Add driver for HiSilicon SPMI PMIC for Hikey 970
Subsystems (9)
Mauro Carvalho Chehab
maintainercover Add driver for HiSilicon SPMI PMIC for Hikey 970
The Hikey 970 board uses a different PMIC than the one found on Hikey 960.
This PMIC uses a SPMI board.
This patch series backport the OOT drivers from the Linaro's official tree for this board:
https://github.com/96boards-hikey/linux/tree/hikey970-v4.9
Porting them to upstream, cleaning up coding style issues, solving driver probing order and adding DT documentation.
I opted to not fold all patches into a single one, in order to:
- Preserve the authorship of the original authors;
- Keep a history of changes.
As this could be harder for people to review, I'll be replying to patch 00/32 with all patches folded. This should help reviewers to see the current code after the entire series is applied.
Mauro Carvalho Chehab (32):
spmi: get rid of a warning when built with W=1
spmi: hisi-spmi-controller: coding style fixup
mfd, regulator: get rid of unused code at HiSilicon SPMI PMIC
regulator: hisi_regulator_spmi: port it to upstream
mfd: hisi_pmic_spmi: deal with non-static functions
mfd: hisi_pmic_spmi: get rid of the static vars
spmi: hisi-spmi-controller: fix it to probe successfully
spmi: hisi-spmi-controller: fix a typo
spmi: hisi-spmi-controller: adjust whitespaces at defines
spmi: hisi-spmi-controller: use le32 macros where needed
spmi: hisi-spmi-controller: add debug when values are read/write mfd, regulator: coding style fixups at the HiSilicon SPMI PMIC code
spmi: add hisi-spmi-controller to the building system
mfd: Kconfig: fix a typo
spmi: hisi-spmi-controller: fix the dev_foo() logic
mfd: pmic: add drivers for hi6421v600
mfd: hi6421-spmi-pmic: get rid of unused OF properties
spmi: hi6421-spmi-pmic: cleanup OF properties
regulator: hi6421v600-regulator: cleanup struct hisi_regulator
regulator: hi6421v600-regulator: cleanup debug messages
regulator: hi6421v600-regulator: use shorter names for OF properties
regulator: hi6421v600-regulator: better handle modes regulator, mfd: change namespace for HiSilicon SPMI PMIC drivers
regulator: hi6421v600-regulator: convert to use get/set voltage_sel
regulator: hi6421v600-regulator: don't use usleep_range for
off_on_delay
regulator: hi6421v600-regulator: add a driver-specific debug macro
regulator: hi6421v600-regulator: initialize ramp_delay
regulator: hi6421v600-regulator: cleanup DT settings
mfd, spmi, regulator: fix some coding style issues at HiSilicon SPMI
PMIC
dt: document HiSilicon SPMI controller and mfd/regulator properties
dt: hisilicon: add support for the PMIC found on Hikey 970
MAINTAINERS: add an entry for HiSilicon 6421v600 drivers
Mayulong (1):
spmi, regulator, mfd: add drivers for hikey970 SPMI PMIC
.../mfd/hisilicon,hi6421-spmi-pmic.yaml | 175 +++++++ .../spmi/hisilicon,hisi-spmi-controller.yaml | 54 ++ MAINTAINERS | 8 + .../boot/dts/hisilicon/hi3670-hikey970.dts | 16 +- .../boot/dts/hisilicon/hikey970-pmic.dtsi | 200 +++++++ drivers/mfd/Kconfig | 17 +- drivers/mfd/Makefile | 1 + drivers/mfd/hi6421-spmi-pmic.c | 399 ++++++++++++++ drivers/regulator/Kconfig | 8 + drivers/regulator/Makefile | 1 + drivers/regulator/hi6421v600-regulator.c | 493 ++++++++++++++++++ drivers/spmi/Kconfig | 9 + drivers/spmi/Makefile | 2 + drivers/spmi/hisi-spmi-controller.c | 384 ++++++++++++++ drivers/spmi/spmi.c | 10 +- include/linux/mfd/hi6421-spmi-pmic.h | 67 +++ 16 files changed, 1826 insertions(+), 18 deletions(-) create mode 100644 Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml create mode 100644 Documentation/devicetree/bindings/spmi/hisilicon,hisi-spmi-controller.yaml create mode 100644 arch/arm64/boot/dts/hisilicon/hikey970-pmic.dtsi create mode 100644 drivers/mfd/hi6421-spmi-pmic.c create mode 100644 drivers/regulator/hi6421v600-regulator.c create mode 100644 drivers/spmi/hisi-spmi-controller.c create mode 100644 include/linux/mfd/hi6421-spmi-pmic.h
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 31/33 dt: document HiSilicon SPMI controller and mfd/regulator properties
Add documentation for the properties needed by the HiSilicon 6421v600 driver, and by the SPMI controller used to access the chipset.
--- .../mfd/hisilicon,hi6421-spmi-pmic.yaml | 175 ++++++++++++++++++ .../spmi/hisilicon,hisi-spmi-controller.yaml | 54 ++++++ 2 files changed, 229 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml create mode 100644 Documentation/devicetree/bindings/spmi/hisilicon,hisi-spmi-controller.yaml
Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml new file +175 -0
@@ -0,0 +1,175 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/hisilicon,hi6421v600-regulator.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: HiSilicon 6421v600 SPMI PMIC + +maintainers: + - Mauro Carvalho Chehab <[email protected]> + +description: | + HiSilicon 6421v600 uses a MIPI System Power Management (SPMI) bus in order + to provide interrupts and power supply. + + The GPIO and interrupt settings are represented as part of the top-level PMIC + node. + + The SPMI controller part is provided by + Documentation/devicetree/bindings/spmi/hisilicon,hisi-spmi-controller.yaml. + +properties: + $nodename: + pattern: "pmic@[0-9a-f]" + + compatible: + const: hisilicon,hi6421-spmi-pmic + + reg: + maxItems: 1 + + spmi-channel: + description: number of the SPMI channel where the PMIC is connected + + '#interrupt-cells': + const: 2 + + interrupt-controller: + description: + Identify that the PMIC is capable of behaving as an interrupt controller. + + gpios: + maxItems: 1 + + irq-num: + description: Interrupt request number + + 'irq-array': + description: Interrupt request array + + 'irq-mask-addr': + description: Address for the interrupt request mask + + 'irq-addr': + description: Address for the interrupt request + + regulators: + type: object + + properties: + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + patternProperties: + '^ldo@[0-9]+$': + type: object + + $ref: "/schemas/regulator/regulator.yaml#" + + properties: + reg: + description: Enable register. + + vsel-reg: + description: Voltage selector register. + + enable-mask: + description: Bitmask used to enable the regulator. + +# voltage-table: +# description: Table with the selector items for the voltage regulator. +# minItems: 2 +# maxItems: 16 + + off-on-delay-us: + description: Time required for changing state to enabled in microseconds. + + startup-delay-us: + description: Startup time in microseconds. + + idle-mode-mask: + description: Bitmask used to put the regulator on idle mode. + + eco-microamp: + description: Maximum current while on idle mode. + + required: + - reg + - vsel-reg + - enable-mask + - voltage-table + - off-on-delay-us + - startup-delay-us + +required: + - compatible + - reg + - spmi-channel + - regulators + +examples: + - | + pmic: pmic@0 { + compatible = "hisilicon,hi6421-spmi-pmic"; + slave_id = <0>; + reg = <0 0>; + + #interrupt-cells = <2>; + interrupt-controller; + gpios = <&gpio28 0 0>; + irq-num = <16>; + irq-array = <2>; + irq-mask-addr = <0x202 2>; + irq-addr = <0x212 2>; + + regulators { + ldo3: ldo3@16 { + reg = <0x16>; + vsel-reg = <0x51>; + + regulator-name = "ldo3"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <2000000>; + regulator-boot-on; + + enable-mask = <0x01>; + + voltage-table = <1500000>, <1550000>, + <1600000>, <1650000>, + <1700000>, <1725000>, + <1750000>, <1775000>, + <1800000>, <1825000>, + <1850000>, <1875000>, + <1900000>, <1925000>, + <1950000>, <2000000>; + off-on-delay-us = <20000>; + startup-delay-us = <120>; + }; + + ldo4: ldo4@17 { /* 40 PIN */ + reg = <0x17>; + vsel-reg = <0x52>; + + regulator-name = "ldo4"; + regulator-min-microvolt = <1725000>; + regulator-max-microvolt = <1900000>; + regulator-boot-on; + + enable-mask = <0x01>; + idle-mode-mask = <0x10>; + eco-microamp = <10000>; + + hi6421-vsel = <0x52 0x07>; + voltage-table = <1725000>, <1750000>, + <1775000>, <1800000>, + <1825000>, <1850000>, + <1875000>, <1900000>; + off-on-delay-us = <20000>; + startup-delay-us = <120>; + }; + }; + };
Documentation/devicetree/bindings/spmi/hisilicon,hisi-spmi-controller.yaml new file +54 -0
54 lines not on this page · raw message
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 5/33 regulator: hisi_regulator_spmi: port it to upstream
In reply to Mauro Carvalho ChehabThe driver was originally written for Kernel 4.9. It needs to be ported to upstream:
- Got rid of timeval;
- Removed a bogus dependency;
- Did cleanups at the header file.
--- drivers/regulator/hisi_regulator_spmi.c | 34 ++++--------------------- include/linux/mfd/hisi_pmic.h | 26 ------------------- 2 files changed, 5 insertions(+), 55 deletions(-)
drivers/regulator/hisi_regulator_spmi.c +5 -29
@@ -49,7 +49,6 @@ struct hisi_regulator_register_info {struct hisi_regulator {const char *name;struct hisi_regulator_register_info register_info; -struct timeval last_off_time;u32 off_on_delay;u32 eco_uA;struct regulator_desc rdesc;
@@ -57,8 +56,6 @@ struct hisi_regulator { };static DEFINE_MUTEX (enable_mutex); -struct timeval last_enabled; -static inline struct hisi_pmic *rdev_to_pmic (struct regulator_dev *dev) {
@@ -72,27 +69,6 @@ static inline struct hisi_pmic *rdev_to_pmic(struct regulator_dev *dev)/* helper function to ensure when it returns it is at least 'delay_us' * microseconds after 'since'. */ -static void ensured_time_after (struct timeval since,u32 delay_us) -{ -struct timeval now; -u64 elapsed_ns64, delay_ns64; -u32 actual_us32; - - delay_ns64 = delay_us *NSEC_PER_USEC ; -do_gettimeofday (&now); - elapsed_ns64 =timeval_to_ns (&now) -timeval_to_ns (&since); -if (delay_ns64 > elapsed_ns64) { - actual_us32 = ((u32)(delay_ns64 - elapsed_ns64) / -NSEC_PER_USEC ); -if (actual_us32 >=1000 ) { -mdelay (actual_us32 /1000 );/*lint !e647 */ -udelay (actual_us32 %1000 ); - }else if (actual_us32 >0 ) { -udelay (actual_us32); - } - } -return ; -}static int hisi_regulator_is_enabled (struct regulator_dev *dev) {
@@ -113,13 +89,16 @@ static int hisi_regulator_enable(struct regulator_dev *dev)struct hisi_pmic *pmic =rdev_to_pmic (dev);/* keep a distance of off_on_delay from last time disabled */ -ensured_time_after (sreg->last_off_time, sreg->off_on_delay); +usleep_range (sreg->off_on_delay, sreg->off_on_delay +1000 );pr_debug ("<[%s]: off_on_delay=%dus>\n" , __func__, sreg->off_on_delay);/* cannot enable more than one regulator at one time */ mutex_lock (&enable_mutex); -ensured_time_after (last_enabled,HISI_REGS_ENA_PROTECT_TIME ); +usleep_range (HISI_REGS_ENA_PROTECT_TIME , +HISI_REGS_ENA_PROTECT_TIME +1000 ); + +/* set enable register */ hisi_pmic_rmw(pmic, sreg->register_info.ctrl_reg,
@@ -128,7 +107,6 @@ static int hisi_regulator_enable(struct regulator_dev *dev)pr_debug ("<[%s]: ctrl_reg=0x%x,enable_mask=0x%x>\n" , __func__, sreg->register_info.ctrl_reg,\ sreg->register_info.enable_mask); -do_gettimeofday (&last_enabled);mutex_unlock (&enable_mutex);return 0 ;
@@ -143,8 +121,6 @@ static int hisi_regulator_disable(struct regulator_dev *dev)hisi_pmic_rmw (pmic, sreg->register_info.ctrl_reg, sreg->register_info.enable_mask,0 ); -do_gettimeofday (&sreg->last_off_time); -return 0 ; }
include/linux/mfd/hisi_pmic.h +0 -26
@@ -73,34 +73,9 @@ struct hisi_pmic {struct write_lock debug_lock; }; -/* 0:disable; 1:enable */ -unsigned int get_uv_mntn_status (void ); -void clear_uv_mntn_resered_reg_bit (void ); -void set_uv_mntn_resered_reg_bit (void ); - -/* Register Access Helpers */ u32 hisi_pmic_read (struct hisi_pmic *pmic,int reg);void hisi_pmic_write (struct hisi_pmic *pmic,int reg,u32 val);void hisi_pmic_rmw (struct hisi_pmic *pmic,int reg,u32 mask,u32 bits); -unsigned int hisi_pmic_reg_read (int addr); -void hisi_pmic_reg_write (int addr,int val); -void hisi_pmic_reg_write_lock (int addr,int val); -int hisi_pmic_array_read (int addr,char *buff,unsigned int len); -int hisi_pmic_array_write (int addr,char *buff,unsigned int len); -extern int hisi_get_pmic_irq_byname (unsigned int pmic_irq_list); -extern int hisi_pmic_get_vbus_status (void ); -static inline u32 hisi_pmic_read (struct hisi_pmic *pmic,int reg) {return 0 ; } -static inline void hisi_pmic_write (struct hisi_pmic *pmic,int reg,u32 val) {} -static inline void hisi_pmic_rmw (struct hisi_pmic *pmic,int reg,u32 mask,u32 bits) {} -static inline unsigned int hisi_pmic_reg_read (int addr) {return 0 ; } -static inline void hisi_pmic_reg_write (int addr,int val) {} -static inline void hisi_pmic_reg_write_lock (int addr,int val) {} -static inline int hisi_pmic_array_read (int addr,char *buff,unsigned int len) {return 0 ; } -static inline int hisi_pmic_array_write (int addr,char *buff,unsigned int len) {return 0 ; } -static inline int hisi_get_pmic_irq_byname (unsigned int pmic_irq_list) {return -1 ; } -static inline int hisi_pmic_get_vbus_status (void ) {return 1 ; } -static inline u32 hisi_pmic_read_sub_pmu (u8 sid ,int reg) {return 0 ; } -static inline void hisi_pmic_write_sub_pmu (u8 sid ,int reg,u32 val) {}enum pmic_irq_list {OTMP =0 ,
@@ -120,4 +95,3 @@ enum pmic_irq_list { PMIC_IRQ_LIST_MAX, };#endif /* __HISI_PMIC_H */ -
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 10/33 spmi: hisi-spmi-controller: adjust whitespaces at defines
In reply to Mauro Carvalho ChehabSome defines are not aligned with tab=8, which is the style defined on Linux. Adjust them.
--- drivers/spmi/hisi-spmi-controller.c | 26 ++++++++++++++------------ 1 file changed, 14 insertions(+), 12 deletions(-)
drivers/spmi/hisi-spmi-controller.c +14 -12
@@ -18,10 +18,10 @@/* * SPMI register addr */ -#define SPMI_CHANNEL_OFFSET 0x0300 -#define SPMI_SLAVE_OFFSET 0x20 +#define SPMI_CHANNEL_OFFSET 0x0300 +#define SPMI_SLAVE_OFFSET 0x20 -#define SPMI_APB_SPMI_CMD_BASE_ADDR 0x0100 +#define SPMI_APB_SPMI_CMD_BASE_ADDR 0x0100#define SPMI_APB_SPMI_WDATA0_BASE_ADDR 0x0104#define SPMI_APB_SPMI_WDATA1_BASE_ADDR 0x0108
@@ -35,21 +35,21 @@#define SPMI_APB_SPMI_RDATA2_BASE_ADDR 0x020c#define SPMI_APB_SPMI_RDATA3_BASE_ADDR 0x0210 -#define SPMI_PER_DATAREG_BYTE 4 +#define SPMI_PER_DATAREG_BYTE 4/* * SPMI cmd register */ -#define SPMI_APB_SPMI_CMD_EN BIT(31) +#define SPMI_APB_SPMI_CMD_EN BIT(31)#define SPMI_APB_SPMI_CMD_TYPE_OFFSET 24#define SPMI_APB_SPMI_CMD_LENGTH_OFFSET 20 -#define SPMI_APB_SPMI_CMD_SLAVEID_OFFSET 16 -#define SPMI_APB_SPMI_CMD_ADDR_OFFSET 0#define bswap_32 (X ) \ ((((u32)(X) & 0xff000000) >> 24) | \ (((u32)(X) & 0x00ff0000) >> 8) | \ (((u32)(X) & 0x0000ff00) << 8) | \ (((u32)(X) & 0x000000ff) << 24)) +#define SPMI_APB_SPMI_CMD_SLAVEID_OFFSET 16 +#define SPMI_APB_SPMI_CMD_ADDR_OFFSET 0/* Command Opcodes */
@@ -70,15 +70,15 @@ enum spmi_controller_cmd_op_code {/* * SPMI status register */ -#define SPMI_APB_TRANS_DONE BIT(0) -#define SPMI_APB_TRANS_FAIL BIT(2) +#define SPMI_APB_TRANS_DONE BIT(0) +#define SPMI_APB_TRANS_FAIL BIT(2)/* Command register fields */ #define SPMI_CONTROLLER_CMD_MAX_BYTE_COUNT 16/* Maximum number of support PMIC peripherals */ #define SPMI_CONTROLLER_TIMEOUT_US 1000 -#define SPMI_CONTROLLER_MAX_TRANS_BYTES (16) +#define SPMI_CONTROLLER_MAX_TRANS_BYTES 16/* * @base base address of the PMIC Arbiter core registers.
@@ -114,8 +114,10 @@ static int spmi_controller_wait_for_done(struct spmi_controller_dev *ctrl_dev, {u32 status =0 ;u32 timeout =SPMI_CONTROLLER_TIMEOUT_US ; -u32 offset =SPMI_APB_SPMI_STATUS_BASE_ADDR +SPMI_CHANNEL_OFFSET * ctrl_dev->channel - +SPMI_SLAVE_OFFSET * sid; +u32 offset; + + offset =SPMI_APB_SPMI_STATUS_BASE_ADDR ; + offset +=SPMI_CHANNEL_OFFSET * ctrl_dev->channel +SPMI_SLAVE_OFFSET * sid;while (timeout--) { status =readl (base + offset);
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 32/33 dt: hisilicon: add support for the PMIC found on Hikey 970
In reply to Mauro Carvalho ChehabAdd a device tree for the HiSilicon 6421v600 SPMI PMIC, used on HiKey970 board.
As we now have support for it, change the fixed regulators used by the SD I/O to use the proper LDO supplies.
We'll keep the 3v3 fixed regulator, as this will be used by the DRM/KMS driver. So, let's just rename it.
--- .../boot/dts/hisilicon/hi3670-hikey970.dts | 16 +- .../boot/dts/hisilicon/hikey970-pmic.dtsi | 200 ++++++++++++++++++ 2 files changed, 204 insertions(+), 12 deletions(-) create mode 100644 arch/arm64/boot/dts/hisilicon/hikey970-pmic.dtsi
arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts +4 -12
@@ -12,6 +12,7 @@ #include "hi3670.dtsi" #include "hikey970-pinctrl.dtsi" +#include "hikey970-pmic.dtsi" / { model = "HiKey970";
@@ -39,7 +40,7 @@ memory@0 { reg = <0x0 0x0 0x0 0x0>; }; - sd_1v8: regulator-1v8 { + fixed_1v8: regulator-1v8 { compatible = "regulator-fixed"; regulator-name = "fixed-1.8V"; regulator-min-microvolt = <1800000>;
@@ -47,15 +48,6 @@ sd_1v8: regulator-1v8 { regulator-always-on; }; - sd_3v3: regulator-3v3 { - compatible = "regulator-fixed"; - regulator-name = "fixed-3.3V"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-boot-on; - regulator-always-on; - }; - wlan_en: wlan-en-1-8v { compatible = "regulator-fixed"; regulator-name = "wlan-en-regulator";
@@ -402,8 +394,8 @@ &dwmmc1 { pinctrl-0 = <&sd_pmx_func &sd_clk_cfg_func &sd_cfg_func>; - vmmc-supply = <&sd_3v3>; - vqmmc-supply = <&sd_1v8>; + vmmc-supply = <&ldo16>; + vqmmc-supply = <&ldo9>; status = "okay"; };
arch/arm64/boot/dts/hisilicon/hikey970-pmic.dtsi new file +200 -0
200 lines not on this page · raw message
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 17/33 mfd: pmic: add drivers for hi6421v600
In reply to Mauro Carvalho ChehabRename the code to better match other upstream drivers, and change the binding logic to ensure that the PMIC SPMI driver will run before the regulator code.
---
drivers/mfd/Kconfig | 15 ++
drivers/mfd/Makefile | 1 +
.../{hisi_pmic_spmi.c => hi6421-spmi-pmic.c} | 84 +++-----
drivers/regulator/Kconfig | 8 +
drivers/regulator/Makefile | 1 +
...egulator_spmi.c => hi6421v600-regulator.c} | 186 +++++++++---------
.../mfd/{hisi_pmic.h => hi6421-spmi-pmic.h} | 0
7 files changed, 145 insertions(+), 150 deletions(-)
rename drivers/mfd/{hisi_pmic_spmi.c => hi6421-spmi-pmic.c} (91%)
rename drivers/regulator/{hisi_regulator_spmi.c => hi6421v600-regulator.c} (80%)
rename include/linux/mfd/{hisi_pmic.h => hi6421-spmi-pmic.h} (100%)drivers/mfd/Kconfig +15 -0
@@ -497,6 +497,21 @@ config MFD_HI6421_PMIC menus in order to enable them. We communicate with the Hi6421 via memory-mapped I/O. +config MFD_HI6421_SPMI + tristate "HiSilicon Hi6421v600 SPMI PMU/Codec IC" + depends on OF + select MFD_CORE + select REGMAP_MMIO + help + Add support for HiSilicon Hi6421v600 SPMI PMIC. Hi6421 includes + multi-functions, such as regulators, RTC, codec, Coulomb counter, + etc. + + This driver includes core APIs _only_. You have to select + individual components like voltage regulators under corresponding + menus in order to enable them. + We communicate with the Hi6421v600 via a SPMI bus. + config MFD_HI655X_PMIC tristate "HiSilicon Hi655X series PMU/Codec IC" depends on ARCH_HISI || COMPILE_TEST
drivers/mfd/Makefile +1 -0
@@ -233,6 +233,7 @@ obj-$(CONFIG_MFD_IPAQ_MICRO) += ipaq-micro.o obj-$(CONFIG_MFD_IQS62X) += iqs62x.o obj-$(CONFIG_MFD_MENF21BMC) += menf21bmc.o obj-$(CONFIG_MFD_HI6421_PMIC) += hi6421-pmic-core.o +obj-$(CONFIG_MFD_HI6421_SPMI) += hi6421-spmi-pmic.o obj-$(CONFIG_MFD_HI655X_PMIC) += hi655x-pmic.o obj-$(CONFIG_MFD_DLN2) += dln2.o obj-$(CONFIG_MFD_RT5033) += rt5033.o
drivers/mfd/hi6421-spmi-pmic.c renamed from drivers/mfd/hisi_pmic_spmi.c +29 -55
120 lines not on this page · raw message
drivers/regulator/Kconfig +8 -0
@@ -356,6 +356,14 @@ config REGULATOR_HI6421V530 provides 5 general purpose LDOs, and all of them come with support to either ECO (idle) or sleep mode. +config REGULATOR_HI6421V600 + tristate "HiSilicon Hi6421v600 PMIC voltage regulator support" + depends on MFD_HI6421_PMIC && OF + help + This driver provides support for the voltage regulators on + HiSilicon Hi6421v600 PMU / Codec IC. + This is used on Kirin 3670 boards, like HiKey 970. + config REGULATOR_HI655X tristate "Hisilicon HI655X PMIC regulators support" depends on ARCH_HISI || COMPILE_TEST
drivers/regulator/Makefile +1 -0
@@ -44,6 +44,7 @@ obj-$(CONFIG_REGULATOR_FAN53555) += fan53555.o obj-$(CONFIG_REGULATOR_GPIO) += gpio-regulator.o obj-$(CONFIG_REGULATOR_HI6421) += hi6421-regulator.o obj-$(CONFIG_REGULATOR_HI6421V530) += hi6421v530-regulator.o +obj-$(CONFIG_REGULATOR_HI6421V600) += hi6421v600-regulator.o obj-$(CONFIG_REGULATOR_HI655X) += hi655x-regulator.o obj-$(CONFIG_REGULATOR_ISL6271A) += isl6271a-regulator.o obj-$(CONFIG_REGULATOR_ISL9305) += isl9305.o
drivers/regulator/hi6421v600-regulator.c renamed from drivers/regulator/hisi_regulator_spmi.c +91 -95
318 lines not on this page · raw message
include/linux/mfd/hi6421-spmi-pmic.h renamed from include/linux/mfd/hisi_pmic.h +0 -0
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 1/33 spmi: get rid of a warning when built with W=1
In reply to Mauro Carvalho ChehabThe SPMI core complaing with this warning when built with W=1:
drivers/spmi/spmi.c: In function ‘spmi_controller_remove’: drivers/spmi/spmi.c:548:6: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable] 548 | int dummy; | ^~~~~
As the dummy var isn't needed, remove it.
--- drivers/spmi/spmi.c | 5 +---- 1 file changed, 1 insertion(+), 4 deletions(-)
drivers/spmi/spmi.c +1 -4
@@ -545,13 +545,10 @@ static int spmi_ctrl_remove_device(struct device *dev, void *data)*/ void spmi_controller_remove (struct spmi_controller *ctrl) { -int dummy; -if (!ctrl)return ; - dummy =device_for_each_child (&ctrl->dev,NULL , - spmi_ctrl_remove_device); +device_for_each_child (&ctrl->dev,NULL , spmi_ctrl_remove_device);device_del (&ctrl->dev); }EXPORT_SYMBOL_GPL (spmi_controller_remove);
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 30/33 mfd, spmi, regulator: fix some coding style issues at HiSilicon SPMI PMIC
In reply to Mauro Carvalho ChehabCheckpatch complains about some minor issues inside the new mft/regulator/spmi drivers for HiSilicon 6421v600.
Address them.
--- drivers/mfd/hi6421-spmi-pmic.c | 4 ++-- drivers/regulator/hi6421v600-regulator.c | 28 ++++++++++++------------ drivers/spmi/spmi.c | 5 ++++- include/linux/mfd/hi6421-spmi-pmic.h | 3 ++- 4 files changed, 22 insertions(+), 18 deletions(-)
drivers/mfd/hi6421-spmi-pmic.c +2 -2
@@ -189,7 +189,7 @@ static struct irq_chip hi6421_spmi_pmu_irqchip = { };static int hi6421_spmi_irq_map (struct irq_domain *d,unsigned int virq, -irq_hw_number_t hw) +irq_hw_number_t hw) {struct hi6421_spmi_pmic *pmic = d->host_data;
@@ -350,7 +350,7 @@ static int hi6421_spmi_pmic_probe(struct spmi_device *pdev)* The logic below will rely that the pmic is already stored at * drvdata. */ -dev_dbg (&pdev->dev,"SPMI-PMIC: adding childs for %pOF\n" , +dev_dbg (&pdev->dev,"SPMI-PMIC: adding children for %pOF\n" , pdev->dev.of_node); ret = devm_mfd_add_devices(&pdev->dev, PLATFORM_DEVID_NONE, hi6421v600_devs, ARRAY_SIZE(hi6421v600_devs),
drivers/regulator/hi6421v600-regulator.c +14 -14
@@ -40,7 +40,7 @@#include <linux/spmi.h> #define rdev_dbg(rdev, fmt, arg...) \ - pr_debug("%s: %s: " fmt, rdev->desc->name, __func__, ##arg) + pr_debug("%s: %s: " fmt, (rdev)->desc->name, __func__, ##arg)struct hi6421v600_regulator {struct regulator_desc rdesc;
@@ -105,7 +105,7 @@ static int hi6421_spmi_regulator_disable(struct regulator_dev *rdev) rdev->desc->enable_reg, rdev->desc->enable_mask);hi6421_spmi_pmic_rmw (pmic, rdev->desc->enable_reg, - rdev->desc->enable_mask,0 ); + rdev->desc->enable_mask,0 );return 0 ; }
@@ -122,7 +122,7 @@ static int hi6421_spmi_regulator_get_voltage_sel(struct regulator_dev *rdev) selector = (reg_val & rdev->desc->vsel_mask) >> (ffs (rdev->desc->vsel_mask) -1 );rdev_dbg (rdev, -"vsel_reg=0x%x, value=0x%x, entry=0x%x, voltage=%d mV\n" , +"vsel_reg=0x%x, value=0x%x, entry=0x%x, voltage=%d mV\n" , rdev->desc->vsel_reg, reg_val, selector, rdev->desc->ops->list_voltage (rdev, selector) /1000 );
@@ -144,7 +144,7 @@ static int hi6421_spmi_regulator_set_voltage_sel(struct regulator_dev *rdev,/* set voltage selector */ rdev_dbg (rdev, -"vsel_reg=0x%x, mask=0x%x, value=0x%x, voltage=%d mV\n" , +"vsel_reg=0x%x, mask=0x%x, value=0x%x, voltage=%d mV\n" , rdev->desc->vsel_reg, rdev->desc->vsel_mask, reg_val, rdev->desc->ops->list_voltage (rdev, selector) /1000 );
@@ -169,7 +169,7 @@ static unsigned int hi6421_spmi_regulator_get_mode(struct regulator_dev *rdev) mode =REGULATOR_MODE_NORMAL ;rdev_dbg (rdev, -"enable_reg=0x%x, eco_mode_mask=0x%x, reg_val=0x%x, %s mode\n" , +"enable_reg=0x%x, eco_mode_mask=0x%x, reg_val=0x%x, %s mode\n" , rdev->desc->enable_reg, sreg->eco_mode_mask, reg_val, mode ==REGULATOR_MODE_IDLE ?"idle" :"normal" );
@@ -177,7 +177,7 @@ static unsigned int hi6421_spmi_regulator_get_mode(struct regulator_dev *rdev) }static int hi6421_spmi_regulator_set_mode (struct regulator_dev *rdev, -unsigned int mode) +unsigned int mode) {struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev);struct hi6421_spmi_pmic *pmic = sreg->pmic;
@@ -204,9 +204,10 @@ static int hi6421_spmi_regulator_set_mode(struct regulator_dev *rdev,return 0 ; } -static unsigned int hi6421_spmi_regulator_get_optimum_mode (struct regulator_dev *rdev, -int input_uV,int output_uV, -int load_uA) +static unsigned int +hi6421_spmi_regulator_get_optimum_mode (struct regulator_dev *rdev, +int input_uV,int output_uV, +int load_uA) {struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev);
@@ -220,7 +221,7 @@ static unsigned int hi6421_spmi_regulator_get_optimum_mode(struct regulator_dev }static int hi6421_spmi_dt_parse (struct platform_device *pdev, -struct hi6421v600_regulator *sreg, +struct hi6421v600_regulator *sreg,struct regulator_desc *rdesc) {struct device *dev = &pdev->dev;
@@ -256,7 +257,7 @@ static int hi6421_spmi_dt_parse(struct platform_device *pdev, sreg->eco_uA =0 ; }else { ret =of_property_read_u32 (np,"eco-microamp" , - &sreg->eco_uA); + &sreg->eco_uA);if (ret) {dev_err (dev,"missing eco-microamp property\n" );return ret;
@@ -331,8 +332,8 @@ static struct regulator_ops hi6421_spmi_ldo_rops = {*/ static int hi6421_spmi_regulator_probe_ldo (struct platform_device *pdev, -struct device_node *np, -struct hi6421_spmi_pmic *pmic) +struct device_node *np, +struct hi6421_spmi_pmic *pmic) {struct device *dev = &pdev->dev;struct regulator_desc *rdesc;
@@ -404,7 +405,6 @@ static int hi6421_spmi_regulator_probe_ldo(struct platform_device *pdev,return ret; } -static int hi6421_spmi_regulator_probe (struct platform_device *pdev) {struct device *pmic_dev = pdev->dev.parent;
drivers/spmi/spmi.c +4 -1
@@ -23,6 +23,7 @@ static DEFINE_IDA(ctrl_ida);static void spmi_dev_release (struct device *dev) {struct spmi_device *sdev =to_spmi_device (dev); +kfree (sdev); }
@@ -33,6 +34,7 @@ static const struct device_type spmi_dev_type = {static void spmi_ctrl_release (struct device *dev) {struct spmi_controller *ctrl =to_spmi_controller (dev); +ida_simple_remove (&ctrl_ida, ctrl->nr);kfree (ctrl); }
@@ -487,7 +489,7 @@ static void of_spmi_register_devices(struct spmi_controller *ctrl)continue ; sdev->dev.of_node = node; - sdev->usid = (u8 ) reg[0 ]; + sdev->usid = (u8 )reg[0 ]; err =spmi_device_add (sdev);if (err) {
@@ -531,6 +533,7 @@ EXPORT_SYMBOL_GPL(spmi_controller_add);static int spmi_ctrl_remove_device (struct device *dev,void *data) {struct spmi_device *spmidev =to_spmi_device (dev); +if (dev->type == &spmi_dev_type)spmi_device_remove (spmidev);return 0 ;
include/linux/mfd/hi6421-spmi-pmic.h +2 -1
@@ -38,7 +38,8 @@ struct hi6421_spmi_pmic {unsigned int *irqs;int irqnum;int irqarray; -struct hi6421_spmi_irq_mask_info irq_mask_addr; + +struct hi6421_spmi_irq_mask_info irq_mask_addr;struct hi6421_spmi_irq_info irq_addr; };
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 27/33 regulator: hi6421v600-regulator: add a driver-specific debug macro
In reply to Mauro Carvalho ChehabUsing dev_dbg() is not too nice, as, instead of printing the name of the regulator, it prints "regulator.<number>", making harder to associate what is happening with each ldo line.
So, add a debug-specific macro, which will print the rdev's name, just like the regulator core.
--- drivers/regulator/hi6421v600-regulator.c | 61 +++++++++++++----------- 1 file changed, 32 insertions(+), 29 deletions(-)
drivers/regulator/hi6421v600-regulator.c +32 -29
@@ -39,6 +39,9 @@#include <linux/uaccess.h> #include <linux/spmi.h> +#define rdev_dbg(rdev, fmt, arg...) \ + pr_debug("%s: %s: " fmt, rdev->desc->name, __func__, ##arg) +struct hi6421v600_regulator {struct regulator_desc rdesc;struct hi6421_spmi_pmic *pmic;
@@ -60,10 +63,10 @@ static int hi6421_spmi_regulator_is_enabled(struct regulator_dev *rdev) reg_val =hi6421_spmi_pmic_read (pmic, rdev->desc->enable_reg); -dev_dbg (&rdev->dev, -"%s: enable_reg=0x%x, val= 0x%x, enable_state=%d\n" , - __func__, rdev->desc->enable_reg, - reg_val, (reg_val & rdev->desc->enable_mask)); +rdev_dbg (rdev, +"enable_reg=0x%x, val= 0x%x, enable_state=%d\n" , + rdev->desc->enable_reg, + reg_val, (reg_val & rdev->desc->enable_mask));return ((reg_val & rdev->desc->enable_mask) !=0 ); }
@@ -73,21 +76,20 @@ static int hi6421_spmi_regulator_enable(struct regulator_dev *rdev)struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev);struct hi6421_spmi_pmic *pmic = sreg->pmic; -dev_dbg (&rdev->dev,"%s: off_on_delay=%d us\n" , - __func__, rdev->desc->off_on_delay); -/* cannot enable more than one regulator at one time */ mutex_lock (&enable_mutex);usleep_range (HISI_REGS_ENA_PROTECT_TIME ,HISI_REGS_ENA_PROTECT_TIME +1000 );/* set enable register */ +rdev_dbg (rdev, +"off_on_delay=%d us, enable_reg=0x%x, enable_mask=0x%x\n" , + rdev->desc->off_on_delay, rdev->desc->enable_reg, + rdev->desc->enable_mask); +hi6421_spmi_pmic_rmw (pmic, rdev->desc->enable_reg, rdev->desc->enable_mask, rdev->desc->enable_mask); -dev_dbg (&rdev->dev,"%s: enable_reg=0x%x, enable_mask=0x%x\n" , - __func__, rdev->desc->enable_reg, - rdev->desc->enable_mask);mutex_unlock (&enable_mutex);
@@ -100,6 +102,9 @@ static int hi6421_spmi_regulator_disable(struct regulator_dev *rdev)struct hi6421_spmi_pmic *pmic = sreg->pmic;/* set enable register to 0 */ +rdev_dbg (rdev,"enable_reg=0x%x, enable_mask=0x%x\n" , + rdev->desc->enable_reg, rdev->desc->enable_mask); +hi6421_spmi_pmic_rmw (pmic, rdev->desc->enable_reg, rdev->desc->enable_mask,0 );
@@ -117,9 +122,9 @@ static int hi6421_spmi_regulator_get_voltage_sel(struct regulator_dev *rdev) selector = (reg_val & rdev->desc->vsel_mask) >> (ffs (rdev->desc->vsel_mask) -1 ); -dev_dbg (&rdev->dev, -"%s: vsel_reg=0x%x, value=0x%x, entry=0x%x, voltage=%d mV\n" , - __func__, rdev->desc->vsel_reg, reg_val, selector, +rdev_dbg (rdev, +"vsel_reg=0x%x, value=0x%x, entry=0x%x, voltage=%d mV\n" , + rdev->desc->vsel_reg, reg_val, selector, rdev->desc->ops->list_voltage (rdev, selector) /1000 );return selector;
@@ -139,15 +144,14 @@ static int hi6421_spmi_regulator_set_voltage_sel(struct regulator_dev *rdev, reg_val = selector << (ffs (rdev->desc->vsel_mask) -1 );/* set voltage selector */ -hi6421_spmi_pmic_rmw (pmic, rdev->desc->vsel_reg, - rdev->desc->vsel_mask, reg_val); - -dev_dbg (&rdev->dev, -"%s: vsel_reg=0x%x, mask=0x%x, value=0x%x, voltage=%d mV\n" , - __func__, +rdev_dbg (rdev, +"vsel_reg=0x%x, mask=0x%x, value=0x%x, voltage=%d mV\n" , rdev->desc->vsel_reg, rdev->desc->vsel_mask, reg_val, rdev->desc->ops->list_voltage (rdev, selector) /1000 ); +hi6421_spmi_pmic_rmw (pmic, rdev->desc->vsel_reg, + rdev->desc->vsel_mask, reg_val); +return 0 ; }
@@ -165,9 +169,9 @@ static unsigned int hi6421_spmi_regulator_get_mode(struct regulator_dev *rdev)else mode =REGULATOR_MODE_NORMAL ; -dev_dbg (&rdev->dev, -"%s: enable_reg=0x%x, eco_mode_mask=0x%x, reg_val=0x%x, %s mode\n" , - __func__, rdev->desc->enable_reg, sreg->eco_mode_mask, reg_val, +rdev_dbg (rdev, +"enable_reg=0x%x, eco_mode_mask=0x%x, reg_val=0x%x, %s mode\n" , + rdev->desc->enable_reg, sreg->eco_mode_mask, reg_val, mode ==REGULATOR_MODE_IDLE ?"idle" :"normal" );return mode;
@@ -192,13 +196,12 @@ static int hi6421_spmi_regulator_set_mode(struct regulator_dev *rdev, }/* set mode */ +rdev_dbg (rdev,"enable_reg=0x%x, eco_mode_mask=0x%x, value=0x%x\n" , + rdev->desc->enable_reg, sreg->eco_mode_mask, val); +hi6421_spmi_pmic_rmw (pmic, rdev->desc->enable_reg, sreg->eco_mode_mask, val); -dev_dbg (&rdev->dev, -"%s: enable_reg=0x%x, eco_mode_mask=0x%x, value=0x%x\n" , - __func__, rdev->desc->enable_reg, sreg->eco_mode_mask, val); -return 0 ; }
@@ -209,10 +212,10 @@ static unsigned int hi6421_spmi_regulator_get_optimum_mode(struct regulator_devstruct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev);if (load_uA || ((unsigned int )load_uA > sreg->eco_uA)) { -dev_dbg (&rdev->dev,"%s: normal mode" , __func__); +rdev_dbg (rdev,"normal mode" );return REGULATOR_MODE_NORMAL ; }else { -dev_dbg (&rdev->dev,"%s: idle mode" , __func__); +rdev_dbg (rdev,"idle mode" );return REGULATOR_MODE_IDLE ; } }
@@ -373,7 +376,7 @@ static int hi6421_spmi_regulator_probe_ldo(struct platform_device *pdev, goto probe_end; } -dev_dbg (dev,"valid_modes_mask: 0x%x, valid_ops_mask: 0x%x\n" , +rdev_dbg (rdev,"valid_modes_mask: 0x%x, valid_ops_mask: 0x%x\n" , constraint->valid_modes_mask, constraint->valid_ops_mask);dev_set_drvdata (dev, rdev);
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 33/33 MAINTAINERS: add an entry for HiSilicon 6421v600 drivers
In reply to Mauro Carvalho ChehabAdd an entry for the SPMI, MFD and PMIC parts of the HiSilicon 6421v600 support.
--- MAINTAINERS | 8 ++++++++ 1 file changed, 8 insertions(+)
MAINTAINERS +8 -0
@@ -7736,6 +7736,14 @@ F: include/linux/hippidevice.h F: include/uapi/linux/if_hippi.h F: net/802/hippi.c +HISILICON 6421v600 SPMI PMIC DRIVER +M: Mauro Carvalho Chehab <[email protected]> +L: [email protected] +S: Maintained +F: drivers/mfd/hi6421-spmi-pmic.c +F: drivers/regulator/hi6421v600-regulator.c +F: drivers/spmi/spmi.c + HISILICON DMA DRIVER M: Zhou Wang <[email protected]> L: [email protected]
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 29/33 regulator: hi6421v600-regulator: cleanup DT settings
In reply to Mauro Carvalho ChehabCurrently, an array is used to store both vsel and enable settings, mixing registers, masks and bit settings.
Change it in order to have one separate property for each.
This makes easier to understand the contents of the DT file, and to describe it at the Documentation/.
--- drivers/regulator/hi6421v600-regulator.c | 69 ++++++++++++++---------- 1 file changed, 42 insertions(+), 27 deletions(-)
drivers/regulator/hi6421v600-regulator.c +42 -27
@@ -45,8 +45,7 @@struct hi6421v600_regulator {struct regulator_desc rdesc;struct hi6421_spmi_pmic *pmic; -u8 eco_mode_mask; -u32 eco_uA; +u32 eco_mode_mask, eco_uA; };static DEFINE_MUTEX (enable_mutex);
@@ -226,36 +225,49 @@ static int hi6421_spmi_dt_parse(struct platform_device *pdev, {struct device *dev = &pdev->dev;struct device_node *np = dev->of_node; -unsigned int register_info[3 ] = {0 };unsigned int *v_table;int ret; -/* parse .register_info.enable_reg */ - ret =of_property_read_u32_array (np,"hi6421-ctrl" , - register_info,3 ); + ret =of_property_read_u32 (np,"reg" , &rdesc->enable_reg);if (ret) { -dev_err (dev,"no hi6421-ctrl property set\n" ); +dev_err (dev,"missing reg property\nn" );return ret; } - rdesc->enable_reg = register_info[0 ]; - rdesc->enable_mask = register_info[1 ]; - sreg->eco_mode_mask = register_info[2 ]; -/* parse .register_info.vsel_reg */ - ret =of_property_read_u32_array (np,"hi6421-vsel" , - register_info,2 ); + ret =of_property_read_u32 (np,"vsel-reg" , &rdesc->vsel_reg);if (ret) { -dev_err (dev,"no hi6421-vsel property set\n" ); +dev_err (dev,"missing vsel-reg property\n" );return ret; } - rdesc->vsel_reg = register_info[0 ]; - rdesc->vsel_mask = register_info[1 ]; + + ret =of_property_read_u32 (np,"enable-mask" , &rdesc->enable_mask); +if (ret) { +dev_err (dev,"missing enable-mask property\n" ); +return ret; + } + +/* +* Not all regulators work on idle mode +*/ + ret =of_property_read_u32 (np,"idle-mode-mask" , &sreg->eco_mode_mask); +if (ret) { +dev_dbg (dev,"LDO doesn't support economy mode.\n" ); + sreg->eco_mode_mask =0 ; + sreg->eco_uA =0 ; + }else { + ret =of_property_read_u32 (np,"eco-microamp" , + &sreg->eco_uA); +if (ret) { +dev_err (dev,"missing eco-microamp property\n" ); +return ret; + } + }/* parse .off-on-delay */ ret =of_property_read_u32 (np,"off-on-delay-us" , &rdesc->off_on_delay);if (ret) { -dev_err (dev,"no off-on-delay-us property set\n" ); +dev_err (dev,"missing off-on-delay-us property\n" );return ret; }
@@ -263,21 +275,13 @@ static int hi6421_spmi_dt_parse(struct platform_device *pdev, ret =of_property_read_u32 (np,"startup-delay-us" , &rdesc->enable_time);if (ret) { -dev_err (dev,"no startup-delay-us property set\n" ); +dev_err (dev,"missing startup-delay-us property\n" );return ret; }/* FIXME: are there a better value for this? */ rdesc->ramp_delay = rdesc->enable_time; -/* parse .eco_uA */ - ret =of_property_read_u32 (np,"eco-microamp" , - &sreg->eco_uA); -if (ret) { - sreg->eco_uA =0 ; - ret =0 ; - } -/* parse volt_table */ rdesc->n_voltages =of_property_count_u32_elems (np,"voltage-table" );
@@ -291,10 +295,21 @@ static int hi6421_spmi_dt_parse(struct platform_device *pdev, ret =of_property_read_u32_array (np,"voltage-table" , v_table, rdesc->n_voltages);if (ret) { -dev_err (dev,"no voltage-table property set\n" ); +dev_err (dev,"missing voltage-table property\n" );return ret; } +/* +* Instead of explicitly requiring a mask for the voltage selector, +* as they all start from bit zero (at least on the known LDOs), +* just use the number of voltages at the voltage table, getting the +* minimal mask that would pick everything. +*/ + rdesc->vsel_mask = (1 << (fls (rdesc->n_voltages) -1 )) -1 ; + +dev_dbg (dev,"voltage selector settings: reg: 0x%x, mask: 0x%x" , + rdesc->vsel_reg, rdesc->vsel_mask); +return 0 ; }
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 24/33 regulator, mfd: change namespace for HiSilicon SPMI PMIC drivers
In reply to Mauro Carvalho ChehabRename the functions used internally inside the driver in order for them to follow the driver's name.
While here, get rid of some unused definitions at the header file.
--- drivers/mfd/hi6421-spmi-pmic.c | 97 +++++++++++++----------- drivers/regulator/hi6421v600-regulator.c | 94 +++++++++++------------ include/linux/mfd/hi6421-spmi-pmic.h | 51 +++++-------- 3 files changed, 117 insertions(+), 125 deletions(-)
drivers/mfd/hi6421-spmi-pmic.c +51 -46
@@ -62,7 +62,7 @@ static const struct mfd_cell hi6421v600_devs[] = {* Hisilicon SoC use hardware to map PMIC register into SoC mapping. * At here, we are accessing SoC register with 32-bit. */ -u32 hisi_pmic_read (struct hisi_pmic *pmic,int reg) +u32 hi6421_spmi_pmic_read (struct hi6421_spmi_pmic *pmic,int reg) {u32 ret;u8 read_value =0 ;
@@ -82,9 +82,9 @@ u32 hisi_pmic_read(struct hisi_pmic *pmic, int reg) }return (u32 )read_value; } -EXPORT_SYMBOL (hisi_pmic_read); +EXPORT_SYMBOL (hi6421_spmi_pmic_read); -void hisi_pmic_write (struct hisi_pmic *pmic,int reg,u32 val) +void hi6421_spmi_pmic_write (struct hi6421_spmi_pmic *pmic,int reg,u32 val) {u32 ret;struct spmi_device *pdev;
@@ -101,34 +101,36 @@ void hisi_pmic_write(struct hisi_pmic *pmic, int reg, u32 val)return ; } } -EXPORT_SYMBOL (hisi_pmic_write); +EXPORT_SYMBOL (hi6421_spmi_pmic_write); -void hisi_pmic_rmw (struct hisi_pmic *pmic,int reg,u32 mask,u32 bits) +void hi6421_spmi_pmic_rmw (struct hi6421_spmi_pmic *pmic,int reg, +u32 mask,u32 bits) {u32 data;unsigned long flags;spin_lock_irqsave (&pmic->lock, flags); - data =hisi_pmic_read (pmic, reg) & ~mask; + data =hi6421_spmi_pmic_read (pmic, reg) & ~mask; data |= mask & bits; -hisi_pmic_write (pmic, reg, data); +hi6421_spmi_pmic_write (pmic, reg, data);spin_unlock_irqrestore (&pmic->lock, flags); } -EXPORT_SYMBOL (hisi_pmic_rmw); +EXPORT_SYMBOL (hi6421_spmi_pmic_rmw); -static irqreturn_t hisi_irq_handler (int irq,void *data) +static irqreturn_t hi6421_spmi_irq_handler (int irq,void *data) { -struct hisi_pmic *pmic = (struct hisi_pmic *)data; +struct hi6421_spmi_pmic *pmic = (struct hi6421_spmi_pmic *)data;unsigned long pending;int i, offset;for (i =0 ; i < pmic->irqarray; i++) { - pending =hisi_pmic_read (pmic, (i + pmic->irq_addr.start_addr)); + pending =hi6421_spmi_pmic_read (pmic, (i + pmic->irq_addr.start_addr)); pending &=HISI_MASK_FIELD ;if (pending !=0 )pr_debug ("pending[%d]=0x%lx\n\r" , i, pending); -hisi_pmic_write (pmic, (i + pmic->irq_addr.start_addr), pending); +hi6421_spmi_pmic_write (pmic, (i + pmic->irq_addr.start_addr), + pending);/* solve powerkey order */ if ((i ==HISI_IRQ_KEY_NUM ) && ((pending &HISI_IRQ_KEY_VALUE ) ==HISI_IRQ_KEY_VALUE )) {
@@ -146,9 +148,9 @@ static irqreturn_t hisi_irq_handler(int irq, void *data)return IRQ_HANDLED ; } -static void hisi_irq_mask (struct irq_data *d) +static void hi6421_spmi_irq_mask (struct irq_data *d) { -struct hisi_pmic *pmic =irq_data_get_irq_chip_data (d); +struct hi6421_spmi_pmic *pmic =irq_data_get_irq_chip_data (d);u32 data, offset;unsigned long flags;
@@ -156,15 +158,15 @@ static void hisi_irq_mask(struct irq_data *d) offset += pmic->irq_mask_addr.start_addr;spin_lock_irqsave (&pmic->lock, flags); - data =hisi_pmic_read (pmic, offset); + data =hi6421_spmi_pmic_read (pmic, offset); data |= (1 << (irqd_to_hwirq (d) &0x07 )); -hisi_pmic_write (pmic, offset, data); +hi6421_spmi_pmic_write (pmic, offset, data);spin_unlock_irqrestore (&pmic->lock, flags); } -static void hisi_irq_unmask (struct irq_data *d) +static void hi6421_spmi_irq_unmask (struct irq_data *d) { -struct hisi_pmic *pmic =irq_data_get_irq_chip_data (d); +struct hi6421_spmi_pmic *pmic =irq_data_get_irq_chip_data (d);u32 data, offset;unsigned long flags;
@@ -172,26 +174,26 @@ static void hisi_irq_unmask(struct irq_data *d) offset += pmic->irq_mask_addr.start_addr;spin_lock_irqsave (&pmic->lock, flags); - data =hisi_pmic_read (pmic, offset); + data =hi6421_spmi_pmic_read (pmic, offset); data &= ~(1 << (irqd_to_hwirq (d) &0x07 )); -hisi_pmic_write (pmic, offset, data); +hi6421_spmi_pmic_write (pmic, offset, data);spin_unlock_irqrestore (&pmic->lock, flags); } -static struct irq_chip hisi_pmu_irqchip = { +static struct irq_chip hi6421_spmi_pmu_irqchip = { .name ="hisi-irq" , - .irq_mask = hisi_irq_mask, - .irq_unmask = hisi_irq_unmask, - .irq_disable = hisi_irq_mask, - .irq_enable = hisi_irq_unmask, + .irq_mask = hi6421_spmi_irq_mask, + .irq_unmask = hi6421_spmi_irq_unmask, + .irq_disable = hi6421_spmi_irq_mask, + .irq_enable = hi6421_spmi_irq_unmask, }; -static int hisi_irq_map (struct irq_domain *d,unsigned int virq, +static int hi6421_spmi_irq_map (struct irq_domain *d,unsigned int virq,irq_hw_number_t hw) { -struct hisi_pmic *pmic = d->host_data; +struct hi6421_spmi_pmic *pmic = d->host_data; -irq_set_chip_and_handler_name (virq, &hisi_pmu_irqchip, +irq_set_chip_and_handler_name (virq, &hi6421_spmi_pmu_irqchip, handle_simple_irq,"hisi" );irq_set_chip_data (virq, pmic);irq_set_irq_type (virq,IRQ_TYPE_NONE );
@@ -199,12 +201,13 @@ static int hisi_irq_map(struct irq_domain *d, unsigned int virq,return 0 ; } -static const struct irq_domain_ops hisi_domain_ops = { - .map = hisi_irq_map, +static const struct irq_domain_ops hi6421_spmi_domain_ops = { + .map = hi6421_spmi_irq_map, .xlate = irq_domain_xlate_twocell, }; -static int get_pmic_device_tree_data (struct device_node *np,struct hisi_pmic *pmic) +static int get_pmic_device_tree_data (struct device_node *np, +struct hi6421_spmi_pmic *pmic) {int ret =0 ;
@@ -247,27 +250,29 @@ static int get_pmic_device_tree_data(struct device_node *np, struct hisi_pmic *preturn ret; } -static void hisi_pmic_irq_prc (struct hisi_pmic *pmic) +static void hi6421_spmi_pmic_irq_prc (struct hi6421_spmi_pmic *pmic) {int i;for (i =0 ; i < pmic->irq_mask_addr.array; i++) -hisi_pmic_write (pmic, pmic->irq_mask_addr.start_addr + i,HISI_MASK_STATE ); +hi6421_spmi_pmic_write (pmic, pmic->irq_mask_addr.start_addr + i, +HISI_MASK_STATE );for (i =0 ; i < pmic->irq_addr.array; i++) { -unsigned int pending =hisi_pmic_read (pmic, pmic->irq_addr.start_addr + i); +unsigned int pending =hi6421_spmi_pmic_read (pmic, pmic->irq_addr.start_addr + i);pr_debug ("PMU IRQ address value:irq[0x%x] = 0x%x\n" , pmic->irq_addr.start_addr + i, pending); -hisi_pmic_write (pmic, pmic->irq_addr.start_addr + i,HISI_MASK_STATE ); +hi6421_spmi_pmic_write (pmic, pmic->irq_addr.start_addr + i, +HISI_MASK_STATE ); } } -static int hisi_pmic_probe (struct spmi_device *pdev) +static int hi6421_spmi_pmic_probe (struct spmi_device *pdev) {struct device *dev = &pdev->dev;struct device_node *np = dev->of_node; -struct hisi_pmic *pmic =NULL ; +struct hi6421_spmi_pmic *pmic =NULL ;enum of_gpio_flags flags;int ret =0 ;int i;
@@ -305,14 +310,14 @@ static int hisi_pmic_probe(struct spmi_device *pdev) pmic->irq =gpio_to_irq (pmic->gpio);/* mask && clear IRQ status */ -hisi_pmic_irq_prc (pmic); +hi6421_spmi_pmic_irq_prc (pmic); pmic->irqs =devm_kzalloc (dev, pmic->irqnum *sizeof (int ),GFP_KERNEL );if (!pmic->irqs) goto irq_malloc; pmic->domain =irq_domain_add_simple (np, pmic->irqnum,0 , - &hisi_domain_ops, pmic); + &hi6421_spmi_domain_ops, pmic);if (!pmic->domain) {dev_err (dev,"failed irq domain add simple!\n" ); ret = -ENODEV ;
@@ -330,7 +335,7 @@ static int hisi_pmic_probe(struct spmi_device *pdev)pr_info ("[%s]. pmic->irqs[%d] = %d\n" , __func__, i, pmic->irqs[i]); } - ret =request_threaded_irq (pmic->irq, hisi_irq_handler,NULL , + ret =request_threaded_irq (pmic->irq, hi6421_spmi_irq_handler,NULL ,IRQF_TRIGGER_LOW |IRQF_SHARED |IRQF_NO_SUSPEND ,"pmic" , pmic);if (ret <0 ) {
@@ -365,9 +370,9 @@ static int hisi_pmic_probe(struct spmi_device *pdev)return ret; } -static void hisi_pmic_remove (struct spmi_device *pdev) +static void hi6421_spmi_pmic_remove (struct spmi_device *pdev) { -struct hisi_pmic *pmic =dev_get_drvdata (&pdev->dev); +struct hi6421_spmi_pmic *pmic =dev_get_drvdata (&pdev->dev);free_irq (pmic->irq, pmic);gpio_free (pmic->gpio);
@@ -380,15 +385,15 @@ static const struct of_device_id pmic_spmi_id_table[] = { };MODULE_DEVICE_TABLE (of, pmic_spmi_id_table); -static struct spmi_driver hisi_pmic_driver = { +static struct spmi_driver hi6421_spmi_pmic_driver = { .driver = { .name ="hi6421-spmi-pmic" , .of_match_table = pmic_spmi_id_table, }, - .probe = hisi_pmic_probe, - .remove = hisi_pmic_remove, + .probe = hi6421_spmi_pmic_probe, + .remove = hi6421_spmi_pmic_remove, }; -module_spmi_driver (hisi_pmic_driver); +module_spmi_driver (hi6421_spmi_pmic_driver);MODULE_DESCRIPTION ("HiSilicon Hi6421v600 SPMI PMIC driver" );MODULE_LICENSE ("GPL v2" );
drivers/regulator/hi6421v600-regulator.c +47 -47
266 lines not on this page · raw message
include/linux/mfd/hi6421-spmi-pmic.h +19 -32
68 lines not on this page · raw message
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 2/33 spmi, regulator, mfd: add drivers for hikey970 SPMI PMIC
In reply to Mauro Carvalho ChehabFrom: Mayulong <[email protected]>
Add the SPMI controller code and the MFD/regulator drivers needed to support the PMIC used at the Hikey970 board.
[[email protected]: keep just the sources, removing Kbuild changes]
--- drivers/mfd/hisi_pmic_spmi.c | 759 ++++++++++++++++++++++++ drivers/regulator/hisi_regulator_spmi.c | 741 +++++++++++++++++++++++ drivers/spmi/hisi-spmi-controller.c | 390 ++++++++++++ include/linux/mfd/hisi_pmic.h | 165 ++++++ 4 files changed, 2055 insertions(+) create mode 100644 drivers/mfd/hisi_pmic_spmi.c create mode 100644 drivers/regulator/hisi_regulator_spmi.c create mode 100644 drivers/spmi/hisi-spmi-controller.c create mode 100644 include/linux/mfd/hisi_pmic.h
drivers/mfd/hisi_pmic_spmi.c new file +759 -0
@@ -0,0 +1,759 @@ +/* +* Device driver for regulators in HISI PMIC IC +* +* Copyright (c) 2013 Linaro Ltd. +* Copyright (c) 2011 Hisilicon. +* +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +*/ + +#include <linux/slab.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <linux/module.h> +#include <linux/err.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/platform_device.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/of_device.h> +#include <linux/of_gpio.h> +#include <linux/of_irq.h> +#include <linux/mfd/hisi_pmic.h> +#include <linux/irq.h> +#include <linux/spmi.h> +#ifndef NO_IRQ +#define NO_IRQ 0 +#endif + +/* 8-bit register offset in PMIC */ +#define HISI_MASK_STATE 0xff + +#define HISI_IRQ_KEY_NUM 0 +#define HISI_IRQ_KEY_VALUE 0xc0 +#define HISI_IRQ_KEY_DOWN 7 +#define HISI_IRQ_KEY_UP 6 + +/*#define HISI_NR_IRQ 25*/ +#define HISI_MASK_FIELD 0xFF +#define HISI_BITS 8 +#define PMIC_FPGA_FLAG 1 + +/*define the first group interrupt register number*/ +#define HISI_PMIC_FIRST_GROUP_INT_NUM 2 + +static struct bit_info g_pmic_vbus = {0 }; +#ifndef BIT +#define BIT (x) (0x1U << (x)) +#endif + +static struct hisi_pmic *g_pmic; +static unsigned int g_extinterrupt_flag =0 ; +static struct of_device_id of_hisi_pmic_match_tbl[] = { + { + .compatible ="hisilicon-hisi-pmic-spmi" , + }, + {/* end */ } +}; + +/* +* The PMIC register is only 8-bit. +* Hisilicon SoC use hardware to map PMIC register into SoC mapping. +* At here, we are accessing SoC register with 32-bit. +*/ +u32 hisi_pmic_read (struct hisi_pmic *pmic,int reg) +{ +u32 ret; +u8 read_value =0 ; +struct spmi_device *pdev; + +if (NULL == g_pmic) { +pr_err (" g_pmic is NULL\n" ); +return 0 ; + } + + pdev =to_spmi_device (g_pmic->dev); +if (NULL == pdev) { +pr_err ("%s:pdev get failed!\n" , __func__); +return 0 ; + } + + ret =spmi_ext_register_readl (pdev, reg, (unsigned char *)&read_value,1 );/*lint !e734 !e732 */ +if (ret) { +pr_err ("%s:spmi_ext_register_readl failed!\n" , __func__); +return ret; + } +return (u32 )read_value; +} +EXPORT_SYMBOL (hisi_pmic_read); + +void hisi_pmic_write (struct hisi_pmic *pmic,int reg,u32 val) +{ +u32 ret; +struct spmi_device *pdev; + +if (NULL == g_pmic) { +pr_err (" g_pmic is NULL\n" ); +return ; + } + + pdev =to_spmi_device (g_pmic->dev); +if (NULL == pdev) { +pr_err ("%s:pdev get failed!\n" , __func__); +return ; + } + + ret =spmi_ext_register_writel (pdev, reg, (unsigned char *)&val,1 );/*lint !e734 !e732 */ +if (ret) { +pr_err ("%s:spmi_ext_register_writel failed!\n" , __func__); +return ; + } +} +EXPORT_SYMBOL (hisi_pmic_write); + +#ifdef CONFIG_HISI_DIEID +u32 hisi_pmic_read_sub_pmu (u8 sid,int reg) +{ +u32 ret; +u8 read_value =0 ; +struct spmi_device *pdev; + +if (strstr (saved_command_line,"androidboot.swtype=factory" )) + { +if (NULL == g_pmic) { +pr_err (" g_pmic is NULL\n" ); +return -1 ;/*lint !e570 */ + } + + pdev =to_spmi_device (g_pmic->dev); +if (NULL == pdev) { +pr_err ("%s:pdev get failed!\n" , __func__); +return -1 ;/*lint !e570 */ + } + + ret =spmi_ext_register_readl (pdev->ctrl, sid, reg, (unsigned char *)&read_value,1 );/*lint !e734 !e732 */ +if (ret) { +pr_err ("%s:spmi_ext_register_readl failed!\n" , __func__); +return ret; + } +return (u32 )read_value; + } +return 0 ; +} +EXPORT_SYMBOL (hisi_pmic_read_sub_pmu); + +void hisi_pmic_write_sub_pmu (u8 sid,int reg,u32 val) +{ +u32 ret; +struct spmi_device *pdev; +if (strstr (saved_command_line,"androidboot.swtype=factory" )) + { +if (NULL == g_pmic) { +pr_err (" g_pmic is NULL\n" ); +return ; + } + + pdev =to_spmi_device (g_pmic->dev); +if (NULL == pdev) { +pr_err ("%s:pdev get failed!\n" , __func__); +return ; + } + + ret =spmi_ext_register_writel (pdev->ctrl, sid, reg, (unsigned char *)&val,1 );/*lint !e734 !e732 */ +if (ret) { +pr_err ("%s:spmi_ext_register_writel failed!\n" , __func__); +return ; + } + } + +return ; +} +EXPORT_SYMBOL (hisi_pmic_write_sub_pmu); +#endif + +void hisi_pmic_rmw (struct hisi_pmic *pmic,int reg, +u32 mask,u32 bits) +{ +u32 data; +unsigned long flags; + +if (NULL == g_pmic) { +pr_err (" g_pmic is NULL\n" ); +return ; + } + +spin_lock_irqsave (&g_pmic->lock, flags); + data =hisi_pmic_read (pmic, reg) & ~mask; + data |= mask & bits; +hisi_pmic_write (pmic, reg, data); +spin_unlock_irqrestore (&g_pmic->lock, flags); +} +EXPORT_SYMBOL (hisi_pmic_rmw); + +unsigned int hisi_pmic_reg_read (int addr) +{ +return (unsigned int )hisi_pmic_read (g_pmic, addr); +} +EXPORT_SYMBOL (hisi_pmic_reg_read); + +void hisi_pmic_reg_write (int addr,int val) +{ +hisi_pmic_write (g_pmic, addr, val); +} +EXPORT_SYMBOL (hisi_pmic_reg_write); + +void hisi_pmic_reg_write_lock (int addr,int val) +{ +unsigned long flags; + +if (NULL == g_pmic) { +pr_err (" g_pmic is NULL\n" ); +return ; + } + +spin_lock_irqsave (&g_pmic->lock, flags); +hisi_pmic_write (g_pmic, g_pmic->normal_lock.addr, g_pmic->normal_lock.val); +hisi_pmic_write (g_pmic, g_pmic->debug_lock.addr, g_pmic->debug_lock.val); +hisi_pmic_write (g_pmic, addr, val); +hisi_pmic_write (g_pmic, g_pmic->normal_lock.addr,0 ); +hisi_pmic_write (g_pmic, g_pmic->debug_lock.addr,0 ); +spin_unlock_irqrestore (&g_pmic->lock, flags); +} + +int hisi_pmic_array_read (int addr,char *buff,unsigned int len) +{ +unsigned int i; + +if ((len >32 ) || (NULL == buff)) { +return -EINVAL ; + } + +/* +* Here is a bug in the pmu die. +* the coul driver will read 4 bytes, +* but the ssi bus only read 1 byte, and the pmu die +* will make sampling 1/10669us about vol cur,so the driver +* read the data is not the same sampling +*/ +for (i =0 ; i < len; i++) + { + *(buff + i) =hisi_pmic_reg_read (addr+i); + } + +return 0 ; +} + +int hisi_pmic_array_write (int addr,char *buff,unsigned int len) +{ +unsigned int i; + +if ((len >32 ) || (NULL == buff)) { +return -EINVAL ; + } + +for (i =0 ; i < len; i++) + { +hisi_pmic_reg_write (addr+i, *(buff + i)); + } + +return 0 ; +} + +static irqreturn_t hisi_irq_handler (int irq,void *data) +{ +struct hisi_pmic *pmic = (struct hisi_pmic *)data; +unsigned long pending; +int i, offset; + +for (i =0 ; i < pmic->irqarray; i++) { + pending =hisi_pmic_reg_read ((i + pmic->irq_addr.start_addr)); + pending &=HISI_MASK_FIELD ; +if (pending !=0 ) { +pr_info ("pending[%d]=0x%lx\n\r" , i, pending); + } + +hisi_pmic_reg_write ((i + pmic->irq_addr.start_addr), pending); + +/*solve powerkey order*/ +if ((HISI_IRQ_KEY_NUM == i) && ((pending &HISI_IRQ_KEY_VALUE ) ==HISI_IRQ_KEY_VALUE )) { +generic_handle_irq (pmic->irqs[HISI_IRQ_KEY_DOWN ]); +generic_handle_irq (pmic->irqs[HISI_IRQ_KEY_UP ]); + pending &= (~HISI_IRQ_KEY_VALUE ); + } + +if (pending) { +for_each_set_bit (offset, &pending,HISI_BITS ) +generic_handle_irq (pmic->irqs[offset + i *HISI_BITS ]);/*lint !e679 */ + } + } + +/*Handle the second group irq if analysis the second group irq from dtsi*/ +if (1 == g_extinterrupt_flag){ +for (i =0 ; i < pmic->irqarray1; i++) { + pending =hisi_pmic_reg_read ((i + pmic->irq_addr1.start_addr)); + pending &=HISI_MASK_FIELD ; +if (pending !=0 ) { +pr_info ("pending[%d]=0x%lx\n\r" , i, pending); + } + +hisi_pmic_reg_write ((i + pmic->irq_addr1.start_addr), pending); + +if (pending) { +for_each_set_bit (offset, &pending,HISI_BITS ) +generic_handle_irq (pmic->irqs[offset + (i+HISI_PMIC_FIRST_GROUP_INT_NUM ) *HISI_BITS ]);/*lint !e679 */ + } + } + } + +return IRQ_HANDLED ; +} + +static void hisi_irq_mask (struct irq_data *d) +{ +struct hisi_pmic *pmic =irq_data_get_irq_chip_data (d); +u32 data, offset; +unsigned long flags; + +if (NULL == g_pmic) { +pr_err (" g_pmic is NULL\n" ); +return ; + } + + offset = (irqd_to_hwirq (d) >>3 ); +if (1 ==g_extinterrupt_flag){ +if ( offset <HISI_PMIC_FIRST_GROUP_INT_NUM ) + offset += pmic->irq_mask_addr.start_addr; +else /*Change addr when irq num larger than 16 because interrupt addr is nonsequence*/ + offset = offset+(pmic->irq_mask_addr1.start_addr)-HISI_PMIC_FIRST_GROUP_INT_NUM ; + }else { + offset += pmic->irq_mask_addr.start_addr; + } +spin_lock_irqsave (&g_pmic->lock, flags); + data =hisi_pmic_reg_read (offset); + data |= (1 << (irqd_to_hwirq (d) &0x07 )); +hisi_pmic_reg_write (offset, data); +spin_unlock_irqrestore (&g_pmic->lock, flags); +} + +static void hisi_irq_unmask (struct irq_data *d) +{ +struct hisi_pmic *pmic =irq_data_get_irq_chip_data (d); +u32 data, offset; +unsigned long flags; + +if (NULL == g_pmic) { +pr_err (" g_pmic is NULL\n" ); +return ; + } + + offset = (irqd_to_hwirq (d) >>3 ); +if (1 ==g_extinterrupt_flag){ +if ( offset <HISI_PMIC_FIRST_GROUP_INT_NUM ) + offset += pmic->irq_mask_addr.start_addr; +else + offset = offset+(pmic->irq_mask_addr1.start_addr)-HISI_PMIC_FIRST_GROUP_INT_NUM ; + }else { + offset += pmic->irq_mask_addr.start_addr; + } +spin_lock_irqsave (&g_pmic->lock, flags); + data =hisi_pmic_reg_read (offset); + data &= ~(1 << (irqd_to_hwirq (d) &0x07 ));/*lint !e502 */ +hisi_pmic_reg_write (offset, data); +spin_unlock_irqrestore (&g_pmic->lock, flags); +} + +static struct irq_chip hisi_pmu_irqchip = { + .name ="hisi-irq" , + .irq_mask = hisi_irq_mask, + .irq_unmask = hisi_irq_unmask, + .irq_disable = hisi_irq_mask, + .irq_enable = hisi_irq_unmask, +}; + +static int hisi_irq_map (struct irq_domain *d,unsigned int virq, +irq_hw_number_t hw) +{ +struct hisi_pmic *pmic = d->host_data; + +irq_set_chip_and_handler_name (virq, &hisi_pmu_irqchip, + handle_simple_irq,"hisi" ); +irq_set_chip_data (virq, pmic); +irq_set_irq_type (virq,IRQ_TYPE_NONE ); + +return 0 ; +} + +static struct irq_domain_ops hisi_domain_ops = { + .map = hisi_irq_map, + .xlate = irq_domain_xlate_twocell, +}; + +/*lint -e570 -e64*/ +static int get_pmic_device_tree_data (struct device_node *np,struct hisi_pmic *pmic) +{ +int ret =0 ; + +/*get pmic irq num*/ + ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-irq-num" , + &(pmic->irqnum),1 ); +if (ret) { +pr_err ("no hisilicon,hisi-pmic-irq-num property set\n" ); + ret = -ENODEV ; +return ret; + } + +/*get pmic irq array number*/ + ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-irq-array" , + &(pmic->irqarray),1 ); +if (ret) { +pr_err ("no hisilicon,hisi-pmic-irq-array property set\n" ); + ret = -ENODEV ; +return ret; + } + +/*SOC_PMIC_IRQ_MASK_0_ADDR*/ + ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-irq-mask-addr" , + (int *)&pmic->irq_mask_addr,2 ); +if (ret) { +pr_err ("no hisilicon,hisi-pmic-irq-mask-addr property set\n" ); + ret = -ENODEV ; +return ret; + } + +/*SOC_PMIC_IRQ0_ADDR*/ + ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-irq-addr" , + (int *)&pmic->irq_addr,2 ); +if (ret) { +pr_err ("no hisilicon,hisi-pmic-irq-addr property set\n" ); + ret = -ENODEV ; +return ret; + } + + ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-vbus" , + (u32 *)&g_pmic_vbus,2 ); +if (ret) { +pr_err ("no hisilicon,hisi-pmic-vbus property\n" ); + ret = -ENODEV ; +return ret; + } + +/*pmic lock*/ + ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-lock" , + (int *)&pmic->normal_lock,2 ); +if (ret) { +pr_err ("no hisilicon,hisi-pmic-lock property set\n" ); + ret = -ENODEV ; +return ret; + } + +/*pmic debug lock*/ + ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-debug-lock" , + (int *)&pmic->debug_lock,2 ); +if (ret) { +pr_err ("no hisilicon,hisi-pmic-debug-lock property set\n" ); + ret = -ENODEV ; +return ret; + } + +return ret; +}/*lint -restore*/ + + +/*lint -e570 -e64*/ +static int get_pmic_device_tree_data1 (struct device_node *np,struct hisi_pmic *pmic) +{ +int ret =0 ; + +/*get pmic irq num*/ + ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-irq-num1" , + &(pmic->irqnum1),1 ); +if (ret) { +pr_err ("no hisilicon,hisi-pmic-irq-num1 property set\n" ); + ret = -ENODEV ; + pmic->irqnum1 =0 ; +return ret; + } + +/*get pmic irq array number*/ + ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-irq-array1" , + &(pmic->irqarray1),1 ); +if (ret) { +pr_err ("no hisilicon,hisi-pmic-irq-array1 property set\n" ); + ret = -ENODEV ; +return ret; + } + +/*SOC_PMIC_IRQ_MASK_0_ADDR*/ + ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-irq-mask-addr1" , + (int *)&pmic->irq_mask_addr1,2 ); +if (ret) { +pr_err ("no hisilicon,hisi-pmic-irq-mask-addr1 property set\n" ); + ret = -ENODEV ; +return ret; + } + +/*SOC_PMIC_IRQ0_ADDR*/ + ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-irq-addr1" , + (int *)&pmic->irq_addr1,2 ); +if (ret) { +pr_err ("no hisilicon,hisi-pmic-irq-addr1 property set\n" ); + ret = -ENODEV ; +return ret; + } + + g_extinterrupt_flag =1 ; +return ret; +}/*lint -restore*/ + +int hisi_get_pmic_irq_byname (unsigned int pmic_irq_list) +{ +if (NULL == g_pmic ) { +pr_err ("[%s]g_pmic is NULL\n" , __func__); +return -1 ; + } + +if (pmic_irq_list > (unsigned int )g_pmic->irqnum) { +pr_err ("[%s]input pmic irq number is error.\n" , __func__); +return -1 ; + } +pr_info ("%s:g_pmic->irqs[%d]=%d\n" , __func__, pmic_irq_list, g_pmic->irqs[pmic_irq_list]); +return (int )g_pmic->irqs[pmic_irq_list]; +} +EXPORT_SYMBOL (hisi_get_pmic_irq_byname); + +int hisi_pmic_get_vbus_status (void ) +{ +if (0 == g_pmic_vbus.addr) +return -1 ; + +if (hisi_pmic_reg_read (g_pmic_vbus.addr) &BIT (g_pmic_vbus.bit)) +return 1 ; + +return 0 ; +} +EXPORT_SYMBOL (hisi_pmic_get_vbus_status); + +static void hisi_pmic_irq_prc (struct hisi_pmic *pmic) +{ +int i; +for (i =0 ; i < pmic->irq_mask_addr.array; i++) { +hisi_pmic_write (pmic, pmic->irq_mask_addr.start_addr + i,HISI_MASK_STATE ); + } + +for (i =0 ; i < pmic->irq_addr.array; i++) { +unsigned int pending =hisi_pmic_read (pmic, pmic->irq_addr.start_addr + i); +pr_debug ("PMU IRQ address value:irq[0x%x] = 0x%x\n" , pmic->irq_addr.start_addr + i, pending); +hisi_pmic_write (pmic, pmic->irq_addr.start_addr + i,HISI_MASK_STATE ); + } + +} + +static void hisi_pmic_irq1_prc (struct hisi_pmic *pmic) +{ +int i; +if (1 == g_extinterrupt_flag){ +for (i =0 ; i < pmic->irq_mask_addr1.array; i++) { +hisi_pmic_write (pmic, pmic->irq_mask_addr1.start_addr + i,HISI_MASK_STATE ); + } + +for (i =0 ; i < pmic->irq_addr1.array; i++) { +unsigned int pending1 =hisi_pmic_read (pmic, pmic->irq_addr1.start_addr + i); +pr_debug ("PMU IRQ address1 value:irq[0x%x] = 0x%x\n" , pmic->irq_addr1.start_addr + i, pending1); +hisi_pmic_write (pmic, pmic->irq_addr1.start_addr + i,HISI_MASK_STATE ); + } + } +} + +static int hisi_pmic_probe (struct spmi_device *pdev) +{ +struct device *dev = &pdev->dev; +struct device_node *np = dev->of_node; +struct hisi_pmic *pmic =NULL ; +enum of_gpio_flags flags; +int ret =0 ; +int i; +unsigned int fpga_flag =0 ; +unsigned int virq; + + pmic =devm_kzalloc (dev,sizeof (*pmic),GFP_KERNEL ); +if (!pmic) { +dev_err (dev,"cannot allocate hisi_pmic device info\n" ); +return -ENOMEM ; + } + +/*TODO: get pmic dts info*/ + ret =get_pmic_device_tree_data (np, pmic); +if (ret) { +dev_err (&pdev->dev,"Error reading hisi pmic dts \n" ); +return ret; + } + +/*get pmic dts the second group irq*/ + ret =get_pmic_device_tree_data1 (np, pmic); +if (ret) { +dev_err (&pdev->dev,"the platform don't support ext-interrupt.\n" ); + } + +/* TODO: get and enable clk request */ +spin_lock_init (&pmic->lock); + + pmic->dev = dev; + g_pmic = pmic; + ret =of_property_read_u32_array (np,"hisilicon,pmic_fpga_flag" , &fpga_flag,1 ); +if (ret) { +pr_err ("no hisilicon,pmic_fpga_flag property set\n" ); + } +if (PMIC_FPGA_FLAG == fpga_flag) { + goto after_irq_register; + } + + pmic->gpio =of_get_gpio_flags (np,0 , &flags); +if (pmic->gpio <0 ) +return pmic->gpio; + +if (!gpio_is_valid (pmic->gpio)) +return -EINVAL ; + + ret =gpio_request_one (pmic->gpio,GPIOF_IN ,"pmic" ); +if (ret <0 ) { +dev_err (dev,"failed to request gpio%d\n" , pmic->gpio); +return ret; + } + + pmic->irq =gpio_to_irq (pmic->gpio); + +/* mask && clear IRQ status */ +hisi_pmic_irq_prc (pmic); +/*clear && mask the new adding irq*/ +hisi_pmic_irq1_prc (pmic); + + pmic->irqnum += pmic->irqnum1; + + pmic->irqs = (unsigned int *)devm_kmalloc (dev, pmic->irqnum *sizeof (int ),GFP_KERNEL ); +if (!pmic->irqs) { +pr_err ("%s:Failed to alloc memory for pmic irq number!\n" , __func__); + goto irq_malloc; + } +memset (pmic->irqs,0 , pmic->irqnum); + + pmic->domain =irq_domain_add_simple (np, pmic->irqnum,0 , + &hisi_domain_ops, pmic); +if (!pmic->domain) { +dev_err (dev,"failed irq domain add simple!\n" ); + ret = -ENODEV ; + goto irq_domain; + } + +for (i =0 ; i < pmic->irqnum; i++) { + virq =irq_create_mapping (pmic->domain, i); +if (virq ==NO_IRQ ) { +pr_debug ("Failed mapping hwirq\n" ); + ret = -ENOSPC ; + goto irq_create_mapping; + } + pmic->irqs[i] = virq; +pr_info ("[%s]. pmic->irqs[%d] = %d\n" , __func__, i, pmic->irqs[i]); + } + + ret =request_threaded_irq (pmic->irq, hisi_irq_handler,NULL , +IRQF_TRIGGER_LOW |IRQF_SHARED |IRQF_NO_SUSPEND , +"pmic" , pmic); +if (ret <0 ) { +dev_err (dev,"could not claim pmic %d\n" , ret); + ret = -ENODEV ; + goto request_theaded_irq; + } + +after_irq_register: +return 0 ; + + +request_theaded_irq: +irq_create_mapping: +irq_domain: +irq_malloc: +gpio_free (pmic->gpio); + g_pmic =NULL ; +return ret; +} + +static void hisi_pmic_remove (struct spmi_device *pdev) +{ + +struct hisi_pmic *pmic =dev_get_drvdata (&pdev->dev); + +free_irq (pmic->irq, pmic); +gpio_free (pmic->gpio); +devm_kfree (&pdev->dev, pmic); + +} +static int hisi_pmic_suspend (struct device *dev,pm_message_t state) +{ +struct hisi_pmic *pmic =dev_get_drvdata (dev); + +if (NULL == pmic) { +pr_err ("%s:pmic is NULL\n" , __func__); +return -ENOMEM ; + } + +pr_info ("%s:+\n" , __func__); +pr_info ("%s:-\n" , __func__); + +return 0 ; +}/*lint !e715 */ + +static int hisi_pmic_resume (struct device *dev) +{ +struct hisi_pmic *pmic =dev_get_drvdata (dev); + +if (NULL == pmic) { +pr_err ("%s:pmic is NULL\n" , __func__); +return -ENOMEM ; + } + +pr_info ("%s:+\n" , __func__); +pr_info ("%s:-\n" , __func__); + +return 0 ; +} + +MODULE_DEVICE_TABLE (spmi, pmic_spmi_id); +static struct spmi_driver hisi_pmic_driver = { + .driver = { + .name ="hisi_pmic" , + .owner =THIS_MODULE , + .of_match_table = of_hisi_pmic_match_tbl, + .suspend = hisi_pmic_suspend, + .resume = hisi_pmic_resume, + }, + .probe = hisi_pmic_probe, + .remove = hisi_pmic_remove, +}; + +static int __init hisi_pmic_init (void ) +{ +return spmi_driver_register (&hisi_pmic_driver); +} + +static void __exit hisi_pmic_exit(void) +{ +spmi_driver_unregister (&hisi_pmic_driver); +} + + +subsys_initcall_sync (hisi_pmic_init); +module_exit (hisi_pmic_exit); + +MODULE_DESCRIPTION ("PMIC driver" ); +MODULE_LICENSE ("GPL v2" ); +
drivers/regulator/hisi_regulator_spmi.c new file +741 -0
741 lines not on this page · raw message
drivers/spmi/hisi-spmi-controller.c new file +390 -0
390 lines not on this page · raw message
include/linux/mfd/hisi_pmic.h new file +165 -0
165 lines not on this page · raw message
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 28/33 regulator: hi6421v600-regulator: initialize ramp_delay
In reply to Mauro Carvalho ChehabWithout that, the regulator's core complains with:
ldo17: ramp_delay not set
For now, use the enable time, as we don't have any datasheets from this device.
--- drivers/regulator/hi6421v600-regulator.c | 3 +++ 1 file changed, 3 insertions(+)
drivers/regulator/hi6421v600-regulator.c +3 -0
@@ -267,6 +267,9 @@ static int hi6421_spmi_dt_parse(struct platform_device *pdev,return ret; } +/* FIXME: are there a better value for this? */ + rdesc->ramp_delay = rdesc->enable_time; +/* parse .eco_uA */ ret =of_property_read_u32 (np,"eco-microamp" , &sreg->eco_uA);
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 20/33 regulator: hi6421v600-regulator: cleanup struct hisi_regulator
In reply to Mauro Carvalho ChehabThere are several fields on this struct that can be removed, as they already exists at struct regulator_desc.
Remove them, cleaning up the code in the process.
While here, rename it to hi6421v600_regulator_info, in order to better match the driver's name.
--- drivers/regulator/hi6421v600-regulator.c | 226 +++++++++-------------- 1 file changed, 92 insertions(+), 134 deletions(-)
drivers/regulator/hi6421v600-regulator.c +92 -134
@@ -39,21 +39,11 @@#include <linux/uaccess.h> #include <linux/spmi.h> -struct hisi_regulator_register_info { -u32 ctrl_reg; -u32 enable_mask; -u32 eco_mode_mask; -u32 vset_reg; -u32 vset_mask; -}; - -struct hisi_regulator { -const char *name; -struct hisi_regulator_register_info register_info; -u32 off_on_delay; -u32 eco_uA; +struct hi6421v600_regulator {struct regulator_desc rdesc;struct hisi_pmic *pmic; +u8 eco_mode_mask; +u32 eco_uA; };static DEFINE_MUTEX (enable_mutex);
@@ -62,29 +52,29 @@ static DEFINE_MUTEX(enable_mutex);* microseconds after 'since'. */ -static int hisi_regulator_is_enabled (struct regulator_dev *dev) +static int hisi_regulator_is_enabled (struct regulator_dev *rdev) {u32 reg_val; -struct hisi_regulator *sreg =rdev_get_drvdata (dev); +struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev);struct hisi_pmic *pmic = sreg->pmic; - reg_val =hisi_pmic_read (pmic, sreg->register_info.ctrl_reg); -pr_debug ("<[%s]: ctrl_reg=0x%x,enable_state=%d>\n" , - __func__, sreg->register_info.ctrl_reg, - (reg_val & sreg->register_info.enable_mask)); + reg_val =hisi_pmic_read (pmic, rdev->desc->enable_reg); +pr_debug ("<[%s]: enable_reg=0x%x,enable_state=%d>\n" , + __func__, rdev->desc->enable_reg, + (reg_val & rdev->desc->enable_mask)); -return ((reg_val & sreg->register_info.enable_mask) !=0 ); +return ((reg_val & rdev->desc->enable_mask) !=0 ); } -static int hisi_regulator_enable (struct regulator_dev *dev) +static int hisi_regulator_enable (struct regulator_dev *rdev) { -struct hisi_regulator *sreg =rdev_get_drvdata (dev); +struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev);struct hisi_pmic *pmic = sreg->pmic;/* keep a distance of off_on_delay from last time disabled */ -usleep_range (sreg->off_on_delay, sreg->off_on_delay +1000 ); +usleep_range (rdev->desc->off_on_delay, rdev->desc->off_on_delay +1000 ); -pr_debug ("<[%s]: off_on_delay=%dus>\n" , __func__, sreg->off_on_delay); +pr_debug ("<[%s]: off_on_delay=%dus>\n" , __func__, rdev->desc->off_on_delay);/* cannot enable more than one regulator at one time */ mutex_lock (&enable_mutex);
@@ -92,103 +82,103 @@ static int hisi_regulator_enable(struct regulator_dev *dev) HISI_REGS_ENA_PROTECT_TIME + 1000);/* set enable register */ -hisi_pmic_rmw (pmic, sreg->register_info.ctrl_reg, - sreg->register_info.enable_mask, - sreg->register_info.enable_mask); -pr_debug ("<[%s]: ctrl_reg=0x%x,enable_mask=0x%x>\n" , - __func__, sreg->register_info.ctrl_reg, - sreg->register_info.enable_mask); +hisi_pmic_rmw (pmic, rdev->desc->enable_reg, + rdev->desc->enable_mask, + rdev->desc->enable_mask); +pr_debug ("<[%s]: enable_reg=0x%x,enable_mask=0x%x>\n" , + __func__, rdev->desc->enable_reg, + rdev->desc->enable_mask);mutex_unlock (&enable_mutex);return 0 ; } -static int hisi_regulator_disable (struct regulator_dev *dev) +static int hisi_regulator_disable (struct regulator_dev *rdev) { -struct hisi_regulator *sreg =rdev_get_drvdata (dev); +struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev);struct hisi_pmic *pmic = sreg->pmic;/* set enable register to 0 */ -hisi_pmic_rmw (pmic, sreg->register_info.ctrl_reg, - sreg->register_info.enable_mask,0 ); +hisi_pmic_rmw (pmic, rdev->desc->enable_reg, + rdev->desc->enable_mask,0 );return 0 ; } -static int hisi_regulator_get_voltage (struct regulator_dev *dev) +static int hisi_regulator_get_voltage (struct regulator_dev *rdev) { -struct hisi_regulator *sreg =rdev_get_drvdata (dev); +struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev);struct hisi_pmic *pmic = sreg->pmic;u32 reg_val, selector;/* get voltage selector */ - reg_val =hisi_pmic_read (pmic, sreg->register_info.vset_reg); -pr_debug ("<[%s]: vset_reg=0x%x>\n" , - __func__, sreg->register_info.vset_reg); + reg_val =hisi_pmic_read (pmic, rdev->desc->vsel_reg); +pr_debug ("<[%s]: vsel_reg=0x%x>\n" , + __func__, rdev->desc->vsel_reg); - selector = (reg_val & sreg->register_info.vset_mask) >> - (ffs (sreg->register_info.vset_mask) -1 ); + selector = (reg_val & rdev->desc->vsel_mask) >> + (ffs (rdev->desc->vsel_mask) -1 ); -return sreg->rdesc.ops->list_voltage (dev, selector); +return rdev->desc->ops->list_voltage (rdev, selector); } -static int hisi_regulator_set_voltage (struct regulator_dev *dev, +static int hisi_regulator_set_voltage (struct regulator_dev *rdev,int min_uV,int max_uV,unsigned int *selector) { -struct hisi_regulator *sreg =rdev_get_drvdata (dev); +struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev);struct hisi_pmic *pmic = sreg->pmic;u32 vsel;int ret =0 ; -for (vsel =0 ; vsel < sreg->rdesc.n_voltages; vsel++) { -int uV = sreg->rdesc.volt_table[vsel]; +for (vsel =0 ; vsel < rdev->desc->n_voltages; vsel++) { +int uV = rdev->desc->volt_table[vsel];/* Break at the first in-range value */ if (min_uV <= uV && uV <= max_uV)break ; }/* unlikely to happen. sanity test done by regulator core */ -if (unlikely (vsel == sreg->rdesc.n_voltages)) +if (unlikely (vsel == rdev->desc->n_voltages))return -EINVAL ; *selector = vsel;/* set voltage selector */ -hisi_pmic_rmw (pmic, sreg->register_info.vset_reg, - sreg->register_info.vset_mask, - vsel << (ffs (sreg->register_info.vset_mask) -1 )); +hisi_pmic_rmw (pmic, rdev->desc->vsel_reg, + rdev->desc->vsel_mask, + vsel << (ffs (rdev->desc->vsel_mask) -1 )); -pr_debug ("<[%s]: vset_reg=0x%x, vset_mask=0x%x, value=0x%x>\n" , +pr_debug ("<[%s]: vsel_reg=0x%x, vsel_mask=0x%x, value=0x%x>\n" , __func__, - sreg->register_info.vset_reg, - sreg->register_info.vset_mask, - vsel << (ffs (sreg->register_info.vset_mask) -1 )); + rdev->desc->vsel_reg, + rdev->desc->vsel_mask, + vsel << (ffs (rdev->desc->vsel_mask) -1 ));return ret; } -static unsigned int hisi_regulator_get_mode (struct regulator_dev *dev) +static unsigned int hisi_regulator_get_mode (struct regulator_dev *rdev) { -struct hisi_regulator *sreg =rdev_get_drvdata (dev); +struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev);struct hisi_pmic *pmic = sreg->pmic;u32 reg_val; - reg_val =hisi_pmic_read (pmic, sreg->register_info.ctrl_reg); -pr_debug ("<[%s]: reg_val=%d, ctrl_reg=0x%x, eco_mode_mask=0x%x>\n" , + reg_val =hisi_pmic_read (pmic, rdev->desc->enable_reg); +pr_debug ("<[%s]: reg_val=%d, enable_reg=0x%x, eco_mode_mask=0x%x>\n" , __func__, reg_val, - sreg->register_info.ctrl_reg, - sreg->register_info.eco_mode_mask); + rdev->desc->enable_reg, + sreg->eco_mode_mask); -if (reg_val & sreg->register_info.eco_mode_mask) +if (reg_val & sreg->eco_mode_mask)return REGULATOR_MODE_IDLE ;else return REGULATOR_MODE_NORMAL ; } -static int hisi_regulator_set_mode (struct regulator_dev *dev, +static int hisi_regulator_set_mode (struct regulator_dev *rdev,unsigned int mode) { -struct hisi_regulator *sreg =rdev_get_drvdata (dev); +struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev);struct hisi_pmic *pmic = sreg->pmic;u32 eco_mode;
@@ -204,23 +194,23 @@ static int hisi_regulator_set_mode(struct regulator_dev *dev, }/* set mode */ -hisi_pmic_rmw (pmic, sreg->register_info.ctrl_reg, - sreg->register_info.eco_mode_mask, - eco_mode << (ffs (sreg->register_info.eco_mode_mask) -1 )); +hisi_pmic_rmw (pmic, rdev->desc->enable_reg, + sreg->eco_mode_mask, + eco_mode << (ffs (sreg->eco_mode_mask) -1 )); -pr_debug ("<[%s]: ctrl_reg=0x%x, eco_mode_mask=0x%x, value=0x%x>\n" , +pr_debug ("<[%s]: enable_reg=0x%x, eco_mode_mask=0x%x, value=0x%x>\n" , __func__, - sreg->register_info.ctrl_reg, - sreg->register_info.eco_mode_mask, - eco_mode << (ffs (sreg->register_info.eco_mode_mask) -1 )); + rdev->desc->enable_reg, + sreg->eco_mode_mask, + eco_mode << (ffs (sreg->eco_mode_mask) -1 ));return 0 ; } -static unsigned int hisi_regulator_get_optimum_mode (struct regulator_dev *dev, +static unsigned int hisi_regulator_get_optimum_mode (struct regulator_dev *rdev,int input_uV,int output_uV,int load_uA) { -struct hisi_regulator *sreg =rdev_get_drvdata (dev); +struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev);if (load_uA || ((unsigned int )load_uA > sreg->eco_uA))return REGULATOR_MODE_NORMAL ;
@@ -228,42 +218,43 @@ static unsigned int hisi_regulator_get_optimum_mode(struct regulator_dev *dev,return REGULATOR_MODE_IDLE ; } -static int hisi_dt_parse_common (struct hisi_regulator *sreg, -struct platform_device *pdev) +static int hisi_dt_parse (struct platform_device *pdev, +struct hi6421v600_regulator *sreg, +struct regulator_desc *rdesc) {struct device *dev = &pdev->dev;struct device_node *np = dev->of_node; -struct regulator_desc *rdesc = &sreg->rdesc;unsigned int register_info[3 ] = {0 }; -int ret =0 ; +unsigned int *v_table; +int ret; -/* parse .register_info.ctrl_reg */ +/* parse .register_info.enable_reg */ ret =of_property_read_u32_array (np,"hisilicon,hisi-ctrl" , register_info,3 );if (ret) {dev_err (dev,"no hisilicon,hisi-ctrl property set\n" ); - goto dt_parse_common_end; +return ret; } - sreg->register_info.ctrl_reg = register_info[0 ]; - sreg->register_info.enable_mask = register_info[1 ]; - sreg->register_info.eco_mode_mask = register_info[2 ]; + rdesc->enable_reg = register_info[0 ]; + rdesc->enable_mask = register_info[1 ]; + sreg->eco_mode_mask = register_info[2 ]; -/* parse .register_info.vset_reg */ +/* parse .register_info.vsel_reg */ ret =of_property_read_u32_array (np,"hisilicon,hisi-vset" , register_info,2 );if (ret) {dev_err (dev,"no hisilicon,hisi-vset property set\n" ); - goto dt_parse_common_end; +return ret; } - sreg->register_info.vset_reg = register_info[0 ]; - sreg->register_info.vset_mask = register_info[1 ]; + rdesc->vsel_reg = register_info[0 ]; + rdesc->vsel_mask = register_info[1 ];/* parse .off-on-delay */ ret =of_property_read_u32 (np,"hisilicon,hisi-off-on-delay-us" , - &sreg->off_on_delay); + &rdesc->off_on_delay);if (ret) {dev_err (dev,"no hisilicon,hisi-off-on-delay-us property set\n" ); - goto dt_parse_common_end; +return ret; }/* parse .enable_time */
@@ -271,7 +262,7 @@ static int hisi_dt_parse_common(struct hisi_regulator *sreg, &rdesc->enable_time);if (ret) {dev_err (dev,"no hisilicon,hisi-enable-time-us property set\n" ); - goto dt_parse_common_end; +return ret; }/* parse .eco_uA */
@@ -282,56 +273,24 @@ static int hisi_dt_parse_common(struct hisi_regulator *sreg, ret =0 ; } -dt_parse_common_end: -return ret; -} +/* parse volt_table */ -static int hisi_dt_parse_ldo (struct hisi_regulator *sreg, -struct platform_device *pdev) -{ -struct device *dev = &pdev->dev; -struct device_node *np = dev->of_node; -struct regulator_desc *rdesc = &sreg->rdesc; -unsigned int *v_table; -int ret =0 ; + rdesc->n_voltages =of_property_count_u32_elems (np,"hisilicon,hisi-vset-table" ); -/* parse .n_voltages, and .volt_table */ - ret =of_property_read_u32 (np,"hisilicon,hisi-n-voltages" , - &rdesc->n_voltages); -if (ret) { -dev_err (dev,"no hisilicon,hisi-n-voltages property set\n" ); - goto dt_parse_ldo_end; - } - -/* alloc space for .volt_table */ v_table =devm_kzalloc (dev,sizeof (unsigned int ) * rdesc->n_voltages,GFP_KERNEL ); -if (unlikely (!v_table)) { - ret = -ENOMEM ; -dev_err (dev,"no memory for .volt_table\n" ); - goto dt_parse_ldo_end; - } +if (unlikely (!v_table)) +return -ENOMEM ; + rdesc->volt_table = v_table; ret =of_property_read_u32_array (np,"hisilicon,hisi-vset-table" , v_table, rdesc->n_voltages);if (ret) {dev_err (dev,"no hisilicon,hisi-vset-table property set\n" ); - goto dt_parse_ldo_end1; +return ret; } - rdesc->volt_table = v_table; -/* parse hisi regulator's dt common part */ - ret =hisi_dt_parse_common (sreg, pdev); -if (ret) { -dev_err (dev,"failure in hisi_dt_parse_common\n" ); - goto dt_parse_ldo_end1; - } - -return ret; - -dt_parse_ldo_end1: -dt_parse_ldo_end: -return ret; +return 0 ; }static struct regulator_ops hisi_ldo_rops = {
@@ -364,7 +323,7 @@ static int hisi_regulator_probe_ldo(struct platform_device *pdev,struct device *dev = &pdev->dev;struct regulator_desc *rdesc;struct regulator_dev *rdev; -struct hisi_regulator *sreg =NULL ; +struct hi6421v600_regulator *sreg =NULL ;struct regulator_init_data *initdata;struct regulator_config config = { };struct regulation_constraints *constraint;
@@ -401,11 +360,10 @@ static int hisi_regulator_probe_ldo(struct platform_device *pdev,if (!sreg)return -ENOMEM ; - sreg->name = initdata->constraints.name; sreg->pmic = pmic; rdesc = &sreg->rdesc; - rdesc->name = sreg->name; + rdesc->name = initdata->constraints.name; rdesc->ops = &hisi_ldo_rops; rdesc->type =REGULATOR_VOLTAGE ; rdesc->min_uV = initdata->constraints.min_uV;
@@ -415,7 +373,7 @@ static int hisi_regulator_probe_ldo(struct platform_device *pdev, initdata->supply_regulator = supplyname;/* parse device tree data for regulator specific */ - ret =hisi_dt_parse_ldo (sreg, pdev); + ret =hisi_dt_parse (pdev, sreg, rdesc);if (ret) {dev_err (dev,"device tree parameter parse error!\n" ); goto hisi_probe_end;
@@ -501,13 +459,13 @@ static int hisi_regulator_probe(struct platform_device *pdev)static int hisi_regulator_remove (struct platform_device *pdev) {struct regulator_dev *rdev =dev_get_drvdata (&pdev->dev); -struct hisi_regulator *sreg =rdev_get_drvdata (rdev); +struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev);regulator_unregister (rdev);/* TODO: should i worry about that? devm_kzalloc */ -if (sreg->rdesc.volt_table) -devm_kfree (&pdev->dev, (unsigned int *)sreg->rdesc.volt_table); +if (rdev->desc->volt_table) +devm_kfree (&pdev->dev, (unsigned int *)rdev->desc->volt_table);kfree (sreg);
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 26/33 regulator: hi6421v600-regulator: don't use usleep_range for off_on_delay
In reply to Mauro Carvalho ChehabThe regulator's core already handles it.
--- drivers/regulator/hi6421v600-regulator.c | 3 --- 1 file changed, 3 deletions(-)
drivers/regulator/hi6421v600-regulator.c +0 -3
@@ -73,9 +73,6 @@ static int hi6421_spmi_regulator_enable(struct regulator_dev *rdev)struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev);struct hi6421_spmi_pmic *pmic = sreg->pmic; -/* keep a distance of off_on_delay from last time disabled */ -usleep_range (rdev->desc->off_on_delay, rdev->desc->off_on_delay +1000 ); -dev_dbg (&rdev->dev,"%s: off_on_delay=%d us\n" , __func__, rdev->desc->off_on_delay);
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 22/33 regulator: hi6421v600-regulator: use shorter names for OF properties
In reply to Mauro Carvalho ChehabSimplify the names of the OF properties, in order to make them similar to other drivers and to make easier to understand what each property means.
--- drivers/regulator/hi6421v600-regulator.c | 52 ++++++++++-------------- 1 file changed, 21 insertions(+), 31 deletions(-)
drivers/regulator/hi6421v600-regulator.c +21 -31
@@ -196,14 +196,14 @@ static int hisi_regulator_set_mode(struct regulator_dev *rdev, {struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev);struct hisi_pmic *pmic = sreg->pmic; -u32 eco_mode; +u32 val;switch (mode) {case REGULATOR_MODE_NORMAL : - eco_mode =HISI_ECO_MODE_DISABLE ; + val =0 ;break ;case REGULATOR_MODE_IDLE : - eco_mode =HISI_ECO_MODE_ENABLE ; + val = sreg->eco_mode_mask << (ffs (sreg->eco_mode_mask) -1 );break ;default :return -EINVAL ;
@@ -211,15 +211,12 @@ static int hisi_regulator_set_mode(struct regulator_dev *rdev,/* set mode */ hisi_pmic_rmw (pmic, rdev->desc->enable_reg, - sreg->eco_mode_mask, - eco_mode << (ffs (sreg->eco_mode_mask) -1 )); + sreg->eco_mode_mask, val);dev_dbg (&rdev->dev,"%s: enable_reg=0x%x, eco_mode_mask=0x%x, value=0x%x\n" , - __func__, - rdev->desc->enable_reg, - sreg->eco_mode_mask, - eco_mode << (ffs (sreg->eco_mode_mask) -1 )); + __func__, rdev->desc->enable_reg, sreg->eco_mode_mask, val); +return 0 ; }
@@ -249,10 +246,10 @@ static int hisi_dt_parse(struct platform_device *pdev,int ret;/* parse .register_info.enable_reg */ - ret =of_property_read_u32_array (np,"hisilicon,hisi-ctrl" , + ret =of_property_read_u32_array (np,"hi6421-ctrl" , register_info,3 );if (ret) { -dev_err (dev,"no hisilicon,hisi-ctrl property set\n" ); +dev_err (dev,"no hi6421-ctrl property set\n" );return ret; } rdesc->enable_reg = register_info[0 ];
@@ -260,33 +257,33 @@ static int hisi_dt_parse(struct platform_device *pdev, sreg->eco_mode_mask = register_info[2 ];/* parse .register_info.vsel_reg */ - ret =of_property_read_u32_array (np,"hisilicon,hisi-vset" , + ret =of_property_read_u32_array (np,"hi6421-vsel" , register_info,2 );if (ret) { -dev_err (dev,"no hisilicon,hisi-vset property set\n" ); +dev_err (dev,"no hi6421-vsel property set\n" );return ret; } rdesc->vsel_reg = register_info[0 ]; rdesc->vsel_mask = register_info[1 ];/* parse .off-on-delay */ - ret =of_property_read_u32 (np,"hisilicon,hisi-off-on-delay-us" , + ret =of_property_read_u32 (np,"off-on-delay-us" , &rdesc->off_on_delay);if (ret) { -dev_err (dev,"no hisilicon,hisi-off-on-delay-us property set\n" ); +dev_err (dev,"no off-on-delay-us property set\n" );return ret; }/* parse .enable_time */ - ret =of_property_read_u32 (np,"hisilicon,hisi-enable-time-us" , + ret =of_property_read_u32 (np,"startup-delay-us" , &rdesc->enable_time);if (ret) { -dev_err (dev,"no hisilicon,hisi-enable-time-us property set\n" ); +dev_err (dev,"no startup-delay-us property set\n" );return ret; }/* parse .eco_uA */ - ret =of_property_read_u32 (np,"hisilicon,hisi-eco-microamp" , + ret =of_property_read_u32 (np,"eco-microamp" , &sreg->eco_uA);if (ret) { sreg->eco_uA =0 ;
@@ -295,7 +292,7 @@ static int hisi_dt_parse(struct platform_device *pdev,/* parse volt_table */ - rdesc->n_voltages =of_property_count_u32_elems (np,"hisilicon,hisi-vset-table" ); + rdesc->n_voltages =of_property_count_u32_elems (np,"voltage-table" ); v_table =devm_kzalloc (dev,sizeof (unsigned int ) * rdesc->n_voltages,GFP_KERNEL );
@@ -303,10 +300,10 @@ static int hisi_dt_parse(struct platform_device *pdev,return -ENOMEM ; rdesc->volt_table = v_table; - ret =of_property_read_u32_array (np,"hisilicon,hisi-vset-table" , + ret =of_property_read_u32_array (np,"voltage-table" , v_table, rdesc->n_voltages);if (ret) { -dev_err (dev,"no hisilicon,hisi-vset-table property set\n" ); +dev_err (dev,"no voltage-table property set\n" );return ret; }
@@ -329,13 +326,6 @@ static struct regulator_ops hisi_ldo_rops = {* Used only for parsing the DT properties */ -static const struct of_device_id of_hisi_pmic_match_tbl[] = { - { - .compatible ="hisilicon,hi6421-spmi-pmic-ldo" , - }, - { } -}; -static int hisi_regulator_probe_ldo (struct platform_device *pdev,struct device_node *np,struct hisi_pmic *pmic)
@@ -360,14 +350,14 @@ static int hisi_regulator_probe_ldo(struct platform_device *pdev,/* hisi regulator supports two modes */ constraint = &initdata->constraints; - ret =of_property_read_u32_array (np,"hisilicon,valid-modes-mask" , + ret =of_property_read_u32_array (np,"valid-modes-mask" , &constraint->valid_modes_mask,1 );if (ret) {dev_err (dev,"no valid modes mask\n" ); ret = -ENODEV ;return ret; } - ret =of_property_read_u32_array (np,"hisilicon,valid-idle-mask" , + ret =of_property_read_u32_array (np,"valid-idle-mask" , &temp_modes,1 );if (ret) {dev_err (dev,"no valid idle mask\n" );
@@ -388,7 +378,7 @@ static int hisi_regulator_probe_ldo(struct platform_device *pdev, rdesc->type =REGULATOR_VOLTAGE ; rdesc->min_uV = initdata->constraints.min_uV; - supplyname =of_get_property (np,"hisilicon,supply_name" ,NULL ); + supplyname =of_get_property (np,"supply_name" ,NULL );if (supplyname) initdata->supply_regulator = supplyname;
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 18/33 mfd: hi6421-spmi-pmic: get rid of unused OF properties
In reply to Mauro Carvalho ChehabThere are several OF properties that aren't used by Hikey 970, and some are not even used inside the driver.
So, drop them, as as this makes easier to document what's actually used.
If latter needed, those could be re-added later.
--- drivers/mfd/hi6421-spmi-pmic.c | 145 +-------------------------- include/linux/mfd/hi6421-spmi-pmic.h | 14 +-- 2 files changed, 7 insertions(+), 152 deletions(-)
drivers/mfd/hi6421-spmi-pmic.c +4 -141
@@ -49,7 +49,6 @@/*#define HISI_NR_IRQ 25*/ #define HISI_MASK_FIELD 0xFF#define HISI_BITS 8 -#define PMIC_FPGA_FLAG 1/*define the first group interrupt register number*/ #define HISI_PMIC_FIRST_GROUP_INT_NUM 2
@@ -144,24 +143,6 @@ static irqreturn_t hisi_irq_handler(int irq, void *data) } } -/*Handle the second group irq if analysis the second group irq from dtsi*/ -if (pmic->g_extinterrupt_flag ==1 ) { -for (i =0 ; i < pmic->irqarray1; i++) { - pending =hisi_pmic_read (pmic, (i + pmic->irq_addr1.start_addr)); - pending &=HISI_MASK_FIELD ; -if (pending !=0 ) -pr_debug ("pending[%d]=0x%lx\n\r" , i, pending); - -hisi_pmic_write (pmic, (i + pmic->irq_addr1.start_addr), pending); - -if (!pending) -continue ; - -for_each_set_bit (offset, &pending,HISI_BITS ) -generic_handle_irq (pmic->irqs[offset + (i +HISI_PMIC_FIRST_GROUP_INT_NUM ) *HISI_BITS ]); - } - } -return IRQ_HANDLED ; }
@@ -172,19 +153,8 @@ static void hisi_irq_mask(struct irq_data *d)unsigned long flags; offset = (irqd_to_hwirq (d) >>3 ); -if (pmic->g_extinterrupt_flag ==1 ) { -if (offset <HISI_PMIC_FIRST_GROUP_INT_NUM ) { - offset += pmic->irq_mask_addr.start_addr; - }else { -/* -* Change addr when irq num larger than 16 because -* interrupt addr is nonsequence -*/ - offset = offset + (pmic->irq_mask_addr1.start_addr) -HISI_PMIC_FIRST_GROUP_INT_NUM ; - } - }else { - offset += pmic->irq_mask_addr.start_addr; - } + offset += pmic->irq_mask_addr.start_addr; +spin_lock_irqsave (&pmic->lock, flags); data =hisi_pmic_read (pmic, offset); data |= (1 << (irqd_to_hwirq (d) &0x07 ));
@@ -199,14 +169,8 @@ static void hisi_irq_unmask(struct irq_data *d)unsigned long flags; offset = (irqd_to_hwirq (d) >>3 ); -if (pmic->g_extinterrupt_flag ==1 ) { -if (offset <HISI_PMIC_FIRST_GROUP_INT_NUM ) - offset += pmic->irq_mask_addr.start_addr; -else - offset = offset + (pmic->irq_mask_addr1.start_addr) -HISI_PMIC_FIRST_GROUP_INT_NUM ; - }else { - offset += pmic->irq_mask_addr.start_addr; - } + offset += pmic->irq_mask_addr.start_addr; +spin_lock_irqsave (&pmic->lock, flags); data =hisi_pmic_read (pmic, offset); data &= ~(1 << (irqd_to_hwirq (d) &0x07 ));
@@ -280,69 +244,6 @@ static int get_pmic_device_tree_data(struct device_node *np, struct hisi_pmic *preturn ret; } -/*pmic lock*/ - ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-lock" , - (int *)&pmic->normal_lock,2 ); -if (ret) { -pr_err ("no hisilicon,hisi-pmic-lock property set\n" ); - ret = -ENODEV ; -return ret; - } - -/*pmic debug lock*/ - ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-debug-lock" , - (int *)&pmic->debug_lock,2 ); -if (ret) { -pr_err ("no hisilicon,hisi-pmic-debug-lock property set\n" ); - ret = -ENODEV ; -return ret; - } - -return ret; -} - -static int get_pmic_device_tree_data1 (struct device_node *np,struct hisi_pmic *pmic) -{ -int ret =0 ; - -/*get pmic irq num*/ - ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-irq-num1" , - &pmic->irqnum1,1 ); -if (ret) { -pr_err ("no hisilicon,hisi-pmic-irq-num1 property set\n" ); - ret = -ENODEV ; - pmic->irqnum1 =0 ; -return ret; - } - -/*get pmic irq array number*/ - ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-irq-array1" , - &pmic->irqarray1,1 ); -if (ret) { -pr_err ("no hisilicon,hisi-pmic-irq-array1 property set\n" ); - ret = -ENODEV ; -return ret; - } - -/*SOC_PMIC_IRQ_MASK_0_ADDR*/ - ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-irq-mask-addr1" , - (int *)&pmic->irq_mask_addr1,2 ); -if (ret) { -pr_err ("no hisilicon,hisi-pmic-irq-mask-addr1 property set\n" ); - ret = -ENODEV ; -return ret; - } - -/*SOC_PMIC_IRQ0_ADDR*/ - ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-irq-addr1" , - (int *)&pmic->irq_addr1,2 ); -if (ret) { -pr_err ("no hisilicon,hisi-pmic-irq-addr1 property set\n" ); - ret = -ENODEV ; -return ret; - } - - pmic->g_extinterrupt_flag =1 ;return ret; }
@@ -362,26 +263,6 @@ static void hisi_pmic_irq_prc(struct hisi_pmic *pmic) } } -static void hisi_pmic_irq1_prc (struct hisi_pmic *pmic) -{ -int i; -unsigned int pending1; - -if (pmic->g_extinterrupt_flag ==1 ) { -for (i =0 ; i < pmic->irq_mask_addr1.array; i++) -hisi_pmic_write (pmic, pmic->irq_mask_addr1.start_addr + i,HISI_MASK_STATE ); - -for (i =0 ; i < pmic->irq_addr1.array; i++) { - pending1 =hisi_pmic_read (pmic, pmic->irq_addr1.start_addr + i); - -pr_debug ("PMU IRQ address1 value:irq[0x%x] = 0x%x\n" , - pmic->irq_addr1.start_addr + i, pending1); - -hisi_pmic_write (pmic, pmic->irq_addr1.start_addr + i,HISI_MASK_STATE ); - } - } -} -static int hisi_pmic_probe (struct spmi_device *pdev) {struct device *dev = &pdev->dev;
@@ -390,7 +271,6 @@ static int hisi_pmic_probe(struct spmi_device *pdev)enum of_gpio_flags flags;int ret =0 ;int i; -unsigned int fpga_flag =0 ;unsigned int virq; pmic =devm_kzalloc (dev,sizeof (*pmic),GFP_KERNEL );
@@ -404,22 +284,10 @@ static int hisi_pmic_probe(struct spmi_device *pdev)return ret; } -/*get pmic dts the second group irq*/ - ret =get_pmic_device_tree_data1 (np, pmic); -if (ret) -dev_err (&pdev->dev,"the platform don't support ext-interrupt.\n" ); -/* TODO: get and enable clk request */ spin_lock_init (&pmic->lock); pmic->dev = dev; - ret =of_property_read_u32_array (np,"hisilicon,pmic_fpga_flag" , - &fpga_flag,1 ); -if (ret) -pr_err ("no hisilicon,pmic_fpga_flag property set\n" ); - -if (fpga_flag ==PMIC_FPGA_FLAG ) - goto after_irq_register; pmic->gpio =of_get_gpio_flags (np,0 , &flags);if (pmic->gpio <0 )
@@ -438,10 +306,6 @@ static int hisi_pmic_probe(struct spmi_device *pdev)/* mask && clear IRQ status */ hisi_pmic_irq_prc (pmic); -/*clear && mask the new adding irq*/ -hisi_pmic_irq1_prc (pmic); - - pmic->irqnum += pmic->irqnum1; pmic->irqs =devm_kzalloc (dev, pmic->irqnum *sizeof (int ),GFP_KERNEL );if (!pmic->irqs)
@@ -491,7 +355,6 @@ static int hisi_pmic_probe(struct spmi_device *pdev)return ret; } -after_irq_register:return 0 ; request_theaded_irq:
include/linux/mfd/hi6421-spmi-pmic.h +3 -11
@@ -48,19 +48,11 @@ struct hisi_pmic {struct irq_domain *domain;int irq;int gpio; -unsigned int *irqs; +unsigned int *irqs;int irqnum;int irqarray; -struct irq_mask_info irq_mask_addr; -struct irq_info irq_addr; -int irqnum1; -int irqarray1; -struct irq_mask_info irq_mask_addr1; -struct irq_info irq_addr1; -struct write_lock normal_lock; -struct write_lock debug_lock; - -unsigned int g_extinterrupt_flag; +struct irq_mask_info irq_mask_addr; +struct irq_info irq_addr; };u32 hisi_pmic_read (struct hisi_pmic *pmic,int reg);
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 25/33 regulator: hi6421v600-regulator: convert to use get/set voltage_sel
In reply to Mauro Carvalho ChehabAs the supported LDOs on this driver are all using a selector, change the implementation to use get_voltage_sel and set_voltage_sel ops.
--- drivers/regulator/hi6421v600-regulator.c | 58 +++++++++--------------- 1 file changed, 22 insertions(+), 36 deletions(-)
drivers/regulator/hi6421v600-regulator.c +22 -36
@@ -86,8 +86,8 @@ static int hi6421_spmi_regulator_enable(struct regulator_dev *rdev)/* set enable register */ hi6421_spmi_pmic_rmw (pmic, rdev->desc->enable_reg, - rdev->desc->enable_mask, - rdev->desc->enable_mask); + rdev->desc->enable_mask, + rdev->desc->enable_mask);dev_dbg (&rdev->dev,"%s: enable_reg=0x%x, enable_mask=0x%x\n" , __func__, rdev->desc->enable_reg, rdev->desc->enable_mask);
@@ -109,64 +109,49 @@ static int hi6421_spmi_regulator_disable(struct regulator_dev *rdev)return 0 ; } -static int hi6421_spmi_regulator_get_voltage (struct regulator_dev *rdev) +static int hi6421_spmi_regulator_get_voltage_sel (struct regulator_dev *rdev) {struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev);struct hi6421_spmi_pmic *pmic = sreg->pmic;u32 reg_val, selector; -int vol;/* get voltage selector */ reg_val =hi6421_spmi_pmic_read (pmic, rdev->desc->vsel_reg); - selector = (reg_val & rdev->desc->vsel_mask) >> - (ffs (rdev->desc->vsel_mask) -1 ); - vol = rdev->desc->ops->list_voltage (rdev, selector); + selector = (reg_val & rdev->desc->vsel_mask) >> (ffs (rdev->desc->vsel_mask) -1 );dev_dbg (&rdev->dev, -"%s: vsel_reg=0x%x, val=0x%x, entry=0x%x, voltage=%d mV\n" , - __func__, rdev->desc->vsel_reg, reg_val, selector, vol/1000 ); +"%s: vsel_reg=0x%x, value=0x%x, entry=0x%x, voltage=%d mV\n" , + __func__, rdev->desc->vsel_reg, reg_val, selector, + rdev->desc->ops->list_voltage (rdev, selector) /1000 ); -return vol; +return selector; } -static int hi6421_spmi_regulator_set_voltage (struct regulator_dev *rdev, -int min_uV,int max_uV,unsigned int *selector) +static int hi6421_spmi_regulator_set_voltage_sel (struct regulator_dev *rdev, +unsigned int selector) {struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev);struct hi6421_spmi_pmic *pmic = sreg->pmic; -u32 vsel; -int uV, ret =0 ; - -for (vsel =0 ; vsel < rdev->desc->n_voltages; vsel++) { - uV = rdev->desc->volt_table[vsel]; -dev_dbg (&rdev->dev, -"%s: min %d, max %d, value[%u] = %d\n" , - __func__, min_uV, max_uV, vsel, uV); - -/* Break at the first in-range value */ -if (min_uV <= uV && uV <= max_uV) -break ; - } +u32 reg_val;/* unlikely to happen. sanity test done by regulator core */ -if (unlikely (vsel == rdev->desc->n_voltages)) +if (unlikely (selector >= rdev->desc->n_voltages))return -EINVAL ; - *selector = vsel; + reg_val = selector << (ffs (rdev->desc->vsel_mask) -1 ); +/* set voltage selector */ hi6421_spmi_pmic_rmw (pmic, rdev->desc->vsel_reg, - rdev->desc->vsel_mask, - vsel << (ffs (rdev->desc->vsel_mask) -1 )); + rdev->desc->vsel_mask, reg_val);dev_dbg (&rdev->dev, -"%s: vsel_reg=0x%x, vsel_mask=0x%x, value=0x%x, voltage=%d mV\n" , +"%s: vsel_reg=0x%x, mask=0x%x, value=0x%x, voltage=%d mV\n" , __func__, - rdev->desc->vsel_reg, - rdev->desc->vsel_mask, - vsel << (ffs (rdev->desc->vsel_mask) -1 ), uV /1000 ); + rdev->desc->vsel_reg, rdev->desc->vsel_mask, reg_val, + rdev->desc->ops->list_voltage (rdev, selector) /1000 ); -return ret; +return 0 ; }static unsigned int hi6421_spmi_regulator_get_mode (struct regulator_dev *rdev)
@@ -315,8 +300,9 @@ static struct regulator_ops hi6421_spmi_ldo_rops = { .enable = hi6421_spmi_regulator_enable, .disable = hi6421_spmi_regulator_disable, .list_voltage = regulator_list_voltage_table, - .get_voltage = hi6421_spmi_regulator_get_voltage, - .set_voltage = hi6421_spmi_regulator_set_voltage, + .map_voltage = regulator_map_voltage_iterate, + .get_voltage_sel = hi6421_spmi_regulator_get_voltage_sel, + .set_voltage_sel = hi6421_spmi_regulator_set_voltage_sel, .get_mode = hi6421_spmi_regulator_get_mode, .set_mode = hi6421_spmi_regulator_set_mode, .get_optimum_mode = hi6421_spmi_regulator_get_optimum_mode,
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 23/33 regulator: hi6421v600-regulator: better handle modes
In reply to Mauro Carvalho ChehabInstead of implementing a custom set of properties, set valid_modes_mask based on having or not a mask for enabling the eco_mode.
This makes the code clearer, and remove some uneeded props from DT.
--- drivers/regulator/hi6421v600-regulator.c | 32 ++++++++---------------- 1 file changed, 10 insertions(+), 22 deletions(-)
drivers/regulator/hi6421v600-regulator.c +10 -22
@@ -338,7 +338,6 @@ static int hisi_regulator_probe_ldo(struct platform_device *pdev,struct regulator_config config = { };struct regulation_constraints *constraint;const char *supplyname =NULL ; -unsigned int temp_modes;int ret =0 ; initdata =of_get_regulator_init_data (dev, np,NULL );
@@ -347,25 +346,6 @@ static int hisi_regulator_probe_ldo(struct platform_device *pdev,return -EINVAL ; } -/* hisi regulator supports two modes */ - constraint = &initdata->constraints; - - ret =of_property_read_u32_array (np,"valid-modes-mask" , - &constraint->valid_modes_mask,1 ); -if (ret) { -dev_err (dev,"no valid modes mask\n" ); - ret = -ENODEV ; -return ret; - } - ret =of_property_read_u32_array (np,"valid-idle-mask" , - &temp_modes,1 ); -if (ret) { -dev_err (dev,"no valid idle mask\n" ); - ret = -ENODEV ; -return ret; - } - constraint->valid_ops_mask |= temp_modes; - sreg =kzalloc (sizeof (*sreg),GFP_KERNEL );if (!sreg)return -ENOMEM ;
@@ -387,6 +367,15 @@ static int hisi_regulator_probe_ldo(struct platform_device *pdev,if (ret) goto hisi_probe_end; +/* hisi regulator supports two modes */ + constraint = &initdata->constraints; + + constraint->valid_modes_mask =REGULATOR_MODE_NORMAL ; +if (sreg->eco_mode_mask) { + constraint->valid_modes_mask |=REGULATOR_MODE_IDLE ; + constraint->valid_ops_mask |=REGULATOR_CHANGE_MODE ; + } + config.dev = &pdev->dev; config.init_data = initdata; config.driver_data = sreg;
@@ -401,8 +390,7 @@ static int hisi_regulator_probe_ldo(struct platform_device *pdev, goto hisi_probe_end; } -dev_dbg (dev,"%s:valid_modes_mask: 0x%x, valid_ops_mask: 0x%x\n" , - rdesc->name, +dev_dbg (dev,"valid_modes_mask: 0x%x, valid_ops_mask: 0x%x\n" , constraint->valid_modes_mask, constraint->valid_ops_mask);dev_set_drvdata (dev, rdev);
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 13/33 mfd, regulator: coding style fixups at the HiSilicon SPMI PMIC code
In reply to Mauro Carvalho ChehabThere are several issues on those drivers related to their coding style. Solve most of them.
--- drivers/mfd/hisi_pmic_spmi.c | 126 ++++++++++++------------ drivers/regulator/hisi_regulator_spmi.c | 110 +++++++++++---------- include/linux/mfd/hisi_pmic.h | 18 +--- 3 files changed, 120 insertions(+), 134 deletions(-)
drivers/mfd/hisi_pmic_spmi.c +61 -65
@@ -1,3 +1,4 @@ +// SPDX-License-Identifier: GPL-2.0 /* * Device driver for regulators in HISI PMIC IC *
@@ -76,7 +77,8 @@ u32 hisi_pmic_read(struct hisi_pmic *pmic, int reg)return 0 ; } - ret =spmi_ext_register_readl (pdev, reg, (unsigned char *)&read_value,1 );/*lint !e734 !e732 */ + ret =spmi_ext_register_readl (pdev, reg, + (unsigned char *)&read_value,1 );if (ret) {pr_err ("%s: spmi_ext_register_readl failed!\n" , __func__);return 0 ;
@@ -96,7 +98,7 @@ void hisi_pmic_write(struct hisi_pmic *pmic, int reg, u32 val)return ; } - ret =spmi_ext_register_writel (pdev, reg, (unsigned char *)&val,1 );/*lint !e734 !e732 */ + ret =spmi_ext_register_writel (pdev, reg, (unsigned char *)&val,1 );if (ret) {pr_err ("%s: spmi_ext_register_writel failed!\n" , __func__);return ;
@@ -126,14 +128,13 @@ static irqreturn_t hisi_irq_handler(int irq, void *data)for (i =0 ; i < pmic->irqarray; i++) { pending =hisi_pmic_read (pmic, (i + pmic->irq_addr.start_addr)); pending &=HISI_MASK_FIELD ; -if (pending !=0 ) { -pr_info ("pending[%d]=0x%lx\n\r" , i, pending); - } +if (pending !=0 ) +pr_debug ("pending[%d]=0x%lx\n\r" , i, pending);hisi_pmic_write (pmic, (i + pmic->irq_addr.start_addr), pending); -/*solve powerkey order*/ -if ((HISI_IRQ_KEY_NUM == i) && ((pending &HISI_IRQ_KEY_VALUE ) ==HISI_IRQ_KEY_VALUE )) { +/* solve powerkey order */ +if ((i ==HISI_IRQ_KEY_NUM ) && ((pending &HISI_IRQ_KEY_VALUE ) ==HISI_IRQ_KEY_VALUE )) {generic_handle_irq (pmic->irqs[HISI_IRQ_KEY_DOWN ]);generic_handle_irq (pmic->irqs[HISI_IRQ_KEY_UP ]); pending &= (~HISI_IRQ_KEY_VALUE );
@@ -141,7 +142,7 @@ static irqreturn_t hisi_irq_handler(int irq, void *data)if (pending) {for_each_set_bit (offset, &pending,HISI_BITS ) -generic_handle_irq (pmic->irqs[offset + i *HISI_BITS ]);/*lint !e679 */ +generic_handle_irq (pmic->irqs[offset + i *HISI_BITS ]); } }
@@ -150,16 +151,16 @@ static irqreturn_t hisi_irq_handler(int irq, void *data)for (i =0 ; i < pmic->irqarray1; i++) { pending =hisi_pmic_read (pmic, (i + pmic->irq_addr1.start_addr)); pending &=HISI_MASK_FIELD ; -if (pending !=0 ) { -pr_info ("pending[%d]=0x%lx\n\r" , i, pending); - } +if (pending !=0 ) +pr_debug ("pending[%d]=0x%lx\n\r" , i, pending);hisi_pmic_write (pmic, (i + pmic->irq_addr1.start_addr), pending); -if (pending) { -for_each_set_bit (offset, &pending,HISI_BITS ) -generic_handle_irq (pmic->irqs[offset + (i+HISI_PMIC_FIRST_GROUP_INT_NUM ) *HISI_BITS ]);/*lint !e679 */ - } +if (!pending) +continue ; + +for_each_set_bit (offset, &pending,HISI_BITS ) +generic_handle_irq (pmic->irqs[offset + (i +HISI_PMIC_FIRST_GROUP_INT_NUM ) *HISI_BITS ]); } }
@@ -174,11 +175,16 @@ static void hisi_irq_mask(struct irq_data *d) offset = (irqd_to_hwirq (d) >>3 );if (pmic->g_extinterrupt_flag ==1 ) { -if (offset <HISI_PMIC_FIRST_GROUP_INT_NUM ) +if (offset <HISI_PMIC_FIRST_GROUP_INT_NUM ) { offset += pmic->irq_mask_addr.start_addr; -else /*Change addr when irq num larger than 16 because interrupt addr is nonsequence*/ - offset = offset+(pmic->irq_mask_addr1.start_addr)-HISI_PMIC_FIRST_GROUP_INT_NUM ; - }else { + }else { +/* +* Change addr when irq num larger than 16 because +* interrupt addr is nonsequence +*/ + offset = offset + (pmic->irq_mask_addr1.start_addr) -HISI_PMIC_FIRST_GROUP_INT_NUM ; + } + }else { offset += pmic->irq_mask_addr.start_addr; }spin_lock_irqsave (&pmic->lock, flags);
@@ -199,8 +205,8 @@ static void hisi_irq_unmask(struct irq_data *d)if (offset <HISI_PMIC_FIRST_GROUP_INT_NUM ) offset += pmic->irq_mask_addr.start_addr;else - offset = offset+(pmic->irq_mask_addr1.start_addr)-HISI_PMIC_FIRST_GROUP_INT_NUM ; - }else { + offset = offset + (pmic->irq_mask_addr1.start_addr) -HISI_PMIC_FIRST_GROUP_INT_NUM ; + }else { offset += pmic->irq_mask_addr.start_addr; }spin_lock_irqsave (&pmic->lock, flags);
@@ -219,7 +225,7 @@ static struct irq_chip hisi_pmu_irqchip = { };static int hisi_irq_map (struct irq_domain *d,unsigned int virq, -irq_hw_number_t hw) +irq_hw_number_t hw) {struct hisi_pmic *pmic = d->host_data;
@@ -231,19 +237,18 @@ static int hisi_irq_map(struct irq_domain *d, unsigned int virq,return 0 ; } -static struct irq_domain_ops hisi_domain_ops = { +static const struct irq_domain_ops hisi_domain_ops = { .map = hisi_irq_map, .xlate = irq_domain_xlate_twocell, }; -/*lint -e570 -e64*/ static int get_pmic_device_tree_data (struct device_node *np,struct hisi_pmic *pmic) {int ret =0 ;/*get pmic irq num*/ ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-irq-num" , - &(pmic->irqnum),1 ); + &pmic->irqnum,1 );if (ret) {pr_err ("no hisilicon,hisi-pmic-irq-num property set\n" ); ret = -ENODEV ;
@@ -252,7 +257,7 @@ static int get_pmic_device_tree_data(struct device_node *np, struct hisi_pmic *p/*get pmic irq array number*/ ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-irq-array" , - &(pmic->irqarray),1 ); + &pmic->irqarray,1 );if (ret) {pr_err ("no hisilicon,hisi-pmic-irq-array property set\n" ); ret = -ENODEV ;
@@ -261,7 +266,7 @@ static int get_pmic_device_tree_data(struct device_node *np, struct hisi_pmic *p/*SOC_PMIC_IRQ_MASK_0_ADDR*/ ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-irq-mask-addr" , - (int *)&pmic->irq_mask_addr,2 ); + (int *)&pmic->irq_mask_addr,2 );if (ret) {pr_err ("no hisilicon,hisi-pmic-irq-mask-addr property set\n" ); ret = -ENODEV ;
@@ -270,7 +275,7 @@ static int get_pmic_device_tree_data(struct device_node *np, struct hisi_pmic *p/*SOC_PMIC_IRQ0_ADDR*/ ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-irq-addr" , - (int *)&pmic->irq_addr,2 ); + (int *)&pmic->irq_addr,2 );if (ret) {pr_err ("no hisilicon,hisi-pmic-irq-addr property set\n" ); ret = -ENODEV ;
@@ -279,7 +284,7 @@ static int get_pmic_device_tree_data(struct device_node *np, struct hisi_pmic *p/*pmic lock*/ ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-lock" , - (int *)&pmic->normal_lock,2 ); + (int *)&pmic->normal_lock,2 );if (ret) {pr_err ("no hisilicon,hisi-pmic-lock property set\n" ); ret = -ENODEV ;
@@ -288,7 +293,7 @@ static int get_pmic_device_tree_data(struct device_node *np, struct hisi_pmic *p/*pmic debug lock*/ ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-debug-lock" , - (int *)&pmic->debug_lock,2 ); + (int *)&pmic->debug_lock,2 );if (ret) {pr_err ("no hisilicon,hisi-pmic-debug-lock property set\n" ); ret = -ENODEV ;
@@ -296,17 +301,15 @@ static int get_pmic_device_tree_data(struct device_node *np, struct hisi_pmic *p }return ret; -}/*lint -restore*/ +} - -/*lint -e570 -e64*/ static int get_pmic_device_tree_data1 (struct device_node *np,struct hisi_pmic *pmic) {int ret =0 ;/*get pmic irq num*/ ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-irq-num1" , - &(pmic->irqnum1),1 ); + &pmic->irqnum1,1 );if (ret) {pr_err ("no hisilicon,hisi-pmic-irq-num1 property set\n" ); ret = -ENODEV ;
@@ -316,7 +319,7 @@ static int get_pmic_device_tree_data1(struct device_node *np, struct hisi_pmic */*get pmic irq array number*/ ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-irq-array1" , - &(pmic->irqarray1),1 ); + &pmic->irqarray1,1 );if (ret) {pr_err ("no hisilicon,hisi-pmic-irq-array1 property set\n" ); ret = -ENODEV ;
@@ -325,7 +328,7 @@ static int get_pmic_device_tree_data1(struct device_node *np, struct hisi_pmic */*SOC_PMIC_IRQ_MASK_0_ADDR*/ ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-irq-mask-addr1" , - (int *)&pmic->irq_mask_addr1,2 ); + (int *)&pmic->irq_mask_addr1,2 );if (ret) {pr_err ("no hisilicon,hisi-pmic-irq-mask-addr1 property set\n" ); ret = -ENODEV ;
@@ -334,7 +337,7 @@ static int get_pmic_device_tree_data1(struct device_node *np, struct hisi_pmic */*SOC_PMIC_IRQ0_ADDR*/ ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-irq-addr1" , - (int *)&pmic->irq_addr1,2 ); + (int *)&pmic->irq_addr1,2 );if (ret) {pr_err ("no hisilicon,hisi-pmic-irq-addr1 property set\n" ); ret = -ENODEV ;
@@ -343,21 +346,22 @@ static int get_pmic_device_tree_data1(struct device_node *np, struct hisi_pmic * pmic->g_extinterrupt_flag =1 ;return ret; -}/*lint -restore*/ +}static void hisi_pmic_irq_prc (struct hisi_pmic *pmic) {int i; -for (i =0 ; i < pmic->irq_mask_addr.array; i++) { + +for (i =0 ; i < pmic->irq_mask_addr.array; i++)hisi_pmic_write (pmic, pmic->irq_mask_addr.start_addr + i,HISI_MASK_STATE ); - }for (i =0 ; i < pmic->irq_addr.array; i++) {unsigned int pending =hisi_pmic_read (pmic, pmic->irq_addr.start_addr + i); -pr_debug ("PMU IRQ address value:irq[0x%x] = 0x%x\n" , pmic->irq_addr.start_addr + i, pending); + +pr_debug ("PMU IRQ address value:irq[0x%x] = 0x%x\n" , + pmic->irq_addr.start_addr + i, pending);hisi_pmic_write (pmic, pmic->irq_addr.start_addr + i,HISI_MASK_STATE ); } - }static void hisi_pmic_irq1_prc (struct hisi_pmic *pmic)
@@ -371,7 +375,10 @@ static void hisi_pmic_irq1_prc(struct hisi_pmic *pmic)for (i =0 ; i < pmic->irq_addr1.array; i++) { pending1 =hisi_pmic_read (pmic, pmic->irq_addr1.start_addr + i); -pr_debug ("PMU IRQ address1 value:irq[0x%x] = 0x%x\n" , pmic->irq_addr1.start_addr + i, pending1); + +pr_debug ("PMU IRQ address1 value:irq[0x%x] = 0x%x\n" , + pmic->irq_addr1.start_addr + i, pending1); +hisi_pmic_write (pmic, pmic->irq_addr1.start_addr + i,HISI_MASK_STATE ); } }
@@ -389,23 +396,20 @@ static int hisi_pmic_probe(struct spmi_device *pdev)unsigned int virq; pmic =devm_kzalloc (dev,sizeof (*pmic),GFP_KERNEL ); -if (!pmic) { -dev_err (dev,"cannot allocate hisi_pmic device info\n" ); +if (!pmic)return -ENOMEM ; - }/*TODO: get pmic dts info*/ ret =get_pmic_device_tree_data (np, pmic);if (ret) { -dev_err (&pdev->dev,"Error reading hisi pmic dts \n" ); +dev_err (&pdev->dev,"Error reading hisi pmic dts\n" );return ret; }/*get pmic dts the second group irq*/ ret =get_pmic_device_tree_data1 (np, pmic); -if (ret) { +if (ret)dev_err (&pdev->dev,"the platform don't support ext-interrupt.\n" ); - }/* TODO: get and enable clk request */ spin_lock_init (&pmic->lock);
@@ -416,9 +420,8 @@ static int hisi_pmic_probe(struct spmi_device *pdev)if (ret)pr_err ("no hisilicon,pmic_fpga_flag property set\n" ); -if (PMIC_FPGA_FLAG == fpga_flag) { +if (fpga_flag ==PMIC_FPGA_FLAG ) goto after_irq_register; - } pmic->gpio =of_get_gpio_flags (np,0 , &flags);if (pmic->gpio <0 )
@@ -442,12 +445,9 @@ static int hisi_pmic_probe(struct spmi_device *pdev) pmic->irqnum += pmic->irqnum1; - pmic->irqs = (unsigned int *)devm_kmalloc (dev, pmic->irqnum *sizeof (int ),GFP_KERNEL ); -if (!pmic->irqs) { -pr_err ("%s:Failed to alloc memory for pmic irq number!\n" , __func__); + pmic->irqs =devm_kzalloc (dev, pmic->irqnum *sizeof (int ),GFP_KERNEL ); +if (!pmic->irqs) goto irq_malloc; - } -memset (pmic->irqs,0 , pmic->irqnum); pmic->domain =irq_domain_add_simple (np, pmic->irqnum,0 , &hisi_domain_ops, pmic);
@@ -469,7 +469,7 @@ static int hisi_pmic_probe(struct spmi_device *pdev) } ret =request_threaded_irq (pmic->irq, hisi_irq_handler,NULL , -IRQF_TRIGGER_LOW |IRQF_SHARED |IRQF_NO_SUSPEND , +IRQF_TRIGGER_LOW |IRQF_SHARED |IRQF_NO_SUSPEND ,"pmic" , pmic);if (ret <0 ) {dev_err (dev,"could not claim pmic %d\n" , ret);
@@ -480,7 +480,6 @@ static int hisi_pmic_probe(struct spmi_device *pdev) after_irq_register:return 0 ; - request_theaded_irq: irq_create_mapping: irq_domain:
@@ -491,19 +490,18 @@ static int hisi_pmic_probe(struct spmi_device *pdev)static void hisi_pmic_remove (struct spmi_device *pdev) { -struct hisi_pmic *pmic =dev_get_drvdata (&pdev->dev);free_irq (pmic->irq, pmic);gpio_free (pmic->gpio);devm_kfree (&pdev->dev, pmic); - } +static int hisi_pmic_suspend (struct device *dev,pm_message_t state) {struct hisi_pmic *pmic =dev_get_drvdata (dev); -if (NULL == pmic) { +if (!pmic) {pr_err ("%s:pmic is NULL\n" , __func__);return -ENOMEM ; }
@@ -512,13 +510,13 @@ static int hisi_pmic_suspend(struct device *dev, pm_message_t state)pr_info ("%s:-\n" , __func__);return 0 ; -}/*lint !e715 */ +}static int hisi_pmic_resume (struct device *dev) {struct hisi_pmic *pmic =dev_get_drvdata (dev); -if (NULL == pmic) { +if (!pmic) {pr_err ("%s:pmic is NULL\n" , __func__);return -ENOMEM ; }
@@ -552,10 +550,8 @@ static void __exit hisi_pmic_exit(void)spmi_driver_unregister (&hisi_pmic_driver); } -subsys_initcall_sync (hisi_pmic_init);module_exit (hisi_pmic_exit);MODULE_DESCRIPTION ("PMIC driver" );MODULE_LICENSE ("GPL v2" ); -
drivers/regulator/hisi_regulator_spmi.c +56 -54
298 lines not on this page · raw message
include/linux/mfd/hisi_pmic.h +3 -15
@@ -1,3 +1,4 @@ +/* SPDX-License-Identifier: GPL-2.0 */ /* * Header file for device driver Hi6421 PMIC *
@@ -5,19 +6,6 @@* Copyright (C) 2011 Hisilicon. * * Guodong Xu <[email protected]> -* -* This program is free software; you can redistribute it and/or modify -* it under the terms of the GNU General Public License version 2 as -* published by the Free Software Foundation. -* -* This program is distributed in the hope that it will be useful, -* but WITHOUT ANY WARRANTY; without even the implied warranty of -* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -* GNU General Public License for more details. -* -* You should have received a copy of the GNU General Public License along -* with this program; if not, write to the Free Software Foundation, Inc., -* 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. */ #ifndef __HISI_PMIC_H
@@ -25,12 +13,12 @@#include <linux/irqdomain.h> -#define HISI_REGS_ENA_PROTECT_TIME (0)/* in microseconds */ +#define HISI_REGS_ENA_PROTECT_TIME (0)/* in microseconds */ #define HISI_ECO_MODE_ENABLE (1)#define HISI_ECO_MODE_DISABLE (0)typedef int (*pmic_ocp_callback )(char *); -extern int hisi_pmic_special_ocp_register (char *power_name,pmic_ocp_callback handler); +int hisi_pmic_special_ocp_register (char *power_name,pmic_ocp_callback handler);struct irq_mask_info {int start_addr;
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 21/33 regulator: hi6421v600-regulator: cleanup debug messages
In reply to Mauro Carvalho Chehab- use dev_foo() instead of pr_foo();
- cleanup the messages, making them more standard and easier to understand.
--- drivers/regulator/hi6421v600-regulator.c | 76 +++++++++++++++--------- 1 file changed, 47 insertions(+), 29 deletions(-)
drivers/regulator/hi6421v600-regulator.c +47 -29
@@ -59,9 +59,11 @@ static int hisi_regulator_is_enabled(struct regulator_dev *rdev)struct hisi_pmic *pmic = sreg->pmic; reg_val =hisi_pmic_read (pmic, rdev->desc->enable_reg); -pr_debug ("<[%s]: enable_reg=0x%x,enable_state=%d>\n" , + +dev_dbg (&rdev->dev, +"%s: enable_reg=0x%x, val= 0x%x, enable_state=%d\n" , __func__, rdev->desc->enable_reg, - (reg_val & rdev->desc->enable_mask)); + reg_val, (reg_val & rdev->desc->enable_mask));return ((reg_val & rdev->desc->enable_mask) !=0 ); }
@@ -74,7 +76,8 @@ static int hisi_regulator_enable(struct regulator_dev *rdev)/* keep a distance of off_on_delay from last time disabled */ usleep_range (rdev->desc->off_on_delay, rdev->desc->off_on_delay +1000 ); -pr_debug ("<[%s]: off_on_delay=%dus>\n" , __func__, rdev->desc->off_on_delay); +dev_dbg (&rdev->dev,"%s: off_on_delay=%d us\n" , + __func__, rdev->desc->off_on_delay);/* cannot enable more than one regulator at one time */ mutex_lock (&enable_mutex);
@@ -85,7 +88,7 @@ static int hisi_regulator_enable(struct regulator_dev *rdev)hisi_pmic_rmw (pmic, rdev->desc->enable_reg, rdev->desc->enable_mask, rdev->desc->enable_mask); -pr_debug ("<[%s]: enable_reg=0x%x,enable_mask=0x%x>\n" , +dev_dbg (&rdev->dev,"%s: enable_reg=0x%x, enable_mask=0x%x\n" , __func__, rdev->desc->enable_reg, rdev->desc->enable_mask);
@@ -111,16 +114,20 @@ static int hisi_regulator_get_voltage(struct regulator_dev *rdev)struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev);struct hisi_pmic *pmic = sreg->pmic;u32 reg_val, selector; +int vol;/* get voltage selector */ reg_val =hisi_pmic_read (pmic, rdev->desc->vsel_reg); -pr_debug ("<[%s]: vsel_reg=0x%x>\n" , - __func__, rdev->desc->vsel_reg); - selector = (reg_val & rdev->desc->vsel_mask) >> (ffs (rdev->desc->vsel_mask) -1 ); -return rdev->desc->ops->list_voltage (rdev, selector); + vol = rdev->desc->ops->list_voltage (rdev, selector); + +dev_dbg (&rdev->dev, +"%s: vsel_reg=0x%x, val=0x%x, entry=0x%x, voltage=%d mV\n" , + __func__, rdev->desc->vsel_reg, reg_val, selector, vol/1000 ); + +return vol; } static int hisi_regulator_set_voltage(struct regulator_dev *rdev,
@@ -129,10 +136,14 @@ static int hisi_regulator_set_voltage(struct regulator_dev *rdev,struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev);struct hisi_pmic *pmic = sreg->pmic;u32 vsel; -int ret =0 ; +int uV, ret =0 ;for (vsel =0 ; vsel < rdev->desc->n_voltages; vsel++) { -int uV = rdev->desc->volt_table[vsel]; + uV = rdev->desc->volt_table[vsel]; +dev_dbg (&rdev->dev, +"%s: min %d, max %d, value[%u] = %d\n" , + __func__, min_uV, max_uV, vsel, uV); +/* Break at the first in-range value */ if (min_uV <= uV && uV <= max_uV)break ;
@@ -146,13 +157,14 @@ static int hisi_regulator_set_voltage(struct regulator_dev *rdev,/* set voltage selector */ hisi_pmic_rmw (pmic, rdev->desc->vsel_reg, rdev->desc->vsel_mask, - vsel << (ffs (rdev->desc->vsel_mask) -1 )); + vsel << (ffs (rdev->desc->vsel_mask) -1 )); -pr_debug ("<[%s]: vsel_reg=0x%x, vsel_mask=0x%x, value=0x%x>\n" , +dev_dbg (&rdev->dev, +"%s: vsel_reg=0x%x, vsel_mask=0x%x, value=0x%x, voltage=%d mV\n" , __func__, rdev->desc->vsel_reg, rdev->desc->vsel_mask, - vsel << (ffs (rdev->desc->vsel_mask) -1 )); + vsel << (ffs (rdev->desc->vsel_mask) -1 ), uV /1000 );return ret; }
@@ -162,17 +174,21 @@ static unsigned int hisi_regulator_get_mode(struct regulator_dev *rdev)struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev);struct hisi_pmic *pmic = sreg->pmic;u32 reg_val; +unsigned int mode; reg_val =hisi_pmic_read (pmic, rdev->desc->enable_reg); -pr_debug ("<[%s]: reg_val=%d, enable_reg=0x%x, eco_mode_mask=0x%x>\n" , - __func__, reg_val, - rdev->desc->enable_reg, - sreg->eco_mode_mask);if (reg_val & sreg->eco_mode_mask) -return REGULATOR_MODE_IDLE ; + mode =REGULATOR_MODE_IDLE ;else -return REGULATOR_MODE_NORMAL ; + mode =REGULATOR_MODE_NORMAL ; + +dev_dbg (&rdev->dev, +"%s: enable_reg=0x%x, eco_mode_mask=0x%x, reg_val=0x%x, %s mode\n" , + __func__, rdev->desc->enable_reg, sreg->eco_mode_mask, reg_val, + mode ==REGULATOR_MODE_IDLE ?"idle" :"normal" ); + +return mode; } static int hisi_regulator_set_mode(struct regulator_dev *rdev,
@@ -198,7 +214,8 @@ static int hisi_regulator_set_mode(struct regulator_dev *rdev, sreg->eco_mode_mask, eco_mode << (ffs(sreg->eco_mode_mask) - 1)); - pr_debug("<[%s]: enable_reg=0x%x, eco_mode_mask=0x%x, value=0x%x>\n", + dev_dbg(&rdev->dev, + "%s: enable_reg=0x%x, eco_mode_mask=0x%x, value=0x%x\n", __func__, rdev->desc->enable_reg, sreg->eco_mode_mask,
@@ -212,10 +229,13 @@ static unsigned int hisi_regulator_get_optimum_mode(struct regulator_dev *rdev, {struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev); -if (load_uA || ((unsigned int )load_uA > sreg->eco_uA)) +if (load_uA || ((unsigned int )load_uA > sreg->eco_uA)) { +dev_dbg (&rdev->dev,"%s: normal mode" , __func__);return REGULATOR_MODE_NORMAL ; -else + }else { +dev_dbg (&rdev->dev,"%s: idle mode" , __func__);return REGULATOR_MODE_IDLE ; + } } static int hisi_dt_parse(struct platform_device *pdev,
@@ -333,7 +353,7 @@ static int hisi_regulator_probe_ldo(struct platform_device *pdev, initdata =of_get_regulator_init_data (dev, np,NULL );if (!initdata) { -pr_err ("get regulator init data error !\n" ); +dev_err (dev,"failed to get regulator data\n" );return -EINVAL ; }
@@ -343,14 +363,14 @@ static int hisi_regulator_probe_ldo(struct platform_device *pdev, ret =of_property_read_u32_array (np,"hisilicon,valid-modes-mask" , &constraint->valid_modes_mask,1 );if (ret) { -pr_err ("no hisilicon,valid-modes-mask property set\n" ); +dev_err (dev,"no valid modes mask\n" ); ret = -ENODEV ;return ret; } ret =of_property_read_u32_array (np,"hisilicon,valid-idle-mask" , &temp_modes,1 );if (ret) { -pr_err ("no hisilicon,valid-modes-mask property set\n" ); +dev_err (dev,"no valid idle mask\n" ); ret = -ENODEV ;return ret; }
@@ -374,10 +394,8 @@ static int hisi_regulator_probe_ldo(struct platform_device *pdev,/* parse device tree data for regulator specific */ ret =hisi_dt_parse (pdev, sreg, rdesc); -if (ret) { -dev_err (dev,"device tree parameter parse error!\n" ); +if (ret) goto hisi_probe_end; - } config.dev = &pdev->dev; config.init_data = initdata;
@@ -393,7 +411,7 @@ static int hisi_regulator_probe_ldo(struct platform_device *pdev, goto hisi_probe_end; } -pr_debug ("[%s]:valid_modes_mask[0x%x], valid_ops_mask[0x%x]\n" , +dev_dbg (dev,"%s:valid_modes_mask: 0x%x, valid_ops_mask: 0x%x\n" , rdesc->name, constraint->valid_modes_mask, constraint->valid_ops_mask);
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 19/33 spmi: hi6421-spmi-pmic: cleanup OF properties
In reply to Mauro Carvalho ChehabSimplify the names of the DT properties and do some cleanups, in order to better document them.
--- drivers/mfd/hi6421-spmi-pmic.c | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-)
drivers/mfd/hi6421-spmi-pmic.c +8 -8
@@ -209,37 +209,37 @@ static int get_pmic_device_tree_data(struct device_node *np, struct hisi_pmic *pint ret =0 ;/*get pmic irq num*/ - ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-irq-num" , + ret =of_property_read_u32_array (np,"irq-num" , &pmic->irqnum,1 );if (ret) { -pr_err ("no hisilicon,hisi-pmic-irq-num property set\n" ); +pr_err ("no irq-num property set\n" ); ret = -ENODEV ;return ret; }/*get pmic irq array number*/ - ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-irq-array" , + ret =of_property_read_u32_array (np,"irq-array" , &pmic->irqarray,1 );if (ret) { -pr_err ("no hisilicon,hisi-pmic-irq-array property set\n" ); +pr_err ("no irq-array property set\n" ); ret = -ENODEV ;return ret; }/*SOC_PMIC_IRQ_MASK_0_ADDR*/ - ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-irq-mask-addr" , + ret =of_property_read_u32_array (np,"irq-mask-addr" , (int *)&pmic->irq_mask_addr,2 );if (ret) { -pr_err ("no hisilicon,hisi-pmic-irq-mask-addr property set\n" ); +pr_err ("no irq-mask-addr property set\n" ); ret = -ENODEV ;return ret; }/*SOC_PMIC_IRQ0_ADDR*/ - ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-irq-addr" , + ret =of_property_read_u32_array (np,"irq-addr" , (int *)&pmic->irq_addr,2 );if (ret) { -pr_err ("no hisilicon,hisi-pmic-irq-addr property set\n" ); +pr_err ("no irq-addr property set\n" ); ret = -ENODEV ;return ret; }
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 4/33 mfd, regulator: get rid of unused code at HiSilicon SPMI PMIC
In reply to Mauro Carvalho ChehabThere are some checks there which could make sense for downstream builds, but doesn't make much sense for upstream ones. They came from the official Hikey970 tree from Linaro, but even there, the commented-out code is not set via other Kconfig vars.
So, let's just get rid of that. If needed later, this patch can be (partially?) reversed.
--- drivers/mfd/hisi_pmic_spmi.c | 63 -------- drivers/regulator/hisi_regulator_spmi.c | 196 +----------------------- include/linux/mfd/hisi_pmic.h | 42 ----- 3 files changed, 8 insertions(+), 293 deletions(-)
drivers/mfd/hisi_pmic_spmi.c +0 -63
@@ -53,10 +53,6 @@#define HISI_PMIC_FIRST_GROUP_INT_NUM 2static struct bit_info g_pmic_vbus = {0 }; -#ifndef BIT -#define BIT (x) (0x1U << (x)) -#endif -static struct hisi_pmic *g_pmic;static unsigned int g_extinterrupt_flag =0 ;static struct of_device_id of_hisi_pmic_match_tbl[] = {
@@ -121,65 +117,6 @@ void hisi_pmic_write(struct hisi_pmic *pmic, int reg, u32 val) }EXPORT_SYMBOL (hisi_pmic_write); -#ifdef CONFIG_HISI_DIEID -u32 hisi_pmic_read_sub_pmu (u8 sid,int reg) -{ -u32 ret; -u8 read_value =0 ; -struct spmi_device *pdev; - -if (strstr (saved_command_line,"androidboot.swtype=factory" )) - { -if (NULL == g_pmic) { -pr_err (" g_pmic is NULL\n" ); -return -1 ;/*lint !e570 */ - } - - pdev =to_spmi_device (g_pmic->dev); -if (NULL == pdev) { -pr_err ("%s:pdev get failed!\n" , __func__); -return -1 ;/*lint !e570 */ - } - - ret =spmi_ext_register_readl (pdev->ctrl, sid, reg, (unsigned char *)&read_value,1 );/*lint !e734 !e732 */ -if (ret) { -pr_err ("%s:spmi_ext_register_readl failed!\n" , __func__); -return ret; - } -return (u32 )read_value; - } -return 0 ; -} -EXPORT_SYMBOL (hisi_pmic_read_sub_pmu); - -void hisi_pmic_write_sub_pmu (u8 sid,int reg,u32 val) -{ -u32 ret; -struct spmi_device *pdev; -if (strstr (saved_command_line,"androidboot.swtype=factory" )) - { -if (NULL == g_pmic) { -pr_err (" g_pmic is NULL\n" ); -return ; - } - - pdev =to_spmi_device (g_pmic->dev); -if (NULL == pdev) { -pr_err ("%s:pdev get failed!\n" , __func__); -return ; - } - - ret =spmi_ext_register_writel (pdev->ctrl, sid, reg, (unsigned char *)&val,1 );/*lint !e734 !e732 */ -if (ret) { -pr_err ("%s:spmi_ext_register_writel failed!\n" , __func__); -return ; - } - } - -return ; -} -EXPORT_SYMBOL (hisi_pmic_write_sub_pmu); -#endif void hisi_pmic_rmw (struct hisi_pmic *pmic,int reg,u32 mask,u32 bits)
drivers/regulator/hisi_regulator_spmi.c +8 -188
276 lines not on this page · raw message
include/linux/mfd/hisi_pmic.h +0 -42
66 lines not on this page · raw message
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 3/33 spmi: hisi-spmi-controller: coding style fixup
In reply to Mauro Carvalho ChehabIn order to prepare for upstream, fix most coding style issues.
--- drivers/spmi/hisi-spmi-controller.c | 179 +++++++++++++--------------- 1 file changed, 82 insertions(+), 97 deletions(-)
drivers/spmi/hisi-spmi-controller.c +82 -97
@@ -1,3 +1,4 @@ +// SPDX-License-Identifier: GPL-2.0 #include <linux/delay.h> #include <linux/err.h>
@@ -21,7 +22,7 @@#define SPMI_SLAVE_OFFSET 0x20#define SPMI_APB_SPMI_CMD_BASE_ADDR 0x0100 -/*lint -e750 -esym(750,*)*/ +#define SPMI_APB_SPMI_WDATA0_BASE_ADDR 0x0104#define SPMI_APB_SPMI_WDATA1_BASE_ADDR 0x0108#define SPMI_APB_SPMI_WDATA2_BASE_ADDR 0x010c
@@ -33,25 +34,25 @@#define SPMI_APB_SPMI_RDATA1_BASE_ADDR 0x0208#define SPMI_APB_SPMI_RDATA2_BASE_ADDR 0x020c#define SPMI_APB_SPMI_RDATA3_BASE_ADDR 0x0210 -/*lint +e750 -esym(750,*)*/ #define SPMI_PER_DATAREG_BYTE 4/* * SPMI cmd register */ -#define SPMI_APB_SPMI_CMD_EN (1 << 31) +#define SPMI_APB_SPMI_CMD_EN BIT(31)#define SPMI_APB_SPMI_CMD_TYPE_OFFSET 24#define SPMI_APB_SPMI_CMD_LENGTH_OFFSET 20#define SPMI_APB_SPMI_CMD_SLAVEID_OFFSET 16#define SPMI_APB_SPMI_CMD_ADDR_OFFSET 0 -#define Tranverse32 (X ) ((((u32)(X) & 0xff000000) >> 24) | \ - (((u32)(X) & 0x00ff0000) >> 8) | \ - (((u32)(X) & 0x0000ff00) << 8) | \ - (((u32)(X) & 0x000000ff) << 24)) +#define bswap_32 (X ) \ + ((((u32)(X) & 0xff000000) >> 24) | \ + (((u32)(X) & 0x00ff0000) >> 8) | \ + (((u32)(X) & 0x0000ff00) << 8) | \ + (((u32)(X) & 0x000000ff) << 24))/* Command Opcodes */ -/*lint -e749 -esym(749,*)*/ +enum spmi_controller_cmd_op_code {SPMI_CMD_REG_ZERO_WRITE =0 ,SPMI_CMD_REG_WRITE =1 ,
@@ -65,13 +66,12 @@ enum spmi_controller_cmd_op_code {SPMI_CMD_REG_SHUTDOWN =9 , SPMI_CMD_REG_WAKEUP = 10, }; -/*lint +e749 -esym(749,*)*/ /* * SPMI status register */ -#define SPMI_APB_TRANS_DONE (1 << 0) -#define SPMI_APB_TRANS_FAIL (1 << 2) +#define SPMI_APB_TRANS_DONE BIT(0) +#define SPMI_APB_TRANS_FAIL BIT(2)/* Command register fields */ #define SPMI_CONTROLLER_CMD_MAX_BYTE_COUNT 16
@@ -80,16 +80,6 @@ enum spmi_controller_cmd_op_code {#define SPMI_CONTROLLER_TIMEOUT_US 1000#define SPMI_CONTROLLER_MAX_TRANS_BYTES (16) -#define SPMI_WRITEL ( dev, reg, addr ) \ - do { \ - writel( ( reg ), ( addr ) ); \ - } while (0) - -#define SPMI_READL ( dev, reg, addr ) \ - do { \ - reg = readl( addr ); \ - } while (0) -/* * @base base address of the PMIC Arbiter core registers. * @rdbase, @wrbase base address of the PMIC Arbiter read core registers.
@@ -120,7 +110,7 @@ struct spmi_controller_dev { };static int spmi_controller_wait_for_done (struct spmi_controller_dev *ctrl_dev, -void __iomem *base,u8 sid,u16 addr) +void __iomem *base,u8 sid,u16 addr) {u32 status =0 ;u32 timeout =SPMI_CONTROLLER_TIMEOUT_US ;
@@ -128,7 +118,7 @@ static int spmi_controller_wait_for_done(struct spmi_controller_dev *ctrl_dev, +SPMI_SLAVE_OFFSET * sid;while (timeout--) { -SPMI_READL (ctrl_dev->dev, status, base + offset);/*lint !e732 */ + status =readl (base + offset);if (status &SPMI_APB_TRANS_DONE ) {if (status &SPMI_APB_TRANS_FAIL ) {
@@ -139,23 +129,23 @@ static int spmi_controller_wait_for_done(struct spmi_controller_dev *ctrl_dev, }return 0 ; } -udelay (1 );/*lint !e778 !e774 !e747*/ +udelay (1 ); }dev_err (ctrl_dev->dev,"%s: timeout, status 0x%x\n" , __func__, status); -return -ETIMEDOUT ;/*lint !e438*/ -}/*lint !e715 !e529*/ +return -ETIMEDOUT ; +}static int spmi_read_cmd (struct spmi_controller *ctrl, -u8 opc,u8 sid,u16 addr,u8 *buf,size_t bc) +u8 opc,u8 sid,u16 addr,u8 *buf,size_t bc) {struct spmi_controller_dev *spmi_controller =dev_get_drvdata (&ctrl->dev);unsigned long flags;u32 cmd, data;int rc; -u32 chnl_ofst =SPMI_CHANNEL_OFFSET *spmi_controller->channel; +u32 chnl_ofst =SPMI_CHANNEL_OFFSET * spmi_controller->channel;u8 op_code, i;if (bc >SPMI_CONTROLLER_MAX_TRANS_BYTES ) {
@@ -166,27 +156,26 @@ static int spmi_read_cmd(struct spmi_controller *ctrl, }/* Check the opcode */ -if (SPMI_CMD_READ == opc) +if (opc ==SPMI_CMD_READ ) { op_code =SPMI_CMD_REG_READ ; -else if (SPMI_CMD_EXT_READ == opc) + }else if (opc ==SPMI_CMD_EXT_READ ) { op_code =SPMI_CMD_EXT_REG_READ ; -else if (SPMI_CMD_EXT_READL == opc) + }else if (opc ==SPMI_CMD_EXT_READL ) { op_code =SPMI_CMD_EXT_REG_READ_L ; -else { + }else {dev_err (spmi_controller->dev,"invalid read cmd 0x%x" , opc);return -EINVAL ; } - cmd =SPMI_APB_SPMI_CMD_EN |/*lint !e648 !e701 */ /* cmd_en */ - (op_code <<SPMI_APB_SPMI_CMD_TYPE_OFFSET ) |/*lint !e648 !e701 */ /* cmd_type */ - ((bc-1 ) <<SPMI_APB_SPMI_CMD_LENGTH_OFFSET ) |/*lint !e648 !e701 */ /* byte_cnt */ - ((sid &0xf ) <<SPMI_APB_SPMI_CMD_SLAVEID_OFFSET ) |/* slvid */ - ((addr &0xffff ) <<SPMI_APB_SPMI_CMD_ADDR_OFFSET );/* slave_addr */ + cmd =SPMI_APB_SPMI_CMD_EN | + (op_code <<SPMI_APB_SPMI_CMD_TYPE_OFFSET ) | + ((bc -1 ) <<SPMI_APB_SPMI_CMD_LENGTH_OFFSET ) | + ((sid &0xf ) <<SPMI_APB_SPMI_CMD_SLAVEID_OFFSET ) |/* slvid */ + ((addr &0xffff ) <<SPMI_APB_SPMI_CMD_ADDR_OFFSET );/* slave_addr */ -spin_lock_irqsave (&spmi_controller->lock, flags);/*lint !e550 */ - -SPMI_WRITEL (spmi_controller->dev, cmd, spmi_controller->base + chnl_ofst +SPMI_APB_SPMI_CMD_BASE_ADDR ); +spin_lock_irqsave (&spmi_controller->lock, flags); +writel (cmd, spmi_controller->base + chnl_ofst +SPMI_APB_SPMI_CMD_BASE_ADDR ); rc =spmi_controller_wait_for_done (spmi_controller, spmi_controller->base, sid, addr);if (rc)
@@ -194,39 +183,37 @@ static int spmi_read_cmd(struct spmi_controller *ctrl, i =0 ;do { -SPMI_READL (spmi_controller->dev, data, spmi_controller->base + chnl_ofst +SPMI_SLAVE_OFFSET *sid +SPMI_APB_SPMI_RDATA0_BASE_ADDR + i*SPMI_PER_DATAREG_BYTE );/*lint !e732 */ - data =Tranverse32 (data); -if ((bc - i*SPMI_PER_DATAREG_BYTE ) >>2 ) {/*lint !e702 */ + data =readl (spmi_controller->base + chnl_ofst +SPMI_SLAVE_OFFSET * sid +SPMI_APB_SPMI_RDATA0_BASE_ADDR + i *SPMI_PER_DATAREG_BYTE ); + data =bswap_32 (data); +if ((bc - i *SPMI_PER_DATAREG_BYTE ) >>2 ) {memcpy (buf, &data,sizeof (data)); buf +=sizeof (data); }else { -memcpy (buf, &data, bc%SPMI_PER_DATAREG_BYTE );/*lint !e747 */ - buf += (bc%SPMI_PER_DATAREG_BYTE ); +memcpy (buf, &data, bc %SPMI_PER_DATAREG_BYTE ); + buf += (bc %SPMI_PER_DATAREG_BYTE ); } i++; - }while (bc > i*SPMI_PER_DATAREG_BYTE ); + }while (bc > i *SPMI_PER_DATAREG_BYTE ); done:spin_unlock_irqrestore (&spmi_controller->lock, flags);if (rc)dev_err (spmi_controller->dev,"spmi read wait timeout op:0x%x sid:%d addr:0x%x bc:%ld\n" , - opc, sid, addr, bc +1 ); + opc, sid, addr, bc +1 );return rc; -}/*lint !e550 !e529*/ +} -/*lint -e438 -esym(438,*)*/ static int spmi_write_cmd (struct spmi_controller *ctrl, -u8 opc,u8 sid,u16 addr,const u8 *buf,size_t bc) +u8 opc,u8 sid,u16 addr,const u8 *buf,size_t bc) {struct spmi_controller_dev *spmi_controller =dev_get_drvdata (&ctrl->dev);unsigned long flags;u32 cmd;u32 data =0 ;int rc; -u32 chnl_ofst =SPMI_CHANNEL_OFFSET *spmi_controller->channel; +u32 chnl_ofst =SPMI_CHANNEL_OFFSET * spmi_controller->channel;u8 op_code, i; -if (bc >SPMI_CONTROLLER_MAX_TRANS_BYTES ) {dev_err (spmi_controller->dev , "spmi_controller supports 1..%d bytes per trans, but:%ld requested"
@@ -235,55 +222,55 @@ static int spmi_write_cmd(struct spmi_controller *ctrl, }/* Check the opcode */ -if (SPMI_CMD_WRITE == opc) +if (opc ==SPMI_CMD_WRITE ) { op_code =SPMI_CMD_REG_WRITE ; -else if (SPMI_CMD_EXT_WRITE == opc) + }else if (opc ==SPMI_CMD_EXT_WRITE ) { op_code =SPMI_CMD_EXT_REG_WRITE ; -else if (SPMI_CMD_EXT_WRITEL == opc) + }else if (opc ==SPMI_CMD_EXT_WRITEL ) { op_code =SPMI_CMD_EXT_REG_WRITE_L ; -else { + }else {dev_err (spmi_controller->dev,"invalid write cmd 0x%x" , opc);return -EINVAL ; } - cmd =SPMI_APB_SPMI_CMD_EN |/*lint !e648 !e701 */ /* cmd_en */ - (op_code <<SPMI_APB_SPMI_CMD_TYPE_OFFSET ) |/*lint !e648 !e701 */ /* cmd_type */ - ((bc-1 ) <<SPMI_APB_SPMI_CMD_LENGTH_OFFSET ) |/*lint !e648 !e701 */ /* byte_cnt */ - ((sid &0xf ) <<SPMI_APB_SPMI_CMD_SLAVEID_OFFSET ) |/* slvid */ - ((addr &0xffff ) <<SPMI_APB_SPMI_CMD_ADDR_OFFSET );/* slave_addr */ + cmd =SPMI_APB_SPMI_CMD_EN | + (op_code <<SPMI_APB_SPMI_CMD_TYPE_OFFSET ) | + ((bc -1 ) <<SPMI_APB_SPMI_CMD_LENGTH_OFFSET ) | + ((sid &0xf ) <<SPMI_APB_SPMI_CMD_SLAVEID_OFFSET ) |/* slvid */ + ((addr &0xffff ) <<SPMI_APB_SPMI_CMD_ADDR_OFFSET );/* slave_addr */ /* Write data to FIFOs */ -spin_lock_irqsave (&spmi_controller->lock, flags);/*lint !e550 */ +spin_lock_irqsave (&spmi_controller->lock, flags); i =0 ;do {memset (&data,0 ,sizeof (data)); -if ((bc - i*SPMI_PER_DATAREG_BYTE ) >>2 ) {/*lint !e702 */ +if ((bc - i *SPMI_PER_DATAREG_BYTE ) >>2 ) {memcpy (&data, buf,sizeof (data)); - buf +=sizeof (data); + buf +=sizeof (data); }else { -memcpy (&data, buf, bc%SPMI_PER_DATAREG_BYTE );/*lint !e747 */ - buf +=(bc%SPMI_PER_DATAREG_BYTE ); +memcpy (&data, buf, bc %SPMI_PER_DATAREG_BYTE ); + buf += (bc %SPMI_PER_DATAREG_BYTE ); } - data =Tranverse32 (data); -SPMI_WRITEL (spmi_controller->dev, data, spmi_controller->base + chnl_ofst +SPMI_APB_SPMI_WDATA0_BASE_ADDR +SPMI_PER_DATAREG_BYTE *i); + data =bswap_32 (data); +writel (data, spmi_controller->base + chnl_ofst +SPMI_APB_SPMI_WDATA0_BASE_ADDR +SPMI_PER_DATAREG_BYTE * i); i++; - }while (bc > i*SPMI_PER_DATAREG_BYTE ); + }while (bc > i *SPMI_PER_DATAREG_BYTE );/* Start the transaction */ -SPMI_WRITEL (spmi_controller->dev, cmd, spmi_controller->base + chnl_ofst +SPMI_APB_SPMI_CMD_BASE_ADDR ); +writel (cmd, spmi_controller->base + chnl_ofst +SPMI_APB_SPMI_CMD_BASE_ADDR ); rc =spmi_controller_wait_for_done (spmi_controller, spmi_controller->base, sid, addr);spin_unlock_irqrestore (&spmi_controller->lock, flags);if (rc)dev_err (spmi_controller->dev,"spmi write wait timeout op:0x%x sid:%d addr:0x%x bc:%ld\n" , - opc, sid, addr, bc); + opc, sid, addr, bc);return rc; -}/*lint !e438 !e550 !e529*/ -/*lint +e438 -esym(438,*)*/ +} +static int spmi_controller_probe (struct platform_device *pdev) {struct spmi_controller_dev *spmi_controller;
@@ -291,11 +278,11 @@ static int spmi_controller_probe(struct platform_device *pdev)struct resource *iores;int ret =0 ; -printk (KERN_INFO "HISI SPMI probe\n" ); +dev_info (&pdev->dev,"HISI SPMI probe\n" ); ctrl =spmi_controller_alloc (&pdev->dev,sizeof (*spmi_controller));if (!ctrl) {dev_err (&pdev->dev,"can not allocate spmi_controller data\n" ); -return -ENOMEM ;/*lint !e429*/ +return -ENOMEM ; } spmi_controller =spmi_controller_get_drvdata (ctrl); spmi_controller->controller = ctrl;
@@ -303,23 +290,24 @@ static int spmi_controller_probe(struct platform_device *pdev)/* NOTE: driver uses the static register mapping */ iores =platform_get_resource (pdev,IORESOURCE_MEM ,0 );if (!iores) { -dev_err (&pdev->dev,"can not get resource! \n" ); -return -EINVAL ;/*lint !e429*/ +dev_err (&pdev->dev,"can not get resource!\n" ); +return -EINVAL ; } spmi_controller->base =ioremap (iores->start,resource_size (iores));if (!spmi_controller->base) { -dev_err (&pdev->dev,"can not remap base addr! \n" ); -return -EADDRNOTAVAIL ;/*lint !e429*/ +dev_err (&pdev->dev,"can not remap base addr!\n" ); +return -EADDRNOTAVAIL ; } -dev_dbg (&pdev->dev,"spmi_add_controller base addr=0x%lx!\n" , (long unsigned int )spmi_controller->base);/*lint !e774*/ +dev_dbg (&pdev->dev,"spmi_add_controller base addr=0x%lx!\n" , + (unsigned long )spmi_controller->base);/* Get properties from the device tree */ ret =of_property_read_u32 (pdev->dev.of_node,"spmi-channel" , - &spmi_controller->channel);/*lint !e838*/ + &spmi_controller->channel);if (ret) { -dev_err (&pdev->dev,"can not get chanel \n" ); -return -ENODEV ;/*lint !e429*/ +dev_err (&pdev->dev,"can not get chanel\n" ); +return -ENODEV ; }platform_set_drvdata (pdev, spmi_controller);
@@ -342,7 +330,7 @@ static int spmi_controller_probe(struct platform_device *pdev) } err_add_controller:platform_set_drvdata (pdev,NULL ); -return ret;/*lint !e429*/ +return ret; }static int spmi_del_controller (struct platform_device *pdev)
@@ -354,10 +342,10 @@ static int spmi_del_controller(struct platform_device *pdev)return 0 ; } -static struct of_device_id spmi_controller_match_table[] = { +static const struct of_device_id spmi_controller_match_table[] = { { .compatible ="hisilicon,spmi-controller" , - },/*lint !e785*/ - {}/*lint !e785*/ + }, + {} };static struct platform_driver spmi_controller_driver = {
@@ -365,14 +353,14 @@ static struct platform_driver spmi_controller_driver = { .remove = spmi_del_controller, .driver = { .name = SPMI_CONTROLLER_NAME, - .owner = THIS_MODULE,/*lint !e64*/ + .owner = THIS_MODULE, .of_match_table = spmi_controller_match_table, - },/*lint !e785*/ -};/*lint !e785*/ -/*lint -e528 -esym(528,*)*/ + }, +}; +static int __init spmi_controller_init (void ) { -return platform_driver_register (&spmi_controller_driver);/*lint !e64*/ +return platform_driver_register (&spmi_controller_driver); }postcore_initcall (spmi_controller_init);
@@ -381,10 +369,7 @@ static void __exit spmi_controller_exit(void)platform_driver_unregister (&spmi_controller_driver); }module_exit (spmi_controller_exit); -/*lint -e753 -esym(753,*)*/ +MODULE_LICENSE ("GPL v2" ); -MODULE_VERSION ("1.0" );/*lint !e785 !e64 !e528*/ +MODULE_VERSION ("1.0" );MODULE_ALIAS ("platform:spmi_controlller" ); -/*lint -e753 +esym(753,*)*/ -/*lint -e528 +esym(528,*)*/ -
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 16/33 spmi: hisi-spmi-controller: fix the dev_foo() logic
In reply to Mauro Carvalho ChehabRight now, driver is printing some messages as:
[ 33.833026] (NULL device *): spmi_read_cmd: id:0 addr:0x17, read value: 00
This is because dev_foo() are not using a device with a name set. Change the logic for it to print it right.
--- drivers/spmi/hisi-spmi-controller.c | 41 +++++++++++++++-------------- 1 file changed, 21 insertions(+), 20 deletions(-)
drivers/spmi/hisi-spmi-controller.c +21 -20
@@ -102,7 +102,8 @@ struct spmi_controller_dev {u32 channel; }; -static int spmi_controller_wait_for_done (struct spmi_controller_dev *ctrl_dev, +static int spmi_controller_wait_for_done (struct device *dev, +struct spmi_controller_dev *ctrl_dev,void __iomem *base,u8 sid,u16 addr) {u32 status =0 ;
@@ -117,19 +118,17 @@ static int spmi_controller_wait_for_done(struct spmi_controller_dev *ctrl_dev,if (status &SPMI_APB_TRANS_DONE ) {if (status &SPMI_APB_TRANS_FAIL ) { -dev_err (ctrl_dev->dev, -"%s: transaction failed (0x%x)\n" , +dev_err (dev,"%s: transaction failed (0x%x)\n" , __func__, status);return -EIO ; } +dev_dbg (dev,"%s: status 0x%x\n" , __func__, status);return 0 ; }udelay (1 ); } -dev_err (ctrl_dev->dev, -"%s: timeout, status 0x%x\n" , - __func__, status); +dev_err (dev,"%s: timeout, status 0x%x\n" , __func__, status);return -ETIMEDOUT ; }
@@ -145,9 +144,9 @@ static int spmi_read_cmd(struct spmi_controller *ctrl,u8 op_code, i;if (bc >SPMI_CONTROLLER_MAX_TRANS_BYTES ) { -dev_err (spmi_controller->dev - ,"spmi_controller supports 1..%d bytes per trans, but:%ld requested" - ,SPMI_CONTROLLER_MAX_TRANS_BYTES , bc); +dev_err (&ctrl->dev, +"spmi_controller supports 1..%d bytes per trans, but:%ld requested" , +SPMI_CONTROLLER_MAX_TRANS_BYTES , bc);return -EINVAL ; }
@@ -159,7 +158,7 @@ static int spmi_read_cmd(struct spmi_controller *ctrl, }else if (opc ==SPMI_CMD_EXT_READL ) { op_code =SPMI_CMD_EXT_REG_READ_L ; }else { -dev_err (spmi_controller->dev,"invalid read cmd 0x%x" , opc); +dev_err (&ctrl->dev,"invalid read cmd 0x%x" , opc);return -EINVAL ; }
@@ -173,7 +172,7 @@ static int spmi_read_cmd(struct spmi_controller *ctrl,writel (cmd, spmi_controller->base + chnl_ofst +SPMI_APB_SPMI_CMD_BASE_ADDR ); - rc =spmi_controller_wait_for_done (spmi_controller, + rc =spmi_controller_wait_for_done (&ctrl->dev, spmi_controller, spmi_controller->base, sid, addr);if (rc) goto done;
@@ -195,10 +194,11 @@ static int spmi_read_cmd(struct spmi_controller *ctrl, done:spin_unlock_irqrestore (&spmi_controller->lock, flags);if (rc) -dev_err (spmi_controller->dev,"spmi read wait timeout op:0x%x sid:%d addr:0x%x bc:%ld\n" , +dev_err (&ctrl->dev, +"spmi read wait timeout op:0x%x sid:%d addr:0x%x bc:%ld\n" , opc, sid, addr, bc +1 );else -dev_dbg (spmi_controller->dev,"%s: id:%d addr:0x%x, read value: %*ph\n" , +dev_dbg (&ctrl->dev,"%s: id:%d addr:0x%x, read value: %*ph\n" , __func__, sid, addr, (int )bc, __buf);return rc;
@@ -216,9 +216,9 @@ static int spmi_write_cmd(struct spmi_controller *ctrl,u8 op_code, i;if (bc >SPMI_CONTROLLER_MAX_TRANS_BYTES ) { -dev_err (spmi_controller->dev - ,"spmi_controller supports 1..%d bytes per trans, but:%ld requested" - ,SPMI_CONTROLLER_MAX_TRANS_BYTES , bc); +dev_err (&ctrl->dev, +"spmi_controller supports 1..%d bytes per trans, but:%ld requested" , +SPMI_CONTROLLER_MAX_TRANS_BYTES , bc);return -EINVAL ; }
@@ -230,7 +230,7 @@ static int spmi_write_cmd(struct spmi_controller *ctrl, }else if (opc ==SPMI_CMD_EXT_WRITEL ) { op_code =SPMI_CMD_EXT_REG_WRITE_L ; }else { -dev_err (spmi_controller->dev,"invalid write cmd 0x%x" , opc); +dev_err (&ctrl->dev,"invalid write cmd 0x%x" , opc);return -EINVAL ; }
@@ -262,14 +262,15 @@ static int spmi_write_cmd(struct spmi_controller *ctrl,/* Start the transaction */ writel (cmd, spmi_controller->base + chnl_ofst +SPMI_APB_SPMI_CMD_BASE_ADDR ); - rc =spmi_controller_wait_for_done (spmi_controller, spmi_controller->base, sid, addr); + rc =spmi_controller_wait_for_done (&ctrl->dev, spmi_controller, + spmi_controller->base, sid, addr);spin_unlock_irqrestore (&spmi_controller->lock, flags);if (rc) -dev_err (spmi_controller->dev,"spmi write wait timeout op:0x%x sid:%d addr:0x%x bc:%ld\n" , +dev_err (&ctrl->dev,"spmi write wait timeout op:0x%x sid:%d addr:0x%x bc:%ld\n" , opc, sid, addr, bc);else -dev_dbg (spmi_controller->dev,"%s: id:%d addr:0x%x, wrote value: %*ph\n" , +dev_dbg (&ctrl->dev,"%s: id:%d addr:0x%x, wrote value: %*ph\n" , __func__, sid, addr, (int )bc, __buf);return rc;
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 15/33 mfd: Kconfig: fix a typo
In reply to Mauro Carvalho Chehabindividul -> individual
--- drivers/mfd/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/mfd/Kconfig +1 -1
@@ -493,7 +493,7 @@ config MFD_HI6421_PMIC Add support for HiSilicon Hi6421 PMIC. Hi6421 includes multi- functions, such as regulators, RTC, codec, Coulomb counter, etc. This driver includes core APIs _only_. You have to select - individul components like voltage regulators under corresponding + individual components like voltage regulators under corresponding menus in order to enable them. We communicate with the Hi6421 via memory-mapped I/O.
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 12/33 spmi: hisi-spmi-controller: add debug when values are read/write
In reply to Mauro Carvalho ChehabIt is interesting to be able to check if the driver is doing the right thing. So, add some debug macros to allow checking it.
--- drivers/spmi/hisi-spmi-controller.c | 15 ++++++++++++--- 1 file changed, 12 insertions(+), 3 deletions(-)
drivers/spmi/hisi-spmi-controller.c +12 -3
@@ -41,7 +41,6 @@#define SPMI_APB_SPMI_CMD_EN BIT(31)#define SPMI_APB_SPMI_CMD_TYPE_OFFSET 24#define SPMI_APB_SPMI_CMD_LENGTH_OFFSET 20 -#define SPMI_APB_SPMI_CMD_SLAVEID_OFFSET 16#define SPMI_APB_SPMI_CMD_ADDR_OFFSET 0
@@ -135,10 +134,11 @@ static int spmi_controller_wait_for_done(struct spmi_controller_dev *ctrl_dev, }static int spmi_read_cmd (struct spmi_controller *ctrl, -u8 opc,u8 sid,u16 addr,u8 *buf,size_t bc) +u8 opc,u8 sid,u16 addr,u8 *__buf,size_t bc) {struct spmi_controller_dev *spmi_controller =dev_get_drvdata (&ctrl->dev);unsigned long flags; +u8 *buf = __buf;u32 cmd, data;int rc;u32 chnl_ofst =SPMI_CHANNEL_OFFSET * spmi_controller->channel;
@@ -197,13 +197,18 @@ static int spmi_read_cmd(struct spmi_controller *ctrl,if (rc)dev_err (spmi_controller->dev,"spmi read wait timeout op:0x%x sid:%d addr:0x%x bc:%ld\n" , opc, sid, addr, bc +1 ); +else +dev_dbg (spmi_controller->dev,"%s: id:%d addr:0x%x, read value: %*ph\n" , + __func__, sid, addr, (int )bc, __buf); +return rc; }static int spmi_write_cmd (struct spmi_controller *ctrl, -u8 opc,u8 sid,u16 addr,const u8 *buf,size_t bc) +u8 opc,u8 sid,u16 addr,const u8 *__buf,size_t bc) {struct spmi_controller_dev *spmi_controller =dev_get_drvdata (&ctrl->dev); +const u8 *buf = __buf;unsigned long flags;u32 cmd, data;int rc;
@@ -263,6 +268,9 @@ static int spmi_write_cmd(struct spmi_controller *ctrl,if (rc)dev_err (spmi_controller->dev,"spmi write wait timeout op:0x%x sid:%d addr:0x%x bc:%ld\n" , opc, sid, addr, bc); +else +dev_dbg (spmi_controller->dev,"%s: id:%d addr:0x%x, wrote value: %*ph\n" , + __func__, sid, addr, (int )bc, __buf);return rc; }
@@ -275,6 +283,7 @@ static int spmi_controller_probe(struct platform_device *pdev)int ret =0 ;dev_info (&pdev->dev,"HISI SPMI probe\n" ); + ctrl =spmi_controller_alloc (&pdev->dev,sizeof (*spmi_controller));if (!ctrl) {dev_err (&pdev->dev,"can not allocate spmi_controller data\n" );
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 9/33 spmi: hisi-spmi-controller: fix a typo
In reply to Mauro Carvalho Chehabchanel -> channel
--- drivers/spmi/hisi-spmi-controller.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/spmi/hisi-spmi-controller.c +1 -1
@@ -306,7 +306,7 @@ static int spmi_controller_probe(struct platform_device *pdev) ret =of_property_read_u32 (pdev->dev.of_node,"spmi-channel" , &spmi_controller->channel);if (ret) { -dev_err (&pdev->dev,"can not get chanel\n" ); +dev_err (&pdev->dev,"can not get channel\n" );return -ENODEV ; }
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 8/33 spmi: hisi-spmi-controller: fix it to probe successfully
In reply to Mauro Carvalho ChehabAdd a MODULE_DEVICE_TABLE() to the driver.
Also, the current logic calls platform_set_drvdata(pdev, NULL) if the driver succeeds loading.
While here, remove the .owner, as it is not needed upstream anymore.
--- drivers/spmi/hisi-spmi-controller.c | 11 +++++++---- 1 file changed, 7 insertions(+), 4 deletions(-)
drivers/spmi/hisi-spmi-controller.c +7 -4
@@ -324,11 +324,14 @@ static int spmi_controller_probe(struct platform_device *pdev) ctrl->write_cmd = spmi_write_cmd; ret =spmi_controller_add (ctrl); -if (ret) { -dev_err (&pdev->dev,"spmi_add_controller failed!\n" ); +if (ret) goto err_add_controller; - } + +dev_info (&pdev->dev,"spmi_add_controller initialized\n" ); +return 0 ; + err_add_controller: +dev_err (&pdev->dev,"spmi_add_controller failed!\n" );platform_set_drvdata (pdev,NULL );return ret; }
@@ -347,13 +350,13 @@ static const struct of_device_id spmi_controller_match_table[] = { }, {} }; +MODULE_DEVICE_TABLE (of, spmi_controller_match_table);static struct platform_driver spmi_controller_driver = { .probe = spmi_controller_probe, .remove = spmi_del_controller, .driver = { .name =SPMI_CONTROLLER_NAME , - .owner =THIS_MODULE , .of_match_table = spmi_controller_match_table, }, };
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 14/33 spmi: add hisi-spmi-controller to the building system
In reply to Mauro Carvalho ChehabNow that the driver was ported to upstream, add it as a SPMI controller.
--- drivers/spmi/Kconfig | 9 +++++++++ drivers/spmi/Makefile | 2 ++ 2 files changed, 11 insertions(+)
drivers/spmi/Kconfig +9 -0
@@ -25,4 +25,13 @@ config SPMI_MSM_PMIC_ARB This is required for communicating with Qualcomm PMICs and other devices that have the SPMI interface. +config SPMI_HISI3670 + tristate "Hisilicon 3670 SPMI Controller" + select IRQ_DOMAIN_HIERARCHY + depends on HAS_IOMEM + help + If you say yes to this option, support will be included for the + built-in SPMI PMIC Arbiter interface on Hisilicon 3670 + processors. + endif
drivers/spmi/Makefile +2 -0
@@ -5,3 +5,5 @@ obj-$(CONFIG_SPMI) += spmi.o obj-$(CONFIG_SPMI_MSM_PMIC_ARB) += spmi-pmic-arb.o + +obj-$(CONFIG_SPMI_HISI3670) += hisi-spmi-controller.o
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 11/33 spmi: hisi-spmi-controller: use le32 macros where needed
In reply to Mauro Carvalho ChehabInstead of manually using bswap_32(), just use the le32 macros.
--- drivers/spmi/hisi-spmi-controller.c | 20 +++++++------------- 1 file changed, 7 insertions(+), 13 deletions(-)
drivers/spmi/hisi-spmi-controller.c +7 -13
@@ -11,7 +11,6 @@#include <linux/module.h> #include <linux/seq_file.h> #include <linux/spmi.h> -#include <linux/spmi.h> #define SPMI_CONTROLLER_NAME "spmi_controller"
@@ -43,11 +42,6 @@#define SPMI_APB_SPMI_CMD_TYPE_OFFSET 24#define SPMI_APB_SPMI_CMD_LENGTH_OFFSET 20 -#define bswap_32 (X ) \ - ((((u32)(X) & 0xff000000) >> 24) | \ - (((u32)(X) & 0x00ff0000) >> 8) | \ - (((u32)(X) & 0x0000ff00) << 8) | \ - (((u32)(X) & 0x000000ff) << 24))#define SPMI_APB_SPMI_CMD_SLAVEID_OFFSET 16#define SPMI_APB_SPMI_CMD_ADDR_OFFSET 0
@@ -179,14 +173,15 @@ static int spmi_read_cmd(struct spmi_controller *ctrl,writel (cmd, spmi_controller->base + chnl_ofst +SPMI_APB_SPMI_CMD_BASE_ADDR ); - rc =spmi_controller_wait_for_done (spmi_controller, spmi_controller->base, sid, addr); + rc =spmi_controller_wait_for_done (spmi_controller, + spmi_controller->base, sid, addr);if (rc) goto done; i =0 ; do { data = readl(spmi_controller->base + chnl_ofst + SPMI_SLAVE_OFFSET * sid + SPMI_APB_SPMI_RDATA0_BASE_ADDR + i * SPMI_PER_DATAREG_BYTE); - data = bswap_32(data); + data = be32_to_cpu((__be32)data); if ((bc - i * SPMI_PER_DATAREG_BYTE) >> 2) { memcpy(buf, &data, sizeof(data)); buf += sizeof(data);
@@ -210,8 +205,7 @@ static int spmi_write_cmd(struct spmi_controller *ctrl, {struct spmi_controller_dev *spmi_controller =dev_get_drvdata (&ctrl->dev);unsigned long flags; -u32 cmd; -u32 data =0 ; +u32 cmd, data;int rc;u32 chnl_ofst =SPMI_CHANNEL_OFFSET * spmi_controller->channel;u8 op_code, i;
@@ -246,7 +240,7 @@ static int spmi_write_cmd(struct spmi_controller *ctrl, i =0 ; do { - memset(&data, 0, sizeof(data)); + data = 0; if ((bc - i * SPMI_PER_DATAREG_BYTE) >> 2) { memcpy(&data, buf, sizeof(data)); buf += sizeof(data);
@@ -255,8 +249,8 @@ static int spmi_write_cmd(struct spmi_controller *ctrl, buf += (bc %SPMI_PER_DATAREG_BYTE ); } - data =bswap_32 (data); -writel (data, spmi_controller->base + chnl_ofst +SPMI_APB_SPMI_WDATA0_BASE_ADDR +SPMI_PER_DATAREG_BYTE * i); +writel ((u32 )cpu_to_be32 (data), + spmi_controller->base + chnl_ofst +SPMI_APB_SPMI_WDATA0_BASE_ADDR +SPMI_PER_DATAREG_BYTE * i); i++; }while (bc > i *SPMI_PER_DATAREG_BYTE );
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 6/33 mfd: hisi_pmic_spmi: deal with non-static functions
In reply to Mauro Carvalho ChehabSeveral functions aren't used outside the mfd driver. So, either remove or make them static.
--- drivers/mfd/hisi_pmic_spmi.c | 147 ++++++----------------------------- 1 file changed, 24 insertions(+), 123 deletions(-)
drivers/mfd/hisi_pmic_spmi.c +24 -123
@@ -73,21 +73,21 @@ u32 hisi_pmic_read(struct hisi_pmic *pmic, int reg)u8 read_value =0 ;struct spmi_device *pdev; -if (NULL == g_pmic) { -pr_err (" g_pmic is NULL\n" ); +if (!g_pmic) { +pr_err ("%s: g_pmic is NULL\n" , __func__);return 0 ; } pdev =to_spmi_device (g_pmic->dev); -if (NULL == pdev) { -pr_err ("%s:pdev get failed!\n" , __func__); +if (!pdev) { +pr_err ("%s: pdev get failed!\n" , __func__);return 0 ; } ret =spmi_ext_register_readl (pdev, reg, (unsigned char *)&read_value,1 );/*lint !e734 !e732 */ if (ret) { -pr_err ("%s:spmi_ext_register_readl failed!\n" , __func__); -return ret; +pr_err ("%s: spmi_ext_register_readl failed!\n" , __func__); +return 0 ; }return (u32 )read_value; }
@@ -98,34 +98,32 @@ void hisi_pmic_write(struct hisi_pmic *pmic, int reg, u32 val)u32 ret;struct spmi_device *pdev; -if (NULL == g_pmic) { -pr_err (" g_pmic is NULL\n" ); +if (!g_pmic) { +pr_err ("%s: g_pmic is NULL\n" , __func__);return ; } pdev =to_spmi_device (g_pmic->dev); -if (NULL == pdev) { -pr_err ("%s:pdev get failed!\n" , __func__); +if (!pdev) { +pr_err ("%s: pdev get failed!\n" , __func__);return ; } ret =spmi_ext_register_writel (pdev, reg, (unsigned char *)&val,1 );/*lint !e734 !e732 */ if (ret) { -pr_err ("%s:spmi_ext_register_writel failed!\n" , __func__); -return ; +pr_err ("%s: spmi_ext_register_writel failed!\n" , __func__); +return ; } }EXPORT_SYMBOL (hisi_pmic_write); - -void hisi_pmic_rmw (struct hisi_pmic *pmic,int reg, -u32 mask,u32 bits) +void hisi_pmic_rmw (struct hisi_pmic *pmic,int reg,u32 mask,u32 bits) {u32 data;unsigned long flags; -if (NULL == g_pmic) { -pr_err (" g_pmic is NULL\n" ); +if (!g_pmic) { +pr_err ("%s: g_pmic is NULL\n" , __func__);return ; }
@@ -137,75 +135,6 @@ void hisi_pmic_rmw(struct hisi_pmic *pmic, int reg, }EXPORT_SYMBOL (hisi_pmic_rmw); -unsigned int hisi_pmic_reg_read (int addr) -{ -return (unsigned int )hisi_pmic_read (g_pmic, addr); -} -EXPORT_SYMBOL (hisi_pmic_reg_read); - -void hisi_pmic_reg_write (int addr,int val) -{ -hisi_pmic_write (g_pmic, addr, val); -} -EXPORT_SYMBOL (hisi_pmic_reg_write); - -void hisi_pmic_reg_write_lock (int addr,int val) -{ -unsigned long flags; - -if (NULL == g_pmic) { -pr_err (" g_pmic is NULL\n" ); -return ; - } - -spin_lock_irqsave (&g_pmic->lock, flags); -hisi_pmic_write (g_pmic, g_pmic->normal_lock.addr, g_pmic->normal_lock.val); -hisi_pmic_write (g_pmic, g_pmic->debug_lock.addr, g_pmic->debug_lock.val); -hisi_pmic_write (g_pmic, addr, val); -hisi_pmic_write (g_pmic, g_pmic->normal_lock.addr,0 ); -hisi_pmic_write (g_pmic, g_pmic->debug_lock.addr,0 ); -spin_unlock_irqrestore (&g_pmic->lock, flags); -} - -int hisi_pmic_array_read (int addr,char *buff,unsigned int len) -{ -unsigned int i; - -if ((len >32 ) || (NULL == buff)) { -return -EINVAL ; - } - -/* -* Here is a bug in the pmu die. -* the coul driver will read 4 bytes, -* but the ssi bus only read 1 byte, and the pmu die -* will make sampling 1/10669us about vol cur,so the driver -* read the data is not the same sampling -*/ -for (i =0 ; i < len; i++) - { - *(buff + i) =hisi_pmic_reg_read (addr+i); - } - -return 0 ; -} - -int hisi_pmic_array_write (int addr,char *buff,unsigned int len) -{ -unsigned int i; - -if ((len >32 ) || (NULL == buff)) { -return -EINVAL ; - } - -for (i =0 ; i < len; i++) - { -hisi_pmic_reg_write (addr+i, *(buff + i)); - } - -return 0 ; -} -static irqreturn_t hisi_irq_handler (int irq,void *data) {struct hisi_pmic *pmic = (struct hisi_pmic *)data;
@@ -213,13 +142,13 @@ static irqreturn_t hisi_irq_handler(int irq, void *data)int i, offset;for (i =0 ; i < pmic->irqarray; i++) { - pending =hisi_pmic_reg_read ((i + pmic->irq_addr.start_addr)); + pending =hisi_pmic_read (g_pmic, (i + pmic->irq_addr.start_addr)); pending &=HISI_MASK_FIELD ;if (pending !=0 ) {pr_info ("pending[%d]=0x%lx\n\r" , i, pending); } -hisi_pmic_reg_write ((i + pmic->irq_addr.start_addr), pending); +hisi_pmic_write (g_pmic, (i + pmic->irq_addr.start_addr), pending);/*solve powerkey order*/ if ((HISI_IRQ_KEY_NUM == i) && ((pending &HISI_IRQ_KEY_VALUE ) ==HISI_IRQ_KEY_VALUE )) {
@@ -237,13 +166,13 @@ static irqreturn_t hisi_irq_handler(int irq, void *data)/*Handle the second group irq if analysis the second group irq from dtsi*/ if (1 == g_extinterrupt_flag){for (i =0 ; i < pmic->irqarray1; i++) { - pending =hisi_pmic_reg_read ((i + pmic->irq_addr1.start_addr)); + pending =hisi_pmic_read (g_pmic, (i + pmic->irq_addr1.start_addr)); pending &=HISI_MASK_FIELD ;if (pending !=0 ) {pr_info ("pending[%d]=0x%lx\n\r" , i, pending); } -hisi_pmic_reg_write ((i + pmic->irq_addr1.start_addr), pending); +hisi_pmic_write (g_pmic, (i + pmic->irq_addr1.start_addr), pending);if (pending) {for_each_set_bit (offset, &pending,HISI_BITS )
@@ -276,9 +205,9 @@ static void hisi_irq_mask(struct irq_data *d) offset += pmic->irq_mask_addr.start_addr; }spin_lock_irqsave (&g_pmic->lock, flags); - data =hisi_pmic_reg_read (offset); + data =hisi_pmic_read (g_pmic, offset); data |= (1 << (irqd_to_hwirq (d) &0x07 )); -hisi_pmic_reg_write (offset, data); +hisi_pmic_write (g_pmic, offset, data);spin_unlock_irqrestore (&g_pmic->lock, flags); }
@@ -303,9 +232,9 @@ static void hisi_irq_unmask(struct irq_data *d) offset += pmic->irq_mask_addr.start_addr; }spin_lock_irqsave (&g_pmic->lock, flags); - data =hisi_pmic_reg_read (offset); - data &= ~(1 << (irqd_to_hwirq (d) &0x07 ));/*lint !e502 */ -hisi_pmic_reg_write (offset, data); + data =hisi_pmic_read (g_pmic, offset); + data &= ~(1 << (irqd_to_hwirq (d) &0x07 )); +hisi_pmic_write (g_pmic, offset, data);spin_unlock_irqrestore (&g_pmic->lock, flags); }
@@ -452,34 +381,6 @@ static int get_pmic_device_tree_data1(struct device_node *np, struct hisi_pmic *return ret; }/*lint -restore*/ -int hisi_get_pmic_irq_byname (unsigned int pmic_irq_list) -{ -if (NULL == g_pmic ) { -pr_err ("[%s]g_pmic is NULL\n" , __func__); -return -1 ; - } - -if (pmic_irq_list > (unsigned int )g_pmic->irqnum) { -pr_err ("[%s]input pmic irq number is error.\n" , __func__); -return -1 ; - } -pr_info ("%s:g_pmic->irqs[%d]=%d\n" , __func__, pmic_irq_list, g_pmic->irqs[pmic_irq_list]); -return (int )g_pmic->irqs[pmic_irq_list]; -} -EXPORT_SYMBOL (hisi_get_pmic_irq_byname); - -int hisi_pmic_get_vbus_status (void ) -{ -if (0 == g_pmic_vbus.addr) -return -1 ; - -if (hisi_pmic_reg_read (g_pmic_vbus.addr) &BIT (g_pmic_vbus.bit)) -return 1 ; - -return 0 ; -} -EXPORT_SYMBOL (hisi_pmic_get_vbus_status); -static void hisi_pmic_irq_prc (struct hisi_pmic *pmic) {int i;
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerPATCH 7/33 mfd: hisi_pmic_spmi: get rid of the static vars
In reply to Mauro Carvalho ChehabThere are several static vars inside this driver.
Get rid of them.
--- drivers/mfd/hisi_pmic_spmi.c | 100 +++++++++++----------------------- include/linux/mfd/hisi_pmic.h | 2 + 2 files changed, 34 insertions(+), 68 deletions(-)
drivers/mfd/hisi_pmic_spmi.c +32 -68
@@ -52,10 +52,7 @@/*define the first group interrupt register number*/ #define HISI_PMIC_FIRST_GROUP_INT_NUM 2 -static struct bit_info g_pmic_vbus = {0 }; -static struct hisi_pmic *g_pmic; -static unsigned int g_extinterrupt_flag =0 ; -static struct of_device_id of_hisi_pmic_match_tbl[] = { +static const struct of_device_id of_hisi_pmic_match_tbl[] = { { .compatible ="hisilicon-hisi-pmic-spmi" , },
@@ -73,12 +70,7 @@ u32 hisi_pmic_read(struct hisi_pmic *pmic, int reg)u8 read_value =0 ;struct spmi_device *pdev; -if (!g_pmic) { -pr_err ("%s: g_pmic is NULL\n" , __func__); -return 0 ; - } - - pdev =to_spmi_device (g_pmic->dev); + pdev =to_spmi_device (pmic->dev);if (!pdev) {pr_err ("%s: pdev get failed!\n" , __func__);return 0 ;
@@ -98,12 +90,7 @@ void hisi_pmic_write(struct hisi_pmic *pmic, int reg, u32 val)u32 ret;struct spmi_device *pdev; -if (!g_pmic) { -pr_err ("%s: g_pmic is NULL\n" , __func__); -return ; - } - - pdev =to_spmi_device (g_pmic->dev); + pdev =to_spmi_device (pmic->dev);if (!pdev) {pr_err ("%s: pdev get failed!\n" , __func__);return ;
@@ -122,16 +109,11 @@ void hisi_pmic_rmw(struct hisi_pmic *pmic, int reg, u32 mask, u32 bits)u32 data;unsigned long flags; -if (!g_pmic) { -pr_err ("%s: g_pmic is NULL\n" , __func__); -return ; - } - -spin_lock_irqsave (&g_pmic->lock, flags); +spin_lock_irqsave (&pmic->lock, flags); data =hisi_pmic_read (pmic, reg) & ~mask; data |= mask & bits;hisi_pmic_write (pmic, reg, data); -spin_unlock_irqrestore (&g_pmic->lock, flags); +spin_unlock_irqrestore (&pmic->lock, flags); }EXPORT_SYMBOL (hisi_pmic_rmw);
@@ -142,13 +124,13 @@ static irqreturn_t hisi_irq_handler(int irq, void *data)int i, offset;for (i =0 ; i < pmic->irqarray; i++) { - pending =hisi_pmic_read (g_pmic, (i + pmic->irq_addr.start_addr)); + pending =hisi_pmic_read (pmic, (i + pmic->irq_addr.start_addr)); pending &=HISI_MASK_FIELD ;if (pending !=0 ) {pr_info ("pending[%d]=0x%lx\n\r" , i, pending); } -hisi_pmic_write (g_pmic, (i + pmic->irq_addr.start_addr), pending); +hisi_pmic_write (pmic, (i + pmic->irq_addr.start_addr), pending);/*solve powerkey order*/ if ((HISI_IRQ_KEY_NUM == i) && ((pending &HISI_IRQ_KEY_VALUE ) ==HISI_IRQ_KEY_VALUE )) {
@@ -164,15 +146,15 @@ static irqreturn_t hisi_irq_handler(int irq, void *data) }/*Handle the second group irq if analysis the second group irq from dtsi*/ -if (1 == g_extinterrupt_flag){ +if (pmic->g_extinterrupt_flag ==1 ) {for (i =0 ; i < pmic->irqarray1; i++) { - pending =hisi_pmic_read (g_pmic, (i + pmic->irq_addr1.start_addr)); + pending =hisi_pmic_read (pmic, (i + pmic->irq_addr1.start_addr)); pending &=HISI_MASK_FIELD ;if (pending !=0 ) {pr_info ("pending[%d]=0x%lx\n\r" , i, pending); } -hisi_pmic_write (g_pmic, (i + pmic->irq_addr1.start_addr), pending); +hisi_pmic_write (pmic, (i + pmic->irq_addr1.start_addr), pending);if (pending) {for_each_set_bit (offset, &pending,HISI_BITS )
@@ -190,25 +172,20 @@ static void hisi_irq_mask(struct irq_data *d)u32 data, offset;unsigned long flags; -if (NULL == g_pmic) { -pr_err (" g_pmic is NULL\n" ); -return ; - } - offset = (irqd_to_hwirq (d) >>3 ); -if (1 ==g_extinterrupt_flag){ -if ( offset <HISI_PMIC_FIRST_GROUP_INT_NUM ) +if (pmic->g_extinterrupt_flag ==1 ) { +if (offset <HISI_PMIC_FIRST_GROUP_INT_NUM ) offset += pmic->irq_mask_addr.start_addr;else /*Change addr when irq num larger than 16 because interrupt addr is nonsequence*/ offset = offset+(pmic->irq_mask_addr1.start_addr)-HISI_PMIC_FIRST_GROUP_INT_NUM ; }else { offset += pmic->irq_mask_addr.start_addr; } -spin_lock_irqsave (&g_pmic->lock, flags); - data =hisi_pmic_read (g_pmic, offset); +spin_lock_irqsave (&pmic->lock, flags); + data =hisi_pmic_read (pmic, offset); data |= (1 << (irqd_to_hwirq (d) &0x07 )); -hisi_pmic_write (g_pmic, offset, data); -spin_unlock_irqrestore (&g_pmic->lock, flags); +hisi_pmic_write (pmic, offset, data); +spin_unlock_irqrestore (&pmic->lock, flags); }static void hisi_irq_unmask (struct irq_data *d)
@@ -217,25 +194,20 @@ static void hisi_irq_unmask(struct irq_data *d)u32 data, offset;unsigned long flags; -if (NULL == g_pmic) { -pr_err (" g_pmic is NULL\n" ); -return ; - } - offset = (irqd_to_hwirq (d) >>3 ); -if (1 ==g_extinterrupt_flag){ -if ( offset <HISI_PMIC_FIRST_GROUP_INT_NUM ) +if (pmic->g_extinterrupt_flag ==1 ) { +if (offset <HISI_PMIC_FIRST_GROUP_INT_NUM ) offset += pmic->irq_mask_addr.start_addr;else offset = offset+(pmic->irq_mask_addr1.start_addr)-HISI_PMIC_FIRST_GROUP_INT_NUM ; }else { offset += pmic->irq_mask_addr.start_addr; } -spin_lock_irqsave (&g_pmic->lock, flags); - data =hisi_pmic_read (g_pmic, offset); +spin_lock_irqsave (&pmic->lock, flags); + data =hisi_pmic_read (pmic, offset); data &= ~(1 << (irqd_to_hwirq (d) &0x07 )); -hisi_pmic_write (g_pmic, offset, data); -spin_unlock_irqrestore (&g_pmic->lock, flags); +hisi_pmic_write (pmic, offset, data); +spin_unlock_irqrestore (&pmic->lock, flags); }static struct irq_chip hisi_pmu_irqchip = {
@@ -305,14 +277,6 @@ static int get_pmic_device_tree_data(struct device_node *np, struct hisi_pmic *preturn ret; } - ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-vbus" , - (u32 *)&g_pmic_vbus,2 ); -if (ret) { -pr_err ("no hisilicon,hisi-pmic-vbus property\n" ); - ret = -ENODEV ; -return ret; - } -/*pmic lock*/ ret =of_property_read_u32_array (np,"hisilicon,hisi-pmic-lock" , (int *)&pmic->normal_lock,2 );
@@ -377,7 +341,7 @@ static int get_pmic_device_tree_data1(struct device_node *np, struct hisi_pmic *return ret; } - g_extinterrupt_flag =1 ; + pmic->g_extinterrupt_flag =1 ;return ret; }/*lint -restore*/
@@ -399,13 +363,14 @@ static void hisi_pmic_irq_prc(struct hisi_pmic *pmic)static void hisi_pmic_irq1_prc (struct hisi_pmic *pmic) {int i; -if (1 == g_extinterrupt_flag){ -for (i =0 ; i < pmic->irq_mask_addr1.array; i++) { +unsigned int pending1; + +if (pmic->g_extinterrupt_flag ==1 ) { +for (i =0 ; i < pmic->irq_mask_addr1.array; i++)hisi_pmic_write (pmic, pmic->irq_mask_addr1.start_addr + i,HISI_MASK_STATE ); - }for (i =0 ; i < pmic->irq_addr1.array; i++) { -unsigned int pending1 =hisi_pmic_read (pmic, pmic->irq_addr1.start_addr + i); + pending1 =hisi_pmic_read (pmic, pmic->irq_addr1.start_addr + i);pr_debug ("PMU IRQ address1 value:irq[0x%x] = 0x%x\n" , pmic->irq_addr1.start_addr + i, pending1);hisi_pmic_write (pmic, pmic->irq_addr1.start_addr + i,HISI_MASK_STATE ); }
@@ -446,11 +411,11 @@ static int hisi_pmic_probe(struct spmi_device *pdev)spin_lock_init (&pmic->lock); pmic->dev = dev; - g_pmic = pmic; - ret =of_property_read_u32_array (np,"hisilicon,pmic_fpga_flag" , &fpga_flag,1 ); -if (ret) { + ret =of_property_read_u32_array (np,"hisilicon,pmic_fpga_flag" , + &fpga_flag,1 ); +if (ret)pr_err ("no hisilicon,pmic_fpga_flag property set\n" ); - } +if (PMIC_FPGA_FLAG == fpga_flag) { goto after_irq_register; }
@@ -521,7 +486,6 @@ static int hisi_pmic_probe(struct spmi_device *pdev) irq_domain: irq_malloc:gpio_free (pmic->gpio); - g_pmic =NULL ;return ret; }
include/linux/mfd/hisi_pmic.h +2 -0
@@ -71,6 +71,8 @@ struct hisi_pmic {struct irq_info irq_addr1;struct write_lock normal_lock;struct write_lock debug_lock; + +unsigned int g_extinterrupt_flag; };u32 hisi_pmic_read (struct hisi_pmic *pmic,int reg);
Signature · 1 line
2.26.2
Mauro Carvalho Chehab
maintainerEm Tue, 11 Aug 2020 17:41:26 +0200
Mauro Carvalho Chehab <[email protected]> escreveu:
Quoted 12 lines
The Hikey 970 board uses a different PMIC than the one found on Hikey 960.
This PMIC uses a SPMI board.
This patch series backport the OOT drivers from the Linaro's official tree for this board:
https://github.com/96boards-hikey/linux/tree/hikey970-v4.9Porting them to upstream, cleaning up coding style issues, solving driver probing order and adding DT documentation.
Quoted 8 lines
I opted to not fold all patches into a single one, in order to:
- Preserve the authorship of the original authors;
- Keep a history of changes.As this could be harder for people to review, I'll be replying to patch 00/32 with all patches folded. This should help reviewers to see the current code after the entire series is applied.
As promised, it follows the diff from this entire patch series.
Feel free to review either on the top of this e-mail or on the individual patches.
Thanks!
Mauro
Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml | 175 ++++++++++++++++++++++++++++++++++++++ Documentation/devicetree/bindings/spmi/hisilicon,hisi-spmi-controller.yaml | 54 ++++++++++++ MAINTAINERS | 8 ++ arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts | 16 +--- arch/arm64/boot/dts/hisilicon/hikey970-pmic.dtsi | 200 ++++++++++++++++++++++++++++++++++++++++++++ drivers/mfd/Kconfig | 17 +++- drivers/mfd/Makefile | 1 + drivers/mfd/hi6421-spmi-pmic.c | 399 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ drivers/regulator/Kconfig | 8 ++ drivers/regulator/Makefile | 1 + drivers/regulator/hi6421v600-regulator.c | 493 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ drivers/spmi/Kconfig | 9 ++ drivers/spmi/Makefile | 2 + drivers/spmi/hisi-spmi-controller.c | 384 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ drivers/spmi/spmi.c | 10 +-- include/linux/mfd/hi6421-spmi-pmic.h | 67 +++++++++++++++ 16 files changed, 1826 insertions(+), 18 deletions(-)
Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml new file +175 -0
@@ -0,0 +1,175 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/hisilicon,hi6421v600-regulator.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: HiSilicon 6421v600 SPMI PMIC + +maintainers: + - Mauro Carvalho Chehab <[email protected]> + +description: | + HiSilicon 6421v600 uses a MIPI System Power Management (SPMI) bus in order + to provide interrupts and power supply. + + The GPIO and interrupt settings are represented as part of the top-level PMIC + node. + + The SPMI controller part is provided by + Documentation/devicetree/bindings/spmi/hisilicon,hisi-spmi-controller.yaml. + +properties: + $nodename: + pattern: "pmic@[0-9a-f]" + + compatible: + const: hisilicon,hi6421-spmi-pmic + + reg: + maxItems: 1 + + spmi-channel: + description: number of the SPMI channel where the PMIC is connected + + '#interrupt-cells': + const: 2 + + interrupt-controller: + description: + Identify that the PMIC is capable of behaving as an interrupt controller. + + gpios: + maxItems: 1 + + irq-num: + description: Interrupt request number + + 'irq-array': + description: Interrupt request array + + 'irq-mask-addr': + description: Address for the interrupt request mask + + 'irq-addr': + description: Address for the interrupt request + + regulators: + type: object + + properties: + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + patternProperties: + '^ldo@[0-9]+$': + type: object + + $ref: "/schemas/regulator/regulator.yaml#" + + properties: + reg: + description: Enable register. + + vsel-reg: + description: Voltage selector register. + + enable-mask: + description: Bitmask used to enable the regulator. + +# voltage-table: +# description: Table with the selector items for the voltage regulator. +# minItems: 2 +# maxItems: 16 + + off-on-delay-us: + description: Time required for changing state to enabled in microseconds. + + startup-delay-us: + description: Startup time in microseconds. + + idle-mode-mask: + description: Bitmask used to put the regulator on idle mode. + + eco-microamp: + description: Maximum current while on idle mode. + + required: + - reg + - vsel-reg + - enable-mask + - voltage-table + - off-on-delay-us + - startup-delay-us + +required: + - compatible + - reg + - spmi-channel + - regulators + +examples: + - | + pmic: pmic@0 { + compatible = "hisilicon,hi6421-spmi-pmic"; + slave_id = <0>; + reg = <0 0>; + + #interrupt-cells = <2>; + interrupt-controller; + gpios = <&gpio28 0 0>; + irq-num = <16>; + irq-array = <2>; + irq-mask-addr = <0x202 2>; + irq-addr = <0x212 2>; + + regulators { + ldo3: ldo3@16 { + reg = <0x16>; + vsel-reg = <0x51>; + + regulator-name = "ldo3"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <2000000>; + regulator-boot-on; + + enable-mask = <0x01>; + + voltage-table = <1500000>, <1550000>, + <1600000>, <1650000>, + <1700000>, <1725000>, + <1750000>, <1775000>, + <1800000>, <1825000>, + <1850000>, <1875000>, + <1900000>, <1925000>, + <1950000>, <2000000>; + off-on-delay-us = <20000>; + startup-delay-us = <120>; + }; + + ldo4: ldo4@17 { /* 40 PIN */ + reg = <0x17>; + vsel-reg = <0x52>; + + regulator-name = "ldo4"; + regulator-min-microvolt = <1725000>; + regulator-max-microvolt = <1900000>; + regulator-boot-on; + + enable-mask = <0x01>; + idle-mode-mask = <0x10>; + eco-microamp = <10000>; + + hi6421-vsel = <0x52 0x07>; + voltage-table = <1725000>, <1750000>, + <1775000>, <1800000>, + <1825000>, <1850000>, + <1875000>, <1900000>; + off-on-delay-us = <20000>; + startup-delay-us = <120>; + }; + }; + };
Documentation/devicetree/bindings/spmi/hisilicon,hisi-spmi-controller.yaml new file +54 -0
54 lines not on this page · raw message
MAINTAINERS +8 -0
@@ -7736,6 +7736,14 @@ F: include/linux/hippidevice.h F: include/uapi/linux/if_hippi.h F: net/802/hippi.c +HISILICON 6421v600 SPMI PMIC DRIVER +M: Mauro Carvalho Chehab <[email protected]> +L: [email protected] +S: Maintained +F: drivers/mfd/hi6421-spmi-pmic.c +F: drivers/regulator/hi6421v600-regulator.c +F: drivers/spmi/spmi.c + HISILICON DMA DRIVER M: Zhou Wang <[email protected]> L: [email protected]
arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts +4 -12
@@ -12,6 +12,7 @@ #include "hi3670.dtsi" #include "hikey970-pinctrl.dtsi" +#include "hikey970-pmic.dtsi" / { model = "HiKey970";
@@ -39,7 +40,7 @@ memory@0 { reg = <0x0 0x0 0x0 0x0>; }; - sd_1v8: regulator-1v8 { + fixed_1v8: regulator-1v8 { compatible = "regulator-fixed"; regulator-name = "fixed-1.8V"; regulator-min-microvolt = <1800000>;
@@ -47,15 +48,6 @@ sd_1v8: regulator-1v8 { regulator-always-on; }; - sd_3v3: regulator-3v3 { - compatible = "regulator-fixed"; - regulator-name = "fixed-3.3V"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-boot-on; - regulator-always-on; - }; - wlan_en: wlan-en-1-8v { compatible = "regulator-fixed"; regulator-name = "wlan-en-regulator";
@@ -402,8 +394,8 @@ &dwmmc1 { pinctrl-0 = <&sd_pmx_func &sd_clk_cfg_func &sd_cfg_func>; - vmmc-supply = <&sd_3v3>; - vqmmc-supply = <&sd_1v8>; + vmmc-supply = <&ldo16>; + vqmmc-supply = <&ldo9>; status = "okay"; };
arch/arm64/boot/dts/hisilicon/hikey970-pmic.dtsi new file +200 -0
200 lines not on this page · raw message
drivers/mfd/Kconfig +16 -1
@@ -493,10 +493,25 @@ config MFD_HI6421_PMIC Add support for HiSilicon Hi6421 PMIC. Hi6421 includes multi- functions, such as regulators, RTC, codec, Coulomb counter, etc. This driver includes core APIs _only_. You have to select - individul components like voltage regulators under corresponding + individual components like voltage regulators under corresponding menus in order to enable them. We communicate with the Hi6421 via memory-mapped I/O. +config MFD_HI6421_SPMI + tristate "HiSilicon Hi6421v600 SPMI PMU/Codec IC" + depends on OF + select MFD_CORE + select REGMAP_MMIO + help + Add support for HiSilicon Hi6421v600 SPMI PMIC. Hi6421 includes + multi-functions, such as regulators, RTC, codec, Coulomb counter, + etc. + + This driver includes core APIs _only_. You have to select + individual components like voltage regulators under corresponding + menus in order to enable them. + We communicate with the Hi6421v600 via a SPMI bus. + config MFD_HI655X_PMIC tristate "HiSilicon Hi655X series PMU/Codec IC" depends on ARCH_HISI || COMPILE_TEST
drivers/mfd/Makefile +1 -0
@@ -233,6 +233,7 @@ obj-$(CONFIG_MFD_IPAQ_MICRO) += ipaq-micro.o obj-$(CONFIG_MFD_IQS62X) += iqs62x.o obj-$(CONFIG_MFD_MENF21BMC) += menf21bmc.o obj-$(CONFIG_MFD_HI6421_PMIC) += hi6421-pmic-core.o +obj-$(CONFIG_MFD_HI6421_SPMI) += hi6421-spmi-pmic.o obj-$(CONFIG_MFD_HI655X_PMIC) += hi655x-pmic.o obj-$(CONFIG_MFD_DLN2) += dln2.o obj-$(CONFIG_MFD_RT5033) += rt5033.o
drivers/mfd/hi6421-spmi-pmic.c new file +399 -0
399 lines not on this page · raw message
drivers/regulator/Kconfig +8 -0
@@ -356,6 +356,14 @@ config REGULATOR_HI6421V530 provides 5 general purpose LDOs, and all of them come with support to either ECO (idle) or sleep mode. +config REGULATOR_HI6421V600 + tristate "HiSilicon Hi6421v600 PMIC voltage regulator support" + depends on MFD_HI6421_PMIC && OF + help + This driver provides support for the voltage regulators on + HiSilicon Hi6421v600 PMU / Codec IC. + This is used on Kirin 3670 boards, like HiKey 970. + config REGULATOR_HI655X tristate "Hisilicon HI655X PMIC regulators support" depends on ARCH_HISI || COMPILE_TEST
drivers/regulator/Makefile +1 -0
@@ -44,6 +44,7 @@ obj-$(CONFIG_REGULATOR_FAN53555) += fan53555.o obj-$(CONFIG_REGULATOR_GPIO) += gpio-regulator.o obj-$(CONFIG_REGULATOR_HI6421) += hi6421-regulator.o obj-$(CONFIG_REGULATOR_HI6421V530) += hi6421v530-regulator.o +obj-$(CONFIG_REGULATOR_HI6421V600) += hi6421v600-regulator.o obj-$(CONFIG_REGULATOR_HI655X) += hi655x-regulator.o obj-$(CONFIG_REGULATOR_ISL6271A) += isl6271a-regulator.o obj-$(CONFIG_REGULATOR_ISL9305) += isl9305.o
drivers/regulator/hi6421v600-regulator.c new file +493 -0
493 lines not on this page · raw message
drivers/spmi/Kconfig +9 -0
@@ -25,4 +25,13 @@ config SPMI_MSM_PMIC_ARB This is required for communicating with Qualcomm PMICs and other devices that have the SPMI interface. +config SPMI_HISI3670 + tristate "Hisilicon 3670 SPMI Controller" + select IRQ_DOMAIN_HIERARCHY + depends on HAS_IOMEM + help + If you say yes to this option, support will be included for the + built-in SPMI PMIC Arbiter interface on Hisilicon 3670 + processors. + endif
drivers/spmi/Makefile +2 -0
@@ -5,3 +5,5 @@ obj-$(CONFIG_SPMI) += spmi.o obj-$(CONFIG_SPMI_MSM_PMIC_ARB) += spmi-pmic-arb.o + +obj-$(CONFIG_SPMI_HISI3670) += hisi-spmi-controller.o
drivers/spmi/hisi-spmi-controller.c new file +384 -0
384 lines not on this page · raw message
drivers/spmi/spmi.c +5 -5
@@ -23,6 +23,7 @@ static DEFINE_IDA(ctrl_ida);static void spmi_dev_release (struct device *dev) {struct spmi_device *sdev =to_spmi_device (dev); +kfree (sdev); }
@@ -33,6 +34,7 @@ static const struct device_type spmi_dev_type = {static void spmi_ctrl_release (struct device *dev) {struct spmi_controller *ctrl =to_spmi_controller (dev); +ida_simple_remove (&ctrl_ida, ctrl->nr);kfree (ctrl); }
@@ -487,7 +489,7 @@ static void of_spmi_register_devices(struct spmi_controller *ctrl)continue ; sdev->dev.of_node = node; - sdev->usid = (u8 ) reg[0 ]; + sdev->usid = (u8 )reg[0 ]; err =spmi_device_add (sdev);if (err) {
@@ -531,6 +533,7 @@ EXPORT_SYMBOL_GPL(spmi_controller_add);static int spmi_ctrl_remove_device (struct device *dev,void *data) {struct spmi_device *spmidev =to_spmi_device (dev); +if (dev->type == &spmi_dev_type)spmi_device_remove (spmidev);return 0 ;
@@ -545,13 +548,10 @@ static int spmi_ctrl_remove_device(struct device *dev, void *data)*/ void spmi_controller_remove (struct spmi_controller *ctrl) { -int dummy; -if (!ctrl)return ; - dummy =device_for_each_child (&ctrl->dev,NULL , - spmi_ctrl_remove_device); +device_for_each_child (&ctrl->dev,NULL , spmi_ctrl_remove_device);device_del (&ctrl->dev); }EXPORT_SYMBOL_GPL (spmi_controller_remove);
include/linux/mfd/hi6421-spmi-pmic.h new file +67 -0
67 lines not on this page · raw message
Thanks,
Mauro
Mark Brown
maintainerRe: [PATCH 02/33] spmi, regulator, mfd: add drivers for hikey970 SPMI PMIC
In reply to Mauro Carvalho ChehabQuoted 4 lines · Mauro Carvalho Chehab
drivers/mfd/hisi_pmic_spmi.c | 759 ++++++++++++++++++++++++ drivers/regulator/hisi_regulator_spmi.c | 741 +++++++++++++++++++++++ drivers/spmi/hisi-spmi-controller.c | 390 ++++++++++++ include/linux/mfd/hisi_pmic.h | 165 ++++++
This is a single patch for three subsystems, please split it into per subsystem patches.
Mark Brown
maintainerRe: [PATCH 04/33] mfd, regulator: get rid of unused code at HiSilicon SPMI PMIC
In reply to Mauro Carvalho ChehabQuoted 9 lines · Mauro Carvalho Chehab
There are some checks there which could make sense for downstream builds, but doesn't make much sense for upstream ones. They came from the official Hikey970 tree from Linaro, but even there, the commented-out code is not set via other
Kconfigvars.So, let's just get rid of that. If needed later, this patch can be (partially?) reversed.
Quoted 6 lines
Signed-off-by Mauro Carvalho Chehab <[email protected]>--- drivers/mfd/hisi_pmic_spmi.c | 63 -------- drivers/regulator/hisi_regulator_spmi.c | 196 +----------------------- include/linux/mfd/hisi_pmic.h | 42 ----- 3 files changed, 8 insertions(+), 293 deletions(-)
This is fixing stuff added in the previous patch, please just fold these fixes into the first patch.
Mauro Carvalho Chehab
maintainerRe: [PATCH 02/33] spmi, regulator, mfd: add drivers for hikey970 SPMI PMIC
In reply to Mark BrownEm Tue, 11 Aug 2020 16:58:10 +0100
Mark Brown <[email protected]> escreveu:
Quoted 9 lines · Mauro Carvalho Chehab
Quoted 5 lines
drivers/mfd/hisi_pmic_spmi.c | 759 ++++++++++++++++++++++++ drivers/regulator/hisi_regulator_spmi.c | 741 +++++++++++++++++++++++ drivers/spmi/hisi-spmi-controller.c | 390 ++++++++++++ include/linux/mfd/hisi_pmic.h | 165 ++++++This is a single patch for three subsystems, please split it into per subsystem patches.
Ok, I'll split on a next version.
Yet, it would be good to have all tree drivers applied via the same tree, as those drivers are needed altogether in order for this PMIC to work:
- The SPMI controller driver talks with the hardware and provides support via the SPMI bus calls;
- The MFD PMIC driver binds into the SPMI bus and provide support for interrupts. It also has support for binding the regulator driver;
- The regulator driver needs the PMIC driver (which in turn needs the SPMI bus) in order to be able to talk with the hardware and set the power supplied.
That's basically why I opted to send the entire series altogether.
Thanks,
Mauro
Mark Brown
maintainerQuoted 5 lines · Mauro Carvalho Chehab
This patch series backport the OOT drivers from the Linaro's official tree for this board:
https://github.com/96boards-hikey/linux/tree/hikey970-v4.9
Quoted 7 lines
Porting them to upstream, cleaning up coding style issues, solving driver probing order and adding DT documentation.
I opted to not fold all patches into a single one, in order to:
- Preserve the authorship of the original authors;
- Keep a history of changes.
Please don't do this, please send this as a normal upstream submission like other MFD drivers - split things up per subsystem and fold any fixes into the initial submission of the driver.
Mark Brown
maintainerRe: [PATCH 02/33] spmi, regulator, mfd: add drivers for hikey970 SPMI PMIC
In reply to Mauro Carvalho ChehabQuoted 9 lines · Mauro Carvalho Chehab
Mark Brown <[email protected]> escreveu:
Quoted 2 lines
This is a single patch for three subsystems, please split it into per subsystem patches.
Ok, I'll split on a next version.
Yet, it would be good to have all tree drivers applied via the same tree, as those drivers are needed altogether in order for this PMIC to work:
This is completely normal for MFD drivers, it's still much easier to review things if individual subsystem maintainers can easily get to the code for their subsystem, any Reviewed-bys or whatever can be sensibly applies to relevant code and ideally people can apply patches as they're ready if there's no build time dependencies or Kconfig symbols which prevent build without the dependencies being merged.
Mauro Carvalho Chehab
maintainerRe: [PATCH 02/33] spmi, regulator, mfd: add drivers for hikey970 SPMI PMIC
Em Tue, 11 Aug 2020 17:15:39 +0100
Mark Brown <[email protected]> escreveu:
Quoted 11 lines · Mauro Carvalho Chehab
Quoted 9 lines
Mark Brown <[email protected]> escreveu:
Quoted 2 lines
This is a single patch for three subsystems, please split it into per subsystem patches.
Ok, I'll split on a next version.
Yet, it would be good to have all tree drivers applied via the same tree, as those drivers are needed altogether in order for this PMIC to work:
Quoted 6 lines
This is completely normal for MFD drivers, it's still much easier to review things if individual subsystem maintainers can easily get to the code for their subsystem, any Reviewed-bys or whatever can be sensibly applies to relevant code and ideally people can apply patches as they're ready if there's no build time dependencies or
Kconfigsymbols which prevent build without the dependencies being merged.
Ok. I'll split it into three series.
Before posting the next version, it would be nice to have some feedback specially at the DT documentation patch:
https://lore.kernel.org/lkml/176043f329dfa9889f014feec04e7e1553077873.1597160086.git.mchehab+huawei@kernel.org/T/#u
as any changes there will need to be reflected on the other patches from this series.
Btw, despite being 3 drivers, I added only two DT docs, as the regulator description is done together with the PMIC one.
Thanks,
Mauro
Quoted 20 lines · On Tue, 11 Aug 2020 17:54:29 +0200 Mauro Carvalho Chehab…
Em Tue, 11 Aug 2020 17:41:26 +0200
Mauro Carvalho Chehab <[email protected]> escreveu:Quoted 17 lines
The Hikey 970 board uses a different PMIC than the one found on Hikey 960.
This PMIC uses a SPMI board.
This patch series backport the OOT drivers from the Linaro's official tree for this board:
https://github.com/96boards-hikey/linux/tree/hikey970-v4.9Porting them to upstream, cleaning up coding style issues, solving driver probing order and adding DT documentation.
I opted to not fold all patches into a single one, in order to:
- Preserve the authorship of the original authors;
- Keep a history of changes.
Quoted 9 lines
Quoted 3 lines
As this could be harder for people to review, I'll be replying to patch 00/32 with all patches folded. This should help reviewers to see the current code after the entire series is applied.
As promised, it follows the diff from this entire patch series.
Feel free to review either on the top of this e-mail or on the individual patches.
Whilst I agree entirely with Mark about the need to turn this into a clean series, I was bored at the end of the day so here is a drive by review..
I've not looked at anything that really needed any thought as it is too hot for thinking.
Jonathan
Quoted 104 lines
Thanks!
MauroDocumentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml | 175 ++++++++++++++++++++++++++++++++++++++ Documentation/devicetree/bindings/spmi/hisilicon,hisi-spmi-controller.yaml | 54 ++++++++++++ MAINTAINERS | 8 ++ arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts | 16 +--- arch/arm64/boot/dts/hisilicon/hikey970-pmic.dtsi | 200 ++++++++++++++++++++++++++++++++++++++++++++ drivers/mfd/Kconfig | 17 +++- drivers/mfd/Makefile | 1 + drivers/mfd/hi6421-spmi-pmic.c | 399 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ drivers/regulator/Kconfig | 8 ++ drivers/regulator/Makefile | 1 + drivers/regulator/hi6421v600-regulator.c | 493 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ drivers/spmi/Kconfig | 9 ++ drivers/spmi/Makefile | 2 + drivers/spmi/hisi-spmi-controller.c | 384 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ drivers/spmi/spmi.c | 10 +-- include/linux/mfd/hi6421-spmi-pmic.h | 67 +++++++++++++++ 16 files changed, 1826 insertions(+), 18 deletions(-)Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml new file +76
-0@@ -0,0 +1,175 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/hisilicon,hi6421v600-regulator.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: HiSilicon 6421v600 SPMI PMIC + +maintainers: + - Mauro Carvalho Chehab <[email protected]> + +description: | + HiSilicon 6421v600 uses a MIPI System Power Management (SPMI) bus in order + to provide interrupts and power supply. + + The GPIO and interrupt settings are represented as part of the top-level PMIC + node. + + The SPMI controller part is provided by + Documentation/devicetree/bindings/spmi/hisilicon,hisi-spmi-controller.yaml. + +properties: + $nodename: + pattern: "pmic@[0-9a-f]" + + compatible: + const: hisilicon,hi6421-spmi-pmic + + reg: + maxItems: 1 + + spmi-channel: + description: number of the SPMI channel where the PMIC is connected + + '#interrupt-cells': + const: 2 + + interrupt-controller: + description: + Identify that the PMIC is capable of behaving as an interrupt controller. + + gpios: + maxItems: 1 + + irq-num: + description: Interrupt request number + + 'irq-array': + description: Interrupt request array + + 'irq-mask-addr': + description: Address for the interrupt request mask + + 'irq-addr': + description: Address for the interrupt request + + regulators: + type: object + + properties: + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + patternProperties: + '^ldo@[0-9]+$': + type: object + + $ref: "/schemas/regulator/regulator.yaml#" + + properties: + reg: + description: Enable register. +
Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml line 86
Quoted 10 lines
Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml new file +10
-0+ vsel-reg: + description: Voltage selector register. + + enable-mask: + description: Bitmask used to enable the regulator. + +# voltage-table: +# description: Table with the selector items for the voltage regulator. +# minItems: 2 +# maxItems: 16
Guess this needs fixing up.
Quoted 181 lines
Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml new file +89
-0+ + off-on-delay-us: + description: Time required for changing state to enabled in microseconds. + + startup-delay-us: + description: Startup time in microseconds. + + idle-mode-mask: + description: Bitmask used to put the regulator on idle mode. + + eco-microamp: + description: Maximum current while on idle mode. + + required: + - reg + - vsel-reg + - enable-mask + - voltage-table + - off-on-delay-us + - startup-delay-us + +required: + - compatible + - reg + - spmi-channel + - regulators + +examples: + - | + pmic: pmic@0 { + compatible = "hisilicon,hi6421-spmi-pmic"; + slave_id = <0>; + reg = <0 0>; + + #interrupt-cells = <2>; + interrupt-controller; + gpios = <&gpio28 0 0>; + irq-num = <16>; + irq-array = <2>; + irq-mask-addr = <0x202 2>; + irq-addr = <0x212 2>; + + regulators { + ldo3: ldo3@16 { + reg = <0x16>; + vsel-reg = <0x51>; + + regulator-name = "ldo3"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <2000000>; + regulator-boot-on; + + enable-mask = <0x01>; + + voltage-table = <1500000>, <1550000>, + <1600000>, <1650000>, + <1700000>, <1725000>, + <1750000>, <1775000>, + <1800000>, <1825000>, + <1850000>, <1875000>, + <1900000>, <1925000>, + <1950000>, <2000000>; + off-on-delay-us = <20000>; + startup-delay-us = <120>; + }; + + ldo4: ldo4@17 { /* 40 PIN */ + reg = <0x17>; + vsel-reg = <0x52>; + + regulator-name = "ldo4"; + regulator-min-microvolt = <1725000>; + regulator-max-microvolt = <1900000>; + regulator-boot-on; + + enable-mask = <0x01>; + idle-mode-mask = <0x10>; + eco-microamp = <10000>; + + hi6421-vsel = <0x52 0x07>; + voltage-table = <1725000>, <1750000>, + <1775000>, <1800000>, + <1825000>, <1850000>, + <1875000>, <1900000>; + off-on-delay-us = <20000>; + startup-delay-us = <120>; + }; + }; + };Documentation/devicetree/bindings/spmi/hisilicon,hisi-spmi-controller.yaml new file +54
-0@@ -0,0 +1,54 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spmi/hisilicon,hisi-spmi-controller.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: HiSilicon SPMI controller + +maintainers: + - Mauro Carvalho Chehab <[email protected]> + +description: | + The HiSilicon SPMI controller is found on some Kirin-based designs. + It is a MIPI System Power Management (SPMI) controller. + + The PMIC part is provided by + Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml. + +properties: + $nodename: + pattern: "spmi@[0-9a-f]" + + compatible: + const: hisilicon,spmi-controller + + reg: + maxItems: 1 + + "#address-cells": + const: 2 + + "#size-cells": + const: 0 + + spmi-channel: + const: number of the SPMI channel where the PMIC is connected + +patternProperties: + "^pmic@[0-9a-f]$": + $ref: "/schemas/mfd/hisilicon,hi6421-spmi-pmic.yaml#" + +examples: + - | + spmi: spmi@fff24000 { + compatible = "hisilicon,spmi-controller"; + #address-cells = <2>; + #size-cells = <0>; + status = "ok"; + reg = <0x0 0xfff24000 0x0 0x1000>; + spmi-channel = <2>; + + /* pmic properties */ + + };MAINTAINERS +8
-0@@ -7736,6 +7736,14 @@ F: include/linux/hippidevice.h F: include/uapi/linux/if_hippi.h F: net/802/hippi.c +HISILICON 6421v600 SPMI PMIC DRIVER +M: Mauro Carvalho Chehab <[email protected]> +L: [email protected] +S: Maintained +F: drivers/mfd/hi6421-spmi-pmic.c +F: drivers/regulator/hi6421v600-regulator.c +F: drivers/spmi/spmi.c + HISILICON DMA DRIVER M: Zhou Wang <[email protected]> L: [email protected]arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts +1
-0@@ -12,6 +12,7 @@ #include "hi3670.dtsi" #include "hikey970-pinctrl.dtsi" +#include "hikey970-pmic.dtsi" / { model = "HiKey970";
arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts memory@0 { · line 43
Quoted 5 lines
arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts +1
-1@@ -39,7 +40,7 @@ memory@0 { reg = <0x0 0x0 0x0 0x0>; }; - sd_1v8: regulator-1v8 { + fixed_1v8: regulator-1v8 {
Rename relevant?
Quoted 241 lines
arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts +2
-11compatible = "regulator-fixed"; regulator-name = "fixed-1.8V"; regulator-min-microvolt = <1800000>;@@ -47,15 +48,6 @@ sd_1v8: regulator-1v8 { regulator-always-on; }; - sd_3v3: regulator-3v3 { - compatible = "regulator-fixed"; - regulator-name = "fixed-3.3V"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-boot-on; - regulator-always-on; - }; - wlan_en: wlan-en-1-8v { compatible = "regulator-fixed"; regulator-name = "wlan-en-regulator";@@ -402,8 +394,8 @@ &dwmmc1 { pinctrl-0 = <&sd_pmx_func &sd_clk_cfg_func &sd_cfg_func>; - vmmc-supply = <&sd_3v3>; - vqmmc-supply = <&sd_1v8>; + vmmc-supply = <&ldo16>; + vqmmc-supply = <&ldo9>; status = "okay"; };arch/arm64/boot/dts/hisilicon/hikey970-pmic.dtsi new file +200
-0@@ -0,0 +1,200 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * dts file for Hi6421v600 SPMI PMIC used at the HiKey970 Development Board + * + * Copyright (C) 2020, Huawei Tech. Co., Ltd. + */ + +/ { + spmi: spmi@fff24000 { + compatible = "hisilicon,spmi-controller"; + #address-cells = <2>; + #size-cells = <0>; + status = "ok"; + reg = <0x0 0xfff24000 0x0 0x1000>; + spmi-channel = <2>; + + pmic: pmic@0 { + compatible = "hisilicon,hi6421-spmi-pmic"; + slave_id = <0>; + reg = <0 0>; + + #interrupt-cells = <2>; + interrupt-controller; + gpios = <&gpio28 0 0>; + irq-num = <16>; + irq-array = <2>; + irq-mask-addr = <0x202 2>; + irq-addr = <0x212 2>; + + regulators { + #address-cells = <1>; + #size-cells = <0>; + + ldo3: ldo3@16 { + reg = <0x16>; + vsel-reg = <0x51>; + + regulator-name = "ldo3"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <2000000>; + regulator-boot-on; + + enable-mask = <0x01>; + + voltage-table = <1500000>, <1550000>, + <1600000>, <1650000>, + <1700000>, <1725000>, + <1750000>, <1775000>, + <1800000>, <1825000>, + <1850000>, <1875000>, + <1900000>, <1925000>, + <1950000>, <2000000>; + off-on-delay-us = <20000>; + startup-delay-us = <120>; + }; + + ldo4: ldo4@17 { /* 40 PIN */ + reg = <0x17>; + vsel-reg = <0x52>; + + regulator-name = "ldo4"; + regulator-min-microvolt = <1725000>; + regulator-max-microvolt = <1900000>; + regulator-boot-on; + + enable-mask = <0x01>; + idle-mode-mask = <0x10>; + eco-microamp = <10000>; + + hi6421-vsel = <0x52 0x07>; + voltage-table = <1725000>, <1750000>, + <1775000>, <1800000>, + <1825000>, <1850000>, + <1875000>, <1900000>; + off-on-delay-us = <20000>; + startup-delay-us = <120>; + }; + + ldo9: ldo9@1C { /* SDCARD I/O */ + reg = <0x1C>; + vsel-reg = <0x57>; + + regulator-name = "ldo9"; + regulator-min-microvolt = <1750000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + + enable-mask = <0x01>; + idle-mode-mask = <0x10>; + eco-microamp = <10000>; + + voltage-table = <1750000>, <1800000>, + <1825000>, <2800000>, + <2850000>, <2950000>, + <3000000>, <3300000>; + off-on-delay-us = <20000>; + startup-delay-us = <360>; + }; + + ldo15: ldo15@21 { /* UFS */ + reg = <0x21>; + vsel-reg = <0x5c>; + + regulator-name = "ldo15"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + + enable-mask = <0x01>; + idle-mode-mask = <0x10>; + eco-microamp = <10000>; + + voltage-table = <1800000>, <1850000>, + <2400000>, <2600000>, + <2700000>, <2850000>, + <2950000>, <3000000>; + off-on-delay-us = <20000>; + startup-delay-us = <120>; + }; + + ldo16: ldo16@22 { /* SD */ + reg = <0x22>; + vsel-reg = <0x5d>; + + regulator-name = "ldo16"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + + enable-mask = <0x01>; + idle-mode-mask = <0x10>; + eco-microamp = <10000>; + + voltage-table = <1800000>, <1850000>, + <2400000>, <2600000>, + <2700000>, <2850000>, + <2950000>, <3000000>; + off-on-delay-us = <20000>; + startup-delay-us = <360>; + }; + + ldo17: ldo17@23 { + reg = <0x23>; + vsel-reg = <0x5e>; + + regulator-name = "ldo17"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <3300000>; + + enable-mask = <0x01>; + idle-mode-mask = <0x10>; + eco-microamp = <10000>; + + voltage-table = <2500000>, <2600000>, + <2700000>, <2800000>, + <3000000>, <3100000>, + <3200000>, <3300000>; + off-on-delay-us = <20000>; + startup-delay-us = <120>; + }; + + ldo33: ldo33@32 { /* PEX8606 */ + reg = <0x32>; + vsel-reg = <0x6d>; + regulator-name = "ldo33"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + + enable-mask = <0x01>; + + voltage-table = <2500000>, <2600000>, + <2700000>, <2800000>, + <3000000>, <3100000>, + <3200000>, <3300000>; + off-on-delay-us = <20000>; + startup-delay-us = <120>; + }; + + ldo34: ldo34@33 { /* GPS AUX IN VDD */ + reg = <0x33>; + vsel-reg = <0x6e>; + + regulator-name = "ldo34"; + regulator-min-microvolt = <2600000>; + regulator-max-microvolt = <3300000>; + + enable-mask = <0x01>; + + voltage-table = <2600000>, <2700000>, + <2800000>, <2900000>, + <3000000>, <3100000>, + <3200000>, <3300000>; + off-on-delay-us = <20000>; + startup-delay-us = <120>; + }; + }; + }; + }; +};drivers/mfd/Kconfig +0
-0
drivers/mfd/Kconfig config MFD_HI6421_PMIC · line 496
Quoted 5 lines
drivers/mfd/Kconfig +1
-1@@ -493,10 +493,25 @@ config MFD_HI6421_PMIC Add support for HiSilicon Hi6421 PMIC. Hi6421 includes multi- functions, such as regulators, RTC, codec, Coulomb counter, etc. This driver includes core APIs _only_. You have to select - individul components like voltage regulators under corresponding + individual components like voltage regulators under corresponding
Don't fix other drivers.
drivers/mfd/Kconfig config MFD_HI6421_PMIC · line 504
Quoted 8 lines
drivers/mfd/Kconfig +5
-0menus in order to enable them. We communicate with the Hi6421 via memory-mapped I/O. +config MFD_HI6421_SPMI + tristate "HiSilicon Hi6421v600 SPMI PMU/Codec IC" + depends on OF + select MFD_CORE + select REGMAP_MMIO
Nice thought, but it doesn't use it yet!
Quoted 37 lines
drivers/mfd/Kconfig +10
-0+ help + Add support for HiSilicon Hi6421v600 SPMI PMIC. Hi6421 includes + multi-functions, such as regulators, RTC, codec, Coulomb counter, + etc. + + This driver includes core APIs _only_. You have to select + individual components like voltage regulators under corresponding + menus in order to enable them. + We communicate with the Hi6421v600 via a SPMI bus. + config MFD_HI655X_PMIC tristate "HiSilicon Hi655X series PMU/Codec IC" depends on ARCH_HISI || COMPILE_TESTdrivers/mfd/Makefile +1
-0@@ -233,6 +233,7 @@ obj-$(CONFIG_MFD_IPAQ_MICRO) += ipaq-micro.o obj-$(CONFIG_MFD_IQS62X) += iqs62x.o obj-$(CONFIG_MFD_MENF21BMC) += menf21bmc.o obj-$(CONFIG_MFD_HI6421_PMIC) += hi6421-pmic-core.o +obj-$(CONFIG_MFD_HI6421_SPMI) += hi6421-spmi-pmic.o obj-$(CONFIG_MFD_HI655X_PMIC) += hi655x-pmic.o obj-$(CONFIG_MFD_DLN2) += dln2.o obj-$(CONFIG_MFD_RT5033) += rt5033.odrivers/mfd/hi6421-spmi-pmic.c new file +6
-0@@ -0,0 +1,399 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* Device driver for regulators in HISI PMIC IC +* +* Copyright (c) 2013 Linaro Ltd. +* Copyright (c) 2011 Hisilicon.
drivers/mfd/hi6421-spmi-pmic.c line 16
Quoted 10 lines
drivers/mfd/hi6421-spmi-pmic.c new file +10
-0+* +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details.
Drop license text.
Quoted 12 lines
drivers/mfd/hi6421-spmi-pmic.c new file +12
-0+* +*/ + +#include <linux/slab.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <linux/module.h> +#include <linux/err.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/mfd/core.h> +#include <linux/platform_device.h>
drivers/mfd/hi6421-spmi-pmic.c line 38
Quoted 10 lines
drivers/mfd/hi6421-spmi-pmic.c new file +10
-0+#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/of_device.h> +#include <linux/of_gpio.h> +#include <linux/of_irq.h> +#include <linux/mfd/hi6421-spmi-pmic.h> +#include <linux/irq.h> +#include <linux/spmi.h> +#ifndef NO_IRQ +#define NO_IRQ 0
Drop
drivers/mfd/hi6421-spmi-pmic.c line 49
Quoted 11 lines
drivers/mfd/hi6421-spmi-pmic.c new file +11
-0+#endif + +/* 8-bit register offset in PMIC */ +#define HISI_MASK_STATE 0xff + +#define HISI_IRQ_KEY_NUM 0 +#define HISI_IRQ_KEY_VALUE 0xc0 +#define HISI_IRQ_KEY_DOWN 7 +#define HISI_IRQ_KEY_UP 6 + +/*#define HISI_NR_IRQ 25*/
Drop
Quoted 4 lines
drivers/mfd/hi6421-spmi-pmic.c new file +4
-0+#define HISI_MASK_FIELD 0xFF +#define HISI_BITS 8 + +/*define the first group interrupt register number*/
drivers/mfd/hi6421-spmi-pmic.c line 63
Quoted 10 lines
drivers/mfd/hi6421-spmi-pmic.c new file +10
-0+#define HISI_PMIC_FIRST_GROUP_INT_NUM 2 + +static const struct mfd_cell hi6421v600_devs[] = { + { .name ="hi6421v600-regulator" , }, +}; + +/* +* The PMIC register is only 8-bit. +* Hisilicon SoC use hardware to map PMIC register into SoC mapping. +* At here, we are accessing SoC register with 32-bit.
Can we return the 8 bits in an int and hence also return error codes?
Quoted 139 lines
drivers/mfd/hi6421-spmi-pmic.c new file +139
-0+*/ +u32 hi6421_spmi_pmic_read (struct hi6421_spmi_pmic *pmic,int reg) +{ +u32 ret; +u8 read_value =0 ; +struct spmi_device *pdev; + + pdev =to_spmi_device (pmic->dev); +if (!pdev) { +pr_err ("%s: pdev get failed!\n" , __func__); +return 0 ; + } + + ret =spmi_ext_register_readl (pdev, reg, + (unsigned char *)&read_value,1 ); +if (ret) { +pr_err ("%s: spmi_ext_register_readl failed!\n" , __func__); +return 0 ; + } +return (u32 )read_value; +} +EXPORT_SYMBOL (hi6421_spmi_pmic_read); + +void hi6421_spmi_pmic_write (struct hi6421_spmi_pmic *pmic,int reg,u32 val) +{ +u32 ret; +struct spmi_device *pdev; + + pdev =to_spmi_device (pmic->dev); +if (!pdev) { +pr_err ("%s: pdev get failed!\n" , __func__); +return ; + } + + ret =spmi_ext_register_writel (pdev, reg, (unsigned char *)&val,1 ); +if (ret) { +pr_err ("%s: spmi_ext_register_writel failed!\n" , __func__); +return ; + } +} +EXPORT_SYMBOL (hi6421_spmi_pmic_write); + +void hi6421_spmi_pmic_rmw (struct hi6421_spmi_pmic *pmic,int reg, +u32 mask,u32 bits) +{ +u32 data; +unsigned long flags; + +spin_lock_irqsave (&pmic->lock, flags); + data =hi6421_spmi_pmic_read (pmic, reg) & ~mask; + data |= mask & bits; +hi6421_spmi_pmic_write (pmic, reg, data); +spin_unlock_irqrestore (&pmic->lock, flags); +} +EXPORT_SYMBOL (hi6421_spmi_pmic_rmw); + +static irqreturn_t hi6421_spmi_irq_handler (int irq,void *data) +{ +struct hi6421_spmi_pmic *pmic = (struct hi6421_spmi_pmic *)data; +unsigned long pending; +int i, offset; + +for (i =0 ; i < pmic->irqarray; i++) { + pending =hi6421_spmi_pmic_read (pmic, (i + pmic->irq_addr.start_addr)); + pending &=HISI_MASK_FIELD ; +if (pending !=0 ) +pr_debug ("pending[%d]=0x%lx\n\r" , i, pending); + +hi6421_spmi_pmic_write (pmic, (i + pmic->irq_addr.start_addr), + pending); + +/* solve powerkey order */ +if ((i ==HISI_IRQ_KEY_NUM ) && ((pending &HISI_IRQ_KEY_VALUE ) ==HISI_IRQ_KEY_VALUE )) { +generic_handle_irq (pmic->irqs[HISI_IRQ_KEY_DOWN ]); +generic_handle_irq (pmic->irqs[HISI_IRQ_KEY_UP ]); + pending &= (~HISI_IRQ_KEY_VALUE ); + } + +if (pending) { +for_each_set_bit (offset, &pending,HISI_BITS ) +generic_handle_irq (pmic->irqs[offset + i *HISI_BITS ]); + } + } + +return IRQ_HANDLED ; +} + +static void hi6421_spmi_irq_mask (struct irq_data *d) +{ +struct hi6421_spmi_pmic *pmic =irq_data_get_irq_chip_data (d); +u32 data, offset; +unsigned long flags; + + offset = (irqd_to_hwirq (d) >>3 ); + offset += pmic->irq_mask_addr.start_addr; + +spin_lock_irqsave (&pmic->lock, flags); + data =hi6421_spmi_pmic_read (pmic, offset); + data |= (1 << (irqd_to_hwirq (d) &0x07 )); +hi6421_spmi_pmic_write (pmic, offset, data); +spin_unlock_irqrestore (&pmic->lock, flags); +} + +static void hi6421_spmi_irq_unmask (struct irq_data *d) +{ +struct hi6421_spmi_pmic *pmic =irq_data_get_irq_chip_data (d); +u32 data, offset; +unsigned long flags; + + offset = (irqd_to_hwirq (d) >>3 ); + offset += pmic->irq_mask_addr.start_addr; + +spin_lock_irqsave (&pmic->lock, flags); + data =hi6421_spmi_pmic_read (pmic, offset); + data &= ~(1 << (irqd_to_hwirq (d) &0x07 )); +hi6421_spmi_pmic_write (pmic, offset, data); +spin_unlock_irqrestore (&pmic->lock, flags); +} + +static struct irq_chip hi6421_spmi_pmu_irqchip = { + .name ="hisi-irq" , + .irq_mask = hi6421_spmi_irq_mask, + .irq_unmask = hi6421_spmi_irq_unmask, + .irq_disable = hi6421_spmi_irq_mask, + .irq_enable = hi6421_spmi_irq_unmask, +}; + +static int hi6421_spmi_irq_map (struct irq_domain *d,unsigned int virq, +irq_hw_number_t hw) +{ +struct hi6421_spmi_pmic *pmic = d->host_data; + +irq_set_chip_and_handler_name (virq, &hi6421_spmi_pmu_irqchip, + handle_simple_irq,"hisi" ); +irq_set_chip_data (virq, pmic); +irq_set_irq_type (virq,IRQ_TYPE_NONE ); + +return 0 ; +}
drivers/mfd/hi6421-spmi-pmic.c line 212
Quoted 10 lines
drivers/mfd/hi6421-spmi-pmic.c new file +10
-0+ +static const struct irq_domain_ops hi6421_spmi_domain_ops = { + .map = hi6421_spmi_irq_map, + .xlate = irq_domain_xlate_twocell, +}; + +static int get_pmic_device_tree_data (struct device_node *np, +struct hi6421_spmi_pmic *pmic) +{ +int ret =0 ;
always set.
drivers/mfd/hi6421-spmi-pmic.c line 214
Quoted 2 lines
drivers/mfd/hi6421-spmi-pmic.c new file +2
-0+ +/*get pmic irq num*/
Comments are mostly fiarly obvious.
Also if there is one, why use an array read?
Quoted 8 lines
drivers/mfd/hi6421-spmi-pmic.c new file +8
-0+ ret =of_property_read_u32_array (np,"irq-num" , + &pmic->irqnum,1 ); +if (ret) { +pr_err ("no irq-num property set\n" ); + ret = -ENODEV ; +return ret; + } +
drivers/mfd/hi6421-spmi-pmic.c line 232
Quoted 10 lines
drivers/mfd/hi6421-spmi-pmic.c new file +10
-0+/*get pmic irq array number*/ + ret =of_property_read_u32_array (np,"irq-array" , + &pmic->irqarray,1 ); +if (ret) { +pr_err ("no irq-array property set\n" ); + ret = -ENODEV ; +return ret; + } + +/*SOC_PMIC_IRQ_MASK_0_ADDR*/
spacing in comments.
drivers/mfd/hi6421-spmi-pmic.c line 241
Quoted 9 lines
drivers/mfd/hi6421-spmi-pmic.c new file +9
-0+ ret =of_property_read_u32_array (np,"irq-mask-addr" , + (int *)&pmic->irq_mask_addr,2 ); +if (ret) { +pr_err ("no irq-mask-addr property set\n" ); + ret = -ENODEV ; +return ret; + } + +/*SOC_PMIC_IRQ0_ADDR*/
These superficially feel like things that would come from the compatible, but maybe I'm missing something.
drivers/mfd/hi6421-spmi-pmic.c line 243
Quoted 2 lines
drivers/mfd/hi6421-spmi-pmic.c new file +2
-0+ ret =of_property_read_u32_array (np,"irq-addr" , + (int *)&pmic->irq_addr,2 );
Unsurprisingly this takes a u32 * not a int *
Quoted 32 lines
drivers/mfd/hi6421-spmi-pmic.c new file +32
-0+ if (ret) {f_prop + pr_err("no irq-addr property set\n"); + ret = -ENODEV ; +return ret; + } + +return ret; +} + +static void hi6421_spmi_pmic_irq_prc (struct hi6421_spmi_pmic *pmic) +{ +int i; + +for (i =0 ; i < pmic->irq_mask_addr.array; i++) +hi6421_spmi_pmic_write (pmic, pmic->irq_mask_addr.start_addr + i, +HISI_MASK_STATE ); + +for (i =0 ; i < pmic->irq_addr.array; i++) { +unsigned int pending =hi6421_spmi_pmic_read (pmic, pmic->irq_addr.start_addr + i); + +pr_debug ("PMU IRQ address value:irq[0x%x] = 0x%x\n" , + pmic->irq_addr.start_addr + i, pending); +hi6421_spmi_pmic_write (pmic, pmic->irq_addr.start_addr + i, +HISI_MASK_STATE ); + } +} + +static int hi6421_spmi_pmic_probe (struct spmi_device *pdev) +{ +struct device *dev = &pdev->dev; +struct device_node *np = dev->of_node; +struct hi6421_spmi_pmic *pmic =NULL ;
drivers/mfd/hi6421-spmi-pmic.c line 285
Quoted 10 lines
drivers/mfd/hi6421-spmi-pmic.c new file +10
-0+enum of_gpio_flags flags; +int ret =0 ; +int i; +unsigned int virq; + + pmic =devm_kzalloc (dev,sizeof (*pmic),GFP_KERNEL ); +if (!pmic) +return -ENOMEM ; + +/*TODO: get pmic dts info*/
Seems to be done?
drivers/mfd/hi6421-spmi-pmic.c line 297
Quoted 12 lines
drivers/mfd/hi6421-spmi-pmic.c new file +12
-0+ ret =get_pmic_device_tree_data (np, pmic); +if (ret) { +dev_err (&pdev->dev,"Error reading hisi pmic dts\n" ); +return ret; + } + +/* TODO: get and enable clk request */ +spin_lock_init (&pmic->lock); + + pmic->dev = dev; + + pmic->gpio =of_get_gpio_flags (np,0 , &flags);
Do we need flags for something?
Can we use the gpio/consumer.h interfaces for all this?
Though I'm not sure we need a gpio at all. Looks like we just use it as an interrupt. Get an interrupt directly instead.
Quoted 28 lines
drivers/mfd/hi6421-spmi-pmic.c new file +28
-0+if (pmic->gpio <0 ) +return pmic->gpio; + +if (!gpio_is_valid (pmic->gpio)) +return -EINVAL ; + + ret =gpio_request_one (pmic->gpio,GPIOF_IN ,"pmic" ); +if (ret <0 ) { +dev_err (dev,"failed to request gpio%d\n" , pmic->gpio); +return ret; + } + + pmic->irq =gpio_to_irq (pmic->gpio); + +/* mask && clear IRQ status */ +hi6421_spmi_pmic_irq_prc (pmic); + + pmic->irqs =devm_kzalloc (dev, pmic->irqnum *sizeof (int ),GFP_KERNEL ); +if (!pmic->irqs) + goto irq_malloc; + + pmic->domain =irq_domain_add_simple (np, pmic->irqnum,0 , + &hi6421_spmi_domain_ops, pmic); +if (!pmic->domain) { +dev_err (dev,"failed irq domain add simple!\n" ); + ret = -ENODEV ; + goto irq_domain; + }
drivers/mfd/hi6421-spmi-pmic.c line 335
Quoted 10 lines
drivers/mfd/hi6421-spmi-pmic.c new file +10
-0+ +for (i =0 ; i < pmic->irqnum; i++) { + virq =irq_create_mapping (pmic->domain, i); +if (virq ==NO_IRQ ) { +pr_debug ("Failed mapping hwirq\n" ); + ret = -ENOSPC ; + goto irq_create_mapping; + } + pmic->irqs[i] = virq; +pr_info ("[%s]. pmic->irqs[%d] = %d\n" , __func__, i, pmic->irqs[i]);
Noise
Quoted 12 lines
drivers/mfd/hi6421-spmi-pmic.c new file +12
-0+ } + + ret =request_threaded_irq (pmic->irq, hi6421_spmi_irq_handler,NULL , +IRQF_TRIGGER_LOW |IRQF_SHARED |IRQF_NO_SUSPEND , +"pmic" , pmic); +if (ret <0 ) { +dev_err (dev,"could not claim pmic %d\n" , ret); + ret = -ENODEV ; + goto request_theaded_irq; + } + +dev_set_drvdata (&pdev->dev, pmic);
drivers/mfd/hi6421-spmi-pmic.c line 357
Quoted 10 lines
drivers/mfd/hi6421-spmi-pmic.c new file +10
-0+ +/* +* The logic below will rely that the pmic is already stored at +* drvdata. +*/ +dev_dbg (&pdev->dev,"SPMI-PMIC: adding children for %pOF\n" , + pdev->dev.of_node); + ret =devm_mfd_add_devices (&pdev->dev,PLATFORM_DEVID_NONE , + hi6421v600_devs,ARRAY_SIZE (hi6421v600_devs), +NULL ,0 ,NULL );
This is mixing and matching managed an unmanaged. Should be one or the other or we might be hiding some race conditions.
Quoted 12 lines
drivers/mfd/hi6421-spmi-pmic.c new file +12
-0+if (ret) { +dev_err (&pdev->dev,"Failed to add child devices: %d\n" , ret); +return ret; + } + +return 0 ; + +request_theaded_irq: +irq_create_mapping: +irq_domain: +irq_malloc: +gpio_free (pmic->gpio);
drivers/mfd/hi6421-spmi-pmic.c line 379
Quoted 10 lines
drivers/mfd/hi6421-spmi-pmic.c new file +10
-0+return ret; +} + +static void hi6421_spmi_pmic_remove (struct spmi_device *pdev) +{ +struct hi6421_spmi_pmic *pmic =dev_get_drvdata (&pdev->dev); + +free_irq (pmic->irq, pmic); +gpio_free (pmic->gpio); +devm_kfree (&pdev->dev, pmic);
I hope that isn't needed!
Quoted 25 lines
drivers/mfd/hi6421-spmi-pmic.c new file +20
-0+} + +static const struct of_device_id pmic_spmi_id_table[] = { + { .compatible ="hisilicon,hi6421-spmi-pmic" }, + { } +}; +MODULE_DEVICE_TABLE (of, pmic_spmi_id_table); + +static struct spmi_driver hi6421_spmi_pmic_driver = { + .driver = { + .name ="hi6421-spmi-pmic" , + .of_match_table = pmic_spmi_id_table, + }, + .probe = hi6421_spmi_pmic_probe, + .remove = hi6421_spmi_pmic_remove, +}; +module_spmi_driver (hi6421_spmi_pmic_driver); + +MODULE_DESCRIPTION ("HiSilicon Hi6421v600 SPMI PMIC driver" ); +MODULE_LICENSE ("GPL v2" );drivers/regulator/Kconfig +0
-0
drivers/regulator/Kconfig config REGULATOR_HI6421V530 · line 361
Quoted 6 lines
drivers/regulator/Kconfig +3
-0@@ -356,6 +356,14 @@ config REGULATOR_HI6421V530 provides 5 general purpose LDOs, and all of them come with support to either ECO (idle) or sleep mode. +config REGULATOR_HI6421V600 + tristate "HiSilicon Hi6421v600 PMIC voltage regulator support" + depends on MFD_HI6421_PMIC && OF
Can we do a COMPILE_TEST here?
Quoted 33 lines
drivers/regulator/Kconfig +5
-0+ help + This driver provides support for the voltage regulators on + HiSilicon Hi6421v600 PMU / Codec IC. + This is used on Kirin 3670 boards, like HiKey 970. + config REGULATOR_HI655X tristate "Hisilicon HI655X PMIC regulators support" depends on ARCH_HISI || COMPILE_TESTdrivers/regulator/Makefile +1
-0@@ -44,6 +44,7 @@ obj-$(CONFIG_REGULATOR_FAN53555) += fan53555.o obj-$(CONFIG_REGULATOR_GPIO) += gpio-regulator.o obj-$(CONFIG_REGULATOR_HI6421) += hi6421-regulator.o obj-$(CONFIG_REGULATOR_HI6421V530) += hi6421v530-regulator.o +obj-$(CONFIG_REGULATOR_HI6421V600) += hi6421v600-regulator.o obj-$(CONFIG_REGULATOR_HI655X) += hi655x-regulator.o obj-$(CONFIG_REGULATOR_ISL6271A) += isl6271a-regulator.o obj-$(CONFIG_REGULATOR_ISL9305) += isl9305.odrivers/regulator/hi6421v600-regulator.c new file +7
-0@@ -0,0 +1,493 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* Device driver for regulators in Hisi IC +* +* Copyright (c) 2013 Linaro Ltd. +* Copyright (c) 2011 Hisilicon. +*
drivers/regulator/hi6421v600-regulator.c line 17
Quoted 10 lines
drivers/regulator/hi6421v600-regulator.c new file +10
-0+* Guodong Xu <[email protected]> +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details.
Need to remove license text as have SPDX.
Blank line doesn't add anything here.
Quoted 16 lines
drivers/regulator/hi6421v600-regulator.c new file +16
-0+* +*/ + +#include <linux/slab.h> +#include <linux/device.h> +#include <linux/module.h> +#include <linux/err.h> +#include <linux/io.h> +#include <linux/platform_device.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/of_address.h> +#include <linux/regmap.h> +#include <linux/regulator/driver.h> +#include <linux/regulator/machine.h> +#include <linux/regulator/of_regulator.h>
drivers/regulator/hi6421v600-regulator.c line 43
Quoted 10 lines
drivers/regulator/hi6421v600-regulator.c new file +10
-0+#include <linux/mfd/hi6421-spmi-pmic.h> +#include <linux/delay.h> +#include <linux/time.h> +#include <linux/version.h> +#include <linux/seq_file.h> +#include <linux/uaccess.h> +#include <linux/spmi.h> + +#define rdev_dbg(rdev, fmt, arg...) \ + pr_debug("%s: %s: " fmt, (rdev)->desc->name, __func__, ##arg)
Not worth defining in my view.
Quoted 86 lines
drivers/regulator/hi6421v600-regulator.c new file +86
-0+ +struct hi6421v600_regulator { +struct regulator_desc rdesc; +struct hi6421_spmi_pmic *pmic; +u32 eco_mode_mask, eco_uA; +}; + +static DEFINE_MUTEX (enable_mutex); + +/* helper function to ensure when it returns it is at least 'delay_us' +* microseconds after 'since'. +*/ + +static int hi6421_spmi_regulator_is_enabled (struct regulator_dev *rdev) +{ +u32 reg_val; +struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev); +struct hi6421_spmi_pmic *pmic = sreg->pmic; + + reg_val =hi6421_spmi_pmic_read (pmic, rdev->desc->enable_reg); + +rdev_dbg (rdev, +"enable_reg=0x%x, val= 0x%x, enable_state=%d\n" , + rdev->desc->enable_reg, + reg_val, (reg_val & rdev->desc->enable_mask)); + +return ((reg_val & rdev->desc->enable_mask) !=0 ); +} + +static int hi6421_spmi_regulator_enable (struct regulator_dev *rdev) +{ +struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev); +struct hi6421_spmi_pmic *pmic = sreg->pmic; + +/* cannot enable more than one regulator at one time */ +mutex_lock (&enable_mutex); +usleep_range (HISI_REGS_ENA_PROTECT_TIME , +HISI_REGS_ENA_PROTECT_TIME +1000 ); + +/* set enable register */ +rdev_dbg (rdev, +"off_on_delay=%d us, enable_reg=0x%x, enable_mask=0x%x\n" , + rdev->desc->off_on_delay, rdev->desc->enable_reg, + rdev->desc->enable_mask); + +hi6421_spmi_pmic_rmw (pmic, rdev->desc->enable_reg, + rdev->desc->enable_mask, + rdev->desc->enable_mask); + +mutex_unlock (&enable_mutex); + +return 0 ; +} + +static int hi6421_spmi_regulator_disable (struct regulator_dev *rdev) +{ +struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev); +struct hi6421_spmi_pmic *pmic = sreg->pmic; + +/* set enable register to 0 */ +rdev_dbg (rdev,"enable_reg=0x%x, enable_mask=0x%x\n" , + rdev->desc->enable_reg, rdev->desc->enable_mask); + +hi6421_spmi_pmic_rmw (pmic, rdev->desc->enable_reg, + rdev->desc->enable_mask,0 ); + +return 0 ; +} + +static int hi6421_spmi_regulator_get_voltage_sel (struct regulator_dev *rdev) +{ +struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev); +struct hi6421_spmi_pmic *pmic = sreg->pmic; +u32 reg_val, selector; + +/* get voltage selector */ + reg_val =hi6421_spmi_pmic_read (pmic, rdev->desc->vsel_reg); + + selector = (reg_val & rdev->desc->vsel_mask) >> (ffs (rdev->desc->vsel_mask) -1 ); + +rdev_dbg (rdev, +"vsel_reg=0x%x, value=0x%x, entry=0x%x, voltage=%d mV\n" , + rdev->desc->vsel_reg, reg_val, selector, + rdev->desc->ops->list_voltage (rdev, selector) /1000 ); + +return selector;
drivers/regulator/hi6421v600-regulator.c line 139
Quoted 10 lines
drivers/regulator/hi6421v600-regulator.c new file +10
-0+} + +static int hi6421_spmi_regulator_set_voltage_sel (struct regulator_dev *rdev, +unsigned int selector) +{ +struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev); +struct hi6421_spmi_pmic *pmic = sreg->pmic; +u32 reg_val; + +/* unlikely to happen. sanity test done by regulator core */
Unlikely or can't?
Quoted 66 lines
drivers/regulator/hi6421v600-regulator.c new file +66
-0+if (unlikely (selector >= rdev->desc->n_voltages)) +return -EINVAL ; + + reg_val = selector << (ffs (rdev->desc->vsel_mask) -1 ); + +/* set voltage selector */ +rdev_dbg (rdev, +"vsel_reg=0x%x, mask=0x%x, value=0x%x, voltage=%d mV\n" , + rdev->desc->vsel_reg, rdev->desc->vsel_mask, reg_val, + rdev->desc->ops->list_voltage (rdev, selector) /1000 ); + +hi6421_spmi_pmic_rmw (pmic, rdev->desc->vsel_reg, + rdev->desc->vsel_mask, reg_val); + +return 0 ; +} + +static unsigned int hi6421_spmi_regulator_get_mode (struct regulator_dev *rdev) +{ +struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev); +struct hi6421_spmi_pmic *pmic = sreg->pmic; +u32 reg_val; +unsigned int mode; + + reg_val =hi6421_spmi_pmic_read (pmic, rdev->desc->enable_reg); + +if (reg_val & sreg->eco_mode_mask) + mode =REGULATOR_MODE_IDLE ; +else + mode =REGULATOR_MODE_NORMAL ; + +rdev_dbg (rdev, +"enable_reg=0x%x, eco_mode_mask=0x%x, reg_val=0x%x, %s mode\n" , + rdev->desc->enable_reg, sreg->eco_mode_mask, reg_val, + mode ==REGULATOR_MODE_IDLE ?"idle" :"normal" ); + +return mode; +} + +static int hi6421_spmi_regulator_set_mode (struct regulator_dev *rdev, +unsigned int mode) +{ +struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev); +struct hi6421_spmi_pmic *pmic = sreg->pmic; +u32 val; + +switch (mode) { +case REGULATOR_MODE_NORMAL : + val =0 ; +break ; +case REGULATOR_MODE_IDLE : + val = sreg->eco_mode_mask << (ffs (sreg->eco_mode_mask) -1 ); +break ; +default : +return -EINVAL ; + } + +/* set mode */ +rdev_dbg (rdev,"enable_reg=0x%x, eco_mode_mask=0x%x, value=0x%x\n" , + rdev->desc->enable_reg, sreg->eco_mode_mask, val); + +hi6421_spmi_pmic_rmw (pmic, rdev->desc->enable_reg, + sreg->eco_mode_mask, val); + +return 0 ; +}
drivers/regulator/hi6421v600-regulator.c line 215
Quoted 10 lines
drivers/regulator/hi6421v600-regulator.c new file +10
-0+ +static unsigned int +hi6421_spmi_regulator_get_optimum_mode (struct regulator_dev *rdev, +int input_uV,int output_uV, +int load_uA) +{ +struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev); + +if (load_uA || ((unsigned int )load_uA > sreg->eco_uA)) { +rdev_dbg (rdev,"normal mode" );
Debug seems unnecessary to me, but maybe keep it if you want.
Quoted 35 lines
drivers/regulator/hi6421v600-regulator.c new file +35
-0+return REGULATOR_MODE_NORMAL ; + }else { +rdev_dbg (rdev,"idle mode" ); +return REGULATOR_MODE_IDLE ; + } +} + +static int hi6421_spmi_dt_parse (struct platform_device *pdev, +struct hi6421v600_regulator *sreg, +struct regulator_desc *rdesc) +{ +struct device *dev = &pdev->dev; +struct device_node *np = dev->of_node; +unsigned int *v_table; +int ret; + + ret =of_property_read_u32 (np,"reg" , &rdesc->enable_reg); +if (ret) { +dev_err (dev,"missing reg property\nn" ); +return ret; + } + + ret =of_property_read_u32 (np,"vsel-reg" , &rdesc->vsel_reg); +if (ret) { +dev_err (dev,"missing vsel-reg property\n" ); +return ret; + } + + ret =of_property_read_u32 (np,"enable-mask" , &rdesc->enable_mask); +if (ret) { +dev_err (dev,"missing enable-mask property\n" ); +return ret; + } + +/*
drivers/regulator/hi6421v600-regulator.c line 260
Quoted 10 lines
drivers/regulator/hi6421v600-regulator.c new file +10
-0+* Not all regulators work on idle mode +*/ + ret =of_property_read_u32 (np,"idle-mode-mask" , &sreg->eco_mode_mask); +if (ret) { +dev_dbg (dev,"LDO doesn't support economy mode.\n" ); + sreg->eco_mode_mask =0 ; + sreg->eco_uA =0 ; + }else { + ret =of_property_read_u32 (np,"eco-microamp" , + &sreg->eco_uA);
one line.
Quoted 61 lines
drivers/regulator/hi6421v600-regulator.c new file +61
-0+if (ret) { +dev_err (dev,"missing eco-microamp property\n" ); +return ret; + } + } + +/* parse .off-on-delay */ + ret =of_property_read_u32 (np,"off-on-delay-us" , + &rdesc->off_on_delay); +if (ret) { +dev_err (dev,"missing off-on-delay-us property\n" ); +return ret; + } + +/* parse .enable_time */ + ret =of_property_read_u32 (np,"startup-delay-us" , + &rdesc->enable_time); +if (ret) { +dev_err (dev,"missing startup-delay-us property\n" ); +return ret; + } + +/* FIXME: are there a better value for this? */ + rdesc->ramp_delay = rdesc->enable_time; + +/* parse volt_table */ + + rdesc->n_voltages =of_property_count_u32_elems (np,"voltage-table" ); + + v_table =devm_kzalloc (dev,sizeof (unsigned int ) * rdesc->n_voltages, +GFP_KERNEL ); +if (unlikely (!v_table)) +return -ENOMEM ; + rdesc->volt_table = v_table; + + ret =of_property_read_u32_array (np,"voltage-table" , + v_table, rdesc->n_voltages); +if (ret) { +dev_err (dev,"missing voltage-table property\n" ); +return ret; + } + +/* +* Instead of explicitly requiring a mask for the voltage selector, +* as they all start from bit zero (at least on the known LDOs), +* just use the number of voltages at the voltage table, getting the +* minimal mask that would pick everything. +*/ + rdesc->vsel_mask = (1 << (fls (rdesc->n_voltages) -1 )) -1 ; + +dev_dbg (dev,"voltage selector settings: reg: 0x%x, mask: 0x%x" , + rdesc->vsel_reg, rdesc->vsel_mask); + +return 0 ; +} + +static struct regulator_ops hi6421_spmi_ldo_rops = { + .is_enabled = hi6421_spmi_regulator_is_enabled, + .enable = hi6421_spmi_regulator_enable, + .disable = hi6421_spmi_regulator_disable, + .list_voltage = regulator_list_voltage_table,
drivers/regulator/hi6421v600-regulator.c line 331
Quoted 10 lines
drivers/regulator/hi6421v600-regulator.c new file +10
-0+ .map_voltage = regulator_map_voltage_iterate, + .get_voltage_sel = hi6421_spmi_regulator_get_voltage_sel, + .set_voltage_sel = hi6421_spmi_regulator_set_voltage_sel, + .get_mode = hi6421_spmi_regulator_get_mode, + .set_mode = hi6421_spmi_regulator_set_mode, + .get_optimum_mode = hi6421_spmi_regulator_get_optimum_mode, +}; + +/* +* Used only for parsing the DT properties
Odd comment. Clearly does more than that.
drivers/regulator/hi6421v600-regulator.c line 341
Quoted 10 lines
drivers/regulator/hi6421v600-regulator.c new file +10
-0+*/ + +static int hi6421_spmi_regulator_probe_ldo (struct platform_device *pdev, +struct device_node *np, +struct hi6421_spmi_pmic *pmic) +{ +struct device *dev = &pdev->dev; +struct regulator_desc *rdesc; +struct regulator_dev *rdev; +struct hi6421v600_regulator *sreg =NULL ;
Always set.
drivers/regulator/hi6421v600-regulator.c line 346
Quoted 5 lines
drivers/regulator/hi6421v600-regulator.c new file +5
-0+struct regulator_init_data *initdata; +struct regulator_config config = { }; +struct regulation_constraints *constraint; +const char *supplyname =NULL ; +int ret =0 ;
Always set I think
Quoted 46 lines
drivers/regulator/hi6421v600-regulator.c new file +45
-0+ + initdata =of_get_regulator_init_data (dev, np,NULL ); +if (!initdata) { +dev_err (dev,"failed to get regulator data\n" ); +return -EINVAL ; + } + + sreg =kzalloc (sizeof (*sreg),GFP_KERNEL ); +if (!sreg) +return -ENOMEM ; + + sreg->pmic = pmic; + rdesc = &sreg->rdesc; + + rdesc->name = initdata->constraints.name; + rdesc->ops = &hi6421_spmi_ldo_rops; + rdesc->type =REGULATOR_VOLTAGE ; + rdesc->min_uV = initdata->constraints.min_uV; + + supplyname =of_get_property (np,"supply_name" ,NULL ); +if (supplyname) + initdata->supply_regulator = supplyname; + +/* parse device tree data for regulator specific */ + ret =hi6421_spmi_dt_parse (pdev, sreg, rdesc); +if (ret) + goto probe_end; + +/* hisi regulator supports two modes */ + constraint = &initdata->constraints; + + constraint->valid_modes_mask =REGULATOR_MODE_NORMAL ; +if (sreg->eco_mode_mask) { + constraint->valid_modes_mask |=REGULATOR_MODE_IDLE ; + constraint->valid_ops_mask |=REGULATOR_CHANGE_MODE ; + } + + config.dev = &pdev->dev; + config.init_data = initdata; + config.driver_data = sreg; + config.of_node = pdev->dev.of_node; + +/* register regulator */ + rdev =regulator_register (rdesc, &config); +if (IS_ERR (rdev)) {
drivers/regulator/hi6421v600-regulator.c line 401
Quoted 10 lines
drivers/regulator/hi6421v600-regulator.c new file +10
-0+dev_err (dev,"failed to register %s\n" , + rdesc->name); + ret =PTR_ERR (rdev); + goto probe_end; + } + +rdev_dbg (rdev,"valid_modes_mask: 0x%x, valid_ops_mask: 0x%x\n" , + constraint->valid_modes_mask, constraint->valid_ops_mask); + +dev_set_drvdata (dev, rdev);
I'd do separate error path.
return 0;
drivers/regulator/hi6421v600-regulator.c line 403
Quoted 2 lines
drivers/regulator/hi6421v600-regulator.c new file +2
-0+probe_end: +if (ret)
ret is set if separate error path.
I haven't figured out lifetime but can we not use devm for sreg?
Quoted 4 lines
drivers/regulator/hi6421v600-regulator.c new file +4
-0+kfree (sreg); +return ret; +} +
drivers/regulator/hi6421v600-regulator.c line 417
Quoted 10 lines
drivers/regulator/hi6421v600-regulator.c new file +10
-0+static int hi6421_spmi_regulator_probe (struct platform_device *pdev) +{ +struct device *pmic_dev = pdev->dev.parent; +struct device_node *np = pmic_dev->of_node; +struct device_node *regulators, *child; +struct platform_device *new_pdev; +struct hi6421_spmi_pmic *pmic; +int ret; + +dev_dbg (&pdev->dev,"probing hi6421v600 regulator\n" );
Noise.
Quoted 39 lines
drivers/regulator/hi6421v600-regulator.c new file +39
-0+/* +* This driver is meant to be called by hi6421-spmi-core, +* which should first set drvdata. If this doesn't happen, hit +* a warn on and return. +*/ + pmic =dev_get_drvdata (pmic_dev); +if (WARN_ON (!pmic)) +return -ENODEV ; + + regulators =of_get_child_by_name (np,"regulators" ); +if (!regulators) { +dev_err (&pdev->dev,"regulator node not found\n" ); +return -ENODEV ; + } + +/* +* Parse all LDO regulator nodes +*/ +for_each_child_of_node (regulators, child) { +dev_dbg (&pdev->dev,"adding child %pOF\n" , child); + + new_pdev =platform_device_alloc (child->name,-1 ); + new_pdev->dev.parent = pmic_dev; + new_pdev->dev.of_node =of_node_get (child); + + ret =platform_device_add (new_pdev); +if (ret <0 ) { +platform_device_put (new_pdev); +continue ; + } + + ret =hi6421_spmi_regulator_probe_ldo (new_pdev, child, pmic); +if (ret <0 ) +platform_device_put (new_pdev); + } + +of_node_put (regulators); + +return 0 ;
drivers/regulator/hi6421v600-regulator.c line 466
Quoted 10 lines
drivers/regulator/hi6421v600-regulator.c new file +10
-0+} + +static int hi6421_spmi_regulator_remove (struct platform_device *pdev) +{ +struct regulator_dev *rdev =dev_get_drvdata (&pdev->dev); +struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev); + +regulator_unregister (rdev); + +/* TODO: should i worry about that? devm_kzalloc */
Answer that TODO. No unless something odd going on.
drivers/regulator/hi6421v600-regulator.c line 470
Quoted 4 lines
drivers/regulator/hi6421v600-regulator.c new file +4
-0+if (rdev->desc->volt_table) +devm_kfree (&pdev->dev, (unsigned int *)rdev->desc->volt_table); + +kfree (sreg);
This is a worrying mix of devm and not. Never a good sign. Lifetime of sreg seems strange.
Quoted 28 lines
drivers/regulator/hi6421v600-regulator.c new file +23
-0+ +return 0 ; +} + +static const struct platform_device_id hi6421v600_regulator_table[] = { + { .name ="hi6421v600-regulator" }, + {}, +}; +MODULE_DEVICE_TABLE (platform, hi6421v600_regulator_table); + +static struct platform_driver hi6421v600_regulator_driver = { + .id_table = hi6421v600_regulator_table, + .driver = { + .name ="hi6421v600-regulator" , + }, + .probe = hi6421_spmi_regulator_probe, + .remove = hi6421_spmi_regulator_remove, +}; +module_platform_driver (hi6421v600_regulator_driver); + +MODULE_DESCRIPTION ("Hi6421v600 regulator driver" ); +MODULE_LICENSE ("GPL v2" ); +drivers/spmi/Kconfig +0
-0
drivers/spmi/Kconfig config SPMI_MSM_PMIC_ARB · line 31
Quoted 7 lines
drivers/spmi/Kconfig +4
-0@@ -25,4 +25,13 @@ config SPMI_MSM_PMIC_ARB This is required for communicating with Qualcomm PMICs and other devices that have the SPMI interface. +config SPMI_HISI3670 + tristate "Hisilicon 3670 SPMI Controller" + select IRQ_DOMAIN_HIERARCHY + depends on HAS_IOMEM
I have a vague recollection some magic was done to mean we don't need that any more (stubs for the few cases where it doesn't exist). Could have remembered wrong though.
Quoted 22 lines
drivers/spmi/Kconfig +5
-0+ help + If you say yes to this option, support will be included for the + built-in SPMI PMIC Arbiter interface on Hisilicon 3670 + processors. + endifdrivers/spmi/Makefile +2
-0@@ -5,3 +5,5 @@ obj-$(CONFIG_SPMI) += spmi.o obj-$(CONFIG_SPMI_MSM_PMIC_ARB) += spmi-pmic-arb.o + +obj-$(CONFIG_SPMI_HISI3670) += hisi-spmi-controller.odrivers/spmi/hisi-spmi-controller.c new file +0
-0
drivers/spmi/hisi-spmi-controller.c line 2
Quoted 2 lines
drivers/spmi/hisi-spmi-controller.c new file +2
-0@@ -0,0 +1,384 @@ +// SPDX-License-Identifier: GPL-2.0 +
I don't know much about spmi so this is very much a drive by review.
drivers/spmi/hisi-spmi-controller.c line 13
Quoted 11 lines
drivers/spmi/hisi-spmi-controller.c new file +11
-0+#include <linux/delay.h> +#include <linux/err.h> +#include <linux/io.h> +#include <linux/kernel.h> +#include <linux/platform_device.h> +#include <linux/slab.h> +#include <linux/of.h> +#include <linux/interrupt.h> +#include <linux/module.h> +#include <linux/seq_file.h> +#include <linux/spmi.h>
Nice to do alphabetical if no reason to do otherwise.
drivers/spmi/hisi-spmi-controller.c line 15
Quoted 2 lines
drivers/spmi/hisi-spmi-controller.c new file +2
-0+ +#define SPMI_CONTROLLER_NAME "spmi_controller"
Feels like we should have hisi in there. Also should prefix naming throughout with HISI_SPMI
Quoted 51 lines
drivers/spmi/hisi-spmi-controller.c new file +51
-0+ +/* +* SPMI register addr +*/ +#define SPMI_CHANNEL_OFFSET 0x0300 +#define SPMI_SLAVE_OFFSET 0x20 + +#define SPMI_APB_SPMI_CMD_BASE_ADDR 0x0100 + +#define SPMI_APB_SPMI_WDATA0_BASE_ADDR 0x0104 +#define SPMI_APB_SPMI_WDATA1_BASE_ADDR 0x0108 +#define SPMI_APB_SPMI_WDATA2_BASE_ADDR 0x010c +#define SPMI_APB_SPMI_WDATA3_BASE_ADDR 0x0110 + +#define SPMI_APB_SPMI_STATUS_BASE_ADDR 0x0200 + +#define SPMI_APB_SPMI_RDATA0_BASE_ADDR 0x0204 +#define SPMI_APB_SPMI_RDATA1_BASE_ADDR 0x0208 +#define SPMI_APB_SPMI_RDATA2_BASE_ADDR 0x020c +#define SPMI_APB_SPMI_RDATA3_BASE_ADDR 0x0210 + +#define SPMI_PER_DATAREG_BYTE 4 +/* +* SPMI cmd register +*/ +#define SPMI_APB_SPMI_CMD_EN BIT(31) +#define SPMI_APB_SPMI_CMD_TYPE_OFFSET 24 +#define SPMI_APB_SPMI_CMD_LENGTH_OFFSET 20 +#define SPMI_APB_SPMI_CMD_SLAVEID_OFFSET 16 +#define SPMI_APB_SPMI_CMD_ADDR_OFFSET 0 + +/* Command Opcodes */ + +enum spmi_controller_cmd_op_code { +SPMI_CMD_REG_ZERO_WRITE =0 , +SPMI_CMD_REG_WRITE =1 , +SPMI_CMD_REG_READ =2 , +SPMI_CMD_EXT_REG_WRITE =3 , +SPMI_CMD_EXT_REG_READ =4 , +SPMI_CMD_EXT_REG_WRITE_L =5 , +SPMI_CMD_EXT_REG_READ_L =6 , +SPMI_CMD_REG_RESET =7 , +SPMI_CMD_REG_SLEEP =8 , +SPMI_CMD_REG_SHUTDOWN =9 , +SPMI_CMD_REG_WAKEUP =10 , +}; + +/* +* SPMI status register +*/ +#define SPMI_APB_TRANS_DONE BIT(0)
drivers/spmi/hisi-spmi-controller.c line 76
Quoted 10 lines
drivers/spmi/hisi-spmi-controller.c new file +10
-0+#define SPMI_APB_TRANS_FAIL BIT(2) + +/* Command register fields */ +#define SPMI_CONTROLLER_CMD_MAX_BYTE_COUNT 16 + +/* Maximum number of support PMIC peripherals */ +#define SPMI_CONTROLLER_TIMEOUT_US 1000 +#define SPMI_CONTROLLER_MAX_TRANS_BYTES 16 + +/*
Nice to make this both correct kernel doc and reflect the structure I assume it is documenting.
Quoted 23 lines
drivers/spmi/hisi-spmi-controller.c new file +23
-0+* @base base address of the PMIC Arbiter core registers. +* @rdbase, @wrbase base address of the PMIC Arbiter read core registers. +* For HW-v1 these are equal to base. +* For HW-v2, the value is the same in eeraly probing, in order to read +* PMIC_ARB_CORE registers, then chnls, and obsrvr are set to +* PMIC_ARB_CORE_REGISTERS and PMIC_ARB_CORE_REGISTERS_OBS respectivly. +* @intr base address of the SPMI interrupt control registers +* @ppid_2_chnl_tbl lookup table f(SID, Periph-ID) -> channel num +* entry is only valid if corresponding bit is set in valid_ppid_bitmap. +* @valid_ppid_bitmap bit is set only for valid ppids. +* @fmt_cmd formats a command to be set into PMIC_ARBq_CHNLn_CMD +* @chnl_ofst calculates offset of the base of a channel reg space +* @ee execution environment id +* @irq_acc0_init_val initial value of the interrupt accumulator at probe time. +* Use for an HW workaround. On handling interrupts, the first accumulator +* register will be compared against this value, and bits which are set at +* boot will be ignored. +* @reserved_chnl entry of ppid_2_chnl_tbl that this driver should never touch. +* value is positive channel number or negative to mark it unused. +*/ +struct spmi_controller_dev { +struct spmi_controller *controller; +struct device *dev;
drivers/spmi/hisi-spmi-controller.c line 109
Quoted 10 lines
drivers/spmi/hisi-spmi-controller.c new file +10
-0+void __iomem *base; +spinlock_t lock; +u32 channel; +}; + +static int spmi_controller_wait_for_done (struct device *dev, +struct spmi_controller_dev *ctrl_dev, +void __iomem *base,u8 sid,u16 addr) +{ +u32 status =0 ;
always set.
Quoted 18 lines
drivers/spmi/hisi-spmi-controller.c new file +18
-0+u32 timeout =SPMI_CONTROLLER_TIMEOUT_US ; +u32 offset; + + offset =SPMI_APB_SPMI_STATUS_BASE_ADDR ; + offset +=SPMI_CHANNEL_OFFSET * ctrl_dev->channel +SPMI_SLAVE_OFFSET * sid; + +while (timeout--) { + status =readl (base + offset); + +if (status &SPMI_APB_TRANS_DONE ) { +if (status &SPMI_APB_TRANS_FAIL ) { +dev_err (dev,"%s: transaction failed (0x%x)\n" , + __func__, status); +return -EIO ; + } +dev_dbg (dev,"%s: status 0x%x\n" , __func__, status); +return 0 ; + }
drivers/spmi/hisi-spmi-controller.c line 137
Quoted 10 lines
drivers/spmi/hisi-spmi-controller.c new file +10
-0+udelay (1 ); + } + +dev_err (dev,"%s: timeout, status 0x%x\n" , __func__, status); +return -ETIMEDOUT ; +} + +static int spmi_read_cmd (struct spmi_controller *ctrl, +u8 opc,u8 sid,u16 addr,u8 *__buf,size_t bc) +{
Same stuff as for the write below.
Quoted 78 lines
drivers/spmi/hisi-spmi-controller.c new file +78
-0+struct spmi_controller_dev *spmi_controller =dev_get_drvdata (&ctrl->dev); +unsigned long flags; +u8 *buf = __buf; +u32 cmd, data; +int rc; +u32 chnl_ofst =SPMI_CHANNEL_OFFSET * spmi_controller->channel; +u8 op_code, i; + +if (bc >SPMI_CONTROLLER_MAX_TRANS_BYTES ) { +dev_err (&ctrl->dev, +"spmi_controller supports 1..%d bytes per trans, but:%ld requested" , +SPMI_CONTROLLER_MAX_TRANS_BYTES , bc); +return -EINVAL ; + } + +/* Check the opcode */ +if (opc ==SPMI_CMD_READ ) { + op_code =SPMI_CMD_REG_READ ; + }else if (opc ==SPMI_CMD_EXT_READ ) { + op_code =SPMI_CMD_EXT_REG_READ ; + }else if (opc ==SPMI_CMD_EXT_READL ) { + op_code =SPMI_CMD_EXT_REG_READ_L ; + }else { +dev_err (&ctrl->dev,"invalid read cmd 0x%x" , opc); +return -EINVAL ; + } + + cmd =SPMI_APB_SPMI_CMD_EN | + (op_code <<SPMI_APB_SPMI_CMD_TYPE_OFFSET ) | + ((bc -1 ) <<SPMI_APB_SPMI_CMD_LENGTH_OFFSET ) | + ((sid &0xf ) <<SPMI_APB_SPMI_CMD_SLAVEID_OFFSET ) |/* slvid */ + ((addr &0xffff ) <<SPMI_APB_SPMI_CMD_ADDR_OFFSET );/* slave_addr */ + +spin_lock_irqsave (&spmi_controller->lock, flags); + +writel (cmd, spmi_controller->base + chnl_ofst +SPMI_APB_SPMI_CMD_BASE_ADDR ); + + rc =spmi_controller_wait_for_done (&ctrl->dev, spmi_controller, + spmi_controller->base, sid, addr); +if (rc) + goto done; + + i =0 ; +do { + data =readl (spmi_controller->base + chnl_ofst +SPMI_SLAVE_OFFSET * sid +SPMI_APB_SPMI_RDATA0_BASE_ADDR + i *SPMI_PER_DATAREG_BYTE ); + data =be32_to_cpu ((__be32 )data); +if ((bc - i *SPMI_PER_DATAREG_BYTE ) >>2 ) { +memcpy (buf, &data,sizeof (data)); + buf +=sizeof (data); + }else { +memcpy (buf, &data, bc %SPMI_PER_DATAREG_BYTE ); + buf += (bc %SPMI_PER_DATAREG_BYTE ); + } + i++; + }while (bc > i *SPMI_PER_DATAREG_BYTE ); + +done: +spin_unlock_irqrestore (&spmi_controller->lock, flags); +if (rc) +dev_err (&ctrl->dev, +"spmi read wait timeout op:0x%x sid:%d addr:0x%x bc:%ld\n" , + opc, sid, addr, bc +1 ); +else +dev_dbg (&ctrl->dev,"%s: id:%d addr:0x%x, read value: %*ph\n" , + __func__, sid, addr, (int )bc, __buf); + +return rc; +} + +static int spmi_write_cmd (struct spmi_controller *ctrl, +u8 opc,u8 sid,u16 addr,const u8 *__buf,size_t bc) +{ +struct spmi_controller_dev *spmi_controller =dev_get_drvdata (&ctrl->dev); +const u8 *buf = __buf; +unsigned long flags; +u32 cmd, data; +int rc; +u32 chnl_ofst =SPMI_CHANNEL_OFFSET * spmi_controller->channel;
drivers/spmi/hisi-spmi-controller.c line 225
Quoted 10 lines
drivers/spmi/hisi-spmi-controller.c new file +10
-0+u8 op_code, i; + +if (bc >SPMI_CONTROLLER_MAX_TRANS_BYTES ) { +dev_err (&ctrl->dev, +"spmi_controller supports 1..%d bytes per trans, but:%ld requested" , +SPMI_CONTROLLER_MAX_TRANS_BYTES , bc); +return -EINVAL ; + } + +/* Check the opcode */
Kind of obvious given the code :)
drivers/spmi/hisi-spmi-controller.c line 231
Quoted 6 lines
drivers/spmi/hisi-spmi-controller.c new file +6
-0+if (opc ==SPMI_CMD_WRITE ) { + op_code =SPMI_CMD_REG_WRITE ; + }else if (opc ==SPMI_CMD_EXT_WRITE ) { + op_code =SPMI_CMD_EXT_REG_WRITE ; + }else if (opc ==SPMI_CMD_EXT_WRITEL ) { + op_code =SPMI_CMD_EXT_REG_WRITE_L ;
Looks like something better expressed as a switch statement to me.
drivers/spmi/hisi-spmi-controller.c line 241
Quoted 10 lines
drivers/spmi/hisi-spmi-controller.c new file +10
-0+ }else { +dev_err (&ctrl->dev,"invalid write cmd 0x%x" , opc); +return -EINVAL ; + } + + cmd =SPMI_APB_SPMI_CMD_EN | + (op_code <<SPMI_APB_SPMI_CMD_TYPE_OFFSET ) | + ((bc -1 ) <<SPMI_APB_SPMI_CMD_LENGTH_OFFSET ) | + ((sid &0xf ) <<SPMI_APB_SPMI_CMD_SLAVEID_OFFSET ) |/* slvid */ + ((addr &0xffff ) <<SPMI_APB_SPMI_CMD_ADDR_OFFSET );/* slave_addr */
Those two comments pretty clearly highlight that names of variables could be better.
could we use FIELD_PREP and friends to do this more neatly?
Quoted 23 lines
drivers/spmi/hisi-spmi-controller.c new file +23
-0+ +/* Write data to FIFOs */ +spin_lock_irqsave (&spmi_controller->lock, flags); + + i =0 ; +do { + data =0 ; +if ((bc - i *SPMI_PER_DATAREG_BYTE ) >>2 ) { +memcpy (&data, buf,sizeof (data)); + buf +=sizeof (data); + }else { +memcpy (&data, buf, bc %SPMI_PER_DATAREG_BYTE ); + buf += (bc %SPMI_PER_DATAREG_BYTE ); + } + +writel ((u32 )cpu_to_be32 (data), + spmi_controller->base + chnl_ofst +SPMI_APB_SPMI_WDATA0_BASE_ADDR +SPMI_PER_DATAREG_BYTE * i); + i++; + }while (bc > i *SPMI_PER_DATAREG_BYTE ); + +/* Start the transaction */ +writel (cmd, spmi_controller->base + chnl_ofst +SPMI_APB_SPMI_CMD_BASE_ADDR ); +
drivers/spmi/hisi-spmi-controller.c line 274
Quoted 10 lines
drivers/spmi/hisi-spmi-controller.c new file +10
-0+ rc =spmi_controller_wait_for_done (&ctrl->dev, spmi_controller, + spmi_controller->base, sid, addr); +spin_unlock_irqrestore (&spmi_controller->lock, flags); + +if (rc) +dev_err (&ctrl->dev,"spmi write wait timeout op:0x%x sid:%d addr:0x%x bc:%ld\n" , + opc, sid, addr, bc); +else +dev_dbg (&ctrl->dev,"%s: id:%d addr:0x%x, wrote value: %*ph\n" , + __func__, sid, addr, (int )bc, __buf);
I'd drop the debug. Adds a lot of code for limited benefit.
drivers/spmi/hisi-spmi-controller.c line 284
Quoted 10 lines
drivers/spmi/hisi-spmi-controller.c new file +10
-0+ +return rc; +} + +static int spmi_controller_probe (struct platform_device *pdev) +{ +struct spmi_controller_dev *spmi_controller; +struct spmi_controller *ctrl; +struct resource *iores; +int ret =0 ;
Fairly sure that's set in all paths.
drivers/spmi/hisi-spmi-controller.c line 286
Quoted 2 lines
drivers/spmi/hisi-spmi-controller.c new file +2
-0+ +dev_info (&pdev->dev,"HISI SPMI probe\n" );
Too noisy
drivers/spmi/hisi-spmi-controller.c line 288
Quoted 2 lines
drivers/spmi/hisi-spmi-controller.c new file +2
-0+ + ctrl =spmi_controller_alloc (&pdev->dev,sizeof (*spmi_controller));
We don't seem to clean this up in failure paths.
drivers/spmi/hisi-spmi-controller.c line 296
Quoted 8 lines
drivers/spmi/hisi-spmi-controller.c new file +8
-0+if (!ctrl) { +dev_err (&pdev->dev,"can not allocate spmi_controller data\n" ); +return -ENOMEM ; + } + spmi_controller =spmi_controller_get_drvdata (ctrl); + spmi_controller->controller = ctrl; + +/* NOTE: driver uses the static register mapping */
Do we need to Note it for some reason I'm not seeing?
drivers/spmi/hisi-spmi-controller.c line 309
Quoted 13 lines
drivers/spmi/hisi-spmi-controller.c new file +13
-0+ iores =platform_get_resource (pdev,IORESOURCE_MEM ,0 ); +if (!iores) { +dev_err (&pdev->dev,"can not get resource!\n" ); +return -EINVAL ; + } + + spmi_controller->base =ioremap (iores->start,resource_size (iores)); +if (!spmi_controller->base) { +dev_err (&pdev->dev,"can not remap base addr!\n" ); +return -EADDRNOTAVAIL ; + } +dev_dbg (&pdev->dev,"spmi_add_controller base addr=0x%lx!\n" , + (unsigned long )spmi_controller->base);
I doubt that one is ever of any use to anyone after initial driver writing. I'd drop it.
drivers/spmi/hisi-spmi-controller.c line 311
Quoted 2 lines
drivers/spmi/hisi-spmi-controller.c new file +2
-0+ +/* Get properties from the device tree */
Comment doesn't add anything
Quoted 15 lines
drivers/spmi/hisi-spmi-controller.c new file +15
-0+ ret =of_property_read_u32 (pdev->dev.of_node,"spmi-channel" , + &spmi_controller->channel); +if (ret) { +dev_err (&pdev->dev,"can not get channel\n" ); +return -ENODEV ; + } + +platform_set_drvdata (pdev, spmi_controller); +dev_set_drvdata (&ctrl->dev, spmi_controller); + +spin_lock_init (&spmi_controller->lock); + + ctrl->nr = spmi_controller->channel; + ctrl->dev.parent = pdev->dev.parent; + ctrl->dev.of_node =of_node_get (pdev->dev.of_node);
drivers/spmi/hisi-spmi-controller.c line 336
Quoted 10 lines
drivers/spmi/hisi-spmi-controller.c new file +10
-0+ +/* Callbacks */ + ctrl->read_cmd = spmi_read_cmd; + ctrl->write_cmd = spmi_write_cmd; + + ret =spmi_controller_add (ctrl); +if (ret) + goto err_add_controller; + +dev_info (&pdev->dev,"spmi_add_controller initialized\n" );
Too noisy.
drivers/spmi/hisi-spmi-controller.c line 340
Quoted 4 lines
drivers/spmi/hisi-spmi-controller.c new file +4
-0+return 0 ; + +err_add_controller: +dev_err (&pdev->dev,"spmi_add_controller failed!\n" );
Seems too noisy to me given information provided is minimal.
drivers/spmi/hisi-spmi-controller.c line 341
Quoted 1 line
drivers/spmi/hisi-spmi-controller.c new file +1
-0+platform_set_drvdata (pdev,NULL );
not needed.
drivers/spmi/hisi-spmi-controller.c line 342
Quoted 1 line
drivers/spmi/hisi-spmi-controller.c new file +1
-0+return ret;
Use direct returns if not cleaning anything up... THough see above, there are things that I'm fairly sure you should be!
drivers/spmi/hisi-spmi-controller.c line 349
Quoted 7 lines
drivers/spmi/hisi-spmi-controller.c new file +7
-0+} + +static int spmi_del_controller (struct platform_device *pdev) +{ +struct spmi_controller *ctrl =platform_get_drvdata (pdev); + +platform_set_drvdata (pdev,NULL );
Doubt you need that. Core sets it to null on remove or error.
drivers/spmi/hisi-spmi-controller.c line 350
Quoted 1 line
drivers/spmi/hisi-spmi-controller.c new file +1
-0+spmi_controller_remove (ctrl);
It's asking for a devm_spmi_controller_add. or just go with devm_add_action_or_reset perhaps.
drivers/spmi/spmi.c
Quoted 38 lines
drivers/spmi/hisi-spmi-controller.c new file +34
-0+return 0 ; +} + +static const struct of_device_id spmi_controller_match_table[] = { + { .compatible ="hisilicon,spmi-controller" , + }, + {} +}; +MODULE_DEVICE_TABLE (of, spmi_controller_match_table); + +static struct platform_driver spmi_controller_driver = { + .probe = spmi_controller_probe, + .remove = spmi_del_controller, + .driver = { + .name =SPMI_CONTROLLER_NAME , + .of_match_table = spmi_controller_match_table, + }, +}; + +static int __init spmi_controller_init (void ) +{ +return platform_driver_register (&spmi_controller_driver); +} +postcore_initcall (spmi_controller_init); + +static void __exit spmi_controller_exit(void) +{ +platform_driver_unregister (&spmi_controller_driver); +} +module_exit (spmi_controller_exit); + +MODULE_LICENSE ("GPL v2" ); +MODULE_VERSION ("1.0" ); +MODULE_ALIAS ("platform:spmi_controlller" );drivers/spmi/spmi.c +0
-0
All the changes in here look to be cleanup. Drop it from this series as it just adds noise.
Quoted 48 lines
drivers/spmi/spmi.c +5
-5@@ -23,6 +23,7 @@ static DEFINE_IDA(ctrl_ida);static void spmi_dev_release (struct device *dev) {struct spmi_device *sdev =to_spmi_device (dev); +kfree (sdev); }@@ -33,6 +34,7 @@ static const struct device_type spmi_dev_type = {static void spmi_ctrl_release (struct device *dev) {struct spmi_controller *ctrl =to_spmi_controller (dev); +ida_simple_remove (&ctrl_ida, ctrl->nr);kfree (ctrl); }@@ -487,7 +489,7 @@ static void of_spmi_register_devices(struct spmi_controller *ctrl)continue ; sdev->dev.of_node = node; - sdev->usid = (u8 ) reg[0 ]; + sdev->usid = (u8 )reg[0 ]; err =spmi_device_add (sdev);if (err) {@@ -531,6 +533,7 @@ EXPORT_SYMBOL_GPL(spmi_controller_add);static int spmi_ctrl_remove_device (struct device *dev,void *data) {struct spmi_device *spmidev =to_spmi_device (dev); +if (dev->type == &spmi_dev_type)spmi_device_remove (spmidev);return 0 ;@@ -545,13 +548,10 @@ static int spmi_ctrl_remove_device(struct device *dev, void *data)*/ void spmi_controller_remove (struct spmi_controller *ctrl) { -int dummy; -if (!ctrl)return ; - dummy =device_for_each_child (&ctrl->dev,NULL , - spmi_ctrl_remove_device); +device_for_each_child (&ctrl->dev,NULL , spmi_ctrl_remove_device);device_del (&ctrl->dev); }EXPORT_SYMBOL_GPL (spmi_controller_remove);
kernel test robot
build botRe: [PATCH 14/33] spmi: add hisi-spmi-controller to the building system
In reply to Mauro Carvalho ChehabI love your patch! Perhaps something to improve:
Hi Mauro,
I love your patch! Perhaps something to improve:
[auto build test WARNING on lee-mfd/for-mfd-next]
[also build test WARNING on regulator/for-next robh/for-next linus/master v5.8 next-20200811] [If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]
url: https://github.com/0day-ci/linux/commits/Mauro-Carvalho-Chehab/Add-driver-for-HiSilicon-SPMI-PMIC-for-Hikey-970/20200811-234737 base: https://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git for-mfd-next config: arc-allyesconfig (attached as .config) compiler: arc-elf-gcc (GCC) 9.3.0
reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross chmod +x ~/bin/make.cross
# save the attached .config to linux build tree
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-9.3.0 make.cross ARCH=arc
If you fix the issue, kindly add following tag as appropriate
All warnings (new ones prefixed by >>):
In file included from include/linux/device.h:15,
from include/linux/platform_device.h:13, from drivers/spmi/hisi-spmi-controller.c:7:
drivers/spmi/hisi-spmi-controller.c: In function 'spmi_read_cmd':
>> drivers/spmi/hisi-spmi-controller.c:149:5: warning: format '%ld' expects argument of type 'long int', but argument 4 has type 'size_t' {aka 'unsigned int'} [-Wformat=]
149 | , "spmi_controller supports 1..%d bytes per trans, but:%ld requested"
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/dev_printk.h:19:22: note: in definition of macro 'dev_fmt'
19 | #define dev_fmt(fmt) fmt
| ^~~
drivers/spmi/hisi-spmi-controller.c:148:3: note: in expansion of macro 'dev_err'
148 | dev_err(spmi_controller->dev
| ^~~~~~~
drivers/spmi/hisi-spmi-controller.c:149:60: note: format string is defined here
149 | , "spmi_controller supports 1..%d bytes per trans, but:%ld requested"
| ~~^
| |
| long int
| %d
In file included from include/linux/device.h:15,
from include/linux/platform_device.h:13,
from drivers/spmi/hisi-spmi-controller.c:7:
drivers/spmi/hisi-spmi-controller.c:198:33: warning: format '%ld' expects argument of type 'long int', but argument 6 has type 'size_t' {aka 'unsigned int'} [-Wformat=]
198 | dev_err(spmi_controller->dev, "spmi read wait timeout op:0x%x sid:%d addr:0x%x bc:%ld\n",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/dev_printk.h:19:22: note: in definition of macro 'dev_fmt'
19 | #define dev_fmt(fmt) fmt
| ^~~
drivers/spmi/hisi-spmi-controller.c:198:3: note: in expansion of macro 'dev_err'
198 | dev_err(spmi_controller->dev, "spmi read wait timeout op:0x%x sid:%d addr:0x%x bc:%ld\n",
| ^~~~~~~
drivers/spmi/hisi-spmi-controller.c:198:87: note: format string is defined here
198 | dev_err(spmi_controller->dev, "spmi read wait timeout op:0x%x sid:%d addr:0x%x bc:%ld\n",
| ~~^
| |
| long int
| %d
In file included from include/linux/device.h:15,
from include/linux/platform_device.h:13,
from drivers/spmi/hisi-spmi-controller.c:7:
drivers/spmi/hisi-spmi-controller.c: In function 'spmi_write_cmd':
drivers/spmi/hisi-spmi-controller.c:220:5: warning: format '%ld' expects argument of type 'long int', but argument 4 has type 'size_t' {aka 'unsigned int'} [-Wformat=]
220 | , "spmi_controller supports 1..%d bytes per trans, but:%ld requested"
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/dev_printk.h:19:22: note: in definition of macro 'dev_fmt'
19 | #define dev_fmt(fmt) fmt
| ^~~
drivers/spmi/hisi-spmi-controller.c:219:3: note: in expansion of macro 'dev_err'
219 | dev_err(spmi_controller->dev
| ^~~~~~~
drivers/spmi/hisi-spmi-controller.c:220:60: note: format string is defined here
220 | , "spmi_controller supports 1..%d bytes per trans, but:%ld requested"
| ~~^
| |
| long int
| %d
In file included from include/linux/device.h:15,
from include/linux/platform_device.h:13,
from drivers/spmi/hisi-spmi-controller.c:7:
drivers/spmi/hisi-spmi-controller.c:269:33: warning: format '%ld' expects argument of type 'long int', but argument 6 has type 'size_t' {aka 'unsigned int'} [-Wformat=]
269 | dev_err(spmi_controller->dev, "spmi write wait timeout op:0x%x sid:%d addr:0x%x bc:%ld\n",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/dev_printk.h:19:22: note: in definition of macro 'dev_fmt'
19 | #define dev_fmt(fmt) fmt
| ^~~
drivers/spmi/hisi-spmi-controller.c:269:3: note: in expansion of macro 'dev_err'
269 | dev_err(spmi_controller->dev, "spmi write wait timeout op:0x%x sid:%d addr:0x%x bc:%ld\n",
| ^~~~~~~
drivers/spmi/hisi-spmi-controller.c:269:88: note: format string is defined here
269 | dev_err(spmi_controller->dev, "spmi write wait timeout op:0x%x sid:%d addr:0x%x bc:%ld\n",
| ~~^
| |
| long int
| %dvim +149 drivers/spmi/hisi-spmi-controller.c
3f5f1801bf6c4a3 Mayulong 2020-08-11 135
3f5f1801bf6c4a3 Mayulong 2020-08-11 136 static int spmi_read_cmd(struct spmi_controller *ctrl,
a93f9ffda101599 Mauro Carvalho Chehab 2020-08-11 137 u8 opc, u8 sid, u16 addr, u8 *__buf, size_t bc)
3f5f1801bf6c4a3 Mayulong 2020-08-11 138 {
3f5f1801bf6c4a3 Mayulong 2020-08-11 139 struct spmi_controller_dev *spmi_controller = dev_get_drvdata(&ctrl->dev);
3f5f1801bf6c4a3 Mayulong 2020-08-11 140 unsigned long flags;
a93f9ffda101599 Mauro Carvalho Chehab 2020-08-11 141 u8 *buf = __buf;
3f5f1801bf6c4a3 Mayulong 2020-08-11 142 u32 cmd, data;
3f5f1801bf6c4a3 Mayulong 2020-08-11 143 int rc;
3f5f1801bf6c4a3 Mayulong 2020-08-11 144 u32 chnl_ofst = SPMI_CHANNEL_OFFSET * spmi_controller->channel;
3f5f1801bf6c4a3 Mayulong 2020-08-11 145 u8 op_code, i;
3f5f1801bf6c4a3 Mayulong 2020-08-11 146
3f5f1801bf6c4a3 Mayulong 2020-08-11 147 if (bc > SPMI_CONTROLLER_MAX_TRANS_BYTES) {
3f5f1801bf6c4a3 Mayulong 2020-08-11 148 dev_err(spmi_controller->dev
3f5f1801bf6c4a3 Mayulong 2020-08-11 @149 , "spmi_controller supports 1..%d bytes per trans, but:%ld requested"
3f5f1801bf6c4a3 Mayulong 2020-08-11 150 , SPMI_CONTROLLER_MAX_TRANS_BYTES, bc);
3f5f1801bf6c4a3 Mayulong 2020-08-11 151 return -EINVAL;
3f5f1801bf6c4a3 Mayulong 2020-08-11 152 }
3f5f1801bf6c4a3 Mayulong 2020-08-11 153
3f5f1801bf6c4a3 Mayulong 2020-08-11 154 /* Check the opcode */
43091a1c2b8d45e Mauro Carvalho Chehab 2020-08-11 155 if (opc == SPMI_CMD_READ) {
3f5f1801bf6c4a3 Mayulong 2020-08-11 156 op_code = SPMI_CMD_REG_READ;
43091a1c2b8d45e Mauro Carvalho Chehab 2020-08-11 157 } else if (opc == SPMI_CMD_EXT_READ) {
3f5f1801bf6c4a3 Mayulong 2020-08-11 158 op_code = SPMI_CMD_EXT_REG_READ;
43091a1c2b8d45e Mauro Carvalho Chehab 2020-08-11 159 } else if (opc == SPMI_CMD_EXT_READL) {
3f5f1801bf6c4a3 Mayulong 2020-08-11 160 op_code = SPMI_CMD_EXT_REG_READ_L;
43091a1c2b8d45e Mauro Carvalho Chehab 2020-08-11 161 } else {
3f5f1801bf6c4a3 Mayulong 2020-08-11 162 dev_err(spmi_controller->dev, "invalid read cmd 0x%x", opc);
3f5f1801bf6c4a3 Mayulong 2020-08-11 163 return -EINVAL;
3f5f1801bf6c4a3 Mayulong 2020-08-11 164 }
3f5f1801bf6c4a3 Mayulong 2020-08-11 165
43091a1c2b8d45e Mauro Carvalho Chehab 2020-08-11 166 cmd = SPMI_APB_SPMI_CMD_EN |
43091a1c2b8d45e Mauro Carvalho Chehab 2020-08-11 167 (op_code << SPMI_APB_SPMI_CMD_TYPE_OFFSET) |
43091a1c2b8d45e Mauro Carvalho Chehab 2020-08-11 168 ((bc - 1) << SPMI_APB_SPMI_CMD_LENGTH_OFFSET) |
3f5f1801bf6c4a3 Mayulong 2020-08-11 169 ((sid & 0xf) << SPMI_APB_SPMI_CMD_SLAVEID_OFFSET) | /* slvid */
3f5f1801bf6c4a3 Mayulong 2020-08-11 170 ((addr & 0xffff) << SPMI_APB_SPMI_CMD_ADDR_OFFSET); /* slave_addr */
3f5f1801bf6c4a3 Mayulong 2020-08-11 171
43091a1c2b8d45e Mauro Carvalho Chehab 2020-08-11 172 spin_lock_irqsave(&spmi_controller->lock, flags);
3f5f1801bf6c4a3 Mayulong 2020-08-11 173
43091a1c2b8d45e Mauro Carvalho Chehab 2020-08-11 174 writel(cmd, spmi_controller->base + chnl_ofst + SPMI_APB_SPMI_CMD_BASE_ADDR);
3f5f1801bf6c4a3 Mayulong 2020-08-11 175
afd5339d05a6fd2 Mauro Carvalho Chehab 2020-08-11 176 rc = spmi_controller_wait_for_done(spmi_controller,
afd5339d05a6fd2 Mauro Carvalho Chehab 2020-08-11 177 spmi_controller->base, sid, addr);
3f5f1801bf6c4a3 Mayulong 2020-08-11 178 if (rc)
3f5f1801bf6c4a3 Mayulong 2020-08-11 179 goto done;
3f5f1801bf6c4a3 Mayulong 2020-08-11 180
3f5f1801bf6c4a3 Mayulong 2020-08-11 181 i = 0;
3f5f1801bf6c4a3 Mayulong 2020-08-11 182 do {
43091a1c2b8d45e Mauro Carvalho Chehab 2020-08-11 183 data = readl(spmi_controller->base + chnl_ofst + SPMI_SLAVE_OFFSET * sid + SPMI_APB_SPMI_RDATA0_BASE_ADDR + i * SPMI_PER_DATAREG_BYTE);
afd5339d05a6fd2 Mauro Carvalho Chehab 2020-08-11 184 data = be32_to_cpu((__be32)data);
43091a1c2b8d45e Mauro Carvalho Chehab 2020-08-11 185 if ((bc - i * SPMI_PER_DATAREG_BYTE) >> 2) {
3f5f1801bf6c4a3 Mayulong 2020-08-11 186 memcpy(buf, &data, sizeof(data));
3f5f1801bf6c4a3 Mayulong 2020-08-11 187 buf += sizeof(data);
3f5f1801bf6c4a3 Mayulong 2020-08-11 188 } else {
43091a1c2b8d45e Mauro Carvalho Chehab 2020-08-11 189 memcpy(buf, &data, bc % SPMI_PER_DATAREG_BYTE);
3f5f1801bf6c4a3 Mayulong 2020-08-11 190 buf += (bc % SPMI_PER_DATAREG_BYTE);
3f5f1801bf6c4a3 Mayulong 2020-08-11 191 }
3f5f1801bf6c4a3 Mayulong 2020-08-11 192 i++;
3f5f1801bf6c4a3 Mayulong 2020-08-11 193 } while (bc > i * SPMI_PER_DATAREG_BYTE);
3f5f1801bf6c4a3 Mayulong 2020-08-11 194
3f5f1801bf6c4a3 Mayulong 2020-08-11 195 done:
3f5f1801bf6c4a3 Mayulong 2020-08-11 196 spin_unlock_irqrestore(&spmi_controller->lock, flags);
3f5f1801bf6c4a3 Mayulong 2020-08-11 197 if (rc)
3f5f1801bf6c4a3 Mayulong 2020-08-11 198 dev_err(spmi_controller->dev, "spmi read wait timeout op:0x%x sid:%d addr:0x%x bc:%ld\n",
3f5f1801bf6c4a3 Mayulong 2020-08-11 199 opc, sid, addr, bc + 1);
a93f9ffda101599 Mauro Carvalho Chehab 2020-08-11 200 else
a93f9ffda101599 Mauro Carvalho Chehab 2020-08-11 201 dev_dbg(spmi_controller->dev, "%s: id:%d addr:0x%x, read value: %*ph\n",
a93f9ffda101599 Mauro Carvalho Chehab 2020-08-11 202 __func__, sid, addr, (int)bc, __buf);
a93f9ffda101599 Mauro Carvalho Chehab 2020-08-11 203
3f5f1801bf6c4a3 Mayulong 2020-08-11 204 return rc;
43091a1c2b8d45e Mauro Carvalho Chehab 2020-08-11 205 }
3f5f1801bf6c4a3 Mayulong 2020-08-11 206 ---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/kbuild-all(a)lists.01.org
Mauro Carvalho Chehab
maintainerEm Tue, 11 Aug 2020 18:51:11 +0100
Jonathan Cameron <[email protected]> escreveu:
Quoted 27 lines
Quoted 24 lines · On Tue, 11 Aug 2020 17:54:29 +0200 Mauro Carvalho Chehab…
Em Tue, 11 Aug 2020 17:41:26 +0200
Mauro Carvalho Chehab <[email protected]> escreveu:Quoted 20 lines
The Hikey 970 board uses a different PMIC than the one found on Hikey 960.
This PMIC uses a SPMI board.
This patch series backport the OOT drivers from the Linaro's official tree for this board:
https://github.com/96boards-hikey/linux/tree/hikey970-v4.9Porting them to upstream, cleaning up coding style issues, solving driver probing order and adding DT documentation.
I opted to not fold all patches into a single one, in order to:
- Preserve the authorship of the original authors;
- Keep a history of changes.As this could be harder for people to review, I'll be replying to patch 00/32 with all patches folded. This should help reviewers to see the current code after the entire series is applied.
Quoted 8 lines
Quoted 5 lines
As promised, it follows the diff from this entire patch series.
Feel free to review either on the top of this e-mail or on the individual patches.
Whilst I agree entirely with Mark about the need to turn this into a clean series, I was bored at the end of the day so here is a drive by review..
Thanks for the review!
Quoted 2 lines
I've not looked at anything that really needed any thought as it is too hot for thinking.
8-)
Quoted 5 lines
Quoted 5 lines
Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml new file +0
-0
...
Quoted 10 lines
Quoted 10 lines
Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml new file +10
-0+ $ref: "/schemas/regulator/regulator.yaml#" + + properties: + reg: + description: Enable register. + + vsel-reg: + description: Voltage selector register. + + enable-mask:
Quoted 8 lines
Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml line 86
Quoted 6 lines
Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml new file +6
-0+ description: Bitmask used to enable the regulator. + +# voltage-table: +# description: Table with the selector items for the voltage regulator. +# minItems: 2 +# maxItems: 16Guess this needs fixing up.
Ah, yeah. Thanks for noticing. I had some troubles with dtbs_check, so I ended commenting out some things for testing purposes. I'll remove the comments and check if this was already solved with the current schema.
Quoted 8 lines
Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml memory@0 { · line 43
Quoted 6 lines
Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml new file +1
-1@@ -39,7 +40,7 @@ memory@0 { reg = <0x0 0x0 0x0 0x0>; }; - sd_1v8: regulator-1v8 { + fixed_1v8: regulator-1v8 {Rename relevant?
I guess I can do the rename to a different patch - or maybe even better - drop this regulator on this series and re-add with a different name on some other patch.
The thing is that this regulator is currently used by the SDIO device drivers. That's the reason why it starts with "sd_".
However, at the real hardware, there are 3 different regulator outputs for SDIO related stuff. Such change is inside this patchset.
However, there is the need of a 1v8 fixed power line used on another upcoming driver. I guess I was too lazy to keep the DT info here ;-)
Quoted 4 lines
Quoted 4 lines
drivers/mfd/Kconfig +0
-0
Quoted 8 lines
drivers/mfd/Kconfig config MFD_HI6421_PMIC · line 496
Quoted 6 lines
drivers/mfd/Kconfig +1
-1@@ -493,10 +493,25 @@ config MFD_HI6421_PMIC Add support for HiSilicon Hi6421 PMIC. Hi6421 includes multi- functions, such as regulators, RTC, codec, Coulomb counter, etc. This driver includes core APIs _only_. You have to select - individul components like voltage regulators under corresponding + individual components like voltage regulators under correspondingDon't fix other drivers.
This is actually on an independent patch:
https://lore.kernel.org/lkml/176043f329dfa9889f014feec04e7e1553077873.1597160086.git.mchehab+huawei@kernel.org/T/#m1864011fa82154c6aa27fd4b2e9fce396bb3cd33
I guess I'll just submit this specific one outside this series.
Quoted 11 lines
drivers/mfd/Kconfig config MFD_HI6421_PMIC · line 504
Quoted 9 lines
drivers/mfd/Kconfig +5
-0menus in order to enable them. We communicate with the Hi6421 via memory-mapped I/O. +config MFD_HI6421_SPMI + tristate "HiSilicon Hi6421v600 SPMI PMU/Codec IC" + depends on OF + select MFD_CORE + select REGMAP_MMIONice thought, but it doesn't use it yet!
What do you mean? Makefile should be using it:
$ git grep MFD_HI6421_SPMI drivers/mfd/Kconfig:config MFD_HI6421_SPMI drivers/mfd/Makefile:obj-$(CONFIG_MFD_HI6421_SPMI) += hi6421-spmi-pmic.o
Quoted 16 lines
Quoted 16 lines
drivers/mfd/Kconfig +16
-0+ * + */ + +#include <linux/slab.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <linux/module.h> +#include <linux/err.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/mfd/core.h> +#include <linux/platform_device.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/of_device.h> +#include <linux/of_gpio.h>
Quoted 8 lines
drivers/mfd/Kconfig
Quoted 6 lines
drivers/mfd/Kconfig +6
-0+#include <linux/of_irq.h> +#include <linux/mfd/hi6421-spmi-pmic.h> +#include <linux/irq.h> +#include <linux/spmi.h> +#ifndef NO_IRQ +#define NO_IRQ 0Drop
Ok! I was in doubt about that, as there are a few other drivers with the same pattern:
drivers/ata/sata_dwc_460ex.c:#define NO_IRQ 0
drivers/input/touchscreen/ucb1400_ts.c:#define NO_IRQ 0
drivers/mmc/host/of_mmc_spi.c:#define NO_IRQ 0 drivers/pcmcia/pd6729.c:#define NO_IRQ ((unsigned int)(0)) drivers/rtc/rtc-m48t59.c:#define NO_IRQ (-1)
Btw, this definition at the rtc driver sounds weird ;-)
Quoted 9 lines
drivers/mfd/Kconfig
Quoted 5 lines
drivers/mfd/Kconfig +5
-0+ +/* + * The PMIC register is only 8-bit. + * Hisilicon SoC use hardware to map PMIC register into SoC mapping. + * At here, we are accessing SoC register with 32-bit.Can we return the 8 bits in an int and hence also return error codes?
Quoted 2 lines
+ */
+u32hi6421_spmi_pmic_read(struct hi6421_spmi_pmic *pmic, int reg)
I'll change the driver to use "int" and return proper error codes on errors.
Quoted 11 lines
drivers/mfd/Kconfig
Quoted 5 lines
drivers/mfd/Kconfig +5
-0+ +static int get_pmic_device_tree_data(struct device_node *np, + struct hi6421_spmi_pmic *pmic) +{ + int ret = 0;always set.
drivers/mfd/Kconfig
Quoted 2 lines
drivers/mfd/Kconfig +2
-0+ + /*get pmic irq num*/Comments are mostly fiarly obvious.
Yep. I'll drop the obvious ones.
Quoted 3 lines
Also if there is one, why use an array read?
drivers/mfd/Kconfig
Quoted 2 lines
drivers/mfd/Kconfig +2
-0+ ret = of_property_read_u32_array(np, "irq-num", + &pmic->irqnum, 1);
Good point. I'll fix it.
Quoted 4 lines
drivers/mfd/Kconfig
Quoted 1 line
drivers/mfd/Kconfig +1
-0+ /*SOC_PMIC_IRQ0_ADDR*/These superficially feel like things that would come from the compatible, but maybe I'm missing something.
My guess is that this is decided by the board manufacturer. I mean, from the schematics:
This is a separate chipset, connected at the Kirin 970 SPMI bus. The SPMI bus allows up to 16 PMICs. So, I would assume that a chip designed to support SPMI would have the flexibility of using different IRQ lines, being programmable either via some firmware or via some wiring.
Without knowing more, IMO the best would be to keep those settings at DT.
Quoted 5 lines
drivers/mfd/Kconfig
Quoted 3 lines
drivers/mfd/Kconfig +2
-0+ ret = of_property_read_u32_array(np, "irq-addr", + (int *)&pmic->irq_addr, 2);Unsurprisingly this takes a u32 * not a int *
I'll remove the casting. Btw, I guess I'll even replace it by a single number instead of an array, as the second value is already at the "irq-array" DT property:
irq-num = <16>; irq-array = <2>; irq-mask-addr = <0x202 2>; irq-addr = <0x212 2>;
The arrays for irq-mask-addr and irq-addr are:
struct hi6421_spmi_irq_mask_info {
int start_addr;
int array;
};
struct hi6421_spmi_irq_info {
int start_addr;
int array;
};At the code, sometimes it uses irq_mask->array, while on others it use irqarray, apparently for the same goal. So, it sounds safe to get rid of the duplication there. I'll place this on a separate patch, as I might have been missing something.
Quoted 37 lines
Quoted 37 lines
drivers/mfd/Kconfig +36
-0+ if (ret) {f_prop + pr_err("no irq-addr property set\n"); + ret = -ENODEV; + return ret; + } + + return ret; +} + +static void hi6421_spmi_pmic_irq_prc(struct hi6421_spmi_pmic *pmic) +{ + int i; + + for (i = 0 ; i < pmic->irq_mask_addr.array; i++) + hi6421_spmi_pmic_write(pmic, pmic->irq_mask_addr.start_addr + i, + HISI_MASK_STATE); + + for (i = 0 ; i < pmic->irq_addr.array; i++) { + unsigned int pending = hi6421_spmi_pmic_read(pmic, pmic->irq_addr.start_addr + i); + + pr_debug("PMU IRQ address value:irq[0x%x] = 0x%x\n", + pmic->irq_addr.start_addr + i, pending); + hi6421_spmi_pmic_write(pmic, pmic->irq_addr.start_addr + i, + HISI_MASK_STATE); + } +} + +static int hi6421_spmi_pmic_probe(struct spmi_device *pdev) +{ + struct device *dev = &pdev->dev; + struct device_node *np = dev->of_node; + struct hi6421_spmi_pmic *pmic = NULL; + enum of_gpio_flags flags; + int ret = 0; + int i; + unsigned int virq;
Quoted 8 lines
drivers/mfd/Kconfig
Quoted 6 lines
drivers/mfd/Kconfig +6
-0+ + pmic = devm_kzalloc(dev, sizeof(*pmic), GFP_KERNEL); + if (!pmic) + return -ENOMEM; + + /*TODO: get pmic dts info*/Seems to be done?
Sounds some obsolete comment. I'll drop it.
Quoted 16 lines
drivers/mfd/Kconfig
Quoted 13 lines
drivers/mfd/Kconfig +12
-0+ ret = get_pmic_device_tree_data(np, pmic); + if (ret) { + dev_err(&pdev->dev, "Error reading hisi pmic dts\n"); + return ret; + } + + /* TODO: get and enable clk request */ + spin_lock_init(&pmic->lock); + + pmic->dev = dev; + + pmic->gpio = of_get_gpio_flags(np, 0, &flags);Do we need flags for something?
Quoted 4 lines
Can we use the
gpio/consumer.hinterfaces for all this?Though I'm not sure we need a gpio at all. Looks like we just use it as an interrupt. Get an interrupt directly instead.
Yeah, from what I saw, the GPIOs supported right now by this driver are just for IRQs.
Quoted 32 lines
Quoted 32 lines
drivers/mfd/Kconfig +32
-0+ if (pmic->gpio < 0) + return pmic->gpio; + + if (!gpio_is_valid(pmic->gpio)) + return -EINVAL; + + ret = gpio_request_one(pmic->gpio, GPIOF_IN, "pmic"); + if (ret < 0) { + dev_err(dev, "failed to request gpio%d\n", pmic->gpio); + return ret; + } + + pmic->irq = gpio_to_irq(pmic->gpio); + + /* mask && clear IRQ status */ + hi6421_spmi_pmic_irq_prc(pmic); + + pmic->irqs = devm_kzalloc(dev, pmic->irqnum * sizeof(int), GFP_KERNEL); + if (!pmic->irqs) + goto irq_malloc; + + pmic->domain = irq_domain_add_simple(np, pmic->irqnum, 0, + &hi6421_spmi_domain_ops, pmic); + if (!pmic->domain) { + dev_err(dev, "failed irq domain add simple!\n"); + ret = -ENODEV; + goto irq_domain; + } + + for (i = 0; i < pmic->irqnum; i++) { + virq = irq_create_mapping(pmic->domain, i); + if (virq == NO_IRQ) {
Quoted 8 lines
drivers/mfd/Kconfig
Quoted 6 lines
drivers/mfd/Kconfig +6
-0+ pr_debug("Failed mapping hwirq\n"); + ret = -ENOSPC; + goto irq_create_mapping; + } + pmic->irqs[i] = virq; + pr_info("[%s]. pmic->irqs[%d] = %d\n", __func__, i, pmic->irqs[i]);Noise
Yep. Will drop or convert into dev_dbg().
Quoted 18 lines
Quoted 18 lines
drivers/mfd/Kconfig +17
-0+ } + + ret = request_threaded_irq(pmic->irq, hi6421_spmi_irq_handler, NULL, + IRQF_TRIGGER_LOW | IRQF_SHARED | IRQF_NO_SUSPEND, + "pmic", pmic); + if (ret < 0) { + dev_err(dev, "could not claim pmic %d\n", ret); + ret = -ENODEV; + goto request_theaded_irq; + } + + dev_set_drvdata(&pdev->dev, pmic); + + /* + * The logic below will rely that the pmic is already stored at + * drvdata. + */
Quoted 8 lines
drivers/mfd/Kconfig
Quoted 5 lines
drivers/mfd/Kconfig +5
-0+ dev_dbg(&pdev->dev, "SPMI-PMIC: adding children for %pOF\n", + pdev->dev.of_node); + ret = devm_mfd_add_devices(&pdev->dev, PLATFORM_DEVID_NONE, + hi6421v600_devs, ARRAY_SIZE(hi6421v600_devs), + NULL, 0, NULL);This is mixing and matching managed an unmanaged. Should be one or the other or we might be hiding some race conditions.
Actually, it is just the opposite. It took me a lot of time to figure out a good solution that will prevent all race conditions at probe time.
See, the SPMI variant of HiSilicon 6421 requires the drivers to be probed on a very specific order:
- The SPMI controller should be loaded first, as it provides the low-level I/O access to the serial bus used to talk with the PMICs. This bus is somewhat similar to the I2C bus.
Once the controller is registered, the SPMI bus probes the PMIC driver.
- Then, the MFD PMIC driver should be loaded. This adds support for a high level set of I/O operations, which are used by the regulator driver. Again, this approach is similar to the one taken by the I2C Kernel drivers.
- Finally, the regulator drivers should come, as they rely on the MFD I/O operations in order to talk with the SPMI bus.
The OOT driver probing was based on a some dirty hacks: it had an empty SPMI entry at the SoC, carrying on just the "compatible" line.
Then, another entry at DT with the real SPMI settings.
With such dirty hack, on Kernel 4.9, the PMIC driver were always loading before the regulator ones, as the SPMI bus code were serializing the probe there.
However, such settings were too fragile and broke after porting to upstream Kernels, because the regulator drivers were probed on a random order, typically before the MFD one (and sometimes even before the SPMI controller driver). Adding EPROBE_DEFER didn't solve all the issues, and made a complex and hard to debug scenario. Also, regulators were probed on a random order, making harder to debug issues there.
So, I ended using the same solution used by the already-existing drivers/mfd/hi6421-pmic-core.c driver[1].
[1] This variant of the 6421 chipset is a lot simpler, as it doesn't use the SPMI bus.
With such approach, the probing is warranted to happen the way it is expected by the driver:
SPMI controller code starts:
[ 0.416862] spmi_controller fff24000.spmi: HISI SPMI probe [ 0.422419] spmi spmi-0: allocated controller 0x(____ptrval____) id 0 [ 0.428929] spmi_controller fff24000.spmi: spmi_add_controller base addr=0xffff800012055000! [ 0.437480] spmi spmi-0: adding child /spmi@fff24000/pmic@0 [ 0.443109] spmi spmi-0: read usid 00 [ 0.446821] spmi 2-00: device 2-00 registered [ 0.451220] spmi spmi-0: spmi-2 registered: dev:(____ptrval____) [ 0.457286] spmi_controller fff24000.spmi: spmi_add_controller initialized
The PMIC probe happens sometime after spmi_controller registers itself at the SPMI bus:
[ 1.955838] [hi6421_spmi_pmic_probe]. pmic->irqs[0] = 43 ... [ 2.036298] [hi6421_spmi_pmic_probe]. pmic->irqs[15] = 58
After being ready to handle I/O requests, it starts probing the regulators:
[ 2.057815] hi6421v600-regulator hi6421v600-regulator: adding child /spmi@fff24000/pmic@0/regulators/ldo3@16 [ 2.199827] hi6421v600-regulator hi6421v600-regulator: adding child /spmi@fff24000/pmic@0/regulators/ldo4@17 [ 2.336284] hi6421v600-regulator hi6421v600-regulator: adding child /spmi@fff24000/pmic@0/regulators/ldo9@1C [ 2.472675] hi6421v600-regulator hi6421v600-regulator: adding child /spmi@fff24000/pmic@0/regulators/ldo15@21 [ 2.609402] hi6421v600-regulator hi6421v600-regulator: adding child /spmi@fff24000/pmic@0/regulators/ldo16@22 [ 2.746378] hi6421v600-regulator hi6421v600-regulator: adding child /spmi@fff24000/pmic@0/regulators/ldo17@23 [ 2.846707] hi6421v600-regulator hi6421v600-regulator: adding child /spmi@fff24000/pmic@0/regulators/ldo33@32 [ 2.988646] hi6421v600-regulator hi6421v600-regulator: adding child /spmi@fff24000/pmic@0/regulators/ldo34@33
As the current code serializes the regulator probing, it ensured that they'll happen at the right order, avoiding race conditions at probe time.
Quoted 18 lines
Quoted 18 lines
drivers/mfd/Kconfig +16
-0+ if (ret) { + dev_err(&pdev->dev, "Failed to add child devices: %d\n", ret); + return ret; + } + + return 0; + +request_theaded_irq: +irq_create_mapping: +irq_domain: +irq_malloc: + gpio_free(pmic->gpio); + return ret; +} + +static void hi6421_spmi_pmic_remove(struct spmi_device *pdev)
Quoted 8 lines
drivers/mfd/Kconfig
Quoted 6 lines
drivers/mfd/Kconfig +6
-0+{ + struct hi6421_spmi_pmic *pmic = dev_get_drvdata(&pdev->dev); + + free_irq(pmic->irq, pmic); + gpio_free(pmic->gpio); + devm_kfree(&pdev->dev, pmic);I hope that isn't needed!
Yeah, we can get rid of devm_kfree().
Quoted 29 lines
Quoted 29 lines
drivers/mfd/Kconfig +20
-0+} + +static const struct of_device_id pmic_spmi_id_table[] = { + { .compatible = "hisilicon,hi6421-spmi-pmic" }, + { } +}; +MODULE_DEVICE_TABLE(of, pmic_spmi_id_table); + +static struct spmi_driver hi6421_spmi_pmic_driver = { + .driver = { + .name = "hi6421-spmi-pmic", + .of_match_table = pmic_spmi_id_table, + }, + .probe = hi6421_spmi_pmic_probe, + .remove = hi6421_spmi_pmic_remove, +}; +module_spmi_driver(hi6421_spmi_pmic_driver); + +MODULE_DESCRIPTION("HiSilicon Hi6421v600 SPMI PMIC driver"); +MODULE_LICENSE("GPL v2");drivers/regulator/Kconfig +0
-0@@ -356,6 +356,14 @@ config REGULATOR_HI6421V530 provides 5 general purpose LDOs, and all of them come with support to either ECO (idle) or sleep mode.
Quoted 5 lines
drivers/regulator/Kconfig config REGULATOR_HI6421V530 · line 361
Quoted 3 lines
drivers/regulator/Kconfig +3
-0+config REGULATOR_HI6421V600 + tristate "HiSilicon Hi6421v600 PMIC voltage regulator support" + depends on MFD_HI6421_PMIC && OFCan we do a
COMPILE_TESThere?
Neither REGULATOR_HI6421V600 nor MFD_HI6421_PMIC depends on ARM or ARM64, so they should build fine on any arch. So, I'm failing to see why adding COMPILE_TEST would make any difference.
Quoted 18 lines
Quoted 18 lines
drivers/regulator/Kconfig +18
-0+ +#include <linux/slab.h> +#include <linux/device.h> +#include <linux/module.h> +#include <linux/err.h> +#include <linux/io.h> +#include <linux/platform_device.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/of_address.h> +#include <linux/regmap.h> +#include <linux/regulator/driver.h> +#include <linux/regulator/machine.h> +#include <linux/regulator/of_regulator.h> +#include <linux/mfd/hi6421-spmi-pmic.h> +#include <linux/delay.h> +#include <linux/time.h> +#include <linux/version.h>
Quoted 8 lines
drivers/regulator/Kconfig
Quoted 6 lines
drivers/regulator/Kconfig +6
-0+#include <linux/seq_file.h> +#include <linux/uaccess.h> +#include <linux/spmi.h> + +#define rdev_dbg(rdev, fmt, arg...) \ + pr_debug("%s: %s: " fmt, (rdev)->desc->name, __func__, ##arg)Not worth defining in my view.
That was my first approach: to drop any existing printk macro, replacing them by dev_dbg(). However, with dev_dbg(), the logs were like:
[ 2.069301] platform ldo3: LDO doesn't support economy mode. [ 2.074969] platform ldo3: voltage selector settings: reg: 0x51, mask: 0xf [ 2.094593] regulator.3: hi6421_spmi_regulator_get_voltage_sel: vsel_reg=0x51, value=0x8, entry=0x8, voltage=1800 mV [ 2.105530] regulator.3: hi6421_spmi_regulator_enable: off_on_delay=20000 us, enable_reg=0x16, enable_mask=0x1 [ 2.153484] regulator.3: hi6421_spmi_regulator_get_voltage_sel: vsel_reg=0x51, value=0x8, entry=0x8, voltage=1800 mV [ 2.163409] ldo3: 1500 <--> 2000 mV at 1800 mV normal [ 2.181305] regulator.3: hi6421_spmi_regulator_get_voltage_sel: vsel_reg=0x51, value=0x8, entry=0x8, voltage=1800 mV [ 2.191289] regulator.3: hi6421_spmi_regulator_probe_ldo: valid_modes_mask: 0x2, valid_ops_mask: 0x9
E. g. the messages printed by the regulator's core were using (rdev)->desc->name on their printks, producing a nice debug (when enabled at core level), while dev_dbg() were using a different name.
In this specific case, one might assume that "regulator.3" is "ldo3", but this is by coincidence, as it actually matches the sysfs entries:
$ ls -l /sys/class/regulator/ lrwxrwxrwx 1 root root 0 ago 12 08:26 regulator.0 -> ../../devices/platform/reg-dummy/regulator/regulator.0 lrwxrwxrwx 1 root root 0 ago 12 08:26 regulator.1 -> ../../devices/platform/regulator-1v8/regulator/regulator.1 lrwxrwxrwx 1 root root 0 ago 12 08:26 regulator.10 -> ../../devices/platform/spmi-0/2-00/ldo34/regulator/regulator.10 lrwxrwxrwx 1 root root 0 ago 12 08:26 regulator.2 -> ../../devices/platform/wlan-en-1-8v/regulator/regulator.2 lrwxrwxrwx 1 root root 0 ago 12 08:26 regulator.3 -> ../../devices/platform/spmi-0/2-00/ldo3/regulator/regulator.3 lrwxrwxrwx 1 root root 0 ago 12 08:26 regulator.4 -> ../../devices/platform/spmi-0/2-00/ldo4/regulator/regulator.4 lrwxrwxrwx 1 root root 0 ago 12 08:26 regulator.5 -> ../../devices/platform/spmi-0/2-00/ldo9/regulator/regulator.5 lrwxrwxrwx 1 root root 0 ago 12 08:26 regulator.6 -> ../../devices/platform/spmi-0/2-00/ldo15/regulator/regulator.6 lrwxrwxrwx 1 root root 0 ago 12 08:26 regulator.7 -> ../../devices/platform/spmi-0/2-00/ldo16/regulator/regulator.7 lrwxrwxrwx 1 root root 0 ago 12 08:26 regulator.8 -> ../../devices/platform/spmi-0/2-00/ldo17/regulator/regulator.8 lrwxrwxrwx 1 root root 0 ago 12 08:26 regulator.9 -> ../../devices/platform/spmi-0/2-00/ldo33/regulator/regulator.9
When playing with DT, the "regulator.[\d+]" namespace may change, making harder to debug stuff. So, basically, enabling just the logs at the regulator driver were requiring to double-check the sysfs entries in order to see what "regulator.3" were actually meaning with a particular DT setting.
After adding the macro, the output is a lot easier to be understood:
[ 2.069301] platform ldo3: LDO doesn't support economy mode. [ 2.074969] platform ldo3: voltage selector settings: reg: 0x51, mask: 0xf [ 2.094593] ldo3: hi6421_spmi_regulator_get_voltage_sel: vsel_reg=0x51, value=0x8, entry=0x8, voltage=1800 mV [ 2.105530] ldo3: hi6421_spmi_regulator_enable: off_on_delay=20000 us, enable_reg=0x16, enable_mask=0x1 [ 2.153484] ldo3: hi6421_spmi_regulator_get_voltage_sel: vsel_reg=0x51, value=0x8, entry=0x8, voltage=1800 mV [ 2.163409] ldo3: 1500 <--> 2000 mV at 1800 mV normal [ 2.181305] ldo3: hi6421_spmi_regulator_get_voltage_sel: vsel_reg=0x51, value=0x8, entry=0x8, voltage=1800 mV [ 2.191289] ldo3: hi6421_spmi_regulator_probe_ldo: valid_modes_mask: 0x2, valid_ops_mask: 0x9
As the name which got printed is the one that actually makes sense for someone working with the driver, as it matches the DT entries and the hardware power supply lines.
Quoted 11 lines
drivers/regulator/Kconfig
Quoted 8 lines
drivers/regulator/Kconfig +8
-0+static int hi6421_spmi_regulator_set_voltage_sel(struct regulator_dev *rdev, + unsigned int selector) +{ + struct hi6421v600_regulator *sreg = rdev_get_drvdata(rdev); + struct hi6421_spmi_pmic *pmic = sreg->pmic; + u32 reg_val; + + /* unlikely to happen. sanity test done by regulator core */Unlikely or can't?
Quoted 2 lines
drivers/regulator/Kconfig
Quoted 2 lines
drivers/regulator/Kconfig +2
-0+ if (unlikely(selector >= rdev->desc->n_voltages)) + return -EINVAL;
Good question. I almost removed this check, but I didn't check the regulator code with enough care to be 100% sure. So, I opted to keep it here.
Quoted 68 lines
Quoted 68 lines
drivers/regulator/Kconfig +68
-0+ + reg_val = selector << (ffs(rdev->desc->vsel_mask) - 1); + + /* set voltage selector */ + rdev_dbg(rdev, + "vsel_reg=0x%x, mask=0x%x, value=0x%x, voltage=%d mV\n", + rdev->desc->vsel_reg, rdev->desc->vsel_mask, reg_val, + rdev->desc->ops->list_voltage(rdev, selector) / 1000); + + hi6421_spmi_pmic_rmw(pmic, rdev->desc->vsel_reg, + rdev->desc->vsel_mask, reg_val); + + return 0; +} + +static unsigned int hi6421_spmi_regulator_get_mode(struct regulator_dev *rdev) +{ + struct hi6421v600_regulator *sreg = rdev_get_drvdata(rdev); + struct hi6421_spmi_pmic *pmic = sreg->pmic; + u32 reg_val; + unsigned int mode; + + reg_val = hi6421_spmi_pmic_read(pmic, rdev->desc->enable_reg); + + if (reg_val & sreg->eco_mode_mask) + mode = REGULATOR_MODE_IDLE; + else + mode = REGULATOR_MODE_NORMAL; + + rdev_dbg(rdev, + "enable_reg=0x%x, eco_mode_mask=0x%x, reg_val=0x%x, %s mode\n", + rdev->desc->enable_reg, sreg->eco_mode_mask, reg_val, + mode == REGULATOR_MODE_IDLE ? "idle" : "normal"); + + return mode; +} + +static int hi6421_spmi_regulator_set_mode(struct regulator_dev *rdev, + unsigned int mode) +{ + struct hi6421v600_regulator *sreg = rdev_get_drvdata(rdev); + struct hi6421_spmi_pmic *pmic = sreg->pmic; + u32 val; + + switch (mode) { + case REGULATOR_MODE_NORMAL: + val = 0; + break; + case REGULATOR_MODE_IDLE: + val = sreg->eco_mode_mask << (ffs(sreg->eco_mode_mask) - 1); + break; + default: + return -EINVAL; + } + + /* set mode */ + rdev_dbg(rdev, "enable_reg=0x%x, eco_mode_mask=0x%x, value=0x%x\n", + rdev->desc->enable_reg, sreg->eco_mode_mask, val); + + hi6421_spmi_pmic_rmw(pmic, rdev->desc->enable_reg, + sreg->eco_mode_mask, val); + + return 0; +} + +static unsigned int +hi6421_spmi_regulator_get_optimum_mode(struct regulator_dev *rdev, + int input_uV, int output_uV,
Quoted 8 lines
drivers/regulator/Kconfig
Quoted 6 lines
drivers/regulator/Kconfig +6
-0+ int load_uA) +{ + struct hi6421v600_regulator *sreg = rdev_get_drvdata(rdev); + + if (load_uA || ((unsigned int)load_uA > sreg->eco_uA)) { + rdev_dbg(rdev, "normal mode");Debug seems unnecessary to me, but maybe keep it if you want.
I actually used this debug. There are some LDO lines which don't support eco mode. The original driver was hard to understand that. So, I ended by re-writing the part of the code which sets/uses it[1]:
+ /* hisi regulator supports two modes */
+ constraint = &initdata->constraints;
+
+ constraint->valid_modes_mask = REGULATOR_MODE_NORMAL;
+ if (sreg->eco_mode_mask) {
+ constraint->valid_modes_mask |= REGULATOR_MODE_IDLE;
+ constraint->valid_ops_mask |= REGULATOR_CHANGE_MODE;
+ }
+
Those debug messages are useful to double-check if something bad is not happening with the modes/ops masks.
Quoted 17 lines
drivers/regulator/Kconfig
Quoted 13 lines
drivers/regulator/Kconfig +13
-0+ /* register regulator */ + rdev = regulator_register(rdesc, &config); + if (IS_ERR(rdev)) { + dev_err(dev, "failed to register %s\n", + rdesc->name); + ret = PTR_ERR(rdev); + goto probe_end; + } + + rdev_dbg(rdev, "valid_modes_mask: 0x%x, valid_ops_mask: 0x%x\n", + constraint->valid_modes_mask, constraint->valid_ops_mask); + + dev_set_drvdata(dev, rdev);I'd do separate error path.
return 0;
Quoted 7 lines
drivers/regulator/Kconfig
Quoted 2 lines
drivers/regulator/Kconfig +2
-0+probe_end: + if (ret)ret is set if separate error path.
I haven't figured out lifetime but can we not use devm for sreg?drivers/regulator/Kconfig
Quoted 1 line
drivers/regulator/Kconfig +1
-0+ kfree(sreg);
I guess we can. I'll check and change if ok.
Quoted 10 lines
drivers/regulator/Kconfig
Quoted 8 lines
drivers/regulator/Kconfig +8
-0+static int hi6421_spmi_regulator_remove(struct platform_device *pdev) +{ + struct regulator_dev *rdev = dev_get_drvdata(&pdev->dev); + struct hi6421v600_regulator *sreg = rdev_get_drvdata(rdev); + + regulator_unregister(rdev); + + /* TODO: should i worry about that? devm_kzalloc */Answer that TODO. No unless something odd going on.
Yeah, agreed. I'll cleanup useless comments on this driver.
Quoted 8 lines
drivers/regulator/Kconfig
Quoted 5 lines
drivers/regulator/Kconfig +4
-0+ if (rdev->desc->volt_table) + devm_kfree(&pdev->dev, (unsigned int *)rdev->desc->volt_table); + + kfree(sreg);This is a worrying mix of devm and not. Never a good sign. Lifetime of sreg seems strange.
I guess we can just get rid of both, converting sreg to use devm alloc.
Btw, at least on Hikey 970 (which happens to be the only board using it so far), in practice this driver should never be removed, as, among other things, it controls the power supply for storage (both SD and MMC).
Quoted 8 lines
Quoted 8 lines
drivers/spmi/Kconfig +0
-0@@ -25,4 +25,13 @@ config SPMI_MSM_PMIC_ARB This is required for communicating with Qualcomm PMICs and other devices that have the SPMI interface.
Quoted 8 lines
drivers/spmi/Kconfig config SPMI_MSM_PMIC_ARB · line 31
Quoted 4 lines
drivers/spmi/Kconfig +4
-0+config SPMI_HISI3670 + tristate "Hisilicon 3670 SPMI Controller" + select IRQ_DOMAIN_HIERARCHY + depends on HAS_IOMEMI have a vague recollection some magic was done to mean we don't need that any more (stubs for the few cases where it doesn't exist). Could have remembered wrong though.
Yeah, I also have a vage remind about HAS_IOMEM and stubs at the headers (or some other config option similar to it), but not really sure.
There is just another SPMI driver. So, I ended playing safe here by duplicating select/depends on from the previous entry. Btw, there are several other places with the same pattern.
Quoted 7 lines
Quoted 7 lines
drivers/spmi/Kconfig +7
-0+ /* Start the transaction */ + writel(cmd, spmi_controller->base + chnl_ofst + SPMI_APB_SPMI_CMD_BASE_ADDR); + + rc = spmi_controller_wait_for_done(&ctrl->dev, spmi_controller, + spmi_controller->base, sid, addr); + spin_unlock_irqrestore(&spmi_controller->lock, flags); +
Quoted 8 lines
drivers/spmi/Kconfig
Quoted 6 lines
drivers/spmi/Kconfig +6
-0+ if (rc) + dev_err(&ctrl->dev, "spmi write wait timeout op:0x%x sid:%d addr:0x%x bc:%ld\n", + opc, sid, addr, bc); + else + dev_dbg(&ctrl->dev, "%s: id:%d addr:0x%x, wrote value: %*ph\n", + __func__, sid, addr, (int)bc, __buf);I'd drop the debug. Adds a lot of code for limited benefit.
Yeah, I guess this can now be dropped. That was required while fixing some endianness issues at the past code.
Quoted 7 lines
drivers/spmi/Kconfig
Quoted 5 lines
drivers/spmi/Kconfig +5
-0+ ret = spmi_controller_add(ctrl); + if (ret) + goto err_add_controller; + + dev_info(&pdev->dev, "spmi_add_controller initialized\n");Too noisy.
That's helpful to check if drivers initialized at the right order.
I'll change it to dev_dbg().
Quoted 7 lines
drivers/spmi/Kconfig
Quoted 5 lines
drivers/spmi/Kconfig +4
-0+ return 0; + +err_add_controller: + dev_err(&pdev->dev, "spmi_add_controller failed!\n");Seems too noisy to me given information provided is minimal.
I'll add the error code to the message.
Quoted 7 lines
drivers/spmi/spmi.c
Quoted 4 lines
drivers/spmi/spmi.c +0
-0All the changes in here look to be cleanup. Drop it from this series as it just adds noise.
Yeah, makes sense. Will submit it on a separate patch.
Quoted 9 lines
Quoted 9 lines
drivers/spmi/spmi.c +0
-2@@ -545,13 +548,10 @@ static int spmi_ctrl_remove_device(struct device *dev, void *data)*/ void spmi_controller_remove (struct spmi_controller *ctrl) { -int dummy; -if (!ctrl)return ;
Quoted 6 lines
drivers/spmi/spmi.c static int spmi_ctrl_remove_device(struct device *dev, void *data) · line 557
Quoted 6 lines
drivers/spmi/spmi.c +1
-2- dummy =device_for_each_child (&ctrl->dev,NULL , - spmi_ctrl_remove_device); +device_for_each_child (&ctrl->dev,NULL , spmi_ctrl_remove_device);device_del (&ctrl->dev); }EXPORT_SYMBOL_GPL (spmi_controller_remove);
This one is on a separate patch already. Will submit in separate.
Thanks,
Mauro
On Wed, 12 Aug 2020 09:45:40 +0200
Mauro Carvalho Chehab <[email protected]> wrote:
....
Quoted 13 lines
Quoted 5 lines
Quoted 5 lines
drivers/mfd/Kconfig +0
-0menus in order to enable them. We communicate with the Hi6421 via memory-mapped I/O.Quoted 7 lines
drivers/mfd/Kconfig config MFD_HI6421_PMIC · line 504
Quoted 5 lines
drivers/mfd/Kconfig +5
-0+config MFD_HI6421_SPMI + tristate "HiSilicon Hi6421v600 SPMI PMU/Codec IC" + depends on OF + select MFD_CORE + select REGMAP_MMIONice thought, but it doesn't use it yet!
Quoted 5 lines
What do you mean?
Makefileshould be using it:$ git grep MFD_HI6421_SPMI drivers/mfd/Kconfig:config MFD_HI6421_SPMI drivers/mfd/Makefile:obj-$(CONFIG_MFD_HI6421_SPMI) += hi6421-spmi-pmic.o
Just the REGMAP bit. Driver doesn't seem to be using regmap.
Quoted 30 lines
Quoted 18 lines
Quoted 18 lines
+ *
+ */drivers/mfd/hi6421-spmi-pmic.c new file +14
-0+ +#include <linux/slab.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <linux/module.h> +#include <linux/err.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/mfd/core.h> +#include <linux/platform_device.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/of_device.h> +#include <linux/of_gpio.h> Quoted 8 lines
drivers/mfd/hi6421-spmi-pmic.c line 38
Quoted 6 lines
drivers/mfd/hi6421-spmi-pmic.c new file +6
-0+#include <linux/of_irq.h> +#include <linux/mfd/hi6421-spmi-pmic.h> +#include <linux/irq.h> +#include <linux/spmi.h> +#ifndef NO_IRQ +#define NO_IRQ 0Drop
Ok! I was in doubt about that, as there are a few other drivers with the same pattern:
Quoted 7 lines
drivers/ata/sata_dwc_460ex.c:#define
NO_IRQ0
drivers/input/touchscreen/ucb1400_ts.c:#defineNO_IRQ0
drivers/mmc/host/of_mmc_spi.c:#defineNO_IRQ0 drivers/pcmcia/pd6729.c:#defineNO_IRQ((unsigned int)(0)) drivers/rtc/rtc-m48t59.c:#defineNO_IRQ(-1)Btw, this definition at the rtc driver sounds weird ;-)
History I guess. IIRC, a long time back, 0 was a valid IRQ for some architectures.
Quoted 11 lines
Quoted 5 lines
drivers/mfd/hi6421-spmi-pmic.c line 241
Quoted 2 lines
drivers/mfd/hi6421-spmi-pmic.c new file +1
-0+/*SOC_PMIC_IRQ0_ADDR*/ These superficially feel like things that would come from the compatible, but maybe I'm missing something.
My guess is that this is decided by the board manufacturer. I mean, from the schematics:
Quoted 7 lines
This is a separate chipset, connected at the Kirin 970 SPMI bus. The SPMI bus allows up to 16 PMICs. So, I would assume that a chip designed to support SPMI would have the flexibility of using different IRQ lines, being programmable either via some firmware or via some wiring.
Without knowing more, IMO the best would be to keep those settings at DT.
Fair enough. Would be nice if they could be established from a bus ID of some type and the compatible but if we don't have the info to be able to do that I guess we will have to do it this way.
Quoted 16 lines
Quoted 16 lines
drivers/mfd/hi6421-spmi-pmic.c line 297
Quoted 13 lines
drivers/mfd/hi6421-spmi-pmic.c new file +12
-0+ ret =get_pmic_device_tree_data (np, pmic); +if (ret) { +dev_err (&pdev->dev,"Error reading hisi pmic dts\n" ); +return ret; + } + +/* TODO: get and enable clk request */ +spin_lock_init (&pmic->lock); + + pmic->dev = dev; + + pmic->gpio =of_get_gpio_flags (np,0 , &flags);Do we need flags for something?
Quoted 7 lines
Quoted 4 lines
Can we use the
gpio/consumer.hinterfaces for all this?Though I'm not sure we need a gpio at all. Looks like we just use it as an interrupt. Get an interrupt directly instead.
Yeah, from what I saw, the GPIOs supported right now by this driver are just for IRQs.
Guess they all need switching to just being interrupt lines then.
Quoted 28 lines
Quoted 28 lines
Quoted 28 lines
drivers/mfd/hi6421-spmi-pmic.c new file +27
-0+if (pmic->gpio <0 ) +return pmic->gpio; + +if (!gpio_is_valid (pmic->gpio)) +return -EINVAL ; + + ret =gpio_request_one (pmic->gpio,GPIOF_IN ,"pmic" ); +if (ret <0 ) { +dev_err (dev,"failed to request gpio%d\n" , pmic->gpio); +return ret; + } + + ret =request_threaded_irq (pmic->irq, hi6421_spmi_irq_handler,NULL , +IRQF_TRIGGER_LOW |IRQF_SHARED |IRQF_NO_SUSPEND , +"pmic" , pmic); +if (ret <0 ) { +dev_err (dev,"could not claim pmic %d\n" , ret); + ret = -ENODEV ; + goto request_theaded_irq; + } + +dev_set_drvdata (&pdev->dev, pmic); + +/* +* The logic below will rely that the pmic is already stored at +* drvdata. +*/
Quoted 8 lines
Quoted 8 lines
drivers/mfd/hi6421-spmi-pmic.c line 357
Quoted 5 lines
drivers/mfd/hi6421-spmi-pmic.c new file +5
-0+dev_dbg (&pdev->dev,"SPMI-PMIC: adding children for %pOF\n" , + pdev->dev.of_node); + ret =devm_mfd_add_devices (&pdev->dev,PLATFORM_DEVID_NONE , + hi6421v600_devs,ARRAY_SIZE (hi6421v600_devs), +NULL ,0 ,NULL );This is mixing and matching managed an unmanaged. Should be one or the other or we might be hiding some race conditions.
I intended this as a more localized comment, though the following answers another question I had.
request_threaded_irq is not using devm_ whilst the add devices is. As a result we might have a path in which the irq goes away before the device cleanup happens.
Quoted 32 lines
Actually, it is just the opposite. It took me a lot of time to figure out a good solution that will prevent all race conditions at probe time.
See, the SPMI variant of HiSilicon 6421 requires the drivers to be probed on a very specific order:
- The SPMI controller should be loaded first, as it provides the low-level I/O access to the serial bus used to talk with the PMICs. This bus is somewhat similar to the I2C bus.
Once the controller is registered, the SPMI bus probes the PMIC driver.
- Then, the MFD PMIC driver should be loaded. This adds support for a high level set of I/O operations, which are used by the regulator driver. Again, this approach is similar to the one taken by the I2C Kernel drivers.
- Finally, the regulator drivers should come, as they rely on the MFD I/O operations in order to talk with the SPMI bus.
The OOT driver probing was based on a some dirty hacks: it had an empty SPMI entry at the SoC, carrying on just the "compatible" line.
Then, another entry at DT with the real SPMI settings.
With such dirty hack, on Kernel 4.9, the PMIC driver were always loading before the regulator ones, as the SPMI bus code were serializing the probe there.
Quoted 7 lines
However, such settings were too fragile and broke after porting to upstream Kernels, because the regulator drivers were probed on a random order, typically before the MFD one (and sometimes even before the SPMI controller driver). Adding
EPROBE_DEFERdidn't solve all the issues, and made a complex and hard to debug scenario. Also, regulators were probed on a random order, making harder to debug issues there.
There are no ordering guarantees IIRC in mfd children coming up even in the normal path. It might currently happen in a particular order but relying on that seems fragile to me.
Quoted 39 lines
So, I ended using the same solution used by the already-existing
drivers/mfd/hi6421-pmic-core.cdriver[1].[1] This variant of the 6421 chipset is a lot simpler, as it doesn't use the SPMI bus.
With such approach, the probing is warranted to happen the way it is expected by the driver:
SPMI controller code starts:
[ 0.416862] spmi_controller fff24000.spmi: HISI SPMI probe [ 0.422419] spmi spmi-0: allocated controller 0x(____ptrval____) id 0 [ 0.428929] spmi_controller fff24000.spmi: spmi_add_controller base addr=0xffff800012055000! [ 0.437480] spmi spmi-0: adding child /spmi@fff24000/pmic@0 [ 0.443109] spmi spmi-0: read usid 00 [ 0.446821] spmi 2-00: device 2-00 registered [ 0.451220] spmi spmi-0: spmi-2 registered: dev:(____ptrval____) [ 0.457286] spmi_controller fff24000.spmi: spmi_add_controller initializedThe PMIC probe happens sometime after
spmi_controllerregisters itself at the SPMI bus:[ 1.955838] [hi6421_spmi_pmic_probe]. pmic->irqs[0] = 43 ... [ 2.036298] [hi6421_spmi_pmic_probe]. pmic->irqs[15] = 58After being ready to handle I/O requests, it starts probing the regulators:
[ 2.057815] hi6421v600-regulator hi6421v600-regulator: adding child /spmi@fff24000/pmic@0/regulators/ldo3@16 [ 2.199827] hi6421v600-regulator hi6421v600-regulator: adding child /spmi@fff24000/pmic@0/regulators/ldo4@17 [ 2.336284] hi6421v600-regulator hi6421v600-regulator: adding child /spmi@fff24000/pmic@0/regulators/ldo9@1C [ 2.472675] hi6421v600-regulator hi6421v600-regulator: adding child /spmi@fff24000/pmic@0/regulators/ldo15@21 [ 2.609402] hi6421v600-regulator hi6421v600-regulator: adding child /spmi@fff24000/pmic@0/regulators/ldo16@22 [ 2.746378] hi6421v600-regulator hi6421v600-regulator: adding child /spmi@fff24000/pmic@0/regulators/ldo17@23 [ 2.846707] hi6421v600-regulator hi6421v600-regulator: adding child /spmi@fff24000/pmic@0/regulators/ldo33@32 [ 2.988646] hi6421v600-regulator hi6421v600-regulator: adding child /spmi@fff24000/pmic@0/regulators/ldo34@33
Quoted 3 lines
As the current code serializes the regulator probing, it ensured that they'll happen at the right order, avoiding race conditions at probe time.
Why do we need the regulators to come up in a particular order?
That sounds suspicious as any relationships between different ones should be expressed either in DT or in the order they are enabled in the drivers using them.
Quoted 18 lines
Quoted 12 lines
Quoted 12 lines
drivers/regulator/Kconfig +0
-0@@ -356,6 +356,14 @@ config REGULATOR_HI6421V530 provides 5 general purpose LDOs, and all of them come with support to either ECO (idle) or sleep mode.Quoted 5 lines
drivers/regulator/Kconfig config REGULATOR_HI6421V530 · line 361
Quoted 3 lines
drivers/regulator/Kconfig +3
-0+config REGULATOR_HI6421V600 + tristate "HiSilicon Hi6421v600 PMIC voltage regulator support" + depends on MFD_HI6421_PMIC && OFCan we do a
COMPILE_TESThere?
Quoted 3 lines
Neither
REGULATOR_HI6421V600norMFD_HI6421_PMICdepends on ARM or ARM64, so they should build fine on any arch. So, I'm failing to see why addingCOMPILE_TESTwould make any difference.
cool. Good to get the extra build coverage.
Quoted 77 lines
Quoted 19 lines
Quoted 19 lines
drivers/regulator/Kconfig +18
-0+ +#include <linux/slab.h> +#include <linux/device.h> +#include <linux/module.h> +#include <linux/err.h> +#include <linux/io.h> +#include <linux/platform_device.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/of_address.h> +#include <linux/regmap.h> +#include <linux/regulator/driver.h> +#include <linux/regulator/machine.h> +#include <linux/regulator/of_regulator.h> +#include <linux/mfd/hi6421-spmi-pmic.h> +#include <linux/delay.h> +#include <linux/time.h> +#include <linux/version.h>Quoted 8 lines
drivers/regulator/Kconfig
Quoted 6 lines
drivers/regulator/Kconfig +6
-0+#include <linux/seq_file.h> +#include <linux/uaccess.h> +#include <linux/spmi.h> + +#define rdev_dbg(rdev, fmt, arg...) \ + pr_debug("%s: %s: " fmt, (rdev)->desc->name, __func__, ##arg)Not worth defining in my view.
That was my first approach: to drop any existing printk macro, replacing them by
dev_dbg(). However, withdev_dbg(), the logs were like:[ 2.069301] platform ldo3: LDO doesn't support economy mode. [ 2.074969] platform ldo3: voltage selector settings: reg: 0x51, mask: 0xf [ 2.094593] regulator.3: hi6421_spmi_regulator_get_voltage_sel: vsel_reg=0x51, value=0x8, entry=0x8, voltage=1800 mV [ 2.105530] regulator.3: hi6421_spmi_regulator_enable: off_on_delay=20000 us, enable_reg=0x16, enable_mask=0x1 [ 2.153484] regulator.3: hi6421_spmi_regulator_get_voltage_sel: vsel_reg=0x51, value=0x8, entry=0x8, voltage=1800 mV [ 2.163409] ldo3: 1500 <--> 2000 mV at 1800 mV normal [ 2.181305] regulator.3: hi6421_spmi_regulator_get_voltage_sel: vsel_reg=0x51, value=0x8, entry=0x8, voltage=1800 mV [ 2.191289] regulator.3: hi6421_spmi_regulator_probe_ldo: valid_modes_mask: 0x2, valid_ops_mask: 0x9E. g. the messages printed by the regulator's core were using (rdev)->desc->name on their printks, producing a nice debug (when enabled at core level), while
dev_dbg()were using a different name.In this specific case, one might assume that "regulator.3" is "ldo3", but this is by coincidence, as it actually matches the sysfs entries:
$ ls -l /sys/class/regulator/ lrwxrwxrwx 1 root root 0 ago 12 08:26 regulator.0 -> ../../devices/platform/reg-dummy/regulator/regulator.0 lrwxrwxrwx 1 root root 0 ago 12 08:26 regulator.1 -> ../../devices/platform/regulator-1v8/regulator/regulator.1 lrwxrwxrwx 1 root root 0 ago 12 08:26 regulator.10 -> ../../devices/platform/spmi-0/2-00/ldo34/regulator/regulator.10 lrwxrwxrwx 1 root root 0 ago 12 08:26 regulator.2 -> ../../devices/platform/wlan-en-1-8v/regulator/regulator.2 lrwxrwxrwx 1 root root 0 ago 12 08:26 regulator.3 -> ../../devices/platform/spmi-0/2-00/ldo3/regulator/regulator.3 lrwxrwxrwx 1 root root 0 ago 12 08:26 regulator.4 -> ../../devices/platform/spmi-0/2-00/ldo4/regulator/regulator.4 lrwxrwxrwx 1 root root 0 ago 12 08:26 regulator.5 -> ../../devices/platform/spmi-0/2-00/ldo9/regulator/regulator.5 lrwxrwxrwx 1 root root 0 ago 12 08:26 regulator.6 -> ../../devices/platform/spmi-0/2-00/ldo15/regulator/regulator.6 lrwxrwxrwx 1 root root 0 ago 12 08:26 regulator.7 -> ../../devices/platform/spmi-0/2-00/ldo16/regulator/regulator.7 lrwxrwxrwx 1 root root 0 ago 12 08:26 regulator.8 -> ../../devices/platform/spmi-0/2-00/ldo17/regulator/regulator.8 lrwxrwxrwx 1 root root 0 ago 12 08:26 regulator.9 -> ../../devices/platform/spmi-0/2-00/ldo33/regulator/regulator.9When playing with DT, the "regulator.[\d+]" namespace may change, making harder to debug stuff. So, basically, enabling just the logs at the regulator driver were requiring to double-check the sysfs entries in order to see what "regulator.3" were actually meaning with a particular DT setting.
After adding the macro, the output is a lot easier to be understood:
[ 2.069301] platform ldo3: LDO doesn't support economy mode. [ 2.074969] platform ldo3: voltage selector settings: reg: 0x51, mask: 0xf [ 2.094593] ldo3: hi6421_spmi_regulator_get_voltage_sel: vsel_reg=0x51, value=0x8, entry=0x8, voltage=1800 mV [ 2.105530] ldo3: hi6421_spmi_regulator_enable: off_on_delay=20000 us, enable_reg=0x16, enable_mask=0x1 [ 2.153484] ldo3: hi6421_spmi_regulator_get_voltage_sel: vsel_reg=0x51, value=0x8, entry=0x8, voltage=1800 mV [ 2.163409] ldo3: 1500 <--> 2000 mV at 1800 mV normal [ 2.181305] ldo3: hi6421_spmi_regulator_get_voltage_sel: vsel_reg=0x51, value=0x8, entry=0x8, voltage=1800 mV [ 2.191289] ldo3: hi6421_spmi_regulator_probe_ldo: valid_modes_mask: 0x2, valid_ops_mask: 0x9
Quoted 3 lines
As the name which got printed is the one that actually makes sense for someone working with the driver, as it matches the DT entries and the hardware power supply lines.
Fair enough. Guess this is one for Mark to ultimately decide.
Quoted 12 lines
Quoted 12 lines
drivers/regulator/Kconfig
Quoted 9 lines
drivers/regulator/Kconfig +8
-0+static int hi6421_spmi_regulator_set_voltage_sel(struct regulator_dev *rdev, + unsigned int selector) +{ + struct hi6421v600_regulator *sreg = rdev_get_drvdata(rdev); + struct hi6421_spmi_pmic *pmic = sreg->pmic; + u32 reg_val; + + /* unlikely to happen. sanity test done by regulator core */Unlikely or can't?
Quoted 6 lines
Quoted 2 lines
drivers/regulator/Kconfig
Quoted 2 lines
drivers/regulator/Kconfig +2
-0+ if (unlikely(selector >= rdev->desc->n_voltages)) + return -EINVAL;Good question. I almost removed this check, but I didn't check the regulator code with enough care to be 100% sure. So, I opted to keep it here.
I'd drop the comment then :) If someone else wants to figure it out in future then they are welcome to.
Quoted 92 lines
Quoted 69 lines
Quoted 69 lines
drivers/regulator/Kconfig +68
-0+ + reg_val = selector << (ffs(rdev->desc->vsel_mask) - 1); + + /* set voltage selector */ + rdev_dbg(rdev, + "vsel_reg=0x%x, mask=0x%x, value=0x%x, voltage=%d mV\n", + rdev->desc->vsel_reg, rdev->desc->vsel_mask, reg_val, + rdev->desc->ops->list_voltage(rdev, selector) / 1000); + + hi6421_spmi_pmic_rmw(pmic, rdev->desc->vsel_reg, + rdev->desc->vsel_mask, reg_val); + + return 0; +} + +static unsigned int hi6421_spmi_regulator_get_mode(struct regulator_dev *rdev) +{ + struct hi6421v600_regulator *sreg = rdev_get_drvdata(rdev); + struct hi6421_spmi_pmic *pmic = sreg->pmic; + u32 reg_val; + unsigned int mode; + + reg_val = hi6421_spmi_pmic_read(pmic, rdev->desc->enable_reg); + + if (reg_val & sreg->eco_mode_mask) + mode = REGULATOR_MODE_IDLE; + else + mode = REGULATOR_MODE_NORMAL; + + rdev_dbg(rdev, + "enable_reg=0x%x, eco_mode_mask=0x%x, reg_val=0x%x, %s mode\n", + rdev->desc->enable_reg, sreg->eco_mode_mask, reg_val, + mode == REGULATOR_MODE_IDLE ? "idle" : "normal"); + + return mode; +} + +static int hi6421_spmi_regulator_set_mode(struct regulator_dev *rdev, + unsigned int mode) +{ + struct hi6421v600_regulator *sreg = rdev_get_drvdata(rdev); + struct hi6421_spmi_pmic *pmic = sreg->pmic; + u32 val; + + switch (mode) { + case REGULATOR_MODE_NORMAL: + val = 0; + break; + case REGULATOR_MODE_IDLE: + val = sreg->eco_mode_mask << (ffs(sreg->eco_mode_mask) - 1); + break; + default: + return -EINVAL; + } + + /* set mode */ + rdev_dbg(rdev, "enable_reg=0x%x, eco_mode_mask=0x%x, value=0x%x\n", + rdev->desc->enable_reg, sreg->eco_mode_mask, val); + + hi6421_spmi_pmic_rmw(pmic, rdev->desc->enable_reg, + sreg->eco_mode_mask, val); + + return 0; +} + +static unsigned int +hi6421_spmi_regulator_get_optimum_mode(struct regulator_dev *rdev, + int input_uV, int output_uV,Quoted 8 lines
drivers/regulator/Kconfig
Quoted 6 lines
drivers/regulator/Kconfig +6
-0+ int load_uA) +{ + struct hi6421v600_regulator *sreg = rdev_get_drvdata(rdev); + + if (load_uA || ((unsigned int)load_uA > sreg->eco_uA)) { + rdev_dbg(rdev, "normal mode");Debug seems unnecessary to me, but maybe keep it if you want.
I actually used this debug. There are some LDO lines which don't support eco mode. The original driver was hard to understand that. So, I ended by re-writing the part of the code which sets/uses it[1]:
drivers/regulator/hi6421v600-regulator.c new file +9
-0+/* hisi regulator supports two modes */ + constraint = &initdata->constraints; + + constraint->valid_modes_mask =REGULATOR_MODE_NORMAL ; +if (sreg->eco_mode_mask) { + constraint->valid_modes_mask |=REGULATOR_MODE_IDLE ; + constraint->valid_ops_mask |=REGULATOR_CHANGE_MODE ; + } +
Quoted 4 lines
Those debug messages are useful to double-check if something bad is not happening with the modes/ops masks.
That's fine, but is it useful to have it upstream now you have debugged those issues? I'm not completely convinced it is and debug prints have a habit of rotting just like comments.
Quoted 51 lines
Quoted 19 lines
Quoted 5 lines
drivers/regulator/Kconfig +3
-0+ /* register regulator */ + rdev = regulator_register(rdesc, &config); + if (IS_ERR(rdev)) {drivers/regulator/Kconfig
Quoted 10 lines
drivers/regulator/Kconfig +10
-0+ dev_err(dev, "failed to register %s\n", + rdesc->name); + ret = PTR_ERR(rdev); + goto probe_end; + } + + rdev_dbg(rdev, "valid_modes_mask: 0x%x, valid_ops_mask: 0x%x\n", + constraint->valid_modes_mask, constraint->valid_ops_mask); + + dev_set_drvdata(dev, rdev);I'd do separate error path.
return 0;Quoted 7 lines
drivers/regulator/Kconfig
Quoted 2 lines
drivers/regulator/Kconfig +2
-0+probe_end: + if (ret)ret is set if separate error path.
I haven't figured out lifetime but can we not use devm for sreg?drivers/regulator/Kconfig
Quoted 1 line
drivers/regulator/Kconfig +1
-0+ kfree(sreg);I guess we can. I'll check and change if ok.
Quoted 10 lines
drivers/regulator/Kconfig
Quoted 8 lines
drivers/regulator/Kconfig +8
-0+static int hi6421_spmi_regulator_remove(struct platform_device *pdev) +{ + struct regulator_dev *rdev = dev_get_drvdata(&pdev->dev); + struct hi6421v600_regulator *sreg = rdev_get_drvdata(rdev); + + regulator_unregister(rdev); + + /* TODO: should i worry about that? devm_kzalloc */Answer that TODO. No unless something odd going on.
Yeah, agreed. I'll cleanup useless comments on this driver.
Quoted 8 lines
drivers/regulator/Kconfig
Quoted 5 lines
drivers/regulator/Kconfig +4
-0+ if (rdev->desc->volt_table) + devm_kfree(&pdev->dev, (unsigned int *)rdev->desc->volt_table); + + kfree(sreg);This is a worrying mix of devm and not. Never a good sign. Lifetime of sreg seems strange.
Quoted 6 lines
I guess we can just get rid of both, converting sreg to use devm alloc.
Btw, at least on Hikey 970 (which happens to be the only board using it so far), in practice this driver should never be removed, as, among other things, it controls the power supply for storage (both SD and MMC).
Who needs storage? :)
...
Quoted 9 lines
Quoted 8 lines
drivers/regulator/Kconfig
Quoted 6 lines
drivers/regulator/Kconfig +5
-0+ ret = spmi_controller_add(ctrl); + if (ret) + goto err_add_controller; + + dev_info(&pdev->dev, "spmi_add_controller initialized\n");Too noisy.
Quoted 3 lines
That's helpful to check if drivers initialized at the right order.
I'll change it to
dev_dbg().
More reasonable.
thanks,
Jonathan
Mauro Carvalho Chehab
maintainerEm Wed, 12 Aug 2020 09:43:53 +0100
Jonathan Cameron <[email protected]> escreveu:
Quoted 6 lines
Quoted 3 lines · On Wed, 12 Aug 2020 09:45:40 +0200 Mauro Carvalho Chehab…
Quoted 3 lines
This is mixing and matching managed an unmanaged. Should be one or the other or we might be hiding some race conditions.
Quoted 6 lines
I intended this as a more localized comment, though the following answers another question I had.
request_threaded_irqis not usingdevm_whilst the add devices is. As a result we might have a path in which the irq goes away before the device cleanup happens.
Ah, good point! I'll address it.
Quoted 39 lines
Quoted 31 lines
Actually, it is just the opposite. It took me a lot of time to figure out a good solution that will prevent all race conditions at probe time.
See, the SPMI variant of HiSilicon 6421 requires the drivers to be probed on a very specific order:
- The SPMI controller should be loaded first, as it provides the low-level I/O access to the serial bus used to talk with the PMICs. This bus is somewhat similar to the I2C bus.
Once the controller is registered, the SPMI bus probes the PMIC driver.
- Then, the MFD PMIC driver should be loaded. This adds support for a high level set of I/O operations, which are used by the regulator driver. Again, this approach is similar to the one taken by the I2C Kernel drivers.
- Finally, the regulator drivers should come, as they rely on the MFD I/O operations in order to talk with the SPMI bus.
The OOT driver probing was based on a some dirty hacks: it had an empty SPMI entry at the SoC, carrying on just the "compatible" line.
Then, another entry at DT with the real SPMI settings.
With such dirty hack, on Kernel 4.9, the PMIC driver were always loading before the regulator ones, as the SPMI bus code were serializing the probe there.
Quoted 7 lines
However, such settings were too fragile and broke after porting to upstream Kernels, because the regulator drivers were probed on a random order, typically before the MFD one (and sometimes even before the SPMI controller driver). Adding
EPROBE_DEFERdidn't solve all the issues, and made a complex and hard to debug scenario. Also, regulators were probed on a random order, making harder to debug issues there.
Quoted 3 lines
There are no ordering guarantees IIRC in mfd children coming up even in the normal path. It might currently happen in a particular order but relying on that seems fragile to me.
True, but in the case of SPMI controller and PMIC, there's no way to support them to be initialized on a random order.
That's why the approach I took is serializing the probe.
Quoted 39 lines
Quoted 39 lines
So, I ended using the same solution used by the already-existing
drivers/mfd/hi6421-pmic-core.cdriver[1].[1] This variant of the 6421 chipset is a lot simpler, as it doesn't use the SPMI bus.
With such approach, the probing is warranted to happen the way it is expected by the driver:
SPMI controller code starts:
[ 0.416862] spmi_controller fff24000.spmi: HISI SPMI probe [ 0.422419] spmi spmi-0: allocated controller 0x(____ptrval____) id 0 [ 0.428929] spmi_controller fff24000.spmi: spmi_add_controller base addr=0xffff800012055000! [ 0.437480] spmi spmi-0: adding child /spmi@fff24000/pmic@0 [ 0.443109] spmi spmi-0: read usid 00 [ 0.446821] spmi 2-00: device 2-00 registered [ 0.451220] spmi spmi-0: spmi-2 registered: dev:(____ptrval____) [ 0.457286] spmi_controller fff24000.spmi: spmi_add_controller initializedThe PMIC probe happens sometime after
spmi_controllerregisters itself at the SPMI bus:[ 1.955838] [hi6421_spmi_pmic_probe]. pmic->irqs[0] = 43 ... [ 2.036298] [hi6421_spmi_pmic_probe]. pmic->irqs[15] = 58After being ready to handle I/O requests, it starts probing the regulators:
[ 2.057815] hi6421v600-regulator hi6421v600-regulator: adding child /spmi@fff24000/pmic@0/regulators/ldo3@16 [ 2.199827] hi6421v600-regulator hi6421v600-regulator: adding child /spmi@fff24000/pmic@0/regulators/ldo4@17 [ 2.336284] hi6421v600-regulator hi6421v600-regulator: adding child /spmi@fff24000/pmic@0/regulators/ldo9@1C [ 2.472675] hi6421v600-regulator hi6421v600-regulator: adding child /spmi@fff24000/pmic@0/regulators/ldo15@21 [ 2.609402] hi6421v600-regulator hi6421v600-regulator: adding child /spmi@fff24000/pmic@0/regulators/ldo16@22 [ 2.746378] hi6421v600-regulator hi6421v600-regulator: adding child /spmi@fff24000/pmic@0/regulators/ldo17@23 [ 2.846707] hi6421v600-regulator hi6421v600-regulator: adding child /spmi@fff24000/pmic@0/regulators/ldo33@32 [ 2.988646] hi6421v600-regulator hi6421v600-regulator: adding child /spmi@fff24000/pmic@0/regulators/ldo34@33
Quoted 7 lines
Quoted 3 lines
As the current code serializes the regulator probing, it ensured that they'll happen at the right order, avoiding race conditions at probe time.
Why do we need the regulators to come up in a particular order?
That sounds suspicious as any relationships between different ones should be expressed either in DT or in the order they are enabled in the drivers using them.
There's no need for them to come up on a particular order.
What I meant to say is that the that the SPMI controller and MFD should go first.
-
Yet, incidentally, the current code also serializes the regulator probe. I could have written the code on a different way that would allow them to be probed in parallel, by moving a loop from the regulator driver to the PMIC one. However, I don't see any advantage on doing that, as the regulator initialization code ends calling the SPMI serial bus, whose access is already serialized by a spinlock.
So, there's no performance gain by allowing them to be probed in parallel, as most of the regulator's probing time is probably waiting for the relatively slow I/O serial transfers to happen.
Also, a nice a side effect of serializing the probe at the regulator driver is that the devices are ordered according their LDO numbers, and the debug logs from probing time will be altogether, helping to debug potential issues over there.
Quoted 18 lines
Quoted 11 lines
Quoted 11 lines
drivers/regulator/hi6421v600-regulator.c line 139
Quoted 8 lines
drivers/regulator/hi6421v600-regulator.c new file +8
-0+static int hi6421_spmi_regulator_set_voltage_sel (struct regulator_dev *rdev, +unsigned int selector) +{ +struct hi6421v600_regulator *sreg =rdev_get_drvdata (rdev); +struct hi6421_spmi_pmic *pmic = sreg->pmic; +u32 reg_val; + +/* unlikely to happen. sanity test done by regulator core */ Unlikely or can't?
Quoted 6 lines
Quoted 2 lines
Review
Quoted 2 lines
(quoted diff) +2
-0+ if (unlikely(selector >= rdev->desc->n_voltages)) + return -EINVAL;Good question. I almost removed this check, but I didn't check the regulator code with enough care to be 100% sure. So, I opted to keep it here.
Quoted 2 lines
I'd drop the comment then :) If someone else wants to figure it out in future then they are welcome to.
Ok.
Quoted 19 lines
Quoted 19 lines
Quoted 4 lines
drivers/regulator/hi6421v600-regulator.c line 215
Quoted 2 lines
drivers/regulator/hi6421v600-regulator.c new file +2
-0+if (load_uA || ((unsigned int )load_uA > sreg->eco_uA)) { +rdev_dbg (rdev,"normal mode" );Debug seems unnecessary to me, but maybe keep it if you want.
I actually used this debug. There are some LDO lines which don't support eco mode. The original driver was hard to understand that. So, I ended by re-writing the part of the code which sets/uses it[1]:
drivers/regulator/hi6421v600-regulator.c new file +9
-0+/* hisi regulator supports two modes */ + constraint = &initdata->constraints; + + constraint->valid_modes_mask =REGULATOR_MODE_NORMAL ; +if (sreg->eco_mode_mask) { + constraint->valid_modes_mask |=REGULATOR_MODE_IDLE ; + constraint->valid_ops_mask |=REGULATOR_CHANGE_MODE ; + } +
Quoted 8 lines
Quoted 4 lines
Those debug messages are useful to double-check if something bad is not happening with the modes/ops masks.
That's fine, but is it useful to have it upstream now you have debugged those issues? I'm not completely convinced it is and debug prints have a habit of rotting just like comments.
Good point. I'll do a review at the printks inside the driver anyway.
I'll try to cleanup some things that doesn't make much sense after having the driver working properly.
Thanks,
Mauro
Rob Herring
maintainerRe: [PATCH 31/33] dt: document HiSilicon SPMI controller and mfd/regulator properties
In reply to Mauro Carvalho ChehabQuoted 4 lines · Mauro Carvalho Chehab
Add documentation for the properties needed by the HiSilicon 6421v600 driver, and by the SPMI controller used to access the chipset.
Quoted 8 lines
Signed-off-by Mauro Carvalho Chehab <[email protected]>--- .../mfd/hisilicon,hi6421-spmi-pmic.yaml | 175 ++++++++++++++++++ .../spmi/hisilicon,hisi-spmi-controller.yaml | 54 ++++++ 2 files changed, 229 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml create mode 100644 Documentation/devicetree/bindings/spmi/hisilicon,hisi-spmi-controller.yaml
My bot found errors running 'make dt_binding_check' on your patch:
Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml: $id: relative path/filename doesn't match actual path or filename
expected: http://devicetree.org/schemas/mfd/hisilicon,hi6421-spmi-pmic.yaml#
Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.example.dts:34.15-28: Warning (reg_format): /example-0/pmic@0/regulators/ldo3@16:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.example.dts:57.15-28: Warning (reg_format): /example-0/pmic@0/regulators/ldo4@17:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.example.dt.yaml: Warning (pci_device_reg): Failed prerequisite 'reg_format' Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.example.dt.yaml: Warning (pci_device_bus_num): Failed prerequisite 'reg_format' Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.example.dt.yaml: Warning (simple_bus_reg): Failed prerequisite 'reg_format' Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.example.dt.yaml: Warning (i2c_bus_reg): Failed prerequisite 'reg_format' Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.example.dt.yaml: Warning (spi_bus_reg): Failed prerequisite 'reg_format' Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.example.dts:33.27-54.15: Warning (avoid_default_addr_size): /example-0/pmic@0/regulators/ldo3@16: Relying on default #address-cells value Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.example.dts:33.27-54.15: Warning (avoid_default_addr_size): /example-0/pmic@0/regulators/ldo3@16: Relying on default #size-cells value Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.example.dts:56.27-76.15: Warning (avoid_default_addr_size): /example-0/pmic@0/regulators/ldo4@17: Relying on default #address-cells value Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.example.dts:56.27-76.15: Warning (avoid_default_addr_size): /example-0/pmic@0/regulators/ldo4@17: Relying on default #size-cells value Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.example.dt.yaml: Warning (unique_unit_address): Failed prerequisite 'avoid_default_addr_size' /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spmi/hisilicon,hisi-spmi-controller.example.dt.yaml: example-0: spmi@fff24000:reg:0: [0, 4294066176, 0, 4096] is too long /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spmi/hisilicon,hisi-spmi-controller.example.dt.yaml: spmi@fff24000: spmi-channel:0: 'number of the SPMI channel where the PMIC is connected' was expected /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.example.dt.yaml: pmic@0: 'spmi-channel' is a required property
See https://patchwork.ozlabs.org/patch/1343370
If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure dt-schema is up to date:
pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade
Please check and re-submit.
Mauro Carvalho Chehab
maintainerRe: [PATCH 31/33] dt: document HiSilicon SPMI controller and mfd/regulator properties
Em Wed, 12 Aug 2020 10:30:36 -0600
Rob Herring <[email protected]> escreveu:
Quoted 36 lines · Mauro Carvalho Chehab
Quoted 4 lines
Add documentation for the properties needed by the HiSilicon 6421v600 driver, and by the SPMI controller used to access the chipset.
Quoted 8 lines
Signed-off-by Mauro Carvalho Chehab <[email protected]>--- .../mfd/hisilicon,hi6421-spmi-pmic.yaml | 175 ++++++++++++++++++ .../spmi/hisilicon,hisi-spmi-controller.yaml | 54 ++++++ 2 files changed, 229 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml create mode 100644 Documentation/devicetree/bindings/spmi/hisilicon,hisi-spmi-controller.yamlMy bot found errors running 'make
dt_binding_check' on your patch:
Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml: $id: relative path/filename doesn't match actual path or filename
expected: http://devicetree.org/schemas/mfd/hisilicon,hi6421-spmi-pmic.yaml#
Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.example.dts:34.15-28: Warning (reg_format): /example-0/pmic@0/regulators/ldo3@16:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.example.dts:57.15-28: Warning (reg_format): /example-0/pmic@0/regulators/ldo4@17:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.example.dt.yaml: Warning (pci_device_reg): Failed prerequisite 'reg_format'Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.example.dt.yaml: Warning (pci_device_bus_num): Failed prerequisite 'reg_format'Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.example.dt.yaml: Warning (simple_bus_reg): Failed prerequisite 'reg_format'Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.example.dt.yaml: Warning (i2c_bus_reg): Failed prerequisite 'reg_format'Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.example.dt.yaml: Warning (spi_bus_reg): Failed prerequisite 'reg_format' Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.example.dts:33.27-54.15: Warning (avoid_default_addr_size): /example-0/pmic@0/regulators/ldo3@16: Relying on default #address-cells value Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.example.dts:33.27-54.15: Warning (avoid_default_addr_size): /example-0/pmic@0/regulators/ldo3@16: Relying on default #size-cells value Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.example.dts:56.27-76.15: Warning (avoid_default_addr_size): /example-0/pmic@0/regulators/ldo4@17: Relying on default #address-cells value Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.example.dts:56.27-76.15: Warning (avoid_default_addr_size): /example-0/pmic@0/regulators/ldo4@17: Relying on default #size-cells valueDocumentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.example.dt.yaml: Warning (unique_unit_address): Failed prerequisite 'avoid_default_addr_size' /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spmi/hisilicon,hisi-spmi-controller.example.dt.yaml: example-0: spmi@fff24000:reg:0: [0, 4294066176, 0, 4096] is too long /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spmi/hisilicon,hisi-spmi-controller.example.dt.yaml: spmi@fff24000: spmi-channel:0: 'number of the SPMI channel where the PMIC is connected' was expected /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.example.dt.yaml: pmic@0: 'spmi-channel' is a required property
Quoted 9 lines
See https://patchwork.ozlabs.org/patch/1343370
If you already ran 'make
dt_binding_check' and didn't see the above error(s), then make sure dt-schema is up to date:pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade
Please check and re-submit.
Hi Rob,
Fixed those at the newest version I submitted today via staging tree.
At least here, dt_binding_check passes at the newest version.
Regards,
Mauro