Skip to contentSkip to conversation

net-next: mediatek: add support for ethernet on MT7622 SoC

PATCH Superseded [email protected] 4 participants 10 messages Jul 12, 2017 – Jul 15, 2017

Subsystems (5)

v1 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

cover net-next: mediatek: add support for ethernet on MT7622 SoC

From: Sean Wang <[email protected]>

The series adds the driver for ethernet controller found on MT7622 SoC. There are additions against with previous MT7623 SoC such as shared SGMII given for the dual GMACs and built-in 5-ports 10/100 embedded switch support (ESW). Thus more clocks consumers and SGMII hardware setup for the extra features are all introduced here and as for the support for ESW that would be planned to add in the separate patch integrating with DSA infrastructure in the future.

Currently testing successfully is done with those patches for the conditions such as GMAC2 with IP1001 PHY via RGMII and GMAC1/2 with RTL8211F PHY via SGMII.

Sean Wang (4):
dt-bindings: net: mediatek: add support for MediaTek MT7623 and MT7622
SoC
net-next: mediatek: add platform data to adapt into various hardware
net-next: mediatek: add support for MediaTek MT7622 SoC
MAINTAINERS: add Sean/Nelson as MediaTek ethernet maintainers

 .../devicetree/bindings/net/mediatek-net.txt       |  12 +-
 MAINTAINERS                                        |   2 +
 drivers/net/ethernet/mediatek/Kconfig              |   6 +-
 drivers/net/ethernet/mediatek/mtk_eth_soc.c        | 143 +++++++++++++++++++--
 drivers/net/ethernet/mediatek/mtk_eth_soc.h        |  73 ++++++++++-
 5 files changed, 216 insertions(+), 20 deletions(-)
Signature · 1 line
2.7.4
#1 lore raw

PATCH 1/4 dt-bindings: net: mediatek: add support for MediaTek MT7623 and MT7622 SoC

From: Sean Wang <[email protected]>

The patch adds the supplements in the dt-binding document for MediaTek MT7622 SoC with extra SGMII system controller and relevant clock consumers listed as the requirements for those SoCs equipped with the SGMII circuit. Also, add the missing binding information for MT7623 SoC here which relies on the fallback binding of MT2701.

---
 Documentation/devicetree/bindings/net/mediatek-net.txt | 12 +++++++++---
 1 file changed, 9 insertions(+), 3 deletions(-)
Documentation/devicetree/bindings/net/mediatek-net.txt +9 -3
index c7194e8..1d1168b 100644
@@ -7,24 +7,30 @@ have dual GMAC each represented by a child node..
 * Ethernet controller node
 
 Required properties:
-- compatible: Should be "mediatek,mt2701-eth"
+- compatible: Should be
+		"mediatek,mt2701-eth": for MT2701 SoC
+		"mediatek,mt7623-eth", "mediatek,mt2701-eth": for MT7623 SoC
+		"mediatek,mt7622-eth": for MT7622 SoC
 - reg: Address and length of the register set for the device
 - interrupts: Should contain the three frame engines interrupts in numeric
 	order. These are fe_int0, fe_int1 and fe_int2.
 - clocks: the clock used by the core
 - clock-names: the names of the clock listed in the clocks property. These are
-	"ethif", "esw", "gp2", "gp1"
+	"ethif", "esw", "gp2", "gp1" : For MT2701 and MT7623 SoC
+        "ethif", "esw", "gp0", "gp1", "gp2", "sgmii_tx250m", "sgmii_rx250m",
+	"sgmii_cdr_ref", "sgmii_cdr_fb", "sgmii_ck", "eth2pll" : For MT7622 SoC
 - power-domains: phandle to the power domain that the ethernet is part of
 - resets: Should contain a phandle to the ethsys reset signal
 - reset-names: Should contain the reset signal name "eth"
 - mediatek,ethsys: phandle to the syscon node that handles the port setup
+- mediatek,sgmiisys: phandle to the syscon node that handles the SGMII setup
+	which is required for those SoCs equipped with SGMII such as MT7622 SoC.
 - mediatek,pctl: phandle to the syscon node that handles the ports slew rate
 	and driver current
 
 Optional properties:
 - interrupt-parent: Should be the phandle for the interrupt controller
   that services interrupts for this device
-
 * Ethernet MAC node
 
 Required properties:
Signature · 1 line
2.7.4
#2 lore raw

PATCH 2/4 net-next: mediatek: add platform data to adapt into various hardware

In reply to [email protected]

From: Sean Wang <sean.wang-NuS5LvNUpcJWk0Htik3J/[email protected]>

This patch is the preparation patch in order to adapt into various hardware through adding platform data which holds specific characteristics among MediaTek SoCs and introducing the unified clock handler for those distinct clock requirements depending on different features such as TRGMII and SGMII getting support on the target SoC. And finally, add enhancement with given the generic description for Kconfig and remove the unnecessary machine type dependency in Makefile.

---
 drivers/net/ethernet/mediatek/Kconfig       |  6 +--
 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 71 ++++++++++++++++++++++++-----
 drivers/net/ethernet/mediatek/mtk_eth_soc.h | 23 +++++++++-
 3 files changed, 85 insertions(+), 15 deletions(-)
drivers/net/ethernet/mediatek/Kconfig +3 -3
index 698bb89..f9149d2 100644
@@ -7,11 +7,11 @@ config NET_VENDOR_MEDIATEK
 if NET_VENDOR_MEDIATEK
 
 config NET_MEDIATEK_SOC
-	tristate "MediaTek MT7623 Gigabit ethernet support"
-	depends on NET_VENDOR_MEDIATEK && (MACH_MT7623 || MACH_MT2701)
+	tristate "MediaTek SoC Gigabit Ethernet support"
+	depends on NET_VENDOR_MEDIATEK
 	select PHYLIB
 	---help---
 	  This driver supports the gigabit ethernet MACs in the
-	  MediaTek MT2701/MT7623 chipset family.
+	  MediaTek SoC family.
 
 endif #NET_VENDOR_MEDIATEK
drivers/net/ethernet/mediatek/mtk_eth_soc.c +60 -11

120 lines not on this page · raw message

drivers/net/ethernet/mediatek/mtk_eth_soc.h +22 -1
index 5868a09..8ade23df 100644
@@ -443,6 +443,9 @@ enum mtk_clks_map {
 	MTK_CLK_MAX
 };
 
+#define MT7623_CLKS_BITMAP	(BIT(MTK_CLK_ETHIF) | BIT(MTK_CLK_ESW) |  \
+				 BIT(MTK_CLK_GP1) | BIT(MTK_CLK_GP2) | \
+				 BIT(MTK_CLK_TRGPLL))
 enum mtk_dev_state {
 	MTK_HW_INIT,
 	MTK_RESETTING
@@ -511,6 +514,21 @@ struct mtk_rx_ring {
 	u32 crx_idx_reg;
 };
 
+#define MTK_TRGMII			BIT(0)
+#define MTK_GMAC1_TRGMII		(BIT(1) | MTK_TRGMII)
+#define MTK_HAS_CAPS(caps, _x)		(((caps) & (_x)) == (_x))
+
+/* struct mtk_soc_data -	This is the structure holding all differences
+ *				among various plaforms
+ * @caps			Flags shown the extra capability for the SoC
+ * @required_clks		Flags shown the bitmap for required clocks on
+ *				the target SoC
+ */
+struct mtk_soc_data {
+	u32		caps;
+	u32		required_clks;
+};
+
 /* currently no SoC has more than 2 macs */
 #define MTK_MAX_DEVS			2
 
@@ -542,7 +560,8 @@ struct mtk_rx_ring {
  * @clks:		clock array for all clocks required
  * @mii_bus:		If there is a bus we need to create an instance for it
  * @pending_work:	The workqueue used to reset the dma ring
- * @state               Initialization and runtime state of the device.
+ * @state		Initialization and runtime state of the device
+ * @soc:		Holding specific data among vaious SoCs
  */
 
 struct mtk_eth {
@@ -574,6 +593,8 @@ struct mtk_eth {
 	struct mii_bus			*mii_bus;
 	struct work_struct		pending_work;
 	unsigned long			state;
+
+	const struct mtk_soc_data	*soc;
 };
 
 /* struct mtk_mac -	the structure that holds the info about the MACs of the
Signature · 1 line
2.7.4
#6 lore raw

PATCH 3/4 net-next: mediatek: add support for MediaTek MT7622 SoC

In reply to [email protected]

From: Sean Wang <sean.wang-NuS5LvNUpcJWk0Htik3J/[email protected]>

This patch adds the driver for ethernet controller on MT7622 SoC. It has the similar handling logic as the previously MT7623 does, but there are additions against with MT7623 SoC, the shared SGMII given for the dual GMACs and including 5-ports 10/100 embedded switch support (ESW) as the GMAC1 option, thus more clocks consumers for the extra feature are introduced here. So for ease portability and maintenance, those differences all are being kept inside the platform data as other drivers usually do. Currently testing successfully is done with those patches for the conditions such as GMAC2 with IP1001 PHY via RGMII and GMAC1/2 with RTL8211F PHY via SGMII.

---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 72 ++++++++++++++++++++++++++++-
 drivers/net/ethernet/mediatek/mtk_eth_soc.h | 54 +++++++++++++++++++++-
 2 files changed, 122 insertions(+), 4 deletions(-)
drivers/net/ethernet/mediatek/mtk_eth_soc.c +70 -2
index 51ca79f..e3dbea1 100644
@@ -52,7 +52,8 @@ static const struct mtk_ethtool_stats {
 };
 
 static const char * const mtk_clks_source_name[] = {
-	"ethif", "esw", "gp1", "gp2", "trgpll"
+	"ethif", "esw", "gp0", "gp1", "gp2", "trgpll", "sgmii_tx250m",
+	"sgmii_rx250m", "sgmii_cdr_ref", "sgmii_cdr_fb", "sgmii_ck", "eth2pll"
 };
 
 void mtk_w32(struct mtk_eth *eth, u32 val, unsigned reg)
@@ -162,6 +163,47 @@ static void mtk_gmac0_rgmii_adjust(struct mtk_eth *eth, int speed)
 	mtk_w32(eth, val, TRGMII_TCK_CTRL);
 }
 
+static void mtk_gmac_sgmii_hw_setup(struct mtk_eth *eth, int mac_id)
+{
+	u32 val;
+
+	/* Setup the link timer and QPHY power up inside SGMIISYS */
+	regmap_write(eth->sgmiisys, SGMSYS_PCS_LINK_TIMER,
+		     SGMII_LINK_TIMER_DEFAULT);
+
+	regmap_read(eth->sgmiisys, SGMSYS_SGMII_MODE, &val);
+	val |= SGMII_REMOTE_FAULT_DIS;
+	regmap_write(eth->sgmiisys, SGMSYS_SGMII_MODE, val);
+
+	regmap_read(eth->sgmiisys, SGMSYS_PCS_CONTROL_1, &val);
+	val |= SGMII_AN_RESTART;
+	regmap_write(eth->sgmiisys, SGMSYS_PCS_CONTROL_1, val);
+
+	regmap_read(eth->sgmiisys, SGMSYS_QPHY_PWR_STATE_CTRL, &val);
+	val &= ~SGMII_PHYA_PWD;
+	regmap_write(eth->sgmiisys, SGMSYS_QPHY_PWR_STATE_CTRL, val);
+
+	/* Determine MUX for which GMAC uses the SGMII interface */
+	if (MTK_HAS_CAPS(eth->soc->caps, MTK_DUAL_GMAC_SHARED_SGMII)) {
+		regmap_read(eth->ethsys, ETHSYS_SYSCFG0, &val);
+		val &= ~SYSCFG0_SGMII_MASK;
+		val |= !mac_id ? SYSCFG0_SGMII_GMAC1 : SYSCFG0_SGMII_GMAC2;
+		regmap_write(eth->ethsys, ETHSYS_SYSCFG0, val);
+
+		dev_info(eth->dev, "setup shared sgmii for gmac=%d\n",
+			 mac_id);
+	}
+
+	/* Setup the GMAC1 going through SGMII path when SoC also support
+	 * ESW on GMAC1
+	 */
+	if (MTK_HAS_CAPS(eth->soc->caps, MTK_GMAC1_ESW | MTK_GMAC1_SGMII) &&
+	    !mac_id) {
+		mtk_w32(eth, 0, MTK_MAC_MISC);
+		dev_info(eth->dev, "setup gmac1 going through sgmii");
+	}
+}
+
 static void mtk_phy_link_adjust(struct net_device *dev)
 {
 	struct mtk_mac *mac = netdev_priv(dev);
@@ -269,6 +311,7 @@ static int mtk_phy_connect(struct net_device *dev)
 	if (!np)
 		return -ENODEV;
 
+	mac->ge_mode = 0;
 	switch (of_get_phy_mode(np)) {
 	case PHY_INTERFACE_MODE_TRGMII:
 		mac->trgmii = true;
@@ -276,7 +319,15 @@ static int mtk_phy_connect(struct net_device *dev)
 	case PHY_INTERFACE_MODE_RGMII_RXID:
 	case PHY_INTERFACE_MODE_RGMII_ID:
 	case PHY_INTERFACE_MODE_RGMII:
-		mac->ge_mode = 0;
+		break;
+	case PHY_INTERFACE_MODE_SGMII:
+		if (MTK_HAS_CAPS(eth->soc->caps, MTK_SGMII))
+			mtk_gmac_sgmii_hw_setup(eth, mac->id);
+		break;
+	case PHY_INTERFACE_MODE_INTERNAL:
+		if (MTK_HAS_CAPS(eth->soc->caps, MTK_GMAC1_ESW) && !mac->id)
+			/* Setup the path through ESW internal switch */
+			mtk_w32(eth, MTK_MUX_TO_ESW, MTK_MAC_MISC);
 		break;
 	case PHY_INTERFACE_MODE_MII:
 		mac->ge_mode = 1;
@@ -2424,6 +2475,7 @@ static int mtk_get_chip_id(struct mtk_eth *eth, u32 *chip_id)
 static bool mtk_is_hwlro_supported(struct mtk_eth *eth)
 {
 	switch (eth->chip_id) {
+	case MT7622_ETH:
 	case MT7623_ETH:
 		return true;
 	}
@@ -2463,6 +2515,16 @@ static int mtk_probe(struct platform_device *pdev)
 		return PTR_ERR(eth->ethsys);
 	}
 
+	if (MTK_HAS_CAPS(eth->soc->caps, MTK_SGMII)) {
+		eth->sgmiisys =
+		syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
+						"mediatek,sgmiisys");
+		if (IS_ERR(eth->sgmiisys)) {
+			dev_err(&pdev->dev, "no sgmiisys regmap found\n");
+			return PTR_ERR(eth->sgmiisys);
+		}
+	}
+
 	eth->pctl = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
 						    "mediatek,pctl");
 	if (IS_ERR(eth->pctl)) {
@@ -2596,6 +2658,11 @@ static const struct mtk_soc_data mt2701_data = {
 	.required_clks = MT7623_CLKS_BITMAP
 };
 
+static const struct mtk_soc_data mt7622_data = {
+	.caps = MTK_DUAL_GMAC_SHARED_SGMII | MTK_GMAC1_ESW,
+	.required_clks = MT7622_CLKS_BITMAP
+};
+
 static const struct mtk_soc_data mt7623_data = {
 	.caps = MTK_GMAC1_TRGMII,
 	.required_clks = MT7623_CLKS_BITMAP
@@ -2603,6 +2670,7 @@ static const struct mtk_soc_data mt7623_data = {
 
 const struct of_device_id of_mtk_match[] = {
 	{ .compatible = "mediatek,mt2701-eth", .data = &mt2701_data},
+	{ .compatible = "mediatek,mt7622-eth", .data = &mt7622_data},
 	{ .compatible = "mediatek,mt7623-eth", .data = &mt7623_data},
 	{},
 };
drivers/net/ethernet/mediatek/mtk_eth_soc.h +52 -2

118 lines not on this page · raw message

Signature · 1 line
2.7.4
#8 lore raw

PATCH 4/4 MAINTAINERS: add Sean/Nelson as MediaTek ethernet maintainers

In reply to [email protected]

From: Sean Wang <[email protected]>

Sean and Nelson work for MediaTek on maintaining the MediaTek ethernet driver for the existing SoCs and adding support for the following SoCs. In the past, Sean has been active at making most of the qualifications , stress test and submitting a lot of patches for the driver while Nelson was looking into the aspects more on hardware additions and details such as introducing PDMA with Hardware LRO to the driver.

---
 MAINTAINERS | 2 ++
 1 file changed, 2 insertions(+)
MAINTAINERS +2 -0
index 4f4057c..3b2dd4b 100644
@@ -8385,6 +8385,8 @@ F:	include/uapi/linux/uvcvideo.h
 MEDIATEK ETHERNET DRIVER
 M:	Felix Fietkau <[email protected]>
 M:	John Crispin <[email protected]>
+M:	Sean Wang <[email protected]>
+M:	Nelson Chang <[email protected]>
 L:	[email protected]
 S:	Maintained
 F:	drivers/net/ethernet/mediatek/
Signature · 1 line
2.7.4
maintainer
#9 lore raw
In reply to [email protected]

From: <[email protected]>
Date: Wed, 12 Jul 2017 11:37:41 +0800

Quoted 10 lines

From: Sean Wang <[email protected]>

The series adds the driver for ethernet controller found on MT7622 SoC. There are additions against with previous MT7623 SoC such as shared SGMII given for the dual GMACs and built-in 5-ports 10/100 embedded switch support (ESW). Thus more clocks consumers and SGMII hardware setup for the extra features are all introduced here and as for the support for ESW that would be planned to add in the separate patch integrating with DSA infrastructure in the future.

Quoted 2 lines

Currently testing successfully is done with those patches for the conditions such as GMAC2 with IP1001 PHY via RGMII and GMAC1/2 with RTL8211F PHY via SGMII.

net-next is closed, please resubmit this when net-next is open again:

http://vger.kernel.org/~davem/net-next.html

Thanks.

#3 lore raw

Re: [PATCH net-next 2/4] net-next: mediatek: add platform data to adapt into various hardware

In reply to [email protected]
Quoted 16 lines · On 07/11/2017 08:37 PM, [email protected] wrote:

From: Sean Wang <[email protected]>

This patch is the preparation patch in order to adapt into various hardware through adding platform data which holds specific characteristics among MediaTek SoCs and introducing the unified clock handler for those distinct clock requirements depending on different features such as TRGMII and SGMII getting support on the target SoC. And finally, add enhancement with given the generic description for Kconfig and remove the unnecessary machine type dependency in Makefile.

---

drivers/net/ethernet/mediatek/mtk_eth_soc.c +0 -0
 	if (dev->phydev->link)
@@ -1837,6 +1838,39 @@ static void ethsys_reset(struct mtk_eth *eth, u32 reset_bits)
 	mdelay(10);

drivers/net/ethernet/mediatek/mtk_eth_soc.c static void ethsys_reset(struct mtk_eth *eth, u32 reset_bits) · line 1848

Quoted 10 lines
drivers/net/ethernet/mediatek/mtk_eth_soc.c +8 -0
 }
 
+static void mtk_clk_disable(struct mtk_eth *eth)
+{
+	int clk;
+
+	for (clk = MTK_CLK_MAX - 1; clk >= 0; clk--) {
+		if (eth->clks[clk])
+			clk_disable_unprepare(eth->clks[clk]);
+	}

The clock framework works just fine with NULL clk references, no need to check that.

Review static void ethsys_reset(struct mtk_eth *eth, u32 reset_bits) · line 1849

Quoted 1 line
(quoted diff) +1 -0
+}

There are now (or will be soon in clk-next) bulk accessors that you may consider using for this.

drivers/net/ethernet/mediatek/mtk_eth_soc.c static void ethsys_reset(struct mtk_eth *eth, u32 reset_bits) · line 1861

Quoted 12 lines
drivers/net/ethernet/mediatek/mtk_eth_soc.c +12 -0
+
+static int mtk_clk_enable(struct mtk_eth *eth)
+{
+	int clk, ret;
+
+	for (clk = 0; clk < MTK_CLK_MAX ; clk++) {
+		if (eth->clks[clk]) {
+			ret = clk_prepare_enable(eth->clks[clk]);
+			if (ret)
+				goto err_disable_clks;
+		}
+	}

Same here.

Signature · 1 line
Florian
#4 lore raw

Re: [PATCH net-next 2/4] net-next: mediatek: add platform data to adapt into various hardware

In reply to [email protected]
Quoted 28 lines
drivers/net/ethernet/mediatek/mtk_eth_soc.c +23 -0
+static int mtk_clk_enable(struct mtk_eth *eth)
+{
+	int clk, ret;
+
+	for (clk = 0; clk < MTK_CLK_MAX ; clk++) {
+		if (eth->clks[clk]) {
+			ret = clk_prepare_enable(eth->clks[clk]);
+			if (ret)
+				goto err_disable_clks;
+		}
+	}
+
+	return 0;
+
+err_disable_clks:
+	while (--clk >= 0) {
+		if (eth->clks[clk])
+			clk_disable_unprepare(eth->clks[clk]);
+	}
+
+	return ret;
+}
 
+
 static int mtk_hw_init(struct mtk_eth *eth)
 {
 	int i, val;

drivers/net/ethernet/mediatek/mtk_eth_soc.c static int mtk_hw_init(struct mtk_eth *eth) · line 1885

Quoted 9 lines
drivers/net/ethernet/mediatek/mtk_eth_soc.c +2 -4
@@ -1847,10 +1881,8 @@ static int mtk_hw_init(struct mtk_eth *eth)
 	pm_runtime_enable(eth->dev);
 	pm_runtime_get_sync(eth->dev);
 
-	clk_prepare_enable(eth->clks[MTK_CLK_ETHIF]);
-	clk_prepare_enable(eth->clks[MTK_CLK_ESW]);
-	clk_prepare_enable(eth->clks[MTK_CLK_GP1]);
-	clk_prepare_enable(eth->clks[MTK_CLK_GP2]);
+	mtk_clk_enable(eth);
+

mtk_clk_enable() returns an error code. It is probably a good idea to use it, especially if it could be EPRODE_DEFER.

Andrew

#7 lore raw

Re: [PATCH net-next 3/4] net-next: mediatek: add support for MediaTek MT7622 SoC

In reply to [email protected]

Hi Sean

Quoted 16 lines

static void mtk_phy_link_adjust(struct net_device *dev) {

drivers/net/ethernet/mediatek/mtk_eth_soc.c +1 -1
 	struct mtk_mac *mac = netdev_priv(dev);
@@ -269,6 +311,7 @@ static int mtk_phy_connect(struct net_device *dev)
 	if (!np)
 		return -ENODEV;
 
+	mac->ge_mode = 0;
 	switch (of_get_phy_mode(np)) {
 	case PHY_INTERFACE_MODE_TRGMII:
 		mac->trgmii = true;
@@ -276,7 +319,15 @@ static int mtk_phy_connect(struct net_device *dev)
 	case PHY_INTERFACE_MODE_RGMII_RXID:
 	case PHY_INTERFACE_MODE_RGMII_ID:
 	case PHY_INTERFACE_MODE_RGMII:
-		mac->ge_mode = 0;

drivers/net/ethernet/mediatek/mtk_eth_soc.c static int mtk_phy_connect(struct net_device *dev) · line 331

Quoted 10 lines
drivers/net/ethernet/mediatek/mtk_eth_soc.c +9 -0
+		break;
+	case PHY_INTERFACE_MODE_SGMII:
+		if (MTK_HAS_CAPS(eth->soc->caps, MTK_SGMII))
+			mtk_gmac_sgmii_hw_setup(eth, mac->id);
+		break;
 
+	case PHY_INTERFACE_MODE_INTERNAL:
+		if (MTK_HAS_CAPS(eth->soc->caps, MTK_GMAC1_ESW) && !mac->id)
+			/* Setup the path through ESW internal switch */
+			mtk_w32(eth, MTK_MUX_TO_ESW, MTK_MAC_MISC);

This bit is interesting. Generally, there is no PHY at all between the MAC and the switch. So i don't think this is correct. Please can you take this out for the moment, until you actually add support for the switch. We can discuss it then, when we see the bigger picture.

Andrew

author
#5 lore raw

Re: [PATCH net-next 2/4] net-next: mediatek: add platform data to adapt into various hardware

In reply to Andrew Lunn
Quoted 31 lines · Andrew Lunn
Quoted 31 lines
drivers/net/ethernet/mediatek/mtk_eth_soc.c +23 -0
+static int mtk_clk_enable(struct mtk_eth *eth)
+{
+	int clk, ret;
+
+	for (clk = 0; clk < MTK_CLK_MAX ; clk++) {
+		if (eth->clks[clk]) {
+			ret = clk_prepare_enable(eth->clks[clk]);
+			if (ret)
+				goto err_disable_clks;
+		}
+	}
+
+	return 0;
+
+err_disable_clks:
+	while (--clk >= 0) {
+		if (eth->clks[clk])
+			clk_disable_unprepare(eth->clks[clk]);
+	}
+
+	return ret;
+}
 
+
 static int mtk_hw_init(struct mtk_eth *eth)
 {
 	int i, val;
@@ -1847,10 +1881,8 @@ static int mtk_hw_init(struct mtk_eth *eth)
 	pm_runtime_enable(eth->dev);
 	pm_runtime_get_sync(eth->dev);
 
Quoted 9 lines

drivers/net/ethernet/mediatek/mtk_eth_soc.c static int mtk_hw_init(struct mtk_eth *eth) · line 1885

Quoted 6 lines
drivers/net/ethernet/mediatek/mtk_eth_soc.c +2 -4
-	clk_prepare_enable(eth->clks[MTK_CLK_ETHIF]);
-	clk_prepare_enable(eth->clks[MTK_CLK_ESW]);
-	clk_prepare_enable(eth->clks[MTK_CLK_GP1]);
-	clk_prepare_enable(eth->clks[MTK_CLK_GP2]);
+	mtk_clk_enable(eth);
+

mtk_clk_enable() returns an error code. It is probably a good idea to use it, especially if it could be EPRODE_DEFER.

okay, I will improve those clocks handling better along with Florian's suggestion in the next version

Sean

Quoted 2 lines

Andrew