Add Device Tree for OMAP3 and omap3_logic
Subsystems (5)
v2 cover Add Device Tree for OMAP3 and omap3_logic
This patch series copies the Linux Device trees for the OMAP3 and OMAP3630 platforms as well as some additional device trees to support the Logic PD Torpedo and Logic PD SOM-LV both based on DM3730 (OMAP3630) processors. There are no changes to patches 2-6 from the initial version posted as RFC, but I added "Reviewed-by: Lokesh Vutla <[email protected]>" to patches 2-6
Part 1 Changes the method for the MMC base address offsets to be caluclated. These offsets are different between OMAP3 and am33xx and omap4+. This moves away from an #ifdef method to a method of that uses .compatible to determine the offset. This is needed for OMAP3 device tree support.
This rest of this series allows us move to DM_I2C and DM_MMC and push the DM_SERIAL setup to the OF except when in SPL. This should give enough background for other OMAP3 boards to migrate to device tree.
The dm uclass dump is as follows:
uclass 0: root
- * root_driver @ 8df38028, seq 0, (req -1)
uclass 9: simple_bus
- * ocp at 68000000 @ 8df382e0, seq 0, (req -1)
- l4 at 48000000 @ 8df38348 - scm at 2000 @ 8df383b0 - scm_conf at 270 @ 8df38418
uclass 19: gpio
- gpio_omap @ 8df380b0 - gpio_omap @ 8df38108 - gpio_omap @ 8df38160 - gpio_omap @ 8df381b8 - gpio_omap @ 8df38210 - gpio_omap @ 8df38268 - gpio at 48310000 @ 8df38480 - gpio at 49050000 @ 8df384e8 - gpio at 49052000 @ 8df38550
- * gpio at 49054000 @ 8df385b8, seq 0, (req -1)
- gpio at 49056000 @ 8df38620
- gpio at 49058000 @ 8df38688
uclass 20: i2c
- * i2c at 48070000 @ 8df38880, seq 0, (req 0)
- i2c at 48072000 @ 8df388d8, seq -1, (req 1)
- i2c at 48060000 @ 8df38930, seq -1, (req 2)
uclass 22: i2c_generic
- * generic_4b @ 8df4b178, seq 0, (req -1)
uclass 31: mmc
- * mmc at 4809c000 @ 8df389a8, seq 0, (req -1)
- * mmc at 480ad000 @ 8df38b80, seq 1, (req -1)
uclass 52: serial
- * serial at 4806a000 @ 8df38710, seq 0, (req 0)
- serial at 4806c000 @ 8df38780, seq -1, (req 1) - serial at 49020000 @ 8df387f0, seq -1, (req 2) - serial at 49042000 @ 8df38d58, seq -1, (req 3)
Adam Ford (9):
omap_hsmmc: update struct hsmmc to accommodate omap3 from DT
omap3: Copy Device tree from Linux 4.9.y stable
omap3630: Copy Device tree from Linux 4.9.y stable
ARM: OMAP: I2C: Support New read, write and probe functions for OMAP3
omap3: Copy twl4030 device tree from Linux 4.9.y stable
OMAP3: Add SMSC9221 device tree for omap devices connected on GPMC.
ARM: DTS: Add Logic PD DM3730 SOM-LV initial support
ARM: DTS: Add Logic PD DM3730 Torpedo Device Tree
omap3_logic: Add Device Tree Support and more DM drivers
arch/arm/dts/Makefile | 4 + arch/arm/dts/logicpd-som-lv-37xx-devkit.dts | 269 ++++ arch/arm/dts/logicpd-som-lv.dtsi | 271 ++++ arch/arm/dts/logicpd-torpedo-37xx-devkit.dts | 411 +++++ arch/arm/dts/logicpd-torpedo-som.dtsi | 217 +++ arch/arm/dts/omap-gpmc-smsc9221.dtsi | 58 + arch/arm/dts/omap3.dtsi | 854 ++++++++++ arch/arm/dts/omap34xx-omap36xx-clocks.dtsi | 268 ++++ .../omap36xx-am35xx-omap3430es2plus-clocks.dtsi | 242 +++ arch/arm/dts/omap36xx-clocks.dtsi | 110 ++ arch/arm/dts/omap36xx-omap3430es2plus-clocks.dtsi | 198 +++ arch/arm/dts/omap36xx.dtsi | 118 ++ arch/arm/dts/omap3xxx-clocks.dtsi | 1665 ++++++++++++++++++++ arch/arm/dts/twl4030.dtsi | 161 ++ arch/arm/dts/twl4030_omap3.dtsi | 42 + arch/arm/include/asm/omap_mmc.h | 3 - board/logicpd/omap3som/README | 19 + board/logicpd/omap3som/omap3logic.c | 18 +- configs/omap3_logic_defconfig | 8 +- drivers/i2c/omap24xx_i2c.c | 1 + drivers/mmc/omap_hsmmc.c | 35 +- include/configs/omap3_logic.h | 25 +- include/dt-bindings/media/omap3-isp.h | 22 + 23 files changed, 4993 insertions(+), 26 deletions(-) create mode 100644 arch/arm/dts/logicpd-som-lv-37xx-devkit.dts create mode 100644 arch/arm/dts/logicpd-som-lv.dtsi create mode 100644 arch/arm/dts/logicpd-torpedo-37xx-devkit.dts create mode 100644 arch/arm/dts/logicpd-torpedo-som.dtsi create mode 100644 arch/arm/dts/omap-gpmc-smsc9221.dtsi create mode 100644 arch/arm/dts/omap3.dtsi create mode 100644 arch/arm/dts/omap34xx-omap36xx-clocks.dtsi create mode 100644 arch/arm/dts/omap36xx-am35xx-omap3430es2plus-clocks.dtsi create mode 100644 arch/arm/dts/omap36xx-clocks.dtsi create mode 100644 arch/arm/dts/omap36xx-omap3430es2plus-clocks.dtsi create mode 100644 arch/arm/dts/omap36xx.dtsi create mode 100644 arch/arm/dts/omap3xxx-clocks.dtsi create mode 100644 arch/arm/dts/twl4030.dtsi create mode 100644 arch/arm/dts/twl4030_omap3.dtsi create mode 100644 board/logicpd/omap3som/README create mode 100644 include/dt-bindings/media/omap3-isp.h
Signature · 1 line
2.7.4
PATCH v2 1/9 omap_hsmmc: update struct hsmmc to accommodate omap3 from DT
This patch changes the way DM_MMC calculates offset to the base register of MMC. Previously this was through an #ifdef but that wasn't necessary for OMAP3.
This patch will now add in the offset to the base address based on the .compatible flags.
Signed-off-by Adam Ford <[email protected]>
V2: Remove ifdef completely and reference offset from the omap_hsmmc_ids table.
V1: Change ifdef to ignore OMAP3
arch/arm/include/asm/omap_mmc.h +0 -3
@@ -26,9 +26,6 @@#define OMAP_MMC_H_ struct hsmmc { -#ifdef CONFIG_DM_MMC -unsigned char res0[0x100 ]; -#endif unsigned char res1[0x10 ];unsigned int sysconfig;/* 0x10 */ unsigned int sysstatus;/* 0x14 */
drivers/mmc/omap_hsmmc.c +31 -4
@@ -61,6 +61,10 @@ struct omap_hsmmc_plat {struct mmc mmc; }; +struct omap2_mmc_platform_config { +u32 reg_offset; +}; +struct omap_hsmmc_data {struct hsmmc *base_addr;#ifndef CONFIG_DM_MMC
@@ -778,12 +782,14 @@ static int omap_hsmmc_ofdata_to_platdata(struct udevice *dev)struct omap_hsmmc_data *priv =dev_get_priv (dev);struct omap_hsmmc_plat *plat =dev_get_platdata (dev);struct mmc_config *cfg = &plat->cfg; +struct omap2_mmc_platform_config *data = + (struct omap2_mmc_platform_config *)dev_get_driver_data (dev);const void *fdt = gd->fdt_blob;int node =dev_of_offset (dev);int val; priv->base_addr =map_physmem (dev_get_addr (dev),sizeof (struct hsmmc *), -MAP_NOCACHE ); +MAP_NOCACHE ) + data->reg_offset; cfg->host_caps = MMC_MODE_HS_52MHz |MMC_MODE_HS ; val =fdtdec_get_int (fdt, node,"bus-width" ,-1 );
@@ -854,10 +860,31 @@ static int omap_hsmmc_probe(struct udevice *dev)return 0 ; } +static const struct omap2_mmc_platform_config omap3_mmc_pdata = { + .reg_offset =0 , +}; + +static const struct omap2_mmc_platform_config am33xx_mmc_pdata = { + .reg_offset =0x100 , +}; + +static const struct omap2_mmc_platform_config omap4_mmc_pdata = { + .reg_offset =0x100 , +}; +static const struct udevice_id omap_hsmmc_ids[] = { - { .compatible ="ti,omap3-hsmmc" }, - { .compatible ="ti,omap4-hsmmc" }, - { .compatible ="ti,am33xx-hsmmc" }, + { + .compatible ="ti,omap3-hsmmc" , + .data = (ulong)&omap3_mmc_pdata + }, + { + .compatible ="ti,omap4-hsmmc" , + .data = (ulong)&omap4_mmc_pdata + }, + { + .compatible ="ti,am33xx-hsmmc" , + .data = (ulong)&am33xx_mmc_pdata + }, { } };
Signature · 1 line
2.7.4
PATCH v2 2/9 omap3: Copy Device tree from Linux 4.9.y stable
In reply to Adam FordAdd device tree support to allow for CONFIG_OF_CONTROL in OMAP3 boards.
Signed-off-by Adam Ford <[email protected]>
Reviewed-by Lokesh Vutla <[email protected]>
arch/arm/dts/omap3.dtsi new file +854 -0
@@ -0,0 +1,854 @@ +/* + * Device Tree Source for OMAP3 SoC + * + * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/ + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/pinctrl/omap.h> + +/ { + compatible = "ti,omap3430", "ti,omap3"; + interrupt-parent = <&intc>; + #address-cells = <1>; + #size-cells = <1>; + chosen { }; + + aliases { + i2c0 = &i2c1; + i2c1 = &i2c2; + i2c2 = &i2c3; + serial0 = &uart1; + serial1 = &uart2; + serial2 = &uart3; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu at 0 { + compatible = "arm,cortex-a8"; + device_type = "cpu"; + reg = <0x0>; + + clocks = <&dpll1_ck>; + clock-names = "cpu"; + + clock-latency = <300000>; /* From omap-cpufreq driver */ + }; + }; + + pmu at 54000000 { + compatible = "arm,cortex-a8-pmu"; + reg = <0x54000000 0x800000>; + interrupts = <3>; + ti,hwmods = "debugss"; + }; + + /* + * The soc node represents the soc top level view. It is used for IPs + * that are not memory mapped in the MPU view or for the MPU itself. + */ + soc { + compatible = "ti,omap-infra"; + mpu { + compatible = "ti,omap3-mpu"; + ti,hwmods = "mpu"; + }; + + iva: iva { + compatible = "ti,iva2.2"; + ti,hwmods = "iva"; + + dsp { + compatible = "ti,omap3-c64"; + }; + }; + }; + + /* + * XXX: Use a flat representation of the OMAP3 interconnect. + * The real OMAP interconnect network is quite complex. + * Since it will not bring real advantage to represent that in DT for + * the moment, just use a fake OCP bus entry to represent the whole bus + * hierarchy. + */ + ocp at 68000000 { + compatible = "ti,omap3-l3-smx", "simple-bus"; + reg = <0x68000000 0x10000>; + interrupts = <9 10>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + ti,hwmods = "l3_main"; + + l4_core: l4 at 48000000 { + compatible = "ti,omap3-l4-core", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x48000000 0x1000000>; + + scm: scm at 2000 { + compatible = "ti,omap3-scm", "simple-bus"; + reg = <0x2000 0x2000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x2000 0x2000>; + + omap3_pmx_core: pinmux at 30 { + compatible = "ti,omap3-padconf", + "pinctrl-single"; + reg = <0x30 0x238>; + #address-cells = <1>; + #size-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; + pinctrl-single,register-width = <16>; + pinctrl-single,function-mask = <0xff1f>; + }; + + scm_conf: scm_conf at 270 { + compatible = "syscon", "simple-bus"; + reg = <0x270 0x330>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x270 0x330>; + + pbias_regulator: pbias_regulator at 2b0 { + compatible = "ti,pbias-omap3", "ti,pbias-omap"; + reg = <0x2b0 0x4>; + syscon = <&scm_conf>; + pbias_mmc_reg: pbias_mmc_omap2430 { + regulator-name = "pbias_mmc_omap2430"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + }; + }; + + scm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + scm_clockdomains: clockdomains { + }; + + omap3_pmx_wkup: pinmux at a00 { + compatible = "ti,omap3-padconf", + "pinctrl-single"; + reg = <0xa00 0x5c>; + #address-cells = <1>; + #size-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; + pinctrl-single,register-width = <16>; + pinctrl-single,function-mask = <0xff1f>; + }; + }; + }; + + aes: aes at 480c5000 { + compatible = "ti,omap3-aes"; + ti,hwmods = "aes"; + reg = <0x480c5000 0x50>; + interrupts = <0>; + dmas = <&sdma 65 &sdma 66>; + dma-names = "tx", "rx"; + }; + + prm: prm at 48306000 { + compatible = "ti,omap3-prm"; + reg = <0x48306000 0x4000>; + interrupts = <11>; + + prm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + + prm_clockdomains: clockdomains { + }; + }; + + cm: cm at 48004000 { + compatible = "ti,omap3-cm"; + reg = <0x48004000 0x4000>; + + cm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + + cm_clockdomains: clockdomains { + }; + }; + + counter32k: counter at 48320000 { + compatible = "ti,omap-counter32k"; + reg = <0x48320000 0x20>; + ti,hwmods = "counter_32k"; + }; + + intc: interrupt-controller at 48200000 { + compatible = "ti,omap3-intc"; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x48200000 0x1000>; + }; + + sdma: dma-controller at 48056000 { + compatible = "ti,omap3630-sdma", "ti,omap3430-sdma"; + reg = <0x48056000 0x1000>; + interrupts = <12>, + <13>, + <14>, + <15>; + #dma-cells = <1>; + dma-channels = <32>; + dma-requests = <96>; + }; + + gpio1: gpio at 48310000 { + compatible = "ti,omap3-gpio"; + reg = <0x48310000 0x200>; + interrupts = <29>; + ti,hwmods = "gpio1"; + ti,gpio-always-on; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio2: gpio at 49050000 { + compatible = "ti,omap3-gpio"; + reg = <0x49050000 0x200>; + interrupts = <30>; + ti,hwmods = "gpio2"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio3: gpio at 49052000 { + compatible = "ti,omap3-gpio"; + reg = <0x49052000 0x200>; + interrupts = <31>; + ti,hwmods = "gpio3"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio4: gpio at 49054000 { + compatible = "ti,omap3-gpio"; + reg = <0x49054000 0x200>; + interrupts = <32>; + ti,hwmods = "gpio4"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio5: gpio at 49056000 { + compatible = "ti,omap3-gpio"; + reg = <0x49056000 0x200>; + interrupts = <33>; + ti,hwmods = "gpio5"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio6: gpio at 49058000 { + compatible = "ti,omap3-gpio"; + reg = <0x49058000 0x200>; + interrupts = <34>; + ti,hwmods = "gpio6"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + uart1: serial at 4806a000 { + compatible = "ti,omap3-uart"; + reg = <0x4806a000 0x2000>; + reg-shift = <2>; + interrupts-extended = <&intc 72>; + dmas = <&sdma 49 &sdma 50>; + dma-names = "tx", "rx"; + ti,hwmods = "uart1"; + clock-frequency = <48000000>; + }; + + uart2: serial at 4806c000 { + compatible = "ti,omap3-uart"; + reg = <0x4806c000 0x400>; + interrupts-extended = <&intc 73>; + dmas = <&sdma 51 &sdma 52>; + dma-names = "tx", "rx"; + ti,hwmods = "uart2"; + clock-frequency = <48000000>; + }; + + uart3: serial at 49020000 { + compatible = "ti,omap3-uart"; + reg = <0x49020000 0x400>; + interrupts-extended = <&intc 74>; + dmas = <&sdma 53 &sdma 54>; + dma-names = "tx", "rx"; + ti,hwmods = "uart3"; + clock-frequency = <48000000>; + }; + + i2c1: i2c at 48070000 { + compatible = "ti,omap3-i2c"; + reg = <0x48070000 0x80>; + interrupts = <56>; + dmas = <&sdma 27 &sdma 28>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "i2c1"; + }; + + i2c2: i2c at 48072000 { + compatible = "ti,omap3-i2c"; + reg = <0x48072000 0x80>; + interrupts = <57>; + dmas = <&sdma 29 &sdma 30>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "i2c2"; + }; + + i2c3: i2c at 48060000 { + compatible = "ti,omap3-i2c"; + reg = <0x48060000 0x80>; + interrupts = <61>; + dmas = <&sdma 25 &sdma 26>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "i2c3"; + }; + + mailbox: mailbox at 48094000 { + compatible = "ti,omap3-mailbox"; + ti,hwmods = "mailbox"; + reg = <0x48094000 0x200>; + interrupts = <26>; + #mbox-cells = <1>; + ti,mbox-num-users = <2>; + ti,mbox-num-fifos = <2>; + mbox_dsp: dsp { + ti,mbox-tx = <0 0 0>; + ti,mbox-rx = <1 0 0>; + }; + }; + + mcspi1: spi at 48098000 { + compatible = "ti,omap2-mcspi"; + reg = <0x48098000 0x100>; + interrupts = <65>; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "mcspi1"; + ti,spi-num-cs = <4>; + dmas = <&sdma 35>, + <&sdma 36>, + <&sdma 37>, + <&sdma 38>, + <&sdma 39>, + <&sdma 40>, + <&sdma 41>, + <&sdma 42>; + dma-names = "tx0", "rx0", "tx1", "rx1", + "tx2", "rx2", "tx3", "rx3"; + }; + + mcspi2: spi at 4809a000 { + compatible = "ti,omap2-mcspi"; + reg = <0x4809a000 0x100>; + interrupts = <66>; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "mcspi2"; + ti,spi-num-cs = <2>; + dmas = <&sdma 43>, + <&sdma 44>, + <&sdma 45>, + <&sdma 46>; + dma-names = "tx0", "rx0", "tx1", "rx1"; + }; + + mcspi3: spi at 480b8000 { + compatible = "ti,omap2-mcspi"; + reg = <0x480b8000 0x100>; + interrupts = <91>; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "mcspi3"; + ti,spi-num-cs = <2>; + dmas = <&sdma 15>, + <&sdma 16>, + <&sdma 23>, + <&sdma 24>; + dma-names = "tx0", "rx0", "tx1", "rx1"; + }; + + mcspi4: spi at 480ba000 { + compatible = "ti,omap2-mcspi"; + reg = <0x480ba000 0x100>; + interrupts = <48>; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "mcspi4"; + ti,spi-num-cs = <1>; + dmas = <&sdma 70>, <&sdma 71>; + dma-names = "tx0", "rx0"; + }; + + hdqw1w: 1w at 480b2000 { + compatible = "ti,omap3-1w"; + reg = <0x480b2000 0x1000>; + interrupts = <58>; + ti,hwmods = "hdq1w"; + }; + + mmc1: mmc at 4809c000 { + compatible = "ti,omap3-hsmmc"; + reg = <0x4809c000 0x200>; + interrupts = <83>; + ti,hwmods = "mmc1"; + ti,dual-volt; + dmas = <&sdma 61>, <&sdma 62>; + dma-names = "tx", "rx"; + pbias-supply = <&pbias_mmc_reg>; + }; + + mmc2: mmc at 480b4000 { + compatible = "ti,omap3-hsmmc"; + reg = <0x480b4000 0x200>; + interrupts = <86>; + ti,hwmods = "mmc2"; + dmas = <&sdma 47>, <&sdma 48>; + dma-names = "tx", "rx"; + }; + + mmc3: mmc at 480ad000 { + compatible = "ti,omap3-hsmmc"; + reg = <0x480ad000 0x200>; + interrupts = <94>; + ti,hwmods = "mmc3"; + dmas = <&sdma 77>, <&sdma 78>; + dma-names = "tx", "rx"; + }; + + mmu_isp: mmu at 480bd400 { + #iommu-cells = <0>; + compatible = "ti,omap2-iommu"; + reg = <0x480bd400 0x80>; + interrupts = <24>; + ti,hwmods = "mmu_isp"; + ti,#tlb-entries = <8>; + }; + + mmu_iva: mmu at 5d000000 { + #iommu-cells = <0>; + compatible = "ti,omap2-iommu"; + reg = <0x5d000000 0x80>; + interrupts = <28>; + ti,hwmods = "mmu_iva"; + status = "disabled"; + }; + + wdt2: wdt at 48314000 { + compatible = "ti,omap3-wdt"; + reg = <0x48314000 0x80>; + ti,hwmods = "wd_timer2"; + }; + + mcbsp1: mcbsp at 48074000 { + compatible = "ti,omap3-mcbsp"; + reg = <0x48074000 0xff>; + reg-names = "mpu"; + interrupts = <16>, /* OCP compliant interrupt */ + <59>, /* TX interrupt */ + <60>; /* RX interrupt */ + interrupt-names = "common", "tx", "rx"; + ti,buffer-size = <128>; + ti,hwmods = "mcbsp1"; + dmas = <&sdma 31>, + <&sdma 32>; + dma-names = "tx", "rx"; + clocks = <&mcbsp1_fck>; + clock-names = "fck"; + status = "disabled"; + }; + + mcbsp2: mcbsp at 49022000 { + compatible = "ti,omap3-mcbsp"; + reg = <0x49022000 0xff>, + <0x49028000 0xff>; + reg-names = "mpu", "sidetone"; + interrupts = <17>, /* OCP compliant interrupt */ + <62>, /* TX interrupt */ + <63>, /* RX interrupt */ + <4>; /* Sidetone */ + interrupt-names = "common", "tx", "rx", "sidetone"; + ti,buffer-size = <1280>; + ti,hwmods = "mcbsp2", "mcbsp2_sidetone"; + dmas = <&sdma 33>, + <&sdma 34>; + dma-names = "tx", "rx"; + clocks = <&mcbsp2_fck>, <&mcbsp2_ick>; + clock-names = "fck", "ick"; + status = "disabled"; + }; + + mcbsp3: mcbsp at 49024000 { + compatible = "ti,omap3-mcbsp"; + reg = <0x49024000 0xff>, + <0x4902a000 0xff>; + reg-names = "mpu", "sidetone"; + interrupts = <22>, /* OCP compliant interrupt */ + <89>, /* TX interrupt */ + <90>, /* RX interrupt */ + <5>; /* Sidetone */ + interrupt-names = "common", "tx", "rx", "sidetone"; + ti,buffer-size = <128>; + ti,hwmods = "mcbsp3", "mcbsp3_sidetone"; + dmas = <&sdma 17>, + <&sdma 18>; + dma-names = "tx", "rx"; + clocks = <&mcbsp3_fck>, <&mcbsp3_ick>; + clock-names = "fck", "ick"; + status = "disabled"; + }; + + mcbsp4: mcbsp at 49026000 { + compatible = "ti,omap3-mcbsp"; + reg = <0x49026000 0xff>; + reg-names = "mpu"; + interrupts = <23>, /* OCP compliant interrupt */ + <54>, /* TX interrupt */ + <55>; /* RX interrupt */ + interrupt-names = "common", "tx", "rx"; + ti,buffer-size = <128>; + ti,hwmods = "mcbsp4"; + dmas = <&sdma 19>, + <&sdma 20>; + dma-names = "tx", "rx"; + clocks = <&mcbsp4_fck>; + clock-names = "fck"; + status = "disabled"; + }; + + mcbsp5: mcbsp at 48096000 { + compatible = "ti,omap3-mcbsp"; + reg = <0x48096000 0xff>; + reg-names = "mpu"; + interrupts = <27>, /* OCP compliant interrupt */ + <81>, /* TX interrupt */ + <82>; /* RX interrupt */ + interrupt-names = "common", "tx", "rx"; + ti,buffer-size = <128>; + ti,hwmods = "mcbsp5"; + dmas = <&sdma 21>, + <&sdma 22>; + dma-names = "tx", "rx"; + clocks = <&mcbsp5_fck>; + clock-names = "fck"; + status = "disabled"; + }; + + sham: sham at 480c3000 { + compatible = "ti,omap3-sham"; + ti,hwmods = "sham"; + reg = <0x480c3000 0x64>; + interrupts = <49>; + dmas = <&sdma 69>; + dma-names = "rx"; + }; + + smartreflex_core: smartreflex at 480cb000 { + compatible = "ti,omap3-smartreflex-core"; + ti,hwmods = "smartreflex_core"; + reg = <0x480cb000 0x400>; + interrupts = <19>; + }; + + smartreflex_mpu_iva: smartreflex at 480c9000 { + compatible = "ti,omap3-smartreflex-iva"; + ti,hwmods = "smartreflex_mpu_iva"; + reg = <0x480c9000 0x400>; + interrupts = <18>; + }; + + timer1: timer at 48318000 { + compatible = "ti,omap3430-timer"; + reg = <0x48318000 0x400>; + interrupts = <37>; + ti,hwmods = "timer1"; + ti,timer-alwon; + }; + + timer2: timer at 49032000 { + compatible = "ti,omap3430-timer"; + reg = <0x49032000 0x400>; + interrupts = <38>; + ti,hwmods = "timer2"; + }; + + timer3: timer at 49034000 { + compatible = "ti,omap3430-timer"; + reg = <0x49034000 0x400>; + interrupts = <39>; + ti,hwmods = "timer3"; + }; + + timer4: timer at 49036000 { + compatible = "ti,omap3430-timer"; + reg = <0x49036000 0x400>; + interrupts = <40>; + ti,hwmods = "timer4"; + }; + + timer5: timer at 49038000 { + compatible = "ti,omap3430-timer"; + reg = <0x49038000 0x400>; + interrupts = <41>; + ti,hwmods = "timer5"; + ti,timer-dsp; + }; + + timer6: timer at 4903a000 { + compatible = "ti,omap3430-timer"; + reg = <0x4903a000 0x400>; + interrupts = <42>; + ti,hwmods = "timer6"; + ti,timer-dsp; + }; + + timer7: timer at 4903c000 { + compatible = "ti,omap3430-timer"; + reg = <0x4903c000 0x400>; + interrupts = <43>; + ti,hwmods = "timer7"; + ti,timer-dsp; + }; + + timer8: timer at 4903e000 { + compatible = "ti,omap3430-timer"; + reg = <0x4903e000 0x400>; + interrupts = <44>; + ti,hwmods = "timer8"; + ti,timer-pwm; + ti,timer-dsp; + }; + + timer9: timer at 49040000 { + compatible = "ti,omap3430-timer"; + reg = <0x49040000 0x400>; + interrupts = <45>; + ti,hwmods = "timer9"; + ti,timer-pwm; + }; + + timer10: timer at 48086000 { + compatible = "ti,omap3430-timer"; + reg = <0x48086000 0x400>; + interrupts = <46>; + ti,hwmods = "timer10"; + ti,timer-pwm; + }; + + timer11: timer at 48088000 { + compatible = "ti,omap3430-timer"; + reg = <0x48088000 0x400>; + interrupts = <47>; + ti,hwmods = "timer11"; + ti,timer-pwm; + }; + + timer12: timer at 48304000 { + compatible = "ti,omap3430-timer"; + reg = <0x48304000 0x400>; + interrupts = <95>; + ti,hwmods = "timer12"; + ti,timer-alwon; + ti,timer-secure; + }; + + usbhstll: usbhstll at 48062000 { + compatible = "ti,usbhs-tll"; + reg = <0x48062000 0x1000>; + interrupts = <78>; + ti,hwmods = "usb_tll_hs"; + }; + + usbhshost: usbhshost at 48064000 { + compatible = "ti,usbhs-host"; + reg = <0x48064000 0x400>; + ti,hwmods = "usb_host_hs"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + usbhsohci: ohci at 48064400 { + compatible = "ti,ohci-omap3"; + reg = <0x48064400 0x400>; + interrupt-parent = <&intc>; + interrupts = <76>; + }; + + usbhsehci: ehci at 48064800 { + compatible = "ti,ehci-omap"; + reg = <0x48064800 0x400>; + interrupt-parent = <&intc>; + interrupts = <77>; + }; + }; + + gpmc: gpmc at 6e000000 { + compatible = "ti,omap3430-gpmc"; + ti,hwmods = "gpmc"; + reg = <0x6e000000 0x02d0>; + interrupts = <20>; + dmas = <&sdma 4>; + dma-names = "rxtx"; + gpmc,num-cs = <8>; + gpmc,num-waitpins = <4>; + #address-cells = <2>; + #size-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + }; + + usb_otg_hs: usb_otg_hs at 480ab000 { + compatible = "ti,omap3-musb"; + reg = <0x480ab000 0x1000>; + interrupts = <92>, <93>; + interrupt-names = "mc", "dma"; + ti,hwmods = "usb_otg_hs"; + multipoint = <1>; + num-eps = <16>; + ram-bits = <12>; + }; + + dss: dss at 48050000 { + compatible = "ti,omap3-dss"; + reg = <0x48050000 0x200>; + status = "disabled"; + ti,hwmods = "dss_core"; + clocks = <&dss1_alwon_fck>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + dispc at 48050400 { + compatible = "ti,omap3-dispc"; + reg = <0x48050400 0x400>; + interrupts = <25>; + ti,hwmods = "dss_dispc"; + clocks = <&dss1_alwon_fck>; + clock-names = "fck"; + }; + + dsi: encoder at 4804fc00 { + compatible = "ti,omap3-dsi"; + reg = <0x4804fc00 0x200>, + <0x4804fe00 0x40>, + <0x4804ff00 0x20>; + reg-names = "proto", "phy", "pll"; + interrupts = <25>; + status = "disabled"; + ti,hwmods = "dss_dsi1"; + clocks = <&dss1_alwon_fck>, <&dss2_alwon_fck>; + clock-names = "fck", "sys_clk"; + }; + + rfbi: encoder at 48050800 { + compatible = "ti,omap3-rfbi"; + reg = <0x48050800 0x100>; + status = "disabled"; + ti,hwmods = "dss_rfbi"; + clocks = <&dss1_alwon_fck>, <&dss_ick>; + clock-names = "fck", "ick"; + }; + + venc: encoder at 48050c00 { + compatible = "ti,omap3-venc"; + reg = <0x48050c00 0x100>; + status = "disabled"; + ti,hwmods = "dss_venc"; + clocks = <&dss_tv_fck>; + clock-names = "fck"; + }; + }; + + ssi: ssi-controller at 48058000 { + compatible = "ti,omap3-ssi"; + ti,hwmods = "ssi"; + + status = "disabled"; + + reg = <0x48058000 0x1000>, + <0x48059000 0x1000>; + reg-names = "sys", + "gdd"; + + interrupts = <71>; + interrupt-names = "gdd_mpu"; + + #address-cells = <1>; + #size-cells = <1>; + ranges; + + ssi_port1: ssi-port at 4805a000 { + compatible = "ti,omap3-ssi-port"; + + reg = <0x4805a000 0x800>, + <0x4805a800 0x800>; + reg-names = "tx", + "rx"; + + interrupt-parent = <&intc>; + interrupts = <67>, + <68>; + }; + + ssi_port2: ssi-port at 4805b000 { + compatible = "ti,omap3-ssi-port"; + + reg = <0x4805b000 0x800>, + <0x4805b800 0x800>; + reg-names = "tx", + "rx"; + + interrupt-parent = <&intc>; + interrupts = <69>, + <70>; + }; + }; + }; +}; + +/include/ "omap3xxx-clocks.dtsi"
arch/arm/dts/omap3xxx-clocks.dtsi new file +1665 -0
1,665 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH v2 3/9 omap3630: Copy Device tree from Linux 4.9.y stable
In reply to Adam FordAdd device tree support to allow for CONFIG_OF_CONTROL in OMAP3630 boards. DM3730 can use this same device tree.
Signed-off-by Adam Ford <[email protected]>
Reviewed-by Lokesh Vutla <[email protected]>
arch/arm/dts/omap34xx-omap36xx-clocks.dtsi new file +268 -0
@@ -0,0 +1,268 @@ +/* + * Device Tree Source for OMAP34XX/OMAP36XX clock data + * + * Copyright (C) 2013 Texas Instruments, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +&cm_clocks { + security_l4_ick2: security_l4_ick2 { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&l4_ick>; + clock-mult = <1>; + clock-div = <1>; + }; + + aes1_ick: aes1_ick at a14 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&security_l4_ick2>; + ti,bit-shift = <3>; + reg = <0x0a14>; + }; + + rng_ick: rng_ick at a14 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&security_l4_ick2>; + reg = <0x0a14>; + ti,bit-shift = <2>; + }; + + sha11_ick: sha11_ick at a14 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&security_l4_ick2>; + reg = <0x0a14>; + ti,bit-shift = <1>; + }; + + des1_ick: des1_ick at a14 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&security_l4_ick2>; + reg = <0x0a14>; + ti,bit-shift = <0>; + }; + + cam_mclk: cam_mclk at f00 { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&dpll4_m5x2_ck>; + ti,bit-shift = <0>; + reg = <0x0f00>; + ti,set-rate-parent; + }; + + cam_ick: cam_ick at f10 { + #clock-cells = <0>; + compatible = "ti,omap3-no-wait-interface-clock"; + clocks = <&l4_ick>; + reg = <0x0f10>; + ti,bit-shift = <0>; + }; + + csi2_96m_fck: csi2_96m_fck at f00 { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&core_96m_fck>; + reg = <0x0f00>; + ti,bit-shift = <1>; + }; + + security_l3_ick: security_l3_ick { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&l3_ick>; + clock-mult = <1>; + clock-div = <1>; + }; + + pka_ick: pka_ick at a14 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&security_l3_ick>; + reg = <0x0a14>; + ti,bit-shift = <4>; + }; + + icr_ick: icr_ick at a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + reg = <0x0a10>; + ti,bit-shift = <29>; + }; + + des2_ick: des2_ick at a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + reg = <0x0a10>; + ti,bit-shift = <26>; + }; + + mspro_ick: mspro_ick at a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + reg = <0x0a10>; + ti,bit-shift = <23>; + }; + + mailboxes_ick: mailboxes_ick at a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&core_l4_ick>; + reg = <0x0a10>; + ti,bit-shift = <7>; + }; + + ssi_l4_ick: ssi_l4_ick { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&l4_ick>; + clock-mult = <1>; + clock-div = <1>; + }; + + sr1_fck: sr1_fck at c00 { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&sys_ck>; + reg = <0x0c00>; + ti,bit-shift = <6>; + }; + + sr2_fck: sr2_fck at c00 { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&sys_ck>; + reg = <0x0c00>; + ti,bit-shift = <7>; + }; + + sr_l4_ick: sr_l4_ick { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&l4_ick>; + clock-mult = <1>; + clock-div = <1>; + }; + + dpll2_fck: dpll2_fck at 40 { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&core_ck>; + ti,bit-shift = <19>; + ti,max-div = <7>; + reg = <0x0040>; + ti,index-starts-at-one; + }; + + dpll2_ck: dpll2_ck at 4 { + #clock-cells = <0>; + compatible = "ti,omap3-dpll-clock"; + clocks = <&sys_ck>, <&dpll2_fck>; + reg = <0x0004>, <0x0024>, <0x0040>, <0x0034>; + ti,low-power-stop; + ti,lock; + ti,low-power-bypass; + }; + + dpll2_m2_ck: dpll2_m2_ck at 44 { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&dpll2_ck>; + ti,max-div = <31>; + reg = <0x0044>; + ti,index-starts-at-one; + }; + + iva2_ck: iva2_ck at 0 { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&dpll2_m2_ck>; + reg = <0x0000>; + ti,bit-shift = <0>; + }; + + modem_fck: modem_fck at a00 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&sys_ck>; + reg = <0x0a00>; + ti,bit-shift = <31>; + }; + + sad2d_ick: sad2d_ick at a10 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&l3_ick>; + reg = <0x0a10>; + ti,bit-shift = <3>; + }; + + mad2d_ick: mad2d_ick at a18 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&l3_ick>; + reg = <0x0a18>; + ti,bit-shift = <3>; + }; + + mspro_fck: mspro_fck at a00 { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&core_96m_fck>; + reg = <0x0a00>; + ti,bit-shift = <23>; + }; +}; + +&cm_clockdomains { + cam_clkdm: cam_clkdm { + compatible = "ti,clockdomain"; + clocks = <&cam_ick>, <&csi2_96m_fck>; + }; + + iva2_clkdm: iva2_clkdm { + compatible = "ti,clockdomain"; + clocks = <&iva2_ck>; + }; + + dpll2_clkdm: dpll2_clkdm { + compatible = "ti,clockdomain"; + clocks = <&dpll2_ck>; + }; + + wkup_clkdm: wkup_clkdm { + compatible = "ti,clockdomain"; + clocks = <&gpio1_dbck>, <&wdt2_fck>, <&wdt2_ick>, <&wdt1_ick>, + <&gpio1_ick>, <&omap_32ksync_ick>, <&gpt12_ick>, + <&gpt1_ick>, <&sr1_fck>, <&sr2_fck>; + }; + + d2d_clkdm: d2d_clkdm { + compatible = "ti,clockdomain"; + clocks = <&modem_fck>, <&sad2d_ick>, <&mad2d_ick>; + }; + + core_l4_clkdm: core_l4_clkdm { + compatible = "ti,clockdomain"; + clocks = <&mmchs2_fck>, <&mmchs1_fck>, <&i2c3_fck>, <&i2c2_fck>, + <&i2c1_fck>, <&mcspi4_fck>, <&mcspi3_fck>, + <&mcspi2_fck>, <&mcspi1_fck>, <&uart2_fck>, + <&uart1_fck>, <&hdq_fck>, <&mmchs2_ick>, <&mmchs1_ick>, + <&hdq_ick>, <&mcspi4_ick>, <&mcspi3_ick>, + <&mcspi2_ick>, <&mcspi1_ick>, <&i2c3_ick>, <&i2c2_ick>, + <&i2c1_ick>, <&uart2_ick>, <&uart1_ick>, <&gpt11_ick>, + <&gpt10_ick>, <&mcbsp5_ick>, <&mcbsp1_ick>, + <&omapctrl_ick>, <&aes2_ick>, <&sha12_ick>, <&icr_ick>, + <&des2_ick>, <&mspro_ick>, <&mailboxes_ick>, + <&mspro_fck>; + }; +};
arch/arm/dts/omap36xx-am35xx-omap3430es2plus-clocks.dtsi new file +242 -0
242 lines not on this page · raw message
arch/arm/dts/omap36xx-clocks.dtsi new file +110 -0
110 lines not on this page · raw message
arch/arm/dts/omap36xx-omap3430es2plus-clocks.dtsi new file +198 -0
198 lines not on this page · raw message
arch/arm/dts/omap36xx.dtsi new file +118 -0
118 lines not on this page · raw message
include/dt-bindings/media/omap3-isp.h new file +22 -0
@@ -0,0 +1,22 @@ +/* +* include/dt-bindings/media/omap3-isp.h +* +* Copyright (C) 2015 Sakari Ailus +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License +* version 2 as published by the Free Software Foundation. +* +* This program is distributed in the hope that it will be useful, but +* WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU +* General Public License for more details. +*/ + +#ifndef __DT_BINDINGS_OMAP3_ISP_H__ +#define __DT_BINDINGS_OMAP3_ISP_H__ + +#define OMAP3ISP_PHY_TYPE_COMPLEX_IO 0 +#define OMAP3ISP_PHY_TYPE_CSIPHY 1 + +#endif /* __DT_BINDINGS_OMAP3_ISP_H__ */
Signature · 1 line
2.7.4
PATCH v2 4/9 ARM: OMAP: I2C: Support New read, write and probe functions for OMAP3
In reply to Adam FordNew i2c_read, i2c_write and i2c_probe functions, tested on OMAP4 (4430/60/70), OMAP5 (5430) and AM335X (3359) were added in 960187ffa125( "ARM: OMAP: I2C: New read, write and probe functions") but not tested on OMAP3. This patch will allow the updated drivers using device tree and DM_I2C to operate on OMAP3.
Signed-off-by Adam Ford <[email protected]>
Reviewed-by Lokesh Vutla <[email protected]>
drivers/i2c/omap24xx_i2c.c +1 -0
@@ -910,6 +910,7 @@ static const struct dm_i2c_ops omap_i2c_ops = { };static const struct udevice_id omap_i2c_ids[] = { + { .compatible ="ti,omap3-i2c" }, { .compatible ="ti,omap4-i2c" }, { } };
Signature · 1 line
2.7.4
PATCH v2 5/9 omap3: Copy twl4030 device tree from Linux 4.9.y stable
In reply to Adam FordMany OMAP3 boards use a TWL4030 PMIC. This brings in the related device tree information for common TWL4030 and TWL4030 with OMAP3.
Signed-off-by Adam Ford <[email protected]>
Reviewed-by Lokesh Vutla <[email protected]>
arch/arm/dts/twl4030.dtsi new file +161 -0
@@ -0,0 +1,161 @@ +/* + * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* + * Integrated Power Management Chip + */ +&twl { + compatible = "ti,twl4030"; + interrupt-controller; + #interrupt-cells = <1>; + + rtc { + compatible = "ti,twl4030-rtc"; + interrupts = <11>; + }; + + charger: bci { + compatible = "ti,twl4030-bci"; + interrupts = <9>, <2>; + bci3v1-supply = <&vusb3v1>; + }; + + watchdog { + compatible = "ti,twl4030-wdt"; + }; + + vaux1: regulator-vaux1 { + compatible = "ti,twl4030-vaux1"; + }; + + vaux2: regulator-vaux2 { + compatible = "ti,twl4030-vaux2"; + }; + + vaux3: regulator-vaux3 { + compatible = "ti,twl4030-vaux3"; + }; + + vaux4: regulator-vaux4 { + compatible = "ti,twl4030-vaux4"; + }; + + vcc: regulator-vdd1 { + compatible = "ti,twl4030-vdd1"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1450000>; + }; + + vdac: regulator-vdac { + compatible = "ti,twl4030-vdac"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vio: regulator-vio { + compatible = "ti,twl4030-vio"; + }; + + vintana1: regulator-vintana1 { + compatible = "ti,twl4030-vintana1"; + }; + + vintana2: regulator-vintana2 { + compatible = "ti,twl4030-vintana2"; + }; + + vintdig: regulator-vintdig { + compatible = "ti,twl4030-vintdig"; + }; + + vmmc1: regulator-vmmc1 { + compatible = "ti,twl4030-vmmc1"; + regulator-min-microvolt = <1850000>; + regulator-max-microvolt = <3150000>; + }; + + vmmc2: regulator-vmmc2 { + compatible = "ti,twl4030-vmmc2"; + regulator-min-microvolt = <1850000>; + regulator-max-microvolt = <3150000>; + }; + + vusb1v5: regulator-vusb1v5 { + compatible = "ti,twl4030-vusb1v5"; + }; + + vusb1v8: regulator-vusb1v8 { + compatible = "ti,twl4030-vusb1v8"; + }; + + vusb3v1: regulator-vusb3v1 { + compatible = "ti,twl4030-vusb3v1"; + }; + + vpll1: regulator-vpll1 { + compatible = "ti,twl4030-vpll1"; + }; + + vpll2: regulator-vpll2 { + compatible = "ti,twl4030-vpll2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vsim: regulator-vsim { + compatible = "ti,twl4030-vsim"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + }; + + twl_gpio: gpio { + compatible = "ti,twl4030-gpio"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + usb2_phy: twl4030-usb { + compatible = "ti,twl4030-usb"; + interrupts = <10>, <4>; + usb1v5-supply = <&vusb1v5>; + usb1v8-supply = <&vusb1v8>; + usb3v1-supply = <&vusb3v1>; + usb_mode = <1>; + #phy-cells = <0>; + }; + + twl_pwm: pwm { + compatible = "ti,twl4030-pwm"; + #pwm-cells = <2>; + }; + + twl_pwmled: pwmled { + compatible = "ti,twl4030-pwmled"; + #pwm-cells = <2>; + }; + + twl_pwrbutton: pwrbutton { + compatible = "ti,twl4030-pwrbutton"; + interrupts = <8>; + }; + + twl_keypad: keypad { + compatible = "ti,twl4030-keypad"; + interrupts = <1>; + keypad,num-rows = <8>; + keypad,num-columns = <8>; + }; + + twl_madc: madc { + compatible = "ti,twl4030-madc"; + interrupts = <3>; + #io-channel-cells = <1>; + }; +};
arch/arm/dts/twl4030_omap3.dtsi new file +42 -0
42 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH v2 6/9 OMAP3: Add SMSC9221 device tree for omap devices connected on GPMC.
In reply to Adam FordSome OMAP3 devices support an SMSC ethernet PHY connected to the GPMC bus. This copies this device tree from Linux 4.9.y stable
Signed-off-by Adam Ford <[email protected]>
Reviewed-by Lokesh Vutla <[email protected]>
arch/arm/dts/omap-gpmc-smsc9221.dtsi new file +58 -0
@@ -0,0 +1,58 @@ +/* + * Common file for GPMC connected smsc9221 on omaps + * + * Compared to smsc911x, smsc9221 (and others like smsc9217 + * or smsc 9218) has faster timings, leading to higher + * bandwidth. + * + * Note that the board specifc DTS file needs to specify + * ranges, pinctrl, reg, interrupt parent and interrupts. + */ + +/ { + vddvario: regulator-vddvario { + compatible = "regulator-fixed"; + regulator-name = "vddvario"; + regulator-always-on; + }; + + vdd33a: regulator-vdd33a { + compatible = "regulator-fixed"; + regulator-name = "vdd33a"; + regulator-always-on; + }; +}; + +&gpmc { + ethernet at gpmc { + compatible = "smsc,lan9221","smsc,lan9115"; + bank-width = <2>; + + gpmc,mux-add-data; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <42>; + gpmc,cs-wr-off-ns = <36>; + gpmc,adv-on-ns = <6>; + gpmc,adv-rd-off-ns = <12>; + gpmc,adv-wr-off-ns = <12>; + gpmc,oe-on-ns = <0>; + gpmc,oe-off-ns = <42>; + gpmc,we-on-ns = <0>; + gpmc,we-off-ns = <36>; + gpmc,rd-cycle-ns = <60>; + gpmc,wr-cycle-ns = <54>; + gpmc,access-ns = <36>; + gpmc,page-burst-access-ns = <0>; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <0>; + gpmc,wr-data-mux-bus-ns = <18>; + gpmc,wr-access-ns = <42>; + gpmc,cycle2cycle-samecsen; + gpmc,cycle2cycle-diffcsen; + + vddvario-supply = <&vddvario>; + vdd33a-supply = <&vdd33a>; + reg-io-width = <4>; + smsc,save-mac-address; + }; +};
Signature · 1 line
2.7.4
PATCH v2 7/9 ARM: DTS: Add Logic PD DM3730 SOM-LV initial support
In reply to Adam FordThis adds the device tree. Previous commit added both boards at the same time.
Signed-off-by Adam Ford <[email protected]>
Changes in V2:
Split the SOM-LV from Torpedo
arch/arm/dts/logicpd-som-lv-37xx-devkit.dts new file +269 -0
@@ -0,0 +1,269 @@ +/* + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; + +#include "omap36xx.dtsi" +#include "logicpd-som-lv.dtsi" +#include "omap-gpmc-smsc9221.dtsi" + +/ { + model = "LogicPD Zoom DM3730 SOM-LV Development Kit"; + compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3630", "ti,omap3"; + + chosen { + stdout-path = &uart1; + }; + + gpio_keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_key_pins>; + + sysboot2 { + label = "gpio3"; + gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* gpio_111 / uP_GPIO_3 */ + linux,code = <BTN_0>; + wakeup-source; + }; + }; + + sound { + compatible = "ti,omap-twl4030"; + ti,model = "omap3logic"; + ti,mcbsp = <&mcbsp2>; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins &led_pins_wkup>; + + led1 { + label = "led1"; + gpios = <&gpio5 5 GPIO_ACTIVE_LOW>; /* gpio133 */ + linux,default-trigger = "cpu0"; + }; + + led2 { + label = "led2"; + gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; /* gpio11 */ + linux,default-trigger = "none"; + }; + }; +}; + +&vaux1 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; +}; + +&vaux4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; +}; + +&mcbsp2 { + status = "okay"; +}; + +&charger { + ti,bb-uvolt = <3200000>; + ti,bb-uamp = <150>; +}; + +&gpmc { + ranges = <1 0 0x08000000 0x1000000>; /* CS1: 16MB for LAN9221 */ + + ethernet at gpmc { + pinctrl-names = "default"; + pinctrl-0 = <&lan9221_pins>; + interrupt-parent = <&gpio5>; + interrupts = <24 IRQ_TYPE_LEVEL_LOW>; /* gpio_152 */ + reg = <1 0 0xff>; + }; +}; + +&vpll2 { + regulator-always-on; +}; + +&dss { + status = "ok"; + vdds_dsi-supply = <&vpll2>; + vdda_video-supply = <&video_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&dss_dpi_pins1>; + port { + dpi_out: endpoint { + remote-endpoint = <&lcd_in>; + data-lines = <16>; + }; + }; +}; + +/ { + aliases { + display0 = &lcd0; + }; + + video_reg: video_reg { + compatible = "regulator-fixed"; + regulator-name = "fixed-supply"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + lcd0: display at 0 { + compatible = "panel-dpi"; + label = "28"; + status = "okay"; + /* default-on; */ + pinctrl-names = "default"; + pinctrl-0 = <&lcd_enable_pin>; + enable-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd INI */ + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + + panel-timing { + clock-frequency = <9000000>; + hactive = <480>; + vactive = <272>; + hfront-porch = <3>; + hback-porch = <2>; + hsync-len = <42>; + vback-porch = <3>; + vfront-porch = <2>; + vsync-len = <11>; + hsync-active = <1>; + vsync-active = <1>; + de-active = <1>; + pixelclk-active = <0>; + }; + }; + + bl: backlight { + compatible = "pwm-backlight"; + pinctrl-names = "default"; + pinctrl-0 = <&backlight_pins>; + pwms = <&twl_pwm 0 5000000>; + brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; + default-brightness-level = <7>; + enable-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; /* gpio_8 */ + }; +}; + +&mmc1 { + interrupts-extended = <&intc 83 &omap3_pmx_core 0x11a>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + vmmc-supply = <&vmmc1>; + bus-width = <4>; + cap-power-off-card; +}; + +&mmc2 { + status = "disabled"; +}; + +&omap3_pmx_core { + gpio_key_pins: pinmux_gpio_key_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x212e, PIN_INPUT_PULLUP | MUX_MODE4) /* cam_xclkb.gpio_111 / uP_GPIO_3*/ + >; + }; + + led_pins: pinmux_led_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x215e, PIN_OUTPUT_PULLUP | MUX_MODE4) /* sdmmc2_dat1.gpio_133 / uP_GPIO_0 */ + >; + }; + + lan9221_pins: pinmux_lan9221_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */ + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ + OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ + OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ + OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ + OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ + OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ + OMAP3_CORE1_IOPAD(0x2132, PIN_INPUT_PULLUP | MUX_MODE4) /* cam_strobe.gpio_126 */ + OMAP3_CORE1_IOPAD(0x212c, PIN_INPUT_PULLUP | MUX_MODE4) /* cam_d11.gpio_110 */ + >; + }; + + lcd_enable_pin: pinmux_lcd_enable_pin { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* mcbsp4_fs.gpio_155 */ + >; + }; + + dss_dpi_pins1: pinmux_dss_dpi_pins1 { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_pclk.dss_pclk */ + OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_hsync.dss_hsync */ + OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_vsync.dss_vsync */ + OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_acbias.dss_acbias */ + + OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data0.dss_data0 */ + OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data1.dss_data1 */ + OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data2.dss_data2 */ + OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data3.dss_data3 */ + OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data4.dss_data4 */ + OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data5.dss_data5 */ + OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data6.dss_data6 */ + OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data7.dss_data7 */ + OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data8.dss_data8 */ + OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data9.dss_data9 */ + OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data10.dss_data10 */ + OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data11.dss_data11 */ + OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data12.dss_data12 */ + OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data13.dss_data13 */ + OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data14.dss_data14 */ + OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data15.dss_data15 */ + >; + }; +}; + +&omap3_pmx_wkup { + led_pins_wkup: pinmux_led_pins_wkup { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a24, PIN_OUTPUT_PULLUP | MUX_MODE4) /* jtag_emu0.gpio_11 / uP_GPIO_1 */ + >; + }; + + backlight_pins: pinmux_backlight_pins { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a16, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* sys_boot6.gpio_8 */ + >; + }; +}; + + +&uart1 { + interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>; +}; + +/* Wired to the tps65950 on the SOM, only the USB connector is on the devkit */ +&usb_otg_hs { + pinctrl-names = "default"; + pinctrl-0 = <&hsusb_otg_pins>; + interface-type = <0>; + usb-phy = <&usb2_phy>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; + mode = <3>; + power = <50>; +};
arch/arm/dts/logicpd-som-lv.dtsi new file +271 -0
271 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH v2 8/9 ARM: DTS: Add Logic PD DM3730 Torpedo Device Tree
In reply to Adam FordPrevious commit has this combined with SOM-LV. This commit has only the Torpedo Device Tree.
The device trees were sync'd with 4.9.y stable with two changes:
disable mmc2 and stdout-path = &uart1. Both of those two changes will be submitted to the linux-omap list
Signed-off-by Adam Ford <[email protected]>
Changes in V2:
Split device tree from other board
arch/arm/dts/logicpd-torpedo-37xx-devkit.dts new file +411 -0
@@ -0,0 +1,411 @@ +/* + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; + +#include "omap36xx.dtsi" +#include "logicpd-torpedo-som.dtsi" +#include "omap-gpmc-smsc9221.dtsi" + +/ { + model = "LogicPD Zoom DM3730 Torpedo + Wireless Development Kit"; + compatible = "logicpd,dm3730-torpedo-devkit", "ti,omap3630", "ti,omap3"; + + chosen { + stdout-path = &uart1; + }; + + gpio_keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_key_pins &gpio_key_pins_wkup>; + + sysboot2 { + label = "sysboot2"; + gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; /* gpio2 */ + linux,code = <BTN_0>; + wakeup-source; + }; + + sysboot5 { + label = "sysboot5"; + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; /* gpio7 */ + linux,code = <BTN_1>; + wakeup-source; + }; + + gpio1 { + label = "gpio1"; + gpios = <&gpio6 21 GPIO_ACTIVE_LOW>; /* gpio181 */ + linux,code = <BTN_2>; + wakeup-source; + }; + + gpio2 { + label = "gpio2"; + gpios = <&gpio6 18 GPIO_ACTIVE_LOW>; /* gpio178 */ + linux,code = <BTN_3>; + wakeup-source; + }; + }; + + sound { + compatible = "ti,omap-twl4030"; + ti,model = "omap3logic"; + ti,mcbsp = <&mcbsp2>; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins>; + + led1 { + label = "led1"; + gpios = <&gpio6 20 GPIO_ACTIVE_HIGH>; /* gpio180 */ + linux,default-trigger = "cpu0"; + }; + + led2 { + label = "led2"; + gpios = <&gpio6 19 GPIO_ACTIVE_HIGH>; /* gpio179 */ + linux,default-trigger = "none"; + }; + }; + + pwm10: dmtimer-pwm { + compatible = "ti,omap-dmtimer-pwm"; + pinctrl-names = "default"; + pinctrl-0 = <&pwm_pins>; + ti,timers = <&timer10>; + #pwm-cells = <3>; + }; + +}; + +&vaux1 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; +}; + +&vaux4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; +}; + +&mcbsp2 { + status = "okay"; +}; + +&charger { + ti,bb-uvolt = <3200000>; + ti,bb-uamp = <150>; +}; + +&gpmc { + ranges = <0 0 0x30000000 0x1000000 /* CS0: 16MB for NAND */ + 1 0 0x2c000000 0x1000000>; /* CS1: 16MB for LAN9221 */ + + ethernet at gpmc { + pinctrl-names = "default"; + pinctrl-0 = <&lan9221_pins>; + interrupt-parent = <&gpio5>; + interrupts = <1 IRQ_TYPE_LEVEL_LOW>; /* gpio129 */ + reg = <1 0 0xff>; + }; +}; + +&vpll2 { + regulator-always-on; +}; + +&dss { + status = "ok"; + vdds_dsi-supply = <&vpll2>; + vdda_video-supply = <&video_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&dss_dpi_pins1>; + port { + dpi_out: endpoint { + remote-endpoint = <&lcd_in>; + data-lines = <16>; + }; + }; +}; + +/ { + aliases { + display0 = &lcd0; + }; + + video_reg: video_reg { + pinctrl-names = "default"; + pinctrl-0 = <&panel_pwr_pins>; + compatible = "regulator-fixed"; + regulator-name = "fixed-supply"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd INI */ + }; + + lcd0: display { + compatible = "panel-dpi"; + label = "15"; + status = "okay"; + /* default-on; */ + pinctrl-names = "default"; + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + + panel-timing { + clock-frequency = <9000000>; + hactive = <480>; + vactive = <272>; + hfront-porch = <3>; + hback-porch = <2>; + hsync-len = <42>; + vback-porch = <3>; + vfront-porch = <4>; + vsync-len = <11>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + }; + + bl: backlight { + compatible = "pwm-backlight"; + pinctrl-names = "default"; + pinctrl-0 = <&backlight_pins>; + pwms = <&pwm10 0 5000000 0>; + brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; + default-brightness-level = <7>; + enable-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH>; /* gpio_154 */ + }; +}; + +&mmc1 { + interrupts-extended = <&intc 83 &omap3_pmx_core 0x11a>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins &mmc1_cd>; + vmmc-supply = <&vmmc1>; + bus-width = <4>; + cap-power-off-card; +}; + +&mmc2 { + status = "disabled"; +}; + +&omap3_pmx_core { + gpio_key_pins: pinmux_gpio_key_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLUP | MUX_MODE4) /* mcspi2_clk.gpio_178 */ + OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLUP | MUX_MODE4) /* mcspi2_cs0.gpio_181 */ + >; + }; + + pwm_pins: pinmux_pwm_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20B8, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* gpmc_ncs5.gpt_10_pwm_evt */ + >; + }; + + led_pins: pinmux_led_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21d8, PIN_OUTPUT | MUX_MODE4) /* gpio_179 */ + OMAP3_CORE1_IOPAD(0x21da, PIN_OUTPUT | MUX_MODE4) /* gpio_180 */ + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ + OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ + OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ + OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ + OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ + OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ + >; + }; + + tsc2004_pins: pinmux_tsc2004_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE4) /* mcbsp4_dr.gpio_153 */ + >; + }; + + backlight_pins: pinmux_backlight_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2188, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* mcbsp4_dx.gpio_154 */ + >; + }; + + isp_pins: pinmux_isp_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x210c, PIN_INPUT | MUX_MODE0) /* cam_hs.cam_hs */ + OMAP3_CORE1_IOPAD(0x210e, PIN_INPUT | MUX_MODE0) /* cam_vs.cam_vs */ + OMAP3_CORE1_IOPAD(0x2110, PIN_INPUT | MUX_MODE0) /* cam_xclka.cam_xclka */ + OMAP3_CORE1_IOPAD(0x2112, PIN_INPUT | MUX_MODE0) /* cam_pclk.cam_pclk */ + + OMAP3_CORE1_IOPAD(0x2114, PIN_INPUT | MUX_MODE0) /* cam_d0.cam_d0 */ + OMAP3_CORE1_IOPAD(0x2116, PIN_INPUT | MUX_MODE0) /* cam_d1.cam_d1 */ + OMAP3_CORE1_IOPAD(0x2118, PIN_INPUT | MUX_MODE0) /* cam_d2.cam_d2 */ + OMAP3_CORE1_IOPAD(0x211c, PIN_INPUT | MUX_MODE0) /* cam_d3.cam_d3 */ + OMAP3_CORE1_IOPAD(0x211e, PIN_INPUT | MUX_MODE0) /* cam_d4.cam_d4 */ + OMAP3_CORE1_IOPAD(0x2120, PIN_INPUT | MUX_MODE0) /* cam_d5.cam_d5 */ + OMAP3_CORE1_IOPAD(0x2122, PIN_INPUT | MUX_MODE0) /* cam_d6.cam_d6 */ + OMAP3_CORE1_IOPAD(0x2124, PIN_INPUT | MUX_MODE0) /* cam_d7.cam_d7 */ + >; + }; + + panel_pwr_pins: pinmux_panel_pwr_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* mcbsp4_fs.gpio_155 */ + >; + }; + + dss_dpi_pins1: pinmux_dss_dpi_pins1 { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_pclk.dss_pclk */ + OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_hsync.dss_hsync */ + OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_vsync.dss_vsync */ + OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_acbias.dss_acbias */ + + OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data6.dss_data6 */ + OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data7.dss_data7 */ + OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data8.dss_data8 */ + OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data9.dss_data9 */ + OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data10.dss_data10 */ + OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data11.dss_data11 */ + OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data12.dss_data12 */ + OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data13.dss_data13 */ + OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data14.dss_data14 */ + OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data15.dss_data15 */ + OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data16.dss_data16 */ + OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data17.dss_data17 */ + + OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data18.dss_data0 */ + OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data19.dss_data1 */ + OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data20.dss_data2 */ + OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data21.dss_data3 */ + OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data22.dss_data4 */ + OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data23.dss_data5 */ + >; + }; +}; + +&omap3_pmx_wkup { + gpio_key_pins_wkup: pinmux_gpio_key_pins_wkup { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a0a, PIN_INPUT_PULLUP | MUX_MODE4) /* sys_boot0.gpio_2 */ + OMAP3_WKUP_IOPAD(0x2a14, PIN_INPUT_PULLUP | MUX_MODE4) /* sys_boot5.gpio_7 */ + >; + }; + + lan9221_pins: pinmux_lan9221_pins { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a5a, PIN_INPUT | MUX_MODE4) /* reserved.gpio_129 */ + >; + }; + + mmc1_cd: pinmux_mmc1_cd { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a54, PIN_INPUT_PULLUP | MUX_MODE4) /* reserved.gpio_127 */ + >; + }; +}; + +&i2c2 { + mt9p031 at 48 { + compatible = "aptina,mt9p031"; + reg = <0x48>; + clocks = <&isp 0>; + vaa-supply = <&vaux4>; + vdd-supply = <&vaux4>; + vdd_io-supply = <&vaux4>; + port { + mt9p031_out: endpoint { + input-clock-frequency = <24000000>; + pixel-clock-frequency = <72000000>; + remote-endpoint = <&ccdc_ep>; + }; + }; + }; +}; + +&i2c3 { + touchscreen: tsc2004 at 48 { + compatible = "ti,tsc2004"; + reg = <0x48>; + vio-supply = <&vaux1>; + pinctrl-names = "default"; + pinctrl-0 = <&tsc2004_pins>; + interrupts-extended = <&gpio5 25 IRQ_TYPE_EDGE_RISING>; /* gpio 153 */ + + touchscreen-fuzz-x = <4>; + touchscreen-fuzz-y = <7>; + touchscreen-fuzz-pressure = <2>; + touchscreen-size-x = <4096>; + touchscreen-size-y = <4096>; + touchscreen-max-pressure = <2048>; + + ti,x-plate-ohms = <280>; + ti,esd-recovery-timeout-ms = <8000>; + }; +}; + +&mcspi1 { + at25 at 0 { + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <5000000>; + spi-cpha; + spi-cpol; + + pagesize = <64>; + size = <32768>; + address-width = <16>; + }; +}; + +&isp { + pinctrl-names = "default"; + pinctrl-0 = <&isp_pins>; + ports { + port at 0 { + reg = <0>; + ccdc_ep: endpoint { + remote-endpoint = <&mt9p031_out>; + bus-width = <8>; + hsync-active = <1>; + vsync-active = <1>; + pclk-sample = <0>; + }; + }; + }; +}; + +&uart1 { + interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>; +}; + +/* Wired to the tps65950 on the SOM, only the USB connector is on the devkit */ +&usb_otg_hs { + pinctrl-names = "default"; + pinctrl-0 = <&hsusb_otg_pins>; + interface-type = <0>; + usb-phy = <&usb2_phy>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; + mode = <3>; + power = <50>; +};
arch/arm/dts/logicpd-torpedo-som.dtsi new file +217 -0
217 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH v2 9/9 omap3_logic: Add Device Tree Support and more DM drivers
In reply to Adam FordThis patch also removes all the excessive code for NS16550 intiailization as the device tree can do that now. This also adds DM_I2C and DM_MMC since the overlying drivers have the built-in support already. The corresponding include/config/omap3_logic.h also reduced in size due to the new device tree support.
Signed-off-by Adam Ford <[email protected]>
Changes in V2:
Retain Auto-detect ability between SOM-LV and Torpedo Split this off from the device sub submissions
arch/arm/dts/Makefile +4 -0
@@ -341,6 +341,10 @@ dtb-$(CONFIG_SOC_KEYSTONE) += keystone-k2hk-evm.dtb \ keystone-k2e-evm.dtb \ keystone-k2g-evm.dtb +dtb-$(CONFIG_TARGET_OMAP3_LOGIC) += \ + logicpd-torpedo-37xx-devkit.dtb \ + logicpd-som-lv-37xx-devkit.dts + dtb-$(CONFIG_TARGET_SAMA5D2_XPLAINED) += \ at91-sama5d2_xplained.dtb
board/logicpd/omap3som/README new file +19 -0
@@ -0,0 +1,19 @@ +Summary +======= + +The source for omap3som encompases the DM3730 SOM-LV and DM3730 Torpedo platforms. + +By default, the Torpedo Device Tree is integrated into U-Boot,but the MMC controller, GPIO and I2C controllers are the same, so for the purposes of loading U-Boot, it should be sufficient. However this will display the Model as "LogicPD Zoom DM3730 Torpedo + Wireless Development Kit" upon boot. + +The actual board remains autodetected and the Board will read "DM37xx SOM LV" when used on the DM37 SOM-LV. The device tree loaded with Linux is also correct. + +Integrating the SOM-LV Device Tree into U-Boot +============================================== + +This step is optional, but should you want to change the default to the SOM-LV, locate the configs/omap3_logic_defconfig file and make the following change. + + CONFIG_DEFAULT_DEVICE_TREE="logicpd-som-lv-37xx-devkit" + + make distclean + make omap3_logic_defconfig +
board/logicpd/omap3som/omap3logic.c +8 -10
@@ -36,16 +36,8 @@DECLARE_GLOBAL_DATA_PTR ; -#define CONTROL_WKUP_CTRL 0x48002a5c -#define GPIO_IO_PWRDNZ (1 << 6) -#define PBIASLITEVMODE1 (1 << 8) - -/* -* two dimensional array of strucures containining board name and Linux -* machine IDs; row it selected based on CPU column is slected based -* on hsusb0_data5 pin having a pulldown resistor -*/ - +/* This is only needed until SPL gets OF support */ +#ifdef CONFIG_SPL_BUILD static const struct ns16550_platdata omap3logic_serial = { .base =OMAP34XX_UART1 , .reg_shift = 2,
@@ -57,7 +49,13 @@ U_BOOT_DEVICE(omap3logic_uart) = {"ns16550_serial" , &omap3logic_serial }; +#endif +/* +* two dimensional array of strucures containining board name and Linux +* machine IDs; row it selected based on CPU column is slected based +* on hsusb0_data5 pin having a pulldown resistor +*/ static struct board_id { char *name; int machine_id;
configs/omap3_logic_defconfig +7 -1
@@ -3,6 +3,8 @@ CONFIG_OMAP34XX=y CONFIG_SYS_MALLOC_F_LEN=0x2000 CONFIG_TARGET_OMAP3_LOGIC=y CONFIG_SPL_STACK_R_ADDR=0x82000000 +CONFIG_DEFAULT_DEVICE_TREE="logicpd-torpedo-37xx-devkit" +CONFIG_FIT=y CONFIG_SYS_EXTRA_OPTIONS="NAND" CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_VERSION_VARIABLE=y
@@ -36,6 +38,11 @@ CONFIG_CMD_FS_GENERIC=y CONFIG_CMD_UBI=y CONFIG_ISO_PARTITION=y CONFIG_EFI_PARTITION=y +CONFIG_OF_CONTROL=y +# CONFIG_BLK is not set +CONFIG_DM_I2C=y +CONFIG_DM_MMC=y +# CONFIG_DM_MMC_OPS is not set CONFIG_MMC_OMAP_HS=y CONFIG_MMC_OMAP36XX_PINS=y CONFIG_SYS_NS16550=y
@@ -46,4 +53,3 @@ CONFIG_USB_GADGET_DOWNLOAD=y CONFIG_G_DNL_MANUFACTURER="TI" CONFIG_G_DNL_VENDOR_NUM=0x0451 CONFIG_G_DNL_PRODUCT_NUM=0xd022 -CONFIG_OF_LIBFDT=y
include/configs/omap3_logic.h +17 -8
@@ -17,12 +17,28 @@#include <configs/ti_omap3_common.h> +#ifdef CONFIG_SPL_BUILD +/* +* Disable MMC DM for SPL build and can be re-enabled after adding +* DM support in SPL +*/ +#undef CONFIG_DM_MMC +#undef OMAP_HSMMC_USE_GPIO + +/* select serial console configuration for SPL */ +#undef CONFIG_CONS_INDEX +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1 +#endif + +/* * We are only ever GP parts and will utilize all of the "downloaded image" * area in SRAM which starts at 0x40200000 and ends at 0x4020FFFF (64KB) in * order to allow for BCH8 to fit in. */ #undef CONFIG_SPL_TEXT_BASE +#define CONFIG_SPL_FRAMEWORK #define CONFIG_SPL_TEXT_BASE 0x40200000#define CONFIG_MISC_INIT_R /* misc_init_r dumps the die id */
@@ -34,16 +50,11 @@/* Hardware drivers */ /* GPIO banks */ +#define CONFIG_OMAP3_GPIO_4 /* GPIO 96..128 is in GPIO bank 4 */ #define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */ #define CONFIG_USB_OMAP3 -/* select serial console configuration */ -#undef CONFIG_CONS_INDEX -#define CONFIG_CONS_INDEX 1 -#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1 -#define CONFIG_SERIAL1 1/* UART1 on OMAP Logic boards */ -/* commands to include */ #define CONFIG_CMD_NAND #define CONFIG_CMD_MTDPARTS
@@ -52,8 +63,6 @@/* I2C */ #define CONFIG_SYS_I2C_OMAP34XX #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50/* EEPROM AT24C64 */ -#define EXPANSION_EEPROM_I2C_BUS 2/* I2C Bus for AT24C64 */ -#define CONFIG_OMAP3_LOGIC_USE_NEW_PRODUCT_ID /* USB */ #define CONFIG_USB_MUSB_OMAP2PLUS
Signature · 1 line
2.7.4
PATCH v2 1/9 omap_hsmmc: update struct hsmmc to accommodate omap3 from DT
In reply to Adam FordQuoted 7 lines · Adam Ford
This patch changes the way
DM_MMCcalculates offset to the base register of MMC. Previously this was through an #ifdef but that wasn't necessary for OMAP3.This patch will now add in the offset to the base address based on the .compatible flags.
Signed-off-by Adam Ford <[email protected]>
Reviewed-by Lokesh Vutla <[email protected]>
Thanks and regards,
Lokesh
PATCH v2 1/9 omap_hsmmc: update struct hsmmc to accommodate omap3 from DT
Quoted 9 lines · Lokesh Vutla
Quoted 6 lines · Adam Ford
This patch changes the way
DM_MMCcalculates offset to the base register of MMC. Previously this was through an #ifdef but that wasn't necessary for OMAP3.This patch will now add in the offset to the base address based on the .compatible flags.
Quoted 7 lines
Quoted 1 line
Signed-off-by Adam Ford <[email protected]>Reviewed-by Lokesh Vutla <[email protected]>Thanks and regards,
Lokesh
Reviewed-by Simon Glass <[email protected]>
PATCH v2 1/9 omap_hsmmc: update struct hsmmc to accommodate omap3 from DT
In reply to Adam Fordarch/arm/include/asm/omap_mmc.h
Quoted 16 lines · Adam Ford
This patch changes the way
DM_MMCcalculates offset to the base register of MMC. Previously this was through an #ifdef but that wasn't necessary for OMAP3.This patch will now add in the offset to the base address based on the .compatible flags.
Signed-off-by Adam Ford <[email protected]>V2: Remove ifdef completely and reference offset from the
omap_hsmmc_idstable.V1: Change ifdef to ignore OMAP3
Reviewed-by Lokesh Vutla <[email protected]>Reviewed-by Simon Glass <[email protected]>arch/arm/include/asm/omap_mmc.h +0
-0
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170510/ed5c0729/attachment.sig>
PATCH v2 2/9 omap3: Copy Device tree from Linux 4.9.y stable
In reply to Adam Fordarch/arm/dts/omap3.dtsi
Quoted 8 lines · Adam Ford
Add device tree support to allow for
CONFIG_OF_CONTROLin OMAP3 boards.Signed-off-by Adam Ford <[email protected]>Reviewed-by Lokesh Vutla <[email protected]>arch/arm/dts/omap3.dtsi new file +0
-0
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170510/fc1435b9/attachment.sig>
PATCH v2 3/9 omap3630: Copy Device tree from Linux 4.9.y stable
In reply to Adam Fordarch/arm/dts/omap34xx-omap36xx-clocks.dtsi
Quoted 9 lines · Adam Ford
Add device tree support to allow for
CONFIG_OF_CONTROLin OMAP3630 boards. DM3730 can use this same device tree.Signed-off-by Adam Ford <[email protected]>Reviewed-by Lokesh Vutla <[email protected]>arch/arm/dts/omap34xx-omap36xx-clocks.dtsi new file +0
-0
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170510/5f896c5a/attachment.sig>
PATCH v2 4/9 ARM: OMAP: I2C: Support New read, write and probe functions for OMAP3
In reply to Adam Forddrivers/i2c/omap24xx_i2c.c
Quoted 11 lines · Adam Ford
New
i2c_read,i2c_writeandi2c_probefunctions, tested on OMAP4 (4430/60/70), OMAP5 (5430) and AM335X (3359) were added in 960187ffa125( "ARM: OMAP: I2C: New read, write and probe functions") but not tested on OMAP3. This patch will allow the updated drivers using device tree andDM_I2Cto operate on OMAP3.Signed-off-by Adam Ford <[email protected]>Reviewed-by Lokesh Vutla <[email protected]>drivers/i2c/omap24xx_i2c.c +0
-0
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170510/efe75286/attachment.sig>
PATCH v2 5/9 omap3: Copy twl4030 device tree from Linux 4.9.y stable
In reply to Adam Fordarch/arm/dts/twl4030.dtsi
Quoted 9 lines · Adam Ford
Many OMAP3 boards use a TWL4030 PMIC. This brings in the related device tree information for common TWL4030 and TWL4030 with OMAP3.
Signed-off-by Adam Ford <[email protected]>Reviewed-by Lokesh Vutla <[email protected]>arch/arm/dts/twl4030.dtsi new file +0
-0
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170510/cfba70dd/attachment.sig>
PATCH v2 6/9 OMAP3: Add SMSC9221 device tree for omap devices connected on GPMC.
In reply to Adam Fordarch/arm/dts/omap-gpmc-smsc9221.dtsi
Quoted 9 lines · Adam Ford
Some OMAP3 devices support an SMSC ethernet PHY connected to the GPMC bus. This copies this device tree from Linux 4.9.y stable
Signed-off-by Adam Ford <[email protected]>Reviewed-by Lokesh Vutla <[email protected]>arch/arm/dts/omap-gpmc-smsc9221.dtsi new file +0
-0
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170510/d14bb648/attachment.sig>
PATCH v2 7/9 ARM: DTS: Add Logic PD DM3730 SOM-LV initial support
In reply to Adam Fordarch/arm/dts/logicpd-som-lv-37xx-devkit.dts
Quoted 11 lines · Adam Ford
This adds the device tree. Previous commit added both boards at the same time.
Signed-off-by Adam Ford <[email protected]>Changes in V2:
Split the SOM-LV from Torpedoarch/arm/dts/logicpd-som-lv-37xx-devkit.dts new file +0
-0
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170510/2a9083bd/attachment.sig>
PATCH v2 8/9 ARM: DTS: Add Logic PD DM3730 Torpedo Device Tree
In reply to Adam Fordarch/arm/dts/logicpd-torpedo-37xx-devkit.dts
Quoted 15 lines · Adam Ford
Previous commit has this combined with SOM-LV. This commit has only the Torpedo Device Tree.
The device trees were sync'd with 4.9.y stable with two changes:
disable mmc2 and stdout-path = &uart1. Both of those two changes will be submitted to the linux-omap listSigned-off-by Adam Ford <[email protected]>Changes in V2:
Split device tree from other boardarch/arm/dts/logicpd-torpedo-37xx-devkit.dts new file +0
-0
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170510/35a4c060/attachment.sig>
PATCH v2 9/9 omap3_logic: Add Device Tree Support and more DM drivers
In reply to Adam Fordarch/arm/dts/Makefile
Quoted 14 lines · Adam Ford
This patch also removes all the excessive code for NS16550 intiailization as the device tree can do that now. This also adds
DM_I2CandDM_MMCsince the overlying drivers have the built-in support already. The correspondinginclude/config/omap3_logic.halso reduced in size due to the new device tree support.Signed-off-by Adam Ford <[email protected]>Changes in V2:
Retain Auto-detect ability between SOM-LV and Torpedo Split this off from the device sub submissionsarch/arm/dts/Makefile +0
-0
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170510/30b6bd19/attachment.sig>