README.hardware: update the beagleboard serial port documentation
PATCH 1/1 README.hardware: update the beagleboard serial port documentation
In reply to a message not in the archiveFrom: Darren Hart <[email protected]>
Pull URL: git://git.pokylinux.org/poky-contrib.git
Branch: dvhart/beagle
Browse: http://git.pokylinux.org/cgit.cgi/poky-contrib/log/?h=dvhart/beagle
Thanks,
Darren Hart <[email protected]>
Update the README.hardware beagleboard description to account for the use of the OMAP_SERIAL in recent kernel recipes. Add a note documenting how to use the old 8250 based serial devices for older kernels.
Correct a type.
Correct the boot script name from user.scr to boot.scr.
--- README.hardware | 16 ++++++++++++---- 1 files changed, 12 insertions(+), 4 deletions(-)
README.hardware +12 -4
@@ -519,7 +519,7 @@ TODO: need someone with a Beagleboard C4 to verify these instructions. Due to the lack of NAND on the xM, the install and boot process varies a bit between boards. The C4 can run the x-loader and u-boot binaries from NAND or the SD, while the xM can only run them from the SD. The following instructions -apply to both the C4 and the xM, but te C4 can skip step 2 (as noted below), +apply to both the C4 and the xM, but the C4 can skip step 2 (as noted below), and may require modification of the NAND environment. 1. Partition and format an SD card:
@@ -564,11 +564,19 @@ and may require modification of the NAND environment. # (cat << EOF setenv bootcmd 'mmc init; fatload mmc 0:1 0x80300000 uImage; bootm 0x80300000' - setenv bootargs 'console=tty0 console=ttyS2,115200n8 root=/dev/mmcblk0p2 rootwait rootfstype=ext3 ro' + setenv bootargs 'console=tty0 console=ttyO2,115200n8 root=/dev/mmcblk0p2 rootwait rootfstype=ext3 ro' boot EOF ) > serial-boot.cmd - # mkimage -A arm -O linux -T script -C none -a 0 -e 0 -n "Poky Minimal" -d ./serial-boot.cmd ./user.scr - # cp user.scr /media/boot + # mkimage -A arm -O linux -T script -C none -a 0 -e 0 -n "Poky Minimal" -d ./serial-boot.cmd ./boot.scr + # cp boot.scr /media/boot 6. Unmount the SD partitions and boot the Beagleboard + +Note: As of the 2.6.37 linux-yocto kernel recipe, the Beagleboard uses the + OMAP_SERIAL device (ttyO2). If you are using an older kernel, such as the + 2.6.35 linux-yocto-stable, be sure replace ttyO2 with ttyS2 above. You + should also override the machine SERIAL_CONSOLE in your local.conf in + order to setup the getty on the serial line: + + SERIAL_CONSOLE_beagleboard = "115200 ttyS2"
Signature · 1 line
1.7.0.4
Richard Purdie
AppliedQuoted 13 lines · Darren Hart
From: Darren Hart <[email protected]>
Pull URL:
git://git.pokylinux.org/poky-contrib.git
Branch: dvhart/beagle
Browse: http://git.pokylinux.org/cgit.cgi/poky-contrib/log/?h=dvhart/beagleThanks,
Darren Hart <[email protected]>Update the README.hardware beagleboard description to account for the use of the
OMAP_SERIALin recent kernel recipes. Add a note documenting how to use the old 8250 based serial devices for older kernels.
Quoted 6 lines
Correct a type.
Correct the boot script name from user.scr to boot.scr.
Signed-off-by Darren Hart <[email protected]>CC Gary Thomas <[email protected]>
Merged to master, thanks.
Richard