Skip to contentSkip to conversation

Add MMC software queue support

PATCH Superseded Baolin Wang 3 participants 9 messages Sep 19, 2019 – Sep 27, 2019

Subsystems (3)

v3 of 6 Superseded Latest is v6 →

lore
Share & tools
lore
#0 lore raw

v3 cover Add MMC software queue support

Hi All,

Now the MMC read/write stack will always wait for previous request is completed by mmc_blk_rw_wait(), before sending a new request to hardware, or queue a work to complete request, that will bring context switching overhead, especially for high I/O per second rates, to affect the IO performance.

Thus this patch set will introduce the MMC software command queue support based on command queue engine's interfaces, and set the queue depth as 2, that means we do not need wait for previous request is completed and can queue 2 requests in flight. It is enough to let the irq handler always trigger the next request without a context switch and then ask the blk_mq layer for the next one to get queued, as well as avoiding a long latency.

Moreover we can expand the MMC software queue interface to support MMC packed request or packed command instead of adding new interfaces, according to previosus discussion.

Below are some comparison data with fio tool. The fio command I used is like below with changing the '--rw' parameter and enabling the direct IO flag to measure the actual hardware transfer speed in 4K block size.

./fio --filename=/dev/mmcblk0p30 --direct=1 --iodepth=20 --rw=read --bs=4K --size=512M --group_reporting --numjobs=20 --name=test_read

My eMMC card working at HS400 Enhanced strobe mode:

[    2.229856] mmc0: new HS400 Enhanced strobe MMC card at address 0001
[    2.237566] mmcblk0: mmc0:0001 HBG4a2 29.1 GiB 
[    2.242621] mmcblk0boot0: mmc0:0001 HBG4a2 partition 1 4.00 MiB
[    2.249110] mmcblk0boot1: mmc0:0001 HBG4a2 partition 2 4.00 MiB
[    2.255307] mmcblk0rpmb: mmc0:0001 HBG4a2 partition 3 4.00 MiB, chardev (248:0)

1. Without MMC software queue
I tested 3 times for each case and output a average speed.

1) Sequential read:
Speed: 28.9MiB/s, 26.4MiB/s, 30.9MiB/s
Average speed: 28.7MiB/s

2) Random read:
Speed: 18.2MiB/s, 8.9MiB/s, 15.8MiB/s
Average speed: 14.3MiB/s

3) Sequential write:
Speed: 21.1MiB/s, 27.9MiB/s, 25MiB/s
Average speed: 24.7MiB/s

4) Random write:
Speed: 21.5MiB/s, 18.1MiB/s, 18.1MiB/s
Average speed: 19.2MiB/s

2. With MMC software queue
I tested 3 times for each case and output a average speed.

1) Sequential read:
Speed: 44.1MiB/s, 42.3MiB/s, 44.4MiB/s
Average speed: 43.6MiB/s

2) Random read:
Speed: 30.6MiB/s, 30.9MiB/s, 30.5MiB/s
Average speed: 30.6MiB/s

3) Sequential write:
Speed: 44.1MiB/s, 45.9MiB/s, 44.2MiB/s
Average speed: 44.7MiB/s

4) Random write:
Speed: 45.1MiB/s, 43.3MiB/s, 42.4MiB/s
Average speed: 43.6MiB/s

Form above data, we can see the MMC software queue can help to improve the performance obviously.

Any comments are welcome. Thanks a lot.

Changes from v2:
- Remove reference to 'struct cqhci_host' and 'struct cqhci_slot', instead adding 'struct sqhci_host', which is only used by software queue.

Changes from v1:
- Add request_done ops for sdhci_ops.
- Replace virtual command queue with software queue for functions and variables.
- Rename the software queue file and add sqhci.h header file.

Baolin Wang (3):
mmc: Add MMC software queue support
mmc: host: sdhci: Add request_done ops for struct sdhci_ops
mmc: host: sdhci-sprd: Add software queue support

 drivers/mmc/core/block.c      |   61 ++++++++
 drivers/mmc/core/mmc.c        |   13 +-
 drivers/mmc/core/queue.c      |   25 ++-
 drivers/mmc/host/Kconfig      |    9 ++
 drivers/mmc/host/Makefile     |    1 +
 drivers/mmc/host/sdhci-sprd.c |   26 ++++
 drivers/mmc/host/sdhci.c      |   12 +-
 drivers/mmc/host/sdhci.h      |    2 +
 drivers/mmc/host/sqhci.c      |  344 +++++++++++++++++++++++++++++++++++++++++
 drivers/mmc/host/sqhci.h      |   53 +++++++
 include/linux/mmc/host.h      |    3 +
 11 files changed, 537 insertions(+), 12 deletions(-)
 create mode 100644 drivers/mmc/host/sqhci.c
 create mode 100644 drivers/mmc/host/sqhci.h
Signature · 1 line
1.7.9.5
#1 lore raw

PATCH v3 1/3 mmc: Add MMC software queue support

Now the MMC read/write stack will always wait for previous request is completed by mmc_blk_rw_wait(), before sending a new request to hardware, or queue a work to complete request, that will bring context switching overhead, especially for high I/O per second rates, to affect the IO performance.

Thus this patch introduces MMC software queue interface based on the hardware command queue engine's interfaces, which is similar with the hardware command queue engine's idea, that can remove the context switching. Moreover we set the queue depth as 2 for software queue, that is enough to let the irq handler always trigger the next request without a context switch and then ask the blk_mq layer for the next one to get queued, as well as avoiding a long latency.

Quoted 1 line

From the fio testing data in cover letter, we can see the software

queue can improve performance obviously with 4K block size, increasing about 52% for sequential read, increasing about 114% for random read, increasing about 81% for sequential write, and increasing about 127% for random write.

Moreover we can expand the software queue interface to support MMC packed request or packed command in future.

---
 drivers/mmc/core/block.c  |   61 ++++++++
 drivers/mmc/core/mmc.c    |   13 +-
 drivers/mmc/core/queue.c  |   25 +++-
 drivers/mmc/host/Kconfig  |    8 ++
 drivers/mmc/host/Makefile |    1 +
 drivers/mmc/host/sqhci.c  |  344 +++++++++++++++++++++++++++++++++++++++++++++
 drivers/mmc/host/sqhci.h  |   53 +++++++
 include/linux/mmc/host.h  |    3 +
 8 files changed, 498 insertions(+), 10 deletions(-)
 create mode 100644 drivers/mmc/host/sqhci.c
 create mode 100644 drivers/mmc/host/sqhci.h
drivers/mmc/core/block.c +61 -0
index 2c71a43..870462c 100644
@@ -168,6 +168,11 @@ struct mmc_rpmb_data {
 
 static inline int mmc_blk_part_switch(struct mmc_card *card,
 				      unsigned int part_type);
+static void mmc_blk_rw_rq_prep(struct mmc_queue_req *mqrq,
+			       struct mmc_card *card,
+			       int disable_multi,
+			       struct mmc_queue *mq);
+static void mmc_blk_swq_req_done(struct mmc_request *mrq);
 
 static struct mmc_blk_data *mmc_blk_get(struct gendisk *disk)
 {
@@ -1569,9 +1574,30 @@ static int mmc_blk_cqe_issue_flush(struct mmc_queue *mq, struct request *req)
 	return mmc_blk_cqe_start_req(mq->card->host, mrq);
 }
 
+static int mmc_blk_swq_issue_rw_rq(struct mmc_queue *mq, struct request *req)
+{
+	struct mmc_queue_req *mqrq = req_to_mmc_queue_req(req);
+	struct mmc_host *host = mq->card->host;
+	int err;
+
+	mmc_blk_rw_rq_prep(mqrq, mq->card, 0, mq);
+	mqrq->brq.mrq.done = mmc_blk_swq_req_done;
+	mmc_pre_req(host, &mqrq->brq.mrq);
+
+	err = mmc_cqe_start_req(host, &mqrq->brq.mrq);
+	if (err)
+		mmc_post_req(host, &mqrq->brq.mrq, err);
+
+	return err;
+}
+
 static int mmc_blk_cqe_issue_rw_rq(struct mmc_queue *mq, struct request *req)
 {
 	struct mmc_queue_req *mqrq = req_to_mmc_queue_req(req);
+	struct mmc_host *host = mq->card->host;
+
+	if (host->swq_enabled)
+		return mmc_blk_swq_issue_rw_rq(mq, req);
 
 	mmc_blk_data_prep(mq, mqrq, 0, NULL, NULL);
 
@@ -1957,6 +1983,41 @@ static void mmc_blk_urgent_bkops(struct mmc_queue *mq,
 		mmc_run_bkops(mq->card);
 }
 
+static void mmc_blk_swq_req_done(struct mmc_request *mrq)
+{
+	struct mmc_queue_req *mqrq =
+		container_of(mrq, struct mmc_queue_req, brq.mrq);
+	struct request *req = mmc_queue_req_to_req(mqrq);
+	struct request_queue *q = req->q;
+	struct mmc_queue *mq = q->queuedata;
+	struct mmc_host *host = mq->card->host;
+	unsigned long flags;
+
+	if (mmc_blk_rq_error(&mqrq->brq) ||
+	    mmc_blk_urgent_bkops_needed(mq, mqrq)) {
+		spin_lock_irqsave(&mq->lock, flags);
+		mq->recovery_needed = true;
+		mq->recovery_req = req;
+		spin_unlock_irqrestore(&mq->lock, flags);
+
+		host->cqe_ops->cqe_recovery_start(host);
+
+		schedule_work(&mq->recovery_work);
+		return;
+	}
+
+	mmc_blk_rw_reset_success(mq, req);
+
+	/*
+	 * Block layer timeouts race with completions which means the normal
+	 * completion path cannot be used during recovery.
+	 */
+	if (mq->in_recovery)
+		mmc_blk_cqe_complete_rq(mq, req);
+	else
+		blk_mq_complete_request(req);
+}
+
 void mmc_blk_mq_complete(struct request *req)
 {
 	struct mmc_queue *mq = req->q->queuedata;
drivers/mmc/core/mmc.c +10 -3
index c880489..8eac1a2 100644
@@ -1852,15 +1852,22 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
 	 */
 	card->reenable_cmdq = card->ext_csd.cmdq_en;
 
-	if (card->ext_csd.cmdq_en && !host->cqe_enabled) {
+	if (host->cqe_ops && !host->cqe_enabled) {
 		err = host->cqe_ops->cqe_enable(host, card);
 		if (err) {
 			pr_err("%s: Failed to enable CQE, error %d\n",
 				mmc_hostname(host), err);
 		} else {
 			host->cqe_enabled = true;
-			pr_info("%s: Command Queue Engine enabled\n",
-				mmc_hostname(host));
+
+			if (card->ext_csd.cmdq_en) {
+				pr_info("%s: Command Queue Engine enabled\n",
+					mmc_hostname(host));
+			} else {
+				host->swq_enabled = true;
+				pr_info("%s: Software Queue enabled\n",
+					mmc_hostname(host));
+			}
 		}
 	}
 
drivers/mmc/core/queue.c +18 -7
index 7102e2e..2c93c29 100644
@@ -60,7 +60,7 @@ enum mmc_issue_type mmc_issue_type(struct mmc_queue *mq, struct request *req)
 {
 	struct mmc_host *host = mq->card->host;
 
-	if (mq->use_cqe)
+	if (mq->use_cqe && !host->swq_enabled)
 		return mmc_cqe_issue_type(host, req);
 
 	if (req_op(req) == REQ_OP_READ || req_op(req) == REQ_OP_WRITE)
@@ -122,12 +122,14 @@ static enum blk_eh_timer_return mmc_mq_timed_out(struct request *req,
 {
 	struct request_queue *q = req->q;
 	struct mmc_queue *mq = q->queuedata;
+	struct mmc_card *card = mq->card;
+	struct mmc_host *host = card->host;
 	unsigned long flags;
 	int ret;
 
 	spin_lock_irqsave(&mq->lock, flags);
 
-	if (mq->recovery_needed || !mq->use_cqe)
+	if (mq->recovery_needed || !mq->use_cqe || host->swq_enabled)
 		ret = BLK_EH_RESET_TIMER;
 	else
 		ret = mmc_cqe_timed_out(req);
@@ -142,12 +144,13 @@ static void mmc_mq_recovery_handler(struct work_struct *work)
 	struct mmc_queue *mq = container_of(work, struct mmc_queue,
 					    recovery_work);
 	struct request_queue *q = mq->queue;
+	struct mmc_host *host = mq->card->host;
 
 	mmc_get_card(mq->card, &mq->ctx);
 
 	mq->in_recovery = true;
 
-	if (mq->use_cqe)
+	if (mq->use_cqe && !host->swq_enabled)
 		mmc_blk_cqe_recovery(mq);
 	else
 		mmc_blk_mq_recovery(mq);
@@ -158,6 +161,9 @@ static void mmc_mq_recovery_handler(struct work_struct *work)
 	mq->recovery_needed = false;
 	spin_unlock_irq(&mq->lock);
 
+	if (host->swq_enabled)
+		host->cqe_ops->cqe_recovery_finish(host);
+
 	mmc_put_card(mq->card, &mq->ctx);
 
 	blk_mq_run_hw_queues(q, true);
@@ -407,11 +413,16 @@ int mmc_init_queue(struct mmc_queue *mq, struct mmc_card *card)
 	 * The queue depth for CQE must match the hardware because the request
 	 * tag is used to index the hardware queue.
 	 */
-	if (mq->use_cqe)
-		mq->tag_set.queue_depth =
-			min_t(int, card->ext_csd.cmdq_depth, host->cqe_qdepth);
-	else
+	if (mq->use_cqe) {
+		if (host->swq_enabled)
+			mq->tag_set.queue_depth = host->cqe_qdepth;
+		else
+			mq->tag_set.queue_depth =
+				min_t(int, card->ext_csd.cmdq_depth, host->cqe_qdepth);
+	} else {
 		mq->tag_set.queue_depth = MMC_QUEUE_DEPTH;
+	}
+
 	mq->tag_set.numa_node = NUMA_NO_NODE;
 	mq->tag_set.flags = BLK_MQ_F_SHOULD_MERGE | BLK_MQ_F_BLOCKING;
 	mq->tag_set.nr_hw_queues = 1;
drivers/mmc/host/Kconfig +8 -0
index 14d89a1..d117f18 100644
@@ -923,6 +923,14 @@ config MMC_CQHCI
 
 	  If unsure, say N.
 
+config MMC_SQHCI
+	bool "Software Queue Host Controller Interface support"
+	help
+	  This selects the Software Queue Host Controller Interface (SQHCI)
+	  support.
+
+	  If unsure, say N.
+
 config MMC_TOSHIBA_PCI
 	tristate "Toshiba Type A SD/MMC Card Interface Driver"
 	depends on PCI
drivers/mmc/host/Makefile +1 -0
index 7357871..a3588d4 100644
@@ -97,6 +97,7 @@ obj-$(CONFIG_MMC_SDHCI_BRCMSTB)		+= sdhci-brcmstb.o
 obj-$(CONFIG_MMC_SDHCI_OMAP)		+= sdhci-omap.o
 obj-$(CONFIG_MMC_SDHCI_SPRD)		+= sdhci-sprd.o
 obj-$(CONFIG_MMC_CQHCI)			+= cqhci.o
+obj-$(CONFIG_MMC_SQHCI)			+= sqhci.o
 
 ifeq ($(CONFIG_CB710_DEBUG),y)
 	CFLAGS-cb710-mmc	+= -DDEBUG
drivers/mmc/host/sqhci.c new file +344 -0

344 lines not on this page · raw message

drivers/mmc/host/sqhci.h new file +53 -0

53 lines not on this page · raw message

include/linux/mmc/host.h +3 -0
index 4a351cb..706e2bc 100644
@@ -459,6 +459,9 @@ struct mmc_host {
 	bool			cqe_enabled;
 	bool			cqe_on;
 
+	/* Software Queue support */
+	bool			swq_enabled;
+
 	unsigned long		private[0] ____cacheline_aligned;
 };
 
Signature · 1 line
1.7.9.5
#4 lore raw

PATCH v3 2/3 mmc: host: sdhci: Add request_done ops for struct sdhci_ops

In reply to Baolin Wang

Add request_done ops for struct sdhci_ops as a preparation in case some host controllers have different method to complete one request, such as supporting request completion of MMC software queue.

---
 drivers/mmc/host/sdhci.c |   12 ++++++++++--
 drivers/mmc/host/sdhci.h |    2 ++
 2 files changed, 12 insertions(+), 2 deletions(-)
drivers/mmc/host/sdhci.c +10 -2
index a5dc5aa..b2c8695 100644
@@ -2710,7 +2710,10 @@ static bool sdhci_request_done(struct sdhci_host *host)
 
 	spin_unlock_irqrestore(&host->lock, flags);
 
-	mmc_request_done(host->mmc, mrq);
+	if (host->ops->request_done)
+		host->ops->request_done(host, mrq);
+	else
+		mmc_request_done(host->mmc, mrq);
 
 	return false;
 }
@@ -3133,7 +3136,12 @@ static irqreturn_t sdhci_irq(int irq, void *dev_id)
 
 	/* Process mrqs ready for immediate completion */
 	for (i = 0; i < SDHCI_MAX_MRQS; i++) {
-		if (mrqs_done[i])
+		if (!mrqs_done[i])
+			continue;
+
+		if (host->ops->request_done)
+			host->ops->request_done(host, mrqs_done[i]);
+		else
 			mmc_request_done(host->mmc, mrqs_done[i]);
 	}
 
drivers/mmc/host/sdhci.h +2 -0
index 902f855..e9a476f 100644
@@ -643,6 +643,8 @@ struct sdhci_ops {
 	void	(*voltage_switch)(struct sdhci_host *host);
 	void	(*adma_write_desc)(struct sdhci_host *host, void **desc,
 				   dma_addr_t addr, int len, unsigned int cmd);
+	void	(*request_done)(struct sdhci_host *host,
+				struct mmc_request *mrq);
 };
 
 #ifdef CONFIG_MMC_SDHCI_IO_ACCESSORS
Signature · 1 line
1.7.9.5
#5 lore raw

PATCH v3 3/3 mmc: host: sdhci-sprd: Add software queue support

In reply to Baolin Wang

Add software queue support to improve the performance.

---
 drivers/mmc/host/Kconfig      |    1 +
 drivers/mmc/host/sdhci-sprd.c |   26 ++++++++++++++++++++++++++
 2 files changed, 27 insertions(+)
drivers/mmc/host/Kconfig +1 -0
index d117f18..862e8e9 100644
@@ -619,6 +619,7 @@ config MMC_SDHCI_SPRD
 	depends on ARCH_SPRD
 	depends on MMC_SDHCI_PLTFM
 	select MMC_SDHCI_IO_ACCESSORS
+	select MMC_SQHCI
 	help
 	  This selects the SDIO Host Controller in Spreadtrum
 	  SoCs, this driver supports R11(IP version: R11P0).
drivers/mmc/host/sdhci-sprd.c +26 -0
index d07b979..4dec0b3 100644
@@ -19,6 +19,7 @@
 #include <linux/slab.h>
 
 #include "sdhci-pltfm.h"
+#include "sqhci.h"
 
 /* SDHCI_ARGUMENT2 register high 16bit */
 #define SDHCI_SPRD_ARG2_STUFF		GENMASK(31, 16)
@@ -379,6 +380,16 @@ static unsigned int sdhci_sprd_get_ro(struct sdhci_host *host)
 	return 0;
 }
 
+static void sdhci_sprd_request_done(struct sdhci_host *host,
+				    struct mmc_request *mrq)
+{
+	/* Validate if the request was from software queue firstly. */
+	if (sqhci_finalize_request(host->mmc, mrq))
+		return;
+
+	 mmc_request_done(host->mmc, mrq);
+}
+
 static struct sdhci_ops sdhci_sprd_ops = {
 	.read_l = sdhci_sprd_readl,
 	.write_l = sdhci_sprd_writel,
@@ -392,6 +403,7 @@ static unsigned int sdhci_sprd_get_ro(struct sdhci_host *host)
 	.hw_reset = sdhci_sprd_hw_reset,
 	.get_max_timeout_count = sdhci_sprd_get_max_timeout_count,
 	.get_ro = sdhci_sprd_get_ro,
+	.request_done = sdhci_sprd_request_done,
 };
 
 static void sdhci_sprd_request(struct mmc_host *mmc, struct mmc_request *mrq)
@@ -521,6 +533,7 @@ static int sdhci_sprd_probe(struct platform_device *pdev)
 {
 	struct sdhci_host *host;
 	struct sdhci_sprd_host *sprd_host;
+	struct sqhci_host *sq_host;
 	struct clk *clk;
 	int ret = 0;
 
@@ -631,6 +644,16 @@ static int sdhci_sprd_probe(struct platform_device *pdev)
 
 	sprd_host->flags = host->flags;
 
+	sq_host = devm_kzalloc(&pdev->dev, sizeof(*sq_host), GFP_KERNEL);
+	if (!sq_host) {
+		ret = -ENOMEM;
+		goto err_cleanup_host;
+	}
+
+	ret = sqhci_init(sq_host, host->mmc);
+	if (ret)
+		goto err_cleanup_host;
+
 	ret = __sdhci_add_host(host);
 	if (ret)
 		goto err_cleanup_host;
@@ -689,6 +712,7 @@ static int sdhci_sprd_runtime_suspend(struct device *dev)
 	struct sdhci_host *host = dev_get_drvdata(dev);
 	struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host);
 
+	sqhci_suspend(host->mmc);
 	sdhci_runtime_suspend_host(host);
 
 	clk_disable_unprepare(sprd_host->clk_sdio);
@@ -717,6 +741,8 @@ static int sdhci_sprd_runtime_resume(struct device *dev)
 		goto clk_disable;
 
 	sdhci_runtime_resume_host(host, 1);
+	sqhci_resume(host->mmc);
+
 	return 0;
 
 clk_disable:
Signature · 1 line
1.7.9.5
#2 lore raw

Re: [PATCH v3 1/3] mmc: Add MMC software queue support

In reply to Baolin Wang
I love your patch! Yet something to improve:

Hi Baolin,

I love your patch! Yet something to improve:

[auto build test ERROR on linus/master]
[cannot apply to v5.3 next-20190918]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system. BTW, we also suggest to use '--base' option to specify the base tree in git format-patch, please see https://stackoverflow.com/a/37406982]

url: https://github.com/0day-ci/linux/commits/Baolin-Wang/mmc-Add-MMC-software-queue-support/20190919-140107
config: i386-allmodconfig (attached as .config)
compiler: gcc-7 (Debian 7.4.0-13) 7.4.0
reproduce:

        # save the attached .config to linux build tree
        make ARCH=i386 
:::::: branch date: 7 hours ago
:::::: commit date: 7 hours ago

If you fix the issue, kindly add following tag

All errors (new ones prefixed by >>):

ld: drivers/mmc/host/sqhci.o: in function `sqhci_finalize_request':

>> (.text+0x644): undefined reference to `mmc_cqe_request_done'

---
0-DAY kernel test infrastructure Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all Intel Corporation

#3 lore raw

Re: [PATCH v3 1/3] mmc: Add MMC software queue support

Hi,

Quoted 20 lines · kbuild test robot

Hi Baolin,

I love your patch! Yet something to improve:

[auto build test ERROR on linus/master]
[cannot apply to v5.3 next-20190918]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system. BTW, we also suggest to use '--base' option to specify the base tree in git format-patch, please see https://stackoverflow.com/a/37406982]

url: https://github.com/0day-ci/linux/commits/Baolin-Wang/mmc-Add-MMC-software-queue-support/20190919-140107
config: i386-allmodconfig (attached as .config)
compiler: gcc-7 (Debian 7.4.0-13) 7.4.0
reproduce:

        # save the attached .config to linux build tree
        make ARCH=i386
:::::: branch date: 7 hours ago
:::::: commit date: 7 hours ago
Quoted 7 lines

If you fix the issue, kindly add following tag

All errors (new ones prefixed by >>):

ld: drivers/mmc/host/sqhci.o: in function `sqhci_finalize_request':

Quoted 1 line
Quoted 1 line

(.text+0x644): undefined reference to `mmc_cqe_request_done'

OK. I will fix this issue in the next version and wait for a while to see if there are any new comments for this patch set. Thanks.

Signature · 2 lines
Baolin Wang
Best Regards
#6 lore raw
In reply to Baolin Wang

Hi Adrian and Ulf,

Quoted 80 lines · Baolin Wang

Hi All,

Now the MMC read/write stack will always wait for previous request is completed by mmc_blk_rw_wait(), before sending a new request to hardware, or queue a work to complete request, that will bring context switching overhead, especially for high I/O per second rates, to affect the IO performance.

Thus this patch set will introduce the MMC software command queue support based on command queue engine's interfaces, and set the queue depth as 2, that means we do not need wait for previous request is completed and can queue 2 requests in flight. It is enough to let the irq handler always trigger the next request without a context switch and then ask the blk_mq layer for the next one to get queued, as well as avoiding a long latency.

Moreover we can expand the MMC software queue interface to support MMC packed request or packed command instead of adding new interfaces, according to previosus discussion.

Below are some comparison data with fio tool. The fio command I used is like below with changing the '--rw' parameter and enabling the direct IO flag to measure the actual hardware transfer speed in 4K block size.

./fio --filename=/dev/mmcblk0p30 --direct=1 --iodepth=20 --rw=read --bs=4K --size=512M --group_reporting --numjobs=20 --name=test_read

My eMMC card working at HS400 Enhanced strobe mode:

[    2.229856] mmc0: new HS400 Enhanced strobe MMC card at address 0001
[    2.237566] mmcblk0: mmc0:0001 HBG4a2 29.1 GiB
[    2.242621] mmcblk0boot0: mmc0:0001 HBG4a2 partition 1 4.00 MiB
[    2.249110] mmcblk0boot1: mmc0:0001 HBG4a2 partition 2 4.00 MiB
[    2.255307] mmcblk0rpmb: mmc0:0001 HBG4a2 partition 3 4.00 MiB, chardev (248:0)

1. Without MMC software queue
I tested 3 times for each case and output a average speed.

1) Sequential read:
Speed: 28.9MiB/s, 26.4MiB/s, 30.9MiB/s
Average speed: 28.7MiB/s

2) Random read:
Speed: 18.2MiB/s, 8.9MiB/s, 15.8MiB/s
Average speed: 14.3MiB/s

3) Sequential write:
Speed: 21.1MiB/s, 27.9MiB/s, 25MiB/s
Average speed: 24.7MiB/s

4) Random write:
Speed: 21.5MiB/s, 18.1MiB/s, 18.1MiB/s
Average speed: 19.2MiB/s

2. With MMC software queue
I tested 3 times for each case and output a average speed.

1) Sequential read:
Speed: 44.1MiB/s, 42.3MiB/s, 44.4MiB/s
Average speed: 43.6MiB/s

2) Random read:
Speed: 30.6MiB/s, 30.9MiB/s, 30.5MiB/s
Average speed: 30.6MiB/s

3) Sequential write:
Speed: 44.1MiB/s, 45.9MiB/s, 44.2MiB/s
Average speed: 44.7MiB/s

4) Random write:
Speed: 45.1MiB/s, 43.3MiB/s, 42.4MiB/s
Average speed: 43.6MiB/s

Form above data, we can see the MMC software queue can help to improve the performance obviously.

Any comments are welcome. Thanks a lot.

Changes from v2:
- Remove reference to 'struct cqhci_host' and 'struct cqhci_slot', instead adding 'struct sqhci_host', which is only used by software queue.

Quoted 5 lines

Changes from v1:
- Add request_done ops for sdhci_ops.
- Replace virtual command queue with software queue for functions and variables.
- Rename the software queue file and add sqhci.h header file.

Do you have any comments for this patch set except the random config building issue that will be fixed in the next version? Thanks.

Quoted 24 lines

Baolin Wang (3):
mmc: Add MMC software queue support
mmc: host: sdhci: Add request_done ops for struct sdhci_ops
mmc: host: sdhci-sprd: Add software queue support

 drivers/mmc/core/block.c      |   61 ++++++++
 drivers/mmc/core/mmc.c        |   13 +-
 drivers/mmc/core/queue.c      |   25 ++-
 drivers/mmc/host/Kconfig      |    9 ++
 drivers/mmc/host/Makefile     |    1 +
 drivers/mmc/host/sdhci-sprd.c |   26 ++++
 drivers/mmc/host/sdhci.c      |   12 +-
 drivers/mmc/host/sdhci.h      |    2 +
 drivers/mmc/host/sqhci.c      |  344 +++++++++++++++++++++++++++++++++++++++++
 drivers/mmc/host/sqhci.h      |   53 +++++++
 include/linux/mmc/host.h      |    3 +
 11 files changed, 537 insertions(+), 12 deletions(-)
 create mode 100644 drivers/mmc/host/sqhci.c
 create mode 100644 drivers/mmc/host/sqhci.h

--
1.7.9.5

Signature · 2 lines
Baolin Wang
Best Regards
maintainer
#7 lore raw
Quoted 83 lines · Baolin Wang

Hi Adrian and Ulf,

Quoted 80 lines · Baolin Wang

Hi All,

Now the MMC read/write stack will always wait for previous request is completed by mmc_blk_rw_wait(), before sending a new request to hardware, or queue a work to complete request, that will bring context switching overhead, especially for high I/O per second rates, to affect the IO performance.

Thus this patch set will introduce the MMC software command queue support based on command queue engine's interfaces, and set the queue depth as 2, that means we do not need wait for previous request is completed and can queue 2 requests in flight. It is enough to let the irq handler always trigger the next request without a context switch and then ask the blk_mq layer for the next one to get queued, as well as avoiding a long latency.

Moreover we can expand the MMC software queue interface to support MMC packed request or packed command instead of adding new interfaces, according to previosus discussion.

Below are some comparison data with fio tool. The fio command I used is like below with changing the '--rw' parameter and enabling the direct IO flag to measure the actual hardware transfer speed in 4K block size.

./fio --filename=/dev/mmcblk0p30 --direct=1 --iodepth=20 --rw=read --bs=4K --size=512M --group_reporting --numjobs=20 --name=test_read

My eMMC card working at HS400 Enhanced strobe mode:

[    2.229856] mmc0: new HS400 Enhanced strobe MMC card at address 0001
[    2.237566] mmcblk0: mmc0:0001 HBG4a2 29.1 GiB
[    2.242621] mmcblk0boot0: mmc0:0001 HBG4a2 partition 1 4.00 MiB
[    2.249110] mmcblk0boot1: mmc0:0001 HBG4a2 partition 2 4.00 MiB
[    2.255307] mmcblk0rpmb: mmc0:0001 HBG4a2 partition 3 4.00 MiB, chardev (248:0)

1. Without MMC software queue
I tested 3 times for each case and output a average speed.

1) Sequential read:
Speed: 28.9MiB/s, 26.4MiB/s, 30.9MiB/s
Average speed: 28.7MiB/s

2) Random read:
Speed: 18.2MiB/s, 8.9MiB/s, 15.8MiB/s
Average speed: 14.3MiB/s

3) Sequential write:
Speed: 21.1MiB/s, 27.9MiB/s, 25MiB/s
Average speed: 24.7MiB/s

4) Random write:
Speed: 21.5MiB/s, 18.1MiB/s, 18.1MiB/s
Average speed: 19.2MiB/s

2. With MMC software queue
I tested 3 times for each case and output a average speed.

1) Sequential read:
Speed: 44.1MiB/s, 42.3MiB/s, 44.4MiB/s
Average speed: 43.6MiB/s

2) Random read:
Speed: 30.6MiB/s, 30.9MiB/s, 30.5MiB/s
Average speed: 30.6MiB/s

3) Sequential write:
Speed: 44.1MiB/s, 45.9MiB/s, 44.2MiB/s
Average speed: 44.7MiB/s

4) Random write:
Speed: 45.1MiB/s, 43.3MiB/s, 42.4MiB/s
Average speed: 43.6MiB/s

Form above data, we can see the MMC software queue can help to improve the performance obviously.

Any comments are welcome. Thanks a lot.

Changes from v2:
- Remove reference to 'struct cqhci_host' and 'struct cqhci_slot', instead adding 'struct sqhci_host', which is only used by software queue.

Quoted 8 lines
Quoted 5 lines

Changes from v1:
- Add request_done ops for sdhci_ops.
- Replace virtual command queue with software queue for functions and variables.
- Rename the software queue file and add sqhci.h header file.

Do you have any comments for this patch set except the random config building issue that will be fixed in the next version? Thanks.

Pedantically, swhci is not a host controller interface, so the name still seems inappropriate. Otherwise I haven't had time to look at it, sorry.

Quoted 27 lines
Quoted 25 lines

Baolin Wang (3):
mmc: Add MMC software queue support
mmc: host: sdhci: Add request_done ops for struct sdhci_ops
mmc: host: sdhci-sprd: Add software queue support

 drivers/mmc/core/block.c      |   61 ++++++++
 drivers/mmc/core/mmc.c        |   13 +-
 drivers/mmc/core/queue.c      |   25 ++-
 drivers/mmc/host/Kconfig      |    9 ++
 drivers/mmc/host/Makefile     |    1 +
 drivers/mmc/host/sdhci-sprd.c |   26 ++++
 drivers/mmc/host/sdhci.c      |   12 +-
 drivers/mmc/host/sdhci.h      |    2 +
 drivers/mmc/host/sqhci.c      |  344 +++++++++++++++++++++++++++++++++++++++++
 drivers/mmc/host/sqhci.h      |   53 +++++++
 include/linux/mmc/host.h      |    3 +
 11 files changed, 537 insertions(+), 12 deletions(-)
 create mode 100644 drivers/mmc/host/sqhci.c
 create mode 100644 drivers/mmc/host/sqhci.h

--
1.7.9.5

#8 lore raw
Quoted 91 lines · Adrian Hunter
Quoted 89 lines · Baolin Wang

Hi Adrian and Ulf,

Quoted 85 lines · Baolin Wang

Hi All,

Now the MMC read/write stack will always wait for previous request is completed by mmc_blk_rw_wait(), before sending a new request to hardware, or queue a work to complete request, that will bring context switching overhead, especially for high I/O per second rates, to affect the IO performance.

Thus this patch set will introduce the MMC software command queue support based on command queue engine's interfaces, and set the queue depth as 2, that means we do not need wait for previous request is completed and can queue 2 requests in flight. It is enough to let the irq handler always trigger the next request without a context switch and then ask the blk_mq layer for the next one to get queued, as well as avoiding a long latency.

Moreover we can expand the MMC software queue interface to support MMC packed request or packed command instead of adding new interfaces, according to previosus discussion.

Below are some comparison data with fio tool. The fio command I used is like below with changing the '--rw' parameter and enabling the direct IO flag to measure the actual hardware transfer speed in 4K block size.

./fio --filename=/dev/mmcblk0p30 --direct=1 --iodepth=20 --rw=read --bs=4K --size=512M --group_reporting --numjobs=20 --name=test_read

My eMMC card working at HS400 Enhanced strobe mode:

[    2.229856] mmc0: new HS400 Enhanced strobe MMC card at address 0001
[    2.237566] mmcblk0: mmc0:0001 HBG4a2 29.1 GiB
[    2.242621] mmcblk0boot0: mmc0:0001 HBG4a2 partition 1 4.00 MiB
[    2.249110] mmcblk0boot1: mmc0:0001 HBG4a2 partition 2 4.00 MiB
[    2.255307] mmcblk0rpmb: mmc0:0001 HBG4a2 partition 3 4.00 MiB, chardev (248:0)

1. Without MMC software queue
I tested 3 times for each case and output a average speed.

1) Sequential read:
Speed: 28.9MiB/s, 26.4MiB/s, 30.9MiB/s
Average speed: 28.7MiB/s

2) Random read:
Speed: 18.2MiB/s, 8.9MiB/s, 15.8MiB/s
Average speed: 14.3MiB/s

3) Sequential write:
Speed: 21.1MiB/s, 27.9MiB/s, 25MiB/s
Average speed: 24.7MiB/s

4) Random write:
Speed: 21.5MiB/s, 18.1MiB/s, 18.1MiB/s
Average speed: 19.2MiB/s

2. With MMC software queue
I tested 3 times for each case and output a average speed.

1) Sequential read:
Speed: 44.1MiB/s, 42.3MiB/s, 44.4MiB/s
Average speed: 43.6MiB/s

2) Random read:
Speed: 30.6MiB/s, 30.9MiB/s, 30.5MiB/s
Average speed: 30.6MiB/s

3) Sequential write:
Speed: 44.1MiB/s, 45.9MiB/s, 44.2MiB/s
Average speed: 44.7MiB/s

4) Random write:
Speed: 45.1MiB/s, 43.3MiB/s, 42.4MiB/s
Average speed: 43.6MiB/s

Form above data, we can see the MMC software queue can help to improve the performance obviously.

Any comments are welcome. Thanks a lot.

Changes from v2:
- Remove reference to 'struct cqhci_host' and 'struct cqhci_slot', instead adding 'struct sqhci_host', which is only used by software queue.

Changes from v1:
- Add request_done ops for sdhci_ops.
- Replace virtual command queue with software queue for functions and variables.
- Rename the software queue file and add sqhci.h header file.

Quoted 5 lines
Quoted 2 lines

Do you have any comments for this patch set except the random config building issue that will be fixed in the next version? Thanks.

Pedantically, swhci is not a host controller interface, so the name still seems inappropriate. Otherwise I haven't had time to look at it, sorry.

OK. I will talk with Ulf to think about a good name. Thanks.

Signature · 2 lines
Baolin Wang
Best Regards