mfd: flexcom: add a driver for Flexcom
v5 cover mfd: flexcom: add a driver for Flexcom
ChangeLog
v5:
- create a header file containing macros used by DT bindings
- use numeric constants instead of strings to select the Flexcom mode
- change the license to "GPL v2"
- update the DT binding documentation to make it more readable and add references to USART, SPI and I2C DT binding documentations. remove the useless label in the Example section.
- change the register prefix from FX_ to FLEX_ to match the Flexcom programmer datasheet.
- rename some variables to make them more comprehensive.
v4:
- check clk_prepare_enable() return code in atmel_flexcom_probe()
- add a commit message to the DT binding patch
v3:
- remove MODULE_ALIAS()
- add Acked-by from Boris Brezillon and Alexandre Belloni
v2:
- enhance the documentation of DT bindings and change the way the "ranges" property is used.
- replace __raw_readl() and __raw_writel() by readl() and writel().
- change the module license to "GPL" for v2 or later
- print the selected flexcom mode after the hardware version
v1:
This series of patches a support to the Atmel Flexcom, a wrapper which integrates an USART, a SPI controller and a TWI controller. Only one peripheral can be used at a time. The active function is selected though the Flexcom Mode Register.
Cyrille Pitchen (3):
mfd: atmel-flexcom: create include file with macros used by DT
bindings
mfd: devicetree: add bindings for Atmel Flexcom
mfd: atmel-flexcom: add a driver for Atmel Flexible Serial
Communication Unit
.../devicetree/bindings/mfd/atmel-flexcom.txt | 67 +++++++++++++ drivers/mfd/Kconfig | 11 +++ drivers/mfd/Makefile | 1 + drivers/mfd/atmel-flexcom.c | 104 +++++++++++++++++++++ include/dt-bindings/mfd/atmel-flexcom.h | 16 ++++ 5 files changed, 199 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/atmel-flexcom.txt create mode 100644 drivers/mfd/atmel-flexcom.c create mode 100644 include/dt-bindings/mfd/atmel-flexcom.h
Signature · 1 line
1.8.2.2
PATCH v5 1/3 mfd: atmel-flexcom: create include file with macros used by DT bindings
This patch defines some macros to be used as value for the "atmel,flexcom-mode" DT property. This value is then written into the Operating Mode (OPMODE) bit field of the Flexcom Mode Register.
--- include/dt-bindings/mfd/atmel-flexcom.h | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) create mode 100644 include/dt-bindings/mfd/atmel-flexcom.h
include/dt-bindings/mfd/atmel-flexcom.h new file +16 -0
@@ -0,0 +1,16 @@ +/* +* This header provides macros for Atmel Flexcom DT bindings. +* +* Copyright (C) 2015 Cyrille Pitchen <[email protected]> +* +* GPLv2 only +*/ + +#ifndef __DT_BINDINGS_ATMEL_FLEXCOM_H__ +#define __DT_BINDINGS_ATMEL_FLEXCOM_H__ + +#define ATMEL_FLEXCOM_MODE_USART 1 +#define ATMEL_FLEXCOM_MODE_SPI 2 +#define ATMEL_FLEXCOM_MODE_TWI 3 + +#endif /* __DT_BINDINGS_ATMEL_FLEXCOM_H__ */
Signature · 1 line
1.8.2.2
PATCH v5 2/3 mfd: devicetree: add bindings for Atmel Flexcom
In reply to Cyrille PitchenThis patch documents the DT bindings for the Atmel Flexcom which will be introduced by sama5d2x SoCs. These bindings will be used by the actual Flexcom driver to be sent in another patch.
--- .../devicetree/bindings/mfd/atmel-flexcom.txt | 67 ++++++++++++++++++++++ 1 file changed, 67 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/atmel-flexcom.txt
Documentation/devicetree/bindings/mfd/atmel-flexcom.txt new file +67 -0
@@ -0,0 +1,67 @@ +* Device tree bindings for Atmel Flexcom (Flexible Serial Communication Unit) + +The Atmel Flexcom is just a wrapper which embeds a SPI controller, an I2C +controller and an USART. Only one function can be used at a time and is chosen +at boot time according to the device tree. + +Required properties: +- compatible: "atmel,sama5d2-flexcom" +- reg: shall be the offset/length value for Flexcom dedicated + I/O registers (without USART, TWI or SPI registers). +- clocks: shall be the Flexcom peripheral clock from PMC. +- #address-cells: should be <1> +- #size-cells: should be <1> +- ranges: one range for the full I/O register region (including + USART, TWI and SPI registers). +- atmel,flexcom-mode: should be one of the 3 following macros as defined in + include/dt-bindings/mfd/atmel-flexcom.h: + - ATMEL_FLEXCOM_MODE_USART for USART + - ATMEL_FLEXCOM_MODE_SPI for SPI + - ATMEL_FLEXCOM_MODE_TWI for I2C + +Required child: +a single child device of type matching the "atmel,flexcom-mode" property. + +The reg property of this child should be: +- <0x200 0x200> for USART +- <0x400 0x200> for SPI +- <0x600 0x200> for I2C + +The phandle provided by the clocks property of the child is the same as one for +the Flexcom parent. + +Other properties remain unchanged. See documentation of the respective device: +- ../serial/atmel-usart.txt +- ../spi/spi_atmel.txt +- ../i2c/i2c-at91.txt + +Example: + +flexcom at f8034000 { + compatible = "atmel,sama5d2-flexcom"; + reg = <0xf8034000 0x200>; + clocks = <&flx0_clk>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0xf8034000 0x800>; + atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>; + + spi at f8034400 { + compatible = "atmel,at91rm9200-spi"; + reg = <0x400 0x200>; + interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flx0_default>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&flx0_clk>; + clock-names = "spi_clk"; + atmel,fifo-size = <32>; + + mtd_dataflash at 0 { + compatible = "atmel,at25f512b"; + reg = <0>; + spi-max-frequency = <20000000>; + }; + }; +};
Signature · 1 line
1.8.2.2
PATCH v5 3/3 mfd: atmel-flexcom: add a driver for Atmel Flexible Serial Communication Unit
In reply to Cyrille PitchenThis driver supports the new Atmel Flexcom. The Flexcom is a wrapper which integrates one SPI controller, one I2C controller and one USART. Only one function can be enabled at a time. This driver selects the function once for all, when the Flexcom is probed, according to the value of the new "atmel,flexcom-mode" device tree property.
This driver has chosen to present the Flexcom to the system as a MFD so the implementation is seamless for the existing Atmel SPI, I2C and USART drivers.
Also the Flexcom embeds FIFOs: the latest patches of the SPI, I2C and USART drivers take advantage of this new feature.
--- drivers/mfd/Kconfig | 11 +++++ drivers/mfd/Makefile | 1 + drivers/mfd/atmel-flexcom.c | 104 ++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 116 insertions(+) create mode 100644 drivers/mfd/atmel-flexcom.c
drivers/mfd/Kconfig +11 -0
@@ -59,6 +59,17 @@ config MFD_AAT2870_CORE additional drivers must be enabled in order to use the functionality of the device. +config MFD_ATMEL_FLEXCOM + tristate "Atmel Flexcom (Flexible Serial Communication Unit)" + select MFD_CORE + depends on OF + help + Select this to get support for Atmel Flexcom. This is a wrapper + which embeds a SPI controller, a I2C controller and a USART. Only + one function can be used at a time. The choice is done at boot time + by the probe function of this MFD driver according to a device tree + property. + config MFD_ATMEL_HLCDC tristate "Atmel HLCDC (High-end LCD Controller)" select MFD_CORE
drivers/mfd/Makefile +1 -0
@@ -160,6 +160,7 @@ obj-$(CONFIG_MFD_SPMI_PMIC) += qcom-spmi-pmic.o obj-$(CONFIG_TPS65911_COMPARATOR) += tps65911-comparator.o obj-$(CONFIG_MFD_TPS65090) += tps65090.o obj-$(CONFIG_MFD_AAT2870_CORE) += aat2870-core.o +obj-$(CONFIG_MFD_ATMEL_FLEXCOM) += atmel-flexcom.o obj-$(CONFIG_MFD_ATMEL_HLCDC) += atmel-hlcdc.o obj-$(CONFIG_MFD_INTEL_MSIC) += intel_msic.o obj-$(CONFIG_MFD_PALMAS) += palmas.o
drivers/mfd/atmel-flexcom.c new file +104 -0
104 lines not on this page · raw message
Signature · 1 line
1.8.2.2