Skip to contentSkip to conversation

arm: sun9i: Support AXP808 PMIC and Sunchip CX-A99 board

PATCH Superseded Rask Ingemann Lambertsen 4 participants 17 messages Jan 26, 2017 – Feb 5, 2017

Subsystems (6)

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore
#1 lore raw

PATCH 1/5 DT: mfd: axp20x: Add AXP806 to list of current AXP20x family members

In reply to Rask Ingemann Lambertsen

An entry for the AXP806 was forgotten, so add one.

Fixes 204ae2963e10 ("mfd: axp20x: Add bindings for AXP806 PMIC")
---
 Documentation/devicetree/bindings/mfd/axp20x.txt | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/mfd/axp20x.txt +1 -0
index 8f3ad9a..86ae540 100644
@@ -6,6 +6,7 @@ axp202 (X-Powers)
 axp209 (X-Powers)
 axp221 (X-Powers)
 axp223 (X-Powers)
+axp806 (X-Powers)
 axp809 (X-Powers)
 
 Required properties:
Signature · 6 lines
2.10.2

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
#4 lore raw

PATCH 2/5 DT: mfd: axp20x: Add binding for the AXP808

In reply to Rask Ingemann Lambertsen

The AXP808 does not support address space extension, but is otherwise identical to the AXP806, including the chip ID, so add a compatible string for it to the binding.

---
 Documentation/devicetree/bindings/mfd/axp20x.txt | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)
Documentation/devicetree/bindings/mfd/axp20x.txt +4 -3
index 86ae540..8195b06 100644
@@ -7,12 +7,13 @@ axp209 (X-Powers)
 axp221 (X-Powers)
 axp223 (X-Powers)
 axp806 (X-Powers)
+axp808 (X-Powers)
 axp809 (X-Powers)
 
 Required properties:
 - compatible: "x-powers,axp152", "x-powers,axp202", "x-powers,axp209",
 	      "x-powers,axp221", "x-powers,axp223", "x-powers,axp806",
-	      "x-powers,axp809"
+	      "x-powers,axp808", "x-powers,axp809"
 - reg: The I2C slave address or RSB hardware address for the AXP chip
 - interrupt-parent: The parent interrupt controller
 - interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
@@ -87,7 +88,7 @@ LDO_IO1		: LDO		: ips-supply		: GPIO 1
 RTC_LDO		: LDO		: ips-supply		: always on
 DRIVEVBUS	: Enable output	: drivevbus-supply	: external regulator
 
-AXP806 regulators, type, and corresponding input supply names:
+AXP806/AXP808 regulators, type, and corresponding input supply names:
 
 Regulator	  Type		  Supply Name		  Notes
 ---------	  ----		  -----------		  -----
@@ -108,7 +109,7 @@ CLDO2		: LDO		: cldoin-supply		: shared supply
 CLDO3		: LDO		: cldoin-supply		: shared supply
 SW		: On/Off Switch : swin-supply
 
-Additionally, the AXP806 DC-DC regulators support poly-phase arrangements
+Additionally, the AXP806/AXP808 DC-DC regulators support poly-phase arrangements
 for higher output current. The possible groupings are: A+B, A+B+C, D+E.
 
 AXP809 regulators, type, and corresponding input supply names:
Signature · 6 lines
2.10.2

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
#7 lore raw

PATCH 3/5 mfd: axp20x: Add support for the AXP808 PMIC

In reply to Rask Ingemann Lambertsen

The X-Powers AXP808 is a PMIC which, like the very similar AXP806, is used on boards featuring Allwinner's A80 SoC. Unlike the AXP806, it doesn't support address space extension and its associated registers, but the two are otherwise identical (including the chip ID).

This patch adds support for the interrupts on the AXP808 and enables the regulator sub-device. The next patch in the series adds the actual regulator support.

---
 drivers/mfd/axp20x-rsb.c   |  1 +
 drivers/mfd/axp20x.c       | 28 ++++++++++++++++++++++++++++
 include/linux/mfd/axp20x.h |  1 +
 3 files changed, 30 insertions(+)
drivers/mfd/axp20x-rsb.c +1 -0
index a732cb5..96ea2e9 100644
@@ -62,6 +62,7 @@ static int axp20x_rsb_remove(struct sunxi_rsb_device *rdev)
 static const struct of_device_id axp20x_rsb_of_match[] = {
 	{ .compatible = "x-powers,axp223", .data = (void *)AXP223_ID },
 	{ .compatible = "x-powers,axp806", .data = (void *)AXP806_ID },
+	{ .compatible = "x-powers,axp808", .data = (void *)AXP808_ID },
 	{ .compatible = "x-powers,axp809", .data = (void *)AXP809_ID },
 	{ },
 };
drivers/mfd/axp20x.c +28 -0
index 25115fe..2d3383e 100644
@@ -41,6 +41,7 @@ static const char * const axp20x_model_names[] = {
 	"AXP223",
 	"AXP288",
 	"AXP806",
+	"AXP808",
 	"AXP809",
 };
 
@@ -148,6 +149,13 @@ static const struct regmap_range axp806_writeable_ranges[] = {
 	regmap_reg_range(AXP806_REG_ADDR_EXT, AXP806_REG_ADDR_EXT),
 };
 
+static const struct regmap_range axp808_writeable_ranges[] = {
+	regmap_reg_range(AXP20X_DATACACHE(0), AXP20X_DATACACHE(3)),
+	regmap_reg_range(AXP806_PWR_OUT_CTRL1, AXP806_CLDO3_V_CTRL),
+	regmap_reg_range(AXP20X_IRQ1_EN, AXP20X_IRQ2_EN),
+	regmap_reg_range(AXP20X_IRQ1_STATE, AXP20X_IRQ2_STATE),
+};
+
 static const struct regmap_range axp806_volatile_ranges[] = {
 	regmap_reg_range(AXP20X_IRQ1_STATE, AXP20X_IRQ2_STATE),
 };
@@ -162,6 +170,11 @@ static const struct regmap_access_table axp806_volatile_table = {
 	.n_yes_ranges	= ARRAY_SIZE(axp806_volatile_ranges),
 };
 
+static const struct regmap_access_table axp808_writeable_table = {
+	.yes_ranges	= axp808_writeable_ranges,
+	.n_yes_ranges	= ARRAY_SIZE(axp808_writeable_ranges),
+};
+
 static struct resource axp152_pek_resources[] = {
 	DEFINE_RES_IRQ_NAMED(AXP152_IRQ_PEK_RIS_EDGE, "PEK_DBR"),
 	DEFINE_RES_IRQ_NAMED(AXP152_IRQ_PEK_FAL_EDGE, "PEK_DBF"),
@@ -320,6 +333,15 @@ static const struct regmap_config axp806_regmap_config = {
 	.cache_type	= REGCACHE_RBTREE,
 };
 
+static const struct regmap_config axp808_regmap_config = {
+	.reg_bits	= 8,
+	.val_bits	= 8,
+	.wr_table	= &axp808_writeable_table,
+	.volatile_table	= &axp806_volatile_table,
+	.max_register	= AXP806_VREF_TEMP_WARN_L,
+	.cache_type	= REGCACHE_RBTREE,
+};
+
 #define INIT_REGMAP_IRQ(_variant, _irq, _off, _mask)			\
 	[_variant##_IRQ_##_irq] = { .reg_offset = (_off), .mask = BIT(_mask) }
 
@@ -842,6 +864,12 @@ int axp20x_match_device(struct axp20x_dev *axp20x)
 		axp20x->regmap_cfg = &axp806_regmap_config;
 		axp20x->regmap_irq_chip = &axp806_regmap_irq_chip;
 		break;
+	case AXP808_ID:
+		axp20x->nr_cells = ARRAY_SIZE(axp806_cells);
+		axp20x->cells = axp806_cells;
+		axp20x->regmap_cfg = &axp808_regmap_config;
+		axp20x->regmap_irq_chip = &axp806_regmap_irq_chip;
+		break;
 	case AXP809_ID:
 		axp20x->nr_cells = ARRAY_SIZE(axp809_cells);
 		axp20x->cells = axp809_cells;
include/linux/mfd/axp20x.h +1 -0
index 0aa4ef7..b9b7eae 100644
@@ -21,6 +21,7 @@ enum {
 	AXP223_ID,
 	AXP288_ID,
 	AXP806_ID,
+	AXP808_ID,
 	AXP809_ID,
 	NR_AXP20X_VARIANTS,
 };
Signature · 1 line
2.10.2
#10 lore raw

PATCH 4/5 regulator: axp20x: Add support for the AXP808 PMIC

In reply to Rask Ingemann Lambertsen

The regulators are the same as on the AXP806.

---
 drivers/regulator/axp20x-regulator.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)
drivers/regulator/axp20x-regulator.c +5 -2
index a3ade9e..034dce8 100644
@@ -370,6 +370,7 @@ static int axp20x_set_dcdc_freq(struct platform_device *pdev, u32 dcdcfreq)
 		step = 75;
 		break;
 	case AXP806_ID:
+	case AXP808_ID:
 		/*
 		 * AXP806 DCDC work frequency setting has the same range and
 		 * step as AXP22X, but at a different register.
@@ -459,6 +460,7 @@ static int axp20x_set_dcdc_workmode(struct regulator_dev *rdev, int id, u32 work
 		break;
 
 	case AXP806_ID:
+	case AXP808_ID:
 		reg = AXP806_DCDC_MODE_CTRL2;
 		/*
 		 * AXP806 DCDC regulator IDs have the same range as AXP22X.
@@ -492,8 +494,8 @@ static bool axp20x_is_polyphase_slave(struct axp20x_dev *axp20x, int id)
 {
 	u32 reg = 0;
 
-	/* Only AXP806 has poly-phase outputs */
-	if (axp20x->variant != AXP806_ID)
+	/* Only AXP806 and AXP808 have poly-phase outputs */
+	if (axp20x->variant != AXP806_ID && axp20x->variant != AXP808_ID)
 		return false;
 
 	regmap_read(axp20x->regmap, AXP806_DCDC_MODE_CTRL2, &reg);
@@ -541,6 +543,7 @@ static int axp20x_regulator_probe(struct platform_device *pdev)
 						  "x-powers,drive-vbus-en");
 		break;
 	case AXP806_ID:
+	case AXP808_ID:
 		regulators = axp806_regulators;
 		nregulators = AXP806_REG_ID_MAX;
 		break;
Signature · 1 line
2.10.2
#0 lore raw

cover arm: sun9i: Support AXP808 PMIC and Sunchip CX-A99 board

This patch series add support for the Sunchip CX-A99 board, which is used in a few media players, making it the third device with an Allwinner A80 SoC to be supported. The board uses the X-Powers AXP808 PMIC which this patch series also adds support for.

Patch 1 adds a documentation line which was forgotten when device tree bindings for the axp20x family were updated for the AXP806 PMIC. A line immediately below the missing line will be inserted by patch 2, so I'm including patch 1 in this series to avoid conflicts between patches.

Patch 2 adds the AXP808 to the axp20x device tree bindings.

Patch 3 adds support for the AXP808 to the axp20x MFD driver.

Patch 4 adds support for the AXP808 to the axp20x regulator driver.

Patch 5 add the device tree for the Sunchip CX-A99 board. This patch is v5 of the only remaining patch from v4 of the patch series posted back in August. Support for the AXP808 has made major improvements possible, notably Wifi.

Before trying out this patch series, you must also apply the patch "regulator: axp20x: AXP806: Fix dcdcb being set instead of dcdce" [1] to avoid damage to the DRAM chips through over-voltage.

[1] https://patchwork.kernel.org/patch/9530319/

Rask Ingemann Lambertsen (5):
DT: mfd: axp20x: Add AXP806 to list of current AXP20x family members
DT: mfd: axp20x: Add binding for the AXP808
mfd: axp20x: Add support for the AXP808 PMIC
regulator: axp20x: Add support for the AXP808 PMIC
ARM: dts: sun9i: Initial support for the Sunchip CX-A99 board

 Documentation/devicetree/bindings/mfd/axp20x.txt |   8 +-
 arch/arm/boot/dts/Makefile                       |   3 +-
 arch/arm/boot/dts/sun9i-a80-cx-a99.dts           | 413 +++++++++++++++++++++++
 drivers/mfd/axp20x-rsb.c                         |   1 +
 drivers/mfd/axp20x.c                             |  28 ++
 drivers/regulator/axp20x-regulator.c             |   7 +-
 include/linux/mfd/axp20x.h                       |   1 +
 7 files changed, 455 insertions(+), 6 deletions(-)
 create mode 100644 arch/arm/boot/dts/sun9i-a80-cx-a99.dts
Signature · 1 line
2.10.2
#13 lore raw

PATCH 5/5 ARM: dts: sun9i: Initial support for the Sunchip CX-A99 board

The Suncip CX-A99 board is found in at least four brands of media players. It features an Allwinner A80 ARM SoC and is found in two models:

1) 2 GiB DDR3 DRAM and 16 GB eMMC
2) 4 GiB DDR3 DRAM and 32 GB eMMC

For details of the board, see the linux-sunxi page <URL:https://linux-sunxi.org/Sunchip_CX-A99>.

Supported features (+ means tested):
+ One Cortex-A7 CPU core
+ AXP808 power management chip
+ OZ80120 voltage regulator
+ Serial console port (internal)
+ eMMC and SD card slot
+ USB 2.0 host ports on on-board USB hub
+ SATA port on on-board SATA-to-USB bridge *
+ IEEE 802.11 a/b/g/n/ac SDIO Wifi
+ Real-time clock
+ LEDs
- IR receiver for remote control

* In addition to connecting a SATA device, some unknown magic is necessary after power-up to get the SATA-to-USB bridge to show up on the USB bus. As a workaround, run the vendor U-Boot once after power-up.

So far unsupported features:
- Using more than one CPU core or any of the Cortex-A15 CPU cores
- USB 3.0 OTG port (except for supplying 5V power)
- IEEE 802.3 10/100/1000 megabit Ethernet
- HDMI connector
- SPDIF audio output
- Jack socket with composite video and analog stereo audio
- Bluetooth
- FM radio receiver (assuming it is even wired on the board)

---

Changes in v5:
- Switched pinmux modes to generic properties and dropped #include <dt-bindings/pinctrl/sun4i-a10.h> as a consequence.
- Dropped pinctrl properties from GPIO nodes and dropped the pinmux nodes for them.
- AXP808 regulators added.
- Dropped the now unused #include <sunxi-common-regulators.dtsi>.
- Ampak AP6335 SDIO-Wifi added.
- USB Vbus changes as per v4 comments.
- Added "broken-cd" to mmc0 because GPIO interrupts don't work.

Changes in v4:
- Node names had underscores changed to hyphens.
- Changed formatting of the ac100/rtc node's clock output name list to match that of the same node in the cubieboard4 and a80-optimus device trees.

Changes in v3:
None.

Changes in v2:
- Fixed formatting and style issues found by scripts/checkpatch.pl.

 arch/arm/boot/dts/Makefile             |   3 +-
 arch/arm/boot/dts/sun9i-a80-cx-a99.dts | 413 +++++++++++++++++++++++++++++++++
 2 files changed, 415 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/sun9i-a80-cx-a99.dts
arch/arm/boot/dts/Makefile +2 -1
index e7994df..d9f47e1 100644
@@ -859,7 +859,8 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-r16-parrot.dtb
 dtb-$(CONFIG_MACH_SUN9I) += \
 	sun9i-a80-optimus.dtb \
-	sun9i-a80-cubieboard4.dtb
+	sun9i-a80-cubieboard4.dtb \
+	sun9i-a80-cx-a99.dtb
 dtb-$(CONFIG_ARCH_TANGO) += \
 	tango4-vantage-1172.dtb
 dtb-$(CONFIG_ARCH_TEGRA_2x_SOC) += \
arch/arm/boot/dts/sun9i-a80-cx-a99.dts new file +413 -0

413 lines not on this page · raw message

Signature · 1 line
2.10.2
#16 lore raw
In reply to Rask Ingemann Lambertsen

Please Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org on replies as I accidentally left it out when mailing out this series. I have sent a copy with identical
message-ids to linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org, so replies should be threaded properly.

Signature · 5 lines
Rask Ingemann Lambertsen
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
maintainer Acked-by on v1 4/5
#11 lore raw

Re: [PATCH 4/5] regulator: axp20x: Add support for the AXP808 PMIC

In reply to Rask Ingemann Lambertsen
Quoted 1 line · Rask Ingemann Lambertsen

The regulators are the same as on the AXP806.

-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 488 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170127/f7f39ea4/attachment.sig>

maintainer Acked-by on v1 1/5
#3 lore raw

Re: [PATCH 1/5] DT: mfd: axp20x: Add AXP806 to list of current AXP20x family members

In reply to Rask Ingemann Lambertsen
Quoted 7 lines · Rask Ingemann Lambertsen

An entry for the AXP806 was forgotten, so add one.

Fixes 204ae2963e10 ("mfd: axp20x: Add bindings for AXP806 PMIC")
---
 Documentation/devicetree/bindings/mfd/axp20x.txt | 1 +
 1 file changed, 1 insertion(+)
maintainer Acked-by on v1 2/5
#5 lore raw

Re: [PATCH 2/5] DT: mfd: axp20x: Add binding for the AXP808

In reply to Rask Ingemann Lambertsen
Quoted 8 lines · Rask Ingemann Lambertsen

The AXP808 does not support address space extension, but is otherwise identical to the AXP806, including the chip ID, so add a compatible string for it to the binding.

---
 Documentation/devicetree/bindings/mfd/axp20x.txt | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)
Acked-by
#6 lore raw

Re: [PATCH 2/5] DT: mfd: axp20x: Add binding for the AXP808

Quoted 11 lines · Rob Herring
Quoted 8 lines · Rask Ingemann Lambertsen

The AXP808 does not support address space extension, but is otherwise identical to the AXP806, including the chip ID, so add a compatible string for it to the binding.

---
 Documentation/devicetree/bindings/mfd/axp20x.txt | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)
Acked-by on v1 3/5
#8 lore raw

Re: [PATCH 3/5] mfd: axp20x: Add support for the AXP808 PMIC

In reply to Rask Ingemann Lambertsen
Quoted 10 lines · Rask Ingemann Lambertsen

The X-Powers AXP808 is a PMIC which, like the very similar AXP806, is used on boards featuring Allwinner's A80 SoC. Unlike the AXP806, it doesn't support address space extension and its associated registers, but the two are otherwise identical (including the chip ID).

This patch adds support for the interrupts on the AXP808 and enables the regulator sub-device. The next patch in the series adds the actual regulator support.

Quoted 45 lines
---
 drivers/mfd/axp20x-rsb.c   |  1 +
 drivers/mfd/axp20x.c       | 28 ++++++++++++++++++++++++++++
 include/linux/mfd/axp20x.h |  1 +
 3 files changed, 30 insertions(+)
drivers/mfd/axp20x-rsb.c +1 -0
index a732cb5..96ea2e9 100644
@@ -62,6 +62,7 @@ static int axp20x_rsb_remove(struct sunxi_rsb_device *rdev)
 static const struct of_device_id axp20x_rsb_of_match[] = {
        { .compatible = "x-powers,axp223", .data = (void *)AXP223_ID },
        { .compatible = "x-powers,axp806", .data = (void *)AXP806_ID },
+       { .compatible = "x-powers,axp808", .data = (void *)AXP808_ID },
        { .compatible = "x-powers,axp809", .data = (void *)AXP809_ID },
        { },
 };
drivers/mfd/axp20x.c +8 -0
index 25115fe..2d3383e 100644
@@ -41,6 +41,7 @@ static const char * const axp20x_model_names[] = {
        "AXP223",
        "AXP288",
        "AXP806",
+       "AXP808",
        "AXP809",
 };
 
@@ -148,6 +149,13 @@ static const struct regmap_range axp806_writeable_ranges[] = {
        regmap_reg_range(AXP806_REG_ADDR_EXT, AXP806_REG_ADDR_EXT),
 };
 
+static const struct regmap_range axp808_writeable_ranges[] = {
+       regmap_reg_range(AXP20X_DATACACHE(0), AXP20X_DATACACHE(3)),
+       regmap_reg_range(AXP806_PWR_OUT_CTRL1, AXP806_CLDO3_V_CTRL),
+       regmap_reg_range(AXP20X_IRQ1_EN, AXP20X_IRQ2_EN),
+       regmap_reg_range(AXP20X_IRQ1_STATE, AXP20X_IRQ2_STATE),
+};
+
 static const struct regmap_range axp806_volatile_ranges[] = {
        regmap_reg_range(AXP20X_IRQ1_STATE, AXP20X_IRQ2_STATE),
 };

drivers/mfd/axp20x.c static const struct regmap_access_table axp806_volatile_table = { · line 175

Quoted 6 lines
drivers/mfd/axp20x.c +3 -0
@@ -162,6 +170,11 @@ static const struct regmap_access_table axp806_volatile_table = {
        .n_yes_ranges   = ARRAY_SIZE(axp806_volatile_ranges),
 };
 
+static const struct regmap_access_table axp808_writeable_table = {
+       .yes_ranges     = axp808_writeable_ranges,
+       .n_yes_ranges   = ARRAY_SIZE(axp808_writeable_ranges),

You could probably get away with using axp806_writeable_ranges, and pass ARRAY_SIZE(axp808_writeable_ranges) - 1 for .n_yes_ranges.

Or maybe the compiler figures out the 2 arrays share common data.

ChenYu

Quoted 54 lines
drivers/mfd/axp20x.c +17 -0
+};
+
 static struct resource axp152_pek_resources[] = {
        DEFINE_RES_IRQ_NAMED(AXP152_IRQ_PEK_RIS_EDGE, "PEK_DBR"),
        DEFINE_RES_IRQ_NAMED(AXP152_IRQ_PEK_FAL_EDGE, "PEK_DBF"),
@@ -320,6 +333,15 @@ static const struct regmap_config axp806_regmap_config = {
        .cache_type     = REGCACHE_RBTREE,
 };
 
+static const struct regmap_config axp808_regmap_config = {
+       .reg_bits       = 8,
+       .val_bits       = 8,
+       .wr_table       = &axp808_writeable_table,
+       .volatile_table = &axp806_volatile_table,
+       .max_register   = AXP806_VREF_TEMP_WARN_L,
+       .cache_type     = REGCACHE_RBTREE,
+};
+
 #define INIT_REGMAP_IRQ(_variant, _irq, _off, _mask)                   \
        [_variant##_IRQ_##_irq] = { .reg_offset = (_off), .mask = BIT(_mask) }
 
@@ -842,6 +864,12 @@ int axp20x_match_device(struct axp20x_dev *axp20x)
                axp20x->regmap_cfg = &axp806_regmap_config;
                axp20x->regmap_irq_chip = &axp806_regmap_irq_chip;
                break;
+       case AXP808_ID:
+               axp20x->nr_cells = ARRAY_SIZE(axp806_cells);
+               axp20x->cells = axp806_cells;
+               axp20x->regmap_cfg = &axp808_regmap_config;
+               axp20x->regmap_irq_chip = &axp806_regmap_irq_chip;
+               break;
        case AXP809_ID:
                axp20x->nr_cells = ARRAY_SIZE(axp809_cells);
                axp20x->cells = axp809_cells;
include/linux/mfd/axp20x.h +1 -1
index 0aa4ef7..b9b7eae 100644
@@ -21,6 +21,7 @@ enum {
        AXP223_ID,
        AXP288_ID,
        AXP806_ID,
+       AXP808_ID,
        AXP809_ID,
        NR_AXP20X_VARIANTS,
 };
--

2.10.2

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#14 lore raw

Re: [PATCH 5/5] ARM: dts: sun9i: Initial support for the Sunchip CX-A99 board

In reply to Rask Ingemann Lambertsen

Hi,

Quoted 157 lines · Rask Ingemann Lambertsen

The Suncip CX-A99 board is found in at least four brands of media players. It features an Allwinner A80 ARM SoC and is found in two models:

1) 2 GiB DDR3 DRAM and 16 GB eMMC
2) 4 GiB DDR3 DRAM and 32 GB eMMC

For details of the board, see the linux-sunxi page <URL:https://linux-sunxi.org/Sunchip_CX-A99>.

Supported features (+ means tested):
+ One Cortex-A7 CPU core
+ AXP808 power management chip
+ OZ80120 voltage regulator
+ Serial console port (internal)
+ eMMC and SD card slot
+ USB 2.0 host ports on on-board USB hub
+ SATA port on on-board SATA-to-USB bridge *
+ IEEE 802.11 a/b/g/n/ac SDIO Wifi
+ Real-time clock
+ LEDs
- IR receiver for remote control

* In addition to connecting a SATA device, some unknown magic is necessary after power-up to get the SATA-to-USB bridge to show up on the USB bus. As a workaround, run the vendor U-Boot once after power-up.

So far unsupported features:
- Using more than one CPU core or any of the Cortex-A15 CPU cores
- USB 3.0 OTG port (except for supplying 5V power)
- IEEE 802.3 10/100/1000 megabit Ethernet
- HDMI connector
- SPDIF audio output
- Jack socket with composite video and analog stereo audio
- Bluetooth
- FM radio receiver (assuming it is even wired on the board)

---

Changes in v5:
- Switched pinmux modes to generic properties and dropped #include <dt-bindings/pinctrl/sun4i-a10.h> as a consequence.
- Dropped pinctrl properties from GPIO nodes and dropped the pinmux nodes for them.
- AXP808 regulators added.
- Dropped the now unused #include <sunxi-common-regulators.dtsi>.
- Ampak AP6335 SDIO-Wifi added.
- USB Vbus changes as per v4 comments.
- Added "broken-cd" to mmc0 because GPIO interrupts don't work.

Changes in v4:
- Node names had underscores changed to hyphens.
- Changed formatting of the ac100/rtc node's clock output name list to match that of the same node in the cubieboard4 and a80-optimus device trees.

Changes in v3:
None.

Changes in v2:
- Fixed formatting and style issues found by scripts/checkpatch.pl.

 arch/arm/boot/dts/Makefile             |   3 +-
 arch/arm/boot/dts/sun9i-a80-cx-a99.dts | 413 +++++++++++++++++++++++++++++++++
 2 files changed, 415 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/sun9i-a80-cx-a99.dts
arch/arm/boot/dts/Makefile +2 -1
index e7994df..d9f47e1 100644
@@ -859,7 +859,8 @@ dtb-$(CONFIG_MACH_SUN8I) += \
        sun8i-r16-parrot.dtb
 dtb-$(CONFIG_MACH_SUN9I) += \
        sun9i-a80-optimus.dtb \
-       sun9i-a80-cubieboard4.dtb
+       sun9i-a80-cubieboard4.dtb \
+       sun9i-a80-cx-a99.dtb
 dtb-$(CONFIG_ARCH_TANGO) += \
        tango4-vantage-1172.dtb
 dtb-$(CONFIG_ARCH_TEGRA_2x_SOC) += \
arch/arm/boot/dts/sun9i-a80-cx-a99.dts new file +71 -0
new file mode 100644
index 0000000..8925093
@@ -0,0 +1,413 @@
+/*
+ * sun9i-a80-cx-a99.dts - Device Tree file for the Sunchip CX-A99 board.
+ *
+ * Copyright (C) 2017 Rask Ingemann Lambertsen <[email protected]>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/*
+ * The Sunchip CX-A99 board is found in several similar Android media
+ * players, such as:
+ *
+ * Instabox Fantasy A8 (no external antenna)
+ * Jesurun CS-Q8 (ships with larger remote control)
+ * Jesurun Maxone
+ * Rikomagic (RKM) MK80/MK80LE
+ * Tronsmart Draco AW80 Meta/Telos
+ *
+ * See <URL:https://linux-sunxi.org/Sunchip_CX-A99> for more information.
+ */
+
+/dts-v1/;
+#include "sun9i-a80.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+       model = "Sunchip CX-A99";
+       compatible = "sunchip,cx-a99", "allwinner,sun9i-a80";
+
+       aliases {
+               serial0 = &uart0;
+       };
+
+       chosen {

arch/arm/boot/dts/sun9i-a80-cx-a99.dts line 81

Quoted 10 lines
arch/arm/boot/dts/sun9i-a80-cx-a99.dts new file +10 -0
+               stdout-path = "serial0:115200n8";
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               blue {
+                       gpios = <&pio 6 10 GPIO_ACTIVE_HIGH>;   /* PG10 */
+                       label = "cx-a99:blue:status";
+                       default-state = "on";

Please add a note justifying default-state = "on".

Quoted 15 lines
arch/arm/boot/dts/sun9i-a80-cx-a99.dts new file +15 -0
+               };
+
+               red {
+                       gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>;   /* PG11 */
+                       label = "cx-a99:red:status";
+               };
+       };
+
+       powerseq_wifi: powerseq-wifi {
+               compatible = "mmc-pwrseq-simple";
+               clocks = <&ac100_rtc 1>;
+               clock-names = "ext_clock";
+               reset-gpios = <&r_pio 1 0 GPIO_ACTIVE_LOW>;     /* PM0 */
+               post-power-on-delay-ms = <1>;   /* Minimum 2 cycles. */
+       };

arch/arm/boot/dts/sun9i-a80-cx-a99.dts line 106

Quoted 10 lines
arch/arm/boot/dts/sun9i-a80-cx-a99.dts new file +10 -0
+
+       /* USB 3.0 OTG connector. For now, only Vbus is supported. */
+       reg_usb0_vbus: regulator-usb0-vbus {
+               compatible = "regulator-fixed";
+               regulator-name = "usb0-vbus";
+               regulator-min-microvolt = <5000000>;
+               regulator-max-microvolt = <5000000>;
+               gpio = <&pio 7 15 GPIO_ACTIVE_HIGH>;    /* PH15 */
+               enable-active-high;
+               regulator-always-on;

It's bad to leave VBUS for OTG connectors on. You never know what is plugged in.

Quoted 62 lines
arch/arm/boot/dts/sun9i-a80-cx-a99.dts new file +62 -0
+       };
+
+       /*
+        * A GL850G hub with two external USB connectors is connected
+        * to ehci0. Each has a Vbus regulator controlled by a GPIO:
+        * PL7 for port 1, closest to the 12 V power connector, and
+        * PL8 for port 2, next to the SD card slot.
+        * Because regulator-fixed doesn't support a GPIO list, and
+        * allwinner,sun9i-a80-usb-phy doesn't support more than one
+        * supply, we have to use regulator-always-on on usb1-2-vbus.
+        * Note that the GPIO pins also need cldo1 to be enabled.
+        */
+       reg_usb1_1_vbus: regulator-usb1-1-vbus {
+               compatible = "regulator-fixed";
+               regulator-name = "usb1-1-vbus";
+               regulator-min-microvolt = <5000000>;
+               regulator-max-microvolt = <5000000>;
+               gpio = <&r_pio 0 7 GPIO_ACTIVE_HIGH>;   /* PL7 */
+               enable-active-high;
+       };
+
+       reg_usb1_2_vbus: regulator-usb1-2-vbus {
+               compatible = "regulator-fixed";
+               regulator-name = "usb1-2-vbus";
+               regulator-min-microvolt = <5000000>;
+               regulator-max-microvolt = <5000000>;
+               gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>;   /* PL8 */
+               enable-active-high;
+               regulator-always-on;
+       };
+
+       /* OZ80120 voltage regulator for the four Cortex-A15 cores. */
+       reg_vdd_cpub: regulator-vdd-cpub {
+               compatible = "regulator-gpio";
+
+               regulator-boot-on;
+               regulator-always-on;
+               regulator-min-microvolt = < 800000>;
+               regulator-max-microvolt = <1100000>;
+               regulator-name = "vdd-cpub";
+
+               enable-gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>;    /* PL2 */
+               enable-active-high;
+               gpios = <&r_pio 0 3 GPIO_ACTIVE_HIGH>,          /* PL3 */
+                       <&r_pio 0 4 GPIO_ACTIVE_HIGH>,          /* PL4 */
+                       <&r_pio 0 5 GPIO_ACTIVE_HIGH>;          /* PL5 */
+
+               gpios-states = <1 0 0>;
+               states = <       750000 0x7
+                                800000 0x3
+                                850000 0x5
+                                900000 0x1
+                                950000 0x6
+                               1000000 0x2
+                               1100000 0x4
+                               1200000 0x0>;
+       };
+};
+
+&ehci0 {
+       status = "okay";
+};

arch/arm/boot/dts/sun9i-a80-cx-a99.dts line 178

Quoted 10 lines
arch/arm/boot/dts/sun9i-a80-cx-a99.dts new file +10 -0
+
+&ehci2 {
+       status = "okay";
+};
+
+/* SD card slot. */
+&mmc0 {
+       bus-width = <4>;
+       cd-gpios = <&pio 7 17 GPIO_ACTIVE_LOW>; /* PH17 */
+       broken-cd;                              /* Interrupts don't work. */

This should be handled by the driver.

Quoted 93 lines
arch/arm/boot/dts/sun9i-a80-cx-a99.dts new file +93 -0
+       pinctrl-names = "default";
+       pinctrl-0 = <&mmc0_pins>;
+       vmmc-supply = <&reg_dcdce>;
+       status = "okay";
+};
+
+/* Ampak AP6335 IEEE 802.11 a/b/g/n/ac "Wifi". */
+&mmc1 {
+       bus-width = <4>;
+       non-removable;
+       pinctrl-names = "default";
+       pinctrl-0 = <&mmc1_pins>;
+       vmmc-supply = <&reg_cldo3>;     /* See cldo2,cldo3 note. */
+       vqmmc-supply = <&reg_aldo2>;
+       mmc-pwrseq = <&powerseq_wifi>;
+       status = "okay";
+};
+
+/* On-board eMMC card. */
+&mmc2 {
+       bus-width = <8>;
+       non-removable;
+       pinctrl-names = "default";
+       pinctrl-0 = <&mmc2_8bit_pins>;
+       vmmc-supply = <&reg_dcdce>;
+       status = "okay";
+};
+
+&osc32k {
+       clocks = <&ac100_rtc 0>;
+};
+
+&r_ir {
+       status = "okay";
+};
+
+&r_rsb {
+       status = "okay";
+
+       ac100: codec at e89 {
+               compatible = "x-powers,ac100";
+               reg = <0xe89>;
+
+               ac100_codec: codec {
+                       compatible = "x-powers,ac100-codec";
+                       interrupt-parent = <&r_pio>;
+                       interrupts = <0 9 IRQ_TYPE_LEVEL_LOW>;  /* PL9 */
+                       #clock-cells = <0>;
+                       clock-output-names = "4M_adda";
+               };
+
+               ac100_rtc: rtc {
+                       compatible = "x-powers,ac100-rtc";
+                       interrupt-parent = <&nmi_intc>;
+                       interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+                       clocks = <&ac100_codec>;
+                       #clock-cells = <1>;
+                       clock-output-names = "cko1_rtc",
+                                            "cko2_rtc",
+                                            "cko3_rtc";
+               };
+       };
+
+       pmic at 745 {
+               compatible = "x-powers,axp808", "x-powers,axp806";
+               reg = <0x745>;
+               interrupt-parent = <&nmi_intc>;
+               interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+               interrupt-controller;
+               #interrupt-cells = <1>;
+
+               swin-supply = <&reg_dcdce>;
+
+               /* In comments: Status taken from vendor sys_config1.fex. */
+               regulators {
+                       /* 3.0 V (enabled). */
+                       reg_aldo1: aldo1 {
+                               regulator-boot-on;
+                               regulator-min-microvolt = <3000000>;
+                               regulator-max-microvolt = <3000000>;
+                               regulator-name = "vcc-3v0-1";
+                       };
+
+                       /* 1.8 V (enabled). */
+                       reg_aldo2: aldo2 {
+                               regulator-boot-on;
+                               regulator-min-microvolt = <1800000>;
+                               regulator-max-microvolt = <3600000>;
+                               regulator-name = "vcc-pg-pm-wifi+btio-audio";
+                       };
+
+                       /* 2.5 V (enabled). */
+                       reg_aldo3: aldo3 {

arch/arm/boot/dts/sun9i-a80-cx-a99.dts line 281

Quoted 10 lines
arch/arm/boot/dts/sun9i-a80-cx-a99.dts new file +10 -0
+                               regulator-boot-on;
+                               regulator-min-microvolt = <2500000>;
+                               regulator-max-microvolt = <2500000>;
+                               regulator-name = "vcc-pa-gmac2v5";
+                       };
+
+                       /* 1.8 V (enabled). */
+                       reg_bldo1: bldo1 {
+                               regulator-boot-on;
+                               regulator-always-on;    /* Hang if disabled */

If you specify always-on, you don't need to add boot-on.

Quoted 91 lines
arch/arm/boot/dts/sun9i-a80-cx-a99.dts new file +91 -0
+                               regulator-min-microvolt = <1800000>;
+                               regulator-max-microvolt = <1800000>;
+                               regulator-name = "vdd18-dll-vcc18-pll";
+                       };
+
+                       /* 0.9 V (enabled). */
+                       reg_bldo2: bldo2 {
+                               regulator-boot-on;
+                               regulator-always-on;    /* Hang if disabled */
+                               regulator-min-microvolt = < 800000>;
+                               regulator-max-microvolt = <1100000>;
+                               regulator-name = "vdd-cpus";
+                       };
+
+                       /* 1.2 V (disabled). */
+                       reg_bldo3: bldo3 {
+                               regulator-min-microvolt = <1200000>;
+                               regulator-max-microvolt = <1200000>;
+                               regulator-name = "vcc12-hsic";
+                       };
+
+                       /* 1.1 V (enabled). */
+                       reg_bldo4: bldo4 {
+                               regulator-boot-on;
+                               regulator-min-microvolt = <1100000>;
+                               regulator-max-microvolt = <1100000>;
+                               regulator-name = "vdd09-hdmi";
+                       };
+
+                       /* 3.3 V (enabled). PLx pins control some regulators. */
+                       reg_cldo1: cldo1 {
+                               regulator-boot-on;
+                               regulator-always-on;
+                               regulator-min-microvolt = <3300000>;
+                               regulator-max-microvolt = <3300000>;
+                               regulator-name = "vcc-pl-led";
+                       };
+
+                       /*
+                        * cldo2 and cldo3 are connected in parallel.
+                        * There is currently no way to express that.
+                        * For now, use regulator-always-on on cldo2 and lock
+                        * the voltage on both to 3.3 V.
+                        *
+                        * 3.3 V (disabled).
+                        */
+                       reg_cldo2: cldo2 {
+                               regulator-always-on;
+                               regulator-min-microvolt = <3300000>;
+                               regulator-max-microvolt = <3300000>;
+                               regulator-name = "vbat2-wifi+bt";
+                       };
+
+                       /* 3.3 V (disabled). */
+                       reg_cldo3: cldo3 {
+                               regulator-min-microvolt = <3300000>;
+                               regulator-max-microvolt = <3300000>;
+                               regulator-name = "vbat1-wifi+bt";
+                       };
+
+                       /* 0.9 V (enabled). */
+                       reg_dcdca: dcdca {
+                               regulator-boot-on;
+                               regulator-always-on;
+                               regulator-min-microvolt = < 800000>;
+                               regulator-max-microvolt = <1100000>;
+                               regulator-name = "vdd-cpua";
+                       };
+
+                       /* 1.5 V (enabled). */
+                       reg_dcdcb: dcdcb {
+                               regulator-boot-on;
+                               regulator-always-on;
+                               regulator-min-microvolt = <1500000>;
+                               regulator-max-microvolt = <1500000>;
+                               regulator-name = "vcc-dram";
+                       };
+
+                       /* 0.9 V (disabled). */
+                       reg_dcdcc: dcdcc {
+                               regulator-min-microvolt = <900000>;
+                               regulator-max-microvolt = <900000>;
+                               regulator-name = "vdd-gpu";
+                       };
+
+                       /* 0.9 V (enabled). */
+                       reg_dcdcd: dcdcd {
+                               regulator-boot-on;
+                               regulator-always-on;    /* Hang if disabled. */
+                               regulator-min-microvolt = <900000>;
+                               regulator-max-microvolt = <900000>;

arch/arm/boot/dts/sun9i-a80-cx-a99.dts line 382

Quoted 10 lines
arch/arm/boot/dts/sun9i-a80-cx-a99.dts new file +10 -0
+                               regulator-name = "vdd-sys";
+                       };
+
+                       /* 3.3 V (enabled). */
+                       reg_dcdce: dcdce {
+                               regulator-boot-on;
+                               regulator-always-on;
+                               regulator-min-microvolt = <3300000>;
+                               regulator-max-microvolt = <3300000>;
+                               regulator-name = "vcc-pb-pc-pd-pe-pf-ph-mmc-spdif";

This is probably vcc-io or something shorter.

Regards
ChenYu

Quoted 39 lines
arch/arm/boot/dts/sun9i-a80-cx-a99.dts new file +31 -1
+                       };
+
+                       /* 3.3 V (disabled). */
+                       reg_sw: sw {
+                               regulator-min-microvolt = <3300000>;
+                               regulator-max-microvolt = <3300000>;
+                               regulator-name = "vcc-gmac3v3";
+                       };
+               };
+       };
+};
+
+/*
+ * 5-pin connector opposite of the SD card slot:
+ * 1 = GND (pointed to by small triangle), 2 = GND, 3 = 3.3 V, 4 = RX, 5 = TX.
+ */
+&uart0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&uart0_pins_a>;
+       status = "okay";
+};
+
+/* The port has two Vbus supplies. See workaround at regulator-usb1-1-vbus. */
+&usbphy1 {
+       phy-supply = <&reg_usb1_1_vbus>;
+       status = "okay";
+};
+
+&usbphy3 {
+       status = "okay";
+};
--

2.10.2

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#9 lore raw

Re: [PATCH 3/5] mfd: axp20x: Add support for the AXP808 PMIC

In reply to Chen-Yu Tsai
Quoted 2 lines · Chen-Yu Tsai

On Fri, Jan 27, 2017 at 5:25 AM, Rask Ingemann Lambertsen <[email protected]> wrote:

[...]

Quoted 4 lines
Quoted 4 lines
drivers/mfd/axp20x.c +0 -0
index 25115fe..2d3383e 100644

[...]

Quoted 18 lines
Quoted 18 lines
drivers/mfd/axp20x.c +7 -0
@@ -148,6 +149,13 @@ static const struct regmap_range axp806_writeable_ranges[] = {
        regmap_reg_range(AXP806_REG_ADDR_EXT, AXP806_REG_ADDR_EXT),
 };
 
+static const struct regmap_range axp808_writeable_ranges[] = {
+       regmap_reg_range(AXP20X_DATACACHE(0), AXP20X_DATACACHE(3)),
+       regmap_reg_range(AXP806_PWR_OUT_CTRL1, AXP806_CLDO3_V_CTRL),
+       regmap_reg_range(AXP20X_IRQ1_EN, AXP20X_IRQ2_EN),
+       regmap_reg_range(AXP20X_IRQ1_STATE, AXP20X_IRQ2_STATE),
+};
+
 static const struct regmap_range axp806_volatile_ranges[] = {
        regmap_reg_range(AXP20X_IRQ1_STATE, AXP20X_IRQ2_STATE),
 };
@@ -162,6 +170,11 @@ static const struct regmap_access_table axp806_volatile_table = {
        .n_yes_ranges   = ARRAY_SIZE(axp806_volatile_ranges),
 };
 
Quoted 6 lines

drivers/mfd/axp20x.c static const struct regmap_access_table axp806_volatile_table = { · line 175

Quoted 3 lines
drivers/mfd/axp20x.c +3 -0
+static const struct regmap_access_table axp808_writeable_table = {
+       .yes_ranges     = axp808_writeable_ranges,
+       .n_yes_ranges   = ARRAY_SIZE(axp808_writeable_ranges),

You could probably get away with using axp806_writeable_ranges, and pass ARRAY_SIZE(axp808_writeable_ranges) - 1 for .n_yes_ranges.

Assuming that register ranges not supported on the AXP808 are always at one end of the table, I think it will ease maintenance by avoiding duplicate data should entries be added or removed in the future. I'll put a comment above axp806_writeable_ranges to point out what's going on.

Quoted 1 line

Or maybe the compiler figures out the 2 arrays share common data.

It doesn't as of gcc 6.2.1.

Signature · 1 line
Rask Ingemann Lambertsen
#15 lore raw

Re: [PATCH 5/5] ARM: dts: sun9i: Initial support for the Sunchip CX-A99 board

In reply to Chen-Yu Tsai
Quoted 4 lines · Chen-Yu Tsai

Hi,

On Fri, Jan 27, 2017 at 5:27 AM, Rask Ingemann Lambertsen <[email protected]> wrote:

[...]

Quoted 5 lines
Quoted 5 lines
arch/arm/boot/dts/sun9i-a80-cx-a99.dts new file +0 -0
new file mode 100644
index 0000000..8925093

[...]

Quoted 9 lines

arch/arm/boot/dts/sun9i-a80-cx-a99.dts line 81

Quoted 7 lines
arch/arm/boot/dts/sun9i-a80-cx-a99.dts new file +7 -0
+       leds {
+               compatible = "gpio-leds";
+
+               blue {
+                       gpios = <&pio 6 10 GPIO_ACTIVE_HIGH>;   /* PG10 */
+                       label = "cx-a99:blue:status";
+                       default-state = "on";

Please add a note justifying default-state = "on".

I think I'll remove it instead. The device ships with a U-Boot and Android installation where blue means "on" and red means "stand-by" (which is simply implemented by blanking the screen, it seems), but I doubt many people want to run the rather old Android version available for this device. Instead, I was going to point to the quick setup guide, but it has no mention of the LEDs at all, so I guess the user won't expect the blue LED to turn on.

Quoted 10 lines

arch/arm/boot/dts/sun9i-a80-cx-a99.dts line 106

Quoted 9 lines
arch/arm/boot/dts/sun9i-a80-cx-a99.dts new file +9 -0
+       /* USB 3.0 OTG connector. For now, only Vbus is supported. */
+       reg_usb0_vbus: regulator-usb0-vbus {
+               compatible = "regulator-fixed";
+               regulator-name = "usb0-vbus";
+               regulator-min-microvolt = <5000000>;
+               regulator-max-microvolt = <5000000>;
+               gpio = <&pio 7 15 GPIO_ACTIVE_HIGH>;    /* PH15 */
+               enable-active-high;
+               regulator-always-on;
Quoted 2 lines

It's bad to leave VBUS for OTG connectors on. You never know what is plugged in.

The comment is misleading as the connector is not an OTG one but just a standard-A receptacle wired to the SoC's OTG port. I'll change the comment.

Quoted 7 lines

arch/arm/boot/dts/sun9i-a80-cx-a99.dts line 178

Quoted 5 lines
arch/arm/boot/dts/sun9i-a80-cx-a99.dts new file +5 -0
+/* SD card slot. */
+&mmc0 {
+       bus-width = <4>;
+       cd-gpios = <&pio 7 17 GPIO_ACTIVE_LOW>; /* PH17 */
+       broken-cd;                              /* Interrupts don't work. */

This should be handled by the driver.

The MMC core, without broken-cd, requests the GPIO driver to enable interrupt delivery on the pin and will fall back to polling the GPIO pin if the GPIO driver refuses to enable interrupt delivery. What I see is that the GPIO driver accepts to deliver interrupts, but only the first interrupt is triggered (as evident from /proc/interrupts showing only 1). The vendor sys_config.fex also sets the GPIO pin to polled operation, so maybe there is a hardware bug.

The sunxi-mmc driver doesn't really support operation with broken-cd only because it spams the console and dmesg with useless error messages, see
https://www.mail-archive.com/linux-sunxi at googlegroups.com/msg19963.html for an example.

The comment should probably read something like "GPIO pin delivers no interrupts, poll it".

Quoted 6 lines

arch/arm/boot/dts/sun9i-a80-cx-a99.dts line 281

Quoted 4 lines
arch/arm/boot/dts/sun9i-a80-cx-a99.dts new file +4 -0
+                       /* 1.8 V (enabled). */
+                       reg_bldo1: bldo1 {
+                               regulator-boot-on;
+                               regulator-always-on;    /* Hang if disabled */

If you specify always-on, you don't need to add boot-on.

Ack.

Quoted 9 lines

arch/arm/boot/dts/sun9i-a80-cx-a99.dts line 382

Quoted 7 lines
arch/arm/boot/dts/sun9i-a80-cx-a99.dts new file +7 -0
+                       /* 3.3 V (enabled). */
+                       reg_dcdce: dcdce {
+                               regulator-boot-on;
+                               regulator-always-on;
+                               regulator-min-microvolt = <3300000>;
+                               regulator-max-microvolt = <3300000>;
+                               regulator-name = "vcc-pb-pc-pd-pe-pf-ph-mmc-spdif";

This is probably vcc-io or something shorter.

I'm verbose with the names of the regulators for documentation purposes because unlike some of the boards aimed at developers, documentation is on this device is scarse. I see that with -mmc now added after my latest round of probing with a multimeter, the line went above 80 characters. Will it be OK with vcc-pb,c,d,e,f,h-mmc-spdif?

Signature · 1 line
Rask Ingemann Lambertsen