ARM: Kirkwood: Iomega ix2-200 DT support Signed-off-by: Alan M Butler <[email protected]>

Patch version 5.
Add support for the Iomega ix2-200.
Led's and buttons working as of kernel 3.6-rc2

the 3 lines in the network interface do seem to be required as removing either causes the network card to not be able to reach the network (at least on my device).

Product page:
http://go.iomega.com/en/products/network-storage-desktop/storcenter-network-storage-solution/network-hard-drive-ix2-200-cloud/?partner=4735#tech_specsItem_tab

Signed-off-by Alan M Butler <[email protected]>

---
 arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts |  105 +++++++++++++++++++++++++
 arch/arm/mach-kirkwood/Kconfig                |    7 ++
 arch/arm/mach-kirkwood/Makefile               |    1 +
 arch/arm/mach-kirkwood/Makefile.boot          |    1 +
 arch/arm/mach-kirkwood/board-dt.c             |    4 +
 arch/arm/mach-kirkwood/board-iomega_ix2_200.c |   57 ++++++++++++++
 arch/arm/mach-kirkwood/common.h               |    6 ++
 7 files changed, 181 insertions(+)
 create mode 100644 arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
 create mode 100644 arch/arm/mach-kirkwood/board-iomega_ix2_200.c

arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts new file +105 -0

new file mode 100644
index 0000000..865aeec
@@ -0,0 +1,105 @@
+/dts-v1/;
+
+/include/ "kirkwood.dtsi"
+
+/ {
+	model = "Iomega StorCenter ix2-200";
+	compatible = "iom,ix2-200", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk";
+	};
+
+	ocp at f1000000 {
+		i2c at 11000 {
+			status = "okay";
+
+			lm63: lm63 at 4c {
+				compatible = "national,lm63";
+				reg = <0x4c>;
+			};
+		};
+
+		serial at 12000 {
+			clock-frequency = <200000000>;
+			status = "ok";
+		};
+
+		nand at 3000000 {
+			status = "okay";
+
+			partition at 0 {
+				label = "u-boot";
+				reg = <0x0000000 0x100000>;
+				read-only;
+			};
+
+			partition at a0000 {
+				label = "env";
+				reg = <0xa0000 0x20000>;
+				read-only;
+			};
+
+			partition at 100000 {
+				label = "uImage";
+				reg = <0x100000 0x300000>;
+			};
+
+			partition at 400000 {
+				label = "uInitrd";
+				reg = <0x540000 0x1000000>;
+			};
+		};
+		sata at 80000 {
+			status = "okay";
+			nr-ports = <2>;
+		};
+
+	};
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		power_led {
+			label = "status:white:power_led";
+			gpios = <&gpio0 16 0>;
+			linux,default-trigger = "default-on";
+		};
+		health_led1 {
+			label = "status:red:health_led";
+			gpios = <&gpio1 5 0>;
+		};
+		health_led2 {
+			label = "status:white:health_led";
+			gpios = <&gpio1 4 0>;
+		};
+		backup_led {
+			label = "status:blue:backup_led";
+			gpios = <&gpio0 15 0>;
+		};
+	};
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		Power {
+			label = "Power Button";
+			linux,code = <116>;
+			gpios = <&gpio0 14 1>;
+		};
+		Reset {
+			label = "Reset Button";
+			linux,code = <0x198>;
+			gpios = <&gpio0 12 1>;
+		};
+		OTB {
+			label = "OTB Button";
+			linux,code = <133>;
+			gpios = <&gpio1 3 1>;
+		};
+	};
+};

arch/arm/mach-kirkwood/Kconfig +7 -0

index ca5c15a..bee8451 100644
@@ -195,6 +195,13 @@ config MACH_T5325
 	  Say 'Y' here if you want your kernel to support the
 	  HP t5325 Thin Client.
 
+config MACH_IOMEGA_IX2_200_DT
+	bool "Iomega StorCenter ix2-200 (Flattened Device Tree)"
+	select ARCH_KIRKWOOD_DT
+	help
+	  Say 'Y' here if you want your kernel to support the
+	  Iomega StorCenter ix2-200 (Flattened Device Tree).
+
 endmenu
 
 endif

arch/arm/mach-kirkwood/Makefile +1 -0

index 055c85a..f5484dc 100644
@@ -28,3 +28,4 @@ obj-$(CONFIG_MACH_IB62X0_DT)		+= board-ib62x0.o
 obj-$(CONFIG_MACH_TS219_DT)		+= board-ts219.o tsx1x-common.o
 obj-$(CONFIG_MACH_GOFLEXNET_DT)		+= board-goflexnet.o
 obj-$(CONFIG_MACH_LSXL_DT)		+= board-lsxl.o
+obj-$(CONFIG_MACH_IOMEGA_IX2_200_DT)	+= board-iomega_ix2_200.o

arch/arm/mach-kirkwood/Makefile.boot +1 -0

index a571755..59b719d 100644
@@ -11,3 +11,4 @@ dtb-$(CONFIG_MACH_TS219_DT)	+= kirkwood-qnap-ts219.dtb
 dtb-$(CONFIG_MACH_GOFLEXNET_DT) += kirkwood-goflexnet.dtb
 dtb-$(CONFIG_MACH_LSXL_DT) += kirkwood-lschlv2.dtb
 dtb-$(CONFIG_MACH_LSXL_DT) += kirkwood-lsxhl.dtb
+dtb-$(CONFIG_MACH_IOMEGA_IX2_200_DT) += kirkwood-iomega_ix2_200.dtb

arch/arm/mach-kirkwood/board-dt.c +4 -0

index e4eb450..9b3ec17 100644
@@ -87,6 +87,9 @@ static void __init kirkwood_dt_init(void)
 	if (of_machine_is_compatible("buffalo,lsxl"))
 		lsxl_init();
 
+	if (of_machine_is_compatible("iom,ix2-200"))
+		iomega_ix2_200_init();
+
 	of_platform_populate(NULL, kirkwood_dt_match_table,
 			     kirkwood_auxdata_lookup, NULL);
 }

@@ -100,6 +103,7 @@ static const char *kirkwood_dt_board_compat[] = {
 	"qnap,ts219",
 	"seagate,goflexnet",
 	"buffalo,lsxl",
+	"iom,ix2-200",
 	NULL
 };
 

arch/arm/mach-kirkwood/board-iomega_ix2_200.c new file +57 -0

new file mode 100644
index 0000000..158fb97
@@ -0,0 +1,57 @@
+/*
+ * arch/arm/mach-kirkwood/board-iomega_ix2_200.c
+ *
+ * Iomega StorCenter ix2-200
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mv643xx_eth.h>
+#include <linux/ethtool.h>
+#include <mach/kirkwood.h>
+#include "common.h"
+#include "mpp.h"
+
+static struct mv643xx_eth_platform_data iomega_ix2_200_ge00_data = {
+	.phy_addr       = MV643XX_ETH_PHY_NONE,
+	.speed          = SPEED_1000,
+	.duplex         = DUPLEX_FULL,
+};
+
+static unsigned int iomega_ix2_200_mpp_config[] __initdata = {
+	MPP12_GPIO,			/* Reset Button */
+	MPP14_GPIO,			/* Power Button */
+	MPP15_GPIO,			/* Backup LED (blue) */
+	MPP16_GPIO,			/* Power LED (white) */
+	MPP35_GPIO,			/* OTB Button */
+	MPP36_GPIO,			/* Rebuild LED (white) */
+	MPP37_GPIO,			/* Health LED (red) */
+	MPP38_GPIO,			/* SATA LED brightness control 1 */
+	MPP39_GPIO,			/* SATA LED brightness control 2 */
+	MPP40_GPIO,			/* Backup LED brightness control 1 */
+	MPP41_GPIO,			/* Backup LED brightness control 2 */
+	MPP42_GPIO,			/* Power LED brightness control 1 */
+	MPP43_GPIO,			/* Power LED brightness control 2 */
+	MPP44_GPIO,			/* Health LED brightness control 1 */
+	MPP45_GPIO,			/* Health LED brightness control 2 */
+	MPP46_GPIO,			/* Rebuild LED brightness control 1 */
+	MPP47_GPIO,			/* Rebuild LED brightness control 2 */
+	0
+};
+
+void __init iomega_ix2_200_init(void)
+{
+	/*
+	 * Basic setup. Needs to be called early.
+	 */
+	kirkwood_mpp_conf(iomega_ix2_200_mpp_config);
+
+	kirkwood_ehci_init();
+
+	kirkwood_ge01_init(&iomega_ix2_200_ge00_data);
+}

arch/arm/mach-kirkwood/common.h +6 -0

index 304dd1a..d5d4064 100644
@@ -94,6 +94,12 @@ void lsxl_init(void);
 static inline void lsxl_init(void) {};
 #endif
 
+#ifdef CONFIG_MACH_IOMEGA_IX2_200_DT
+void iomega_ix2_200_init(void);
+#else
+static inline void iomega_ix2_200_init(void) {};
+#endif
+
 /* early init functions not converted to fdt yet */
 char *kirkwood_id(void);
 void kirkwood_l2_init(void);

Signature · 1 line

1.7.9.5

Patch version 5.
Add support for the Iomega ix2-200.
Led's and buttons working as of kernel 3.6-rc2

the 3 lines in the network interface do seem to be required as removing either causes the network card to not be able to reach the network (at least on my device).

Product page:
http://go.iomega.com/en/products/network-storage-desktop/storcenter-network-storage-solution/network-hard-drive-ix2-200-cloud/?partner=4735#tech_specsItem_tab

Signed-off-by Alan M Butler <[email protected]>