drm/i915: Baytrail MIPI DSI support

PATCH Superseded Jani Nikula 4 participants 20 messages Aug 13, 2013 – Aug 15, 2013

Subsystems (3)

DRM drivers DRM misc Intel i915

lore

Share & tools

lore

Jani Nikula

author

2013-08-13 13:28 UTC #0 lore raw

cover drm/i915: Baytrail MIPI DSI support

Hi all -

This series adds rudimentary MIPI DSI support to Baytrail. It's been built around the idea of panel specific sub-encoders, similar to the DVO support we have. This work is by no means complete; there are plenty of rough edges, but it should be a somewhat sane start to build upon.

I'm aware of the Common Display Framework and drm_bridge patches. In the future, I expect our DSI support to be ported over to whatever eventually comes out of them. In the mean time, we can't wait for them to be completed, and I believe it would be helpful for that effort to have our bits and pieces upstream.

The last patch is provided as an (incomplete) example of a sub-encoder, or a panel driver. It should *not* be merged. There's no proper detection or VBT handling yet, so that will cause warnings about inconsistent crtc/pll states...

BR,
Jani.

Jani Nikula (9):
drm/i915: add more VLV IOSF sideband ports accessors drm/i915: add VLV pipeconf bit definition for DSI PLL lock drm/i915: add MIPI DSI register definitions drm/i915: add MIPI DSI output type and subtypes drm/i915: add structs for MIPI DSI output drm/i915: add MIPI DSI command sending routines drm/i915: add basic MIPI DSI output support drm/i915: don't enable DPLL for DSI
drm/i915: initialize DSI output on VLV

Shobhit Kumar (4):
drm: add MIPI DSI encoder and connector types
drm/i915: Band Gap WA
drm/i915: Parse the MIPI related VBT Block and store relevant info drm/i915: add AUO MIPI DSI display sub-encoder

ymohanma (1):
drm/i915: add VLV DSI PLL Calculations

 drivers/gpu/drm/drm_crtc.c             |    2 +
 drivers/gpu/drm/i915/Makefile          |    4 +
 drivers/gpu/drm/i915/auo_dsi_display.c |  182 ++++++++++
 drivers/gpu/drm/i915/i915_drv.h        |   13 +
 drivers/gpu/drm/i915/i915_reg.h        |  424 ++++++++++++++++++++++
 drivers/gpu/drm/i915/intel_bios.c      |   16 +
 drivers/gpu/drm/i915/intel_bios.h      |   41 +++
 drivers/gpu/drm/i915/intel_display.c   |   52 ++-
 drivers/gpu/drm/i915/intel_drv.h       |    7 +-
 drivers/gpu/drm/i915/intel_dsi.c       |  606 ++++++++++++++++++++++++++++++++
 drivers/gpu/drm/i915/intel_dsi.h       |  104 ++++++
 drivers/gpu/drm/i915/intel_dsi_cmd.c   |  442 +++++++++++++++++++++++
 drivers/gpu/drm/i915/intel_dsi_cmd.h   |  109 ++++++
 drivers/gpu/drm/i915/intel_dsi_pll.c   |  290 +++++++++++++++
 drivers/gpu/drm/i915/intel_sideband.c  |   56 +++
 include/uapi/drm/drm_mode.h            |    2 +
 16 files changed, 2330 insertions(+), 20 deletions(-)
 create mode 100644 drivers/gpu/drm/i915/auo_dsi_display.c
 create mode 100644 drivers/gpu/drm/i915/intel_dsi.c
 create mode 100644 drivers/gpu/drm/i915/intel_dsi.h
 create mode 100644 drivers/gpu/drm/i915/intel_dsi_cmd.c
 create mode 100644 drivers/gpu/drm/i915/intel_dsi_cmd.h
 create mode 100644 drivers/gpu/drm/i915/intel_dsi_pll.c

Signature · 1 line

1.7.9.5

Jani Nikula

author

2013-08-13 13:28 UTC #1 lore raw

PATCH 1/14 drm: add MIPI DSI encoder and connector types

From: Shobhit Kumar <[email protected]>

Signed-off-by Shobhit Kumar <[email protected]>

Signed-off-by Jani Nikula <[email protected]>

---
 drivers/gpu/drm/drm_crtc.c  |    2 ++
 include/uapi/drm/drm_mode.h |    2 ++
 2 files changed, 4 insertions(+)

drivers/gpu/drm/drm_crtc.c +2 -0

index fc83bb9..8768c5f 100644
@@ -209,6 +209,7 @@ static struct drm_conn_prop_enum_list drm_connector_enum_list[] =
 	{ DRM_MODE_CONNECTOR_TV, "TV", 0 },
 	{ DRM_MODE_CONNECTOR_eDP, "eDP", 0 },
 	{ DRM_MODE_CONNECTOR_VIRTUAL, "Virtual", 0},
+	{ DRM_MODE_CONNECTOR_DSI, "DSI", 0},
 };
 
 static const struct drm_prop_enum_list drm_encoder_enum_list[] =

@@ -218,6 +219,7 @@ static const struct drm_prop_enum_list drm_encoder_enum_list[] =
 	{ DRM_MODE_ENCODER_LVDS, "LVDS" },
 	{ DRM_MODE_ENCODER_TVDAC, "TV" },
 	{ DRM_MODE_ENCODER_VIRTUAL, "Virtual" },
+	{ DRM_MODE_ENCODER_DSI, "DSI" },
 };
 
 const char *drm_get_encoder_name(const struct drm_encoder *encoder)

include/uapi/drm/drm_mode.h +2 -0

index 53db7ce..589114e 100644
@@ -165,6 +165,7 @@ struct drm_mode_get_plane_res {
 #define DRM_MODE_ENCODER_LVDS	3
 #define DRM_MODE_ENCODER_TVDAC	4
 #define DRM_MODE_ENCODER_VIRTUAL 5
+#define DRM_MODE_ENCODER_DSI	6
 
 struct drm_mode_get_encoder {
 	__u32 encoder_id;

@@ -203,6 +204,7 @@ struct drm_mode_get_encoder {
 #define DRM_MODE_CONNECTOR_TV		13
 #define DRM_MODE_CONNECTOR_eDP		14
 #define DRM_MODE_CONNECTOR_VIRTUAL      15
+#define DRM_MODE_CONNECTOR_DSI		16
 
 struct drm_mode_get_connector {

Signature · 1 line

1.7.9.5

Jani Nikula

author

2013-08-13 13:28 UTC #2 lore raw

PATCH 2/14 drm/i915: add more VLV IOSF sideband ports accessors

In reply to Jani Nikula

For GPIO NC, CCK, CCU, and GPS CORE.

Signed-off-by Jani Nikula <[email protected]>

Signed-off-by Shobhit Kumar <[email protected]>

---
 drivers/gpu/drm/i915/i915_drv.h       |    8 +++++
 drivers/gpu/drm/i915/i915_reg.h       |    4 +++
 drivers/gpu/drm/i915/intel_sideband.c |   56 +++++++++++++++++++++++++++++++++
 3 files changed, 68 insertions(+)

drivers/gpu/drm/i915/i915_drv.h +8 -0

index dcae809..6db95a2 100644
@@ -2164,6 +2164,14 @@ int sandybridge_pcode_write(struct drm_i915_private *dev_priv, u8 mbox, u32 val)
 u32 vlv_punit_read(struct drm_i915_private *dev_priv, u8 addr);
 void vlv_punit_write(struct drm_i915_private *dev_priv, u8 addr, u32 val);
 u32 vlv_nc_read(struct drm_i915_private *dev_priv, u8 addr);
+u32 vlv_gpio_nc_read(struct drm_i915_private *dev_priv, u32 reg);
+void vlv_gpio_nc_write(struct drm_i915_private *dev_priv, u32 reg, u32 val);
+u32 vlv_cck_read(struct drm_i915_private *dev_priv, u32 reg);
+void vlv_cck_write(struct drm_i915_private *dev_priv, u32 reg, u32 val);
+u32 vlv_ccu_read(struct drm_i915_private *dev_priv, u32 reg);
+void vlv_ccu_write(struct drm_i915_private *dev_priv, u32 reg, u32 val);
+u32 vlv_gps_core_read(struct drm_i915_private *dev_priv, u32 reg);
+void vlv_gps_core_write(struct drm_i915_private *dev_priv, u32 reg, u32 val);
 u32 vlv_dpio_read(struct drm_i915_private *dev_priv, int reg);
 void vlv_dpio_write(struct drm_i915_private *dev_priv, int reg, u32 val);
 u32 intel_sbi_read(struct drm_i915_private *dev_priv, u16 reg,

drivers/gpu/drm/i915/i915_reg.h +4 -0

index 17f6252..a30e876 100644
@@ -360,6 +360,10 @@
 #define   IOSF_PORT_PUNIT			0x4
 #define   IOSF_PORT_NC				0x11
 #define   IOSF_PORT_DPIO			0x12
+#define   IOSF_PORT_GPIO_NC			0x13
+#define   IOSF_PORT_CCK				0x14
+#define   IOSF_PORT_CCU				0xA9
+#define   IOSF_PORT_GPS_CORE			0x48
 #define VLV_IOSF_DATA				(VLV_DISPLAY_BASE + 0x2104)
 #define VLV_IOSF_ADDR				(VLV_DISPLAY_BASE + 0x2108)

drivers/gpu/drm/i915/intel_sideband.c +56 -0

62 lines not on this page · raw message

Signature · 1 line

1.7.9.5

Jani Nikula

author

2013-08-13 13:28 UTC #3 lore raw

PATCH 3/14 drm/i915: add VLV pipeconf bit definition for DSI PLL lock

In reply to Jani Nikula

Signed-off-by Jani Nikula <[email protected]>

---
 drivers/gpu/drm/i915/i915_reg.h |    1 +
 1 file changed, 1 insertion(+)

drivers/gpu/drm/i915/i915_reg.h +1 -0

index a30e876..aced53a 100644
@@ -2972,6 +2972,7 @@
 #define   PIPECONF_DISABLE	0
 #define   PIPECONF_DOUBLE_WIDE	(1<<30)
 #define   I965_PIPECONF_ACTIVE	(1<<30)
+#define   PIPECONF_DSI_PLL_LOCKED	(1<<29) /* vlv only */
 #define   PIPECONF_FRAME_START_DELAY_MASK (3<<27)
 #define   PIPECONF_SINGLE_WIDE	0
 #define   PIPECONF_PIPE_UNLOCKED 0

Signature · 1 line

1.7.9.5

Jani Nikula

author

2013-08-13 13:28 UTC #4 lore raw

PATCH 4/14 drm/i915: add MIPI DSI register definitions

In reply to Jani Nikula

Add definitions for VLV MIPI DSI registers.

Signed-off-by Jani Nikula <[email protected]>

---
 drivers/gpu/drm/i915/i915_reg.h |  409 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 409 insertions(+)

drivers/gpu/drm/i915/i915_reg.h +409 -0

index aced53a..32e32b6 100644
@@ -5104,4 +5104,413 @@
 #define PIPE_CSC_POSTOFF_ME(pipe) _PIPE(pipe, _PIPE_A_CSC_POSTOFF_ME, _PIPE_B_CSC_POSTOFF_ME)
 #define PIPE_CSC_POSTOFF_LO(pipe) _PIPE(pipe, _PIPE_A_CSC_POSTOFF_LO, _PIPE_B_CSC_POSTOFF_LO)
 
+/* VLV MIPI registers */
+
+/* XXX: This register seems very messy. MIPIB has only enable and delay. */
+#define _MIPIA_PORT_CTRL			(VLV_DISPLAY_BASE + 0x61190)
+#define _MIPIB_PORT_CTRL			(VLV_DISPLAY_BASE + 0x61700)
+#define MIPI_PORT_CTRL(pipe)		_PIPE(pipe, _MIPIA_PORT_CTRL, _MIPIB_PORT_CTRL)
+#define  DPI_ENABLE					(1 << 31) /* A + B */
+#define  MIPIA_MIPI4DPHY_DELAY_COUNT_SHIFT		27
+#define  MIPIA_MIPI4DPHY_DELAY_COUNT_MASK		(0xf << 27)
+#define  DUAL_LINK_MODE_MASK				(1 << 26)
+#define  DUAL_LINK_MODE_FRONT_BACK			(0 << 26)
+#define  DUAL_LINK_MODE_PIXEL_ALTERNATIVE		(1 << 26)
+#define  FLOPPED_HSTX					(1 << 23)
+#define  DE_INVERT					(1 << 19) /* XXX */
+#define  MIPIA_FLISDSI_DELAY_COUNT_SHIFT		18
+#define  MIPIA_FLISDSI_DELAY_COUNT_MASK			(0xf << 18)
+#define  AFE_LATCHOUT					(1 << 17)
+#define  MIPIB_FLISDSI_DELAY_COUNT_HIGH_SHIFT		15
+#define  MIPIB_FLISDSI_DELAY_COUNT_HIGH_MASK		(1 << 15)
+#define  MIPIB_MIPI4DPHY_DELAY_COUNT_SHIFT		11
+#define  MIPIB_MIPI4DPHY_DELAY_COUNT_MASK		(0xf << 11)
+#define  CSB_SHIFT					9
+#define  CSB_MASK					(3 << 9)
+#define  CSB_20MHZ					(0 << 9)
+#define  CSB_10MHZ					(1 << 9)
+#define  CSB_40MHZ					(2 << 9)
+#define  BANDGAP_MASK					(1 << 8)
+#define  BANDGAP_PNW_CIRCUIT				(0 << 8)
+#define  BANDGAP_LNC_CIRCUIT				(1 << 8)
+#define  MIPIB_FLISDSI_DELAY_COUNT_LOW_SHIFT		5
+#define  MIPIB_FLISDSI_DELAY_COUNT_LOW_MASK		(7 << 5)
+#define  TEARING_EFFECT_DELAY				(1 << 4) /* A + B */
+#define  TEARING_EFFECT_SHIFT				2 /* A + B */
+#define  TEARING_EFFECT_MASK				(3 << 2)
+#define  TEARING_EFFECT_OFF				(0 << 2)
+#define  TEARING_EFFECT_DSI				(1 << 2)
+#define  TEARING_EFFECT_GPIO				(2 << 2)
+#define  LANE_CONFIGURATION_SHIFT			0
+#define  LANE_CONFIGURATION_MASK			(3 << 0)
+#define  LANE_CONFIGURATION_4LANE			(0 << 0)
+#define  LANE_CONFIGURATION_DUAL_LINK_A			(1 << 0)
+#define  LANE_CONFIGURATION_DUAL_LINK_B			(2 << 0)
+
+#define _MIPIA_TEARING_CTRL			(VLV_DISPLAY_BASE + 0x61194)
+#define _MIPIB_TEARING_CTRL			(VLV_DISPLAY_BASE + 0x61704)
+#define MIPI_TEARING_CTRL(pipe)		_PIPE(pipe, _MIPIA_TEARING_CTRL, _MIPIB_TEARING_CTRL)
+#define  TEARING_EFFECT_DELAY_SHIFT			0
+#define  TEARING_EFFECT_DELAY_MASK			(0xffff << 0)
+
+/* XXX */
+#define _MIPIA_AUTOPWG				(VLV_DISPLAY_BASE + 0x611a0)
+
+/* MIPI DSI Controller and D-PHY registers */
+
+#define _MIPIA_DEVICE_READY			(VLV_DISPLAY_BASE + 0xb000)
+#define _MIPIB_DEVICE_READY			(VLV_DISPLAY_BASE + 0xb800)
+#define MIPI_DEVICE_READY(pipe)		_PIPE(pipe, _MIPIA_DEVICE_READY, _MIPIB_DEVICE_READY)
+#define  BUS_POSSESSION					(1 << 3) /* set to give bus to receiver */
+#define  ULPS_STATE_MASK				(3 << 1)
+#define  ULPS_STATE_ENTER				(2 << 1) /* XXX */
+#define  ULPS_STATE_EXIT				(1 << 1) /* XXX */
+#define  DEVICE_READY					(1 << 0)
+
+#define _MIPIA_INTR_STAT			(VLV_DISPLAY_BASE + 0xb004)
+#define _MIPIB_INTR_STAT			(VLV_DISPLAY_BASE + 0xb804)
+#define MIPI_INTR_STAT(pipe)		_PIPE(pipe, _MIPIA_INTR_STAT, _MIPIB_INTR_STAT)
+#define _MIPIA_INTR_EN				(VLV_DISPLAY_BASE + 0xb008)
+#define _MIPIB_INTR_EN				(VLV_DISPLAY_BASE + 0xb808)
+#define MIPI_INTR_EN(pipe)		_PIPE(pipe, _MIPIA_INTR_EN, _MIPIB_INTR_EN)
+#define  TEARING_EFFECT					(1 << 31)
+#define  SPL_PKT_SENT_INTERRUPT				(1 << 30)
+#define  GEN_READ_DATA_AVAIL				(1 << 29)
+#define  LP_GENERIC_WR_FIFO_FULL			(1 << 28)
+#define  HS_GENERIC_WR_FIFO_FULL			(1 << 27)
+#define  RX_PROT_VIOLATION				(1 << 26)
+#define  RX_INVALID_TX_LENGTH				(1 << 25)
+#define  ACK_WITH_NO_ERROR				(1 << 24)
+#define  TURN_AROUND_ACK_TIMEOUT			(1 << 23)
+#define  LP_RX_TIMEOUT					(1 << 22)
+#define  HS_TX_TIMEOUT					(1 << 21)
+#define  DPI_FIFO_UNDERRUN				(1 << 20)
+#define  LOW_CONTENTION					(1 << 19)
+#define  HIGH_CONTENTION				(1 << 18)
+#define  TXDSI_VC_ID_INVALID				(1 << 17)
+#define  TXDSI_DATA_TYPE_NOT_RECOGNISED			(1 << 16)
+#define  TXCHECKSUM_ERROR				(1 << 15)
+#define  TXECC_MULTIBIT_ERROR				(1 << 14)
+#define  TXECC_SINGLE_BIT_ERROR				(1 << 13)
+#define  TXFALSE_CONTROL_ERROR				(1 << 12)
+#define  RXDSI_VC_ID_INVALID				(1 << 11)
+#define  RXDSI_DATA_TYPE_NOT_REGOGNISED			(1 << 10)
+#define  RXCHECKSUM_ERROR				(1 << 9)
+#define  RXECC_MULTIBIT_ERROR				(1 << 8)
+#define  RXECC_SINGLE_BIT_ERROR				(1 << 7)
+#define  RXFALSE_CONTROL_ERROR				(1 << 6)
+#define  RXHS_RECEIVE_TIMEOUT_ERROR			(1 << 5)
+#define  RX_LP_TX_SYNC_ERROR				(1 << 4)
+#define  RXEXCAPE_MODE_ENTRY_ERROR			(1 << 3)
+#define  RXEOT_SYNC_ERROR				(1 << 2)
+#define  RXSOT_SYNC_ERROR				(1 << 1)
+#define  RXSOT_ERROR					(1 << 0)
+
+#define _MIPIA_DSI_FUNC_PRG			(VLV_DISPLAY_BASE + 0xb00c)
+#define _MIPIB_DSI_FUNC_PRG			(VLV_DISPLAY_BASE + 0xb80c)
+#define MIPI_DSI_FUNC_PRG(pipe)		_PIPE(pipe, _MIPIA_DSI_FUNC_PRG, _MIPIB_DSI_FUNC_PRG)
+#define  CMD_MODE_DATA_WIDTH_MASK			(7 << 13)
+#define  CMD_MODE_NOT_SUPPORTED				(0 << 13)
+#define  CMD_MODE_DATA_WIDTH_16_BIT			(1 << 13)
+#define  CMD_MODE_DATA_WIDTH_9_BIT			(2 << 13)
+#define  CMD_MODE_DATA_WIDTH_8_BIT			(3 << 13)
+#define  CMD_MODE_DATA_WIDTH_OPTION1			(4 << 13)
+#define  CMD_MODE_DATA_WIDTH_OPTION2			(5 << 13)
+#define  VID_MODE_FORMAT_MASK				(0xf << 7)
+#define  VID_MODE_NOT_SUPPORTED				(0 << 7)
+#define  VID_MODE_FORMAT_RGB565				(1 << 7)
+#define  VID_MODE_FORMAT_RGB666				(2 << 7)
+#define  VID_MODE_FORMAT_RGB666_LOOSE			(3 << 7)
+#define  VID_MODE_FORMAT_RGB888				(4 << 7)
+#define  CMD_MODE_CHANNEL_NUMBER_SHIFT			5
+#define  CMD_MODE_CHANNEL_NUMBER_MASK			(3 << 5)
+#define  VID_MODE_CHANNEL_NUMBER_SHIFT			3
+#define  VID_MODE_CHANNEL_NUMBER_MASK			(3 << 3)
+#define  DATA_LANES_PRG_REG_SHIFT			0
+#define  DATA_LANES_PRG_REG_MASK			(7 << 0)
+
+#define _MIPIA_HS_TX_TIMEOUT			(VLV_DISPLAY_BASE + 0xb010)
+#define _MIPIB_HS_TX_TIMEOUT			(VLV_DISPLAY_BASE + 0xb810)
+#define MIPI_HS_TX_TIMEOUT(pipe)	_PIPE(pipe, _MIPIA_HS_TX_TIMEOUT, _MIPIB_HS_TX_TIMEOUT)
+#define  HIGH_SPEED_TX_TIMEOUT_COUNTER_MASK		0xffffff
+
+#define _MIPIA_LP_RX_TIMEOUT			(VLV_DISPLAY_BASE + 0xb014)
+#define _MIPIB_LP_RX_TIMEOUT			(VLV_DISPLAY_BASE + 0xb814)
+#define MIPI_LP_RX_TIMEOUT(pipe)	_PIPE(pipe, _MIPIA_LP_RX_TIMEOUT, _MIPIB_LP_RX_TIMEOUT)
+#define  LOW_POWER_RX_TIMEOUT_COUNTER_MASK		0xffffff
+
+#define _MIPIA_TURN_AROUND_TIMEOUT		(VLV_DISPLAY_BASE + 0xb018)
+#define _MIPIB_TURN_AROUND_TIMEOUT		(VLV_DISPLAY_BASE + 0xb818)
+#define MIPI_TURN_AROUND_TIMEOUT(pipe)	_PIPE(pipe, _MIPIA_TURN_AROUND_TIMEOUT, _MIPIB_TURN_AROUND_TIMEOUT)
+#define  TURN_AROUND_TIMEOUT_MASK			0x3f
+
+#define _MIPIA_DEVICE_RESET_TIMER		(VLV_DISPLAY_BASE + 0xb01c)
+#define _MIPIB_DEVICE_RESET_TIMER		(VLV_DISPLAY_BASE + 0xb81c)
+#define MIPI_DEVICE_RESET_TIMER(pipe)	_PIPE(pipe, _MIPIA_DEVICE_RESET_TIMER, _MIPIB_DEVICE_RESET_TIMER)
+#define  DEVICE_RESET_TIMER_MASK			0xffff
+
+#define _MIPIA_DPI_RESOLUTION			(VLV_DISPLAY_BASE + 0xb020)
+#define _MIPIB_DPI_RESOLUTION			(VLV_DISPLAY_BASE + 0xb820)
+#define MIPI_DPI_RESOLUTION(pipe)	_PIPE(pipe, _MIPIA_DPI_RESOLUTION, _MIPIB_DPI_RESOLUTION)
+#define  VERTICAL_ADDRESS_SHIFT				16
+#define  VERTICAL_ADDRESS_MASK				(0xffff << 16)
+#define  HORIZONTAL_ADDRESS_SHIFT			0
+#define  HORIZONTAL_ADDRESS_MASK			0xffff
+
+/* XXX */
+#define _MIPIA_DBI_FIFO_THROTTLE		(VLV_DISPLAY_BASE + 0xb024)
+#define _MIPIB_DBI_FIFO_THROTTLE		(VLV_DISPLAY_BASE + 0xb824)
+#define MIPI_DBI_FIFO_THROTTLE(pipe)	_PIPE(pipe, _MIPIA_DBI_FIFO_THROTTLE, _MIPIB_DBI_FIFO_THROTTLE)
+#define  DBI_FIFO_EMPTY_HALF				(0 << 0)
+#define  DBI_FIFO_EMPTY_QUARTER				(1 << 0)
+#define  DBI_FIFO_EMPTY_7_LOCATIONS			(2 << 0)
+
+/* regs below are bits 15:0 */
+#define _MIPIA_HSYNC_PADDING_COUNT		(VLV_DISPLAY_BASE + 0xb028)
+#define _MIPIB_HSYNC_PADDING_COUNT		(VLV_DISPLAY_BASE + 0xb828)
+#define MIPI_HSYNC_PADDING_COUNT(pipe)	_PIPE(pipe, _MIPIA_HSYNC_PADDING_COUNT, _MIPIB_HSYNC_PADDING_COUNT)
+
+#define _MIPIA_HBP_COUNT			(VLV_DISPLAY_BASE + 0xb02c)
+#define _MIPIB_HBP_COUNT			(VLV_DISPLAY_BASE + 0xb82c)
+#define MIPI_HBP_COUNT(pipe)		_PIPE(pipe, _MIPIA_HBP_COUNT, _MIPIB_HBP_COUNT)
+
+#define _MIPIA_HFP_COUNT			(VLV_DISPLAY_BASE + 0xb030)
+#define _MIPIB_HFP_COUNT			(VLV_DISPLAY_BASE + 0xb830)
+#define MIPI_HFP_COUNT(pipe)		_PIPE(pipe, _MIPIA_HFP_COUNT, _MIPIB_HFP_COUNT)
+
+#define _MIPIA_HACTIVE_AREA_COUNT		(VLV_DISPLAY_BASE + 0xb034)
+#define _MIPIB_HACTIVE_AREA_COUNT		(VLV_DISPLAY_BASE + 0xb834)
+#define MIPI_HACTIVE_AREA_COUNT(pipe)	_PIPE(pipe, _MIPIA_HACTIVE_AREA_COUNT, _MIPIB_HACTIVE_AREA_COUNT)
+
+#define _MIPIA_VSYNC_PADDING_COUNT		(VLV_DISPLAY_BASE + 0xb038)
+#define _MIPIB_VSYNC_PADDING_COUNT		(VLV_DISPLAY_BASE + 0xb838)
+#define MIPI_VSYNC_PADDING_COUNT(pipe)	_PIPE(pipe, _MIPIA_VSYNC_PADDING_COUNT, _MIPIB_VSYNC_PADDING_COUNT)
+
+#define _MIPIA_VBP_COUNT			(VLV_DISPLAY_BASE + 0xb03c)
+#define _MIPIB_VBP_COUNT			(VLV_DISPLAY_BASE + 0xb83c)
+#define MIPI_VBP_COUNT(pipe)		_PIPE(pipe, _MIPIA_VBP_COUNT, _MIPIB_VBP_COUNT)
+
+#define _MIPIA_VFP_COUNT			(VLV_DISPLAY_BASE + 0xb040)
+#define _MIPIB_VFP_COUNT			(VLV_DISPLAY_BASE + 0xb840)
+#define MIPI_VFP_COUNT(pipe)		_PIPE(pipe, _MIPIA_VFP_COUNT, _MIPIB_VFP_COUNT)
+
+#define _MIPIA_HIGH_LOW_SWITCH_COUNT		(VLV_DISPLAY_BASE + 0xb044)
+#define _MIPIB_HIGH_LOW_SWITCH_COUNT		(VLV_DISPLAY_BASE + 0xb844)
+#define MIPI_HIGH_LOW_SWITCH_COUNT(pipe)	_PIPE(pipe, _MIPIA_HIGH_LOW_SWITCH_COUNT, _MIPIB_HIGH_LOW_SWITCH_COUNT)
+/* regs above are bits 15:0 */
+
+#define _MIPIA_DPI_CONTROL			(VLV_DISPLAY_BASE + 0xb048)
+#define _MIPIB_DPI_CONTROL			(VLV_DISPLAY_BASE + 0xb848)
+#define MIPI_DPI_CONTROL(pipe)		_PIPE(pipe, _MIPIA_DPI_CONTROL, _MIPIB_DPI_CONTROL)
+#define  DPI_HS_MODE					(1 << 6)
+#define  BACKLIGHT_OFF					(1 << 5)
+#define  BACKLIGHT_ON					(1 << 4)
+#define  COLOR_MODE_OFF					(1 << 3)
+#define  COLOR_MODE_ON					(1 << 2)
+#define  TURN_ON					(1 << 1)
+#define  SHUTDOWN					(1 << 0)
+
+#define _MIPIA_DPI_DATA				(VLV_DISPLAY_BASE + 0xb04c)
+#define _MIPIB_DPI_DATA				(VLV_DISPLAY_BASE + 0xb84c)
+#define MIPI_DPI_DATA(pipe)		_PIPE(pipe, _MIPIA_DPI_DATA, _MIPIB_DPI_DATA)
+#define  COMMAND_BYTE_SHIFT				0
+#define  COMMAND_BYTE_MASK				(0x3f << 0)
+
+#define _MIPIA_INIT_COUNT			(VLV_DISPLAY_BASE + 0xb050)
+#define _MIPIB_INIT_COUNT			(VLV_DISPLAY_BASE + 0xb850)
+#define MIPI_INIT_COUNT(pipe)		_PIPE(pipe, _MIPIA_INIT_COUNT, _MIPIB_INIT_COUNT)
+#define  MASTER_INIT_TIMER_SHIFT			0
+#define  MASTER_INIT_TIMER_MASK				(0xffff << 0)
+
+#define _MIPIA_MAX_RETURN_PKT_SIZE		(VLV_DISPLAY_BASE + 0xb054)
+#define _MIPIB_MAX_RETURN_PKT_SIZE		(VLV_DISPLAY_BASE + 0xb854)
+#define MIPI_MAX_RETURN_PKT_SIZE(pipe)	_PIPE(pipe, _MIPIA_MAX_RETURN_PKT_SIZE, _MIPIB_MAX_RETURN_PKT_SIZE)
+#define  MAX_RETURN_PKT_SIZE_SHIFT			0
+#define  MAX_RETURN_PKT_SIZE_MASK			(0x3ff << 0)
+
+#define _MIPIA_VIDEO_MODE_FORMAT		(VLV_DISPLAY_BASE + 0xb058)
+#define _MIPIB_VIDEO_MODE_FORMAT		(VLV_DISPLAY_BASE + 0xb858)
+#define MIPI_VIDEO_MODE_FORMAT(pipe)	_PIPE(pipe, _MIPIA_VIDEO_MODE_FORMAT, _MIPIB_VIDEO_MODE_FORMAT)
+#define  RANDOM_DPI_DISPLAY_RESOLUTION			(1 << 4)
+#define  DISABLE_VIDEO_BTA				(1 << 3)
+#define  IP_TG_CONFIG					(1 << 2)
+#define  VIDEO_MODE_NON_BURST_WITH_SYNC_PULSE		(1 << 0)
+#define  VIDEO_MODE_NON_BURST_WITH_SYNC_EVENTS		(2 << 0)
+#define  VIDEO_MODE_BURST				(3 << 0)
+
+#define _MIPIA_EOT_DISABLE			(VLV_DISPLAY_BASE + 0xb05c)
+#define _MIPIB_EOT_DISABLE			(VLV_DISPLAY_BASE + 0xb85c)
+#define MIPI_EOT_DISABLE(pipe)		_PIPE(pipe, _MIPIA_EOT_DISABLE, _MIPIB_EOT_DISABLE)
+#define  LP_RX_TIMEOUT_ERROR_RECOVERY_DISABLE		(1 << 7)
+#define  HS_RX_TIMEOUT_ERROR_RECOVERY_DISABLE		(1 << 6)
+#define  LOW_CONTENTION_RECOVERY_DISABLE		(1 << 5)
+#define  HIGH_CONTENTION_RECOVERY_DISABLE		(1 << 4)
+#define  TXDSI_TYPE_NOT_RECOGNISED_ERROR_RECOVERY_DISABLE (1 << 3)
+#define  TXECC_MULTIBIT_ERROR_RECOVERY_DISABLE		(1 << 2)
+#define  CLOCKSTOP					(1 << 1)
+#define  EOT_DISABLE					(1 << 0)
+
+#define _MIPIA_LP_BYTECLK			(VLV_DISPLAY_BASE + 0xb060)
+#define _MIPIB_LP_BYTECLK			(VLV_DISPLAY_BASE + 0xb860)
+#define MIPI_LP_BYTECLK(pipe)		_PIPE(pipe, _MIPIA_LP_BYTECLK, _MIPIB_LP_BYTECLK)
+#define  LP_BYTECLK_SHIFT				0
+#define  LP_BYTECLK_MASK				(0xffff << 0)
+
+/* bits 31:0 */
+#define _MIPIA_LP_GEN_DATA			(VLV_DISPLAY_BASE + 0xb064)
+#define _MIPIB_LP_GEN_DATA			(VLV_DISPLAY_BASE + 0xb864)
+#define MIPI_LP_GEN_DATA(pipe)		_PIPE(pipe, _MIPIA_LP_GEN_DATA, _MIPIB_LP_GEN_DATA)
+
+/* bits 31:0 */
+#define _MIPIA_HS_GEN_DATA			(VLV_DISPLAY_BASE + 0xb068)
+#define _MIPIB_HS_GEN_DATA			(VLV_DISPLAY_BASE + 0xb868)
+#define MIPI_HS_GEN_DATA(pipe)		_PIPE(pipe, _MIPIA_HS_GEN_DATA, _MIPIB_HS_GEN_DATA)
+
+#define _MIPIA_LP_GEN_CTRL			(VLV_DISPLAY_BASE + 0xb06c)
+#define _MIPIB_LP_GEN_CTRL			(VLV_DISPLAY_BASE + 0xb86c)
+#define MIPI_LP_GEN_CTRL(pipe)		_PIPE(pipe, _MIPIA_LP_GEN_CTRL, _MIPIB_LP_GEN_CTRL)
+#define _MIPIA_HS_GEN_CTRL			(VLV_DISPLAY_BASE + 0xb070)
+#define _MIPIB_HS_GEN_CTRL			(VLV_DISPLAY_BASE + 0xb870)
+#define MIPI_HS_GEN_CTRL(pipe)		_PIPE(pipe, _MIPIA_HS_GEN_CTRL, _MIPIB_HS_GEN_CTRL)
+#define  LONG_PACKET_WORD_COUNT_SHIFT			8
+#define  LONG_PACKET_WORD_COUNT_MASK			(0xffff << 8)
+#define  SHORT_PACKET_PARAM_SHIFT			8
+#define  SHORT_PACKET_PARAM_MASK			(0xffff << 8)
+#define  VIRTUAL_CHANNEL_SHIFT				6
+#define  VIRTUAL_CHANNEL_MASK				(3 << 6)
+#define  DATA_TYPE_SHIFT				0
+#define  DATA_TYPE_MASK					(3f << 0)
+/* data type values, see include/video/mipi_display.h */
+
+#define _MIPIA_GEN_FIFO_STAT			(VLV_DISPLAY_BASE + 0xb074)
+#define _MIPIB_GEN_FIFO_STAT			(VLV_DISPLAY_BASE + 0xb874)
+#define MIPI_GEN_FIFO_STAT(pipe)	_PIPE(pipe, _MIPIA_GEN_FIFO_STAT, _MIPIB_GEN_FIFO_STAT)
+#define  DPI_FIFO_EMPTY					(1 << 28)
+#define  DBI_FIFO_EMPTY					(1 << 27)
+#define  LP_CTRL_FIFO_EMPTY				(1 << 26)
+#define  LP_CTRL_FIFO_HALF_EMPTY			(1 << 25)
+#define  LP_CTRL_FIFO_FULL				(1 << 24)
+#define  HS_CTRL_FIFO_EMPTY				(1 << 18)
+#define  HS_CTRL_FIFO_HALF_EMPTY			(1 << 17)
+#define  HS_CTRL_FIFO_FULL				(1 << 16)
+#define  LP_DATA_FIFO_EMPTY				(1 << 10)
+#define  LP_DATA_FIFO_HALF_EMPTY			(1 << 9)
+#define  LP_DATA_FIFO_FULL				(1 << 8)
+#define  HS_DATA_FIFO_EMPTY				(1 << 2)
+#define  HS_DATA_FIFO_HALF_EMPTY			(1 << 1)
+#define  HS_DATA_FIFO_FULL				(1 << 0)
+
+#define _MIPIA_HS_LS_DBI_ENABLE			(VLV_DISPLAY_BASE + 0xb078)
+#define _MIPIB_HS_LS_DBI_ENABLE			(VLV_DISPLAY_BASE + 0xb878)
+#define MIPI_HS_LP_DBI_ENABLE(pipe)	_PIPE(pipe, _MIPIA_HS_LS_DBI_ENABLE, _MIPIB_HS_LS_DBI_ENABLE)
+#define  DBI_HS_LP_MODE_MASK				(1 << 0)
+#define  DBI_LP_MODE					(1 << 0)
+#define  DBI_HS_MODE					(0 << 0)
+
+#define _MIPIA_DPHY_PARAM			(VLV_DISPLAY_BASE + 0xb080)
+#define _MIPIB_DPHY_PARAM			(VLV_DISPLAY_BASE + 0xb880)
+#define MIPI_DPHY_PARAM(pipe)		_PIPE(pipe, _MIPIA_DPHY_PARAM, _MIPIB_DPHY_PARAM)
+#define  EXIT_ZERO_COUNT_SHIFT				24
+#define  EXIT_ZERO_COUNT_MASK				(0x3f << 24)
+#define  TRAIL_COUNT_SHIFT				16
+#define  TRAIL_COUNT_MASK				(0x1f << 16)
+#define  CLK_ZERO_COUNT_SHIFT				8
+#define  CLK_ZERO_COUNT_MASK				(0xff << 8)
+#define  PREPARE_COUNT_SHIFT				0
+#define  PREPARE_COUNT_MASK				(0x3f << 0)
+
+/* bits 31:0 */
+#define _MIPIA_DBI_BW_CTRL			(VLV_DISPLAY_BASE + 0xb084)
+#define _MIPIB_DBI_BW_CTRL			(VLV_DISPLAY_BASE + 0xb884)
+#define MIPI_DBI_BW_CTRL(pipe)		_PIPE(pipe, _MIPIA_DBI_BW_CTRL, _MIPIB_DBI_BW_CTRL)
+
+#define _MIPIA_CLK_LANE_SWITCH_TIME_CNT		(VLV_DISPLAY_BASE + 0xb088)
+#define _MIPIB_CLK_LANE_SWITCH_TIME_CNT		(VLV_DISPLAY_BASE + 0xb888)
+#define MIPI_CLK_LANE_SWITCH_TIME_CNT(pipe)	_PIPE(pipe, _MIPIA_CLK_LANE_SWITCH_TIME_CNT, _MIPIB_CLK_LANE_SWITCH_TIME_CNT)
+#define  LP_HS_SSW_CNT_SHIFT				16
+#define  LP_HS_SSW_CNT_MASK				(0xffff << 16)
+#define  HS_LP_PWR_SW_CNT_SHIFT				0
+#define  HS_LP_PWR_SW_CNT_MASK				(0xffff << 0)
+
+#define _MIPIA_STOP_STATE_STALL			(VLV_DISPLAY_BASE + 0xb08c)
+#define _MIPIB_STOP_STATE_STALL			(VLV_DISPLAY_BASE + 0xb88c)
+#define MIPI_STOP_STATE_STALL(pipe)	_PIPE(pipe, _MIPIA_STOP_STATE_STALL, _MIPIB_STOP_STATE_STALL)
+#define  STOP_STATE_STALL_COUNTER_SHIFT			0
+#define  STOP_STATE_STALL_COUNTER_MASK			(0xff << 0)
+
+#define _MIPIA_INTR_STAT_REG_1			(VLV_DISPLAY_BASE + 0xb090)
+#define _MIPIB_INTR_STAT_REG_1			(VLV_DISPLAY_BASE + 0xb890)
+#define MIPI_INTR_STAT_REG_1(pipe)	_PIPE(pipe, _MIPIA_INTR_STAT_REG_1, _MIPIB_INTR_STAT_REG_1)
+#define _MIPIA_INTR_EN_REG_1			(VLV_DISPLAY_BASE + 0xb094)
+#define _MIPIB_INTR_EN_REG_1			(VLV_DISPLAY_BASE + 0xb894)
+#define MIPI_INTR_EN_REG_1(pipe)	_PIPE(pipe, _MIPIA_INTR_EN_REG_1, _MIPIB_INTR_EN_REG_1)
+#define  RX_CONTENTION_DETECTED				(1 << 0)
+
+/* XXX: only pipe A ?!? */
+#define MIPIA_DBI_TYPEC_CTRL			(VLV_DISPLAY_BASE + 0xb100)
+#define  DBI_TYPEC_ENABLE				(1 << 31)
+#define  DBI_TYPEC_WIP					(1 << 30)
+#define  DBI_TYPEC_OPTION_SHIFT				28
+#define  DBI_TYPEC_OPTION_MASK				(3 << 28)
+#define  DBI_TYPEC_FREQ_SHIFT				24
+#define  DBI_TYPEC_FREQ_MASK				(0xf << 24)
+#define  DBI_TYPEC_OVERRIDE				(1 << 8)
+#define  DBI_TYPEC_OVERRIDE_COUNTER_SHIFT		0
+#define  DBI_TYPEC_OVERRIDE_COUNTER_MASK		(0xff << 0)
+
+
+/* MIPI adapter registers */
+
+#define _MIPIA_CTRL				(VLV_DISPLAY_BASE + 0xb104)
+#define _MIPIB_CTRL				(VLV_DISPLAY_BASE + 0xb904)
+#define MIPI_CTRL(pipe)			_PIPE(pipe, _MIPIA_CTRL, _MIPIB_CTRL)
+#define  ESCAPE_CLOCK_DIVIDER_SHIFT			5 /* A only */
+#define  ESCAPE_CLOCK_DIVIDER_MASK			(3 << 5)
+#define  ESCAPE_CLOCK_DIVIDER_1				(0 << 5)
+#define  ESCAPE_CLOCK_DIVIDER_2				(1 << 5)
+#define  ESCAPE_CLOCK_DIVIDER_4				(2 << 5)
+#define  READ_REQUEST_PRIORITY_SHIFT			3
+#define  READ_REQUEST_PRIORITY_MASK			(3 << 3)
+#define  READ_REQUEST_PRIORITY_LOW			(0 << 3)
+#define  READ_REQUEST_PRIORITY_HIGH			(3 << 3)
+#define  RGB_FLIP_TO_BGR				(1 << 2)
+
+#define _MIPIA_DATA_ADDRESS			(VLV_DISPLAY_BASE + 0xb108)
+#define _MIPIB_DATA_ADDRESS			(VLV_DISPLAY_BASE + 0xb908)
+#define MIPI_DATA_ADDRESS(pipe)		_PIPE(pipe, _MIPIA_DATA_ADDRESS, _MIPIB_DATA_ADDRESS)
+#define  DATA_MEM_ADDRESS_SHIFT				5
+#define  DATA_MEM_ADDRESS_MASK				(0x7ffffff << 5)
+#define  DATA_VALID					(1 << 0)
+
+#define _MIPIA_DATA_LENGTH			(VLV_DISPLAY_BASE + 0xb10c)
+#define _MIPIB_DATA_LENGTH			(VLV_DISPLAY_BASE + 0xb90c)
+#define MIPI_DATA_LENGTH(pipe)		_PIPE(pipe, _MIPIA_DATA_LENGTH, _MIPIB_DATA_LENGTH)
+#define  DATA_LENGTH_SHIFT				0
+#define  DATA_LENGTH_MASK				(0xfffff << 0)
+
+#define _MIPIA_COMMAND_ADDRESS			(VLV_DISPLAY_BASE + 0xb110)
+#define _MIPIB_COMMAND_ADDRESS			(VLV_DISPLAY_BASE + 0xb910)
+#define MIPI_COMMAND_ADDRESS(pipe)	_PIPE(pipe, _MIPIA_COMMAND_ADDRESS, _MIPIB_COMMAND_ADDRESS)
+#define  COMMAND_MEM_ADDRESS_SHIFT			5
+#define  COMMAND_MEM_ADDRESS_MASK			(0x7ffffff << 5)
+#define  AUTO_PWG_ENABLE				(1 << 2)
+#define  MEMORY_WRITE_DATA_FROM_PIPE_RENDERING		(1 << 1)
+#define  COMMAND_VALID					(1 << 0)
+
+#define _MIPIA_COMMAND_LENGTH			(VLV_DISPLAY_BASE + 0xb114)
+#define _MIPIB_COMMAND_LENGTH			(VLV_DISPLAY_BASE + 0xb914)
+#define MIPI_COMMAND_LENGTH(pipe)	_PIPE(pipe, _MIPIA_COMMAND_LENGTH, _MIPIB_COMMAND_LENGTH)
+#define  COMMAND_LENGTH_SHIFT(n)			(8 * (n)) /* n: 0...3 */
+#define  COMMAND_LENGTH_MASK(n)				(0xff << (8 * (n)))
+
+#define _MIPIA_READ_DATA_RETURN0		(VLV_DISPLAY_BASE + 0xb118)
+#define _MIPIB_READ_DATA_RETURN0		(VLV_DISPLAY_BASE + 0xb918)
+#define MIPI_READ_DATA_RETURN(pipe, n) \
+	(_PIPE(pipe, _MIPIA_READ_DATA_RETURN0, _MIPIB_READ_DATA_RETURN0) + 4 * (n)) /* n: 0...7 */
+
+#define _MIPIA_READ_DATA_VALID			(VLV_DISPLAY_BASE + 0xb138)
+#define _MIPIB_READ_DATA_VALID			(VLV_DISPLAY_BASE + 0xb938)
+#define MIPI_READ_DATA_VALID(pipe)	_PIPE(pipe, _MIPIA_READ_DATA_VALID, _MIPIB_READ_DATA_VALID)
+#define  READ_DATA_VALID(n)				(1 << (n))
+
 #endif /* _I915_REG_H_ */

Signature · 1 line

1.7.9.5

Jani Nikula

author

2013-08-13 13:28 UTC #9 lore raw

PATCH 5/14 drm/i915: add MIPI DSI output type and subtypes

In reply to Jani Nikula

Signed-off-by Jani Nikula <[email protected]>

Signed-off-by Shobhit Kumar <[email protected]>

---
 drivers/gpu/drm/i915/intel_drv.h |    6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

drivers/gpu/drm/i915/intel_drv.h +5 -1

index 01455aa..a31abc6 100644
@@ -93,13 +93,17 @@
 #define INTEL_OUTPUT_HDMI 6
 #define INTEL_OUTPUT_DISPLAYPORT 7
 #define INTEL_OUTPUT_EDP 8
-#define INTEL_OUTPUT_UNKNOWN 9
+#define INTEL_OUTPUT_DSI 9
+#define INTEL_OUTPUT_UNKNOWN 10
 
 #define INTEL_DVO_CHIP_NONE 0
 #define INTEL_DVO_CHIP_LVDS 1
 #define INTEL_DVO_CHIP_TMDS 2
 #define INTEL_DVO_CHIP_TVOUT 4
 
+#define INTEL_DSI_COMMAND_MODE	0
+#define INTEL_DSI_VIDEO_MODE	1
+
 struct intel_framebuffer {
 	struct drm_framebuffer base;
 	struct drm_i915_gem_object *obj;

Signature · 1 line

1.7.9.5

Jani Nikula

author

2013-08-13 13:28 UTC #10 lore raw

PATCH 6/14 drm/i915: add structs for MIPI DSI output

In reply to Jani Nikula

The sub-encoder model is copied from DVO.

Signed-off-by Jani Nikula <[email protected]>

---
 drivers/gpu/drm/i915/intel_dsi.h |   99 ++++++++++++++++++++++++++++++++++++++
 1 file changed, 99 insertions(+)
 create mode 100644 drivers/gpu/drm/i915/intel_dsi.h

drivers/gpu/drm/i915/intel_dsi.h new file +99 -0

new file mode 100644
index 0000000..45f649a
@@ -0,0 +1,99 @@
+/*
+ * Copyright © 2013 Intel Corporation
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice (including the next
+ * paragraph) shall be included in all copies or substantial portions of the
+ * Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
+ * DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef _INTEL_DSI_H
+#define _INTEL_DSI_H
+
+#include <drm/drmP.h>
+#include <drm/drm_crtc.h>
+#include "intel_drv.h"
+
+struct intel_dsi_device {
+	unsigned int panel_id;
+	const char *name;
+	int type;
+	const struct intel_dsi_dev_ops *dev_ops;
+	void *dev_priv;
+};
+
+struct intel_dsi_dev_ops {
+	bool (*init)(struct intel_dsi_device *dsi);
+
+	/* This callback must be able to assume DSI commands can be sent */
+	void (*enable)(struct intel_dsi_device *dsi);
+
+	/* This callback must be able to assume DSI commands can be sent */
+	void (*disable)(struct intel_dsi_device *dsi);
+
+	int (*mode_valid)(struct intel_dsi_device *dsi,
+			  struct drm_display_mode *mode);
+
+	bool (*mode_fixup)(struct intel_dsi_device *dsi,
+			   const struct drm_display_mode *mode,
+			   struct drm_display_mode *adjusted_mode);
+
+	void (*mode_set)(struct intel_dsi_device *dsi,
+			 struct drm_display_mode *mode,
+			 struct drm_display_mode *adjusted_mode);
+
+	enum drm_connector_status (*detect)(struct intel_dsi_device *dsi);
+
+	bool (*get_hw_state)(struct intel_dsi_device *dev);
+
+	struct drm_display_mode *(*get_modes)(struct intel_dsi_device *dsi);
+
+	void (*destroy) (struct intel_dsi_device *dsi);
+};
+
+struct intel_dsi {
+	struct intel_encoder base;
+
+	struct intel_dsi_device dev;
+
+	struct drm_display_mode *panel_fixed_mode;
+
+	/* if true, use HS mode, otherwise LP */
+	bool hs;
+
+	/* virtual channel */
+	int channel;
+
+	/* number of DSI lanes */
+	unsigned int lane_count;
+
+	/* video mode pixel format for MIPI_DSI_FUNC_PRG register */
+	u32 pixel_format;
+
+	/* video mode format for MIPI_VIDEO_MODE_FORMAT register */
+	u32 video_mode_format;
+
+	/* eot for MIPI_EOT_DISABLE register */
+	u32 eot_disable;
+};
+
+static inline struct intel_dsi *enc_to_intel_dsi(struct drm_encoder *encoder)
+{
+	return container_of(encoder, struct intel_dsi, base.base);
+}
+
+#endif /* _INTEL_DSI_H */

Signature · 6 lines

1.7.9.5

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

Jani Nikula

author

2013-08-13 13:28 UTC #11 lore raw

PATCH 7/14 drm/i915: add MIPI DSI command sending routines

In reply to Jani Nikula

Signed-off-by Jani Nikula <[email protected]>

---
 drivers/gpu/drm/i915/Makefile        |    1 +
 drivers/gpu/drm/i915/intel_dsi_cmd.c |  442 ++++++++++++++++++++++++++++++++++
 drivers/gpu/drm/i915/intel_dsi_cmd.h |  109 +++++++++
 3 files changed, 552 insertions(+)
 create mode 100644 drivers/gpu/drm/i915/intel_dsi_cmd.c
 create mode 100644 drivers/gpu/drm/i915/intel_dsi_cmd.h

drivers/gpu/drm/i915/Makefile +1 -0

index b8449a8..8bffd29 100644
@@ -21,6 +21,7 @@ i915-y := i915_drv.o i915_dma.o i915_irq.o \
 	  intel_display.o \
 	  intel_crt.o \
 	  intel_lvds.o \
+	  intel_dsi_cmd.o \
 	  intel_bios.o \
 	  intel_ddi.o \
 	  intel_dp.o \

drivers/gpu/drm/i915/intel_dsi_cmd.c new file +442 -0

442 lines not on this page · raw message

drivers/gpu/drm/i915/intel_dsi_cmd.h new file +109 -0

109 lines not on this page · raw message

Signature · 6 lines

1.7.9.5

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

Jani Nikula

author

2013-08-13 13:28 UTC #12 lore raw

PATCH 8/14 drm/i915: add basic MIPI DSI output support

In reply to Jani Nikula

This does not include any panel specific sub-encoders yet.

Signed-off-by Jani Nikula <[email protected]>

Signed-off-by Shobhit Kumar <[email protected]>

---
 drivers/gpu/drm/i915/Makefile    |    1 +
 drivers/gpu/drm/i915/intel_drv.h |    1 +
 drivers/gpu/drm/i915/intel_dsi.c |  548 ++++++++++++++++++++++++++++++++++++++
 3 files changed, 550 insertions(+)
 create mode 100644 drivers/gpu/drm/i915/intel_dsi.c

drivers/gpu/drm/i915/Makefile +1 -0

index 8bffd29..5864c5b 100644
@@ -21,6 +21,7 @@ i915-y := i915_drv.o i915_dma.o i915_irq.o \
 	  intel_display.o \
 	  intel_crt.o \
 	  intel_lvds.o \
+	  intel_dsi.o \
 	  intel_dsi_cmd.o \
 	  intel_bios.o \
 	  intel_ddi.o \

drivers/gpu/drm/i915/intel_drv.h +1 -0

index a31abc6..cbe3df1 100644
@@ -525,6 +525,7 @@ extern void intel_mark_fb_busy(struct drm_i915_gem_object *obj,
 			       struct intel_ring_buffer *ring);
 extern void intel_mark_idle(struct drm_device *dev);
 extern void intel_lvds_init(struct drm_device *dev);
+extern bool intel_dsi_init(struct drm_device *dev);
 extern bool intel_is_dual_link_lvds(struct drm_device *dev);
 extern void intel_dp_init(struct drm_device *dev, int output_reg,
 			  enum port port);

drivers/gpu/drm/i915/intel_dsi.c new file +548 -0

548 lines not on this page · raw message

Signature · 6 lines

1.7.9.5

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

Jani Nikula

author

2013-08-13 13:28 UTC #14 lore raw

PATCH 9/14 drm/i915: add VLV DSI PLL Calculations

In reply to Jani Nikula

From: ymohanma <[email protected]>

Signed-off-by ymohanma <[email protected]>

Signed-off-by Shobhit Kumar <[email protected]>

Signed-off-by Jani Nikula <[email protected]>

---
 drivers/gpu/drm/i915/Makefile        |    1 +
 drivers/gpu/drm/i915/i915_reg.h      |   10 ++
 drivers/gpu/drm/i915/intel_display.c |    2 +
 drivers/gpu/drm/i915/intel_dsi.c     |    5 +
 drivers/gpu/drm/i915/intel_dsi.h     |    2 +
 drivers/gpu/drm/i915/intel_dsi_pll.c |  290 ++++++++++++++++++++++++++++++++++
 6 files changed, 310 insertions(+)
 create mode 100644 drivers/gpu/drm/i915/intel_dsi_pll.c

drivers/gpu/drm/i915/Makefile +1 -0

index 5864c5b..65e60d2 100644
@@ -23,6 +23,7 @@ i915-y := i915_drv.o i915_dma.o i915_irq.o \
 	  intel_lvds.o \
 	  intel_dsi.o \
 	  intel_dsi_cmd.o \
+	  intel_dsi_pll.o \
 	  intel_bios.o \
 	  intel_ddi.o \
 	  intel_dp.o \

drivers/gpu/drm/i915/i915_reg.h +10 -0

index 32e32b6..5713540 100644
@@ -390,6 +390,16 @@
 #define   FB_FMAX_VMIN_FREQ_LO_SHIFT		27
 #define   FB_FMAX_VMIN_FREQ_LO_MASK		0xf8000000
 
+/* vlv2 north clock has */
+#define CCK_REG_DSI_PLL_FUSE			0x44
+#define CCK_REG_DSI_PLL_CONTROL			0x48
+#define  DSI_PLL_VCO_EN				(1 << 31)
+#define  DSI_PLL_LDO_GATE			(1 << 30)
+#define  DSI_PLL_P1_POST_DIV_SHIFT		17
+#define  DSI_PLL_P1_POST_DIV_MASK		(0x1ff << 17)
+#define  DSI_PLL_LOCK				(1 << 0)
+#define CCK_REG_DSI_PLL_DIVIDER			0x4c
+
 /*
  * DPIO - a special bus for various display related registers to hide behind
  *

drivers/gpu/drm/i915/intel_display.c +2 -0

index cec9189..78c42a1 100644
@@ -1683,6 +1683,7 @@ static void intel_enable_pipe(struct drm_i915_private *dev_priv, enum pipe pipe,
 	 * need the check.
 	 */
 	if (!HAS_PCH_SPLIT(dev_priv->dev))
+		/* XXX: Fix for DSI PLL */
 		assert_pll_enabled(dev_priv, pipe);
 	else {
 		if (pch_port) {

@@ -6495,6 +6496,7 @@ void intel_crtc_load_lut(struct drm_crtc *crtc)
 		return;
 
 	if (!HAS_PCH_SPLIT(dev_priv->dev))
+		/* XXX: Fix for DSI PLL */
 		assert_pll_enabled(dev_priv, pipe);
 
 	/* use legacy palette for Ironlake */

drivers/gpu/drm/i915/intel_dsi.c +5 -0

index aa81dd8..1dc5a77 100644
@@ -68,6 +68,8 @@ static bool intel_dsi_compute_config(struct intel_encoder *encoder,
 static void intel_dsi_pre_pll_enable(struct intel_encoder *encoder)
 {
 	DRM_DEBUG_KMS("\n");
+
+	vlv_enable_dsi_pll(encoder);
 }
 
 static void intel_dsi_pre_enable(struct intel_encoder *encoder)

@@ -294,6 +296,9 @@ static void intel_dsi_mode_set(struct intel_encoder *intel_encoder)
 
 	DRM_DEBUG_KMS("pipe %d\n", pipe);
 
+	/* Update the DSI PLL */
+	vlv_enable_dsi_pll(intel_encoder);
+
 	/* escape clock divider, 20MHz, shared for A and C. device ready must be
 	 * off when doing this! txclkesc? */
 	tmp = I915_READ(MIPI_CTRL(0));

drivers/gpu/drm/i915/intel_dsi.h +2 -0

index 45f649a..0e0a212 100644
@@ -96,4 +96,6 @@ static inline struct intel_dsi *enc_to_intel_dsi(struct drm_encoder *encoder)
 	return container_of(encoder, struct intel_dsi, base.base);
 }
 
+extern void vlv_enable_dsi_pll(struct intel_encoder *encoder);
+
 #endif /* _INTEL_DSI_H */

drivers/gpu/drm/i915/intel_dsi_pll.c new file +290 -0

290 lines not on this page · raw message

Signature · 6 lines

1.7.9.5

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

Jani Nikula

author

2013-08-13 13:28 UTC #15 lore raw

PATCH 10/14 drm/i915: don't enable DPLL for DSI

In reply to Jani Nikula

DPLL is not needed for DSI

Signed-off-by Jani Nikula <[email protected]>

Signed-off-by Shobhit Kumar <[email protected]>

---
 drivers/gpu/drm/i915/intel_display.c |   48 ++++++++++++++++++++--------------
 1 file changed, 29 insertions(+), 19 deletions(-)

drivers/gpu/drm/i915/intel_display.c +29 ~~-19~~

index 78c42a1..e3ca335 100644
@@ -3660,7 +3660,8 @@ static void valleyview_crtc_enable(struct drm_crtc *crtc)
 		if (encoder->pre_pll_enable)
 			encoder->pre_pll_enable(encoder);
 
-	vlv_enable_pll(intel_crtc);
+	if (!intel_pipe_has_type(crtc, INTEL_OUTPUT_DSI))
+		vlv_enable_pll(intel_crtc);
 
 	for_each_encoder_on_crtc(dev, crtc, encoder)
 		if (encoder->pre_enable)

@@ -3775,7 +3776,8 @@ static void i9xx_crtc_disable(struct drm_crtc *crtc)
 		if (encoder->post_disable)
 			encoder->post_disable(encoder);
 
-	i9xx_disable_pll(dev_priv, pipe);
+	if (!intel_pipe_has_type(crtc, INTEL_OUTPUT_DSI))
+		i9xx_disable_pll(dev_priv, pipe);
 
 	intel_crtc->active = false;
 	intel_update_fbc(dev);

@@ -4843,7 +4845,7 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 	intel_clock_t clock, reduced_clock;
 	u32 dspcntr;
 	bool ok, has_reduced_clock = false;
-	bool is_lvds = false;
+	bool is_lvds = false, is_dsi = false;
 	struct intel_encoder *encoder;
 	const intel_limit_t *limit;
 	int ret;

@@ -4853,6 +4855,9 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 		case INTEL_OUTPUT_LVDS:
 			is_lvds = true;
 			break;
+		case INTEL_OUTPUT_DSI:
+			is_dsi = true;
+			break;
 		}
 
 		num_connectors++;

@@ -4860,18 +4865,21 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 
 	refclk = i9xx_get_refclk(crtc, num_connectors);
 
-	/*
-	 * Returns a set of divisors for the desired target clock with the given
-	 * refclk, or FALSE.  The returned values represent the clock equation:
-	 * reflck * (5 * (m1 + 2) + (m2 + 2)) / (n + 2) / p1 / p2.
-	 */
-	limit = intel_limit(crtc, refclk);
-	ok = dev_priv->display.find_dpll(limit, crtc,
-					 intel_crtc->config.port_clock,
-					 refclk, NULL, &clock);
-	if (!ok && !intel_crtc->config.clock_set) {
-		DRM_ERROR("Couldn't find PLL settings for mode!\n");
-		return -EINVAL;
+	if (!is_dsi) {
+		/*
+		 * Returns a set of divisors for the desired target clock with
+		 * the given refclk, or FALSE.  The returned values represent
+		 * the clock equation: reflck * (5 * (m1 + 2) + (m2 + 2)) / (n +
+		 * 2) / p1 / p2.
+		 */
+		limit = intel_limit(crtc, refclk);
+		ok = dev_priv->display.find_dpll(limit, crtc,
+						 intel_crtc->config.port_clock,
+						 refclk, NULL, &clock);
+		if (!ok && !intel_crtc->config.clock_set) {
+			DRM_ERROR("Couldn't find PLL settings for mode!\n");
+			return -EINVAL;
+		}
 	}
 
 	/* Ensure that the cursor is valid for the new mode before changing... */

@@ -4899,16 +4907,18 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 		intel_crtc->config.dpll.p2 = clock.p2;
 	}
 
-	if (IS_GEN2(dev))
+	if (IS_GEN2(dev)) {
 		i8xx_update_pll(intel_crtc,
 				has_reduced_clock ? &reduced_clock : NULL,
 				num_connectors);
-	else if (IS_VALLEYVIEW(dev))
-		vlv_update_pll(intel_crtc);
-	else
+	} else if (IS_VALLEYVIEW(dev)) {
+		if (!is_dsi)
+			vlv_update_pll(intel_crtc);
+	} else {
 		i9xx_update_pll(intel_crtc,
 				has_reduced_clock ? &reduced_clock : NULL,
                                 num_connectors);
+	}
 
 	/* Set up the display plane register */
 	dspcntr = DISPPLANE_GAMMA_ENABLE;

Signature · 1 line

1.7.9.5

Jani Nikula

author

2013-08-13 13:28 UTC #16 lore raw

PATCH 11/14 drm/i915: Band Gap WA

In reply to Jani Nikula

From: Shobhit Kumar <[email protected]>

Signed-off-by Shobhit Kumar <[email protected]>

Signed-off-by ymohanma <[email protected]>

Signed-off-by Jani Nikula <[email protected]>

---
 drivers/gpu/drm/i915/intel_dsi.c |   48 ++++++++++++++++++++++++++++++++++++++
 1 file changed, 48 insertions(+)

drivers/gpu/drm/i915/intel_dsi.c +48 -0

index 1dc5a77..d28be01 100644
@@ -37,6 +37,51 @@
 static const struct intel_dsi_device intel_dsi_devices[] = {
 };
 
+
+static void vlv_cck_modify(struct drm_i915_private *dev_priv, u32 reg, u32 val,
+			   u32 mask)
+{
+	u32 tmp = vlv_cck_read(dev_priv, reg);
+	tmp &= ~mask;
+	tmp |= val;
+	vlv_cck_write(dev_priv, reg, tmp);
+}
+
+static void band_gap_wa(struct drm_i915_private *dev_priv)
+{
+	mutex_lock(&dev_priv->dpio_lock);
+
+	/* Enable bandgap fix in GOP driver */
+	vlv_cck_modify(dev_priv, 0x6D, 0x00010000, 0x00030000);
+	msleep(20);
+	vlv_cck_modify(dev_priv, 0x6E, 0x00010000, 0x00030000);
+	msleep(20);
+	vlv_cck_modify(dev_priv, 0x6F, 0x00010000, 0x00030000);
+	msleep(20);
+	vlv_cck_modify(dev_priv, 0x00, 0x00008000, 0x00008000);
+	msleep(20);
+	vlv_cck_modify(dev_priv, 0x00, 0x00000000, 0x00008000);
+	msleep(20);
+
+	/* Turn Display Trunk on */
+	vlv_cck_modify(dev_priv, 0x6B, 0x00020000, 0x00030000);
+	msleep(20);
+
+	vlv_cck_modify(dev_priv, 0x6C, 0x00020000, 0x00030000);
+	msleep(20);
+
+	vlv_cck_modify(dev_priv, 0x6D, 0x00020000, 0x00030000);
+	msleep(20);
+	vlv_cck_modify(dev_priv, 0x6E, 0x00020000, 0x00030000);
+	msleep(20);
+	vlv_cck_modify(dev_priv, 0x6F, 0x00020000, 0x00030000);
+
+	mutex_unlock(&dev_priv->dpio_lock);
+
+	/* Need huge delay, otherwise clock is not stable */
+	msleep(100);
+}
+
 static struct intel_dsi *intel_attached_dsi(struct drm_connector *connector)
 {
 	return container_of(intel_attached_encoder(connector),

@@ -299,6 +344,9 @@ static void intel_dsi_mode_set(struct intel_encoder *intel_encoder)
 	/* Update the DSI PLL */
 	vlv_enable_dsi_pll(intel_encoder);
 
+	/* XXX: Location of the call */
+	band_gap_wa(dev_priv);
+
 	/* escape clock divider, 20MHz, shared for A and C. device ready must be
 	 * off when doing this! txclkesc? */
 	tmp = I915_READ(MIPI_CTRL(0));

Signature · 1 line

1.7.9.5

Jani Nikula

author

2013-08-13 13:28 UTC #17 lore raw

PATCH 12/14 drm/i915: Parse the MIPI related VBT Block and store relevant info

In reply to Jani Nikula

From: Shobhit Kumar <[email protected]>

Initial parsing of the VBT MIPI block. For now, just store the panel id if found.

Signed-off-by Shobhit Kumar <[email protected]>

Signed-off-by Jani Nikula <[email protected]>

---
 drivers/gpu/drm/i915/i915_drv.h   |    5 +++++
 drivers/gpu/drm/i915/intel_bios.c |   16 +++++++++++++++
 drivers/gpu/drm/i915/intel_bios.h |   41 +++++++++++++++++++++++++++++++++++++
 3 files changed, 62 insertions(+)

drivers/gpu/drm/i915/i915_drv.h +5 -0

index 6db95a2..5be251b 100644
@@ -1053,6 +1053,11 @@ struct intel_vbt_data {
 	int edp_bpp;
 	struct edp_power_seq edp_pps;
 
+	/* MIPI DSI */
+	struct {
+		u16 panel_id;
+	} dsi;
+
 	int crt_ddc_pin;
 
 	int child_dev_num;

drivers/gpu/drm/i915/intel_bios.c +16 -0

index 53f2bed..6668873 100644
@@ -569,6 +569,21 @@ parse_edp(struct drm_i915_private *dev_priv, struct bdb_header *bdb)
 }
 
 static void
+parse_mipi(struct drm_i915_private *dev_priv, struct bdb_header *bdb)
+{
+	struct bdb_mipi *mipi;
+
+	mipi = find_section(bdb, BDB_MIPI);
+	if (!mipi) {
+		DRM_DEBUG_KMS("No MIPI BDB found");
+		return;
+	}
+
+	/* XXX: add more info */
+	dev_priv->vbt.dsi.panel_id = mipi->panel_id;
+}
+
+static void
 parse_device_mapping(struct drm_i915_private *dev_priv,
 		       struct bdb_header *bdb)
 {

@@ -745,6 +760,7 @@ intel_parse_bios(struct drm_device *dev)
 	parse_device_mapping(dev_priv, bdb);
 	parse_driver_features(dev_priv, bdb);
 	parse_edp(dev_priv, bdb);
+	parse_mipi(dev_priv, bdb);
 
 	if (bios)
 		pci_unmap_rom(pdev, bios);

drivers/gpu/drm/i915/intel_bios.h +41 -0

51 lines not on this page · raw message

Signature · 1 line

1.7.9.5

Jani Nikula

author

2013-08-13 13:28 UTC #18 lore raw

PATCH 13/14 drm/i915: initialize DSI output on VLV

In reply to Jani Nikula

Signed-off-by Jani Nikula <[email protected]>

---
 drivers/gpu/drm/i915/intel_display.c |    2 ++
 1 file changed, 2 insertions(+)

drivers/gpu/drm/i915/intel_display.c +2 -0

index e3ca335..7edb9c0 100644
@@ -9357,6 +9357,8 @@ static void intel_setup_outputs(struct drm_device *dev)
 			if (I915_READ(VLV_DISPLAY_BASE + DP_B) & DP_DETECTED)
 				intel_dp_init(dev, VLV_DISPLAY_BASE + DP_B, PORT_B);
 		}
+
+		intel_dsi_init(dev);
 	} else if (SUPPORTS_DIGITAL_OUTPUTS(dev)) {
 		bool found = false;

Signature · 1 line

1.7.9.5

Jani Nikula

author

2013-08-13 13:28 UTC #19 lore raw

PATCH 14/14 drm/i915: add AUO MIPI DSI display sub-encoder

In reply to Jani Nikula

From: Shobhit Kumar <[email protected]>

Signed-off-by Shobhit Kumar <[email protected]>

Signed-off-by Jani Nikula <[email protected]>

---
 drivers/gpu/drm/i915/Makefile          |    1 +
 drivers/gpu/drm/i915/auo_dsi_display.c |  182 ++++++++++++++++++++++++++++++++
 drivers/gpu/drm/i915/intel_dsi.c       |    5 +
 drivers/gpu/drm/i915/intel_dsi.h       |    3 +
 4 files changed, 191 insertions(+)
 create mode 100644 drivers/gpu/drm/i915/auo_dsi_display.c

drivers/gpu/drm/i915/Makefile +1 -0

index 65e60d2..18bf236 100644
@@ -42,6 +42,7 @@ i915-y := i915_drv.o i915_dma.o i915_irq.o \
 	  intel_opregion.o \
 	  intel_sideband.o \
 	  intel_uncore.o \
+	  auo_dsi_display.o \
 	  dvo_ch7xxx.o \
 	  dvo_ch7017.o \
 	  dvo_ivch.o \

drivers/gpu/drm/i915/auo_dsi_display.c new file +182 -0

182 lines not on this page · raw message

drivers/gpu/drm/i915/intel_dsi.c +5 -0

index d28be01..a78f4f3 100644
@@ -35,6 +35,11 @@
 
 /* the sub-encoders aka panel drivers */
 static const struct intel_dsi_device intel_dsi_devices[] = {
+	{
+		.type = INTEL_DSI_VIDEO_MODE,
+		.name = "auo-dsi-vid-mode-display",
+		.dev_ops = &auo_dsi_display_ops,
+	},
 };

drivers/gpu/drm/i915/intel_dsi.h +3 -0

index 0e0a212..05f5ba1 100644
@@ -98,4 +98,7 @@ static inline struct intel_dsi *enc_to_intel_dsi(struct drm_encoder *encoder)
 
 extern void vlv_enable_dsi_pll(struct intel_encoder *encoder);
 
+/* the panel drivers */
+extern struct intel_dsi_dev_ops auo_dsi_display_ops;
+
 #endif /* _INTEL_DSI_H */

Signature · 6 lines

1.7.9.5

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

Daniel Vetter

2013-08-13 22:17 UTC #13 lore raw

Re: [PATCH 08/14] drm/i915: add basic MIPI DSI output support

In reply to Jani Nikula

Quoted 4 lines · Jani Nikula

This does not include any panel specific sub-encoders yet.
Signed-off-by Jani Nikula <[email protected]>
Signed-off-by Shobhit Kumar <[email protected]>

Quick bikesheed on how you wire up the get_modes stuff, mostly because I'm just discussing this on irc with Rob:
- We now have intel_connector->panel.fixed_mode
- And I think it's better to route all the get_modes stuff entirely through the connector layer, leaving the dsi encoder entirely out of the picture. Maybe we should even go as far as registering the drm_connector from the dsi sink device since that one really knows all the details (like all the properties of the panel, what mode it supports or whether maybe this DSI thingy is actually some transcoder with a totally different output attached ...).

Cheers, Daniel

Quoted 592 lines

---
 drivers/gpu/drm/i915/Makefile    |    1 +
 drivers/gpu/drm/i915/intel_drv.h |    1 +
 drivers/gpu/drm/i915/intel_dsi.c |  548 ++++++++++++++++++++++++++++++++++++++
 3 files changed, 550 insertions(+)
 create mode 100644 drivers/gpu/drm/i915/intel_dsi.c

drivers/gpu/drm/i915/Makefile +1 -0

index 8bffd29..5864c5b 100644
@@ -21,6 +21,7 @@ i915-y := i915_drv.o i915_dma.o i915_irq.o \
 	  intel_display.o \
 	  intel_crt.o \
 	  intel_lvds.o \
+	  intel_dsi.o \
 	  intel_dsi_cmd.o \
 	  intel_bios.o \
 	  intel_ddi.o \

drivers/gpu/drm/i915/intel_drv.h +1 -0

index a31abc6..cbe3df1 100644
@@ -525,6 +525,7 @@ extern void intel_mark_fb_busy(struct drm_i915_gem_object *obj,
 			       struct intel_ring_buffer *ring);
 extern void intel_mark_idle(struct drm_device *dev);
 extern void intel_lvds_init(struct drm_device *dev);
+extern bool intel_dsi_init(struct drm_device *dev);
 extern bool intel_is_dual_link_lvds(struct drm_device *dev);
 extern void intel_dp_init(struct drm_device *dev, int output_reg,
 			  enum port port);

drivers/gpu/drm/i915/intel_dsi.c new file +548 -0

new file mode 100644
index 0000000..aa81dd8
@@ -0,0 +1,548 @@
+/*
+ * Copyright © 2013 Intel Corporation
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice (including the next
+ * paragraph) shall be included in all copies or substantial portions of the
+ * Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
+ * DEALINGS IN THE SOFTWARE.
+ *
+ * Author: Jani Nikula <[email protected]>
+ */
+
+#include <drm/drmP.h>
+#include <drm/drm_crtc.h>
+#include <drm/drm_edid.h>
+#include <drm/i915_drm.h>
+#include <linux/slab.h>
+#include "i915_drv.h"
+#include "intel_drv.h"
+#include "intel_dsi.h"
+#include "intel_dsi_cmd.h"
+
+/* the sub-encoders aka panel drivers */
+static const struct intel_dsi_device intel_dsi_devices[] = {
+};
+
+static struct intel_dsi *intel_attached_dsi(struct drm_connector *connector)
+{
+	return container_of(intel_attached_encoder(connector),
+			    struct intel_dsi, base);
+}
+
+static inline bool is_vid_mode(struct intel_dsi *intel_dsi)
+{
+	return intel_dsi->dev.type == INTEL_DSI_VIDEO_MODE;
+}
+
+static inline bool is_cmd_mode(struct intel_dsi *intel_dsi)
+{
+	return intel_dsi->dev.type == INTEL_DSI_COMMAND_MODE;
+}
+
+static void intel_dsi_hot_plug(struct intel_encoder *encoder)
+{
+	DRM_DEBUG_KMS("\n");
+}
+
+static bool intel_dsi_compute_config(struct intel_encoder *encoder,
+				     struct intel_crtc_config *config)
+{
+	DRM_DEBUG_KMS("\n");
+	return true;
+}
+
+static void intel_dsi_pre_pll_enable(struct intel_encoder *encoder)
+{
+	DRM_DEBUG_KMS("\n");
+}
+
+static void intel_dsi_pre_enable(struct intel_encoder *encoder)
+{
+	DRM_DEBUG_KMS("\n");
+}
+
+static void intel_dsi_enable(struct intel_encoder *encoder)
+{
+	struct drm_i915_private *dev_priv = encoder->base.dev->dev_private;
+	struct intel_crtc *intel_crtc = to_intel_crtc(encoder->base.crtc);
+	struct intel_dsi *intel_dsi = enc_to_intel_dsi(&encoder->base);
+	int pipe = intel_crtc->pipe;
+	u32 temp;
+
+	DRM_DEBUG_KMS("\n");
+
+	temp = I915_READ(MIPI_DEVICE_READY(pipe));
+	temp &= ~ULPS_STATE_MASK;
+	temp &= ~DEVICE_READY; /* XXX: assuming it's already !ready */
+	I915_WRITE(MIPI_DEVICE_READY(pipe), temp | ULPS_STATE_EXIT);
+	msleep(20); /* XXX */
+	I915_WRITE(MIPI_DEVICE_READY(pipe), temp);
+	msleep(20); /* XXX */
+	I915_WRITE(MIPI_DEVICE_READY(pipe), temp | DEVICE_READY);
+
+	if (is_cmd_mode(intel_dsi))
+		I915_WRITE(MIPI_MAX_RETURN_PKT_SIZE(pipe), 8 * 4);
+
+	/* Do this here, or let the slave encoder do it in ->dpms? */
+	if (is_vid_mode(intel_dsi)) {
+		dpi_send_cmd(intel_dsi, TURN_ON);
+		msleep(100);
+	}
+
+	/* assert ip_tg_enable signal */
+	temp = I915_READ(MIPI_PORT_CTRL(pipe));
+	I915_WRITE(MIPI_PORT_CTRL(pipe), temp | DPI_ENABLE);
+	POSTING_READ(MIPI_PORT_CTRL(pipe));
+
+	intel_dsi->dev.dev_ops->enable(&intel_dsi->dev);
+}
+
+static void intel_dsi_disable(struct intel_encoder *encoder)
+{
+	struct drm_i915_private *dev_priv = encoder->base.dev->dev_private;
+	struct intel_crtc *intel_crtc = to_intel_crtc(encoder->base.crtc);
+	struct intel_dsi *intel_dsi = enc_to_intel_dsi(&encoder->base);
+	int pipe = intel_crtc->pipe;
+	u32 temp;
+
+	DRM_DEBUG_KMS("\n");
+
+	intel_dsi->dev.dev_ops->disable(&intel_dsi->dev);
+
+	if (is_vid_mode(intel_dsi))
+		dpi_send_cmd(intel_dsi, SHUTDOWN);
+
+	if (is_vid_mode(intel_dsi)) {
+		/* de-assert ip_tg_enable signal */
+		temp = I915_READ(MIPI_PORT_CTRL(pipe));
+		I915_WRITE(MIPI_PORT_CTRL(pipe), temp & ~DPI_ENABLE);
+		POSTING_READ(MIPI_PORT_CTRL(pipe));
+	}
+
+	/* XXX: wait for fifos before ulps entry */
+
+	temp = I915_READ(MIPI_DEVICE_READY(pipe));
+	temp &= ~ULPS_STATE_MASK;
+	temp &= ~DEVICE_READY;
+	I915_WRITE(MIPI_DEVICE_READY(pipe), temp);
+	msleep(5);
+	I915_WRITE(MIPI_DEVICE_READY(pipe), temp | ULPS_STATE_ENTER);
+}
+
+static void intel_dsi_post_disable(struct intel_encoder *encoder)
+{
+	DRM_DEBUG_KMS("\n");
+
+	/* XXX: disable dsi pll */
+}
+
+static bool intel_dsi_get_hw_state(struct intel_encoder *encoder,
+				   enum pipe *pipe)
+{
+	struct intel_crtc *intel_crtc = to_intel_crtc(encoder->base.crtc);
+
+	DRM_DEBUG_KMS("\n");
+
+	/* XXX: this is wrong */
+	if (intel_crtc) {
+		*pipe = intel_crtc->pipe;
+		return true;
+	}
+
+	/* XXX: do we also need to call
+	 * intel_dsi->dev.dev_ops->get_hw_state(&intel_dsi->dev);
+	 */
+
+	return false;
+}
+
+static void intel_dsi_get_config(struct intel_encoder *encoder,
+				 struct intel_crtc_config *pipe_config)
+{
+	DRM_DEBUG_KMS("\n");
+}
+
+static int intel_dsi_mode_valid(struct drm_connector *connector,
+				struct drm_display_mode *mode)
+{
+	struct intel_dsi *intel_dsi = intel_attached_dsi(connector);
+
+	DRM_DEBUG_KMS("\n");
+
+	if (mode->flags & DRM_MODE_FLAG_DBLSCAN) {
+		DRM_DEBUG_KMS("MODE_NO_DBLESCAN\n");
+		return MODE_NO_DBLESCAN;
+	}
+
+	if (intel_dsi->panel_fixed_mode) {
+		if (mode->hdisplay > intel_dsi->panel_fixed_mode->hdisplay)
+			return MODE_PANEL;
+		if (mode->vdisplay > intel_dsi->panel_fixed_mode->vdisplay)
+			return MODE_PANEL;
+	}
+
+	return intel_dsi->dev.dev_ops->mode_valid(&intel_dsi->dev, mode);
+}
+
+static bool intel_dsi_mode_fixup(struct drm_encoder *encoder,
+				 const struct drm_display_mode *mode,
+				 struct drm_display_mode *adjusted_mode)
+{
+	struct intel_dsi *intel_dsi = enc_to_intel_dsi(encoder);
+
+	DRM_DEBUG_KMS("\n");
+
+	/* If we have timings from the BIOS for the panel, put them in
+	 * to the adjusted mode.  The CRTC will be set up for this mode,
+	 * with the panel scaling set up to source from the H/VDisplay
+	 * of the original mode.
+	 */
+	if (intel_dsi->panel_fixed_mode != NULL) {
+#define C(x) adjusted_mode->x = intel_dsi->panel_fixed_mode->x
+		C(hdisplay);
+		C(hsync_start);
+		C(hsync_end);
+		C(htotal);
+		C(vdisplay);
+		C(vsync_start);
+		C(vsync_end);
+		C(vtotal);
+		C(clock);
+#undef C
+	}
+
+	if (intel_dsi->dev.dev_ops->mode_fixup)
+		return intel_dsi->dev.dev_ops->mode_fixup(&intel_dsi->dev, mode, adjusted_mode);
+
+	return true;
+}
+
+/* return pixels in terms of txbyteclkhs */
+static u16 txbyteclkhs(u16 pixels, int bpp, int lane_count)
+{
+	return DIV_ROUND_UP(DIV_ROUND_UP(pixels * bpp, 8), lane_count);
+}
+
+static void set_dsi_timings(struct drm_encoder *encoder,
+			    const struct drm_display_mode *mode)
+{
+	struct drm_device *dev = encoder->dev;
+	struct drm_i915_private *dev_priv = dev->dev_private;
+	struct intel_crtc *intel_crtc = to_intel_crtc(encoder->crtc);
+	struct intel_dsi *intel_dsi = enc_to_intel_dsi(encoder);
+	int pipe = intel_crtc->pipe;
+	unsigned int bpp = intel_crtc->config.pipe_bpp;
+	unsigned int lane_count = intel_dsi->lane_count;
+
+	u16 hactive, hfp, hsync, hbp, vfp, vsync, vbp;
+
+	hactive = mode->hdisplay;
+	hfp = mode->hsync_start - mode->hdisplay;
+	hsync = mode->hsync_end - mode->hsync_start;
+	hbp = mode->htotal - mode->hsync_end;
+
+	vfp = mode->vsync_start - mode->vdisplay;
+	vsync = mode->vsync_end - mode->vsync_start;
+	vbp = mode->vtotal - mode->vsync_end;
+
+	/* horizontal values are in terms of high speed byte clock */
+	hactive = txbyteclkhs(hactive, bpp, lane_count);
+	hfp = txbyteclkhs(hfp, bpp, lane_count);
+	hsync = txbyteclkhs(hsync, bpp, lane_count);
+	hbp = txbyteclkhs(hbp, bpp, lane_count);
+
+	I915_WRITE(MIPI_HACTIVE_AREA_COUNT(pipe), hactive);
+	I915_WRITE(MIPI_HFP_COUNT(pipe), hfp);
+
+	/* meaningful for video mode non-burst sync pulse mode only, can be zero
+	 * for non-burst sync events and burst modes */
+	I915_WRITE(MIPI_HSYNC_PADDING_COUNT(pipe), hsync);
+	I915_WRITE(MIPI_HBP_COUNT(pipe), hbp);
+
+	/* vertical values are in terms of lines */
+	I915_WRITE(MIPI_VFP_COUNT(pipe), vfp);
+	I915_WRITE(MIPI_VSYNC_PADDING_COUNT(pipe), vsync);
+	I915_WRITE(MIPI_VBP_COUNT(pipe), vbp);
+}
+
+static void intel_dsi_mode_set(struct intel_encoder *intel_encoder)
+{
+	struct drm_encoder *encoder = &intel_encoder->base;
+	struct drm_device *dev = encoder->dev;
+	struct drm_i915_private *dev_priv = dev->dev_private;
+	struct intel_crtc *intel_crtc = to_intel_crtc(encoder->crtc);
+	struct intel_dsi *intel_dsi = enc_to_intel_dsi(encoder);
+	struct drm_display_mode *adjusted_mode =
+		&intel_crtc->config.adjusted_mode;
+	int pipe = intel_crtc->pipe;
+	unsigned int bpp = intel_crtc->config.pipe_bpp;
+	u32 val, tmp;
+
+	DRM_DEBUG_KMS("pipe %d\n", pipe);
+
+	/* escape clock divider, 20MHz, shared for A and C. device ready must be
+	 * off when doing this! txclkesc? */
+	tmp = I915_READ(MIPI_CTRL(0));
+	tmp &= ~ESCAPE_CLOCK_DIVIDER_MASK;
+	I915_WRITE(MIPI_CTRL(0), tmp | ESCAPE_CLOCK_DIVIDER_1);
+
+	/* read request priority is per pipe */
+	tmp = I915_READ(MIPI_CTRL(pipe));
+	tmp &= ~READ_REQUEST_PRIORITY_MASK;
+	I915_WRITE(MIPI_CTRL(pipe), tmp | READ_REQUEST_PRIORITY_HIGH);
+
+	/* XXX: why here, why like this? handling in irq handler?! */
+	I915_WRITE(MIPI_INTR_STAT(pipe), 0xffffffff);
+	I915_WRITE(MIPI_INTR_EN(pipe), 0xffffffff);
+
+	I915_WRITE(MIPI_DPHY_PARAM(pipe),
+		   0x3c << EXIT_ZERO_COUNT_SHIFT |
+		   0x1f << TRAIL_COUNT_SHIFT |
+		   0xc5 << CLK_ZERO_COUNT_SHIFT |
+		   0x1f << PREPARE_COUNT_SHIFT);
+
+	I915_WRITE(MIPI_DPI_RESOLUTION(pipe),
+		   adjusted_mode->vdisplay << VERTICAL_ADDRESS_SHIFT |
+		   adjusted_mode->hdisplay << HORIZONTAL_ADDRESS_SHIFT);
+
+	set_dsi_timings(encoder, adjusted_mode);
+
+	val = intel_dsi->lane_count << DATA_LANES_PRG_REG_SHIFT;
+	if (is_cmd_mode(intel_dsi)) {
+		val |= intel_dsi->channel << CMD_MODE_CHANNEL_NUMBER_SHIFT;
+		val |= CMD_MODE_DATA_WIDTH_8_BIT; /* XXX */
+	} else {
+		val |= intel_dsi->channel << VID_MODE_CHANNEL_NUMBER_SHIFT;
+
+		/* XXX: cross-check bpp vs. pixel format? */
+		val |= intel_dsi->pixel_format;
+	}
+	I915_WRITE(MIPI_DSI_FUNC_PRG(pipe), val);
+
+	/* timeouts for recovery. one frame IIUC. if counter expires, EOT and
+	 * stop state. */
+
+	if (is_vid_mode(intel_dsi) &&
+	    intel_dsi->video_mode_format == VIDEO_MODE_BURST) {
+		I915_WRITE(MIPI_HS_TX_TIMEOUT(pipe),
+			   txbyteclkhs(adjusted_mode->htotal + 1, bpp,
+				       intel_dsi->lane_count));
+	} else {
+		I915_WRITE(MIPI_HS_TX_TIMEOUT(pipe),
+			   txbyteclkhs(adjusted_mode->vtotal *
+				       adjusted_mode->htotal,
+				       bpp, intel_dsi->lane_count));
+	}
+	I915_WRITE(MIPI_LP_RX_TIMEOUT(pipe), 0xffff);
+	I915_WRITE(MIPI_TURN_AROUND_TIMEOUT(pipe), 0x14);
+
+	I915_WRITE(MIPI_DEVICE_RESET_TIMER(pipe), 0xffff);
+
+	/* dphy stuff */
+
+	/* in terms of low power clock */
+	I915_WRITE(MIPI_INIT_COUNT(pipe), 0x7d0);
+
+	/* recovery disables */
+	I915_WRITE(MIPI_EOT_DISABLE(pipe), intel_dsi->eot_disable);
+
+	/* in terms of txbyteclkhs. actual high to low switch +
+	 * MIPI_STOP_STATE_STALL * MIPI_LP_BYTECLK.
+	 *
+	 * XXX: write MIPI_STOP_STATE_STALL?
+	 */
+	I915_WRITE(MIPI_HIGH_LOW_SWITCH_COUNT(pipe), 0x46);
+
+	/* XXX: low power clock equivalence in terms of byte clock. the number
+	 * of byte clocks occupied in one low power clock. based on txbyteclkhs
+	 * and txclkesc. txclkesc time / txbyteclk time * (105 +
+	 * MIPI_STOP_STATE_STALL) / 105.???
+	 */
+	I915_WRITE(MIPI_LP_BYTECLK(pipe), 4);
+
+	/* the bw essential for transmitting 16 long packets containing 252
+	 * bytes meant for dcs write memory command is programmed in this
+	 * register in terms of byte clocks. based on dsi transfer rate and the
+	 * number of lanes configured the time taken to transmit 16 long packets
+	 * in a dsi stream varies. */
+	I915_WRITE(MIPI_DBI_BW_CTRL(pipe), 0x820);
+
+	I915_WRITE(MIPI_CLK_LANE_SWITCH_TIME_CNT(pipe),
+		   0xa << LP_HS_SSW_CNT_SHIFT |
+		   0x14 << HS_LP_PWR_SW_CNT_SHIFT);
+
+	if (is_vid_mode(intel_dsi))
+		I915_WRITE(MIPI_VIDEO_MODE_FORMAT(pipe),
+			   intel_dsi->video_mode_format);
+}
+
+static enum drm_connector_status
+intel_dsi_detect(struct drm_connector *connector, bool force)
+{
+	struct intel_dsi *intel_dsi = intel_attached_dsi(connector);
+	DRM_DEBUG_KMS("\n");
+	return intel_dsi->dev.dev_ops->detect(&intel_dsi->dev);
+}
+
+static int intel_dsi_get_modes(struct drm_connector *connector)
+{
+	struct intel_dsi *intel_dsi = intel_attached_dsi(connector);
+	struct drm_display_mode *mode;
+
+	DRM_DEBUG_KMS("\n");
+
+	if (!intel_dsi->panel_fixed_mode) {
+		DRM_DEBUG_KMS("no fixed mode\n");
+		return 0;
+	}
+
+	mode = drm_mode_duplicate(connector->dev, intel_dsi->panel_fixed_mode);
+	if (!mode) {
+		DRM_DEBUG_KMS("dupe failed\n");
+		return 0;
+	}
+
+	drm_mode_probed_add(connector, mode);
+	return 1;
+}
+
+static void intel_dsi_destroy(struct drm_connector *connector)
+{
+	DRM_DEBUG_KMS("\n");
+	drm_sysfs_connector_remove(connector);
+	drm_connector_cleanup(connector);
+	kfree(connector);
+}
+
+static const struct drm_encoder_helper_funcs intel_dsi_helper_funcs = {
+	.mode_fixup = intel_dsi_mode_fixup,
+};
+
+static const struct drm_encoder_funcs intel_dsi_funcs = {
+	.destroy = intel_encoder_destroy,
+};
+
+static const struct drm_connector_helper_funcs intel_dsi_connector_helper_funcs = {
+	.get_modes = intel_dsi_get_modes,
+	.mode_valid = intel_dsi_mode_valid,
+	.best_encoder = intel_best_encoder,
+};
+
+static const struct drm_connector_funcs intel_dsi_connector_funcs = {
+	.dpms = intel_connector_dpms,
+	.detect = intel_dsi_detect,
+	.destroy = intel_dsi_destroy,
+	.fill_modes = drm_helper_probe_single_connector_modes,
+};
+
+bool intel_dsi_init(struct drm_device *dev)
+{
+	struct intel_dsi *intel_dsi;
+	struct intel_encoder *intel_encoder;
+	struct drm_encoder *encoder;
+	struct intel_connector *intel_connector;
+	struct drm_connector *connector;
+	struct drm_display_mode *fixed_mode = NULL;
+	const struct intel_dsi_device *dsi;
+	unsigned int i;
+
+	DRM_DEBUG_KMS("\n");
+
+	intel_dsi = kzalloc(sizeof(*intel_dsi), GFP_KERNEL);
+	if (!intel_dsi)
+		return false;
+
+	intel_connector = kzalloc(sizeof(*intel_connector), GFP_KERNEL);
+	if (!intel_connector) {
+		kfree(intel_dsi);
+		return false;
+	}
+
+	intel_encoder = &intel_dsi->base;
+	encoder = &intel_encoder->base;
+
+	connector = &intel_connector->base;
+
+	drm_encoder_init(dev, encoder, &intel_dsi_funcs, DRM_MODE_ENCODER_DSI);
+
+	/* XXX: very likely not all of these are needed */
+	intel_encoder->hot_plug = intel_dsi_hot_plug;
+	intel_encoder->compute_config = intel_dsi_compute_config;
+	intel_encoder->pre_pll_enable = intel_dsi_pre_pll_enable;
+	intel_encoder->pre_enable = intel_dsi_pre_enable;
+	intel_encoder->enable = intel_dsi_enable;
+	intel_encoder->mode_set = intel_dsi_mode_set;
+	intel_encoder->disable = intel_dsi_disable;
+	intel_encoder->post_disable = intel_dsi_post_disable;
+	intel_encoder->get_hw_state = intel_dsi_get_hw_state;
+	intel_encoder->get_config = intel_dsi_get_config;
+
+	intel_connector->get_hw_state = intel_connector_get_hw_state;
+
+	for (i = 0; i < ARRAY_SIZE(intel_dsi_devices); i++) {
+		dsi = &intel_dsi_devices[i];
+		intel_dsi->dev = *dsi;
+
+		if (dsi->dev_ops->init(&intel_dsi->dev))
+			break;
+	}
+
+	if (i == ARRAY_SIZE(intel_dsi_devices)) {
+		DRM_DEBUG_KMS("no device found\n");
+		goto err;
+	}
+
+	intel_encoder->type = INTEL_OUTPUT_DSI;
+	intel_encoder->crtc_mask = (1 << 0); /* XXX */
+
+	intel_encoder->cloneable = false;
+	drm_connector_init(dev, connector, &intel_dsi_connector_funcs,
+			   DRM_MODE_CONNECTOR_DSI);
+
+	drm_connector_helper_add(connector, &intel_dsi_connector_helper_funcs);
+
+	connector->display_info.subpixel_order = SubPixelHorizontalRGB; /*XXX*/
+	connector->interlace_allowed = false;
+	connector->doublescan_allowed = false;
+
+	drm_encoder_helper_add(encoder, &intel_dsi_helper_funcs);
+
+	intel_connector_attach_encoder(intel_connector, intel_encoder);
+
+	drm_sysfs_connector_add(connector);
+
+	fixed_mode = dsi->dev_ops->get_modes(&intel_dsi->dev);
+	if (!fixed_mode) {
+		DRM_DEBUG_KMS("no fixed mode\n");
+		goto err;
+	}
+
+	fixed_mode->type |= DRM_MODE_TYPE_PREFERRED;
+
+	intel_dsi->panel_fixed_mode = fixed_mode;
+
+	intel_panel_init(&intel_connector->panel, fixed_mode);
+
+	return true;
+
+err:
+	drm_encoder_cleanup(&intel_encoder->base);
+	kfree(intel_dsi);
+	kfree(intel_connector);
+
+	return false;
+}

Signature · 6 lines

1.7.9.5

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

Signature · 3 lines

Daniel Vetter
Software Engineer, Intel Corporation
+41 (0) 79 365 57 48 - http://blog.ffwll.ch

Ville Syrjälä

2013-08-14 13:59 UTC #5 lore raw

Re: [PATCH 04/14] drm/i915: add MIPI DSI register definitions

In reply to Jani Nikula

Quoted 17 lines · Jani Nikula

Add definitions for VLV MIPI DSI registers.

Signed-off-by Jani Nikula <[email protected]>

---
 drivers/gpu/drm/i915/i915_reg.h |  409 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 409 insertions(+)

drivers/gpu/drm/i915/i915_reg.h +2 -0

index aced53a..32e32b6 100644
@@ -5104,4 +5104,413 @@
 #define PIPE_CSC_POSTOFF_ME(pipe) _PIPE(pipe, _PIPE_A_CSC_POSTOFF_ME, _PIPE_B_CSC_POSTOFF_ME)
 #define PIPE_CSC_POSTOFF_LO(pipe) _PIPE(pipe, _PIPE_A_CSC_POSTOFF_LO, _PIPE_B_CSC_POSTOFF_LO)
 
+/* VLV MIPI registers */
+

drivers/gpu/drm/i915/i915_reg.h line 5118

Quoted 10 lines

drivers/gpu/drm/i915/i915_reg.h +10 -0

+/* XXX: This register seems very messy. MIPIB has only enable and delay. */
+#define _MIPIA_PORT_CTRL			(VLV_DISPLAY_BASE + 0x61190)
+#define _MIPIB_PORT_CTRL			(VLV_DISPLAY_BASE + 0x61700)
+#define MIPI_PORT_CTRL(pipe)		_PIPE(pipe, _MIPIA_PORT_CTRL, _MIPIB_PORT_CTRL)
+#define  DPI_ENABLE					(1 << 31) /* A + B */
+#define  MIPIA_MIPI4DPHY_DELAY_COUNT_SHIFT		27
+#define  MIPIA_MIPI4DPHY_DELAY_COUNT_MASK		(0xf << 27)
+#define  DUAL_LINK_MODE_MASK				(1 << 26)
+#define  DUAL_LINK_MODE_FRONT_BACK			(0 << 26)
+#define  DUAL_LINK_MODE_PIXEL_ALTERNATIVE		(1 << 26)

25 is "Dither Enable" according to my docs.

drivers/gpu/drm/i915/i915_reg.h line 5120

Quoted 2 lines

drivers/gpu/drm/i915/i915_reg.h +2 -0

+#define  FLOPPED_HSTX					(1 << 23)
+#define  DE_INVERT					(1 << 19) /* XXX */

One doc has DE_INVERT (and HS/VS invert and border enable bits), another has the FLISDSI stuff. I guess that's the XXX here.

drivers/gpu/drm/i915/i915_reg.h line 5123

Quoted 3 lines

drivers/gpu/drm/i915/i915_reg.h +3 -0

+#define  MIPIA_FLISDSI_DELAY_COUNT_SHIFT		18
+#define  MIPIA_FLISDSI_DELAY_COUNT_MASK			(0xf << 18)
+#define  AFE_LATCHOUT					(1 << 17)

16 is "LPOutput Hold"

Quoted 24 lines

drivers/gpu/drm/i915/i915_reg.h +24 -0

+#define  MIPIB_FLISDSI_DELAY_COUNT_HIGH_SHIFT		15
+#define  MIPIB_FLISDSI_DELAY_COUNT_HIGH_MASK		(1 << 15)
+#define  MIPIB_MIPI4DPHY_DELAY_COUNT_SHIFT		11
+#define  MIPIB_MIPI4DPHY_DELAY_COUNT_MASK		(0xf << 11)
+#define  CSB_SHIFT					9
+#define  CSB_MASK					(3 << 9)
+#define  CSB_20MHZ					(0 << 9)
+#define  CSB_10MHZ					(1 << 9)
+#define  CSB_40MHZ					(2 << 9)
+#define  BANDGAP_MASK					(1 << 8)
+#define  BANDGAP_PNW_CIRCUIT				(0 << 8)
+#define  BANDGAP_LNC_CIRCUIT				(1 << 8)
+#define  MIPIB_FLISDSI_DELAY_COUNT_LOW_SHIFT		5
+#define  MIPIB_FLISDSI_DELAY_COUNT_LOW_MASK		(7 << 5)
+#define  TEARING_EFFECT_DELAY				(1 << 4) /* A + B */
+#define  TEARING_EFFECT_SHIFT				2 /* A + B */
+#define  TEARING_EFFECT_MASK				(3 << 2)
+#define  TEARING_EFFECT_OFF				(0 << 2)
+#define  TEARING_EFFECT_DSI				(1 << 2)
+#define  TEARING_EFFECT_GPIO				(2 << 2)
+#define  LANE_CONFIGURATION_SHIFT			0
+#define  LANE_CONFIGURATION_MASK			(3 << 0)
+#define  LANE_CONFIGURATION_4LANE			(0 << 0)
+#define  LANE_CONFIGURATION_DUAL_LINK_A			(1 << 0)

drivers/gpu/drm/i915/i915_reg.h line 5157

Quoted 10 lines

drivers/gpu/drm/i915/i915_reg.h +10 -0

+#define  LANE_CONFIGURATION_DUAL_LINK_B			(2 << 0)
+
+#define _MIPIA_TEARING_CTRL			(VLV_DISPLAY_BASE + 0x61194)
+#define _MIPIB_TEARING_CTRL			(VLV_DISPLAY_BASE + 0x61704)
+#define MIPI_TEARING_CTRL(pipe)		_PIPE(pipe, _MIPIA_TEARING_CTRL, _MIPIB_TEARING_CTRL)
+#define  TEARING_EFFECT_DELAY_SHIFT			0
+#define  TEARING_EFFECT_DELAY_MASK			(0xffff << 0)
+
+/* XXX */
+#define _MIPIA_AUTOPWG				(VLV_DISPLAY_BASE + 0x611a0)

Is the XXX here because the spec says the contents are all "reserved"?

drivers/gpu/drm/i915/i915_reg.h line 5167

Quoted 10 lines

drivers/gpu/drm/i915/i915_reg.h +10 -0

+
+/* MIPI DSI Controller and D-PHY registers */
+
+#define _MIPIA_DEVICE_READY			(VLV_DISPLAY_BASE + 0xb000)
+#define _MIPIB_DEVICE_READY			(VLV_DISPLAY_BASE + 0xb800)
+#define MIPI_DEVICE_READY(pipe)		_PIPE(pipe, _MIPIA_DEVICE_READY, _MIPIB_DEVICE_READY)
+#define  BUS_POSSESSION					(1 << 3) /* set to give bus to receiver */
+#define  ULPS_STATE_MASK				(3 << 1)
+#define  ULPS_STATE_ENTER				(2 << 1) /* XXX */
+#define  ULPS_STATE_EXIT				(1 << 1) /* XXX */

Maybe we should have the (0 << 1) "normal operation" listed here as well?

Quoted 85 lines

drivers/gpu/drm/i915/i915_reg.h +85 -0

+#define  DEVICE_READY					(1 << 0)
+
+#define _MIPIA_INTR_STAT			(VLV_DISPLAY_BASE + 0xb004)
+#define _MIPIB_INTR_STAT			(VLV_DISPLAY_BASE + 0xb804)
+#define MIPI_INTR_STAT(pipe)		_PIPE(pipe, _MIPIA_INTR_STAT, _MIPIB_INTR_STAT)
+#define _MIPIA_INTR_EN				(VLV_DISPLAY_BASE + 0xb008)
+#define _MIPIB_INTR_EN				(VLV_DISPLAY_BASE + 0xb808)
+#define MIPI_INTR_EN(pipe)		_PIPE(pipe, _MIPIA_INTR_EN, _MIPIB_INTR_EN)
+#define  TEARING_EFFECT					(1 << 31)
+#define  SPL_PKT_SENT_INTERRUPT				(1 << 30)
+#define  GEN_READ_DATA_AVAIL				(1 << 29)
+#define  LP_GENERIC_WR_FIFO_FULL			(1 << 28)
+#define  HS_GENERIC_WR_FIFO_FULL			(1 << 27)
+#define  RX_PROT_VIOLATION				(1 << 26)
+#define  RX_INVALID_TX_LENGTH				(1 << 25)
+#define  ACK_WITH_NO_ERROR				(1 << 24)
+#define  TURN_AROUND_ACK_TIMEOUT			(1 << 23)
+#define  LP_RX_TIMEOUT					(1 << 22)
+#define  HS_TX_TIMEOUT					(1 << 21)
+#define  DPI_FIFO_UNDERRUN				(1 << 20)
+#define  LOW_CONTENTION					(1 << 19)
+#define  HIGH_CONTENTION				(1 << 18)
+#define  TXDSI_VC_ID_INVALID				(1 << 17)
+#define  TXDSI_DATA_TYPE_NOT_RECOGNISED			(1 << 16)
+#define  TXCHECKSUM_ERROR				(1 << 15)
+#define  TXECC_MULTIBIT_ERROR				(1 << 14)
+#define  TXECC_SINGLE_BIT_ERROR				(1 << 13)
+#define  TXFALSE_CONTROL_ERROR				(1 << 12)
+#define  RXDSI_VC_ID_INVALID				(1 << 11)
+#define  RXDSI_DATA_TYPE_NOT_REGOGNISED			(1 << 10)
+#define  RXCHECKSUM_ERROR				(1 << 9)
+#define  RXECC_MULTIBIT_ERROR				(1 << 8)
+#define  RXECC_SINGLE_BIT_ERROR				(1 << 7)
+#define  RXFALSE_CONTROL_ERROR				(1 << 6)
+#define  RXHS_RECEIVE_TIMEOUT_ERROR			(1 << 5)
+#define  RX_LP_TX_SYNC_ERROR				(1 << 4)
+#define  RXEXCAPE_MODE_ENTRY_ERROR			(1 << 3)
+#define  RXEOT_SYNC_ERROR				(1 << 2)
+#define  RXSOT_SYNC_ERROR				(1 << 1)
+#define  RXSOT_ERROR					(1 << 0)
+
+#define _MIPIA_DSI_FUNC_PRG			(VLV_DISPLAY_BASE + 0xb00c)
+#define _MIPIB_DSI_FUNC_PRG			(VLV_DISPLAY_BASE + 0xb80c)
+#define MIPI_DSI_FUNC_PRG(pipe)		_PIPE(pipe, _MIPIA_DSI_FUNC_PRG, _MIPIB_DSI_FUNC_PRG)
+#define  CMD_MODE_DATA_WIDTH_MASK			(7 << 13)
+#define  CMD_MODE_NOT_SUPPORTED				(0 << 13)
+#define  CMD_MODE_DATA_WIDTH_16_BIT			(1 << 13)
+#define  CMD_MODE_DATA_WIDTH_9_BIT			(2 << 13)
+#define  CMD_MODE_DATA_WIDTH_8_BIT			(3 << 13)
+#define  CMD_MODE_DATA_WIDTH_OPTION1			(4 << 13)
+#define  CMD_MODE_DATA_WIDTH_OPTION2			(5 << 13)
+#define  VID_MODE_FORMAT_MASK				(0xf << 7)
+#define  VID_MODE_NOT_SUPPORTED				(0 << 7)
+#define  VID_MODE_FORMAT_RGB565				(1 << 7)
+#define  VID_MODE_FORMAT_RGB666				(2 << 7)
+#define  VID_MODE_FORMAT_RGB666_LOOSE			(3 << 7)
+#define  VID_MODE_FORMAT_RGB888				(4 << 7)
+#define  CMD_MODE_CHANNEL_NUMBER_SHIFT			5
+#define  CMD_MODE_CHANNEL_NUMBER_MASK			(3 << 5)
+#define  VID_MODE_CHANNEL_NUMBER_SHIFT			3
+#define  VID_MODE_CHANNEL_NUMBER_MASK			(3 << 3)
+#define  DATA_LANES_PRG_REG_SHIFT			0
+#define  DATA_LANES_PRG_REG_MASK			(7 << 0)
+
+#define _MIPIA_HS_TX_TIMEOUT			(VLV_DISPLAY_BASE + 0xb010)
+#define _MIPIB_HS_TX_TIMEOUT			(VLV_DISPLAY_BASE + 0xb810)
+#define MIPI_HS_TX_TIMEOUT(pipe)	_PIPE(pipe, _MIPIA_HS_TX_TIMEOUT, _MIPIB_HS_TX_TIMEOUT)
+#define  HIGH_SPEED_TX_TIMEOUT_COUNTER_MASK		0xffffff
+
+#define _MIPIA_LP_RX_TIMEOUT			(VLV_DISPLAY_BASE + 0xb014)
+#define _MIPIB_LP_RX_TIMEOUT			(VLV_DISPLAY_BASE + 0xb814)
+#define MIPI_LP_RX_TIMEOUT(pipe)	_PIPE(pipe, _MIPIA_LP_RX_TIMEOUT, _MIPIB_LP_RX_TIMEOUT)
+#define  LOW_POWER_RX_TIMEOUT_COUNTER_MASK		0xffffff
+
+#define _MIPIA_TURN_AROUND_TIMEOUT		(VLV_DISPLAY_BASE + 0xb018)
+#define _MIPIB_TURN_AROUND_TIMEOUT		(VLV_DISPLAY_BASE + 0xb818)
+#define MIPI_TURN_AROUND_TIMEOUT(pipe)	_PIPE(pipe, _MIPIA_TURN_AROUND_TIMEOUT, _MIPIB_TURN_AROUND_TIMEOUT)
+#define  TURN_AROUND_TIMEOUT_MASK			0x3f
+
+#define _MIPIA_DEVICE_RESET_TIMER		(VLV_DISPLAY_BASE + 0xb01c)
+#define _MIPIB_DEVICE_RESET_TIMER		(VLV_DISPLAY_BASE + 0xb81c)
+#define MIPI_DEVICE_RESET_TIMER(pipe)	_PIPE(pipe, _MIPIA_DEVICE_RESET_TIMER, _MIPIB_DEVICE_RESET_TIMER)
+#define  DEVICE_RESET_TIMER_MASK			0xffff
+
+#define _MIPIA_DPI_RESOLUTION			(VLV_DISPLAY_BASE + 0xb020)

drivers/gpu/drm/i915/i915_reg.h line 5262

Quoted 10 lines

drivers/gpu/drm/i915/i915_reg.h +10 -0

+#define _MIPIB_DPI_RESOLUTION			(VLV_DISPLAY_BASE + 0xb820)
+#define MIPI_DPI_RESOLUTION(pipe)	_PIPE(pipe, _MIPIA_DPI_RESOLUTION, _MIPIB_DPI_RESOLUTION)
+#define  VERTICAL_ADDRESS_SHIFT				16
+#define  VERTICAL_ADDRESS_MASK				(0xffff << 16)
+#define  HORIZONTAL_ADDRESS_SHIFT			0
+#define  HORIZONTAL_ADDRESS_MASK			0xffff
+
+/* XXX */
+#define _MIPIA_DBI_FIFO_THROTTLE		(VLV_DISPLAY_BASE + 0xb024)
+#define _MIPIB_DBI_FIFO_THROTTLE		(VLV_DISPLAY_BASE + 0xb824)

Is the XXX about the register name here? Spec lists it as MIPIA_DBI_RESOLUTION, which doesn't make much sense based on the contents.

Quoted 33 lines

drivers/gpu/drm/i915/i915_reg.h +33 -0

+#define MIPI_DBI_FIFO_THROTTLE(pipe)	_PIPE(pipe, _MIPIA_DBI_FIFO_THROTTLE, _MIPIB_DBI_FIFO_THROTTLE)
+#define  DBI_FIFO_EMPTY_HALF				(0 << 0)
+#define  DBI_FIFO_EMPTY_QUARTER				(1 << 0)
+#define  DBI_FIFO_EMPTY_7_LOCATIONS			(2 << 0)
+
+/* regs below are bits 15:0 */
+#define _MIPIA_HSYNC_PADDING_COUNT		(VLV_DISPLAY_BASE + 0xb028)
+#define _MIPIB_HSYNC_PADDING_COUNT		(VLV_DISPLAY_BASE + 0xb828)
+#define MIPI_HSYNC_PADDING_COUNT(pipe)	_PIPE(pipe, _MIPIA_HSYNC_PADDING_COUNT, _MIPIB_HSYNC_PADDING_COUNT)
+
+#define _MIPIA_HBP_COUNT			(VLV_DISPLAY_BASE + 0xb02c)
+#define _MIPIB_HBP_COUNT			(VLV_DISPLAY_BASE + 0xb82c)
+#define MIPI_HBP_COUNT(pipe)		_PIPE(pipe, _MIPIA_HBP_COUNT, _MIPIB_HBP_COUNT)
+
+#define _MIPIA_HFP_COUNT			(VLV_DISPLAY_BASE + 0xb030)
+#define _MIPIB_HFP_COUNT			(VLV_DISPLAY_BASE + 0xb830)
+#define MIPI_HFP_COUNT(pipe)		_PIPE(pipe, _MIPIA_HFP_COUNT, _MIPIB_HFP_COUNT)
+
+#define _MIPIA_HACTIVE_AREA_COUNT		(VLV_DISPLAY_BASE + 0xb034)
+#define _MIPIB_HACTIVE_AREA_COUNT		(VLV_DISPLAY_BASE + 0xb834)
+#define MIPI_HACTIVE_AREA_COUNT(pipe)	_PIPE(pipe, _MIPIA_HACTIVE_AREA_COUNT, _MIPIB_HACTIVE_AREA_COUNT)
+
+#define _MIPIA_VSYNC_PADDING_COUNT		(VLV_DISPLAY_BASE + 0xb038)
+#define _MIPIB_VSYNC_PADDING_COUNT		(VLV_DISPLAY_BASE + 0xb838)
+#define MIPI_VSYNC_PADDING_COUNT(pipe)	_PIPE(pipe, _MIPIA_VSYNC_PADDING_COUNT, _MIPIB_VSYNC_PADDING_COUNT)
+
+#define _MIPIA_VBP_COUNT			(VLV_DISPLAY_BASE + 0xb03c)
+#define _MIPIB_VBP_COUNT			(VLV_DISPLAY_BASE + 0xb83c)
+#define MIPI_VBP_COUNT(pipe)		_PIPE(pipe, _MIPIA_VBP_COUNT, _MIPIB_VBP_COUNT)
+
+#define _MIPIA_VFP_COUNT			(VLV_DISPLAY_BASE + 0xb040)
+#define _MIPIB_VFP_COUNT			(VLV_DISPLAY_BASE + 0xb840)
+#define MIPI_VFP_COUNT(pipe)		_PIPE(pipe, _MIPIA_VFP_COUNT, _MIPIB_VFP_COUNT)

drivers/gpu/drm/i915/i915_reg.h line 5305

Quoted 10 lines

drivers/gpu/drm/i915/i915_reg.h +10 -0

+
+#define _MIPIA_HIGH_LOW_SWITCH_COUNT		(VLV_DISPLAY_BASE + 0xb044)
+#define _MIPIB_HIGH_LOW_SWITCH_COUNT		(VLV_DISPLAY_BASE + 0xb844)
+#define MIPI_HIGH_LOW_SWITCH_COUNT(pipe)	_PIPE(pipe, _MIPIA_HIGH_LOW_SWITCH_COUNT, _MIPIB_HIGH_LOW_SWITCH_COUNT)
+/* regs above are bits 15:0 */
+
+#define _MIPIA_DPI_CONTROL			(VLV_DISPLAY_BASE + 0xb048)
+#define _MIPIB_DPI_CONTROL			(VLV_DISPLAY_BASE + 0xb848)
+#define MIPI_DPI_CONTROL(pipe)		_PIPE(pipe, _MIPIA_DPI_CONTROL, _MIPIB_DPI_CONTROL)
+#define  DPI_HS_MODE					(1 << 6)

Spec says 0=HS 1=LP, so this seems a bit backwards.

Quoted 218 lines

drivers/gpu/drm/i915/i915_reg.h +210 -0

+#define  BACKLIGHT_OFF					(1 << 5)
+#define  BACKLIGHT_ON					(1 << 4)
+#define  COLOR_MODE_OFF					(1 << 3)
+#define  COLOR_MODE_ON					(1 << 2)
+#define  TURN_ON					(1 << 1)
+#define  SHUTDOWN					(1 << 0)
+
+#define _MIPIA_DPI_DATA				(VLV_DISPLAY_BASE + 0xb04c)
+#define _MIPIB_DPI_DATA				(VLV_DISPLAY_BASE + 0xb84c)
+#define MIPI_DPI_DATA(pipe)		_PIPE(pipe, _MIPIA_DPI_DATA, _MIPIB_DPI_DATA)
+#define  COMMAND_BYTE_SHIFT				0
+#define  COMMAND_BYTE_MASK				(0x3f << 0)
+
+#define _MIPIA_INIT_COUNT			(VLV_DISPLAY_BASE + 0xb050)
+#define _MIPIB_INIT_COUNT			(VLV_DISPLAY_BASE + 0xb850)
+#define MIPI_INIT_COUNT(pipe)		_PIPE(pipe, _MIPIA_INIT_COUNT, _MIPIB_INIT_COUNT)
+#define  MASTER_INIT_TIMER_SHIFT			0
+#define  MASTER_INIT_TIMER_MASK				(0xffff << 0)
+
+#define _MIPIA_MAX_RETURN_PKT_SIZE		(VLV_DISPLAY_BASE + 0xb054)
+#define _MIPIB_MAX_RETURN_PKT_SIZE		(VLV_DISPLAY_BASE + 0xb854)
+#define MIPI_MAX_RETURN_PKT_SIZE(pipe)	_PIPE(pipe, _MIPIA_MAX_RETURN_PKT_SIZE, _MIPIB_MAX_RETURN_PKT_SIZE)
+#define  MAX_RETURN_PKT_SIZE_SHIFT			0
+#define  MAX_RETURN_PKT_SIZE_MASK			(0x3ff << 0)
+
+#define _MIPIA_VIDEO_MODE_FORMAT		(VLV_DISPLAY_BASE + 0xb058)
+#define _MIPIB_VIDEO_MODE_FORMAT		(VLV_DISPLAY_BASE + 0xb858)
+#define MIPI_VIDEO_MODE_FORMAT(pipe)	_PIPE(pipe, _MIPIA_VIDEO_MODE_FORMAT, _MIPIB_VIDEO_MODE_FORMAT)
+#define  RANDOM_DPI_DISPLAY_RESOLUTION			(1 << 4)
+#define  DISABLE_VIDEO_BTA				(1 << 3)
+#define  IP_TG_CONFIG					(1 << 2)
+#define  VIDEO_MODE_NON_BURST_WITH_SYNC_PULSE		(1 << 0)
+#define  VIDEO_MODE_NON_BURST_WITH_SYNC_EVENTS		(2 << 0)
+#define  VIDEO_MODE_BURST				(3 << 0)
+
+#define _MIPIA_EOT_DISABLE			(VLV_DISPLAY_BASE + 0xb05c)
+#define _MIPIB_EOT_DISABLE			(VLV_DISPLAY_BASE + 0xb85c)
+#define MIPI_EOT_DISABLE(pipe)		_PIPE(pipe, _MIPIA_EOT_DISABLE, _MIPIB_EOT_DISABLE)
+#define  LP_RX_TIMEOUT_ERROR_RECOVERY_DISABLE		(1 << 7)
+#define  HS_RX_TIMEOUT_ERROR_RECOVERY_DISABLE		(1 << 6)
+#define  LOW_CONTENTION_RECOVERY_DISABLE		(1 << 5)
+#define  HIGH_CONTENTION_RECOVERY_DISABLE		(1 << 4)
+#define  TXDSI_TYPE_NOT_RECOGNISED_ERROR_RECOVERY_DISABLE (1 << 3)
+#define  TXECC_MULTIBIT_ERROR_RECOVERY_DISABLE		(1 << 2)
+#define  CLOCKSTOP					(1 << 1)
+#define  EOT_DISABLE					(1 << 0)
+
+#define _MIPIA_LP_BYTECLK			(VLV_DISPLAY_BASE + 0xb060)
+#define _MIPIB_LP_BYTECLK			(VLV_DISPLAY_BASE + 0xb860)
+#define MIPI_LP_BYTECLK(pipe)		_PIPE(pipe, _MIPIA_LP_BYTECLK, _MIPIB_LP_BYTECLK)
+#define  LP_BYTECLK_SHIFT				0
+#define  LP_BYTECLK_MASK				(0xffff << 0)
+
+/* bits 31:0 */
+#define _MIPIA_LP_GEN_DATA			(VLV_DISPLAY_BASE + 0xb064)
+#define _MIPIB_LP_GEN_DATA			(VLV_DISPLAY_BASE + 0xb864)
+#define MIPI_LP_GEN_DATA(pipe)		_PIPE(pipe, _MIPIA_LP_GEN_DATA, _MIPIB_LP_GEN_DATA)
+
+/* bits 31:0 */
+#define _MIPIA_HS_GEN_DATA			(VLV_DISPLAY_BASE + 0xb068)
+#define _MIPIB_HS_GEN_DATA			(VLV_DISPLAY_BASE + 0xb868)
+#define MIPI_HS_GEN_DATA(pipe)		_PIPE(pipe, _MIPIA_HS_GEN_DATA, _MIPIB_HS_GEN_DATA)
+
+#define _MIPIA_LP_GEN_CTRL			(VLV_DISPLAY_BASE + 0xb06c)
+#define _MIPIB_LP_GEN_CTRL			(VLV_DISPLAY_BASE + 0xb86c)
+#define MIPI_LP_GEN_CTRL(pipe)		_PIPE(pipe, _MIPIA_LP_GEN_CTRL, _MIPIB_LP_GEN_CTRL)
+#define _MIPIA_HS_GEN_CTRL			(VLV_DISPLAY_BASE + 0xb070)
+#define _MIPIB_HS_GEN_CTRL			(VLV_DISPLAY_BASE + 0xb870)
+#define MIPI_HS_GEN_CTRL(pipe)		_PIPE(pipe, _MIPIA_HS_GEN_CTRL, _MIPIB_HS_GEN_CTRL)
+#define  LONG_PACKET_WORD_COUNT_SHIFT			8
+#define  LONG_PACKET_WORD_COUNT_MASK			(0xffff << 8)
+#define  SHORT_PACKET_PARAM_SHIFT			8
+#define  SHORT_PACKET_PARAM_MASK			(0xffff << 8)
+#define  VIRTUAL_CHANNEL_SHIFT				6
+#define  VIRTUAL_CHANNEL_MASK				(3 << 6)
+#define  DATA_TYPE_SHIFT				0
+#define  DATA_TYPE_MASK					(3f << 0)
+/* data type values, see include/video/mipi_display.h */
+
+#define _MIPIA_GEN_FIFO_STAT			(VLV_DISPLAY_BASE + 0xb074)
+#define _MIPIB_GEN_FIFO_STAT			(VLV_DISPLAY_BASE + 0xb874)
+#define MIPI_GEN_FIFO_STAT(pipe)	_PIPE(pipe, _MIPIA_GEN_FIFO_STAT, _MIPIB_GEN_FIFO_STAT)
+#define  DPI_FIFO_EMPTY					(1 << 28)
+#define  DBI_FIFO_EMPTY					(1 << 27)
+#define  LP_CTRL_FIFO_EMPTY				(1 << 26)
+#define  LP_CTRL_FIFO_HALF_EMPTY			(1 << 25)
+#define  LP_CTRL_FIFO_FULL				(1 << 24)
+#define  HS_CTRL_FIFO_EMPTY				(1 << 18)
+#define  HS_CTRL_FIFO_HALF_EMPTY			(1 << 17)
+#define  HS_CTRL_FIFO_FULL				(1 << 16)
+#define  LP_DATA_FIFO_EMPTY				(1 << 10)
+#define  LP_DATA_FIFO_HALF_EMPTY			(1 << 9)
+#define  LP_DATA_FIFO_FULL				(1 << 8)
+#define  HS_DATA_FIFO_EMPTY				(1 << 2)
+#define  HS_DATA_FIFO_HALF_EMPTY			(1 << 1)
+#define  HS_DATA_FIFO_FULL				(1 << 0)
+
+#define _MIPIA_HS_LS_DBI_ENABLE			(VLV_DISPLAY_BASE + 0xb078)
+#define _MIPIB_HS_LS_DBI_ENABLE			(VLV_DISPLAY_BASE + 0xb878)
+#define MIPI_HS_LP_DBI_ENABLE(pipe)	_PIPE(pipe, _MIPIA_HS_LS_DBI_ENABLE, _MIPIB_HS_LS_DBI_ENABLE)
+#define  DBI_HS_LP_MODE_MASK				(1 << 0)
+#define  DBI_LP_MODE					(1 << 0)
+#define  DBI_HS_MODE					(0 << 0)
+
+#define _MIPIA_DPHY_PARAM			(VLV_DISPLAY_BASE + 0xb080)
+#define _MIPIB_DPHY_PARAM			(VLV_DISPLAY_BASE + 0xb880)
+#define MIPI_DPHY_PARAM(pipe)		_PIPE(pipe, _MIPIA_DPHY_PARAM, _MIPIB_DPHY_PARAM)
+#define  EXIT_ZERO_COUNT_SHIFT				24
+#define  EXIT_ZERO_COUNT_MASK				(0x3f << 24)
+#define  TRAIL_COUNT_SHIFT				16
+#define  TRAIL_COUNT_MASK				(0x1f << 16)
+#define  CLK_ZERO_COUNT_SHIFT				8
+#define  CLK_ZERO_COUNT_MASK				(0xff << 8)
+#define  PREPARE_COUNT_SHIFT				0
+#define  PREPARE_COUNT_MASK				(0x3f << 0)
+
+/* bits 31:0 */
+#define _MIPIA_DBI_BW_CTRL			(VLV_DISPLAY_BASE + 0xb084)
+#define _MIPIB_DBI_BW_CTRL			(VLV_DISPLAY_BASE + 0xb884)
+#define MIPI_DBI_BW_CTRL(pipe)		_PIPE(pipe, _MIPIA_DBI_BW_CTRL, _MIPIB_DBI_BW_CTRL)
+
+#define _MIPIA_CLK_LANE_SWITCH_TIME_CNT		(VLV_DISPLAY_BASE + 0xb088)
+#define _MIPIB_CLK_LANE_SWITCH_TIME_CNT		(VLV_DISPLAY_BASE + 0xb888)
+#define MIPI_CLK_LANE_SWITCH_TIME_CNT(pipe)	_PIPE(pipe, _MIPIA_CLK_LANE_SWITCH_TIME_CNT, _MIPIB_CLK_LANE_SWITCH_TIME_CNT)
+#define  LP_HS_SSW_CNT_SHIFT				16
+#define  LP_HS_SSW_CNT_MASK				(0xffff << 16)
+#define  HS_LP_PWR_SW_CNT_SHIFT				0
+#define  HS_LP_PWR_SW_CNT_MASK				(0xffff << 0)
+
+#define _MIPIA_STOP_STATE_STALL			(VLV_DISPLAY_BASE + 0xb08c)
+#define _MIPIB_STOP_STATE_STALL			(VLV_DISPLAY_BASE + 0xb88c)
+#define MIPI_STOP_STATE_STALL(pipe)	_PIPE(pipe, _MIPIA_STOP_STATE_STALL, _MIPIB_STOP_STATE_STALL)
+#define  STOP_STATE_STALL_COUNTER_SHIFT			0
+#define  STOP_STATE_STALL_COUNTER_MASK			(0xff << 0)
+
+#define _MIPIA_INTR_STAT_REG_1			(VLV_DISPLAY_BASE + 0xb090)
+#define _MIPIB_INTR_STAT_REG_1			(VLV_DISPLAY_BASE + 0xb890)
+#define MIPI_INTR_STAT_REG_1(pipe)	_PIPE(pipe, _MIPIA_INTR_STAT_REG_1, _MIPIB_INTR_STAT_REG_1)
+#define _MIPIA_INTR_EN_REG_1			(VLV_DISPLAY_BASE + 0xb094)
+#define _MIPIB_INTR_EN_REG_1			(VLV_DISPLAY_BASE + 0xb894)
+#define MIPI_INTR_EN_REG_1(pipe)	_PIPE(pipe, _MIPIA_INTR_EN_REG_1, _MIPIB_INTR_EN_REG_1)
+#define  RX_CONTENTION_DETECTED				(1 << 0)
+
+/* XXX: only pipe A ?!? */
+#define MIPIA_DBI_TYPEC_CTRL			(VLV_DISPLAY_BASE + 0xb100)
+#define  DBI_TYPEC_ENABLE				(1 << 31)
+#define  DBI_TYPEC_WIP					(1 << 30)
+#define  DBI_TYPEC_OPTION_SHIFT				28
+#define  DBI_TYPEC_OPTION_MASK				(3 << 28)
+#define  DBI_TYPEC_FREQ_SHIFT				24
+#define  DBI_TYPEC_FREQ_MASK				(0xf << 24)
+#define  DBI_TYPEC_OVERRIDE				(1 << 8)
+#define  DBI_TYPEC_OVERRIDE_COUNTER_SHIFT		0
+#define  DBI_TYPEC_OVERRIDE_COUNTER_MASK		(0xff << 0)
+
+
+/* MIPI adapter registers */
+
+#define _MIPIA_CTRL				(VLV_DISPLAY_BASE + 0xb104)
+#define _MIPIB_CTRL				(VLV_DISPLAY_BASE + 0xb904)
+#define MIPI_CTRL(pipe)			_PIPE(pipe, _MIPIA_CTRL, _MIPIB_CTRL)
+#define  ESCAPE_CLOCK_DIVIDER_SHIFT			5 /* A only */
+#define  ESCAPE_CLOCK_DIVIDER_MASK			(3 << 5)
+#define  ESCAPE_CLOCK_DIVIDER_1				(0 << 5)
+#define  ESCAPE_CLOCK_DIVIDER_2				(1 << 5)
+#define  ESCAPE_CLOCK_DIVIDER_4				(2 << 5)
+#define  READ_REQUEST_PRIORITY_SHIFT			3
+#define  READ_REQUEST_PRIORITY_MASK			(3 << 3)
+#define  READ_REQUEST_PRIORITY_LOW			(0 << 3)
+#define  READ_REQUEST_PRIORITY_HIGH			(3 << 3)
+#define  RGB_FLIP_TO_BGR				(1 << 2)
+
+#define _MIPIA_DATA_ADDRESS			(VLV_DISPLAY_BASE + 0xb108)
+#define _MIPIB_DATA_ADDRESS			(VLV_DISPLAY_BASE + 0xb908)
+#define MIPI_DATA_ADDRESS(pipe)		_PIPE(pipe, _MIPIA_DATA_ADDRESS, _MIPIB_DATA_ADDRESS)
+#define  DATA_MEM_ADDRESS_SHIFT				5
+#define  DATA_MEM_ADDRESS_MASK				(0x7ffffff << 5)
+#define  DATA_VALID					(1 << 0)
+
+#define _MIPIA_DATA_LENGTH			(VLV_DISPLAY_BASE + 0xb10c)
+#define _MIPIB_DATA_LENGTH			(VLV_DISPLAY_BASE + 0xb90c)
+#define MIPI_DATA_LENGTH(pipe)		_PIPE(pipe, _MIPIA_DATA_LENGTH, _MIPIB_DATA_LENGTH)
+#define  DATA_LENGTH_SHIFT				0
+#define  DATA_LENGTH_MASK				(0xfffff << 0)
+
+#define _MIPIA_COMMAND_ADDRESS			(VLV_DISPLAY_BASE + 0xb110)
+#define _MIPIB_COMMAND_ADDRESS			(VLV_DISPLAY_BASE + 0xb910)
+#define MIPI_COMMAND_ADDRESS(pipe)	_PIPE(pipe, _MIPIA_COMMAND_ADDRESS, _MIPIB_COMMAND_ADDRESS)
+#define  COMMAND_MEM_ADDRESS_SHIFT			5
+#define  COMMAND_MEM_ADDRESS_MASK			(0x7ffffff << 5)
+#define  AUTO_PWG_ENABLE				(1 << 2)
+#define  MEMORY_WRITE_DATA_FROM_PIPE_RENDERING		(1 << 1)
+#define  COMMAND_VALID					(1 << 0)
+
+#define _MIPIA_COMMAND_LENGTH			(VLV_DISPLAY_BASE + 0xb114)
+#define _MIPIB_COMMAND_LENGTH			(VLV_DISPLAY_BASE + 0xb914)
+#define MIPI_COMMAND_LENGTH(pipe)	_PIPE(pipe, _MIPIA_COMMAND_LENGTH, _MIPIB_COMMAND_LENGTH)
+#define  COMMAND_LENGTH_SHIFT(n)			(8 * (n)) /* n: 0...3 */
+#define  COMMAND_LENGTH_MASK(n)				(0xff << (8 * (n)))
+
+#define _MIPIA_READ_DATA_RETURN0		(VLV_DISPLAY_BASE + 0xb118)
+#define _MIPIB_READ_DATA_RETURN0		(VLV_DISPLAY_BASE + 0xb918)
+#define MIPI_READ_DATA_RETURN(pipe, n) \
+	(_PIPE(pipe, _MIPIA_READ_DATA_RETURN0, _MIPIB_READ_DATA_RETURN0) + 4 * (n)) /* n: 0...7 */
+
+#define _MIPIA_READ_DATA_VALID			(VLV_DISPLAY_BASE + 0xb138)
+#define _MIPIB_READ_DATA_VALID			(VLV_DISPLAY_BASE + 0xb938)
+#define MIPI_READ_DATA_VALID(pipe)	_PIPE(pipe, _MIPIA_READ_DATA_VALID, _MIPIB_READ_DATA_VALID)
+#define  READ_DATA_VALID(n)				(1 << (n))
+
 #endif /* _I915_REG_H_ */

Signature · 6 lines

1.7.9.5

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

Signature · 2 lines

Ville Syrjälä
Intel OTC

Jani Nikula

author

2013-08-15 08:01 UTC #6 lore raw

Re: [PATCH 04/14] drm/i915: add MIPI DSI register definitions

Quoted 16 lines · Ville Syrjälä

Quoted 15 lines · Jani Nikula

Add definitions for VLV MIPI DSI registers.

Signed-off-by Jani Nikula <[email protected]>

---
 drivers/gpu/drm/i915/i915_reg.h |  409 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 409 insertions(+)

drivers/gpu/drm/i915/i915_reg.h +0 -0

index aced53a..32e32b6 100644
@@ -5104,4 +5104,413 @@
 #define PIPE_CSC_POSTOFF_ME(pipe) _PIPE(pipe, _PIPE_A_CSC_POSTOFF_ME, _PIPE_B_CSC_POSTOFF_ME)
 #define PIPE_CSC_POSTOFF_LO(pipe) _PIPE(pipe, _PIPE_A_CSC_POSTOFF_LO, _PIPE_B_CSC_POSTOFF_LO)

Quoted 14 lines

drivers/gpu/drm/i915/i915_reg.h line 5118

Quoted 12 lines

drivers/gpu/drm/i915/i915_reg.h +12 -0

+/* VLV MIPI registers */
+
+/* XXX: This register seems very messy. MIPIB has only enable and delay. */
+#define _MIPIA_PORT_CTRL			(VLV_DISPLAY_BASE + 0x61190)
+#define _MIPIB_PORT_CTRL			(VLV_DISPLAY_BASE + 0x61700)
+#define MIPI_PORT_CTRL(pipe)		_PIPE(pipe, _MIPIA_PORT_CTRL, _MIPIB_PORT_CTRL)
+#define  DPI_ENABLE					(1 << 31) /* A + B */
+#define  MIPIA_MIPI4DPHY_DELAY_COUNT_SHIFT		27
+#define  MIPIA_MIPI4DPHY_DELAY_COUNT_MASK		(0xf << 27)
+#define  DUAL_LINK_MODE_MASK				(1 << 26)
+#define  DUAL_LINK_MODE_FRONT_BACK			(0 << 26)
+#define  DUAL_LINK_MODE_PIXEL_ALTERNATIVE		(1 << 26)

25 is "Dither Enable" according to my docs.

Fixed.

Quoted 5 lines

drivers/gpu/drm/i915/i915_reg.h line 5120
Quoted 2 lines
drivers/gpu/drm/i915/i915_reg.h +2 -0
+#define  FLOPPED_HSTX					(1 << 23)
+#define  DE_INVERT					(1 << 19) /* XXX */
One doc has DE_INVERT (and HS/VS invert and border enable bits), another has the FLISDSI stuff. I guess that's the XXX here.

Yeah, and as you can see the two are overlapping. I'd like to keep it like this as a memory aid.

Quoted 5 lines

drivers/gpu/drm/i915/i915_reg.h line 5123
Quoted 3 lines
drivers/gpu/drm/i915/i915_reg.h +3 -0
+#define  MIPIA_FLISDSI_DELAY_COUNT_SHIFT		18
+#define  MIPIA_FLISDSI_DELAY_COUNT_MASK			(0xf << 18)
+#define  AFE_LATCHOUT					(1 << 17)
16 is "LPOutput Hold"

Added.

Quoted 28 lines

drivers/gpu/drm/i915/i915_reg.h +28 -0

+#define  MIPIB_FLISDSI_DELAY_COUNT_HIGH_SHIFT		15
+#define  MIPIB_FLISDSI_DELAY_COUNT_HIGH_MASK		(1 << 15)
+#define  MIPIB_MIPI4DPHY_DELAY_COUNT_SHIFT		11
+#define  MIPIB_MIPI4DPHY_DELAY_COUNT_MASK		(0xf << 11)
+#define  CSB_SHIFT					9
+#define  CSB_MASK					(3 << 9)
+#define  CSB_20MHZ					(0 << 9)
+#define  CSB_10MHZ					(1 << 9)
+#define  CSB_40MHZ					(2 << 9)
+#define  BANDGAP_MASK					(1 << 8)
+#define  BANDGAP_PNW_CIRCUIT				(0 << 8)
+#define  BANDGAP_LNC_CIRCUIT				(1 << 8)
+#define  MIPIB_FLISDSI_DELAY_COUNT_LOW_SHIFT		5
+#define  MIPIB_FLISDSI_DELAY_COUNT_LOW_MASK		(7 << 5)
+#define  TEARING_EFFECT_DELAY				(1 << 4) /* A + B */
+#define  TEARING_EFFECT_SHIFT				2 /* A + B */
+#define  TEARING_EFFECT_MASK				(3 << 2)
+#define  TEARING_EFFECT_OFF				(0 << 2)
+#define  TEARING_EFFECT_DSI				(1 << 2)
+#define  TEARING_EFFECT_GPIO				(2 << 2)
+#define  LANE_CONFIGURATION_SHIFT			0
+#define  LANE_CONFIGURATION_MASK			(3 << 0)
+#define  LANE_CONFIGURATION_4LANE			(0 << 0)
+#define  LANE_CONFIGURATION_DUAL_LINK_A			(1 << 0)
+#define  LANE_CONFIGURATION_DUAL_LINK_B			(2 << 0)
+
+#define _MIPIA_TEARING_CTRL			(VLV_DISPLAY_BASE + 0x61194)
+#define _MIPIB_TEARING_CTRL			(VLV_DISPLAY_BASE + 0x61704)

Quoted 8 lines

drivers/gpu/drm/i915/i915_reg.h line 5157
Quoted 6 lines
drivers/gpu/drm/i915/i915_reg.h +6 -0
+#define MIPI_TEARING_CTRL(pipe)		_PIPE(pipe, _MIPIA_TEARING_CTRL, _MIPIB_TEARING_CTRL)
+#define  TEARING_EFFECT_DELAY_SHIFT			0
+#define  TEARING_EFFECT_DELAY_MASK			(0xffff << 0)
+
+/* XXX */
+#define _MIPIA_AUTOPWG				(VLV_DISPLAY_BASE + 0x611a0)
Is the XXX here because the spec says the contents are all "reserved"?

Yes; do you prefer adding that to the comment, or dropping the register altogether?

Quoted 4 lines

drivers/gpu/drm/i915/i915_reg.h +4 -0

+
+/* MIPI DSI Controller and D-PHY registers */
+
+#define _MIPIA_DEVICE_READY			(VLV_DISPLAY_BASE + 0xb000)

Quoted 8 lines

drivers/gpu/drm/i915/i915_reg.h line 5167

Quoted 6 lines

drivers/gpu/drm/i915/i915_reg.h +6 -0

+#define _MIPIB_DEVICE_READY			(VLV_DISPLAY_BASE + 0xb800)
+#define MIPI_DEVICE_READY(pipe)		_PIPE(pipe, _MIPIA_DEVICE_READY, _MIPIB_DEVICE_READY)
+#define  BUS_POSSESSION					(1 << 3) /* set to give bus to receiver */
+#define  ULPS_STATE_MASK				(3 << 1)
+#define  ULPS_STATE_ENTER				(2 << 1) /* XXX */
+#define  ULPS_STATE_EXIT				(1 << 1) /* XXX */

Maybe we should have the (0 << 1) "normal operation" listed here as well?

Added.

Quoted 91 lines

drivers/gpu/drm/i915/i915_reg.h +91 -0

+#define  DEVICE_READY					(1 << 0)
+
+#define _MIPIA_INTR_STAT			(VLV_DISPLAY_BASE + 0xb004)
+#define _MIPIB_INTR_STAT			(VLV_DISPLAY_BASE + 0xb804)
+#define MIPI_INTR_STAT(pipe)		_PIPE(pipe, _MIPIA_INTR_STAT, _MIPIB_INTR_STAT)
+#define _MIPIA_INTR_EN				(VLV_DISPLAY_BASE + 0xb008)
+#define _MIPIB_INTR_EN				(VLV_DISPLAY_BASE + 0xb808)
+#define MIPI_INTR_EN(pipe)		_PIPE(pipe, _MIPIA_INTR_EN, _MIPIB_INTR_EN)
+#define  TEARING_EFFECT					(1 << 31)
+#define  SPL_PKT_SENT_INTERRUPT				(1 << 30)
+#define  GEN_READ_DATA_AVAIL				(1 << 29)
+#define  LP_GENERIC_WR_FIFO_FULL			(1 << 28)
+#define  HS_GENERIC_WR_FIFO_FULL			(1 << 27)
+#define  RX_PROT_VIOLATION				(1 << 26)
+#define  RX_INVALID_TX_LENGTH				(1 << 25)
+#define  ACK_WITH_NO_ERROR				(1 << 24)
+#define  TURN_AROUND_ACK_TIMEOUT			(1 << 23)
+#define  LP_RX_TIMEOUT					(1 << 22)
+#define  HS_TX_TIMEOUT					(1 << 21)
+#define  DPI_FIFO_UNDERRUN				(1 << 20)
+#define  LOW_CONTENTION					(1 << 19)
+#define  HIGH_CONTENTION				(1 << 18)
+#define  TXDSI_VC_ID_INVALID				(1 << 17)
+#define  TXDSI_DATA_TYPE_NOT_RECOGNISED			(1 << 16)
+#define  TXCHECKSUM_ERROR				(1 << 15)
+#define  TXECC_MULTIBIT_ERROR				(1 << 14)
+#define  TXECC_SINGLE_BIT_ERROR				(1 << 13)
+#define  TXFALSE_CONTROL_ERROR				(1 << 12)
+#define  RXDSI_VC_ID_INVALID				(1 << 11)
+#define  RXDSI_DATA_TYPE_NOT_REGOGNISED			(1 << 10)
+#define  RXCHECKSUM_ERROR				(1 << 9)
+#define  RXECC_MULTIBIT_ERROR				(1 << 8)
+#define  RXECC_SINGLE_BIT_ERROR				(1 << 7)
+#define  RXFALSE_CONTROL_ERROR				(1 << 6)
+#define  RXHS_RECEIVE_TIMEOUT_ERROR			(1 << 5)
+#define  RX_LP_TX_SYNC_ERROR				(1 << 4)
+#define  RXEXCAPE_MODE_ENTRY_ERROR			(1 << 3)
+#define  RXEOT_SYNC_ERROR				(1 << 2)
+#define  RXSOT_SYNC_ERROR				(1 << 1)
+#define  RXSOT_ERROR					(1 << 0)
+
+#define _MIPIA_DSI_FUNC_PRG			(VLV_DISPLAY_BASE + 0xb00c)
+#define _MIPIB_DSI_FUNC_PRG			(VLV_DISPLAY_BASE + 0xb80c)
+#define MIPI_DSI_FUNC_PRG(pipe)		_PIPE(pipe, _MIPIA_DSI_FUNC_PRG, _MIPIB_DSI_FUNC_PRG)
+#define  CMD_MODE_DATA_WIDTH_MASK			(7 << 13)
+#define  CMD_MODE_NOT_SUPPORTED				(0 << 13)
+#define  CMD_MODE_DATA_WIDTH_16_BIT			(1 << 13)
+#define  CMD_MODE_DATA_WIDTH_9_BIT			(2 << 13)
+#define  CMD_MODE_DATA_WIDTH_8_BIT			(3 << 13)
+#define  CMD_MODE_DATA_WIDTH_OPTION1			(4 << 13)
+#define  CMD_MODE_DATA_WIDTH_OPTION2			(5 << 13)
+#define  VID_MODE_FORMAT_MASK				(0xf << 7)
+#define  VID_MODE_NOT_SUPPORTED				(0 << 7)
+#define  VID_MODE_FORMAT_RGB565				(1 << 7)
+#define  VID_MODE_FORMAT_RGB666				(2 << 7)
+#define  VID_MODE_FORMAT_RGB666_LOOSE			(3 << 7)
+#define  VID_MODE_FORMAT_RGB888				(4 << 7)
+#define  CMD_MODE_CHANNEL_NUMBER_SHIFT			5
+#define  CMD_MODE_CHANNEL_NUMBER_MASK			(3 << 5)
+#define  VID_MODE_CHANNEL_NUMBER_SHIFT			3
+#define  VID_MODE_CHANNEL_NUMBER_MASK			(3 << 3)
+#define  DATA_LANES_PRG_REG_SHIFT			0
+#define  DATA_LANES_PRG_REG_MASK			(7 << 0)
+
+#define _MIPIA_HS_TX_TIMEOUT			(VLV_DISPLAY_BASE + 0xb010)
+#define _MIPIB_HS_TX_TIMEOUT			(VLV_DISPLAY_BASE + 0xb810)
+#define MIPI_HS_TX_TIMEOUT(pipe)	_PIPE(pipe, _MIPIA_HS_TX_TIMEOUT, _MIPIB_HS_TX_TIMEOUT)
+#define  HIGH_SPEED_TX_TIMEOUT_COUNTER_MASK		0xffffff
+
+#define _MIPIA_LP_RX_TIMEOUT			(VLV_DISPLAY_BASE + 0xb014)
+#define _MIPIB_LP_RX_TIMEOUT			(VLV_DISPLAY_BASE + 0xb814)
+#define MIPI_LP_RX_TIMEOUT(pipe)	_PIPE(pipe, _MIPIA_LP_RX_TIMEOUT, _MIPIB_LP_RX_TIMEOUT)
+#define  LOW_POWER_RX_TIMEOUT_COUNTER_MASK		0xffffff
+
+#define _MIPIA_TURN_AROUND_TIMEOUT		(VLV_DISPLAY_BASE + 0xb018)
+#define _MIPIB_TURN_AROUND_TIMEOUT		(VLV_DISPLAY_BASE + 0xb818)
+#define MIPI_TURN_AROUND_TIMEOUT(pipe)	_PIPE(pipe, _MIPIA_TURN_AROUND_TIMEOUT, _MIPIB_TURN_AROUND_TIMEOUT)
+#define  TURN_AROUND_TIMEOUT_MASK			0x3f
+
+#define _MIPIA_DEVICE_RESET_TIMER		(VLV_DISPLAY_BASE + 0xb01c)
+#define _MIPIB_DEVICE_RESET_TIMER		(VLV_DISPLAY_BASE + 0xb81c)
+#define MIPI_DEVICE_RESET_TIMER(pipe)	_PIPE(pipe, _MIPIA_DEVICE_RESET_TIMER, _MIPIB_DEVICE_RESET_TIMER)
+#define  DEVICE_RESET_TIMER_MASK			0xffff
+
+#define _MIPIA_DPI_RESOLUTION			(VLV_DISPLAY_BASE + 0xb020)
+#define _MIPIB_DPI_RESOLUTION			(VLV_DISPLAY_BASE + 0xb820)
+#define MIPI_DPI_RESOLUTION(pipe)	_PIPE(pipe, _MIPIA_DPI_RESOLUTION, _MIPIB_DPI_RESOLUTION)
+#define  VERTICAL_ADDRESS_SHIFT				16
+#define  VERTICAL_ADDRESS_MASK				(0xffff << 16)
+#define  HORIZONTAL_ADDRESS_SHIFT			0
+#define  HORIZONTAL_ADDRESS_MASK			0xffff

Quoted 8 lines

drivers/gpu/drm/i915/i915_reg.h line 5262
Quoted 4 lines
drivers/gpu/drm/i915/i915_reg.h +4 -0
+
+/* XXX */
+#define _MIPIA_DBI_FIFO_THROTTLE		(VLV_DISPLAY_BASE + 0xb024)
+#define _MIPIB_DBI_FIFO_THROTTLE		(VLV_DISPLAY_BASE + 0xb824)
Is the XXX about the register name here? Spec lists it as MIPIA_DBI_RESOLUTION, which doesn't make much sense based on the contents.

Yes. I dropped the XXX comment. Another spec names the reg as DBI_FIFO_THROTTLE, which I'm inclided to trust as it matches the contents.

Quoted 37 lines

drivers/gpu/drm/i915/i915_reg.h +37 -0

+#define MIPI_DBI_FIFO_THROTTLE(pipe)	_PIPE(pipe, _MIPIA_DBI_FIFO_THROTTLE, _MIPIB_DBI_FIFO_THROTTLE)
+#define  DBI_FIFO_EMPTY_HALF				(0 << 0)
+#define  DBI_FIFO_EMPTY_QUARTER				(1 << 0)
+#define  DBI_FIFO_EMPTY_7_LOCATIONS			(2 << 0)
+
+/* regs below are bits 15:0 */
+#define _MIPIA_HSYNC_PADDING_COUNT		(VLV_DISPLAY_BASE + 0xb028)
+#define _MIPIB_HSYNC_PADDING_COUNT		(VLV_DISPLAY_BASE + 0xb828)
+#define MIPI_HSYNC_PADDING_COUNT(pipe)	_PIPE(pipe, _MIPIA_HSYNC_PADDING_COUNT, _MIPIB_HSYNC_PADDING_COUNT)
+
+#define _MIPIA_HBP_COUNT			(VLV_DISPLAY_BASE + 0xb02c)
+#define _MIPIB_HBP_COUNT			(VLV_DISPLAY_BASE + 0xb82c)
+#define MIPI_HBP_COUNT(pipe)		_PIPE(pipe, _MIPIA_HBP_COUNT, _MIPIB_HBP_COUNT)
+
+#define _MIPIA_HFP_COUNT			(VLV_DISPLAY_BASE + 0xb030)
+#define _MIPIB_HFP_COUNT			(VLV_DISPLAY_BASE + 0xb830)
+#define MIPI_HFP_COUNT(pipe)		_PIPE(pipe, _MIPIA_HFP_COUNT, _MIPIB_HFP_COUNT)
+
+#define _MIPIA_HACTIVE_AREA_COUNT		(VLV_DISPLAY_BASE + 0xb034)
+#define _MIPIB_HACTIVE_AREA_COUNT		(VLV_DISPLAY_BASE + 0xb834)
+#define MIPI_HACTIVE_AREA_COUNT(pipe)	_PIPE(pipe, _MIPIA_HACTIVE_AREA_COUNT, _MIPIB_HACTIVE_AREA_COUNT)
+
+#define _MIPIA_VSYNC_PADDING_COUNT		(VLV_DISPLAY_BASE + 0xb038)
+#define _MIPIB_VSYNC_PADDING_COUNT		(VLV_DISPLAY_BASE + 0xb838)
+#define MIPI_VSYNC_PADDING_COUNT(pipe)	_PIPE(pipe, _MIPIA_VSYNC_PADDING_COUNT, _MIPIB_VSYNC_PADDING_COUNT)
+
+#define _MIPIA_VBP_COUNT			(VLV_DISPLAY_BASE + 0xb03c)
+#define _MIPIB_VBP_COUNT			(VLV_DISPLAY_BASE + 0xb83c)
+#define MIPI_VBP_COUNT(pipe)		_PIPE(pipe, _MIPIA_VBP_COUNT, _MIPIB_VBP_COUNT)
+
+#define _MIPIA_VFP_COUNT			(VLV_DISPLAY_BASE + 0xb040)
+#define _MIPIB_VFP_COUNT			(VLV_DISPLAY_BASE + 0xb840)
+#define MIPI_VFP_COUNT(pipe)		_PIPE(pipe, _MIPIA_VFP_COUNT, _MIPIB_VFP_COUNT)
+
+#define _MIPIA_HIGH_LOW_SWITCH_COUNT		(VLV_DISPLAY_BASE + 0xb044)
+#define _MIPIB_HIGH_LOW_SWITCH_COUNT		(VLV_DISPLAY_BASE + 0xb844)
+#define MIPI_HIGH_LOW_SWITCH_COUNT(pipe)	_PIPE(pipe, _MIPIA_HIGH_LOW_SWITCH_COUNT, _MIPIB_HIGH_LOW_SWITCH_COUNT)

Quoted 8 lines

drivers/gpu/drm/i915/i915_reg.h line 5305
Quoted 6 lines
drivers/gpu/drm/i915/i915_reg.h +6 -0
+/* regs above are bits 15:0 */
+
+#define _MIPIA_DPI_CONTROL			(VLV_DISPLAY_BASE + 0xb048)
+#define _MIPIB_DPI_CONTROL			(VLV_DISPLAY_BASE + 0xb848)
+#define MIPI_DPI_CONTROL(pipe)		_PIPE(pipe, _MIPIA_DPI_CONTROL, _MIPIB_DPI_CONTROL)
+#define  DPI_HS_MODE					(1 << 6)
Spec says 0=HS 1=LP, so this seems a bit backwards.

*blush* Fixed.

Thanks for the review,
Jani.

Quoted 226 lines

Quoted 218 lines

drivers/gpu/drm/i915/i915_reg.h +210 -0

+#define  BACKLIGHT_OFF					(1 << 5)
+#define  BACKLIGHT_ON					(1 << 4)
+#define  COLOR_MODE_OFF					(1 << 3)
+#define  COLOR_MODE_ON					(1 << 2)
+#define  TURN_ON					(1 << 1)
+#define  SHUTDOWN					(1 << 0)
+
+#define _MIPIA_DPI_DATA				(VLV_DISPLAY_BASE + 0xb04c)
+#define _MIPIB_DPI_DATA				(VLV_DISPLAY_BASE + 0xb84c)
+#define MIPI_DPI_DATA(pipe)		_PIPE(pipe, _MIPIA_DPI_DATA, _MIPIB_DPI_DATA)
+#define  COMMAND_BYTE_SHIFT				0
+#define  COMMAND_BYTE_MASK				(0x3f << 0)
+
+#define _MIPIA_INIT_COUNT			(VLV_DISPLAY_BASE + 0xb050)
+#define _MIPIB_INIT_COUNT			(VLV_DISPLAY_BASE + 0xb850)
+#define MIPI_INIT_COUNT(pipe)		_PIPE(pipe, _MIPIA_INIT_COUNT, _MIPIB_INIT_COUNT)
+#define  MASTER_INIT_TIMER_SHIFT			0
+#define  MASTER_INIT_TIMER_MASK				(0xffff << 0)
+
+#define _MIPIA_MAX_RETURN_PKT_SIZE		(VLV_DISPLAY_BASE + 0xb054)
+#define _MIPIB_MAX_RETURN_PKT_SIZE		(VLV_DISPLAY_BASE + 0xb854)
+#define MIPI_MAX_RETURN_PKT_SIZE(pipe)	_PIPE(pipe, _MIPIA_MAX_RETURN_PKT_SIZE, _MIPIB_MAX_RETURN_PKT_SIZE)
+#define  MAX_RETURN_PKT_SIZE_SHIFT			0
+#define  MAX_RETURN_PKT_SIZE_MASK			(0x3ff << 0)
+
+#define _MIPIA_VIDEO_MODE_FORMAT		(VLV_DISPLAY_BASE + 0xb058)
+#define _MIPIB_VIDEO_MODE_FORMAT		(VLV_DISPLAY_BASE + 0xb858)
+#define MIPI_VIDEO_MODE_FORMAT(pipe)	_PIPE(pipe, _MIPIA_VIDEO_MODE_FORMAT, _MIPIB_VIDEO_MODE_FORMAT)
+#define  RANDOM_DPI_DISPLAY_RESOLUTION			(1 << 4)
+#define  DISABLE_VIDEO_BTA				(1 << 3)
+#define  IP_TG_CONFIG					(1 << 2)
+#define  VIDEO_MODE_NON_BURST_WITH_SYNC_PULSE		(1 << 0)
+#define  VIDEO_MODE_NON_BURST_WITH_SYNC_EVENTS		(2 << 0)
+#define  VIDEO_MODE_BURST				(3 << 0)
+
+#define _MIPIA_EOT_DISABLE			(VLV_DISPLAY_BASE + 0xb05c)
+#define _MIPIB_EOT_DISABLE			(VLV_DISPLAY_BASE + 0xb85c)
+#define MIPI_EOT_DISABLE(pipe)		_PIPE(pipe, _MIPIA_EOT_DISABLE, _MIPIB_EOT_DISABLE)
+#define  LP_RX_TIMEOUT_ERROR_RECOVERY_DISABLE		(1 << 7)
+#define  HS_RX_TIMEOUT_ERROR_RECOVERY_DISABLE		(1 << 6)
+#define  LOW_CONTENTION_RECOVERY_DISABLE		(1 << 5)
+#define  HIGH_CONTENTION_RECOVERY_DISABLE		(1 << 4)
+#define  TXDSI_TYPE_NOT_RECOGNISED_ERROR_RECOVERY_DISABLE (1 << 3)
+#define  TXECC_MULTIBIT_ERROR_RECOVERY_DISABLE		(1 << 2)
+#define  CLOCKSTOP					(1 << 1)
+#define  EOT_DISABLE					(1 << 0)
+
+#define _MIPIA_LP_BYTECLK			(VLV_DISPLAY_BASE + 0xb060)
+#define _MIPIB_LP_BYTECLK			(VLV_DISPLAY_BASE + 0xb860)
+#define MIPI_LP_BYTECLK(pipe)		_PIPE(pipe, _MIPIA_LP_BYTECLK, _MIPIB_LP_BYTECLK)
+#define  LP_BYTECLK_SHIFT				0
+#define  LP_BYTECLK_MASK				(0xffff << 0)
+
+/* bits 31:0 */
+#define _MIPIA_LP_GEN_DATA			(VLV_DISPLAY_BASE + 0xb064)
+#define _MIPIB_LP_GEN_DATA			(VLV_DISPLAY_BASE + 0xb864)
+#define MIPI_LP_GEN_DATA(pipe)		_PIPE(pipe, _MIPIA_LP_GEN_DATA, _MIPIB_LP_GEN_DATA)
+
+/* bits 31:0 */
+#define _MIPIA_HS_GEN_DATA			(VLV_DISPLAY_BASE + 0xb068)
+#define _MIPIB_HS_GEN_DATA			(VLV_DISPLAY_BASE + 0xb868)
+#define MIPI_HS_GEN_DATA(pipe)		_PIPE(pipe, _MIPIA_HS_GEN_DATA, _MIPIB_HS_GEN_DATA)
+
+#define _MIPIA_LP_GEN_CTRL			(VLV_DISPLAY_BASE + 0xb06c)
+#define _MIPIB_LP_GEN_CTRL			(VLV_DISPLAY_BASE + 0xb86c)
+#define MIPI_LP_GEN_CTRL(pipe)		_PIPE(pipe, _MIPIA_LP_GEN_CTRL, _MIPIB_LP_GEN_CTRL)
+#define _MIPIA_HS_GEN_CTRL			(VLV_DISPLAY_BASE + 0xb070)
+#define _MIPIB_HS_GEN_CTRL			(VLV_DISPLAY_BASE + 0xb870)
+#define MIPI_HS_GEN_CTRL(pipe)		_PIPE(pipe, _MIPIA_HS_GEN_CTRL, _MIPIB_HS_GEN_CTRL)
+#define  LONG_PACKET_WORD_COUNT_SHIFT			8
+#define  LONG_PACKET_WORD_COUNT_MASK			(0xffff << 8)
+#define  SHORT_PACKET_PARAM_SHIFT			8
+#define  SHORT_PACKET_PARAM_MASK			(0xffff << 8)
+#define  VIRTUAL_CHANNEL_SHIFT				6
+#define  VIRTUAL_CHANNEL_MASK				(3 << 6)
+#define  DATA_TYPE_SHIFT				0
+#define  DATA_TYPE_MASK					(3f << 0)
+/* data type values, see include/video/mipi_display.h */
+
+#define _MIPIA_GEN_FIFO_STAT			(VLV_DISPLAY_BASE + 0xb074)
+#define _MIPIB_GEN_FIFO_STAT			(VLV_DISPLAY_BASE + 0xb874)
+#define MIPI_GEN_FIFO_STAT(pipe)	_PIPE(pipe, _MIPIA_GEN_FIFO_STAT, _MIPIB_GEN_FIFO_STAT)
+#define  DPI_FIFO_EMPTY					(1 << 28)
+#define  DBI_FIFO_EMPTY					(1 << 27)
+#define  LP_CTRL_FIFO_EMPTY				(1 << 26)
+#define  LP_CTRL_FIFO_HALF_EMPTY			(1 << 25)
+#define  LP_CTRL_FIFO_FULL				(1 << 24)
+#define  HS_CTRL_FIFO_EMPTY				(1 << 18)
+#define  HS_CTRL_FIFO_HALF_EMPTY			(1 << 17)
+#define  HS_CTRL_FIFO_FULL				(1 << 16)
+#define  LP_DATA_FIFO_EMPTY				(1 << 10)
+#define  LP_DATA_FIFO_HALF_EMPTY			(1 << 9)
+#define  LP_DATA_FIFO_FULL				(1 << 8)
+#define  HS_DATA_FIFO_EMPTY				(1 << 2)
+#define  HS_DATA_FIFO_HALF_EMPTY			(1 << 1)
+#define  HS_DATA_FIFO_FULL				(1 << 0)
+
+#define _MIPIA_HS_LS_DBI_ENABLE			(VLV_DISPLAY_BASE + 0xb078)
+#define _MIPIB_HS_LS_DBI_ENABLE			(VLV_DISPLAY_BASE + 0xb878)
+#define MIPI_HS_LP_DBI_ENABLE(pipe)	_PIPE(pipe, _MIPIA_HS_LS_DBI_ENABLE, _MIPIB_HS_LS_DBI_ENABLE)
+#define  DBI_HS_LP_MODE_MASK				(1 << 0)
+#define  DBI_LP_MODE					(1 << 0)
+#define  DBI_HS_MODE					(0 << 0)
+
+#define _MIPIA_DPHY_PARAM			(VLV_DISPLAY_BASE + 0xb080)
+#define _MIPIB_DPHY_PARAM			(VLV_DISPLAY_BASE + 0xb880)
+#define MIPI_DPHY_PARAM(pipe)		_PIPE(pipe, _MIPIA_DPHY_PARAM, _MIPIB_DPHY_PARAM)
+#define  EXIT_ZERO_COUNT_SHIFT				24
+#define  EXIT_ZERO_COUNT_MASK				(0x3f << 24)
+#define  TRAIL_COUNT_SHIFT				16
+#define  TRAIL_COUNT_MASK				(0x1f << 16)
+#define  CLK_ZERO_COUNT_SHIFT				8
+#define  CLK_ZERO_COUNT_MASK				(0xff << 8)
+#define  PREPARE_COUNT_SHIFT				0
+#define  PREPARE_COUNT_MASK				(0x3f << 0)
+
+/* bits 31:0 */
+#define _MIPIA_DBI_BW_CTRL			(VLV_DISPLAY_BASE + 0xb084)
+#define _MIPIB_DBI_BW_CTRL			(VLV_DISPLAY_BASE + 0xb884)
+#define MIPI_DBI_BW_CTRL(pipe)		_PIPE(pipe, _MIPIA_DBI_BW_CTRL, _MIPIB_DBI_BW_CTRL)
+
+#define _MIPIA_CLK_LANE_SWITCH_TIME_CNT		(VLV_DISPLAY_BASE + 0xb088)
+#define _MIPIB_CLK_LANE_SWITCH_TIME_CNT		(VLV_DISPLAY_BASE + 0xb888)
+#define MIPI_CLK_LANE_SWITCH_TIME_CNT(pipe)	_PIPE(pipe, _MIPIA_CLK_LANE_SWITCH_TIME_CNT, _MIPIB_CLK_LANE_SWITCH_TIME_CNT)
+#define  LP_HS_SSW_CNT_SHIFT				16
+#define  LP_HS_SSW_CNT_MASK				(0xffff << 16)
+#define  HS_LP_PWR_SW_CNT_SHIFT				0
+#define  HS_LP_PWR_SW_CNT_MASK				(0xffff << 0)
+
+#define _MIPIA_STOP_STATE_STALL			(VLV_DISPLAY_BASE + 0xb08c)
+#define _MIPIB_STOP_STATE_STALL			(VLV_DISPLAY_BASE + 0xb88c)
+#define MIPI_STOP_STATE_STALL(pipe)	_PIPE(pipe, _MIPIA_STOP_STATE_STALL, _MIPIB_STOP_STATE_STALL)
+#define  STOP_STATE_STALL_COUNTER_SHIFT			0
+#define  STOP_STATE_STALL_COUNTER_MASK			(0xff << 0)
+
+#define _MIPIA_INTR_STAT_REG_1			(VLV_DISPLAY_BASE + 0xb090)
+#define _MIPIB_INTR_STAT_REG_1			(VLV_DISPLAY_BASE + 0xb890)
+#define MIPI_INTR_STAT_REG_1(pipe)	_PIPE(pipe, _MIPIA_INTR_STAT_REG_1, _MIPIB_INTR_STAT_REG_1)
+#define _MIPIA_INTR_EN_REG_1			(VLV_DISPLAY_BASE + 0xb094)
+#define _MIPIB_INTR_EN_REG_1			(VLV_DISPLAY_BASE + 0xb894)
+#define MIPI_INTR_EN_REG_1(pipe)	_PIPE(pipe, _MIPIA_INTR_EN_REG_1, _MIPIB_INTR_EN_REG_1)
+#define  RX_CONTENTION_DETECTED				(1 << 0)
+
+/* XXX: only pipe A ?!? */
+#define MIPIA_DBI_TYPEC_CTRL			(VLV_DISPLAY_BASE + 0xb100)
+#define  DBI_TYPEC_ENABLE				(1 << 31)
+#define  DBI_TYPEC_WIP					(1 << 30)
+#define  DBI_TYPEC_OPTION_SHIFT				28
+#define  DBI_TYPEC_OPTION_MASK				(3 << 28)
+#define  DBI_TYPEC_FREQ_SHIFT				24
+#define  DBI_TYPEC_FREQ_MASK				(0xf << 24)
+#define  DBI_TYPEC_OVERRIDE				(1 << 8)
+#define  DBI_TYPEC_OVERRIDE_COUNTER_SHIFT		0
+#define  DBI_TYPEC_OVERRIDE_COUNTER_MASK		(0xff << 0)
+
+
+/* MIPI adapter registers */
+
+#define _MIPIA_CTRL				(VLV_DISPLAY_BASE + 0xb104)
+#define _MIPIB_CTRL				(VLV_DISPLAY_BASE + 0xb904)
+#define MIPI_CTRL(pipe)			_PIPE(pipe, _MIPIA_CTRL, _MIPIB_CTRL)
+#define  ESCAPE_CLOCK_DIVIDER_SHIFT			5 /* A only */
+#define  ESCAPE_CLOCK_DIVIDER_MASK			(3 << 5)
+#define  ESCAPE_CLOCK_DIVIDER_1				(0 << 5)
+#define  ESCAPE_CLOCK_DIVIDER_2				(1 << 5)
+#define  ESCAPE_CLOCK_DIVIDER_4				(2 << 5)
+#define  READ_REQUEST_PRIORITY_SHIFT			3
+#define  READ_REQUEST_PRIORITY_MASK			(3 << 3)
+#define  READ_REQUEST_PRIORITY_LOW			(0 << 3)
+#define  READ_REQUEST_PRIORITY_HIGH			(3 << 3)
+#define  RGB_FLIP_TO_BGR				(1 << 2)
+
+#define _MIPIA_DATA_ADDRESS			(VLV_DISPLAY_BASE + 0xb108)
+#define _MIPIB_DATA_ADDRESS			(VLV_DISPLAY_BASE + 0xb908)
+#define MIPI_DATA_ADDRESS(pipe)		_PIPE(pipe, _MIPIA_DATA_ADDRESS, _MIPIB_DATA_ADDRESS)
+#define  DATA_MEM_ADDRESS_SHIFT				5
+#define  DATA_MEM_ADDRESS_MASK				(0x7ffffff << 5)
+#define  DATA_VALID					(1 << 0)
+
+#define _MIPIA_DATA_LENGTH			(VLV_DISPLAY_BASE + 0xb10c)
+#define _MIPIB_DATA_LENGTH			(VLV_DISPLAY_BASE + 0xb90c)
+#define MIPI_DATA_LENGTH(pipe)		_PIPE(pipe, _MIPIA_DATA_LENGTH, _MIPIB_DATA_LENGTH)
+#define  DATA_LENGTH_SHIFT				0
+#define  DATA_LENGTH_MASK				(0xfffff << 0)
+
+#define _MIPIA_COMMAND_ADDRESS			(VLV_DISPLAY_BASE + 0xb110)
+#define _MIPIB_COMMAND_ADDRESS			(VLV_DISPLAY_BASE + 0xb910)
+#define MIPI_COMMAND_ADDRESS(pipe)	_PIPE(pipe, _MIPIA_COMMAND_ADDRESS, _MIPIB_COMMAND_ADDRESS)
+#define  COMMAND_MEM_ADDRESS_SHIFT			5
+#define  COMMAND_MEM_ADDRESS_MASK			(0x7ffffff << 5)
+#define  AUTO_PWG_ENABLE				(1 << 2)
+#define  MEMORY_WRITE_DATA_FROM_PIPE_RENDERING		(1 << 1)
+#define  COMMAND_VALID					(1 << 0)
+
+#define _MIPIA_COMMAND_LENGTH			(VLV_DISPLAY_BASE + 0xb114)
+#define _MIPIB_COMMAND_LENGTH			(VLV_DISPLAY_BASE + 0xb914)
+#define MIPI_COMMAND_LENGTH(pipe)	_PIPE(pipe, _MIPIA_COMMAND_LENGTH, _MIPIB_COMMAND_LENGTH)
+#define  COMMAND_LENGTH_SHIFT(n)			(8 * (n)) /* n: 0...3 */
+#define  COMMAND_LENGTH_MASK(n)				(0xff << (8 * (n)))
+
+#define _MIPIA_READ_DATA_RETURN0		(VLV_DISPLAY_BASE + 0xb118)
+#define _MIPIB_READ_DATA_RETURN0		(VLV_DISPLAY_BASE + 0xb918)
+#define MIPI_READ_DATA_RETURN(pipe, n) \
+	(_PIPE(pipe, _MIPIA_READ_DATA_RETURN0, _MIPIB_READ_DATA_RETURN0) + 4 * (n)) /* n: 0...7 */
+
+#define _MIPIA_READ_DATA_VALID			(VLV_DISPLAY_BASE + 0xb138)
+#define _MIPIB_READ_DATA_VALID			(VLV_DISPLAY_BASE + 0xb938)
+#define MIPI_READ_DATA_VALID(pipe)	_PIPE(pipe, _MIPIA_READ_DATA_VALID, _MIPIB_READ_DATA_VALID)
+#define  READ_DATA_VALID(n)				(1 << (n))
+
 #endif /* _I915_REG_H_ */

Signature · 6 lines

1.7.9.5

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

Signature · 6 lines

Ville Syrjälä
Intel OTC
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

Signature · 5 lines

Jani Nikula, Intel Open Source Technology Center
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

Damien Lespiau

2013-08-15 13:38 UTC #7 lore raw

Re: [PATCH 04/14] drm/i915: add MIPI DSI register definitions

In reply to Jani Nikula

Quoted 6 lines · Jani Nikula

Add definitions for VLV MIPI DSI registers.
Signed-off-by Jani Nikula <[email protected]>
---
 drivers/gpu/drm/i915/i915_reg.h |  409 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 409 insertions(+)

I wonder if it'd be the right time to spawn another header instead of adding more to i915_reg.h? or people are fine with that big i915_reg.h?

Signature · 1 line

Damien

Daniel Vetter

2013-08-15 14:08 UTC #8 lore raw

Re: [PATCH 04/14] drm/i915: add MIPI DSI register definitions

Quoted 10 lines · Damien Lespiau

Quoted 6 lines · Jani Nikula
Add definitions for VLV MIPI DSI registers.
Signed-off-by Jani Nikula <[email protected]>
---
 drivers/gpu/drm/i915/i915_reg.h |  409 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 409 insertions(+)
I wonder if it'd be the right time to spawn another header instead of adding more to i915_reg.h? or people are fine with that big i915_reg.h?

cscope can still keep track of it, so imo it's ok. Stuff we care more about (function declarations, structs, ...) are already in other files, so personally I don't mind really.
-Daniel

Signature · 3 lines

Daniel Vetter
Software Engineer, Intel Corporation
+41 (0) 79 365 57 48 - http://blog.ffwll.ch