON_PERFCNT_IRQ (MIPS_CPU_IRQ_BASE + 6)/* cpu perf counter */
arch/mips/loongson/Kconfig +0 -1
@@ -11,7 +11,6 @@ config LEMOTE_FULOONG2E select DMA_NONCOHERENT select BOOT_ELF32 select BOARD_SCACHE - select HAVE_STD_PC_SERIAL_PORT select HW_HAS_PCI select I8259 select ISA
arch/mips/loongson/common/Makefile +5 -0
@@ -23,4 +23,9 @@ obj-$(CONFIG_RTC_DRV_CMOS) += rtc.o # obj-$(CONFIG_CS5536) += cs5536/ +# +# Enable serial port +# +obj-$(CONFIG_SERIAL_8250) += serial.o + EXTRA_CFLAGS += -Werror
arch/mips/loongson/common/serial.c new file +64 -0
64 lines not on this page · raw message
Signature · 1 line
1.6.2.1
PATCH 15/27 add basic yeeloong(2f) laptop support
In reply to [email protected]From: Wu Zhangjin <[email protected]>
yeeloong(2f) laptop is also a Loongson2F-based machine maded by lemote.com.
the board of yeeloong(2f) is similiar to fuloong(2f) mini PC, it has an AMD cs5536 south bridge and has an extra Embedded Controller(EC) for power management, keyboard controlling and some other relative jobs.
so, the difference of the source code of yeeloong(2f) and fuloong(2f) is very small except:
1. the reboot/halt operation is controlled by an Embedded Controller in yeeloong(2f), but in fuloong(2f), by cs5536 directly.
2. there is no serial port device can be used directly in yeeloong(2f), but you can joint one for there is an cpu serial port provided by loongson2f. the address is 0x1ff003f8, you can enable it in kernel via CONFIG_SERIAL_8250.
3. yeeloong(2f) use a SMI video card, the driver source code will be added later.
--- arch/mips/Makefile | 1 + arch/mips/include/asm/mach-loongson/cmdline.h | 9 ++ arch/mips/include/asm/mach-loongson/machine.h | 29 ++++- arch/mips/loongson/Kconfig | 46 +++++++- arch/mips/loongson/Makefile | 6 + arch/mips/loongson/common/cmdline.c | 5 + arch/mips/loongson/yeeloong-2f/Makefile | 5 + arch/mips/loongson/yeeloong-2f/init.c | 71 ++++++++++ arch/mips/loongson/yeeloong-2f/irq.c | 53 ++++++++ arch/mips/loongson/yeeloong-2f/reset.c | 40 ++++++ arch/mips/pci/Makefile | 3 +- arch/mips/pci/fixup-fuloong2f.c | 171 ------------------------- arch/mips/pci/fixup-lemote2f.c | 171 +++++++++++++++++++++++++ 13 files changed, 435 insertions(+), 175 deletions(-) create mode 100644 arch/mips/include/asm/mach-loongson/cmdline.h create mode 100644 arch/mips/loongson/yeeloong-2f/Makefile create mode 100644 arch/mips/loongson/yeeloong-2f/init.c create mode 100644 arch/mips/loongson/yeeloong-2f/irq.c create mode 100644 arch/mips/loongson/yeeloong-2f/reset.c delete mode 100644 arch/mips/pci/fixup-fuloong2f.c create mode 100644 arch/mips/pci/fixup-lemote2f.c
arch/mips/Makefile +1 -0
@@ -311,6 +311,7 @@ cflags-$(CONFIG_LOONGSON_SYSTEMS) += -I$(srctree)/arch/mips/include/asm/mach-loo -mno-branch-likely load-$(CONFIG_LEMOTE_FULOONG2E) +=0xffffffff80100000 load-$(CONFIG_LEMOTE_FULOONG2F) +=0xffffffff80200000 +load-$(CONFIG_LEMOTE_YEELOONG2F) +=0xffffffff80200000 # # MIPS Malta board
arch/mips/include/asm/mach-loongson/cmdline.h new file +9 -0
@@ -0,0 +1,9 @@ +/* machine-specific command line initialization */ +#ifdef CONFIG_SYS_HAS_MACH_PROM_INIT_CMDLINE +extern void __init mach_prom_init_cmdline (void ); +#else +void __init mach_prom_init_cmdline (void ) +{ +} +#endif +
arch/mips/include/asm/mach-loongson/machine.h +28 -1
@@ -27,7 +27,7 @@#define LOONGSON_TIMER_IRQ (MIPS_CPU_IRQ_BASE + 7)#define LOONGSON_DMATIMEOUT_IRQ (LOONGSON_IRQ_BASE + 10) -#else /* CONFIG_LEMOTE_FULOONG2F */ +#elif defined(CONFIG_LEMOTE_FULOONG2F )#define MACH_NAME "lemote-fuloong(2f)"
@@ -35,6 +35,33 @@#define LOONGSON_UART_BAUD 1843200#define LOONGSON_UART_IOTYPE UPIO_PORT +#else /* CONFIG_CPU_YEELOONG2F */ + +#define MACH_NAME "lemote-yeeloong(2f)" + +/* yeeloong use the CPU serial port of Loongson2F */ +#define LOONGSON_UART_BASE 0x1ff003f8 +#define LOONGSON_UART_BAUD 3686400 +#define LOONGSON_UART_IOTYPE UPIO_MEM + +/* +* The following registers are determined by the EC index configuration. +* 1, fill the PORT_HIGH as EC register high part. +* 2, fill the PORT_LOW as EC register low part. +* 3, fill the PORT_DATA as EC register write data or get the data from it. +*/ +#define EC_IO_PORT_HIGH 0x0381 +#define EC_IO_PORT_LOW 0x0382 +#define EC_IO_PORT_DATA 0x0383 +#define REG_RESET_HIGH 0xF4/* reset the machine auto-clear : rd/wr */ +#define REG_RESET_LOW 0xEC +#define BIT_RESET_ON (1 << 0) + +#endif /* !CONFIG_LEMOTE_FULOONG2E */ + +/* fuloong2f and yeeloong2f have the same IRQ control interface */ +#if defined(CONFIG_LEMOTE_FULOONG2F ) || defined(CONFIG_LEMOTE_YEELOONG2F ) +#define LOONGSON_TIMER_IRQ (MIPS_CPU_IRQ_BASE + 7)/* cpu timer */ #define LOONGSON_PERFCNT_IRQ (MIPS_CPU_IRQ_BASE + 6)/* cpu perf counter */ #define LOONGSON_NORTH_BRIDGE_IRQ (MIPS_CPU_IRQ_BASE + 6)/* bonito */
arch/mips/loongson/Kconfig +44 -2
63 lines not on this page · raw message
arch/mips/loongson/Makefile +6 -0
@@ -15,3 +15,9 @@ obj-$(CONFIG_LEMOTE_FULOONG2E) += fuloong-2e/ # obj-$(CONFIG_LEMOTE_FULOONG2F) += fuloong-2f/ + +# +# Lemote Yeeloong mini-PC (Loongson 2F-based) +# + +obj-$(CONFIG_LEMOTE_YEELOONG2F) += yeeloong-2f/
arch/mips/loongson/common/cmdline.c +5 -0
@@ -21,6 +21,8 @@#include <linux/bootmem.h> #include <asm/bootinfo.h> +#include <loongson.h> +#include <cmdline.h> unsigned long bus_clock, cpu_clock_freq;unsigned long memsize, highmemsize;
@@ -55,6 +57,9 @@ void __init prom_init_cmdline(void)strcat (arcs_cmdline," " ); } +/* machine specific prom_init_cmdline */ +mach_prom_init_cmdline (); +/* handle console, root, busclock, cpuclock, memsize, highmemsize arguments */
arch/mips/loongson/yeeloong-2f/Makefile new file +5 -0
@@ -0,0 +1,5 @@ +# +# Makefile for fuloong-2f +# + +obj-y += init.o irq.o reset.o
arch/mips/loongson/yeeloong-2f/init.c new file +71 -0
71 lines not on this page · raw message
arch/mips/loongson/yeeloong-2f/irq.c new file +53 -0
53 lines not on this page · raw message
arch/mips/loongson/yeeloong-2f/reset.c new file +40 -0
@@ -0,0 +1,40 @@ +/* Board-specific reboot/shutdown routines +* Copyright (c) 2009 Philippe Vachon <[email protected]> +* +* Copyright (C) 2009 Lemote Inc. & Insititute of Computing Technology +* Author: Wu Zhangjin, [email protected] +* +* This program is free software; you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the +* Free Software Foundation; either version 2 of the License, or (at your +* option) any later version. +*/ + +#include <linux/types.h> + +#include <loongson.h> +#include <machine.h> + +void mach_prepare_reboot (void ) +{ +/* +* reset cpu to full speed, this is needed when enabling cpu frequency +* scalling +*/ +LOONGSON_CHIPCFG0 |=0x7 ; + +/* sending an reset signal to EC(embedded controller) */ +writeb (REG_RESET_HIGH , (u8 *) (mips_io_port_base +EC_IO_PORT_HIGH )); +writeb (REG_RESET_LOW , (u8 *) (mips_io_port_base +EC_IO_PORT_LOW )); +mmiowb (); +writeb (BIT_RESET_ON , (u8 *) (mips_io_port_base +EC_IO_PORT_DATA )); +mmiowb (); +} + +void mach_prepare_shutdown (void ) +{ +/* cpu-gpio0 output low */ +LOONGSON_GPIODATA &= ~0x00000001 ; +/* cpu-gpio0 as output */ +LOONGSON_GPIOIE &= ~0x00000001 ; +}
arch/mips/pci/Makefile +2 -1
@@ -27,7 +27,8 @@ obj-$(CONFIG_SOC_AU1500) += fixup-au1000.o ops-au1000.o obj-$(CONFIG_SOC_AU1550) += fixup-au1000.o ops-au1000.o obj-$(CONFIG_SOC_PNX8550) += fixup-pnx8550.o ops-pnx8550.o obj-$(CONFIG_LEMOTE_FULOONG2E) += fixup-fuloong2e.o ops-loongson2.o -obj-$(CONFIG_LEMOTE_FULOONG2F) += fixup-fuloong2f.o ops-loongson2.o +obj-$(CONFIG_LEMOTE_FULOONG2F) += fixup-lemote2f.o ops-loongson2.o +obj-$(CONFIG_LEMOTE_YEELOONG2F) += fixup-lemote2f.o ops-loongson2.o obj-$(CONFIG_MIPS_MALTA) += fixup-malta.o obj-$(CONFIG_PMC_MSP7120_GW) += fixup-pmcmsp.o ops-pmcmsp.o obj-$(CONFIG_PMC_MSP7120_EVAL) += fixup-pmcmsp.o ops-pmcmsp.o
arch/mips/pci/fixup-fuloong2f.c deleted +0 -171
171 lines not on this page · raw message
arch/mips/pci/fixup-lemote2f.c new file +171 -0
171 lines not on this page · raw message
Signature · 1 line
1.6.2.1
PATCH 16/27 Add Siliconmotion 712 framebuffer driver
In reply to [email protected]From: Wu Zhangjin <[email protected]>
yeeloong(2f) laptop has a SMI video card, need this driver.
this source code is originally from
http://dev.lemote.com/code/linux_loongson
tons of warnings have been fixed, the main warning is:
warning: left shift count >= width of type
have been fixed via the following modification:
drivers/video/smi/smtc2d.h:
#define _F_MASK(f) ((((1 << _F_SIZE(f)) - 1) << _F_START(f))
#define _F_MASK(f) (((1ULL << _F_SIZE(f)) - 1) << _F_START(f))besides, the coding style is changed to follow the kernel style, and two non-used header files are removed: sm501hw.h, sm7xxhw.h.
--- drivers/video/Kconfig | 23 + drivers/video/Makefile | 1 + drivers/video/smi/Makefile | 8 + drivers/video/smi/smtc2d.c | 979 +++++++++++++++++++++++++++++++++++++ drivers/video/smi/smtc2d.h | 530 ++++++++++++++++++++ drivers/video/smi/smtcfb.c | 1141 ++++++++++++++++++++++++++++++++++++++++++++ drivers/video/smi/smtcfb.h | 793 ++++++++++++++++++++++++++++++ 7 files changed, 3475 insertions(+), 0 deletions(-) create mode 100644 drivers/video/smi/Makefile create mode 100644 drivers/video/smi/smtc2d.c create mode 100644 drivers/video/smi/smtc2d.h create mode 100644 drivers/video/smi/smtcfb.c create mode 100644 drivers/video/smi/smtcfb.h
drivers/video/Kconfig +23 -0
@@ -1943,6 +1943,29 @@ config FB_S3C2410_DEBUG Turn on debugging messages. Note that you can set/unset at run time through sysfs +config FB_SILICONMOTION + bool "Silicon Motion Display Support" + depends on FB + help + Frame Buffer driver for the Silicon Motion serial graphic card. + +config FB_SM7XX + bool "Silicon Motion SM7XX Frame Buffer Support" + depends on FB_SILICONMOTION + depends on FB + select FB_CFB_FILLRECT + select FB_CFB_COPYAREA + select FB_CFB_IMAGEBLIT + help + Frame Buffer driver for the Silicon Motion SM7XX serial graphic card. + +config FB_SM7XX_ACCEL + bool "Siliconmotion Acceleration functions (EXPERIMENTAL)" + depends on FB_SM7XX && EXPERIMENTAL + help + This will compile the Trident frame buffer device with + acceleration functions. + config FB_SM501 tristate "Silicon Motion SM501 framebuffer support" depends on FB && MFD_SM501
drivers/video/Makefile +1 -0
@@ -71,6 +71,7 @@ obj-$(CONFIG_FB_P9100) += p9100.o sbuslib.o obj-$(CONFIG_FB_TCX) += tcx.o sbuslib.o obj-$(CONFIG_FB_LEO) += leo.o sbuslib.o obj-$(CONFIG_FB_SGIVW) += sgivwfb.o +obj-$(CONFIG_FB_SILICONMOTION) += smi/ obj-$(CONFIG_FB_ACORN) += acornfb.o obj-$(CONFIG_FB_ATARI) += atafb.o c2p_iplan2.o atafb_mfb.o \ atafb_iplan2p2.o atafb_iplan2p4.o atafb_iplan2p8.o
drivers/video/smi/Makefile new file +8 -0
@@ -0,0 +1,8 @@ +obj-y += smi.o + +smi-y := $(DRIVER_OBJS) + +smi-y += smtcfb.o + +EXTRA_CFLAGS += -Werror +
drivers/video/smi/smtc2d.c new file +979 -0
979 lines not on this page · raw message
drivers/video/smi/smtc2d.h new file +530 -0
530 lines not on this page · raw message
drivers/video/smi/smtcfb.c new file +1141 -0
1,141 lines not on this page · raw message
drivers/video/smi/smtcfb.h new file +793 -0
306 lines not on this page · raw message
The rest of this diff is not shown. View the raw message.
Signature · 1 line
1.6.2.1
Part of the diff is not shown here. View the raw message.
PATCH 17/27 define Loongson2F arch specific phys prot access
In reply to [email protected]From: Wu Zhangjin <[email protected]>
The main purpose is to uncache accelerate for video memory access
--- arch/mips/include/asm/pgtable.h | 13 ++++++++ arch/mips/loongson/Kconfig | 12 +++++++ arch/mips/loongson/common/mem.c | 63 +++++++++++++++++++++++++++++++++++++++ 3 files changed, 88 insertions(+), 0 deletions(-)
arch/mips/include/asm/pgtable.h +13 -0
@@ -370,6 +370,19 @@ static inline int io_remap_pfn_range(struct vm_area_struct *vma,#include <asm-generic/pgtable.h> /* +* uncache accelerate for video memory access +*/ +#ifdef CONFIG_LOONGSON2F +#define __HAVE_PHYS_MEM_ACCESS_PROT + +struct file ; +pgprot_t phys_mem_access_prot (struct file *file,unsigned long pfn, +unsigned long size,pgprot_t vma_prot); +int phys_mem_access_prot_allowed (struct file *file,unsigned long pfn, +unsigned long size,pgprot_t *vma_prot); +#endif + +/* * We provide our own get_unmapped area to cope with the virtual aliasing * constraints placed on us by the cache architecture. */
arch/mips/loongson/Kconfig +12 -0
@@ -114,3 +114,15 @@ config CS5536_UDC config SYS_HAS_MACH_PROM_INIT_CMDLINE bool + +config UCA_SIZE + hex "Uncache Accelerated Region size" + depends on CPU_LOONGSON2F + default 0x400000 if LEMOTE_YEELOONG2F + default 0x2000000 if LEMOTE_FULOONG2F + help + Uncached Acceleration(UCA) can greatly improve video performance. + Normally the Video memory can be accessed in Uncached Accelerated mode, + other peripheral spaces not. + + Specify a zeroed size to disable this feature.
arch/mips/loongson/common/mem.c +63 -0
66 lines not on this page · raw message
Signature · 1 line
1.6.2.1
PATCH 18/27 Loongson2 specific OProfile driver
In reply to [email protected]From: Wu Zhangjin <[email protected]>
this driver is used by the user-space tool:oprofile to profile linux kernel or applications via loongson2 performance counters. you can enable this driver via CONFIG_OPROFILE = y or m.
In loongson2, there are two performance counters, each one can count 16 events respectively. when anyone of the performance counter overflows, an interrupt will generate and goes to the interrupt line:MIPS_CPU_IRQ_BASE + 6, in fuloong2e, this interrupt line is exclusivly used by perf counter, but in fuloong2f & yeeloong2f, this interrupt line is shared by perf counter and the CPU internal north bridge(bonito64 compatiable).
NOTE: a patch should be sent to oprofile with the loongson-specific support. otherwise, the oprofile tool will not recognize this and complain about "cpu_type 'unset' is not valid". currently, the cpu_type is hard-coded in arch/mips/oprofile/op_model_loongson2.c as 'mips/loongson2'
--- arch/mips/include/asm/mach-loongson/loongson.h | 2 + arch/mips/include/asm/mach-loongson/machine.h | 1 - arch/mips/loongson/common/irq.c | 26 +++- arch/mips/loongson/fuloong-2e/irq.c | 2 + arch/mips/loongson/fuloong-2f/irq.c | 6 +- arch/mips/loongson/yeeloong-2f/irq.c | 6 +- arch/mips/oprofile/Makefile | 1 + arch/mips/oprofile/common.c | 5 + arch/mips/oprofile/op_model_loongson2.c | 186 ++++++++++++++++++++++++ 9 files changed, 227 insertions(+), 8 deletions(-) create mode 100644 arch/mips/oprofile/op_model_loongson2.c
arch/mips/include/asm/mach-loongson/loongson.h +2 -0
@@ -45,7 +45,9 @@ extern void mach_prepare_shutdown(void);#define LOONGSON_REG (x) \ (*(u32 *)((char *)CKSEG1ADDR(LOONGSON_REG_BASE) + (x))) +#define LOONGSON_IRQ_BASE 32 +#define LOONGSON_PERFCNT_IRQ (MIPS_CPU_IRQ_BASE + 6)/* cpu perf counter */ #define LOONGSON_FLASH_BASE 0x1c000000#define LOONGSON_FLASH_SIZE 0x02000000/* 32M */
arch/mips/include/asm/mach-loongson/machine.h +0 -1
@@ -63,7 +63,6 @@#if defined(CONFIG_LEMOTE_FULOONG2F ) || defined(CONFIG_LEMOTE_YEELOONG2F )#define LOONGSON_TIMER_IRQ (MIPS_CPU_IRQ_BASE + 7)/* cpu timer */ -#define LOONGSON_PERFCNT_IRQ (MIPS_CPU_IRQ_BASE + 6)/* cpu perf counter */ #define LOONGSON_NORTH_BRIDGE_IRQ (MIPS_CPU_IRQ_BASE + 6)/* bonito */ #define LOONGSON_UART_IRQ (MIPS_CPU_IRQ_BASE + 3)/* cpu serial port */ #define LOONGSON_SOUTH_BRIDGE_IRQ (MIPS_CPU_IRQ_BASE + 2)/* i8259 */
arch/mips/loongson/common/irq.c +25 -1
@@ -71,6 +71,30 @@ static struct irqaction cascade_irqaction = { .name = "cascade", }; +/* +* fuloong2f and yeeloong2f share the cpu perf counter interrupt and the north +* bridge interrupt in IP6, so, the ip6_irqaction should be sharable. +* otherwise, we will can not request the perf counter irq(setup the perf +* counter irq handler) in op_model_loongson2.c. +*/ + +#if defined(CONFIG_OPROFILE ) && \ + defined(CONFIG_LEMOTE_FULOONG2F ) || defined(CONFIG_LEMOTE_YEELOONG2F ) +irqreturn_t ip6_action (int cpl,void *dev_id) +{ +return IRQ_HANDLED ; +} + +static struct irqaction ip6_irqaction = { + .handler = ip6_action, + .mask =CPU_MASK_NONE , + .name ="cascade" , + .flags =IRQF_SHARED , +}; +#else +#define ip6_irqaction cascade_irqaction +#endif +void __init arch_init_irq (void ) {/*
@@ -104,7 +128,7 @@ void __init arch_init_irq(void)bonito_irq_init ();/* setup north bridge irq (bonito) */ -setup_irq (LOONGSON_NORTH_BRIDGE_IRQ , &cascade_irqaction); +setup_irq (LOONGSON_NORTH_BRIDGE_IRQ , &ip6_irqaction);/* setup source bridge irq (i8259) */ setup_irq (LOONGSON_SOUTH_BRIDGE_IRQ , &cascade_irqaction); }
arch/mips/loongson/fuloong-2e/irq.c +2 -0
@@ -40,6 +40,8 @@ inline void mach_irq_dispatch(unsigned int pending) {if (pending &CAUSEF_IP7 )do_IRQ (LOONGSON_TIMER_IRQ ); +else if (pending &CAUSEF_IP6 )/* perf counter loverflow */ +do_IRQ (LOONGSON_PERFCNT_IRQ );else if (pending &CAUSEF_IP5 )i8259_irqdispatch ();else if (pending &CAUSEF_IP2 )
arch/mips/loongson/fuloong-2f/irq.c +3 -3
@@ -34,9 +34,9 @@ inline void mach_irq_dispatch(unsigned int pending) {if (pending &CAUSEF_IP7 )do_IRQ (LOONGSON_TIMER_IRQ ); -else if (pending &CAUSEF_IP6 ) {/* North Bridge, Perf counter */ -do_IRQ (LOONGSON_PERFCNT_IRQ ); -bonito_irqdispatch (); +else if (pending &CAUSEF_IP6 ) { +do_IRQ (LOONGSON_PERFCNT_IRQ );/* Perf counter overflow */ +bonito_irqdispatch ();/* North Bridge */ }else if (pending &CAUSEF_IP3 )/* CPU UART */ do_IRQ (LOONGSON_UART_IRQ );else if (pending &CAUSEF_IP2 )/* South Bridge */
arch/mips/loongson/yeeloong-2f/irq.c +3 -3
@@ -34,9 +34,9 @@ inline void mach_irq_dispatch(unsigned int pending) {if (pending &CAUSEF_IP7 )do_IRQ (LOONGSON_TIMER_IRQ ); -else if (pending &CAUSEF_IP6 ) {/* North Bridge, Perf counter */ -do_IRQ (LOONGSON_PERFCNT_IRQ ); -bonito_irqdispatch (); +else if (pending &CAUSEF_IP6 ) { +do_IRQ (LOONGSON_PERFCNT_IRQ );/* Perf counter overflow */ +bonito_irqdispatch ();/* North Bridge */ }else if (pending &CAUSEF_IP3 )/* CPU UART */ do_IRQ (LOONGSON_UART_IRQ );else if (pending &CAUSEF_IP2 )/* South Bridge */
arch/mips/oprofile/Makefile +1 -0
@@ -15,3 +15,4 @@ oprofile-$(CONFIG_CPU_MIPS64) += op_model_mipsxx.o oprofile-$(CONFIG_CPU_R10000) += op_model_mipsxx.o oprofile-$(CONFIG_CPU_SB1) += op_model_mipsxx.o oprofile-$(CONFIG_CPU_RM9000) += op_model_rm9000.o +oprofile-$(CONFIG_CPU_LOONGSON2) += op_model_loongson2.o
arch/mips/oprofile/common.c +5 -0
@@ -16,6 +16,7 @@ extern struct op_mips_model op_model_mipsxx_ops __attribute__((weak)); extern struct op_mips_model op_model_rm9000_ops __attribute__((weak)); +extern struct op_mips_model op_model_loongson2_ops __attribute__((weak));static struct op_mips_model *model;
@@ -93,6 +94,10 @@ int __init oprofile_arch_init(struct oprofile_operations *ops)case CPU_RM9000 : lmodel = &op_model_rm9000_ops;break ; + +case CPU_LOONGSON2 : + lmodel = &op_model_loongson2_ops; +break ; };if (!lmodel)
arch/mips/oprofile/op_model_loongson2.c new file +186 -0
186 lines not on this page · raw message
Signature · 1 line
1.6.2.1
PATCH 19/27 flush posted write to irq
In reply to [email protected]From: Wu Zhangjin <[email protected]>
read back to flush the posted write, otherwise, there will be many spurious irqs.
the previous talk: http://www.spinics.net/lists/mips/msg33749.html
--- arch/mips/kernel/i8259.c | 2 ++ arch/mips/loongson/common/bonito-irq.c | 4 ++++ 2 files changed, 6 insertions(+), 0 deletions(-)
arch/mips/kernel/i8259.c +2 -0
@@ -177,10 +177,12 @@ handle_real_irq:outb (cached_slave_mask,PIC_SLAVE_IMR );outb (0x60 +(irq&7 ),PIC_SLAVE_CMD );/* 'Specific EOI' to slave */ outb (0x60 +PIC_CASCADE_IR ,PIC_MASTER_CMD );/* 'Specific EOI' to master-IRQ2 */ +inb (PIC_MASTER_CMD );/* flush posted write */ }else {inb (PIC_MASTER_IMR );/* DUMMY - (do we need this?) */ outb (cached_master_mask,PIC_MASTER_IMR );outb (0x60 +irq,PIC_MASTER_CMD );/* 'Specific EOI to master */ +inb (PIC_MASTER_CMD );/* flush posted write */ }smtc_im_ack_irq (irq);spin_unlock_irqrestore (&i8259A_lock, flags);
arch/mips/loongson/common/bonito-irq.c +4 -0
@@ -36,12 +36,16 @@static inline void bonito_irq_enable (unsigned int irq) {LOONGSON_INTENSET = (1 << (irq -LOONGSON_IRQ_BASE )); +/* flush posted write */ + (void )LOONGSON_INTENSET ;mmiowb (); }static inline void bonito_irq_disable (unsigned int irq) {LOONGSON_INTENCLR = (1 << (irq -LOONGSON_IRQ_BASE )); +/* flush posted write */ + (void )LOONGSON_INTENCLR ;mmiowb (); }
Signature · 1 line
1.6.2.1
PATCH 20/27 CS5536 MFGPT as system clock source support
In reply to [email protected]From: Wu Zhangjin <[email protected]>
The cpu count timer should not be used if oprofile and cpufreq are enabled. Instead, the CS5536's mfgpt is a proper timer alternative.
--- .../asm/mach-loongson/cs5536/cs5536_mfgpt.h | 26 ++ arch/mips/loongson/Kconfig | 15 +- arch/mips/loongson/common/cs5536/Makefile | 5 + arch/mips/loongson/common/cs5536/cs5536_mfgpt.c | 258 ++++++++++++++++++++ arch/mips/loongson/common/time.c | 7 + 5 files changed, 307 insertions(+), 4 deletions(-) create mode 100644 arch/mips/include/asm/mach-loongson/cs5536/cs5536_mfgpt.h create mode 100644 arch/mips/loongson/common/cs5536/cs5536_mfgpt.c
arch/mips/include/asm/mach-loongson/cs5536/cs5536_mfgpt.h new file +26 -0
@@ -0,0 +1,26 @@ +/* +* cs5536 mfgpt header file +*/ + +#ifndef _CS5536_MFGPT_H +#define _CS5536_MFGPT_H + +#include <cs5536/cs5536.h> + +extern void setup_mfgpt_timer (void ); + +#if 1 +#define MFGPT_TICK_RATE 14318000 +#else +#define MFGPT_TICK_RATE (14318180 / 8) +#endif +#define COMPARE ((MFGPT_TICK_RATE + HZ/2) / HZ) + +#define CS5536_MFGPT_INTR 5 + +#define MFGPT_BASE mfgpt_base +#define MFGPT0_CMP2 (MFGPT_BASE + 2) +#define MFGPT0_CNT (MFGPT_BASE + 4) +#define MFGPT0_SETUP (MFGPT_BASE + 6) + +#endif /*!_CS5536_MFGPT_H */
arch/mips/loongson/Kconfig +11 -4
@@ -32,8 +32,8 @@ config LEMOTE_FULOONG2E config LEMOTE_FULOONG2F bool "Lemote Fuloong(2f) mini-PC" select ARCH_SPARSEMEM_ENABLE - select CEVT_R4K - select CSRC_R4K + select CEVT_R4K if !CS5536_MFGPT + select CSRC_R4K if !CS5536_MFGPT select SYS_HAS_CPU_LOONGSON2F select DMA_NONCOHERENT select BOOT_ELF32
@@ -62,8 +62,8 @@ config LEMOTE_FULOONG2F config LEMOTE_YEELOONG2F bool "Lemote Yeeloong(2f) mini Notebook" select ARCH_SPARSEMEM_ENABLE - select CEVT_R4K - select CSRC_R4K + select CEVT_R4K if !CS5536_MFGPT + select CSRC_R4K if !CS5536_MFGPT select SYS_HAS_CPU_LOONGSON2F select DMA_NONCOHERENT select BOOT_ELF32
@@ -115,6 +115,13 @@ config CS5536_UDC config SYS_HAS_MACH_PROM_INIT_CMDLINE bool +config CS5536_MFGPT + bool "Using cs5536's MFGPT as system clock" + depends on CS5536 + help + This is needed if cpufreq and oprofile is enabled in Loongson2(F) + machines + config UCA_SIZE hex "Uncache Accelerated Region size" depends on CPU_LOONGSON2F
arch/mips/loongson/common/cs5536/Makefile +5 -0
@@ -17,4 +17,9 @@ obj-$(CONFIG_CS5536_NOR_FLASH) += cs5536_flash.o obj-$(CONFIG_CS5536_OTG) += cs5536_otg.o obj-$(CONFIG_CS5536_UDC) += cs5536_udc.o +# +# Enable cs5536 mfgpt Timer +# +obj-$(CONFIG_CS5536_MFGPT) += cs5536_mfgpt.o + EXTRA_CFLAGS += -Werror
arch/mips/loongson/common/cs5536/cs5536_mfgpt.c new file +258 -0
258 lines not on this page · raw message
arch/mips/loongson/common/time.c +7 -0
@@ -14,6 +14,9 @@#include <asm/time.h> #include <loongson.h> +#ifdef CONFIG_CS5536_MFGPT +#include <cs5536/cs5536_mfgpt.h> +#endif unsigned long read_persistent_clock (void ) {
@@ -24,4 +27,8 @@ void __init plat_time_init(void) {/* setup mips r4k timer */ mips_hpt_frequency = cpu_clock_freq /2 ; + +#ifdef CONFIG_CS5536_MFGPT +setup_mfgpt_timer (); +#endif }
Signature · 1 line
1.6.2.1
PATCH 21/27 Loongson2F cpufreq support
In reply to [email protected]From: Wu Zhangjin <[email protected]>
Loongson2F add a new capability to dynamic scaling cpu frequency. However the cpu count timer depends on cpu frequency. So an alternative clock must be used if this driver is enabled. Besides, the CPU enter wait state when the frequency is setting zero. All these features help power save.
In fuloong(2f) and yeeloong(2f), if you want to use this feature, you should enable the cs5536 mfgpt timer.
--- arch/mips/Kconfig | 17 ++ arch/mips/include/asm/clock.h | 64 +++++++ arch/mips/include/asm/mach-loongson/loongson.h | 7 + arch/mips/kernel/Makefile | 1 + arch/mips/kernel/loongson2f_freq.c | 223 ++++++++++++++++++++++++ arch/mips/loongson/common/Makefile | 6 + arch/mips/loongson/common/clock.c | 166 ++++++++++++++++++ 7 files changed, 484 insertions(+), 0 deletions(-) create mode 100644 arch/mips/include/asm/clock.h create mode 100644 arch/mips/kernel/loongson2f_freq.c create mode 100644 arch/mips/loongson/common/clock.c
arch/mips/Kconfig +17 -0
@@ -2138,6 +2138,23 @@ source "kernel/power/Kconfig" endmenu +menu "CPU Frequency scaling" + +source "drivers/cpufreq/Kconfig" + +config LOONGSON2F_CPU_FREQ + bool "Loongson-2F CPU Frequency driver" + depends on CPU_LOONGSON2F && CPU_FREQ && CS5536_MFGPT + select CPU_FREQ_TABLE + help + This adds the cpufreq driver for Loongson-2F. + + For details, take a look at <file:Documentation/cpu-freq>. + + If unsure, say N. + +endmenu + source "net/Kconfig" source "drivers/Kconfig"
arch/mips/include/asm/clock.h new file +64 -0
64 lines not on this page · raw message
arch/mips/include/asm/mach-loongson/loongson.h +7 -0
@@ -43,6 +43,13 @@ extern inline void mach_irq_dispatch(unsigned int pending);extern void mach_prepare_reboot (void );extern void mach_prepare_shutdown (void ); +/* loongson-specific cpu frequency relative stuff */ +#ifdef CONFIG_LOONGSON2F_CPU_FREQ +#include <linux/cpufreq.h> +extern void loongson2f_cpu_wait (void ); +extern struct cpufreq_frequency_table loongson2f_clockmod_table[]; +#endif +#define LOONGSON_REG (x) \ (*(u32 *)((char *)CKSEG1ADDR(LOONGSON_REG_BASE) + (x)))
arch/mips/kernel/Makefile +1 -0
@@ -73,6 +73,7 @@ obj-$(CONFIG_64BIT) += scall64-64.o obj-$(CONFIG_MIPS32_COMPAT) += linux32.o ptrace32.o signal32.o obj-$(CONFIG_MIPS32_N32) += binfmt_elfn32.o scall64-n32.o signal_n32.o obj-$(CONFIG_MIPS32_O32) += binfmt_elfo32.o scall64-o32.o +obj-$(CONFIG_LOONGSON2F_CPU_FREQ) += loongson2f_freq.o obj-$(CONFIG_KGDB) += kgdb.o obj-$(CONFIG_PROC_FS) += proc.o
arch/mips/kernel/loongson2f_freq.c new file +223 -0
223 lines not on this page · raw message
arch/mips/loongson/common/Makefile +6 -0
@@ -24,6 +24,12 @@ obj-$(CONFIG_RTC_DRV_CMOS) += rtc.o obj-$(CONFIG_CS5536) += cs5536/ # +# Enable fuloong(2f) and yeeloong(2f) cpu frequency scaling support +# This is based on CS5536 mfgpt timer +# +obj-$(CONFIG_LOONGSON2F_CPU_FREQ) += clock.o + +# # Enable serial port # obj-$(CONFIG_SERIAL_8250) += serial.o
arch/mips/loongson/common/clock.c new file +166 -0
166 lines not on this page · raw message
Signature · 1 line
1.6.2.1
PATCH 22/27 Hibernation Support in mips system
In reply to [email protected]From: Wu Zhangjin <[email protected]>
This is directly pulled from the to-mips branch of
http://dev.lemote.com/code/linux_loongson, only a few coding style tuning under the support of script/checkpatch.pl
--- arch/mips/Kconfig | 3 + arch/mips/Makefile | 3 + arch/mips/include/asm/suspend.h | 2 + arch/mips/kernel/asm-offsets.c | 13 ++++++ arch/mips/power/Makefile | 1 + arch/mips/power/cpu.c | 51 +++++++++++++++++++++++++ arch/mips/power/hibernate.S | 78 +++++++++++++++++++++++++++++++++++++++ include/linux/suspend.h | 3 +- 8 files changed, 153 insertions(+), 1 deletions(-) create mode 100644 arch/mips/power/Makefile create mode 100644 arch/mips/power/cpu.c create mode 100644 arch/mips/power/hibernate.S
arch/mips/Kconfig +3 -0
@@ -2130,6 +2130,9 @@ endmenu menu "Power management options" +config ARCH_HIBERNATION_POSSIBLE + def_bool y + config ARCH_SUSPEND_POSSIBLE def_bool y depends on !SMP
arch/mips/Makefile +3 -0
@@ -677,6 +677,9 @@ core-y += arch/mips/kernel/ arch/mips/mm/ arch/mips/math-emu/ drivers-$(CONFIG_OPROFILE) += arch/mips/oprofile/ +# suspend and hibernation support +drivers-$(CONFIG_PM) += arch/mips/power/ + ifdef CONFIG_LASAT rom.bin rom.sw: vmlinux $(Q)$(MAKE) $(build)=arch/mips/lasat/image $@
arch/mips/include/asm/suspend.h +2 -0
@@ -3,4 +3,6 @@/* Somewhen... Maybe :-) */ +static inline int arch_prepare_suspend (void ) {return 0 ; } +#endif /* __ASM_SUSPEND_H */
arch/mips/kernel/asm-offsets.c +13 -0
@@ -14,6 +14,7 @@#include <linux/mm.h> #include <linux/interrupt.h> #include <linux/kbuild.h> +#include <linux/suspend.h> #include <asm/ptrace.h> #include <asm/processor.h>
@@ -326,3 +327,15 @@ void output_octeon_cop2_state_defines(void) BLANK(); }#endif + +#ifdef CONFIG_HIBERNATION +void output_pbe_defines (void ) +{ +COMMENT (" Linux struct pbe offsets. " ); +OFFSET (PBE_ADDRESS , pbe, address); +OFFSET (PBE_ORIG_ADDRESS , pbe, orig_address); +OFFSET (PBE_NEXT , pbe, next); +DEFINE (PBE_SIZE ,sizeof (struct pbe )); +BLANK (); +} +#endif
arch/mips/power/Makefile new file +1 -0
@@ -0,0 +1 @@ +obj-$(CONFIG_HIBERNATION) += cpu.o hibernate.o
arch/mips/power/cpu.c new file +51 -0
51 lines not on this page · raw message
arch/mips/power/hibernate.S new file +78 -0
78 lines not on this page · raw message
include/linux/suspend.h +2 -1
@@ -1,7 +1,8 @@#ifndef _LINUX_SUSPEND_H#define _LINUX_SUSPEND_H -#if defined(CONFIG_X86 ) || defined(CONFIG_FRV ) || defined(CONFIG_PPC32 ) || defined(CONFIG_PPC64 ) +#if defined(CONFIG_X86 ) || defined(CONFIG_FRV ) || defined(CONFIG_PPC32 ) || \ + defined(CONFIG_PPC64 ) || defined(CONFIG_MIPS )#include <asm/suspend.h> #endif #include <linux/swap.h>
Signature · 1 line
1.6.2.1
PATCH 23/27 Alsa memory maps fixup on mips systems
In reply to [email protected]From: Wu Zhangjin <[email protected]>
The user application mmap audio dma regions must be dma-coherent.
this is directly pulled from the to-mips branch of
http://dev.lemote.com/code/linux_loongson
--- sound/core/pcm_native.c | 9 +++++++++ sound/core/sgbuf.c | 9 +++++++++ sound/pci/Kconfig | 1 - 3 files changed, 18 insertions(+), 1 deletions(-)
sound/core/pcm_native.c +9 -0
@@ -3099,7 +3099,11 @@ static int snd_pcm_mmap_data_fault(struct vm_area_struct *area,return VM_FAULT_SIGBUS ; }else { vaddr = runtime->dma_area + offset; +#if defined(__mips__) && defined(CONFIG_DMA_NONCOHERENT ) + page =virt_to_page (CAC_ADDR (vaddr)); +#else page =virt_to_page (vaddr); +#endif }get_page (page); vmf->page = page;
@@ -3214,6 +3218,11 @@ static int snd_pcm_mmap(struct file *file, struct vm_area_struct *area)if (PCM_RUNTIME_CHECK (substream))return -ENXIO ; +#if defined(__mips__) && defined(CONFIG_DMA_NONCOHERENT ) +/* all mmap using uncached mode */ + area->vm_page_prot =pgprot_noncached (area->vm_page_prot); + area->vm_flags |= (VM_RESERVED |VM_IO ); +#endif offset = area->vm_pgoff <<PAGE_SHIFT ;switch (offset) {case SNDRV_PCM_MMAP_OFFSET_STATUS :
sound/core/sgbuf.c +9 -0
@@ -114,7 +114,11 @@ void *snd_malloc_sgbuf_pages(struct device *device,if (!i) table->addr |= chunk;/* mark head */ table++; +#if defined(__mips__) && defined(CONFIG_DMA_NONCOHERENT ) + *pgtable++ =virt_to_page (CAC_ADDR (tmpb.area)); +#else *pgtable++ =virt_to_page (tmpb.area); +#endif tmpb.area +=PAGE_SIZE ; tmpb.addr +=PAGE_SIZE ; }
@@ -125,7 +129,12 @@ void *snd_malloc_sgbuf_pages(struct device *device, } sgbuf->size = size; +#if defined(__mips__) && defined(CONFIG_DMA_NONCOHERENT ) + dmab->area =vmap (sgbuf->page_table, sgbuf->pages, \ +VM_MAP |VM_IO ,pgprot_noncached (PAGE_KERNEL )); +#else dmab->area =vmap (sgbuf->page_table, sgbuf->pages,VM_MAP ,PAGE_KERNEL ); +#endif if (! dmab->area) goto _failed;if (res_size)
sound/pci/Kconfig +0 -1
@@ -259,7 +259,6 @@ config SND_CS5530 config SND_CS5535AUDIO tristate "CS5535/CS5536 Audio" - depends on X86 && !X86_64 select SND_PCM select SND_AC97_CODEC help
Signature · 1 line
1.6.2.1
Re: [loongson-PATCH-v1 01/27] fix-warning: incompatible argument type of pci_fixup_irqs
In reply to [email protected]Quoted 16 lines · [email protected] wrote:
From: Wu Zhangjin <[email protected]>
arch/mips/pci/pci.c:160: warning: passing argument 2 of ‘pci_fixup_irqs’ from incompatible pointer type
include/linux/pci.h:void pci_fixup_irqs(u8 (*)(struct pci_dev *, u8 *), int (*)(struct pci_dev *, u8, u8));
arch/mips/pci/pci.c:160:pci_fixup_irqs(pci_common_swizzle, pcibios_map_irq);
arch/mips/include/asm/pci.h:
Quoted 7 lines
extern int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin);
arch/mips/pci/fixup-malta.cint
__initpcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)Signed-off-by Wu Zhangjin <[email protected]>
This is the correct fix, however there are now Cavium Octeon PCI drivers on Ralf's queue.
If you rebase against the queue (or even if you don't), you can add:
Quoted 353 lines
--- arch/mips/include/asm/pci.h | 2 +- arch/mips/pci/fixup-au1000.c | 2 +- arch/mips/pci/fixup-capcella.c | 2 +- arch/mips/pci/fixup-cobalt.c | 2 +- arch/mips/pci/fixup-emma2rh.c | 2 +- arch/mips/pci/fixup-excite.c | 2 +- arch/mips/pci/fixup-ip32.c | 2 +- arch/mips/pci/fixup-lm2e.c | 2 +- arch/mips/pci/fixup-malta.c | 2 +- arch/mips/pci/fixup-mpc30x.c | 2 +- arch/mips/pci/fixup-pmcmsp.c | 2 +- arch/mips/pci/fixup-pnx8550.c | 2 +- arch/mips/pci/fixup-rc32434.c | 2 +- arch/mips/pci/fixup-sni.c | 2 +- arch/mips/pci/fixup-tb0219.c | 2 +- arch/mips/pci/fixup-tb0226.c | 2 +- arch/mips/pci/fixup-tb0287.c | 2 +- arch/mips/pci/fixup-wrppmc.c | 2 +- arch/mips/pci/fixup-yosemite.c | 2 +- arch/mips/pci/pci-bcm1480.c | 2 +- arch/mips/pci/pci-bcm47xx.c | 2 +- arch/mips/pci/pci-ip27.c | 2 +- arch/mips/pci/pci-lasat.c | 2 +- arch/mips/pci/pci-sb1250.c | 2 +- arch/mips/txx9/generic/pci.c | 2 +- 25 files changed, 25 insertions(+), 25 deletions(-)arch/mips/include/asm/pci.h +1
-1@@ -56,7 +56,7 @@ extern void register_pci_controller(struct pci_controller *hose);/* * board supplied pci irq fixup routine */ -extern int pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin); +extern int pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin);/* Can be used to override the logic in pci_scan_bus for skipping arch/mips/pci/fixup-au1000.c +1
-1@@ -31,7 +31,7 @@extern char irq_tab_alchemy[][5 ]; -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return irq_tab_alchemy[slot][pin]; }arch/mips/pci/fixup-capcella.c +1
-1@@ -38,7 +38,7 @@ static char irq_tab_capcella[][5] __initdata = { [14] = { -1, INTA, INTB, INTC, INTD } }; -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return irq_tab_capcella[slot][pin]; }arch/mips/pci/fixup-cobalt.c +1
-1@@ -175,7 +175,7 @@ static char irq_tab_raq2[] __initdata = { [COBALT_PCICONF_ETH1] = ETH1_IRQ }; -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {if (cobalt_board_id <=COBALT_BRD_ID_QUBE1 )return irq_tab_qube1[slot];arch/mips/pci/fixup-emma2rh.c +1
-1@@ -88,7 +88,7 @@ static void __devinit emma2rh_pci_host_fixup(struct pci_dev *dev)DECLARE_PCI_FIXUP_HEADER (PCI_VENDOR_ID_NEC ,PCI_DEVICE_ID_NEC_EMMA2RH , emma2rh_pci_host_fixup); -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return irq_map[slot][pin]; }arch/mips/pci/fixup-excite.c +1
-1@@ -21,7 +21,7 @@#include <linux/pci.h> #include <excite.h> -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {if (pin ==0 )return -1 ;arch/mips/pci/fixup-ip32.c +1
-1@@ -39,7 +39,7 @@ static char irq_tab_mace[][5] __initdata = {* irqs. I suppose a device without a pin A will thank us for doing it * right if there exists such a broken piece of crap. */ -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return irq_tab_mace[slot][pin]; }arch/mips/pci/fixup-lm2e.c +1
-1@@ -36,7 +36,7 @@/* South bridge slot number is set by the pci probe process */ static u8 sb_slot =5 ; -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {int irq =0 ;arch/mips/pci/fixup-malta.c +1
-1@@ -36,7 +36,7 @@ static char irq_tab[][5] __initdata = { {0, PCID, PCIA, PCIB, PCIC } /* 21: PCI Slot 4 */ }; -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {int virq; virq = irq_tab[slot][pin];arch/mips/pci/fixup-mpc30x.c +1
-1@@ -34,7 +34,7 @@ static const int irq_tab_mpc30x[] __initdata = { [29] = MQ200_IRQ, }; -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {if (slot ==30 )return internal_func_irqs[PCI_FUNC (dev->devfn)];arch/mips/pci/fixup-pmcmsp.c +1
-1@@ -202,7 +202,7 @@ int pcibios_plat_dev_init(struct pci_dev *dev)* RETURNS: IRQ number * ****************************************************************************/ -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {#if !defined(CONFIG_PMC_MSP7120_GW ) && !defined(CONFIG_PMC_MSP7120_EVAL )printk (KERN_WARNING "PCI: unknown board, no PCI IRQs assigned.\n" );arch/mips/pci/fixup-pnx8550.c +1
-1@@ -45,7 +45,7 @@ void __init pcibios_fixup(void)/* nothing to do here */ } -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return pnx8550_irq_tab[slot][pin]; }arch/mips/pci/fixup-rc32434.c +1
-1@@ -37,7 +37,7 @@ static int __devinitdata irq_map[2][12] = { {0, 0, 1, 3, 0, 2, 1, 3, 0, 2, 1, 3} }; -int __devinit pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __devinit pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {int irq =0 ;arch/mips/pci/fixup-sni.c +1
-1@@ -130,7 +130,7 @@ static inline int is_rm300_revd(void)return (csmsr &0xa0 ) ==0x20 ; } -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {switch (sni_brd_type) {case SNI_BRD_PCI_TOWER_CPLUS :arch/mips/pci/fixup-tb0219.c +1
-1@@ -23,7 +23,7 @@#include <asm/vr41xx/tb0219.h> -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {int irq =-1 ;arch/mips/pci/fixup-tb0226.c +1
-1@@ -23,7 +23,7 @@#include <asm/vr41xx/giu.h> #include <asm/vr41xx/tb0226.h> -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {int irq =-1 ;arch/mips/pci/fixup-tb0287.c +1
-1@@ -22,7 +22,7 @@#include <asm/vr41xx/tb0287.h> -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {unsigned char bus;int irq =-1 ;arch/mips/pci/fixup-wrppmc.c +1
-1@@ -25,7 +25,7 @@ static char pci_irq_tab[PCI_SLOT_MAXNR][5] __initdata = { [6] = {0, WRPPMC_PCI_INTA_IRQ, 0, 0, 0}, }; -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return pci_irq_tab[slot][pin]; }arch/mips/pci/fixup-yosemite.c +1
-1@@ -26,7 +26,7 @@#include <linux/init.h> #include <linux/pci.h> -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {if (pin ==0 )return -1 ;arch/mips/pci/pci-bcm1480.c +1
-1@@ -74,7 +74,7 @@ static inline void WRITECFG32(u32 addr, u32 data) *(u32 *)(cfg_space + (addr & ~3 )) = data; } -int pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {if (pin ==0 )return -1 ;arch/mips/pci/pci-bcm47xx.c +1
-1@@ -26,7 +26,7 @@#include <linux/pci.h> #include <linux/ssb/ssb.h> -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return 0 ; }arch/mips/pci/pci-ip27.c +1
-1@@ -141,7 +141,7 @@ int __cpuinit bridge_probe(nasid_t nasid, int widget_id, int masterwid)* A given PCI device, in general, should be able to intr any of the cpus * on any one of the hubs connected to its xbow. */ -int __devinit pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __devinit pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return 0 ; }arch/mips/pci/pci-lasat.c +1
-1@@ -61,7 +61,7 @@ arch_initcall(lasat_pci_setup);#define LASAT_IRQ_PCIC (LASAT_IRQ_BASE + 7)#define LASAT_IRQ_PCID (LASAT_IRQ_BASE + 8) -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {switch (slot) {case 1 :arch/mips/pci/pci-sb1250.c +1
-1@@ -84,7 +84,7 @@ static inline void WRITECFG32(u32 addr, u32 data) *(u32 *) (cfg_space + (addr & ~3 )) = data; } -int pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return dev->irq; }arch/mips/txx9/generic/pci.c +1
-1@@ -382,7 +382,7 @@ int pcibios_plat_dev_init(struct pci_dev *dev)return 0 ; } -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return txx9_board_vec->pci_map_irq (dev, slot, pin); }
PATCH 24/27 fixup for FUJITSU disk
In reply to [email protected]From: Wu Zhangjin <[email protected]>
This is originally from the to-mips branch from
http://dev.lemote.com/code/linux_loongson
--- drivers/ide/amd74xx.c | 19 +++++++++++++++++++ 1 files changed, 19 insertions(+), 0 deletions(-)
drivers/ide/amd74xx.c +19 -0
@@ -23,6 +23,11 @@#define DRV_NAME "amd74xx" +static const char *am74xx_quirk_drives[] = { +"FUJITSU MHZ2160BH G2" , +NULL +}; +enum {AMD_IDE_CONFIG =0x41 ,AMD_CABLE_DETECT =0x42 ,
@@ -112,6 +117,19 @@ static void amd_set_pio_mode(ide_drive_t *drive, const u8 pio)amd_set_drive (drive,XFER_PIO_0 + pio); } +static void amd_quirkproc (ide_drive_t *drive) +{ +const char **list, *m = (char *)&drive->id[ATA_ID_PROD ]; + +for (list = am74xx_quirk_drives; *list !=NULL ; list++) +if (strstr (m, *list) !=NULL ) { + drive->quirk_list =2 ; +return ; + } + + drive->quirk_list =0 ; +} +static void amd7409_cable_detect (struct pci_dev *dev) {/* no host side cable detection */
@@ -194,6 +212,7 @@ static void __devinit init_hwif_amd74xx(ide_hwif_t *hwif)static const struct ide_port_ops amd_port_ops = { .set_pio_mode = amd_set_pio_mode, .set_dma_mode = amd_set_drive, + .quirkproc = amd_quirkproc, .cable_detect = amd_cable_detect, };
Signature · 1 line
1.6.2.1
PATCH 25/27 Flush RAS and BTB for CPU predictively execution
In reply to [email protected]From: Wu Zhangjin <[email protected]>
This is directly picked from the to-mips branch of
http://dev.lemote.com/code/linux_loongson
--- arch/mips/include/asm/stackframe.h | 14 ++++++++++++++ 1 files changed, 14 insertions(+), 0 deletions(-)
arch/mips/include/asm/stackframe.h +14 -0
@@ -117,6 +117,20 @@ .endm #else .macro get_saved_sp /* Uniprocessor variation */ +#ifdef CONFIG_CPU_LOONGSON2 + move k0, ra + jal 2008f + nop +2008 : jal 2008f + nop +2008 : jal 2008f + nop +2008 : jal 2008f + nop +2008 : move ra, k0 + li k0, 3 + mtc0 k0, $22 +#endif #if defined(CONFIG_32BIT) || defined(KBUILD_64BIT_SYM32) lui k1, %hi(kernelsp) #else
Signature · 1 line
1.6.2.1
PATCH 26/27 add default kernel config file for loongson-based machines
In reply to [email protected]From: Wu Zhangjin <[email protected]>
these default kernel config files are stored in arch/mips/configs
config file machine
fuloong2e_defconfig --> fuloong(2e)
fuloong2f_defconfig --> fuloong(2f)
yeeloong2f_defconfig --> yeeloong(2f)by default, RTC, Serial Port, STD, MFGPT Timer(only for -2f), cpufreq(2f) are compilied in.
--- arch/mips/configs/fulong_defconfig | 1912 ----------------------- arch/mips/configs/fuloong2e_defconfig | 1977 ++++++++++++++++++++++++ arch/mips/configs/fuloong2f_defconfig | 2630 +++++++++++++++++++++++++++++++ arch/mips/configs/yeeloong2f_defconfig | 2641 ++++++++++++++++++++++++++++++++ 4 files changed, 7248 insertions(+), 1912 deletions(-) delete mode 100644 arch/mips/configs/fulong_defconfig create mode 100644 arch/mips/configs/fuloong2e_defconfig create mode 100644 arch/mips/configs/fuloong2f_defconfig create mode 100644 arch/mips/configs/yeeloong2f_defconfig
arch/mips/configs/fulong_defconfig deleted +0 -1912
@@ -1,1912 +0,0 @@ -# -# Automatically generated make config: don't edit -# Linux kernel version: 2.6.28-rc6 -# Fri Nov 28 17:53:48 2008 -# -CONFIG_MIPS=y - -# -# Machine selection -# -# CONFIG_MACH_ALCHEMY is not set -# CONFIG_BASLER_EXCITE is not set -# CONFIG_BCM47XX is not set -# CONFIG_MIPS_COBALT is not set -# CONFIG_MACH_DECSTATION is not set -# CONFIG_MACH_JAZZ is not set -# CONFIG_LASAT is not set -CONFIG_LEMOTE_FULONG=y -# CONFIG_MIPS_MALTA is not set -# CONFIG_MIPS_SIM is not set -# CONFIG_MACH_EMMA is not set -# CONFIG_MACH_VR41XX is not set -# CONFIG_NXP_STB220 is not set -# CONFIG_NXP_STB225 is not set -# CONFIG_PNX8550_JBS is not set -# CONFIG_PNX8550_STB810 is not set -# CONFIG_PMC_MSP is not set -# CONFIG_PMC_YOSEMITE is not set -# CONFIG_SGI_IP22 is not set -# CONFIG_SGI_IP27 is not set -# CONFIG_SGI_IP28 is not set -# CONFIG_SGI_IP32 is not set -# CONFIG_SIBYTE_CRHINE is not set -# CONFIG_SIBYTE_CARMEL is not set -# CONFIG_SIBYTE_CRHONE is not set -# CONFIG_SIBYTE_RHONE is not set -# CONFIG_SIBYTE_SWARM is not set -# CONFIG_SIBYTE_LITTLESUR is not set -# CONFIG_SIBYTE_SENTOSA is not set -# CONFIG_SIBYTE_BIGSUR is not set -# CONFIG_SNI_RM is not set -# CONFIG_MACH_TX39XX is not set -# CONFIG_MACH_TX49XX is not set -# CONFIG_MIKROTIK_RB532 is not set -# CONFIG_WR_PPMC is not set -CONFIG_RWSEM_GENERIC_SPINLOCK=y -# CONFIG_ARCH_HAS_ILOG2_U32 is not set -# CONFIG_ARCH_HAS_ILOG2_U64 is not set -CONFIG_ARCH_SUPPORTS_OPROFILE=y -CONFIG_GENERIC_FIND_NEXT_BIT=y -CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y -CONFIG_GENERIC_CLOCKEVENTS=y -CONFIG_GENERIC_TIME=y -CONFIG_GENERIC_CMOS_UPDATE=y -CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y -CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y -CONFIG_CEVT_R4K=y -CONFIG_CSRC_R4K=y -CONFIG_DMA_NONCOHERENT=y -CONFIG_DMA_NEED_PCI_MAP_STATE=y -CONFIG_EARLY_PRINTK=y -CONFIG_SYS_HAS_EARLY_PRINTK=y -# CONFIG_HOTPLUG_CPU is not set -CONFIG_I8259=y -# CONFIG_NO_IOPORT is not set -CONFIG_GENERIC_ISA_DMA=y -CONFIG_GENERIC_ISA_DMA_SUPPORT_BROKEN=y -# CONFIG_CPU_BIG_ENDIAN is not set -CONFIG_CPU_LITTLE_ENDIAN=y -CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y -CONFIG_IRQ_CPU=y -CONFIG_BOOT_ELF32=y -CONFIG_MIPS_L1_CACHE_SHIFT=5 -CONFIG_HAVE_STD_PC_SERIAL_PORT=y - -# -# CPU selection -# -CONFIG_CPU_LOONGSON2=y -# CONFIG_CPU_MIPS32_R1 is not set -# CONFIG_CPU_MIPS32_R2 is not set -# CONFIG_CPU_MIPS64_R1 is not set -# CONFIG_CPU_MIPS64_R2 is not set -# CONFIG_CPU_R3000 is not set -# CONFIG_CPU_TX39XX is not set -# CONFIG_CPU_VR41XX is not set -# CONFIG_CPU_R4300 is not set -# CONFIG_CPU_R4X00 is not set -# CONFIG_CPU_TX49XX is not set -# CONFIG_CPU_R5000 is not set -# CONFIG_CPU_R5432 is not set -# CONFIG_CPU_R5500 is not set -# CONFIG_CPU_R6000 is not set -# CONFIG_CPU_NEVADA is not set -# CONFIG_CPU_R8000 is not set -# CONFIG_CPU_R10000 is not set -# CONFIG_CPU_RM7000 is not set -# CONFIG_CPU_RM9000 is not set -# CONFIG_CPU_SB1 is not set -CONFIG_SYS_HAS_CPU_LOONGSON2=y -CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y -CONFIG_SYS_SUPPORTS_64BIT_KERNEL=y -CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y -CONFIG_CPU_SUPPORTS_64BIT_KERNEL=y - -# -# Kernel type -# -# CONFIG_32BIT is not set -CONFIG_64BIT=y -# CONFIG_PAGE_SIZE_4KB is not set -# CONFIG_PAGE_SIZE_8KB is not set -CONFIG_PAGE_SIZE_16KB=y -# CONFIG_PAGE_SIZE_64KB is not set -CONFIG_BOARD_SCACHE=y -CONFIG_MIPS_MT_DISABLED=y -# CONFIG_MIPS_MT_SMP is not set -# CONFIG_MIPS_MT_SMTC is not set -CONFIG_CPU_HAS_WB=y -CONFIG_CPU_HAS_SYNC=y -CONFIG_GENERIC_HARDIRQS=y -CONFIG_GENERIC_IRQ_PROBE=y -CONFIG_CPU_SUPPORTS_HIGHMEM=y -CONFIG_SYS_SUPPORTS_HIGHMEM=y -CONFIG_ARCH_FLATMEM_ENABLE=y -CONFIG_ARCH_POPULATES_NODE_MAP=y -CONFIG_ARCH_SPARSEMEM_ENABLE=y -CONFIG_SELECT_MEMORY_MODEL=y -CONFIG_FLATMEM_MANUAL=y -# CONFIG_DISCONTIGMEM_MANUAL is not set -# CONFIG_SPARSEMEM_MANUAL is not set -CONFIG_FLATMEM=y -CONFIG_FLAT_NODE_MEM_MAP=y -CONFIG_SPARSEMEM_STATIC=y -CONFIG_PAGEFLAGS_EXTENDED=y -CONFIG_SPLIT_PTLOCK_CPUS=4 -CONFIG_RESOURCES_64BIT=y -CONFIG_PHYS_ADDR_T_64BIT=y -CONFIG_ZONE_DMA_FLAG=0 -CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y -CONFIG_TICK_ONESHOT=y -CONFIG_NO_HZ=y -CONFIG_HIGH_RES_TIMERS=y -CONFIG_GENERIC_CLOCKEVENTS_BUILD=y -# CONFIG_HZ_48 is not set -# CONFIG_HZ_100 is not set -# CONFIG_HZ_128 is not set -CONFIG_HZ_250=y -# CONFIG_HZ_256 is not set -# CONFIG_HZ_1000 is not set -# CONFIG_HZ_1024 is not set -CONFIG_SYS_SUPPORTS_ARBIT_HZ=y -CONFIG_HZ=250 -# CONFIG_PREEMPT_NONE is not set -CONFIG_PREEMPT_VOLUNTARY=y -# CONFIG_PREEMPT is not set -# CONFIG_KEXEC is not set -CONFIG_SECCOMP=y -CONFIG_LOCKDEP_SUPPORT=y -CONFIG_STACKTRACE_SUPPORT=y -CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" - -# -# General setup -# -CONFIG_EXPERIMENTAL=y -CONFIG_BROKEN_ON_SMP=y -CONFIG_INIT_ENV_ARG_LIMIT=32 -CONFIG_LOCALVERSION="lm32" -# CONFIG_LOCALVERSION_AUTO is not set -CONFIG_SWAP=y -CONFIG_SYSVIPC=y -CONFIG_SYSVIPC_SYSCTL=y -CONFIG_POSIX_MQUEUE=y -CONFIG_BSD_PROCESS_ACCT=y -# CONFIG_BSD_PROCESS_ACCT_V3 is not set -# CONFIG_TASKSTATS is not set -# CONFIG_AUDIT is not set -CONFIG_IKCONFIG=y -CONFIG_IKCONFIG_PROC=y -CONFIG_LOG_BUF_SHIFT=14 -# CONFIG_CGROUPS is not set -# CONFIG_GROUP_SCHED is not set -CONFIG_SYSFS_DEPRECATED=y -CONFIG_SYSFS_DEPRECATED_V2=y -# CONFIG_RELAY is not set -CONFIG_NAMESPACES=y -# CONFIG_UTS_NS is not set -# CONFIG_IPC_NS is not set -CONFIG_USER_NS=y -CONFIG_PID_NS=y -# CONFIG_BLK_DEV_INITRD is not set -# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set -CONFIG_SYSCTL=y -CONFIG_EMBEDDED=y -CONFIG_SYSCTL_SYSCALL=y -CONFIG_KALLSYMS=y -# CONFIG_KALLSYMS_EXTRA_PASS is not set -CONFIG_HOTPLUG=y -CONFIG_PRINTK=y -CONFIG_BUG=y -CONFIG_ELF_CORE=y -# CONFIG_PCSPKR_PLATFORM is not set -# CONFIG_COMPAT_BRK is not set -CONFIG_BASE_FULL=y -CONFIG_FUTEX=y -CONFIG_ANON_INODES=y -CONFIG_EPOLL=y -CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y -CONFIG_EVENTFD=y -CONFIG_SHMEM=y -CONFIG_AIO=y -CONFIG_VM_EVENT_COUNTERS=y -CONFIG_PCI_QUIRKS=y -CONFIG_SLAB=y -# CONFIG_SLUB is not set -# CONFIG_SLOB is not set -CONFIG_PROFILING=y -# CONFIG_MARKERS is not set -CONFIG_OPROFILE=m -CONFIG_HAVE_OPROFILE=y -# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set -CONFIG_SLABINFO=y -CONFIG_RT_MUTEXES=y -# CONFIG_TINY_SHMEM is not set -CONFIG_BASE_SMALL=0 -CONFIG_MODULES=y -# CONFIG_MODULE_FORCE_LOAD is not set -CONFIG_MODULE_UNLOAD=y -CONFIG_MODULE_FORCE_UNLOAD=y -# CONFIG_MODVERSIONS is not set -# CONFIG_MODULE_SRCVERSION_ALL is not set -CONFIG_KMOD=y -CONFIG_BLOCK=y -# CONFIG_BLK_DEV_IO_TRACE is not set -CONFIG_BLK_DEV_BSG=y -# CONFIG_BLK_DEV_INTEGRITY is not set -CONFIG_BLOCK_COMPAT=y - -# -# IO Schedulers -# -CONFIG_IOSCHED_NOOP=y -CONFIG_IOSCHED_AS=y -CONFIG_IOSCHED_DEADLINE=y -CONFIG_IOSCHED_CFQ=y -# CONFIG_DEFAULT_AS is not set -# CONFIG_DEFAULT_DEADLINE is not set -CONFIG_DEFAULT_CFQ=y -# CONFIG_DEFAULT_NOOP is not set -CONFIG_DEFAULT_IOSCHED="cfq" -CONFIG_CLASSIC_RCU=y -CONFIG_FREEZER=y - -# -# Bus options (PCI, PCMCIA, EISA, ISA, TC) -# -CONFIG_HW_HAS_PCI=y -CONFIG_PCI=y -CONFIG_PCI_DOMAINS=y -# CONFIG_ARCH_SUPPORTS_MSI is not set -CONFIG_PCI_LEGACY=y -CONFIG_ISA=y -CONFIG_MMU=y -# CONFIG_PCCARD is not set -# CONFIG_HOTPLUG_PCI is not set - -# -# Executable file formats -# -CONFIG_BINFMT_ELF=y -# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set -# CONFIG_HAVE_AOUT is not set -CONFIG_BINFMT_MISC=y -CONFIG_MIPS32_COMPAT=y -CONFIG_COMPAT=y -CONFIG_SYSVIPC_COMPAT=y -CONFIG_MIPS32_O32=y -CONFIG_MIPS32_N32=y -CONFIG_BINFMT_ELF32=y - -# -# Power management options -# -CONFIG_ARCH_SUSPEND_POSSIBLE=y -CONFIG_PM=y -# CONFIG_PM_DEBUG is not set -CONFIG_PM_SLEEP=y -CONFIG_SUSPEND=y -CONFIG_SUSPEND_FREEZER=y -CONFIG_NET=y - -# -# Networking options -# -CONFIG_PACKET=y -CONFIG_PACKET_MMAP=y -CONFIG_UNIX=y -CONFIG_XFRM=y -# CONFIG_XFRM_USER is not set -# CONFIG_XFRM_SUB_POLICY is not set -# CONFIG_XFRM_MIGRATE is not set -# CONFIG_XFRM_STATISTICS is not set -# CONFIG_NET_KEY is not set -CONFIG_INET=y -CONFIG_IP_MULTICAST=y -# CONFIG_IP_ADVANCED_ROUTER is not set -CONFIG_IP_FIB_HASH=y -CONFIG_IP_PNP=y -# CONFIG_IP_PNP_DHCP is not set -CONFIG_IP_PNP_BOOTP=y -# CONFIG_IP_PNP_RARP is not set -CONFIG_NET_IPIP=m -CONFIG_NET_IPGRE=m -CONFIG_NET_IPGRE_BROADCAST=y -# CONFIG_IP_MROUTE is not set -# CONFIG_ARPD is not set -# CONFIG_SYN_COOKIES is not set -# CONFIG_INET_AH is not set -# CONFIG_INET_ESP is not set -# CONFIG_INET_IPCOMP is not set -# CONFIG_INET_XFRM_TUNNEL is not set -CONFIG_INET_TUNNEL=m -# CONFIG_INET_XFRM_MODE_TRANSPORT is not set -# CONFIG_INET_XFRM_MODE_TUNNEL is not set -CONFIG_INET_XFRM_MODE_BEET=y -# CONFIG_INET_LRO is not set -# CONFIG_INET_DIAG is not set -# CONFIG_TCP_CONG_ADVANCED is not set -CONFIG_TCP_CONG_CUBIC=y -CONFIG_DEFAULT_TCP_CONG="cubic" -# CONFIG_TCP_MD5SIG is not set -# CONFIG_IPV6 is not set -# CONFIG_NETWORK_SECMARK is not set -CONFIG_NETFILTER=y -# CONFIG_NETFILTER_DEBUG is not set -CONFIG_NETFILTER_ADVANCED=y - -# -# Core Netfilter Configuration -# -CONFIG_NETFILTER_NETLINK=m -CONFIG_NETFILTER_NETLINK_QUEUE=m -CONFIG_NETFILTER_NETLINK_LOG=m -# CONFIG_NF_CONNTRACK is not set -CONFIG_NETFILTER_XTABLES=m -CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m -# CONFIG_NETFILTER_XT_TARGET_DSCP is not set -CONFIG_NETFILTER_XT_TARGET_MARK=m -# CONFIG_NETFILTER_XT_TARGET_NFLOG is not set -CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m -CONFIG_NETFILTER_XT_TARGET_RATEEST=m -CONFIG_NETFILTER_XT_TARGET_TRACE=m -# CONFIG_NETFILTER_XT_TARGET_TCPMSS is not set -CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m -CONFIG_NETFILTER_XT_MATCH_COMMENT=m -CONFIG_NETFILTER_XT_MATCH_DCCP=m -# CONFIG_NETFILTER_XT_MATCH_DSCP is not set -CONFIG_NETFILTER_XT_MATCH_ESP=m -# CONFIG_NETFILTER_XT_MATCH_HASHLIMIT is not set -CONFIG_NETFILTER_XT_MATCH_IPRANGE=m -CONFIG_NETFILTER_XT_MATCH_LENGTH=m -CONFIG_NETFILTER_XT_MATCH_LIMIT=m -CONFIG_NETFILTER_XT_MATCH_MAC=m -CONFIG_NETFILTER_XT_MATCH_MARK=m -CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m -CONFIG_NETFILTER_XT_MATCH_OWNER=m -# CONFIG_NETFILTER_XT_MATCH_POLICY is not set -CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m -CONFIG_NETFILTER_XT_MATCH_QUOTA=m -CONFIG_NETFILTER_XT_MATCH_RATEEST=m -CONFIG_NETFILTER_XT_MATCH_REALM=m -CONFIG_NETFILTER_XT_MATCH_RECENT=m -# CONFIG_NETFILTER_XT_MATCH_RECENT_PROC_COMPAT is not set -CONFIG_NETFILTER_XT_MATCH_SCTP=m -CONFIG_NETFILTER_XT_MATCH_STATISTIC=m -CONFIG_NETFILTER_XT_MATCH_STRING=m -CONFIG_NETFILTER_XT_MATCH_TCPMSS=m -CONFIG_NETFILTER_XT_MATCH_TIME=m -CONFIG_NETFILTER_XT_MATCH_U32=m -# CONFIG_IP_VS is not set - -# -# IP: Netfilter Configuration -# -# CONFIG_NF_DEFRAG_IPV4 is not set -CONFIG_IP_NF_QUEUE=m -CONFIG_IP_NF_IPTABLES=m -CONFIG_IP_NF_MATCH_ADDRTYPE=m -CONFIG_IP_NF_MATCH_AH=m -CONFIG_IP_NF_MATCH_ECN=m -CONFIG_IP_NF_MATCH_TTL=m -CONFIG_IP_NF_FILTER=m -CONFIG_IP_NF_TARGET_REJECT=m -CONFIG_IP_NF_TARGET_LOG=m -CONFIG_IP_NF_TARGET_ULOG=m -CONFIG_IP_NF_MANGLE=m -CONFIG_IP_NF_TARGET_ECN=m -CONFIG_IP_NF_TARGET_TTL=m -CONFIG_IP_NF_RAW=m -CONFIG_IP_NF_ARPTABLES=m -CONFIG_IP_NF_ARPFILTER=m -CONFIG_IP_NF_ARP_MANGLE=m -# CONFIG_IP_DCCP is not set -# CONFIG_IP_SCTP is not set -# CONFIG_TIPC is not set -# CONFIG_ATM is not set -# CONFIG_BRIDGE is not set -# CONFIG_NET_DSA is not set -# CONFIG_VLAN_8021Q is not set -# CONFIG_DECNET is not set -# CONFIG_LLC2 is not set -# CONFIG_IPX is not set -# CONFIG_ATALK is not set -# CONFIG_X25 is not set -# CONFIG_LAPB is not set -# CONFIG_ECONET is not set -# CONFIG_WAN_ROUTER is not set -# CONFIG_NET_SCHED is not set -CONFIG_NET_CLS_ROUTE=y - -# -# Network testing -# -# CONFIG_NET_PKTGEN is not set -# CONFIG_HAMRADIO is not set -# CONFIG_CAN is not set -# CONFIG_IRDA is not set -# CONFIG_BT is not set -# CONFIG_AF_RXRPC is not set -CONFIG_PHONET=m -CONFIG_WIRELESS=y -# CONFIG_CFG80211 is not set -CONFIG_WIRELESS_OLD_REGULATORY=y -CONFIG_WIRELESS_EXT=y -CONFIG_WIRELESS_EXT_SYSFS=y -# CONFIG_MAC80211 is not set -CONFIG_IEEE80211=m -# CONFIG_IEEE80211_DEBUG is not set -CONFIG_IEEE80211_CRYPT_WEP=m -# CONFIG_IEEE80211_CRYPT_CCMP is not set -# CONFIG_IEEE80211_CRYPT_TKIP is not set -# CONFIG_RFKILL is not set -CONFIG_NET_9P=m -# CONFIG_NET_9P_DEBUG is not set - -# -# Device Drivers -# - -# -# Generic Driver Options -# -CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" -CONFIG_STANDALONE=y -CONFIG_PREVENT_FIRMWARE_BUILD=y -CONFIG_FW_LOADER=m -CONFIG_FIRMWARE_IN_KERNEL=y -CONFIG_EXTRA_FIRMWARE="" -# CONFIG_SYS_HYPERVISOR is not set -# CONFIG_CONNECTOR is not set -CONFIG_MTD=m -# CONFIG_MTD_DEBUG is not set -# CONFIG_MTD_CONCAT is not set -# CONFIG_MTD_PARTITIONS is not set - -# -# User Modules And Translation Layers -# -CONFIG_MTD_CHAR=m -CONFIG_MTD_BLKDEVS=m -CONFIG_MTD_BLOCK=m -# CONFIG_MTD_BLOCK_RO is not set -# CONFIG_FTL is not set -# CONFIG_NFTL is not set -# CONFIG_INFTL is not set -# CONFIG_RFD_FTL is not set -# CONFIG_SSFDC is not set -# CONFIG_MTD_OOPS is not set - -# -# RAM/ROM/Flash chip drivers -# -CONFIG_MTD_CFI=m -CONFIG_MTD_JEDECPROBE=m -CONFIG_MTD_GEN_PROBE=m -CONFIG_MTD_CFI_ADV_OPTIONS=y -CONFIG_MTD_CFI_NOSWAP=y -# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set -# CONFIG_MTD_CFI_LE_BYTE_SWAP is not set -# CONFIG_MTD_CFI_GEOMETRY is not set -CONFIG_MTD_MAP_BANK_WIDTH_1=y -CONFIG_MTD_MAP_BANK_WIDTH_2=y -CONFIG_MTD_MAP_BANK_WIDTH_4=y -# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set -# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set -# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set -CONFIG_MTD_CFI_I1=y -CONFIG_MTD_CFI_I2=y -# CONFIG_MTD_CFI_I4 is not set -# CONFIG_MTD_CFI_I8 is not set -# CONFIG_MTD_OTP is not set -# CONFIG_MTD_CFI_INTELEXT is not set -CONFIG_MTD_CFI_AMDSTD=m -CONFIG_MTD_CFI_STAA=m -CONFIG_MTD_CFI_UTIL=m -# CONFIG_MTD_RAM is not set -# CONFIG_MTD_ROM is not set -# CONFIG_MTD_ABSENT is not set - -# -# Mapping drivers for chip access -# -# CONFIG_MTD_COMPLEX_MAPPINGS is not set -CONFIG_MTD_PHYSMAP=m -CONFIG_MTD_PHYSMAP_START=0x1fc00000 -CONFIG_MTD_PHYSMAP_LEN=0x80000 -CONFIG_MTD_PHYSMAP_BANKWIDTH=1 -# CONFIG_MTD_INTEL_VR_NOR is not set -# CONFIG_MTD_PLATRAM is not set - -# -# Self-contained MTD device drivers -# -# CONFIG_MTD_PMC551 is not set -# CONFIG_MTD_SLRAM is not set -# CONFIG_MTD_PHRAM is not set -# CONFIG_MTD_MTDRAM is not set -# CONFIG_MTD_BLOCK2MTD is not set - -# -# Disk-On-Chip Device Drivers -# -# CONFIG_MTD_DOC2000 is not set -# CONFIG_MTD_DOC2001 is not set -# CONFIG_MTD_DOC2001PLUS is not set -# CONFIG_MTD_NAND is not set -# CONFIG_MTD_ONENAND is not set - -# -# UBI - Unsorted block images -# -# CONFIG_MTD_UBI is not set -# CONFIG_PARPORT is not set -# CONFIG_PNP is not set -CONFIG_BLK_DEV=y -# CONFIG_BLK_CPQ_DA is not set -# CONFIG_BLK_CPQ_CISS_DA is not set -# CONFIG_BLK_DEV_DAC960 is not set -# CONFIG_BLK_DEV_UMEM is not set -# CONFIG_BLK_DEV_COW_COMMON is not set -CONFIG_BLK_DEV_LOOP=y -CONFIG_BLK_DEV_CRYPTOLOOP=m -# CONFIG_BLK_DEV_NBD is not set -# CONFIG_BLK_DEV_SX8 is not set -# CONFIG_BLK_DEV_UB is not set -CONFIG_BLK_DEV_RAM=m -CONFIG_BLK_DEV_RAM_COUNT=16 -CONFIG_BLK_DEV_RAM_SIZE=4096 -# CONFIG_BLK_DEV_XIP is not set -CONFIG_CDROM_PKTCDVD=m -CONFIG_CDROM_PKTCDVD_BUFFERS=8 -# CONFIG_CDROM_PKTCDVD_WCACHE is not set -CONFIG_ATA_OVER_ETH=m -# CONFIG_BLK_DEV_HD is not set -# CONFIG_MISC_DEVICES is not set -CONFIG_HAVE_IDE=y -CONFIG_IDE=y - -# -# Please see Documentation/ide/ide.txt for help/info on IDE drives -# -CONFIG_IDE_TIMINGS=y -CONFIG_IDE_ATAPI=y -# CONFIG_BLK_DEV_IDE_SATA is not set -CONFIG_IDE_GD=y -CONFIG_IDE_GD_ATA=y -# CONFIG_IDE_GD_ATAPI is not set -CONFIG_BLK_DEV_IDECD=y -CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS=y -# CONFIG_BLK_DEV_IDETAPE is not set -CONFIG_BLK_DEV_IDESCSI=y -CONFIG_IDE_TASK_IOCTL=y -CONFIG_IDE_PROC_FS=y - -# -# IDE chipset support/bugfixes -# -CONFIG_IDE_GENERIC=y -# CONFIG_BLK_DEV_PLATFORM is not set -CONFIG_BLK_DEV_IDEDMA_SFF=y - -# -# PCI IDE chipsets support -# -CONFIG_BLK_DEV_IDEPCI=y -CONFIG_IDEPCI_PCIBUS_ORDER=y -# CONFIG_BLK_DEV_OFFBOARD is not set -CONFIG_BLK_DEV_GENERIC=y -# CONFIG_BLK_DEV_OPTI621 is not set -CONFIG_BLK_DEV_IDEDMA_PCI=y -# CONFIG_BLK_DEV_AEC62XX is not set -# CONFIG_BLK_DEV_ALI15X3 is not set -# CONFIG_BLK_DEV_AMD74XX is not set -# CONFIG_BLK_DEV_CMD64X is not set -# CONFIG_BLK_DEV_TRIFLEX is not set -# CONFIG_BLK_DEV_CS5520 is not set -# CONFIG_BLK_DEV_CS5530 is not set -# CONFIG_BLK_DEV_HPT366 is not set -# CONFIG_BLK_DEV_JMICRON is not set -# CONFIG_BLK_DEV_SC1200 is not set -# CONFIG_BLK_DEV_PIIX is not set -# CONFIG_BLK_DEV_IT8213 is not set -# CONFIG_BLK_DEV_IT821X is not set -# CONFIG_BLK_DEV_NS87415 is not set -# CONFIG_BLK_DEV_PDC202XX_OLD is not set -# CONFIG_BLK_DEV_PDC202XX_NEW is not set -# CONFIG_BLK_DEV_SVWKS is not set -# CONFIG_BLK_DEV_SIIMAGE is not set -# CONFIG_BLK_DEV_SLC90E66 is not set -# CONFIG_BLK_DEV_TRM290 is not set -CONFIG_BLK_DEV_VIA82CXXX=y -# CONFIG_BLK_DEV_TC86C001 is not set - -# -# Other IDE chipsets support -# - -# -# Note: most of these also require special kernel boot parameters -# -# CONFIG_BLK_DEV_4DRIVES is not set -# CONFIG_BLK_DEV_ALI14XX is not set -# CONFIG_BLK_DEV_DTC2278 is not set -# CONFIG_BLK_DEV_HT6560B is not set -# CONFIG_BLK_DEV_QD65XX is not set -# CONFIG_BLK_DEV_UMC8672 is not set -CONFIG_BLK_DEV_IDEDMA=y - -# -# SCSI device support -# -# CONFIG_RAID_ATTRS is not set -CONFIG_SCSI=y -CONFIG_SCSI_DMA=y -# CONFIG_SCSI_TGT is not set -# CONFIG_SCSI_NETLINK is not set -CONFIG_SCSI_PROC_FS=y - -# -# SCSI support type (disk, tape, CD-ROM) -# -CONFIG_BLK_DEV_SD=y -# CONFIG_CHR_DEV_ST is not set -# CONFIG_CHR_DEV_OSST is not set -CONFIG_BLK_DEV_SR=y -CONFIG_BLK_DEV_SR_VENDOR=y -CONFIG_CHR_DEV_SG=y -# CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# -# CONFIG_SCSI_MULTI_LUN is not set -CONFIG_SCSI_CONSTANTS=y -# CONFIG_SCSI_LOGGING is not set -# CONFIG_SCSI_SCAN_ASYNC is not set -CONFIG_SCSI_WAIT_SCAN=m - -# -# SCSI Transports -# -# CONFIG_SCSI_SPI_ATTRS is not set -# CONFIG_SCSI_FC_ATTRS is not set -# CONFIG_SCSI_ISCSI_ATTRS is not set -# CONFIG_SCSI_SAS_ATTRS is not set -# CONFIG_SCSI_SAS_LIBSAS is not set -# CONFIG_SCSI_SRP_ATTRS is not set -# CONFIG_SCSI_LOWLEVEL is not set -# CONFIG_SCSI_DH is not set -# CONFIG_ATA is not set -# CONFIG_MD is not set -# CONFIG_FUSION is not set - -# -# IEEE 1394 (FireWire) support -# - -# -# Enable only one of the two stacks, unless you know what you are doing -# -# CONFIG_FIREWIRE is not set -# CONFIG_IEEE1394 is not set -# CONFIG_I2O is not set -CONFIG_NETDEVICES=y -# CONFIG_DUMMY is not set -# CONFIG_BONDING is not set -CONFIG_MACVLAN=m -# CONFIG_EQUALIZER is not set -# CONFIG_TUN is not set -CONFIG_VETH=m -# CONFIG_ARCNET is not set -CONFIG_PHYLIB=m - -# -# MII PHY device drivers -# -CONFIG_MARVELL_PHY=m -CONFIG_DAVICOM_PHY=m -CONFIG_QSEMI_PHY=m -CONFIG_LXT_PHY=m -CONFIG_CICADA_PHY=m -# CONFIG_VITESSE_PHY is not set -# CONFIG_SMSC_PHY is not set -# CONFIG_BROADCOM_PHY is not set -# CONFIG_ICPLUS_PHY is not set -# CONFIG_REALTEK_PHY is not set -# CONFIG_MDIO_BITBANG is not set -CONFIG_NET_ETHERNET=y -CONFIG_MII=y -# CONFIG_AX88796 is not set -# CONFIG_HAPPYMEAL is not set -# CONFIG_SUNGEM is not set -# CONFIG_CASSINI is not set -# CONFIG_NET_VENDOR_3COM is not set -# CONFIG_NET_VENDOR_SMC is not set -# CONFIG_SMC91X is not set -# CONFIG_DM9000 is not set -# CONFIG_NET_VENDOR_RACAL is not set -# CONFIG_NET_TULIP is not set -# CONFIG_AT1700 is not set -# CONFIG_DEPCA is not set -# CONFIG_HP100 is not set -# CONFIG_NET_ISA is not set -# CONFIG_IBM_NEW_EMAC_ZMII is not set -# CONFIG_IBM_NEW_EMAC_RGMII is not set -# CONFIG_IBM_NEW_EMAC_TAH is not set -# CONFIG_IBM_NEW_EMAC_EMAC4 is not set -# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set -# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set -# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set -CONFIG_NET_PCI=y -# CONFIG_PCNET32 is not set -# CONFIG_AMD8111_ETH is not set -# CONFIG_ADAPTEC_STARFIRE is not set -# CONFIG_AC3200 is not set -# CONFIG_APRICOT is not set -# CONFIG_B44 is not set -# CONFIG_FORCEDETH is not set -# CONFIG_CS89x0 is not set -# CONFIG_TC35815 is not set -# CONFIG_EEPRO100 is not set -# CONFIG_E100 is not set -# CONFIG_FEALNX is not set -# CONFIG_NATSEMI is not set -# CONFIG_NE2K_PCI is not set -# CONFIG_8139CP is not set -CONFIG_8139TOO=y -# CONFIG_8139TOO_PIO is not set -# CONFIG_8139TOO_TUNE_TWISTER is not set -# CONFIG_8139TOO_8129 is not set -# CONFIG_8139_OLD_RX_RESET is not set -# CONFIG_R6040 is not set -# CONFIG_SIS900 is not set -# CONFIG_EPIC100 is not set -# CONFIG_SUNDANCE is not set -# CONFIG_TLAN is not set -# CONFIG_VIA_RHINE is not set -# CONFIG_SC92031 is not set -# CONFIG_ATL2 is not set -CONFIG_NETDEV_1000=y -# CONFIG_ACENIC is not set -# CONFIG_DL2K is not set -# CONFIG_E1000 is not set -# CONFIG_E1000E is not set -# CONFIG_IP1000 is not set -# CONFIG_IGB is not set -# CONFIG_NS83820 is not set -# CONFIG_HAMACHI is not set -# CONFIG_YELLOWFIN is not set -# CONFIG_R8169 is not set -# CONFIG_SIS190 is not set -# CONFIG_SKGE is not set -# CONFIG_SKY2 is not set -# CONFIG_VIA_VELOCITY is not set -# CONFIG_TIGON3 is not set -# CONFIG_BNX2 is not set -# CONFIG_QLA3XXX is not set -# CONFIG_ATL1 is not set -# CONFIG_ATL1E is not set -# CONFIG_JME is not set -CONFIG_NETDEV_10000=y -# CONFIG_CHELSIO_T1 is not set -# CONFIG_CHELSIO_T3 is not set -# CONFIG_ENIC is not set -# CONFIG_IXGBE is not set -# CONFIG_IXGB is not set -# CONFIG_S2IO is not set -# CONFIG_MYRI10GE is not set -# CONFIG_NETXEN_NIC is not set -# CONFIG_NIU is not set -# CONFIG_MLX4_EN is not set -# CONFIG_MLX4_CORE is not set -# CONFIG_TEHUTI is not set -# CONFIG_BNX2X is not set -# CONFIG_QLGE is not set -# CONFIG_SFC is not set -# CONFIG_TR is not set - -# -# Wireless LAN -# -# CONFIG_WLAN_PRE80211 is not set -# CONFIG_WLAN_80211 is not set -# CONFIG_IWLWIFI_LEDS is not set - -# -# USB Network Adapters -# -# CONFIG_USB_CATC is not set -# CONFIG_USB_KAWETH is not set -# CONFIG_USB_PEGASUS is not set -# CONFIG_USB_RTL8150 is not set -# CONFIG_USB_USBNET is not set -# CONFIG_WAN is not set -# CONFIG_FDDI is not set -# CONFIG_HIPPI is not set -CONFIG_PPP=m -CONFIG_PPP_MULTILINK=y -CONFIG_PPP_FILTER=y -CONFIG_PPP_ASYNC=m -CONFIG_PPP_SYNC_TTY=m -CONFIG_PPP_DEFLATE=m -CONFIG_PPP_BSDCOMP=m -CONFIG_PPP_MPPE=m -CONFIG_PPPOE=m -CONFIG_PPPOL2TP=m -CONFIG_SLIP=m -CONFIG_SLIP_COMPRESSED=y -CONFIG_SLHC=m -CONFIG_SLIP_SMART=y -CONFIG_SLIP_MODE_SLIP6=y -CONFIG_NET_FC=y -# CONFIG_NETCONSOLE is not set -# CONFIG_NETPOLL is not set -# CONFIG_NET_POLL_CONTROLLER is not set -# CONFIG_ISDN is not set -# CONFIG_PHONE is not set - -# -# Input device support -# -CONFIG_INPUT=y -CONFIG_INPUT_FF_MEMLESS=y -# CONFIG_INPUT_POLLDEV is not set - -# -# Userland interfaces -# -CONFIG_INPUT_MOUSEDEV=y -CONFIG_INPUT_MOUSEDEV_PSAUX=y -CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 -CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 -# CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_EVDEV is not set -# CONFIG_INPUT_EVBUG is not set - -# -# Input Device Drivers -# -CONFIG_INPUT_KEYBOARD=y -CONFIG_KEYBOARD_ATKBD=m -# CONFIG_KEYBOARD_SUNKBD is not set -# CONFIG_KEYBOARD_LKKBD is not set -# CONFIG_KEYBOARD_XTKBD is not set -# CONFIG_KEYBOARD_NEWTON is not set -# CONFIG_KEYBOARD_STOWAWAY is not set -CONFIG_INPUT_MOUSE=y -CONFIG_MOUSE_PS2=y -CONFIG_MOUSE_PS2_ALPS=y -CONFIG_MOUSE_PS2_LOGIPS2PP=y -CONFIG_MOUSE_PS2_SYNAPTICS=y -CONFIG_MOUSE_PS2_LIFEBOOK=y -CONFIG_MOUSE_PS2_TRACKPOINT=y -# CONFIG_MOUSE_PS2_ELANTECH is not set -# CONFIG_MOUSE_PS2_TOUCHKIT is not set -CONFIG_MOUSE_SERIAL=y -# CONFIG_MOUSE_APPLETOUCH is not set -# CONFIG_MOUSE_BCM5974 is not set -# CONFIG_MOUSE_INPORT is not set -# CONFIG_MOUSE_LOGIBM is not set -# CONFIG_MOUSE_PC110PAD is not set -# CONFIG_MOUSE_VSXXXAA is not set -# CONFIG_INPUT_JOYSTICK is not set -# CONFIG_INPUT_TABLET is not set -# CONFIG_INPUT_TOUCHSCREEN is not set -# CONFIG_INPUT_MISC is not set - -# -# Hardware I/O ports -# -CONFIG_SERIO=y -CONFIG_SERIO_I8042=y -CONFIG_SERIO_SERPORT=y -# CONFIG_SERIO_PCIPS2 is not set -CONFIG_SERIO_LIBPS2=y -# CONFIG_SERIO_RAW is not set -# CONFIG_GAMEPORT is not set - -# -# Character devices -# -CONFIG_VT=y -CONFIG_CONSOLE_TRANSLATIONS=y -CONFIG_VT_CONSOLE=y -CONFIG_HW_CONSOLE=y -# CONFIG_VT_HW_CONSOLE_BINDING is not set -CONFIG_DEVKMEM=y -# CONFIG_SERIAL_NONSTANDARD is not set -# CONFIG_NOZOMI is not set - -# -# Serial drivers -# -CONFIG_SERIAL_8250=y -CONFIG_SERIAL_8250_CONSOLE=y -CONFIG_SERIAL_8250_PCI=y -CONFIG_SERIAL_8250_NR_UARTS=2 -CONFIG_SERIAL_8250_RUNTIME_UARTS=2 -# CONFIG_SERIAL_8250_EXTENDED is not set - -# -# Non-8250 serial port support -# -CONFIG_SERIAL_CORE=y -CONFIG_SERIAL_CORE_CONSOLE=y -# CONFIG_SERIAL_JSM is not set -CONFIG_UNIX98_PTYS=y -CONFIG_LEGACY_PTYS=y -CONFIG_LEGACY_PTY_COUNT=256 -# CONFIG_IPMI_HANDLER is not set -CONFIG_HW_RANDOM=y -# CONFIG_DTLK is not set -# CONFIG_R3964 is not set -# CONFIG_APPLICOM is not set -# CONFIG_RAW_DRIVER is not set -# CONFIG_TCG_TPM is not set -CONFIG_DEVPORT=y -CONFIG_I2C=m -CONFIG_I2C_BOARDINFO=y -CONFIG_I2C_CHARDEV=m -CONFIG_I2C_HELPER_AUTO=y - -# -# I2C Hardware Bus support -# - -# -# PC SMBus host controller drivers -# -# CONFIG_I2C_ALI1535 is not set -# CONFIG_I2C_ALI1563 is not set -# CONFIG_I2C_ALI15X3 is not set -# CONFIG_I2C_AMD756 is not set -# CONFIG_I2C_AMD8111 is not set -# CONFIG_I2C_I801 is not set -# CONFIG_I2C_ISCH is not set -# CONFIG_I2C_PIIX4 is not set -# CONFIG_I2C_NFORCE2 is not set -# CONFIG_I2C_SIS5595 is not set -# CONFIG_I2C_SIS630 is not set -# CONFIG_I2C_SIS96X is not set -# CONFIG_I2C_VIA is not set -CONFIG_I2C_VIAPRO=m - -# -# I2C system bus drivers (mostly embedded / system-on-chip) -# -# CONFIG_I2C_OCORES is not set -# CONFIG_I2C_SIMTEC is not set - -# -# External I2C/SMBus adapter drivers -# -# CONFIG_I2C_PARPORT_LIGHT is not set -# CONFIG_I2C_TAOS_EVM is not set -# CONFIG_I2C_TINY_USB is not set - -# -# Graphics adapter I2C/DDC channel drivers -# -# CONFIG_I2C_VOODOO3 is not set - -# -# Other I2C/SMBus bus drivers -# -# CONFIG_I2C_ELEKTOR is not set -# CONFIG_I2C_PCA_ISA is not set -# CONFIG_I2C_PCA_PLATFORM is not set -# CONFIG_I2C_STUB is not set - -# -# Miscellaneous I2C Chip support -# -# CONFIG_DS1682 is not set -# CONFIG_EEPROM_AT24 is not set -# CONFIG_EEPROM_LEGACY is not set -# CONFIG_SENSORS_PCF8574 is not set -# CONFIG_PCF8575 is not set -# CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_PCF8591 is not set -# CONFIG_SENSORS_MAX6875 is not set -# CONFIG_SENSORS_TSL2550 is not set -# CONFIG_I2C_DEBUG_CORE is not set -# CONFIG_I2C_DEBUG_ALGO is not set -# CONFIG_I2C_DEBUG_BUS is not set -# CONFIG_I2C_DEBUG_CHIP is not set -# CONFIG_SPI is not set -# CONFIG_W1 is not set -# CONFIG_POWER_SUPPLY is not set -# CONFIG_HWMON is not set -# CONFIG_THERMAL is not set -# CONFIG_THERMAL_HWMON is not set -# CONFIG_WATCHDOG is not set -CONFIG_SSB_POSSIBLE=y - -# -# Sonics Silicon Backplane -# -# CONFIG_SSB is not set - -# -# Multifunction device drivers -# -# CONFIG_MFD_CORE is not set -# CONFIG_MFD_SM501 is not set -# CONFIG_HTC_PASIC3 is not set -# CONFIG_MFD_TMIO is not set -# CONFIG_MFD_WM8400 is not set -# CONFIG_MFD_WM8350_I2C is not set -# CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -CONFIG_VIDEO_DEV=m -CONFIG_VIDEO_V4L2_COMMON=m -CONFIG_VIDEO_ALLOW_V4L1=y -CONFIG_VIDEO_V4L1_COMPAT=y -# CONFIG_DVB_CORE is not set -CONFIG_VIDEO_MEDIA=m - -# -# Multimedia drivers -# -CONFIG_MEDIA_ATTACH=y -CONFIG_MEDIA_TUNER=m -CONFIG_MEDIA_TUNER_CUSTOMIZE=y -CONFIG_MEDIA_TUNER_SIMPLE=m -CONFIG_MEDIA_TUNER_TDA8290=m -CONFIG_MEDIA_TUNER_TDA827X=m -CONFIG_MEDIA_TUNER_TDA18271=m -CONFIG_MEDIA_TUNER_TDA9887=m -CONFIG_MEDIA_TUNER_TEA5761=m -CONFIG_MEDIA_TUNER_TEA5767=m -CONFIG_MEDIA_TUNER_MT20XX=m -CONFIG_MEDIA_TUNER_MT2060=m -CONFIG_MEDIA_TUNER_MT2266=m -CONFIG_MEDIA_TUNER_MT2131=m -CONFIG_MEDIA_TUNER_QT1010=m -CONFIG_MEDIA_TUNER_XC2028=m -CONFIG_MEDIA_TUNER_XC5000=m -CONFIG_MEDIA_TUNER_MXL5005S=m -CONFIG_MEDIA_TUNER_MXL5007T=m -CONFIG_VIDEO_V4L2=m -CONFIG_VIDEO_V4L1=m -CONFIG_VIDEOBUF_GEN=m -CONFIG_VIDEOBUF_VMALLOC=m -CONFIG_VIDEOBUF_DMA_CONTIG=m -CONFIG_VIDEO_CAPTURE_DRIVERS=y -# CONFIG_VIDEO_ADV_DEBUG is not set -# CONFIG_VIDEO_FIXED_MINOR_RANGES is not set -CONFIG_VIDEO_HELPER_CHIPS_AUTO=y -# CONFIG_VIDEO_VIVI is not set -# CONFIG_VIDEO_BT848 is not set -# CONFIG_VIDEO_PMS is not set -# CONFIG_VIDEO_CPIA is not set -# CONFIG_VIDEO_CPIA2 is not set -# CONFIG_VIDEO_SAA5246A is not set -# CONFIG_VIDEO_SAA5249 is not set -# CONFIG_VIDEO_STRADIS is not set -# CONFIG_VIDEO_SAA7134 is not set -# CONFIG_VIDEO_MXB is not set -# CONFIG_VIDEO_HEXIUM_ORION is not set -# CONFIG_VIDEO_HEXIUM_GEMINI is not set -# CONFIG_VIDEO_CX88 is not set -# CONFIG_VIDEO_IVTV is not set -# CONFIG_VIDEO_CAFE_CCIC is not set -CONFIG_SOC_CAMERA=m -CONFIG_SOC_CAMERA_MT9M001=m -CONFIG_SOC_CAMERA_MT9M111=m -CONFIG_SOC_CAMERA_MT9V022=m -CONFIG_SOC_CAMERA_PLATFORM=m -CONFIG_VIDEO_SH_MOBILE_CEU=m -CONFIG_V4L_USB_DRIVERS=y -CONFIG_USB_VIDEO_CLASS=m -CONFIG_USB_VIDEO_CLASS_INPUT_EVDEV=y -CONFIG_USB_GSPCA=m -CONFIG_USB_M5602=m -CONFIG_USB_GSPCA_CONEX=m -CONFIG_USB_GSPCA_ETOMS=m -CONFIG_USB_GSPCA_FINEPIX=m -CONFIG_USB_GSPCA_MARS=m -CONFIG_USB_GSPCA_OV519=m -CONFIG_USB_GSPCA_PAC207=m -CONFIG_USB_GSPCA_PAC7311=m -CONFIG_USB_GSPCA_SONIXB=m -CONFIG_USB_GSPCA_SONIXJ=m -CONFIG_USB_GSPCA_SPCA500=m -CONFIG_USB_GSPCA_SPCA501=m -CONFIG_USB_GSPCA_SPCA505=m -CONFIG_USB_GSPCA_SPCA506=m -CONFIG_USB_GSPCA_SPCA508=m -CONFIG_USB_GSPCA_SPCA561=m -CONFIG_USB_GSPCA_STK014=m -CONFIG_USB_GSPCA_SUNPLUS=m -CONFIG_USB_GSPCA_T613=m -CONFIG_USB_GSPCA_TV8532=m -CONFIG_USB_GSPCA_VC032X=m -CONFIG_USB_GSPCA_ZC3XX=m -# CONFIG_VIDEO_PVRUSB2 is not set -# CONFIG_VIDEO_EM28XX is not set -# CONFIG_VIDEO_USBVISION is not set -CONFIG_VIDEO_USBVIDEO=m -CONFIG_USB_VICAM=m -CONFIG_USB_IBMCAM=m -CONFIG_USB_KONICAWC=m -CONFIG_USB_QUICKCAM_MESSENGER=m -CONFIG_USB_ET61X251=m -# CONFIG_VIDEO_OVCAMCHIP is not set -CONFIG_USB_OV511=m -CONFIG_USB_SE401=m -CONFIG_USB_SN9C102=m -CONFIG_USB_STV680=m -CONFIG_USB_ZC0301=m -CONFIG_USB_PWC=m -# CONFIG_USB_PWC_DEBUG is not set -# CONFIG_USB_ZR364XX is not set -CONFIG_USB_STKWEBCAM=m -CONFIG_USB_S2255=m -CONFIG_RADIO_ADAPTERS=y -# CONFIG_RADIO_CADET is not set -# CONFIG_RADIO_RTRACK is not set -# CONFIG_RADIO_RTRACK2 is not set -# CONFIG_RADIO_AZTECH is not set -# CONFIG_RADIO_GEMTEK is not set -# CONFIG_RADIO_GEMTEK_PCI is not set -# CONFIG_RADIO_MAXIRADIO is not set -# CONFIG_RADIO_MAESTRO is not set -# CONFIG_RADIO_SF16FMI is not set -# CONFIG_RADIO_SF16FMR2 is not set -# CONFIG_RADIO_TERRATEC is not set -# CONFIG_RADIO_TRUST is not set -# CONFIG_RADIO_TYPHOON is not set -# CONFIG_RADIO_ZOLTRIX is not set -# CONFIG_USB_DSBR is not set -CONFIG_USB_SI470X=m -CONFIG_USB_MR800=m -CONFIG_DAB=y -# CONFIG_USB_DABUSB is not set - -# -# Graphics support -# -# CONFIG_DRM is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=m -CONFIG_FB=y -# CONFIG_FIRMWARE_EDID is not set -# CONFIG_FB_DDC is not set -# CONFIG_FB_BOOT_VESA_SUPPORT is not set -CONFIG_FB_CFB_FILLRECT=y -CONFIG_FB_CFB_COPYAREA=y -CONFIG_FB_CFB_IMAGEBLIT=y -# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set -# CONFIG_FB_SYS_FILLRECT is not set -# CONFIG_FB_SYS_COPYAREA is not set -# CONFIG_FB_SYS_IMAGEBLIT is not set -# CONFIG_FB_FOREIGN_ENDIAN is not set -# CONFIG_FB_SYS_FOPS is not set -# CONFIG_FB_SVGALIB is not set -# CONFIG_FB_MACMODES is not set -CONFIG_FB_BACKLIGHT=y -CONFIG_FB_MODE_HELPERS=y -# CONFIG_FB_TILEBLITTING is not set - -# -# Frame buffer hardware drivers -# -# CONFIG_FB_CIRRUS is not set -# CONFIG_FB_PM2 is not set -# CONFIG_FB_CYBER2000 is not set -# CONFIG_FB_ASILIANT is not set -# CONFIG_FB_IMSTT is not set -# CONFIG_FB_S1D13XXX is not set -# CONFIG_FB_NVIDIA is not set -# CONFIG_FB_RIVA is not set -# CONFIG_FB_MATROX is not set -CONFIG_FB_RADEON=y -# CONFIG_FB_RADEON_I2C is not set -CONFIG_FB_RADEON_BACKLIGHT=y -# CONFIG_FB_RADEON_DEBUG is not set -# CONFIG_FB_ATY128 is not set -# CONFIG_FB_ATY is not set -# CONFIG_FB_S3 is not set -# CONFIG_FB_SAVAGE is not set -# CONFIG_FB_SIS is not set -# CONFIG_FB_VIA is not set -# CONFIG_FB_NEOMAGIC is not set -# CONFIG_FB_KYRO is not set -# CONFIG_FB_3DFX is not set -# CONFIG_FB_VOODOO1 is not set -# CONFIG_FB_VT8623 is not set -# CONFIG_FB_TRIDENT is not set -# CONFIG_FB_ARK is not set -# CONFIG_FB_PM3 is not set -# CONFIG_FB_CARMINE is not set -# CONFIG_FB_VIRTUAL is not set -# CONFIG_FB_METRONOME is not set -# CONFIG_FB_MB862XX is not set -CONFIG_BACKLIGHT_LCD_SUPPORT=y -CONFIG_LCD_CLASS_DEVICE=m -# CONFIG_LCD_ILI9320 is not set -# CONFIG_LCD_PLATFORM is not set -CONFIG_BACKLIGHT_CLASS_DEVICE=y -# CONFIG_BACKLIGHT_CORGI is not set - -# -# Display device support -# -# CONFIG_DISPLAY_SUPPORT is not set - -# -# Console display driver support -# -# CONFIG_VGA_CONSOLE is not set -# CONFIG_MDA_CONSOLE is not set -CONFIG_DUMMY_CONSOLE=y -CONFIG_FRAMEBUFFER_CONSOLE=y -# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set -# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set -# CONFIG_FONTS is not set -CONFIG_FONT_8x8=y -CONFIG_FONT_8x16=y -# CONFIG_LOGO is not set -CONFIG_SOUND=y -CONFIG_SOUND_OSS_CORE=y -CONFIG_SND=m -CONFIG_SND_TIMER=m -CONFIG_SND_PCM=m -CONFIG_SND_RAWMIDI=m -CONFIG_SND_SEQUENCER=m -CONFIG_SND_SEQ_DUMMY=m -CONFIG_SND_OSSEMUL=y -CONFIG_SND_MIXER_OSS=m -CONFIG_SND_PCM_OSS=m -CONFIG_SND_PCM_OSS_PLUGINS=y -CONFIG_SND_SEQUENCER_OSS=y -# CONFIG_SND_DYNAMIC_MINORS is not set -CONFIG_SND_SUPPORT_OLD_API=y -CONFIG_SND_VERBOSE_PROCFS=y -# CONFIG_SND_VERBOSE_PRINTK is not set -# CONFIG_SND_DEBUG is not set -CONFIG_SND_VMASTER=y -CONFIG_SND_MPU401_UART=m -CONFIG_SND_AC97_CODEC=m -CONFIG_SND_DRIVERS=y -# CONFIG_SND_DUMMY is not set -# CONFIG_SND_VIRMIDI is not set -# CONFIG_SND_MTPAV is not set -# CONFIG_SND_SERIAL_U16550 is not set -# CONFIG_SND_MPU401 is not set -# CONFIG_SND_AC97_POWER_SAVE is not set -CONFIG_SND_PCI=y -# CONFIG_SND_AD1889 is not set -# CONFIG_SND_ALS300 is not set -# CONFIG_SND_ALI5451 is not set -# CONFIG_SND_ATIIXP is not set -# CONFIG_SND_ATIIXP_MODEM is not set -# CONFIG_SND_AU8810 is not set -# CONFIG_SND_AU8820 is not set -# CONFIG_SND_AU8830 is not set -# CONFIG_SND_AW2 is not set -# CONFIG_SND_AZT3328 is not set -# CONFIG_SND_BT87X is not set -# CONFIG_SND_CA0106 is not set -# CONFIG_SND_CMIPCI is not set -# CONFIG_SND_OXYGEN is not set -# CONFIG_SND_CS4281 is not set -# CONFIG_SND_CS46XX is not set -# CONFIG_SND_DARLA20 is not set -# CONFIG_SND_GINA20 is not set -# CONFIG_SND_LAYLA20 is not set -# CONFIG_SND_DARLA24 is not set -# CONFIG_SND_GINA24 is not set -# CONFIG_SND_LAYLA24 is not set -# CONFIG_SND_MONA is not set -# CONFIG_SND_MIA is not set -# CONFIG_SND_ECHO3G is not set -# CONFIG_SND_INDIGO is not set -# CONFIG_SND_INDIGOIO is not set -# CONFIG_SND_INDIGODJ is not set -# CONFIG_SND_EMU10K1 is not set -# CONFIG_SND_EMU10K1X is not set -# CONFIG_SND_ENS1370 is not set -# CONFIG_SND_ENS1371 is not set -# CONFIG_SND_ES1938 is not set -# CONFIG_SND_ES1968 is not set -# CONFIG_SND_FM801 is not set -# CONFIG_SND_HDA_INTEL is not set -# CONFIG_SND_HDSP is not set -# CONFIG_SND_HDSPM is not set -# CONFIG_SND_HIFIER is not set -# CONFIG_SND_ICE1712 is not set -# CONFIG_SND_ICE1724 is not set -# CONFIG_SND_INTEL8X0 is not set -# CONFIG_SND_INTEL8X0M is not set -# CONFIG_SND_KORG1212 is not set -# CONFIG_SND_MAESTRO3 is not set -# CONFIG_SND_MIXART is not set -# CONFIG_SND_NM256 is not set -# CONFIG_SND_PCXHR is not set -# CONFIG_SND_RIPTIDE is not set -# CONFIG_SND_RME32 is not set -# CONFIG_SND_RME96 is not set -# CONFIG_SND_RME9652 is not set -# CONFIG_SND_SONICVIBES is not set -# CONFIG_SND_TRIDENT is not set -CONFIG_SND_VIA82XX=m -# CONFIG_SND_VIA82XX_MODEM is not set -# CONFIG_SND_VIRTUOSO is not set -# CONFIG_SND_VX222 is not set -# CONFIG_SND_YMFPCI is not set -CONFIG_SND_MIPS=y -CONFIG_SND_USB=y -# CONFIG_SND_USB_AUDIO is not set -# CONFIG_SND_USB_CAIAQ is not set -# CONFIG_SND_SOC is not set -# CONFIG_SOUND_PRIME is not set -CONFIG_AC97_BUS=m -CONFIG_HID_SUPPORT=y -CONFIG_HID=y -# CONFIG_HID_DEBUG is not set -CONFIG_HIDRAW=y - -# -# USB Input Devices -# -CONFIG_USB_HID=m -CONFIG_HID_PID=y -CONFIG_USB_HIDDEV=y - -# -# USB HID Boot Protocol drivers -# -# CONFIG_USB_KBD is not set -# CONFIG_USB_MOUSE is not set - -# -# Special HID drivers -# -CONFIG_HID_COMPAT=y -CONFIG_HID_A4TECH=m -CONFIG_HID_APPLE=m -CONFIG_HID_BELKIN=m -CONFIG_HID_BRIGHT=m -CONFIG_HID_CHERRY=m -CONFIG_HID_CHICONY=m -CONFIG_HID_CYPRESS=m -CONFIG_HID_DELL=m -CONFIG_HID_EZKEY=m -CONFIG_HID_GYRATION=m -CONFIG_HID_LOGITECH=m -CONFIG_LOGITECH_FF=y -CONFIG_LOGIRUMBLEPAD2_FF=y -CONFIG_HID_MICROSOFT=m -CONFIG_HID_MONTEREY=m -CONFIG_HID_PANTHERLORD=m -# CONFIG_PANTHERLORD_FF is not set -CONFIG_HID_PETALYNX=m -CONFIG_HID_SAMSUNG=m -CONFIG_HID_SONY=m -CONFIG_HID_SUNPLUS=m -# CONFIG_THRUSTMASTER_FF is not set -CONFIG_ZEROPLUS_FF=m -CONFIG_USB_SUPPORT=y -CONFIG_USB_ARCH_HAS_HCD=y -CONFIG_USB_ARCH_HAS_OHCI=y -CONFIG_USB_ARCH_HAS_EHCI=y -CONFIG_USB=y -# CONFIG_USB_DEBUG is not set -CONFIG_USB_ANNOUNCE_NEW_DEVICES=y - -# -# Miscellaneous USB options -# -CONFIG_USB_DEVICEFS=y -# CONFIG_USB_DEVICE_CLASS is not set -# CONFIG_USB_DYNAMIC_MINORS is not set -# CONFIG_USB_SUSPEND is not set -# CONFIG_USB_OTG is not set -CONFIG_USB_OTG_WHITELIST=y -# CONFIG_USB_OTG_BLACKLIST_HUB is not set -# CONFIG_USB_MON is not set -# CONFIG_USB_WUSB is not set -CONFIG_USB_WUSB_CBAF=m -# CONFIG_USB_WUSB_CBAF_DEBUG is not set - -# -# USB Host Controller Drivers -# -CONFIG_USB_C67X00_HCD=m -CONFIG_USB_EHCI_HCD=y -CONFIG_USB_EHCI_ROOT_HUB_TT=y -CONFIG_USB_EHCI_TT_NEWSCHED=y -# CONFIG_USB_ISP116X_HCD is not set -CONFIG_USB_ISP1760_HCD=m -CONFIG_USB_OHCI_HCD=y -# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set -# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set -CONFIG_USB_OHCI_LITTLE_ENDIAN=y -CONFIG_USB_UHCI_HCD=m -# CONFIG_USB_SL811_HCD is not set -CONFIG_USB_R8A66597_HCD=m -# CONFIG_USB_WHCI_HCD is not set -# CONFIG_USB_HWA_HCD is not set - -# -# USB Device Class drivers -# -CONFIG_USB_ACM=y -CONFIG_USB_PRINTER=y -CONFIG_USB_WDM=m -CONFIG_USB_TMC=m - -# -# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may also be needed; -# - -# -# see USB_STORAGE Help for more information -# -CONFIG_USB_STORAGE=y -# CONFIG_USB_STORAGE_DEBUG is not set -# CONFIG_USB_STORAGE_DATAFAB is not set -# CONFIG_USB_STORAGE_FREECOM is not set -# CONFIG_USB_STORAGE_ISD200 is not set -# CONFIG_USB_STORAGE_DPCM is not set -# CONFIG_USB_STORAGE_USBAT is not set -# CONFIG_USB_STORAGE_SDDR09 is not set -# CONFIG_USB_STORAGE_SDDR55 is not set -# CONFIG_USB_STORAGE_JUMPSHOT is not set -# CONFIG_USB_STORAGE_ALAUDA is not set -CONFIG_USB_STORAGE_ONETOUCH=y -# CONFIG_USB_STORAGE_KARMA is not set -CONFIG_USB_STORAGE_CYPRESS_ATACB=y -CONFIG_USB_LIBUSUAL=y - -# -# USB Imaging devices -# -# CONFIG_USB_MDC800 is not set -# CONFIG_USB_MICROTEK is not set - -# -# USB port drivers -# -# CONFIG_USB_SERIAL is not set - -# -# USB Miscellaneous drivers -# -# CONFIG_USB_EMI62 is not set -# CONFIG_USB_EMI26 is not set -# CONFIG_USB_ADUTUX is not set -CONFIG_USB_SEVSEG=m -# CONFIG_USB_RIO500 is not set -# CONFIG_USB_LEGOTOWER is not set -# CONFIG_USB_LCD is not set -# CONFIG_USB_BERRY_CHARGE is not set -# CONFIG_USB_LED is not set -# CONFIG_USB_CYPRESS_CY7C63 is not set -# CONFIG_USB_CYTHERM is not set -# CONFIG_USB_PHIDGET is not set -# CONFIG_USB_IDMOUSE is not set -# CONFIG_USB_FTDI_ELAN is not set -# CONFIG_USB_APPLEDISPLAY is not set -# CONFIG_USB_SISUSBVGA is not set -# CONFIG_USB_LD is not set -# CONFIG_USB_TRANCEVIBRATOR is not set -# CONFIG_USB_IOWARRIOR is not set -# CONFIG_USB_TEST is not set -CONFIG_USB_ISIGHTFW=m -CONFIG_USB_VST=m -# CONFIG_USB_GADGET is not set -# CONFIG_UWB is not set -# CONFIG_MMC is not set -# CONFIG_MEMSTICK is not set -# CONFIG_NEW_LEDS is not set -# CONFIG_ACCESSIBILITY is not set -# CONFIG_INFINIBAND is not set -CONFIG_RTC_LIB=y -CONFIG_RTC_CLASS=m - -# -# RTC interfaces -# -CONFIG_RTC_INTF_SYSFS=y -CONFIG_RTC_INTF_PROC=y -CONFIG_RTC_INTF_DEV=y -CONFIG_RTC_INTF_DEV_UIE_EMUL=y -# CONFIG_RTC_DRV_TEST is not set - -# -# I2C RTC drivers -# -# CONFIG_RTC_DRV_DS1307 is not set -# CONFIG_RTC_DRV_DS1374 is not set -# CONFIG_RTC_DRV_DS1672 is not set -# CONFIG_RTC_DRV_MAX6900 is not set -# CONFIG_RTC_DRV_RS5C372 is not set -# CONFIG_RTC_DRV_ISL1208 is not set -# CONFIG_RTC_DRV_X1205 is not set -# CONFIG_RTC_DRV_PCF8563 is not set -# CONFIG_RTC_DRV_PCF8583 is not set -# CONFIG_RTC_DRV_M41T80 is not set -# CONFIG_RTC_DRV_S35390A is not set -# CONFIG_RTC_DRV_FM3130 is not set -# CONFIG_RTC_DRV_RX8581 is not set - -# -# SPI RTC drivers -# - -# -# Platform RTC drivers -# -CONFIG_RTC_DRV_CMOS=m -# CONFIG_RTC_DRV_DS1286 is not set -# CONFIG_RTC_DRV_DS1511 is not set -# CONFIG_RTC_DRV_DS1553 is not set -# CONFIG_RTC_DRV_DS1742 is not set -# CONFIG_RTC_DRV_STK17TA8 is not set -# CONFIG_RTC_DRV_M48T86 is not set -# CONFIG_RTC_DRV_M48T35 is not set -# CONFIG_RTC_DRV_M48T59 is not set -# CONFIG_RTC_DRV_BQ4802 is not set -# CONFIG_RTC_DRV_V3020 is not set - -# -# on-CPU RTC drivers -# -# CONFIG_DMADEVICES is not set -CONFIG_UIO=m -CONFIG_UIO_CIF=m -# CONFIG_UIO_PDRV is not set -# CONFIG_UIO_PDRV_GENIRQ is not set -# CONFIG_UIO_SMX is not set -# CONFIG_UIO_SERCOS3 is not set -# CONFIG_STAGING is not set -CONFIG_STAGING_EXCLUDE_BUILD=y - -# -# File systems -# -CONFIG_EXT2_FS=y -# CONFIG_EXT2_FS_XATTR is not set -CONFIG_EXT2_FS_XIP=y -CONFIG_EXT3_FS=y -# CONFIG_EXT3_FS_XATTR is not set -CONFIG_EXT4_FS=m -CONFIG_EXT4DEV_COMPAT=y -CONFIG_EXT4_FS_XATTR=y -CONFIG_EXT4_FS_POSIX_ACL=y -CONFIG_EXT4_FS_SECURITY=y -CONFIG_FS_XIP=y -CONFIG_JBD=y -CONFIG_JBD2=m -CONFIG_FS_MBCACHE=m -CONFIG_REISERFS_FS=m -# CONFIG_REISERFS_CHECK is not set -# CONFIG_REISERFS_PROC_INFO is not set -# CONFIG_REISERFS_FS_XATTR is not set -# CONFIG_JFS_FS is not set -CONFIG_FS_POSIX_ACL=y -CONFIG_FILE_LOCKING=y -# CONFIG_XFS_FS is not set -# CONFIG_GFS2_FS is not set -# CONFIG_OCFS2_FS is not set -CONFIG_DNOTIFY=y -CONFIG_INOTIFY=y -CONFIG_INOTIFY_USER=y -# CONFIG_QUOTA is not set -CONFIG_AUTOFS_FS=y -CONFIG_AUTOFS4_FS=y -CONFIG_FUSE_FS=y - -# -# CD-ROM/DVD Filesystems -# -CONFIG_ISO9660_FS=m -CONFIG_JOLIET=y -CONFIG_ZISOFS=y -CONFIG_UDF_FS=m -CONFIG_UDF_NLS=y - -# -# DOS/FAT/NT Filesystems -# -CONFIG_FAT_FS=m -CONFIG_MSDOS_FS=m -CONFIG_VFAT_FS=m -CONFIG_FAT_DEFAULT_CODEPAGE=936 -CONFIG_FAT_DEFAULT_IOCHARSET="utf8" -CONFIG_NTFS_FS=m -# CONFIG_NTFS_DEBUG is not set -CONFIG_NTFS_RW=y - -# -# Pseudo filesystems -# -CONFIG_PROC_FS=y -CONFIG_PROC_KCORE=y -CONFIG_PROC_SYSCTL=y -CONFIG_PROC_PAGE_MONITOR=y -CONFIG_SYSFS=y -CONFIG_TMPFS=y -# CONFIG_TMPFS_POSIX_ACL is not set -# CONFIG_HUGETLB_PAGE is not set -# CONFIG_CONFIGFS_FS is not set - -# -# Miscellaneous filesystems -# -# CONFIG_ADFS_FS is not set -# CONFIG_AFFS_FS is not set -# CONFIG_HFS_FS is not set -# CONFIG_HFSPLUS_FS is not set -# CONFIG_BEFS_FS is not set -# CONFIG_BFS_FS is not set -# CONFIG_EFS_FS is not set -# CONFIG_JFFS2_FS is not set -# CONFIG_CRAMFS is not set -# CONFIG_VXFS_FS is not set -# CONFIG_MINIX_FS is not set -CONFIG_OMFS_FS=m -# CONFIG_HPFS_FS is not set -# CONFIG_QNX4FS_FS is not set -# CONFIG_ROMFS_FS is not set -# CONFIG_SYSV_FS is not set -# CONFIG_UFS_FS is not set -CONFIG_NETWORK_FILESYSTEMS=y -CONFIG_NFS_FS=m -CONFIG_NFS_V3=y -CONFIG_NFS_V3_ACL=y -CONFIG_NFS_V4=y -CONFIG_NFSD=m -CONFIG_NFSD_V2_ACL=y -CONFIG_NFSD_V3=y -CONFIG_NFSD_V3_ACL=y -CONFIG_NFSD_V4=y -CONFIG_LOCKD=m -CONFIG_LOCKD_V4=y -CONFIG_EXPORTFS=m -CONFIG_NFS_ACL_SUPPORT=m -CONFIG_NFS_COMMON=y -CONFIG_SUNRPC=m -CONFIG_SUNRPC_GSS=m -# CONFIG_SUNRPC_REGISTER_V4 is not set -CONFIG_RPCSEC_GSS_KRB5=m -# CONFIG_RPCSEC_GSS_SPKM3 is not set -CONFIG_SMB_FS=m -CONFIG_SMB_NLS_DEFAULT=y -CONFIG_SMB_NLS_REMOTE="cp936" -CONFIG_CIFS=m -CONFIG_CIFS_STATS=y -CONFIG_CIFS_STATS2=y -CONFIG_CIFS_WEAK_PW_HASH=y -CONFIG_CIFS_XATTR=y -CONFIG_CIFS_POSIX=y -CONFIG_CIFS_DEBUG2=y -CONFIG_CIFS_EXPERIMENTAL=y -# CONFIG_NCP_FS is not set -# CONFIG_CODA_FS is not set -# CONFIG_AFS_FS is not set -# CONFIG_9P_FS is not set - -# -# Partition Types -# -CONFIG_PARTITION_ADVANCED=y -# CONFIG_ACORN_PARTITION is not set -# CONFIG_OSF_PARTITION is not set -# CONFIG_AMIGA_PARTITION is not set -# CONFIG_ATARI_PARTITION is not set -# CONFIG_MAC_PARTITION is not set -CONFIG_MSDOS_PARTITION=y -# CONFIG_BSD_DISKLABEL is not set -# CONFIG_MINIX_SUBPARTITION is not set -# CONFIG_SOLARIS_X86_PARTITION is not set -# CONFIG_UNIXWARE_DISKLABEL is not set -# CONFIG_LDM_PARTITION is not set -# CONFIG_SGI_PARTITION is not set -# CONFIG_ULTRIX_PARTITION is not set -# CONFIG_SUN_PARTITION is not set -# CONFIG_KARMA_PARTITION is not set -# CONFIG_EFI_PARTITION is not set -# CONFIG_SYSV68_PARTITION is not set -CONFIG_NLS=y -CONFIG_NLS_DEFAULT="utf8" -# CONFIG_NLS_CODEPAGE_437 is not set -# CONFIG_NLS_CODEPAGE_737 is not set -# CONFIG_NLS_CODEPAGE_775 is not set -# CONFIG_NLS_CODEPAGE_850 is not set -# CONFIG_NLS_CODEPAGE_852 is not set -# CONFIG_NLS_CODEPAGE_855 is not set -# CONFIG_NLS_CODEPAGE_857 is not set -# CONFIG_NLS_CODEPAGE_860 is not set -# CONFIG_NLS_CODEPAGE_861 is not set -# CONFIG_NLS_CODEPAGE_862 is not set -# CONFIG_NLS_CODEPAGE_863 is not set -# CONFIG_NLS_CODEPAGE_864 is not set -# CONFIG_NLS_CODEPAGE_865 is not set -# CONFIG_NLS_CODEPAGE_866 is not set -# CONFIG_NLS_CODEPAGE_869 is not set -CONFIG_NLS_CODEPAGE_936=y -# CONFIG_NLS_CODEPAGE_950 is not set -# CONFIG_NLS_CODEPAGE_932 is not set -# CONFIG_NLS_CODEPAGE_949 is not set -# CONFIG_NLS_CODEPAGE_874 is not set -# CONFIG_NLS_ISO8859_8 is not set -# CONFIG_NLS_CODEPAGE_1250 is not set -# CONFIG_NLS_CODEPAGE_1251 is not set -# CONFIG_NLS_ASCII is not set -CONFIG_NLS_ISO8859_1=y -# CONFIG_NLS_ISO8859_2 is not set -# CONFIG_NLS_ISO8859_3 is not set -# CONFIG_NLS_ISO8859_4 is not set -# CONFIG_NLS_ISO8859_5 is not set -# CONFIG_NLS_ISO8859_6 is not set -# CONFIG_NLS_ISO8859_7 is not set -# CONFIG_NLS_ISO8859_9 is not set -# CONFIG_NLS_ISO8859_13 is not set -# CONFIG_NLS_ISO8859_14 is not set -# CONFIG_NLS_ISO8859_15 is not set -# CONFIG_NLS_KOI8_R is not set -# CONFIG_NLS_KOI8_U is not set -CONFIG_NLS_UTF8=y -# CONFIG_DLM is not set - -# -# Kernel hacking -# -CONFIG_TRACE_IRQFLAGS_SUPPORT=y -# CONFIG_PRINTK_TIME is not set -CONFIG_ENABLE_WARN_DEPRECATED=y -# CONFIG_ENABLE_MUST_CHECK is not set -CONFIG_FRAME_WARN=2048 -# CONFIG_MAGIC_SYSRQ is not set -# CONFIG_UNUSED_SYMBOLS is not set -# CONFIG_DEBUG_FS is not set -# CONFIG_HEADERS_CHECK is not set -# CONFIG_DEBUG_KERNEL is not set -# CONFIG_DEBUG_MEMORY_INIT is not set -# CONFIG_RCU_CPU_STALL_DETECTOR is not set -CONFIG_SYSCTL_SYSCALL_CHECK=y - -# -# Tracers -# -CONFIG_DYNAMIC_PRINTK_DEBUG=y -# CONFIG_SAMPLES is not set -CONFIG_HAVE_ARCH_KGDB=y -CONFIG_CMDLINE="" - -# -# Security options -# -# CONFIG_KEYS is not set -# CONFIG_SECURITY is not set -# CONFIG_SECURITYFS is not set -CONFIG_SECURITY_FILE_CAPABILITIES=y -CONFIG_CRYPTO=y - -# -# Crypto core or helper -# -CONFIG_CRYPTO_FIPS=y -CONFIG_CRYPTO_ALGAPI=y -CONFIG_CRYPTO_AEAD=y -CONFIG_CRYPTO_BLKCIPHER=y -CONFIG_CRYPTO_HASH=y -CONFIG_CRYPTO_RNG=y -CONFIG_CRYPTO_MANAGER=y -CONFIG_CRYPTO_GF128MUL=m -# CONFIG_CRYPTO_NULL is not set -# CONFIG_CRYPTO_CRYPTD is not set -CONFIG_CRYPTO_AUTHENC=m -# CONFIG_CRYPTO_TEST is not set - -# -# Authenticated Encryption with Associated Data -# -CONFIG_CRYPTO_CCM=m -CONFIG_CRYPTO_GCM=m -CONFIG_CRYPTO_SEQIV=m - -# -# Block modes -# -CONFIG_CRYPTO_CBC=m -CONFIG_CRYPTO_CTR=m -CONFIG_CRYPTO_CTS=m -CONFIG_CRYPTO_ECB=m -# CONFIG_CRYPTO_LRW is not set -CONFIG_CRYPTO_PCBC=m -CONFIG_CRYPTO_XTS=m - -# -# Hash modes -# -CONFIG_CRYPTO_HMAC=y -# CONFIG_CRYPTO_XCBC is not set - -# -# Digest -# -# CONFIG_CRYPTO_CRC32C is not set -# CONFIG_CRYPTO_MD4 is not set -CONFIG_CRYPTO_MD5=m -# CONFIG_CRYPTO_MICHAEL_MIC is not set -CONFIG_CRYPTO_RMD128=m -CONFIG_CRYPTO_RMD160=m -CONFIG_CRYPTO_RMD256=m -CONFIG_CRYPTO_RMD320=m -CONFIG_CRYPTO_SHA1=m -# CONFIG_CRYPTO_SHA256 is not set -# CONFIG_CRYPTO_SHA512 is not set -# CONFIG_CRYPTO_TGR192 is not set -# CONFIG_CRYPTO_WP512 is not set - -# -# Ciphers -# -CONFIG_CRYPTO_AES=m -# CONFIG_CRYPTO_ANUBIS is not set -CONFIG_CRYPTO_ARC4=m -# CONFIG_CRYPTO_BLOWFISH is not set -# CONFIG_CRYPTO_CAMELLIA is not set -# CONFIG_CRYPTO_CAST5 is not set -# CONFIG_CRYPTO_CAST6 is not set -CONFIG_CRYPTO_DES=m -# CONFIG_CRYPTO_FCRYPT is not set -# CONFIG_CRYPTO_KHAZAD is not set -CONFIG_CRYPTO_SALSA20=m -CONFIG_CRYPTO_SEED=m -# CONFIG_CRYPTO_SERPENT is not set -# CONFIG_CRYPTO_TEA is not set -# CONFIG_CRYPTO_TWOFISH is not set - -# -# Compression -# -CONFIG_CRYPTO_DEFLATE=m -CONFIG_CRYPTO_LZO=m - -# -# Random Number Generation -# -CONFIG_CRYPTO_ANSI_CPRNG=m -# CONFIG_CRYPTO_HW is not set - -# -# Library routines -# -CONFIG_BITREVERSE=y -CONFIG_CRC_CCITT=y -CONFIG_CRC16=m -# CONFIG_CRC_T10DIF is not set -CONFIG_CRC_ITU_T=m -CONFIG_CRC32=y -CONFIG_CRC7=m -# CONFIG_LIBCRC32C is not set -CONFIG_ZLIB_INFLATE=m -CONFIG_ZLIB_DEFLATE=m -CONFIG_LZO_COMPRESS=m -CONFIG_LZO_DECOMPRESS=m -CONFIG_TEXTSEARCH=y -CONFIG_TEXTSEARCH_KMP=m -CONFIG_TEXTSEARCH_BM=m -CONFIG_TEXTSEARCH_FSM=m -CONFIG_PLIST=y -CONFIG_HAS_IOMEM=y -CONFIG_HAS_IOPORT=y -CONFIG_HAS_DMA=y
arch/mips/configs/fuloong2e_defconfig new file +1977 -0
1,088 lines not on this page · raw message
arch/mips/configs/fuloong2f_defconfig new file +2630 -0
2,630 lines not on this page · raw message
arch/mips/configs/yeeloong2f_defconfig new file +2641 -0
2,641 lines not on this page · raw message
The rest of this diff is not shown. View the raw message.
Signature · 1 line
1.6.2.1
Part of the diff is not shown here. View the raw message.
PATCH 27/27 add gcc 4.4 support for MIPS and loongson
In reply to [email protected]From: Wu Zhangjin <[email protected]>
the gcc 4.4 support for MIPS mostly refer to this PATCH:
http://www.nabble.com/-PATCH--MIPS:-Handle-removal-of-%27h%27-constraint-in-GCC-4.4-td22192768.html
but have been tuned a little.
because only gcc 4.4 have loongson-specific support, so, we need to choose the suitable -march argument for gcc <= 4.3 and gcc >= 4.4, and we also need to consider use -march=loongson2e and -march=loongson2f for loongson2e and loongson2f respectively. this is handled by adding two new kernel options: CPU_LOONGSON2E and CPU_LOONGSON2F(thanks for the solutin provided by ZhangLe).
I have tested it on FuLoong(2f) in 32bit and 64bit with gcc-4.4 and gcc-4.3. so, basically, it works.
--- arch/mips/Makefile | 9 +++++- arch/mips/include/asm/compiler.h | 10 ++++++ arch/mips/include/asm/delay.h | 58 +++++++++++++++++++++++++------------ arch/mips/include/asm/div64.h | 24 +++++++++++++-- 4 files changed, 77 insertions(+), 24 deletions(-)
arch/mips/Makefile +8 -1
@@ -119,7 +119,14 @@ cflags-$(CONFIG_CPU_R4300) += -march=r4300 -Wa,--trap cflags-$(CONFIG_CPU_VR41XX) += -march=r4100 -Wa,--trap cflags-$(CONFIG_CPU_R4X00) += -march=r4600 -Wa,--trap cflags-$(CONFIG_CPU_TX49XX) += -march=r4600 -Wa,--trap -cflags-$(CONFIG_CPU_LOONGSON2) += -march=r4600 -Wa,--trap + +# only gcc >= 4.4 have the loongson-specific support +cflags-$(CONFIG_CPU_LOONGSON2) += -Wa,--trap +cflags-$(CONFIG_CPU_LOONGSON2E) += $(shell if [ $(call cc-version) -lt 0440 ] ; then \ + echo $(call cc-option,-march=r4600); else echo $(call cc-option,-march=loongson2e); fi ;) +cflags-$(CONFIG_CPU_LOONGSON2F) += $(shell if [ $(call cc-version) -lt 0440 ] ; then \ + echo $(call cc-option,-march=r4600); else echo $(call cc-option,-march=loongson2f); fi ;) + cflags-$(CONFIG_CPU_MIPS32_R1) += $(call cc-option,-march=mips32,-mips32 -U_MIPS_ISA -D_MIPS_ISA=_MIPS_ISA_MIPS32) \ -Wa,-mips32 -Wa,--trap cflags-$(CONFIG_CPU_MIPS32_R2) += $(call cc-option,-march=mips32r2,-mips32r2 -U_MIPS_ISA -D_MIPS_ISA=_MIPS_ISA_MIPS32) \
arch/mips/include/asm/compiler.h +10 -0
@@ -1,5 +1,6 @@/* * Copyright (C) 2004, 2007 Maciej W. Rozycki +* Copyright (C) 2009 Wu Zhangjin, [email protected] * * This file is subject to the terms and conditions of the GNU General Public * License. See the file "COPYING" in the main directory of this archive
@@ -16,4 +17,13 @@#define GCC_REG_ACCUM "accum"#endif +#if __GNUC__ >4 || (__GNUC__ ==4 && __GNUC_MINOR__ >=4 ) +#define GCC_NO_H_CONSTRAINT +#ifdef CONFIG_64BIT +typedef unsigned int uintx_t __attribute__((mode (TI ))); +#else +typedef u64 uintx_t ; +#endif +#endif +#endif /* _ASM_COMPILER_H */
arch/mips/include/asm/delay.h +39 -19
82 lines not on this page · raw message
arch/mips/include/asm/div64.h +20 -4
@@ -1,6 +1,7 @@/* * Copyright (C) 2000, 2004 Maciej W. Rozycki * Copyright (C) 2003, 07 Ralf Baechle ([email protected]) +* Copyright (C) 2009 Wu Zhangjin ([email protected]) * * This file is subject to the terms and conditions of the GNU General Public * License. See the file "COPYING" in the main directory of this archive
@@ -56,6 +57,24 @@ (res) = __quot32; \ __mod32; }) +/* +* __do_divu -- unsigned interger dividing +* +* handle removal of 'h' constraint in GCC 4.4 +*/ +#ifndef GCC_NO_H_CONSTRAINT /* gcc <= 4.3*/ +#define __do_divu () ({ \ + __asm__("divu $0, %z2, %z3" \ + : "=h" (__upper), "=l" (__high) \ + : "Jr" (__high), "Jr" (__base) \ + : GCC_REG_ACCUM); }) + +#else /* gcc >= 4.4 */ +#define __do_divu () ({ \ + __upper = (uintx_t)__high % __base; \ + __high = (uintx_t)__high / __base; }) +#endif +#define do_div (n, base) ({ \ unsigned long long __quot; \ unsigned long __mod; \
@@ -70,10 +89,7 @@ __upper = __high; \ \if (__high) \ - __asm__("divu $0, %z2, %z3" \ - :"=h" (__upper),"=l" (__high) \ - :"Jr" (__high),"Jr" (__base) \ - : GCC_REG_ACCUM); \ +__do_divu ();\ \ __mod =do_div64_32 (__low, __upper, __low, __base); \ \
Signature · 1 line
1.6.2.1
Re: [loongson-PATCH-v1 23/27] Alsa memory maps fixup on mips systems
In reply to [email protected][email protected] wrote:
[...]
sound/core/pcm_native.c static int snd_pcm_mmap_data_fault(struct vm_area_struct *area, · line 3106
Quoted 9 lines
sound/core/pcm_native.c +4
-0@@ -3099,7 +3099,11 @@ static int snd_pcm_mmap_data_fault(struct vm_area_struct *area,return VM_FAULT_SIGBUS ; }else { vaddr = runtime->dma_area + offset; +#if defined(__mips__) && defined(CONFIG_DMA_NONCOHERENT ) + page =virt_to_page (CAC_ADDR (vaddr)); +#else page =virt_to_page (vaddr); +#endif
That is a bit ugly. It would be better to either wrap the fix up in mips specific code so there don't have to be #ifdef __mips__ through out the generic driver code, or fix the driver in some other way if it is making x86 specific assumptions that don't hold in the general case.
The same applies for the remaining #ifdef __mips__ in the patch.
Quoted 56 lines
sound/core/pcm_native.c +5
-0}get_page (page); vmf->page = page;@@ -3214,6 +3218,11 @@ static int snd_pcm_mmap(struct file *file, struct vm_area_struct *area)if (PCM_RUNTIME_CHECK (substream))return -ENXIO ; +#if defined(__mips__) && defined(CONFIG_DMA_NONCOHERENT ) +/* all mmap using uncached mode */ + area->vm_page_prot =pgprot_noncached (area->vm_page_prot); + area->vm_flags |= (VM_RESERVED |VM_IO ); +#endif offset = area->vm_pgoff <<PAGE_SHIFT ;switch (offset) {case SNDRV_PCM_MMAP_OFFSET_STATUS :sound/core/sgbuf.c +9
-0@@ -114,7 +114,11 @@ void *snd_malloc_sgbuf_pages(struct device *device,if (!i) table->addr |= chunk;/* mark head */ table++; +#if defined(__mips__) && defined(CONFIG_DMA_NONCOHERENT ) + *pgtable++ =virt_to_page (CAC_ADDR (tmpb.area)); +#else *pgtable++ =virt_to_page (tmpb.area); +#endif tmpb.area +=PAGE_SIZE ; tmpb.addr +=PAGE_SIZE ; }@@ -125,7 +129,12 @@ void *snd_malloc_sgbuf_pages(struct device *device, } sgbuf->size = size; +#if defined(__mips__) && defined(CONFIG_DMA_NONCOHERENT ) + dmab->area =vmap (sgbuf->page_table, sgbuf->pages, \ +VM_MAP |VM_IO ,pgprot_noncached (PAGE_KERNEL )); +#else dmab->area =vmap (sgbuf->page_table, sgbuf->pages,VM_MAP ,PAGE_KERNEL ); +#endif if (! dmab->area) goto _failed;if (res_size)sound/pci/Kconfig +0
-1@@ -259,7 +259,6 @@ config SND_CS5530 config SND_CS5535AUDIO tristate "CS5535/CS5536 Audio" - depends on X86 && !X86_64 select SND_PCM select SND_AC97_CODEC help
Re: [loongson-PATCH-v1 01/27] fix-warning: incompatible argument type of pci_fixup_irqs
In reply to David DaneyQuoted 23 lines · David Daney
Quoted 22 lines · [email protected] wrote:
From: Wu Zhangjin <[email protected]>
arch/mips/pci/pci.c:160: warning: passing argument 2 of ‘pci_fixup_irqs’ from incompatible pointer type
include/linux/pci.h:void pci_fixup_irqs(u8 (*)(struct pci_dev *, u8 *), int (*)(struct pci_dev *, u8, u8));
arch/mips/pci/pci.c:160:pci_fixup_irqs(pci_common_swizzle, pcibios_map_irq);
arch/mips/include/asm/pci.h:extern int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin);
arch/mips/pci/fixup-malta.cint
__initpcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
Quoted 9 lines
Quoted 1 line
Signed-off-by Wu Zhangjin <[email protected]>This is the correct fix, however there are now Cavium Octeon PCI drivers on Ralf's queue.
If you rebase against the queue (or even if you don't), you can add:
Reviewed-by David Daney <[email protected]>
Merged the lastest ralf's git tree, Rebased, updated and added the Reviewed-by flag.
BTW: i have resent this patch with some update, is there a method to attach the new E-mail to this one?
thanks!
Wu Zhangjin
Quoted 354 lines
Quoted 353 lines
--- arch/mips/include/asm/pci.h | 2 +- arch/mips/pci/fixup-au1000.c | 2 +- arch/mips/pci/fixup-capcella.c | 2 +- arch/mips/pci/fixup-cobalt.c | 2 +- arch/mips/pci/fixup-emma2rh.c | 2 +- arch/mips/pci/fixup-excite.c | 2 +- arch/mips/pci/fixup-ip32.c | 2 +- arch/mips/pci/fixup-lm2e.c | 2 +- arch/mips/pci/fixup-malta.c | 2 +- arch/mips/pci/fixup-mpc30x.c | 2 +- arch/mips/pci/fixup-pmcmsp.c | 2 +- arch/mips/pci/fixup-pnx8550.c | 2 +- arch/mips/pci/fixup-rc32434.c | 2 +- arch/mips/pci/fixup-sni.c | 2 +- arch/mips/pci/fixup-tb0219.c | 2 +- arch/mips/pci/fixup-tb0226.c | 2 +- arch/mips/pci/fixup-tb0287.c | 2 +- arch/mips/pci/fixup-wrppmc.c | 2 +- arch/mips/pci/fixup-yosemite.c | 2 +- arch/mips/pci/pci-bcm1480.c | 2 +- arch/mips/pci/pci-bcm47xx.c | 2 +- arch/mips/pci/pci-ip27.c | 2 +- arch/mips/pci/pci-lasat.c | 2 +- arch/mips/pci/pci-sb1250.c | 2 +- arch/mips/txx9/generic/pci.c | 2 +- 25 files changed, 25 insertions(+), 25 deletions(-)arch/mips/include/asm/pci.h +1
-1@@ -56,7 +56,7 @@ extern void register_pci_controller(struct pci_controller *hose);/* * board supplied pci irq fixup routine */ -extern int pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin); +extern int pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin);/* Can be used to override the logic in pci_scan_bus for skipping arch/mips/pci/fixup-au1000.c +1
-1@@ -31,7 +31,7 @@extern char irq_tab_alchemy[][5 ]; -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return irq_tab_alchemy[slot][pin]; }arch/mips/pci/fixup-capcella.c +1
-1@@ -38,7 +38,7 @@ static char irq_tab_capcella[][5] __initdata = { [14] = { -1, INTA, INTB, INTC, INTD } }; -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return irq_tab_capcella[slot][pin]; }arch/mips/pci/fixup-cobalt.c +1
-1@@ -175,7 +175,7 @@ static char irq_tab_raq2[] __initdata = { [COBALT_PCICONF_ETH1] = ETH1_IRQ }; -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {if (cobalt_board_id <=COBALT_BRD_ID_QUBE1 )return irq_tab_qube1[slot];arch/mips/pci/fixup-emma2rh.c +1
-1@@ -88,7 +88,7 @@ static void __devinit emma2rh_pci_host_fixup(struct pci_dev *dev)DECLARE_PCI_FIXUP_HEADER (PCI_VENDOR_ID_NEC ,PCI_DEVICE_ID_NEC_EMMA2RH , emma2rh_pci_host_fixup); -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return irq_map[slot][pin]; }arch/mips/pci/fixup-excite.c +1
-1@@ -21,7 +21,7 @@#include <linux/pci.h> #include <excite.h> -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {if (pin ==0 )return -1 ;arch/mips/pci/fixup-ip32.c +1
-1@@ -39,7 +39,7 @@ static char irq_tab_mace[][5] __initdata = {* irqs. I suppose a device without a pin A will thank us for doing it * right if there exists such a broken piece of crap. */ -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return irq_tab_mace[slot][pin]; }arch/mips/pci/fixup-lm2e.c +1
-1@@ -36,7 +36,7 @@/* South bridge slot number is set by the pci probe process */ static u8 sb_slot =5 ; -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {int irq =0 ;arch/mips/pci/fixup-malta.c +1
-1@@ -36,7 +36,7 @@ static char irq_tab[][5] __initdata = { {0, PCID, PCIA, PCIB, PCIC } /* 21: PCI Slot 4 */ }; -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {int virq; virq = irq_tab[slot][pin];arch/mips/pci/fixup-mpc30x.c +1
-1@@ -34,7 +34,7 @@ static const int irq_tab_mpc30x[] __initdata = { [29] = MQ200_IRQ, }; -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {if (slot ==30 )return internal_func_irqs[PCI_FUNC (dev->devfn)];arch/mips/pci/fixup-pmcmsp.c +1
-1@@ -202,7 +202,7 @@ int pcibios_plat_dev_init(struct pci_dev *dev)* RETURNS: IRQ number * ****************************************************************************/ -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {#if !defined(CONFIG_PMC_MSP7120_GW ) && !defined(CONFIG_PMC_MSP7120_EVAL )printk (KERN_WARNING "PCI: unknown board, no PCI IRQs assigned.\n" );arch/mips/pci/fixup-pnx8550.c +1
-1@@ -45,7 +45,7 @@ void __init pcibios_fixup(void)/* nothing to do here */ } -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return pnx8550_irq_tab[slot][pin]; }arch/mips/pci/fixup-rc32434.c +1
-1@@ -37,7 +37,7 @@ static int __devinitdata irq_map[2][12] = { {0, 0, 1, 3, 0, 2, 1, 3, 0, 2, 1, 3} }; -int __devinit pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __devinit pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {int irq =0 ;arch/mips/pci/fixup-sni.c +1
-1@@ -130,7 +130,7 @@ static inline int is_rm300_revd(void)return (csmsr &0xa0 ) ==0x20 ; } -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {switch (sni_brd_type) {case SNI_BRD_PCI_TOWER_CPLUS :arch/mips/pci/fixup-tb0219.c +1
-1@@ -23,7 +23,7 @@#include <asm/vr41xx/tb0219.h> -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {int irq =-1 ;arch/mips/pci/fixup-tb0226.c +1
-1@@ -23,7 +23,7 @@#include <asm/vr41xx/giu.h> #include <asm/vr41xx/tb0226.h> -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {int irq =-1 ;arch/mips/pci/fixup-tb0287.c +1
-1@@ -22,7 +22,7 @@#include <asm/vr41xx/tb0287.h> -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {unsigned char bus;int irq =-1 ;arch/mips/pci/fixup-wrppmc.c +1
-1@@ -25,7 +25,7 @@ static char pci_irq_tab[PCI_SLOT_MAXNR][5] __initdata = { [6] = {0, WRPPMC_PCI_INTA_IRQ, 0, 0, 0}, }; -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return pci_irq_tab[slot][pin]; }arch/mips/pci/fixup-yosemite.c +1
-1@@ -26,7 +26,7 @@#include <linux/init.h> #include <linux/pci.h> -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {if (pin ==0 )return -1 ;arch/mips/pci/pci-bcm1480.c +1
-1@@ -74,7 +74,7 @@ static inline void WRITECFG32(u32 addr, u32 data) *(u32 *)(cfg_space + (addr & ~3 )) = data; } -int pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {if (pin ==0 )return -1 ;arch/mips/pci/pci-bcm47xx.c +1
-1@@ -26,7 +26,7 @@#include <linux/pci.h> #include <linux/ssb/ssb.h> -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return 0 ; }arch/mips/pci/pci-ip27.c +1
-1@@ -141,7 +141,7 @@ int __cpuinit bridge_probe(nasid_t nasid, int widget_id, int masterwid)* A given PCI device, in general, should be able to intr any of the cpus * on any one of the hubs connected to its xbow. */ -int __devinit pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __devinit pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return 0 ; }arch/mips/pci/pci-lasat.c +1
-1@@ -61,7 +61,7 @@ arch_initcall(lasat_pci_setup);#define LASAT_IRQ_PCIC (LASAT_IRQ_BASE + 7)#define LASAT_IRQ_PCID (LASAT_IRQ_BASE + 8) -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {switch (slot) {case 1 :arch/mips/pci/pci-sb1250.c +1
-1@@ -84,7 +84,7 @@ static inline void WRITECFG32(u32 addr, u32 data) *(u32 *) (cfg_space + (addr & ~3 )) = data; } -int pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return dev->irq; }arch/mips/txx9/generic/pci.c +1
-1@@ -382,7 +382,7 @@ int pcibios_plat_dev_init(struct pci_dev *dev)return 0 ; } -int __init pcibios_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) +int __init pcibios_map_irq (struct pci_dev *dev,u8 slot,u8 pin) {return txx9_board_vec->pci_map_irq (dev, slot, pin); }
Re: [loongson-PATCH-v1 23/27] Alsa memory maps fixup on mips systems
In reply to David DaneyQuoted 17 lines · David Daney
[email protected] wrote:
[...]sound/core/pcm_native.c static int snd_pcm_mmap_data_fault(struct vm_area_struct *area, · line 3106
Quoted 9 lines
sound/core/pcm_native.c +4
-0@@ -3099,7 +3099,11 @@ static int snd_pcm_mmap_data_fault(struct vm_area_struct *area,return VM_FAULT_SIGBUS ; }else { vaddr = runtime->dma_area + offset; +#if defined(__mips__) && defined(CONFIG_DMA_NONCOHERENT ) + page =virt_to_page (CAC_ADDR (vaddr)); +#else page =virt_to_page (vaddr); +#endif That is a bit ugly. It would be better to either wrap the fix up in mips specific code so there don't have to be #ifdef
__mips__through out the generic driver code, or fix the driver in some other way if it is making x86 specific assumptions that don't hold in the general case.
Quoted 3 lines
The same applies for the remaining #ifdef
__mips__in the patch.
nod, will be tuned later.
thanks,
Wu Zhangjin
Quoted 59 lines
Quoted 58 lines
sound/core/pcm_native.c +5
-0}get_page (page); vmf->page = page;@@ -3214,6 +3218,11 @@ static int snd_pcm_mmap(struct file *file, struct vm_area_struct *area)if (PCM_RUNTIME_CHECK (substream))return -ENXIO ; +#if defined(__mips__) && defined(CONFIG_DMA_NONCOHERENT ) +/* all mmap using uncached mode */ + area->vm_page_prot =pgprot_noncached (area->vm_page_prot); + area->vm_flags |= (VM_RESERVED |VM_IO ); +#endif offset = area->vm_pgoff <<PAGE_SHIFT ;switch (offset) {case SNDRV_PCM_MMAP_OFFSET_STATUS :sound/core/sgbuf.c +9
-0@@ -114,7 +114,11 @@ void *snd_malloc_sgbuf_pages(struct device *device,if (!i) table->addr |= chunk;/* mark head */ table++; +#if defined(__mips__) && defined(CONFIG_DMA_NONCOHERENT ) + *pgtable++ =virt_to_page (CAC_ADDR (tmpb.area)); +#else *pgtable++ =virt_to_page (tmpb.area); +#endif tmpb.area +=PAGE_SIZE ; tmpb.addr +=PAGE_SIZE ; }@@ -125,7 +129,12 @@ void *snd_malloc_sgbuf_pages(struct device *device, } sgbuf->size = size; +#if defined(__mips__) && defined(CONFIG_DMA_NONCOHERENT ) + dmab->area =vmap (sgbuf->page_table, sgbuf->pages, \ +VM_MAP |VM_IO ,pgprot_noncached (PAGE_KERNEL )); +#else dmab->area =vmap (sgbuf->page_table, sgbuf->pages,VM_MAP ,PAGE_KERNEL ); +#endif if (! dmab->area) goto _failed;if (res_size)sound/pci/Kconfig +0
-1@@ -259,7 +259,6 @@ config SND_CS5530 config SND_CS5535AUDIO tristate "CS5535/CS5536 Audio" - depends on X86 && !X86_64 select SND_PCM select SND_AC97_CODEC help
Re: [loongson-PATCH-v1 03/27] fix-error: incompatiable argument type of clear_user
In reply to [email protected]Quoted 7 lines · On Thu, May 21, 2009 at 05:50:01AM +0800, [email protected] wrote:
From: Wu Zhangjin <[email protected]>
there are lots of warnings about the macro:
clear_userin linux-mips.the type of the second argument of
access_okshould be (void__user*), but there is an un-needed (unsigned long) conversion before__cl_addr, so, remove the (unsigned long) will fix this problem.
I assume you're talking about sparse warnings, not gcc warnings?
Either way, access_ok() is defined to take pointer arguments, so patch applied. Thanks!
Ralf
Re: [loongson-PATCH-v1 02/27] fix-warning: incompatible argument type of virt_to_phys
In reply to [email protected]Quoted 9 lines · On Thu, May 21, 2009 at 05:49:30AM +0800, [email protected] wrote:
mm/page_alloc.c:1760: warning: passing argument 1 of ‘virt_to_phys’ makes pointer from integer without a cast
mm/page_alloc.c:1760... unsigned long addr; ... split_page(virt_to_page(addr), order);
Quoted 7 lines
arch/mips/include/asm/page.h#define virt_to_page(kaddr) pfn_to_page(PFN_DOWN(virt_to_phys(kaddr))) #define virt_addr_valid(kaddr) pfn_valid(PFN_DOWN(virt_to_phys(kaddr)))
arch/mips/include/asm/io.h
static inline unsigned longvirt_to_phys(volatile const void *address)
I'm inclined to say the caller needs fixing. Most callers are passing some kind of pointer argument but here an unsigned long is being passed in. I'm checking with the mm maintainers. For now I'll apply this patch to my -mm queue.
Ralf
Re: [loongson-PATCH-v1 01/27] fix-warning: incompatible argument type of pci_fixup_irqs
In reply to David DaneyQuoted 2 lines · David Daney
This is the correct fix, however there are now Cavium Octeon PCI drivers on Ralf's queue.
The reason for the const is that people keep doing very broken things in pcibios_map_irq(). I don't see any legitimate reason why pcibios_map_irq should modifiy the structure the first argument is pointing to, so I changed it to const just to be a pain in the arse. Of course the warning should be rectified but this requires talking to the upstream PCI guys.
Ralf
Re: [loongson-PATCH-v1 22/27] Hibernation Support in mips system
In reply to [email protected]On Thu, May 21, 2009 at 06:11:11AM +0800, [email protected] wrote:
This patch does no longer apply. When submitting new code please always base it on the latest development kernel. Any -stable kernel will probably be too old.
Can you rebase this patch to the master branch of linux-mips.org and re-submit? Thanks!
Ralf
Re: [loongson-PATCH-v1 22/27] Hibernation Support in mips system
In reply to [email protected]Quoted 25 lines · On Thu, 21 May 2009 06:11:11 +0800, [email protected] wrote:
arch/mips/power/cpu.c new file +22
-0@@ -0,0 +1,51 @@ +/* +* Suspend support specific for mips. +* +*/ +#include <linux/mm.h> +#include <asm/mipsregs.h> +#include <asm/page.h> +#include <linux/suspend.h> + +/* References to section boundaries */ +extern const void __nosave_begin, __nosave_end; + +static uint32_t saved_status; +unsigned long + saved_ra, + saved_sp, + saved_fp, + saved_gp, + saved_s0, + saved_s1, + saved_s2, + saved_s3,
arch/mips/power/cpu.c line 32
Quoted 10 lines
arch/mips/power/cpu.c new file +10
-0+ saved_s4, + saved_s5, + saved_s6, + saved_s7, + saved_a0, + saved_a1, + saved_a2, + saved_a3, + saved_v0, + saved_v1;
Instead of enumerating them, I would prefer something like "struct pt_regs saved_regs" or "unsigned long saved_regs[32]".
arch/mips/power/cpu.c line 37
Quoted 4 lines
arch/mips/power/cpu.c new file +4
-0+void save_processor_state (void ) +{ + saved_status =read_c0_status (); +}
No need to save/restore floating point registers?
arch/mips/power/cpu.c line 48
Quoted 5 lines
arch/mips/power/cpu.c new file +5
-0+int pfn_is_nosave (unsigned long pfn) +{ +unsigned long nosave_begin_pfn =__pa (&__nosave_begin) >>PAGE_SHIFT ; +unsigned long nosave_end_pfn = \ +PAGE_ALIGN (__pa (&__nosave_end)) >>PAGE_SHIFT ;
Unneeded backslash concatenation.PFN_UP(), PFN_DOWN() can be used.
arch/mips/power/cpu.c line 46
Quoted 5 lines
arch/mips/power/cpu.c new file +5
-0+LEAF (swsusp_arch_suspend) + PTR_LA t0, saved_ra + PTR_S ra, (t0) + PTR_LA t0, saved_sp + PTR_S sp, (t0)
The MIPS assembly language accepts symbol for PTR_S, i.e.:
PTR_S ra, saved_ra
Or, if you converted saved_xxx into struct or array, you can do something like this:
PTR_LA t0, saved_regs PTR_S ra, PT_R31(t0) PTR_S sp, PT_R29(t0) ...
arch/mips/power/cpu.c line 48
Quoted 2 lines
arch/mips/power/cpu.c new file +2
-0+j swsusp_save + nop
This nop is required?
---
Atsushi Nemoto
Re: [loongson-PATCH-v1 24/27] fixup for FUJITSU disk
In reply to [email protected]Quoted 4 lines · On Thursday 21 May 2009 00:12:46 [email protected] wrote:
From: Wu Zhangjin <[email protected]>
This is originally from the to-mips branch from
http://dev.lemote.com/code/linux_loongson
Sadly, the patch description lacks all the important information.
What is the original problem that this fixup tries to address?
Is it limited to amd74xx controllers?
[ We are generalizing quirk_drives handling currently... ]
Quoted 48 lines
Signed-off-by Wu Zhangjin <[email protected]>--- drivers/ide/amd74xx.c | 19 +++++++++++++++++++ 1 files changed, 19 insertions(+), 0 deletions(-)drivers/ide/amd74xx.c +19
-0@@ -23,6 +23,11 @@#define DRV_NAME "amd74xx" +static const char *am74xx_quirk_drives[] = { +"FUJITSU MHZ2160BH G2" , +NULL +}; +enum {AMD_IDE_CONFIG =0x41 ,AMD_CABLE_DETECT =0x42 ,@@ -112,6 +117,19 @@ static void amd_set_pio_mode(ide_drive_t *drive, const u8 pio)amd_set_drive (drive,XFER_PIO_0 + pio); } +static void amd_quirkproc (ide_drive_t *drive) +{ +const char **list, *m = (char *)&drive->id[ATA_ID_PROD ]; + +for (list = am74xx_quirk_drives; *list !=NULL ; list++) +if (strstr (m, *list) !=NULL ) { + drive->quirk_list =2 ; +return ; + } + + drive->quirk_list =0 ; +} +static void amd7409_cable_detect (struct pci_dev *dev) {/* no host side cable detection */ @@ -194,6 +212,7 @@ static void __devinit init_hwif_amd74xx(ide_hwif_t *hwif)static const struct ide_port_ops amd_port_ops = { .set_pio_mode = amd_set_pio_mode, .set_dma_mode = amd_set_drive, + .quirkproc = amd_quirkproc, .cable_detect = amd_cable_detect, };
Re: [loongson-PATCH-v1 24/27] fixup for FUJITSU disk
Quoted 11 lines · 在 2009-05-22五的 20:32 +0200,Bartlomiej Zolnierkiewicz写道:
Quoted 4 lines · On Thursday 21 May 2009 00:12:46 [email protected] wrote:
From: Wu Zhangjin <[email protected]>
This is originally from the to-mips branch from
http://dev.lemote.com/code/linux_loongsonSadly, the patch description lacks all the important information.
What is the original problem that this fixup tries to address?
Is it limited to amd74xx controllers?
In loongson2f yeeloong machines, the ide controller is AMD cs5536, or say amd74xx, and the hard drives is Fujistu.
While debuging the hard disk suspned and resume, the ide irq can not be cleared. I guess this is a fake interrupt, hence the clear irq action can not be finished.
This patch is to fix this issue. Maybe other controller and drives also have this issue, but I am not sure.
Thanks for your reply.
Quoted 52 lines
[ We are generalizing
quirk_driveshandling currently... ]Quoted 48 lines
Signed-off-by Wu Zhangjin <[email protected]>--- drivers/ide/amd74xx.c | 19 +++++++++++++++++++ 1 files changed, 19 insertions(+), 0 deletions(-)drivers/ide/amd74xx.c +19
-0@@ -23,6 +23,11 @@#define DRV_NAME "amd74xx" +static const char *am74xx_quirk_drives[] = { +"FUJITSU MHZ2160BH G2" , +NULL +}; +enum {AMD_IDE_CONFIG =0x41 ,AMD_CABLE_DETECT =0x42 ,@@ -112,6 +117,19 @@ static void amd_set_pio_mode(ide_drive_t *drive, const u8 pio)amd_set_drive (drive,XFER_PIO_0 + pio); } +static void amd_quirkproc (ide_drive_t *drive) +{ +const char **list, *m = (char *)&drive->id[ATA_ID_PROD ]; + +for (list = am74xx_quirk_drives; *list !=NULL ; list++) +if (strstr (m, *list) !=NULL ) { + drive->quirk_list =2 ; +return ; + } + + drive->quirk_list =0 ; +} +static void amd7409_cable_detect (struct pci_dev *dev) {/* no host side cable detection */ @@ -194,6 +212,7 @@ static void __devinit init_hwif_amd74xx(ide_hwif_t *hwif)static const struct ide_port_ops amd_port_ops = { .set_pio_mode = amd_set_pio_mode, .set_dma_mode = amd_set_drive, + .quirkproc = amd_quirkproc, .cable_detect = amd_cable_detect, };
Re: [loongson-PATCH-v1 22/27] Hibernation Support in mips system
In reply to Atsushi NemotoQuoted 31 lines · 在 2009-05-22五的 22:01 +0900,Atsushi Nemoto写道:
Quoted 30 lines · On Thu, 21 May 2009 06:11:11 +0800, [email protected] wrote:
arch/mips/power/cpu.c new file +27
-0@@ -0,0 +1,51 @@ +/* +* Suspend support specific for mips. +* +*/ +#include <linux/mm.h> +#include <asm/mipsregs.h> +#include <asm/page.h> +#include <linux/suspend.h> + +/* References to section boundaries */ +extern const void __nosave_begin, __nosave_end; + +static uint32_t saved_status; +unsigned long + saved_ra, + saved_sp, + saved_fp, + saved_gp, + saved_s0, + saved_s1, + saved_s2, + saved_s3, + saved_s4, + saved_s5, + saved_s6, + saved_s7, + saved_a0,
Quoted 8 lines
arch/mips/power/cpu.c line 32
Quoted 5 lines
arch/mips/power/cpu.c new file +5
-0+ saved_a1, + saved_a2, + saved_a3, + saved_v0, + saved_v1;Instead of enumerating them, I would prefer something like "struct
pt_regssaved_regs" or "unsigned long saved_regs[32]".
This implementation is referencing the x86 platform. Not all the 32 reigsters are needed to save.
Maybe the whole registers needed to save can still be reduced.
Quoted 7 lines
arch/mips/power/cpu.c line 37
Quoted 5 lines
arch/mips/power/cpu.c new file +4
-0+void save_processor_state (void ) +{ + saved_status =read_c0_status (); +}No need to save/restore floating point registers?
the floating point registers are not used by kernel, for user part, they are already saved while entering into kernel mode.
Quoted 37 lines
arch/mips/power/cpu.c line 48
Quoted 6 lines
arch/mips/power/cpu.c new file +5
-0+int pfn_is_nosave (unsigned long pfn) +{ +unsigned long nosave_begin_pfn =__pa (&__nosave_begin) >>PAGE_SHIFT ; +unsigned long nosave_end_pfn = \ +PAGE_ALIGN (__pa (&__nosave_end)) >>PAGE_SHIFT ;Unneeded backslash concatenation.
PFN_UP(),PFN_DOWN()can be used.arch/mips/power/cpu.c line 46
Quoted 5 lines
arch/mips/power/cpu.c new file +5
-0+LEAF (swsusp_arch_suspend) + PTR_LA t0, saved_ra + PTR_S ra, (t0) + PTR_LA t0, saved_sp + PTR_S sp, (t0)The MIPS assembly language accepts symbol for
PTR_S, i.e.:
PTR_Sra,saved_raOr, if you converted
saved_xxxinto struct or array, you can do something like this:PTR_LA t0, saved_regs PTR_S ra, PT_R31(t0) PTR_S sp, PT_R29(t0) ...arch/mips/power/cpu.c line 48
Quoted 2 lines
arch/mips/power/cpu.c new file +2
-0+j swsusp_save + nopThis nop is required?
---
Atsushi Nemoto
Re: [loongson-PATCH-v1 24/27] fixup for FUJITSU disk
In reply to yanhQuoted 7 lines · On Saturday 23 May 2009 09:11:42 yanh wrote:
Quoted 6 lines · 在 2009-05-22五的 20:32 +0200,Bartlomiej Zolnierkiewicz写道:
Quoted 4 lines · On Thursday 21 May 2009 00:12:46 [email protected] wrote:
From: Wu Zhangjin <[email protected]>
This is originally from the to-mips branch from
http://dev.lemote.com/code/linux_loongson
Quoted 8 lines
Quoted 5 lines
Sadly, the patch description lacks all the important information.
What is the original problem that this fixup tries to address?
Is it limited to amd74xx controllers?
In loongson2f yeeloong machines, the ide controller is AMD cs5536, or say amd74xx, and the hard drives is Fujistu.
Then it should use the new & shiny :) native cs5536 IDE host driver instead of legacy support in amd74xx...
Quoted 3 lines
While debuging the hard disk suspned and resume, the ide irq can not be cleared. I guess this is a fake interrupt, hence the clear irq action can not be finished.
AFAICS the only change that the fixup would cause for suspend/resume paths is the one in ide_config_drive_speed() which is called during resume to set transfer mode on the drive:
tp_ops->write_devctl(hwif, ATA_NIEN | ATA_DEVCTL_OBS);
memset(&tf, 0, sizeof(tf));
tf.feature = SETFEATURES_XFER;
tf.nsect = speed;
tp_ops->tf_load(drive, &tf, IDE_VALID_FEATURE | IDE_VALID_NSECT);
tp_ops->exec_command(hwif, ATA_CMD_SET_FEATURES);
--->
if (drive->quirk_list == 2)
tp_ops->write_devctl(hwif, ATA_DEVCTL_OBS);
--->
error = __ide_wait_stat(drive, drive->ready_stat,
ATA_BUSY | ATA_DRQ | ATA_ERR,
WAIT_CMD, &stat);Please tell me I if understand the issue correctly: if the above quirk is not executed we end up with spurious IRQs, right?
Quoted 2 lines
This patch is to fix this issue. Maybe other controller and drives also have this issue, but I am not sure.
Probably moving it to a generic quirk_drives list later will be useful...
Anyway this fixup needs to be ported to / verified with cs5536 first.
Thanks.
Bart
Re: [loongson-PATCH-v1 22/27] Hibernation Support in mips system
In reply to yanhQuoted 3 lines · yanh
Quoted 3 lines
Quoted 3 lines
arch/mips/power/cpu.c new file +3
-0+unsigned long + saved_ra, + saved_sp,
...
Quoted 8 lines
Quoted 5 lines
arch/mips/power/cpu.c line 32
Quoted 2 lines
arch/mips/power/cpu.c new file +2
-0+ saved_v0, + saved_v1;Instead of enumerating them, I would prefer something like "struct
pt_regssaved_regs" or "unsigned long saved_regs[32]".This implementation is referencing the x86 platform. Not all the 32 reigsters are needed to save.
Maybe the whole registers needed to save can still be reduced.
I did not mean save/restore all registers. I just mean using only one symbol (struct or array). Though the struct or array contains some unused members, it saves many instructions in swsusp_arch_{suspend,resume}.
For saving N registers, (N * 2) instructions are required to save to individual variables, but (N + 2) instructions are required to save to array or struct.
Quoted 8 lines
Quoted 6 lines
arch/mips/power/cpu.c line 37
Quoted 4 lines
arch/mips/power/cpu.c new file +4
-0+void save_processor_state (void ) +{ + saved_status =read_c0_status (); +}No need to save/restore floating point registers?
the floating point registers are not used by kernel, for user part, they are already saved while entering into kernel mode.
No, floating point registers are not saved on entering into kernel. They are saved on context switch.
---
Atsushi Nemoto
Re: [loongson-PATCH-v1 22/27] Hibernation Support in mips system
In reply to Ralf BaechleQuoted 9 lines · Ralf Baechle
On Thu, May 21, 2009 at 06:11:11AM +0800, [email protected] wrote:
This patch does no longer apply. When submitting new code please always base it on the latest development kernel. Any -stable kernel will probably be too old.
Can you rebase this patch to the master branch of linux-mips.org and re-submit? Thanks!
seems rebase will generate lots of merge conflicts, i am cloning the master branch of linux-mips.org and build a new branch.
Quoted 1 line
Ralf
Re: [loongson-PATCH-v1 24/27] fixup for FUJITSU disk
In reply to Bartlomiej ZolnierkiewiczQuoted 41 lines · 在 2009-05-23六的 13:47 +0200,Bartlomiej Zolnierkiewicz写道:
Quoted 7 lines · On Saturday 23 May 2009 09:11:42 yanh wrote:
Quoted 6 lines · 在 2009-05-22五的 20:32 +0200,Bartlomiej Zolnierkiewicz写道:
Quoted 4 lines · On Thursday 21 May 2009 00:12:46 [email protected] wrote:
From: Wu Zhangjin <[email protected]>
This is originally from the to-mips branch from
http://dev.lemote.com/code/linux_loongsonQuoted 8 lines
Quoted 5 lines
Sadly, the patch description lacks all the important information.
What is the original problem that this fixup tries to address?
Is it limited to amd74xx controllers?
In loongson2f yeeloong machines, the ide controller is AMD cs5536, or say amd74xx, and the hard drives is Fujistu.
Then it should use the new & shiny :) native cs5536 IDE host driver instead of legacy support in amd74xx...
Quoted 3 lines
While debuging the hard disk suspned and resume, the ide irq can not be cleared. I guess this is a fake interrupt, hence the clear irq action can not be finished.
AFAICS the only change that the fixup would cause for suspend/resume paths is the one in
ide_config_drive_speed()which is called during resume to set transfer mode on the drive:tp_ops->write_devctl(hwif, ATA_NIEN | ATA_DEVCTL_OBS); memset(&tf, 0, sizeof(tf)); tf.feature = SETFEATURES_XFER; tf.nsect = speed; tp_ops->tf_load(drive, &tf, IDE_VALID_FEATURE | IDE_VALID_NSECT); tp_ops->exec_command(hwif, ATA_CMD_SET_FEATURES); ---> if (drive->quirk_list == 2) tp_ops->write_devctl(hwif, ATA_DEVCTL_OBS);
Quoted 7 lines
--->
error = __ide_wait_stat(drive, drive->ready_stat, ATA_BUSY | ATA_DRQ | ATA_ERR, WAIT_CMD, &stat);Please tell me I if understand the issue correctly: if the above quirk is not executed we end up with spurious IRQs, right?
right.
Quoted 7 lines
Quoted 3 lines
This patch is to fix this issue. Maybe other controller and drives also have this issue, but I am not sure.
Probably moving it to a generic
quirk_driveslist later will be useful...Anyway this fixup needs to be ported to / verified with cs5536 first.
the cs5536 pata driver have some geode platform dependent codes. We can just ignore it, but the performance is poor(using hdparm to test it), which only get 22+ MB/s. we find it only use udma2. However if using amd74xx driver, it can set udma5, and the speed can reach to 50+ MB/s.
we will test whether this driver is working well without this patch.
Anyway, thanks your advice.
Quoted 4 lines
Thanks.
Bart
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: [loongson-PATCH-v1 24/27] fixup for FUJITSU disk
Quoted 66 lines · yanh
Quoted 47 lines · 在 2009-05-23六的 13:47 +0200,Bartlomiej Zolnierkiewicz写道:
Quoted 9 lines · On Saturday 23 May 2009 09:11:42 yanh wrote:
Quoted 7 lines · 在 2009-05-22五的 20:32 +0200,Bartlomiej Zolnierkiewicz写道:
Quoted 5 lines · On Thursday 21 May 2009 00:12:46 [email protected] wrote:
From: Wu Zhangjin <[email protected]>
This is originally from the to-mips branch from
http://dev.lemote.com/code/linux_loongsonQuoted 9 lines
Quoted 6 lines
Sadly, the patch description lacks all the important information.
What is the original problem that this fixup tries to address?
Is it limited to amd74xx controllers?
In loongson2f yeeloong machines, the ide controller is AMD cs5536, or say amd74xx, and the hard drives is Fujistu.
Then it should use the new & shiny :) native cs5536 IDE host driver instead of legacy support in amd74xx...
Quoted 4 lines
While debuging the hard disk suspned and resume, the ide irq can not be cleared. I guess this is a fake interrupt, hence the clear irq action can not be finished.
AFAICS the only change that the fixup would cause for suspend/resume paths is the one in
ide_config_drive_speed()which is called during resume to set transfer mode on the drive:tp_ops->write_devctl(hwif, ATA_NIEN | ATA_DEVCTL_OBS); memset(&tf, 0, sizeof(tf)); tf.feature = SETFEATURES_XFER; tf.nsect = speed; tp_ops->tf_load(drive, &tf, IDE_VALID_FEATURE | IDE_VALID_NSECT); tp_ops->exec_command(hwif, ATA_CMD_SET_FEATURES); ---> if (drive->quirk_list == 2) tp_ops->write_devctl(hwif, ATA_DEVCTL_OBS);Quoted 8 lines
--->
error = __ide_wait_stat(drive, drive->ready_stat, ATA_BUSY | ATA_DRQ | ATA_ERR, WAIT_CMD, &stat);Please tell me I if understand the issue correctly: if the above quirk is not executed we end up with spurious IRQs, right?
right.
Quoted 7 lines
Quoted 3 lines
This patch is to fix this issue. Maybe other controller and drives also have this issue, but I am not sure.
Probably moving it to a generic
quirk_driveslist later will be useful...Anyway this fixup needs to be ported to / verified with cs5536 first.
Quoted 9 lines
the cs5536 pata driver have some geode platform dependent codes. We can just ignore it, but the performance is poor(using hdparm to test it), which only get 22+ MB/s. we find it only use udma2. However if using amd74xx driver, it can set udma5, and the speed can reach to 50+ MB/s.
we will test whether this driver is working well without this patch.
Anyway, thanks your advice.
Use the driver drivers/ata/pata_cs5536.c, unfortunately it also have the same issue.
Quoted 8 lines
Quoted 4 lines
Thanks.
Bart
Signature · 8 lines
--------------------------------------------------------- Hongbing,Hu (Software Department) Tel: 0512-52308631 E-mail: [email protected] MSN: [[email protected]] JiangSu Lemote Corp. Ltd. MengLan, Yushan, Changshu, JiangSu Province, China ---------------------------------------------------------
Re: [loongson-PATCH-v1 24/27] fixup for FUJITSU disk
Quoted 1 line · On Monday 25 May 2009 09:35:48 胡洪兵 wrote:
yanh 写道:
[...]
Quoted 11 lines
Quoted 9 lines
the cs5536 pata driver have some geode platform dependent codes. We can just ignore it, but the performance is poor(using hdparm to test it), which only get 22+ MB/s. we find it only use udma2. However if using amd74xx driver, it can set udma5, and the speed can reach to 50+ MB/s.
we will test whether this driver is working well without this patch.
Anyway, thanks your advice.
Use the driver
drivers/ata/pata_cs5536.c, unfortunately it also have the same issue.
Both drivers (pata_cs5536 & cs5536) should handle UDMA5.
Could you please explain the issue with platform specific code a bit more?
Is it related to a cable detection by any chance?
Thanks.
Bart
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: [loongson-PATCH-v1 24/27] fixup for FUJITSU disk
Quoted 13 lines · Bartlomiej Zolnierkiewicz
Quoted 1 line
yanh 写道:
[...]
Quoted 8 lines
Quoted 8 lines
the cs5536 pata driver have some geode platform dependent codes. We can just ignore it, but the performance is poor(using hdparm to test it), which only get 22+ MB/s. we find it only use udma2. However if using amd74xx driver, it can set udma5, and the speed can reach to 50+ MB/s.
we will test whether this driver is working well without this patch.
Anyway, thanks your advice.
Quoted 7 lines
Quoted 1 line
Use the driver
drivers/ata/pata_cs5536.c, unfortunately it also have the same issue.Both drivers (
pata_cs5536& cs5536) should handle UDMA5.Could you please explain the issue with platform specific code a bit more?
Is it related to a cable detection by any chance?
I guess it's rdmsr()/wrmsr()...
Quoted 2 lines
Thanks.
Bart
MBR, Sergei
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: [loongson-PATCH-v1 24/27] fixup for FUJITSU disk
Quoted 6 lines
Quoted 6 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
"Sergei" == Sergei Shtylyov <[email protected]> writes:
Could you please explain the issue with platform specific code a bit more?
Is it related to a cable detection by any chance?
Sergei> I guess it's rdmsr()/wrmsr()...
Those are only used when the driver is explicitly loaded with use_msr=1. The default is to use PCI config space/VSA.
In any case I have yet to see a CS5536 system whose BIOS sets the cable detection bit. If that's the problem I guess we could add a quirk flag to override the (lack of) BIOS setting.
Signature · 1 line
Martin K. Petersen Oracle Linux Engineering
Re: [loongson-PATCH-v1 24/27] fixup for FUJITSU disk
Hello.
Quoted 9 lines · Martin K. Petersen
Quoted 4 lines
Quoted 4 lines
Could you please explain the issue with platform specific code a bit more?
Is it related to a cable detection by any chance?
Sergei> I guess it's rdmsr()/wrmsr()...
Those are only used when the driver is explicitly loaded with use_msr=1. The default is to use PCI config space/VSA.
But you need them defined for the driver to build...
MBR, Sergei
Re: [loongson-PATCH-v1 24/27] fixup for FUJITSU disk
In reply to Martin K. PetersenQuoted 8 lines · 在 2009-05-25一的 15:10 -0400,Martin K. Petersen写道:
Quoted 6 lines
Quoted 6 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
"Sergei" == Sergei Shtylyov <[email protected]> writes:
Could you please explain the issue with platform specific code a bit more?
Is it related to a cable detection by any chance?
Sergei> I guess it's rdmsr()/wrmsr()...
currently, we just commented out the rdmsr/wrmsr.
and we use pci VSA to access it.
Quoted 8 lines
Those are only used when the driver is explicitly loaded with use_msr=1. The default is to use PCI config space/VSA.
In any case I have yet to see a CS5536 system whose BIOS sets the cable detection bit. If that's the problem I guess we could add a quirk flag to override the (lack of) BIOS setting.
This may be the cause that udma5 cannot be set.
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: [loongson-PATCH-v1 22/27] Hibernation Support in mips system
In reply to Atsushi NemotoQuoted 14 lines · 在 2009-05-23六的 21:30 +0900,Atsushi Nemoto写道:
Quoted 3 lines · yanh
Quoted 3 lines
Quoted 3 lines
arch/mips/power/cpu.c new file +3
-0+unsigned long + saved_ra, + saved_sp,...
Quoted 8 lines
Quoted 5 lines
arch/mips/power/cpu.c line 32
Quoted 2 lines
arch/mips/power/cpu.c new file +2
-0+ saved_v0, + saved_v1;Instead of enumerating them, I would prefer something like "struct
pt_regssaved_regs" or "unsigned long saved_regs[32]".This implementation is referencing the x86 platform. Not all the 32 reigsters are needed to save.
Maybe the whole registers needed to save can still be reduced.
Quoted 8 lines
I did not mean save/restore all registers. I just mean using only one symbol (struct or array). Though the struct or array contains some unused members, it saves many instructions in swsusp_arch_{suspend,resume}.
For saving N registers, (N * 2) instructions are required to save to individual variables, but (N + 2) instructions are required to save to array or struct.
Yes, the struct array method is more efficient, we will change to it.
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
arch/mips/power/cpu.c line 37
Quoted 5 lines
arch/mips/power/cpu.c new file +4
-0+void save_processor_state (void ) +{ + saved_status =read_c0_status (); +}No need to save/restore floating point registers?
Quoted 5 lines
Quoted 2 lines
the floating point registers are not used by kernel, for user part, they are already saved while entering into kernel mode.
No, floating point registers are not saved on entering into kernel. They are saved on context switch.
It's my mistake. But I think, if there is need to save floating point registers, the kernel have already done for it.
What's need to save should be for the resuming parts. Those registers which are used while in suspending path are needed to save.
create_image()
in_suspend = 1;
save_processor_state();
error = swsusp_arch_suspend();
if (error)
printk(KERN_ERR "PM: Error %d creating hibernation image\n",
error); when resuming this functions is executed for righ after the swsusp_arch_suspend(). This is not a normal function return.
So the registers need to save are those damaged by swsusp_arch_suspend and what it calls.
because this is not a normal function call, the callee saved registers can not be restored, so we need to save
it explicitly. For caller saved temporary registers, they are already saved in create_image. Are this right?
Quoted 3 lines
---
Atsushi Nemoto
Re: [loongson-PATCH-v1 22/27] Hibernation Support in mips system
Quoted 23 lines · yanh
Quoted 21 lines · 在 2009-05-23六的 21:30 +0900,Atsushi Nemoto写道:
Quoted 4 lines · yanh
Quoted 4 lines
Quoted 4 lines
arch/mips/power/cpu.c new file +3
-0+unsigned long + saved_ra, + saved_sp,...
Quoted 8 lines
Quoted 6 lines
arch/mips/power/cpu.c line 32
Quoted 3 lines
arch/mips/power/cpu.c new file +2
-0+ saved_v0, + saved_v1;Instead of enumerating them, I would prefer something like "struct
pt_regssaved_regs" or "unsigned long saved_regs[32]".This implementation is referencing the x86 platform. Not all the 32 reigsters are needed to save. Maybe the whole registers needed to save can still be reduced.
I did not mean save/restore all registers. I just mean using only one symbol (struct or array). Though the struct or array contains some unused members, it saves many instructions in swsusp_arch_{suspend,resume}.
Quoted 7 lines
Quoted 4 lines
For saving N registers, (N * 2) instructions are required to save to individual variables, but (N + 2) instructions are required to save to array or struct.
Yes, the struct array method is more efficient, we will change to it.
The length of registers is different between 32bit kernel and 64bit kernel. That means the file hibernate.S wiil be divided into hibernate_32.S and hibernate_64.S ?
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
arch/mips/power/cpu.c line 37
Quoted 5 lines
arch/mips/power/cpu.c new file +4
-0+void save_processor_state (void ) +{ + saved_status =read_c0_status (); +}No need to save/restore floating point registers?
Quoted 6 lines
Quoted 6 lines
Quoted 3 lines
the floating point registers are not used by kernel, for user part, they are already saved while entering into kernel mode.
No, floating point registers are not saved on entering into kernel. They are saved on context switch.
Yes, suspend to disk will freeze processes at first,and i think the process wiil save the float point regs. So there is no need to save them.
Quoted 12 lines
It's my mistake. But I think, if there is need to save floating point
registers, the kernel have already done for it. What's need to save should be for the resuming parts. Those registers which are used while in suspending path are needed to save.
create_image()in_suspend = 1; save_processor_state(); error = swsusp_arch_suspend(); if (error) printk(KERN_ERR "PM: Error %d creating hibernation image\n", error);
Quoted 8 lines
when resuming this functions is executed for righ after the
swsusp_arch_suspend(). This is not a normal function return.
So the registers need to save are those damaged byswsusp_arch_suspendand what it calls.because this is not a normal function call, the callee saved registers can not be restored, so we need to save
it explicitly. For caller saved temporary registers, they are already saved increate_image. Are this right?
---
Quoted 6 lines
Quoted 2 lines
Atsushi Nemoto
Signature · 8 lines
--------------------------------------------------------- Hongbing,Hu (Software Department) Tel: 0512-52308631 E-mail: [email protected] MSN: [[email protected]] JiangSu Lemote Corp. Ltd. MengLan, Yushan, Changshu, JiangSu Province, China ---------------------------------------------------------
Re: [loongson-PATCH-v1 24/27] fixup for FUJITSU disk
In reply to yanhQuoted 5 lines
Quoted 4 lines
In any case I have yet to see a CS5536 system whose BIOS sets the cable detection bit. If that's the problem I guess we could add a quirk flag to override the (lack of) BIOS setting.
This may be the cause that udma5 cannot be set.
If the system doesn't have working BIOS cable detect as per the documentation for the chip then just return the "unknown" cable type and libata will do device side cable detect.
Alan
Re: [loongson-PATCH-v1 24/27] fixup for FUJITSU disk
Quoted 10 lines · 在 2009-05-26二的 08:56 +0100,Alan Cox写道:
Quoted 5 lines
Quoted 4 lines
In any case I have yet to see a CS5536 system whose BIOS sets the cable detection bit. If that's the problem I guess we could add a quirk flag to override the (lack of) BIOS setting.
This may be the cause that udma5 cannot be set.
If the system doesn't have working BIOS cable detect as per the documentation for the chip then just return the "unknown" cable type and libata will do device side cable detect.
After force cable type as 80 wire, udma5 can be set OK now. after some raw test, the legacy and native driver have no obvious difference in performance.
Remain issue: this native driver still have suspend/resume issue.
Quoted 2 lines
Alan
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: [loongson-PATCH-v1 22/27] Hibernation Support in mips system
In reply to Hongbing HuQuoted 6 lines · Hongbing Hu
Quoted 2 lines
Yes, the struct array method is more efficient, we will change to it.
The length of registers is different between 32bit kernel and 64bit kernel.
That means the filehibernate.Swiil be divided intohibernate_32.Sandhibernate_64.S?
No, you can use macros in include/asm/asm.h to write common code for 32-bit/64-bit kernel.
Quoted 6 lines
Quoted 3 lines
Quoted 3 lines
No, floating point registers are not saved on entering into kernel. They are saved on context switch.
Yes, suspend to disk will freeze processes at first,and i think the process wiil save the float point regs.
So there is no need to save them.
Hmm, but the floating point registers in _current_ task are not saved (I think, but it this wrong?).
Maybe nobody might notice if ioctl() of the s2disk process clobbers floating point registers, but I think something like this is needed:
if (is_fpu_owner()) save_fp(current); if (cpu_has_dsp) save_dsp(p);
I'm not sure DSP part, and I also wonder other cp0 registers should be saved or not ...
---
Atsushi Nemoto
Re: [loongson-PATCH-v1 16/27] Add Siliconmotion 712 framebuffer driver
In reply to [email protected]Hi Wu Zhangjin
I applied your patch cleanly and run it on a i486SX (little endian) embedded computing board.
This provides a huge performance benefit compared to vesa framebuffer, so thanks a lot for the contribution.
I tested it in both the library-accelerated (cfb...) and hardware accelerated codepaths, with no problems. Tested with qt-embedded 4.5.1.
As i have seen lots of functionality are guarded by #ifdef __BIG_ENDIAN
Is there a way to setup a different mode than 1024x600 on kernel-commandline or from userspace, e.g. with fbset?
What I currently do is
picking appropriate values form the table VGAMode in smtcfb.h and hardcoding them.
I tried 800x600x16bit@60hz, which worked also, but 1024x768x24bit@60hz left me with a corrupted display output (distored colors, missing regions), i did not check further wheter it also crashed.
I dont know wheter i am subscribed and this will make it through to lkml and linux-mips, feel free to cite me if you want.
Also if you want you may add my
see also attached a patch for the debug messages
From addec9a5a27512621c538a2f799e31e07720cb9c Mon Sep 17 00:00:00 2001
From: Simon Braunschmidt <[email protected]>
Date: Fri, 29 May 2009 15:03:51 +0200
Subject: [PATCH] [video] fix debug messages in smtcfb
when defining #DEBUG
--- drivers/video/smi/smtcfb.c | 6 ++++-- 1 files changed, 4 insertions(+), 2 deletions(-)
drivers/video/smi/smtcfb.c +4 -2
@@ -44,6 +44,8 @@#include "smtcfb.h" #include "smtc2d.h" +#define DEBUG +#ifdef DEBUG #define smdbg(format, arg...) printk(KERN_DEBUG format , ## arg)#else
@@ -1087,7 +1089,7 @@ static int __init sm712be_setup(char *options) sm712be_flag =0 ;if (!options || !*options) { retval =1 ; -smdbg ("\n No sm712be parameter\n" , __LINE__); +smdbg ("\n No sm712be parameter\n" ); }if (!retval &&strstr (options,"enable" )) sm712be_flag =1 ;
@@ -1113,7 +1115,7 @@ static int __init sm712vga_setup(char *options)if (!options || !*options) { retval =1 ; -smdbg ("\n No vga parameter\n" , __LINE__); +smdbg ("\n No vga parameter\n" ); } screen_info.lfb_width =0 ;
--
1.6.3.rc0.1.gf800
Wu Zhangjin
AppliedRe: [loongson-PATCH-v1 16/27] Add Siliconmotion 712 framebuffer driver
Hi,
Quoted 4 lines · Simon Braunschmidt
Hi Wu Zhangjin
I applied your patch cleanly and run it on a i486SX (little endian) embedded computing board.
thanks very much for testing it in a non-mips platform!
Quoted 3 lines
This provides a huge performance benefit compared to vesa framebuffer, so thanks a lot for the contribution.
the thanks should goes to the original authors from Silicon Motion Technology Corp. including Ge Wang and Boyod.Yang. I just cleaned it up.
Quoted 9 lines
I tested it in both the library-accelerated (cfb...) and hardware accelerated codepaths, with no problems. Tested with qt-embedded 4.5.1.
As i have seen lots of functionality are guarded by #ifdef
__BIG_ENDIANIs there a way to setup a different mode than 1024x600 on kernel-commandline or from userspace, e.g. with fbset?
seems we can change it in userspace, i have changed it to 800X480 in a 7inch yeeloong2f laptop in the "control center" of KDE desktop.
or perhaps you can configure it in the Xorg.conf directly.
Quoted 8 lines
What I currently do is
picking appropriate values form the table VGAMode insmtcfb.hand hardcoding them.I tried 800x600x16bit@60hz, which worked also, but 1024x768x24bit@60hz left me with a corrupted display output (distored colors, missing regions), i did not check further wheter it also crashed.
I will try to check it, but in reality, I'm not familiar with it, so maybe very hard and slow to check it. I will forward this E-mail to the original authors, hope they can give some help.
Quoted 7 lines
I dont know wheter i am subscribed and this will make it through to lkml and linux-mips, feel free to cite me if you want.
Also if you want you may add my
Tested-by Simon Braunschmidt <[email protected]>
added.
Quoted 4 lines
see also attached a patch for the debug messages
Applied.
thanks!
Wu Zhangjin
Quoted 47 lines
From
addec9a5a27512621c538a2f799e31e07720cb9cMon Sep 17 00:00:00 2001
From: Simon Braunschmidt <[email protected]>
Date: Fri, 29 May 2009 15:03:51 +0200
Subject: [PATCH] [video] fix debug messages in smtcfbwhen defining #DEBUG
--- drivers/video/smi/smtcfb.c | 6 ++++-- 1 files changed, 4 insertions(+), 2 deletions(-)drivers/video/smi/smtcfb.c +4
-3@@ -44,6 +44,8 @@#include "smtcfb.h" #include "smtc2d.h" +#define DEBUG +#ifdef DEBUG #define smdbg(format, arg...) printk(KERN_DEBUG format , ## arg)#else @@ -1087,7 +1089,7 @@ static int __init sm712be_setup(char *options) sm712be_flag =0 ;if (!options || !*options) { retval =1 ; -smdbg ("\n No sm712be parameter\n" , __LINE__); +smdbg ("\n No sm712be parameter\n" ); }if (!retval &&strstr (options,"enable" )) sm712be_flag =1 ;@@ -1113,7 +1115,7 @@ static int __init sm712vga_setup(char *options)if (!options || !*options) { retval =1 ; -smdbg ("\n No vga parameter\n" , __LINE__); +smdbg ("\n No vga parameter\n" ); } screen_info.lfb_width =0 ; --1.6.3.rc0.1.gf800
Re: [loongson-PATCH-v1 16/27] Add Siliconmotion 712 framebuffer driver
In reply to Simon Braunschmidthi,
Quoted 6 lines
As i have seen lots of functionality are guarded by #ifdef
__BIG_ENDIANIs there a way to setup a different mode than 1024x600 on kernel-commandline or from userspace, e.g. with fbset?
I just removed some of #ifdef __BIG_ENDIAN ... #endif, and tuned the vesa_mode values, now, we can pass it in kernel-commandline like this:
vga=1024x600x24
the latest SMI video driver patch with this modification will be sent out later, but you can get this one if you need it immediately:
From 34e4afa8b64f794e4fef0dd622ef576dbfecc851 Mon Sep 17 00:00:00 2001
From: Wu Zhangjin <[email protected]>
Date: Mon, 1 Jun 2009 15:31:26 +0800
Subject: [PATCH] enable the vga command line in SMI video driver
there is no need to define a screen_info again so remove it, because it is defined in arch/mips/kernel/setup.c and not relative to big endian or little endian, and here I think its better use something like 1024x600x24 than 0x318, so replace all of the magic numbers to an understandable one.
--- drivers/video/smi/smtcfb.c | 42 ++++++++++++++++++------------------------ 1 files changed, 18 insertions(+), 24 deletions(-)
drivers/video/smi/smtcfb.c +18 -24
@@ -52,10 +52,6 @@ #define smdbg(format, arg...)#endif -#ifdef __BIG_ENDIAN -struct screen_info screen_info; -#endif -/* * Private structure */
@@ -96,32 +92,32 @@ struct par_info {u8 chipRevID; }; -#ifdef __BIG_ENDIANstruct vesa_mode_table { -char mode_index[6 ]; +char mode_index[15 ];u16 lfb_width;u16 lfb_height;u16 lfb_depth; };static struct vesa_mode_table vesa_mode[] = { - {"0x301" ,640 ,480 ,8 }, - {"0x303" ,800 ,600 ,8 }, - {"0x305" ,1024 ,768 ,8 }, - {"0x307" ,1280 ,1024 ,8 }, - - {"0x311" ,640 ,480 ,16 }, - {"0x314" ,800 ,600 ,16 }, - {"0x317" ,1024 ,768 ,16 }, - {"0x31A" ,1280 ,1024 ,16 }, - - {"0x312" ,640 ,480 ,24 }, - {"0x315" ,800 ,600 ,24 }, - {"0x318" ,1024 ,768 ,24 }, - {"0x31B" ,1280 ,1024 ,24 }, - + {"640x480x8" ,640 ,480 ,8 }, + {"800x480x8" ,800 ,480 ,8 }, + {"800x600x8" ,800 ,600 ,8 }, + {"1024x768x8" ,1024 ,768 ,8 }, + {"1280x1024x8" ,1280 ,1024 ,8 }, + + {"640x480x16" ,640 ,480 ,16 }, + {"800x480x16" ,800 ,480 ,16 }, + {"800x600x16" ,800 ,600 ,16 }, + {"1024x768x16" ,1024 ,768 ,16 }, + {"1280x1024x16" ,1280 ,1024 ,16 }, + + {"640x480x24" ,640 ,480 ,24 }, + {"800x480x24" ,800 ,480 ,24 }, + {"800x600x24" ,800 ,600 ,24 }, + {"1024x768x24" ,1024 ,768 ,24 }, + {"1280x1024x24" ,1280 ,1024 ,24 }, }; -#endif char __iomem *smtc_RegBaseAddress;/* Memory Map IO starting address */ char __iomem *smtc_VRAMBaseAddress;/* video memory starting address */
@@ -1100,7 +1096,6 @@ static int __init sm712be_setup(char *options)__setup ("sm712be=" , sm712be_setup); -#ifdef __BIG_ENDIAN/* * sm712vga_setup - process command line options, get vga parameter * @options: string of options
@@ -1136,7 +1131,6 @@ static int __init sm712vga_setup(char *options) }__setup ("vga=" , sm712vga_setup); -#endif MODULE_AUTHOR ("Siliconmotion " );MODULE_DESCRIPTION ("Framebuffer driver for SMI Graphic Cards" );
Signature · 10 lines
1.6.0.4 with the support of this patch, the users of 7inch yeeloong and 8.9inch yeeloong can use the same kernel(not totally, the shutdown logic is a little different, a patch is also ready for it). there is only a need to add such kernel command line for 7inch yeeloong: vga=800x480x24
Quoted 8 lines
What I currently do is
picking appropriate values form the table VGAMode insmtcfb.hand hardcoding them.I tried 800x600x16bit@60hz, which worked also, but 1024x768x24bit@60hz left me with a corrupted display output (distored colors, missing regions), i did not check further wheter it also crashed.
no all of the Vesa mode is suitable to your screen, you should choose one for you, for example, only 800x480 is suitable to yeeloong 7inch screen, but the 8.9 inch yeeloong, need 1024x600.
best regards,
Wu Zhangjin