Add hwmon driver for Moortec PVT controller

PVT controller (MR75203) is used to configure & control Moortec embedded analog IP which contains temprature sensor(TS), voltage monitor(VM) & process detector(PD) modules. Add hardware monitoring driver to support MR75203 PVT controller.

Signed-off-by Rahul Tanwar <[email protected]>

---
 drivers/hwmon/Kconfig   |  10 +
 drivers/hwmon/Makefile  |   1 +
 drivers/hwmon/mr75203.c | 651 ++++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 662 insertions(+)
 create mode 100644 drivers/hwmon/mr75203.c

drivers/hwmon/Kconfig +10 -0

index 8dc28b26916e..2defb46677b4 100644
@@ -1112,6 +1112,16 @@ config SENSORS_MENF21BMC_HWMON
 	  This driver can also be built as a module. If so the module
 	  will be called menf21bmc_hwmon.
 
+config SENSORS_MR75203
+	tristate "Moortec Semiconductor MR75203 PVT Controller"
+	select REGMAP_MMIO
+	help
+	  If you say yes here you get support for Moortec MR75203
+	  PVT controller.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called mr75203.
+
 config SENSORS_ADCXX
 	tristate "National Semiconductor ADCxxxSxxx"
 	depends on SPI_MASTER

drivers/hwmon/Makefile +1 -0

index a8f4b35b136b..bb4bd92a5149 100644
@@ -142,6 +142,7 @@ obj-$(CONFIG_SENSORS_MCP3021)	+= mcp3021.o
 obj-$(CONFIG_SENSORS_TC654)	+= tc654.o
 obj-$(CONFIG_SENSORS_MLXREG_FAN) += mlxreg-fan.o
 obj-$(CONFIG_SENSORS_MENF21BMC_HWMON) += menf21bmc_hwmon.o
+obj-$(CONFIG_SENSORS_MR75203)	+= mr75203.o
 obj-$(CONFIG_SENSORS_NCT6683)	+= nct6683.o
 obj-$(CONFIG_SENSORS_NCT6775)	+= nct6775.o
 obj-$(CONFIG_SENSORS_NCT7802)	+= nct7802.o

drivers/hwmon/mr75203.c new file +651 -0

new file mode 100644
index 000000000000..dc6f411ae873
@@ -0,0 +1,651 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 MaxLinear, Inc.
+ *
+ * This driver is a hardware monitoring driver for PVT controller
+ * (MR75203) which is used to configure & control Moortec embedded
+ * analog IP to enable multiple embedded temperature sensor(TS),
+ * voltage monitor(VM) & process detector(PD) modules.
+ */
+#include <linux/clk.h>
+#include <linux/hwmon.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/mutex.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+/* PVT Common register */
+#define PVT_IP_CONFIG	0x04
+#define TS_NUM_MSK	GENMASK(4, 0)
+#define TS_NUM_SFT	0
+#define PD_NUM_MSK	GENMASK(12, 8)
+#define PD_NUM_SFT	8
+#define VM_NUM_MSK	GENMASK(20, 16)
+#define VM_NUM_SFT	16
+#define CH_NUM_MSK	GENMASK(31, 24)
+#define CH_NUM_SFT	24
+
+/* Macro Common Register */
+#define CLK_SYNTH		0x00
+#define CLK_SYNTH_LO_SFT	0
+#define CLK_SYNTH_HI_SFT	8
+#define CLK_SYNTH_HOLD_SFT	16
+#define CLK_SYNTH_EN		BIT(24)
+#define CLK_SYS_CYCLES_MAX	514
+#define CLK_SYS_CYCLES_MIN	2
+#define HZ_PER_MHZ		1000000L
+
+#define SDIF_DISABLE	0x04
+
+#define SDIF_STAT	0x08
+#define SDIF_BUSY	BIT(0)
+#define SDIF_LOCK	BIT(1)
+
+#define SDIF_W		0x0c
+#define SDIF_PROG	BIT(31)
+#define SDIF_WRN_W	BIT(27)
+#define SDIF_WRN_R	0x00
+#define SDIF_ADDR_SFT	24
+
+#define SDIF_HALT	0x10
+#define SDIF_CTRL	0x14
+#define SDIF_SMPL_CTRL	0x20
+
+/* TS & PD Individual Macro Register */
+#define COM_REG_SIZE	0x40
+
+#define SDIF_DONE(n)	(COM_REG_SIZE + 0x14 + 0x40 * (n))
+#define SDIF_SMPL_DONE	BIT(0)
+
+#define SDIF_DATA(n)	(COM_REG_SIZE + 0x18 + 0x40 * (n))
+#define SAMPLE_DATA_MSK	GENMASK(15, 0)
+
+#define HILO_RESET(n)	(COM_REG_SIZE + 0x2c + 0x40 * (n))
+
+/* VM Individual Macro Register */
+#define VM_COM_REG_SIZE	0x200
+#define VM_SDIF_DONE(n)	(VM_COM_REG_SIZE + 0x34 + 0x200 * (n))
+#define VM_SDIF_DATA(n)	(VM_COM_REG_SIZE + 0x40 + 0x200 * (n))
+
+/* SDA Slave Register */
+#define IP_CTRL			0x00
+#define IP_RST_REL		BIT(1)
+#define IP_RUN_CONT		BIT(3)
+#define IP_AUTO			BIT(8)
+#define IP_VM_MODE		BIT(10)
+
+#define IP_CFG			0x01
+#define CFG0_MODE_2		BIT(0)
+#define CFG0_PARALLEL_OUT	0
+#define CFG0_12_BIT		0
+#define CFG1_VOL_MEAS_MODE	0
+#define CFG1_PARALLEL_OUT	0
+#define CFG1_14_BIT		0
+
+#define IP_DATA		0x03
+
+#define IP_POLL		0x04
+#define VM_CH_INIT	BIT(20)
+#define VM_CH_REQ	BIT(21)
+
+#define IP_TMR			0x05
+#define POWER_DELAY_CYCLE_256	0x80
+#define POWER_DELAY_CYCLE_64	0x40
+
+#define PVT_POLL_DELAY_US	20
+#define PVT_POLL_TIMEOUT_US	20000
+#define PVT_H_CONST		100000
+#define PVT_CAL5_CONST		2047
+#define PVT_G_CONST		40000
+#define PVT_CONV_BITS		10
+#define PVT_N_CONST		90
+#define PVT_R_CONST		245805
+
+struct pvt_device {
+	struct regmap		*c_map;
+	struct regmap		*t_map;
+	struct regmap		*p_map;
+	struct regmap		*v_map;
+	struct clk		*clk;
+	struct reset_control	*rst;
+	u32			t_num;
+	u32			p_num;
+	u32			v_num;
+	u32			ip_freq;
+	u8			*vm_idx;
+};
+
+static umode_t pvt_is_visible(const void *data, enum hwmon_sensor_types type,
+			      u32 attr, int channel)
+{
+	switch (type) {
+	case hwmon_temp:
+		if (attr == hwmon_temp_input)
+			return 0444;
+		return 0;
+	case hwmon_in:
+		if (attr == hwmon_in_input)
+			return 0444;
+		return 0;
+	default:
+		return 0;
+	}
+}
+
+static int pvt_read_temp(struct device *dev, u32 attr, int channel, long *val)
+{
+	struct pvt_device *pvt = dev_get_drvdata(dev);
+	struct regmap *t_map = pvt->t_map;
+	u32 stat, nbs;
+	int ret;
+	u64 tmp;
+
+	switch (attr) {
+	case hwmon_temp_input:
+		ret = regmap_read_poll_timeout(t_map, SDIF_DONE(channel),
+					       stat, stat & SDIF_SMPL_DONE,
+					       PVT_POLL_DELAY_US,
+					       PVT_POLL_TIMEOUT_US);
+		if (ret)
+			return ret;
+
+		ret = regmap_read(t_map, SDIF_DATA(channel), &nbs);
+		if(ret < 0)
+			return ret;
+
+		nbs &= SAMPLE_DATA_MSK;
+
+		/*
+		 * Convert the register value to
+		 * degrees centigrade temperature
+		 */
+		tmp = nbs * PVT_H_CONST;
+		do_div(tmp, PVT_CAL5_CONST);
+		*val = tmp - PVT_G_CONST - pvt->ip_freq;
+
+		return 0;
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+static int pvt_read_in(struct device *dev, u32 attr, int channel, long *val)
+{
+	struct pvt_device *pvt = dev_get_drvdata(dev);
+	struct regmap *v_map = pvt->v_map;
+	u32 n, stat;
+	u8 vm_idx;
+	int ret;
+
+	if (channel >= pvt->v_num)
+		return -EINVAL;
+
+	vm_idx = pvt->vm_idx[channel];
+
+	switch (attr) {
+	case hwmon_in_input:
+		ret = regmap_read_poll_timeout(v_map, VM_SDIF_DONE(vm_idx),
+					       stat, stat & SDIF_SMPL_DONE,
+					       PVT_POLL_DELAY_US,
+					       PVT_POLL_TIMEOUT_US);
+		if (ret)
+			return ret;
+
+		ret = regmap_read(v_map, VM_SDIF_DATA(vm_idx), &n);
+		if(ret < 0)
+			return ret;
+
+		n &= SAMPLE_DATA_MSK;
+		/* Convert the N bitstream count into voltage */
+		*val = (PVT_N_CONST * n - PVT_R_CONST) >> PVT_CONV_BITS;
+
+		return 0;
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+static int pvt_read(struct device *dev, enum hwmon_sensor_types type,
+		    u32 attr, int channel, long *val)
+{
+	switch (type) {
+	case hwmon_temp:
+		return pvt_read_temp(dev, attr, channel, val);
+	case hwmon_in:
+		return pvt_read_in(dev, attr, channel, val);
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+static const u32 pvt_chip_config[] = {
+	HWMON_C_REGISTER_TZ,
+	0
+};
+
+static const struct hwmon_channel_info pvt_chip = {
+	.type = hwmon_chip,
+	.config = pvt_chip_config,
+};
+
+static struct hwmon_channel_info pvt_temp = {
+	.type = hwmon_temp,
+};
+
+static struct hwmon_channel_info pvt_in = {
+	.type = hwmon_in,
+};
+
+static const struct hwmon_ops pvt_hwmon_ops = {
+	.is_visible = pvt_is_visible,
+	.read = pvt_read,
+};
+
+static struct hwmon_chip_info pvt_chip_info = {
+	.ops = &pvt_hwmon_ops,
+};
+
+static int pvt_init(struct pvt_device *pvt)
+{
+	u16 sys_freq, key, middle, low = 4, high = 8;
+	struct regmap *t_map = pvt->t_map;
+	struct regmap *p_map = pvt->p_map;
+	struct regmap *v_map = pvt->v_map;
+	u32 t_num = pvt->t_num;
+	u32 p_num = pvt->p_num;
+	u32 v_num = pvt->v_num;
+	u32 clk_synth, val;
+	int ret;
+
+	sys_freq = clk_get_rate(pvt->clk) / HZ_PER_MHZ;
+	while (high >= low) {
+		middle = (low + high + 1) / 2;
+		key = DIV_ROUND_CLOSEST(sys_freq, middle);
+		if (key > CLK_SYS_CYCLES_MAX) {
+			low = middle + 1;
+			continue;
+		} else if (key < CLK_SYS_CYCLES_MIN) {
+			high = middle - 1;
+			continue;
+		}
+
+		break;
+	}
+
+	/*
+	 * The system supports 'clk_sys' to 'clk_ip' frequency ratios
+	 * from 2:1 to 512:1
+	 */
+	key = clamp_val(key, CLK_SYS_CYCLES_MIN, CLK_SYS_CYCLES_MAX) - 2;
+
+	clk_synth = ((key + 1) >> 1) << CLK_SYNTH_LO_SFT |
+		    (key >> 1) << CLK_SYNTH_HI_SFT |
+		    (key >> 1) << CLK_SYNTH_HOLD_SFT | CLK_SYNTH_EN;
+
+	pvt->ip_freq = sys_freq * 100 / (key + 2);
+
+	if (t_num) {
+		ret = regmap_write(t_map, SDIF_SMPL_CTRL, 0x0);
+		if(ret < 0)
+			return ret;
+
+		ret = regmap_write(t_map, SDIF_HALT, 0x0);
+		if(ret < 0)
+			return ret;
+
+		ret = regmap_write(t_map, CLK_SYNTH, clk_synth);
+		if(ret < 0)
+			return ret;
+
+		ret = regmap_write(t_map, SDIF_DISABLE, 0x0);
+		if(ret < 0)
+			return ret;
+
+		ret = regmap_read_poll_timeout(t_map, SDIF_STAT,
+					       val, !(val & SDIF_BUSY),
+					       PVT_POLL_DELAY_US,
+					       PVT_POLL_TIMEOUT_US);
+		if (ret)
+			return ret;
+
+		val = CFG0_MODE_2 | CFG0_PARALLEL_OUT | CFG0_12_BIT |
+		      IP_CFG << SDIF_ADDR_SFT | SDIF_WRN_W | SDIF_PROG;
+		ret = regmap_write(t_map, SDIF_W, val);
+		if(ret < 0)
+			return ret;
+
+		ret = regmap_read_poll_timeout(t_map, SDIF_STAT,
+					       val, !(val & SDIF_BUSY),
+					       PVT_POLL_DELAY_US,
+					       PVT_POLL_TIMEOUT_US);
+		if (ret)
+			return ret;
+
+		val = POWER_DELAY_CYCLE_256 | IP_TMR << SDIF_ADDR_SFT |
+			      SDIF_WRN_W | SDIF_PROG;
+		ret = regmap_write(t_map, SDIF_W, val);
+		if(ret < 0)
+			return ret;
+
+		ret = regmap_read_poll_timeout(t_map, SDIF_STAT,
+					       val, !(val & SDIF_BUSY),
+					       PVT_POLL_DELAY_US,
+					       PVT_POLL_TIMEOUT_US);
+		if (ret)
+			return ret;
+
+		val = IP_RST_REL | IP_RUN_CONT | IP_AUTO |
+		      IP_CTRL << SDIF_ADDR_SFT |
+		      SDIF_WRN_W | SDIF_PROG;
+		ret = regmap_write(t_map, SDIF_W, val);
+		if(ret < 0)
+			return ret;
+	}
+
+	if (p_num) {
+		ret = regmap_write(p_map, SDIF_HALT, 0x0);
+		if(ret < 0)
+			return ret;
+
+		ret = regmap_write(p_map, SDIF_DISABLE, BIT(p_num) - 1);
+		if(ret < 0)
+			return ret;
+
+		ret = regmap_write(p_map, CLK_SYNTH, clk_synth);
+		if(ret < 0)
+			return ret;
+	}
+
+	if (v_num) {
+		ret = regmap_write(v_map, SDIF_SMPL_CTRL, 0x0);
+		if(ret < 0)
+			return ret;
+
+		ret = regmap_write(v_map, SDIF_HALT, 0x0);
+		if(ret < 0)
+			return ret;
+
+		ret = regmap_write(v_map, CLK_SYNTH, clk_synth);
+		if(ret < 0)
+			return ret;
+
+		ret = regmap_write(v_map, SDIF_DISABLE, 0x0);
+		if(ret < 0)
+			return ret;
+
+		ret = regmap_read_poll_timeout(v_map, SDIF_STAT,
+					       val, !(val & SDIF_BUSY),
+					       PVT_POLL_DELAY_US,
+					       PVT_POLL_TIMEOUT_US);
+		if (ret)
+			return ret;
+
+		val = CFG1_VOL_MEAS_MODE | CFG1_PARALLEL_OUT |
+		      CFG1_14_BIT | IP_CFG << SDIF_ADDR_SFT |
+		      SDIF_WRN_W | SDIF_PROG;
+		ret = regmap_write(v_map, SDIF_W, val);
+		if(ret < 0)
+			return ret;
+
+		ret = regmap_read_poll_timeout(v_map, SDIF_STAT,
+					       val, !(val & SDIF_BUSY),
+					       PVT_POLL_DELAY_US,
+					       PVT_POLL_TIMEOUT_US);
+		if (ret)
+			return ret;
+
+		val = POWER_DELAY_CYCLE_64 | IP_TMR << SDIF_ADDR_SFT |
+		      SDIF_WRN_W | SDIF_PROG;
+		ret = regmap_write(v_map, SDIF_W, val);
+		if(ret < 0)
+			return ret;
+
+		ret = regmap_read_poll_timeout(v_map, SDIF_STAT,
+					       val, !(val & SDIF_BUSY),
+					       PVT_POLL_DELAY_US,
+					       PVT_POLL_TIMEOUT_US);
+		if (ret)
+			return ret;
+
+		val = IP_RST_REL | IP_RUN_CONT | IP_AUTO | IP_VM_MODE |
+		      IP_CTRL << SDIF_ADDR_SFT |
+		      SDIF_WRN_W | SDIF_PROG;
+		ret = regmap_write(v_map, SDIF_W, val);
+		if(ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+static struct regmap_config pvt_regmap_config = {
+	.reg_bits = 32,
+	.reg_stride = 4,
+	.val_bits = 32,
+};
+
+static int pvt_get_regmap(struct platform_device *pdev, char *reg_name,
+			  struct pvt_device *pvt)
+{
+	struct device *dev = &pdev->dev;
+	struct regmap **reg_map;
+	void __iomem *io_base;
+
+	if (!strcmp(reg_name, "common"))
+		reg_map = &pvt->c_map;
+	else if (!strcmp(reg_name, "ts"))
+		reg_map = &pvt->t_map;
+	else if (!strcmp(reg_name, "pd"))
+		reg_map = &pvt->p_map;
+	else if (!strcmp(reg_name, "vm"))
+		reg_map = &pvt->v_map;
+	else
+		return -EINVAL;
+
+	io_base = devm_platform_ioremap_resource_byname(pdev, reg_name);
+	if (IS_ERR(io_base))
+		return PTR_ERR(io_base);
+
+	pvt_regmap_config.name = reg_name;
+	*reg_map = devm_regmap_init_mmio(dev, io_base, &pvt_regmap_config);
+	if (IS_ERR(*reg_map)) {
+		dev_err(dev, "failed to init register map\n");
+		return PTR_ERR(*reg_map);
+	}
+
+	return 0;
+}
+
+static void pvt_clk_disable(void *data)
+{
+	struct pvt_device *pvt = data;
+
+	clk_disable_unprepare(pvt->clk);
+}
+
+static int pvt_clk_enable(struct device *dev, struct pvt_device *pvt)
+{
+	int ret;
+
+	ret = clk_prepare_enable(pvt->clk);
+	if (ret)
+		return ret;
+
+	return devm_add_action_or_reset(dev, pvt_clk_disable, pvt);
+}
+
+static void pvt_reset_control_assert(void *data)
+{
+	struct pvt_device *pvt = data;
+
+	reset_control_assert(pvt->rst);
+}
+
+static int pvt_reset_control_deassert(struct device *dev, struct pvt_device *pvt)
+{
+	int ret;
+
+	ret = reset_control_deassert(pvt->rst);
+	if (ret)
+		return ret;
+
+	return devm_add_action_or_reset(dev, pvt_reset_control_assert, pvt);
+}
+
+static int mr75203_probe(struct platform_device *pdev)
+{
+	const struct hwmon_channel_info **pvt_info;
+	u32 ts_num, vm_num, pd_num, val, index, i;
+	struct device *dev = &pdev->dev;
+	u32 *temp_config, *in_config;
+	struct device *hwmon_dev;
+	struct pvt_device *pvt;
+	int ret;
+
+	pvt = devm_kzalloc(dev, sizeof(*pvt), GFP_KERNEL);
+	if (!pvt)
+		return -ENOMEM;
+
+	ret = pvt_get_regmap(pdev, "common", pvt);
+	if (ret)
+		return ret;
+
+	pvt->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(pvt->clk))
+		return dev_err_probe(dev, PTR_ERR(pvt->clk), "failed to get clock\n");
+
+	ret = pvt_clk_enable(dev, pvt);
+	if (ret) {
+		dev_err(dev, "failed to enable clock\n");
+		return ret;
+	}
+
+	pvt->rst = devm_reset_control_get_exclusive(dev, NULL);
+	if (IS_ERR(pvt->rst))
+		return dev_err_probe(dev, PTR_ERR(pvt->rst),
+				     "failed to get reset control\n");
+
+	ret = pvt_reset_control_deassert(dev, pvt);
+	if (ret)
+		return dev_err_probe(dev, ret, "cannot deassert reset control\n");
+
+	ret = regmap_read(pvt->c_map, PVT_IP_CONFIG, &val);
+	if(ret < 0)
+		return ret;
+
+	ts_num = (val & TS_NUM_MSK) >> TS_NUM_SFT;
+	pd_num = (val & PD_NUM_MSK) >> PD_NUM_SFT;
+	vm_num = (val & VM_NUM_MSK) >> VM_NUM_SFT;
+	pvt->t_num = ts_num;
+	pvt->p_num = pd_num;
+	pvt->v_num = vm_num;
+	val = 0;
+	if (ts_num)
+		val++;
+	if (vm_num)
+		val++;
+	if (!val)
+		return -ENODEV;
+
+	pvt_info = devm_kcalloc(dev, val + 2, sizeof(*pvt_info), GFP_KERNEL);
+	if (!pvt_info)
+		return -ENOMEM;
+	pvt_info[0] = &pvt_chip;
+	index = 1;
+
+	if (ts_num) {
+		ret = pvt_get_regmap(pdev, "ts", pvt);
+		if (ret)
+			return ret;
+
+		temp_config = devm_kcalloc(dev, ts_num + 1,
+					   sizeof(*temp_config), GFP_KERNEL);
+		if (!temp_config)
+			return -ENOMEM;
+
+		for (i = 0; i < ts_num; i++)
+			temp_config[i] = HWMON_T_INPUT;
+
+		temp_config[ts_num] = 0;
+		pvt_temp.config = temp_config;
+
+		pvt_info[index++] = &pvt_temp;
+	}
+
+	if (pd_num) {
+		ret = pvt_get_regmap(pdev, "pd", pvt);
+		if (ret)
+			return ret;
+	}
+
+	if (vm_num) {
+		u32 num = vm_num;
+
+		ret = pvt_get_regmap(pdev, "vm", pvt);
+		if (ret)
+			return ret;
+
+		pvt->vm_idx = devm_kcalloc(dev, vm_num, sizeof(*pvt->vm_idx),
+					   GFP_KERNEL);
+		if (!pvt->vm_idx)
+			return -ENOMEM;
+
+		for (i = 0; i < vm_num; i++)
+			pvt->vm_idx[i] = i;
+
+		ret = device_property_read_u8_array(dev, "intel,vm-map",
+						    pvt->vm_idx, vm_num);
+		if (!ret)
+			for (i = 0; i < vm_num; i++)
+				if (pvt->vm_idx[i] >= vm_num ||
+				    pvt->vm_idx[i] == 0xff) {
+					num = i;
+					break;
+				}
+
+		in_config = devm_kcalloc(dev, num + 1,
+					 sizeof(*in_config), GFP_KERNEL);
+		if (!in_config)
+			return -ENOMEM;
+
+		memset32(in_config, HWMON_I_INPUT, num);
+		in_config[num] = 0;
+		pvt_in.config = in_config;
+
+		pvt_info[index++] = &pvt_in;
+	}
+
+	ret = pvt_init(pvt);
+	if (ret) {
+		dev_err(dev, "failed to init pvt: %d\n", ret);
+		return ret;
+	}
+
+	pvt_chip_info.info = pvt_info;
+	hwmon_dev = devm_hwmon_device_register_with_info(dev, "pvt",
+							 pvt,
+							 &pvt_chip_info,
+							 NULL);
+
+	return PTR_ERR_OR_ZERO(hwmon_dev);
+}
+
+static const struct of_device_id moortec_pvt_of_match[] = {
+	{ .compatible = "moortec,mr75203" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, moortec_pvt_of_match);
+
+static struct platform_driver moortec_pvt_driver = {
+	.driver = {
+		.name = "moortec-pvt",
+		.of_match_table = moortec_pvt_of_match,
+	},
+	.probe = mr75203_probe,
+};
+module_platform_driver(moortec_pvt_driver);
+
+MODULE_LICENSE("GPL v2");

PVT controller (MR75203) is used to configure & control Moortec embedded analog IP which contains temprature sensor(TS), voltage monitor(VM) & process detector(PD) modules. Add hardware monitoring driver to support MR75203 PVT controller.

Signed-off-by Rahul Tanwar <[email protected]>

---
 drivers/hwmon/Kconfig   |  10 +
 drivers/hwmon/Makefile  |   1 +
 drivers/hwmon/mr75203.c | 651 ++++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 662 insertions(+)
 create mode 100644 drivers/hwmon/mr75203.c

drivers/hwmon/Kconfig +10 -0

index 8dc28b26916e..2defb46677b4 100644
@@ -1112,6 +1112,16 @@ config SENSORS_MENF21BMC_HWMON
 	  This driver can also be built as a module. If so the module
 	  will be called menf21bmc_hwmon.
 
+config SENSORS_MR75203
+	tristate "Moortec Semiconductor MR75203 PVT Controller"
+	select REGMAP_MMIO
+	help
+	  If you say yes here you get support for Moortec MR75203
+	  PVT controller.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called mr75203.
+
 config SENSORS_ADCXX
 	tristate "National Semiconductor ADCxxxSxxx"
 	depends on SPI_MASTER

drivers/hwmon/Makefile +1 -0

index a8f4b35b136b..bb4bd92a5149 100644
@@ -142,6 +142,7 @@ obj-$(CONFIG_SENSORS_MCP3021)	+= mcp3021.o
 obj-$(CONFIG_SENSORS_TC654)	+= tc654.o
 obj-$(CONFIG_SENSORS_MLXREG_FAN) += mlxreg-fan.o
 obj-$(CONFIG_SENSORS_MENF21BMC_HWMON) += menf21bmc_hwmon.o
+obj-$(CONFIG_SENSORS_MR75203)	+= mr75203.o
 obj-$(CONFIG_SENSORS_NCT6683)	+= nct6683.o
 obj-$(CONFIG_SENSORS_NCT6775)	+= nct6775.o
 obj-$(CONFIG_SENSORS_NCT7802)	+= nct7802.o

drivers/hwmon/mr75203.c new file +0 -0

new file mode 100644
index 000000000000..dc6f411ae873

drivers/hwmon/mr75203.c new file +119 -0

+#include <linux/clk.h>
+#include <linux/hwmon.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/mutex.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+/* PVT Common register */
+#define PVT_IP_CONFIG	0x04
+#define TS_NUM_MSK	GENMASK(4, 0)
+#define TS_NUM_SFT	0
+#define PD_NUM_MSK	GENMASK(12, 8)
+#define PD_NUM_SFT	8
+#define VM_NUM_MSK	GENMASK(20, 16)
+#define VM_NUM_SFT	16
+#define CH_NUM_MSK	GENMASK(31, 24)
+#define CH_NUM_SFT	24
+
+/* Macro Common Register */
+#define CLK_SYNTH		0x00
+#define CLK_SYNTH_LO_SFT	0
+#define CLK_SYNTH_HI_SFT	8
+#define CLK_SYNTH_HOLD_SFT	16
+#define CLK_SYNTH_EN		BIT(24)
+#define CLK_SYS_CYCLES_MAX	514
+#define CLK_SYS_CYCLES_MIN	2
+#define HZ_PER_MHZ		1000000L
+
+#define SDIF_DISABLE	0x04
+
+#define SDIF_STAT	0x08
+#define SDIF_BUSY	BIT(0)
+#define SDIF_LOCK	BIT(1)
+
+#define SDIF_W		0x0c
+#define SDIF_PROG	BIT(31)
+#define SDIF_WRN_W	BIT(27)
+#define SDIF_WRN_R	0x00
+#define SDIF_ADDR_SFT	24
+
+#define SDIF_HALT	0x10
+#define SDIF_CTRL	0x14
+#define SDIF_SMPL_CTRL	0x20
+
+/* TS & PD Individual Macro Register */
+#define COM_REG_SIZE	0x40
+
+#define SDIF_DONE(n)	(COM_REG_SIZE + 0x14 + 0x40 * (n))
+#define SDIF_SMPL_DONE	BIT(0)
+
+#define SDIF_DATA(n)	(COM_REG_SIZE + 0x18 + 0x40 * (n))
+#define SAMPLE_DATA_MSK	GENMASK(15, 0)
+
+#define HILO_RESET(n)	(COM_REG_SIZE + 0x2c + 0x40 * (n))
+
+/* VM Individual Macro Register */
+#define VM_COM_REG_SIZE	0x200
+#define VM_SDIF_DONE(n)	(VM_COM_REG_SIZE + 0x34 + 0x200 * (n))
+#define VM_SDIF_DATA(n)	(VM_COM_REG_SIZE + 0x40 + 0x200 * (n))
+
+/* SDA Slave Register */
+#define IP_CTRL			0x00
+#define IP_RST_REL		BIT(1)
+#define IP_RUN_CONT		BIT(3)
+#define IP_AUTO			BIT(8)
+#define IP_VM_MODE		BIT(10)
+
+#define IP_CFG			0x01
+#define CFG0_MODE_2		BIT(0)
+#define CFG0_PARALLEL_OUT	0
+#define CFG0_12_BIT		0
+#define CFG1_VOL_MEAS_MODE	0
+#define CFG1_PARALLEL_OUT	0
+#define CFG1_14_BIT		0
+
+#define IP_DATA		0x03
+
+#define IP_POLL		0x04
+#define VM_CH_INIT	BIT(20)
+#define VM_CH_REQ	BIT(21)
+
+#define IP_TMR			0x05
+#define POWER_DELAY_CYCLE_256	0x80
+#define POWER_DELAY_CYCLE_64	0x40
+
+#define PVT_POLL_DELAY_US	20
+#define PVT_POLL_TIMEOUT_US	20000
+#define PVT_H_CONST		100000
+#define PVT_CAL5_CONST		2047
+#define PVT_G_CONST		40000
+#define PVT_CONV_BITS		10
+#define PVT_N_CONST		90
+#define PVT_R_CONST		245805
+
+struct pvt_device {
+	struct regmap		*c_map;
+	struct regmap		*t_map;
+	struct regmap		*p_map;
+	struct regmap		*v_map;
+	struct clk		*clk;
+	struct reset_control	*rst;
+	u32			t_num;
+	u32			p_num;
+	u32			v_num;
+	u32			ip_freq;
+	u8			*vm_idx;
+};
+
+static umode_t pvt_is_visible(const void *data, enum hwmon_sensor_types type,
+			      u32 attr, int channel)
+{
+	switch (type) {
+	case hwmon_temp:
+		if (attr == hwmon_temp_input)
+			return 0444;
 
+		return 0;

drivers/hwmon/mr75203.c new file +133 -0

+}
+
+static int pvt_read_temp(struct device *dev, u32 attr, int channel, long *val)
+{
+	struct pvt_device *pvt = dev_get_drvdata(dev);
+	struct regmap *t_map = pvt->t_map;
+	u32 stat, nbs;
+	int ret;
+	u64 tmp;
+
+	switch (attr) {
+	case hwmon_temp_input:
+		ret = regmap_read_poll_timeout(t_map, SDIF_DONE(channel),
+					       stat, stat & SDIF_SMPL_DONE,
+					       PVT_POLL_DELAY_US,
+					       PVT_POLL_TIMEOUT_US);
+		if (ret)
+			return ret;
+
+		ret = regmap_read(t_map, SDIF_DATA(channel), &nbs);
+		if(ret < 0)
+			return ret;
+
+		nbs &= SAMPLE_DATA_MSK;
+
+		/*
+		 * Convert the register value to
+		 * degrees centigrade temperature
+		 */
+		tmp = nbs * PVT_H_CONST;
+		do_div(tmp, PVT_CAL5_CONST);
+		*val = tmp - PVT_G_CONST - pvt->ip_freq;
+
+		return 0;
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+static int pvt_read_in(struct device *dev, u32 attr, int channel, long *val)
+{
+	struct pvt_device *pvt = dev_get_drvdata(dev);
+	struct regmap *v_map = pvt->v_map;
+	u32 n, stat;
+	u8 vm_idx;
+	int ret;
+
+	if (channel >= pvt->v_num)
+		return -EINVAL;
+
+	vm_idx = pvt->vm_idx[channel];
+
+	switch (attr) {
+	case hwmon_in_input:
+		ret = regmap_read_poll_timeout(v_map, VM_SDIF_DONE(vm_idx),
+					       stat, stat & SDIF_SMPL_DONE,
+					       PVT_POLL_DELAY_US,
+					       PVT_POLL_TIMEOUT_US);
+		if (ret)
+			return ret;
+
+		ret = regmap_read(v_map, VM_SDIF_DATA(vm_idx), &n);
+		if(ret < 0)
+			return ret;
+
+		n &= SAMPLE_DATA_MSK;
+		/* Convert the N bitstream count into voltage */
+		*val = (PVT_N_CONST * n - PVT_R_CONST) >> PVT_CONV_BITS;
+
+		return 0;
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+static int pvt_read(struct device *dev, enum hwmon_sensor_types type,
+		    u32 attr, int channel, long *val)
+{
+	switch (type) {
+	case hwmon_temp:
+		return pvt_read_temp(dev, attr, channel, val);
+	case hwmon_in:
+		return pvt_read_in(dev, attr, channel, val);
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+static const u32 pvt_chip_config[] = {
+	HWMON_C_REGISTER_TZ,
+	0
+};
+
+static const struct hwmon_channel_info pvt_chip = {
+	.type = hwmon_chip,
+	.config = pvt_chip_config,
+};
+
+static struct hwmon_channel_info pvt_temp = {
+	.type = hwmon_temp,
+};
+
+static struct hwmon_channel_info pvt_in = {
+	.type = hwmon_in,
+};
+
+static const struct hwmon_ops pvt_hwmon_ops = {
+	.is_visible = pvt_is_visible,
+	.read = pvt_read,
+};
+
+static struct hwmon_chip_info pvt_chip_info = {
+	.ops = &pvt_hwmon_ops,
+};
+
+static int pvt_init(struct pvt_device *pvt)
+{
+	u16 sys_freq, key, middle, low = 4, high = 8;
+	struct regmap *t_map = pvt->t_map;
+	struct regmap *p_map = pvt->p_map;
+	struct regmap *v_map = pvt->v_map;
+	u32 t_num = pvt->t_num;
+	u32 p_num = pvt->p_num;
+	u32 v_num = pvt->v_num;
+	u32 clk_synth, val;
+	int ret;
+
+	sys_freq = clk_get_rate(pvt->clk) / HZ_PER_MHZ;
+	while (high >= low) {
+		middle = (low + high + 1) / 2;
+		key = DIV_ROUND_CLOSEST(sys_freq, middle);
+		if (key > CLK_SYS_CYCLES_MAX) {
+			low = middle + 1;
 

drivers/hwmon/mr75203.c new file +285 -0

+	}
+
+	/*
+	 * The system supports 'clk_sys' to 'clk_ip' frequency ratios
+	 * from 2:1 to 512:1
+	 */
+	key = clamp_val(key, CLK_SYS_CYCLES_MIN, CLK_SYS_CYCLES_MAX) - 2;
+
+	clk_synth = ((key + 1) >> 1) << CLK_SYNTH_LO_SFT |
+		    (key >> 1) << CLK_SYNTH_HI_SFT |
+		    (key >> 1) << CLK_SYNTH_HOLD_SFT | CLK_SYNTH_EN;
+
+	pvt->ip_freq = sys_freq * 100 / (key + 2);
+
+	if (t_num) {
+		ret = regmap_write(t_map, SDIF_SMPL_CTRL, 0x0);
+		if(ret < 0)
+			return ret;
+
+		ret = regmap_write(t_map, SDIF_HALT, 0x0);
+		if(ret < 0)
+			return ret;
+
+		ret = regmap_write(t_map, CLK_SYNTH, clk_synth);
+		if(ret < 0)
+			return ret;
+
+		ret = regmap_write(t_map, SDIF_DISABLE, 0x0);
+		if(ret < 0)
+			return ret;
+
+		ret = regmap_read_poll_timeout(t_map, SDIF_STAT,
+					       val, !(val & SDIF_BUSY),
+					       PVT_POLL_DELAY_US,
+					       PVT_POLL_TIMEOUT_US);
+		if (ret)
+			return ret;
+
+		val = CFG0_MODE_2 | CFG0_PARALLEL_OUT | CFG0_12_BIT |
+		      IP_CFG << SDIF_ADDR_SFT | SDIF_WRN_W | SDIF_PROG;
+		ret = regmap_write(t_map, SDIF_W, val);
+		if(ret < 0)
+			return ret;
+
+		ret = regmap_read_poll_timeout(t_map, SDIF_STAT,
+					       val, !(val & SDIF_BUSY),
+					       PVT_POLL_DELAY_US,
+					       PVT_POLL_TIMEOUT_US);
+		if (ret)
+			return ret;
+
+		val = POWER_DELAY_CYCLE_256 | IP_TMR << SDIF_ADDR_SFT |
+			      SDIF_WRN_W | SDIF_PROG;
+		ret = regmap_write(t_map, SDIF_W, val);
+		if(ret < 0)
+			return ret;
+
+		ret = regmap_read_poll_timeout(t_map, SDIF_STAT,
+					       val, !(val & SDIF_BUSY),
+					       PVT_POLL_DELAY_US,
+					       PVT_POLL_TIMEOUT_US);
+		if (ret)
+			return ret;
+
+		val = IP_RST_REL | IP_RUN_CONT | IP_AUTO |
+		      IP_CTRL << SDIF_ADDR_SFT |
+		      SDIF_WRN_W | SDIF_PROG;
+		ret = regmap_write(t_map, SDIF_W, val);
+		if(ret < 0)
+			return ret;
+	}
+
+	if (p_num) {
+		ret = regmap_write(p_map, SDIF_HALT, 0x0);
+		if(ret < 0)
+			return ret;
+
+		ret = regmap_write(p_map, SDIF_DISABLE, BIT(p_num) - 1);
+		if(ret < 0)
+			return ret;
+
+		ret = regmap_write(p_map, CLK_SYNTH, clk_synth);
+		if(ret < 0)
+			return ret;
+	}
+
+	if (v_num) {
+		ret = regmap_write(v_map, SDIF_SMPL_CTRL, 0x0);
+		if(ret < 0)
+			return ret;
+
+		ret = regmap_write(v_map, SDIF_HALT, 0x0);
+		if(ret < 0)
+			return ret;
+
+		ret = regmap_write(v_map, CLK_SYNTH, clk_synth);
+		if(ret < 0)
+			return ret;
+
+		ret = regmap_write(v_map, SDIF_DISABLE, 0x0);
+		if(ret < 0)
+			return ret;
+
+		ret = regmap_read_poll_timeout(v_map, SDIF_STAT,
+					       val, !(val & SDIF_BUSY),
+					       PVT_POLL_DELAY_US,
+					       PVT_POLL_TIMEOUT_US);
+		if (ret)
+			return ret;
+
+		val = CFG1_VOL_MEAS_MODE | CFG1_PARALLEL_OUT |
+		      CFG1_14_BIT | IP_CFG << SDIF_ADDR_SFT |
+		      SDIF_WRN_W | SDIF_PROG;
+		ret = regmap_write(v_map, SDIF_W, val);
+		if(ret < 0)
+			return ret;
+
+		ret = regmap_read_poll_timeout(v_map, SDIF_STAT,
+					       val, !(val & SDIF_BUSY),
+					       PVT_POLL_DELAY_US,
+					       PVT_POLL_TIMEOUT_US);
+		if (ret)
+			return ret;
+
+		val = POWER_DELAY_CYCLE_64 | IP_TMR << SDIF_ADDR_SFT |
+		      SDIF_WRN_W | SDIF_PROG;
+		ret = regmap_write(v_map, SDIF_W, val);
+		if(ret < 0)
+			return ret;
+
+		ret = regmap_read_poll_timeout(v_map, SDIF_STAT,
+					       val, !(val & SDIF_BUSY),
+					       PVT_POLL_DELAY_US,
+					       PVT_POLL_TIMEOUT_US);
+		if (ret)
+			return ret;
+
+		val = IP_RST_REL | IP_RUN_CONT | IP_AUTO | IP_VM_MODE |
+		      IP_CTRL << SDIF_ADDR_SFT |
+		      SDIF_WRN_W | SDIF_PROG;
+		ret = regmap_write(v_map, SDIF_W, val);
+		if(ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+static struct regmap_config pvt_regmap_config = {
+	.reg_bits = 32,
+	.reg_stride = 4,
+	.val_bits = 32,
+};
+
+static int pvt_get_regmap(struct platform_device *pdev, char *reg_name,
+			  struct pvt_device *pvt)
+{
+	struct device *dev = &pdev->dev;
+	struct regmap **reg_map;
+	void __iomem *io_base;
+
+	if (!strcmp(reg_name, "common"))
+		reg_map = &pvt->c_map;
+	else if (!strcmp(reg_name, "ts"))
+		reg_map = &pvt->t_map;
+	else if (!strcmp(reg_name, "pd"))
+		reg_map = &pvt->p_map;
+	else if (!strcmp(reg_name, "vm"))
+		reg_map = &pvt->v_map;
+	else
+		return -EINVAL;
+
+	io_base = devm_platform_ioremap_resource_byname(pdev, reg_name);
+	if (IS_ERR(io_base))
+		return PTR_ERR(io_base);
+
+	pvt_regmap_config.name = reg_name;
+	*reg_map = devm_regmap_init_mmio(dev, io_base, &pvt_regmap_config);
+	if (IS_ERR(*reg_map)) {
+		dev_err(dev, "failed to init register map\n");
+		return PTR_ERR(*reg_map);
+	}
+
+	return 0;
+}
+
+static void pvt_clk_disable(void *data)
+{
+	struct pvt_device *pvt = data;
+
+	clk_disable_unprepare(pvt->clk);
+}
+
+static int pvt_clk_enable(struct device *dev, struct pvt_device *pvt)
+{
+	int ret;
+
+	ret = clk_prepare_enable(pvt->clk);
+	if (ret)
+		return ret;
+
+	return devm_add_action_or_reset(dev, pvt_clk_disable, pvt);
+}
+
+static void pvt_reset_control_assert(void *data)
+{
+	struct pvt_device *pvt = data;
+
+	reset_control_assert(pvt->rst);
+}
+
+static int pvt_reset_control_deassert(struct device *dev, struct pvt_device *pvt)
+{
+	int ret;
+
+	ret = reset_control_deassert(pvt->rst);
+	if (ret)
+		return ret;
+
+	return devm_add_action_or_reset(dev, pvt_reset_control_assert, pvt);
+}
+
+static int mr75203_probe(struct platform_device *pdev)
+{
+	const struct hwmon_channel_info **pvt_info;
+	u32 ts_num, vm_num, pd_num, val, index, i;
+	struct device *dev = &pdev->dev;
+	u32 *temp_config, *in_config;
+	struct device *hwmon_dev;
+	struct pvt_device *pvt;
+	int ret;
+
+	pvt = devm_kzalloc(dev, sizeof(*pvt), GFP_KERNEL);
+	if (!pvt)
+		return -ENOMEM;
+
+	ret = pvt_get_regmap(pdev, "common", pvt);
+	if (ret)
+		return ret;
+
+	pvt->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(pvt->clk))
+		return dev_err_probe(dev, PTR_ERR(pvt->clk), "failed to get clock\n");
+
+	ret = pvt_clk_enable(dev, pvt);
+	if (ret) {
+		dev_err(dev, "failed to enable clock\n");
+		return ret;
+	}
+
+	pvt->rst = devm_reset_control_get_exclusive(dev, NULL);
+	if (IS_ERR(pvt->rst))
+		return dev_err_probe(dev, PTR_ERR(pvt->rst),
+				     "failed to get reset control\n");
+
+	ret = pvt_reset_control_deassert(dev, pvt);
+	if (ret)
+		return dev_err_probe(dev, ret, "cannot deassert reset control\n");
+
+	ret = regmap_read(pvt->c_map, PVT_IP_CONFIG, &val);
+	if(ret < 0)
+		return ret;
+
+	ts_num = (val & TS_NUM_MSK) >> TS_NUM_SFT;
+	pd_num = (val & PD_NUM_MSK) >> PD_NUM_SFT;
+	vm_num = (val & VM_NUM_MSK) >> VM_NUM_SFT;
+	pvt->t_num = ts_num;
+	pvt->p_num = pd_num;
+	pvt->v_num = vm_num;
+	val = 0;
+	if (ts_num)
+		val++;
+	if (vm_num)
+		val++;
+	if (!val)
+		return -ENODEV;
+
+	pvt_info = devm_kcalloc(dev, val + 2, sizeof(*pvt_info), GFP_KERNEL);
+	if (!pvt_info)
+		return -ENOMEM;
+	pvt_info[0] = &pvt_chip;
+	index = 1;
+
+	if (ts_num) {
+		ret = pvt_get_regmap(pdev, "ts", pvt);

drivers/hwmon/mr75203.c new file +15 -0

+		pvt_temp.config = temp_config;
+
+		pvt_info[index++] = &pvt_temp;
+	}
+
+	if (pd_num) {
+		ret = pvt_get_regmap(pdev, "pd", pvt);
+		if (ret)
+			return ret;
+	}
+
+	if (vm_num) {
+		u32 num = vm_num;
+
+		ret = pvt_get_regmap(pdev, "vm", pvt);

drivers/hwmon/mr75203.c new file +44 -0

+
+		in_config = devm_kcalloc(dev, num + 1,
+					 sizeof(*in_config), GFP_KERNEL);
+		if (!in_config)
+			return -ENOMEM;
+
+		memset32(in_config, HWMON_I_INPUT, num);
+		in_config[num] = 0;
+		pvt_in.config = in_config;
+
+		pvt_info[index++] = &pvt_in;
+	}
+
+	ret = pvt_init(pvt);
+	if (ret) {
+		dev_err(dev, "failed to init pvt: %d\n", ret);
+		return ret;
+	}
+
+	pvt_chip_info.info = pvt_info;
+	hwmon_dev = devm_hwmon_device_register_with_info(dev, "pvt",
+							 pvt,
+							 &pvt_chip_info,
+							 NULL);
+
+	return PTR_ERR_OR_ZERO(hwmon_dev);
+}
+
+static const struct of_device_id moortec_pvt_of_match[] = {
+	{ .compatible = "moortec,mr75203" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, moortec_pvt_of_match);
+
+static struct platform_driver moortec_pvt_driver = {
+	.driver = {
+		.name = "moortec-pvt",
+		.of_match_table = moortec_pvt_of_match,
+	},
+	.probe = mr75203_probe,
+};
+module_platform_driver(moortec_pvt_driver);
+
+MODULE_LICENSE("GPL v2");

Signature · 1 line

2.11.0

On Fri, Oct 02, 2020 at 03:04:27PM +0800, Rahul Tanwar wrote:

Quoted 7 lines

drivers/hwmon/mr75203.c new file +5 -0

+	case hwmon_in:
+		if (attr == hwmon_in_input)
+			return 0444;
 
+		return 0;
 
+	default:

Review

Quoted 1 line

(quoted diff) +1 -0

+		return 0;

break here and

Review

Quoted 1 line

(quoted diff) +1 -0

+	}

return 0; here only once.

Quoted 5 lines · Rahul Tanwar

PVT controller (MR75203) is used to configure & control Moortec embedded analog IP which contains temprature sensor(TS), voltage monitor(VM) & process detector(PD) modules. Add hardware monitoring driver to support MR75203 PVT controller.

Some nit-picks below.

Reviewed-by Andy Shevchenko <[email protected]>

Quoted 7 lines

Signed-off-by Rahul Tanwar <[email protected]>

---
 drivers/hwmon/Kconfig   |  10 +
 drivers/hwmon/Makefile  |   1 +
 drivers/hwmon/mr75203.c | 651 ++++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 662 insertions(+)
 create mode 100644 drivers/hwmon/mr75203.c

Quoted 14 lines

drivers/hwmon/mr75203.c new file +14 -0

+		pvt_temp.config = temp_config;
+
+		pvt_info[index++] = &pvt_temp;
+	}
+
+	if (pd_num) {
+		ret = pvt_get_regmap(pdev, "pd", pvt);
+		if (ret)
+			return ret;
+	}
+
+	if (vm_num) {
+		u32 num = vm_num;
+

drivers/hwmon/mr75203.c line 597

Quoted 10 lines

drivers/hwmon/mr75203.c new file +10 -0

+		ret = pvt_get_regmap(pdev, "vm", pvt);
+		if (ret)
+			return ret;
+
+		pvt->vm_idx = devm_kcalloc(dev, vm_num, sizeof(*pvt->vm_idx),
+					   GFP_KERNEL);
+		if (!pvt->vm_idx)
+			return -ENOMEM;
+		for (i = 0; i < vm_num; i++)
+			pvt->vm_idx[i] = i;

What the point if you are replace them below in one case?

drivers/hwmon/mr75203.c line 601

Quoted 3 lines

drivers/hwmon/mr75203.c new file +3 -0

+		ret = device_property_read_u8_array(dev, "intel,vm-map",
+						    pvt->vm_idx, vm_num);
+		if (!ret)

Misses {} and because of above

	if (ret) {
		for () ...
	} else {
		for () ...
	}

drivers/hwmon/mr75203.c line 607

Quoted 6 lines

drivers/hwmon/mr75203.c new file +6 -0

+			for (i = 0; i < vm_num; i++)
+				if (pvt->vm_idx[i] >= vm_num ||
+				    pvt->vm_idx[i] == 0xff) {
+					num = i;
+					break;
+				}

Or looking in this, perhaps move the incremental for-loop here and start it with num which is 0.

Quoted 1 line · Andy Shevchenko

On Fri, Oct 02, 2020 at 03:04:27PM +0800, Rahul Tanwar wrote:

Quoted 37 lines

Quoted 14 lines

drivers/hwmon/mr75203.c new file +14 -0

+            pvt_temp.config = temp_config;
+
+            pvt_info[index++] = &pvt_temp;
+    }
+
+    if (pd_num) {
+            ret = pvt_get_regmap(pdev, "pd", pvt);
+            if (ret)
+                    return ret;
+    }
+
+    if (vm_num) {
+            u32 num = vm_num;
+

drivers/hwmon/mr75203.c line 597

Quoted 10 lines

drivers/hwmon/mr75203.c new file +10 -0

+            ret = pvt_get_regmap(pdev, "vm", pvt);
+            if (ret)
+                    return ret;
+
+            pvt->vm_idx = devm_kcalloc(dev, vm_num, sizeof(*pvt->vm_idx),
+                                       GFP_KERNEL);
+            if (!pvt->vm_idx)
+                    return -ENOMEM;
+            for (i = 0; i < vm_num; i++)
+                    pvt->vm_idx[i] = i;

What the point if you are replace them below in one case?

drivers/hwmon/mr75203.c line 601

Quoted 3 lines

drivers/hwmon/mr75203.c new file +3 -0

+            ret = device_property_read_u8_array(dev, "intel,vm-map",
+                                                pvt->vm_idx, vm_num);
+            if (!ret)

Misses {} and because of above

      if (ret) {
              for () ...
      } else {
              for () ...
      }

Quoted 8 lines

drivers/hwmon/mr75203.c line 607

Quoted 6 lines

drivers/hwmon/mr75203.c new file +6 -0

+                    for (i = 0; i < vm_num; i++)
+                            if (pvt->vm_idx[i] >= vm_num ||
+                                pvt->vm_idx[i] == 0xff) {
+                                    num = i;
+                                    break;
+                            }

Or looking in this, perhaps move the incremental for-loop here and start it with num which is 0.

Not able to understand what exactly you are suggesting here. Presently it is like below:
1. Init vm_idx array with incremental values.
2. Read array from device property.
3. If success, figure out the last valid value and assign to num.

Can you please elaborate and explain more clearly? Thanks.