Skip to contentSkip to conversation

xilinx: common: Several minor fixups

PATCH New Michal Simek 3 participants 15 messages Oct 22, 2020 – Oct 27, 2020

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

cover xilinx: common: Several minor fixups

Hi,

I am sending some patches to fix minor stuff. There are several things as setting up proper variables, enabling commands.
This series is based on my latest patches I have sent.

Thanks,
Michal

Michal Simek (7):
xilinx: common: Protect board_late_init_xilinx()
xilinx: Enable FRU command for all ARM based platforms
xilinx: zynq: Change types from u32 to uint32_t
xilinx: zynq: Enable AES command
xilinx: Enable SF_TEST command for all ARM based platforms
xilinx: Remove additional newline in config files
xilinx: Merge together BOOT_SCRIPT_OFFSET between MB and ARM

Siva Durga Prasad Paladugu (1):
arm64: versal: Set initrd_high to as high as possible

T Karthik Reddy (2):
arm64: zynqmp: Fix zynqmp mini qspi max frequency
xilinx: Add DDR base address to bootscript address

 arch/arm/dts/zynqmp-mini-qspi.dts       |  2 +-
 arch/microblaze/Kconfig                 |  1 +
 board/xilinx/Kconfig                    |  6 +++---
 board/xilinx/common/board.c             | 11 +++++++++++
 board/xilinx/microblaze-generic/Kconfig |  5 -----
 board/xilinx/versal/board.c             |  4 ++++
 configs/xilinx_versal_virt_defconfig    |  2 ++
 configs/xilinx_zynq_virt_defconfig      |  3 +++
 configs/xilinx_zynqmp_virt_defconfig    |  2 ++
 include/configs/xilinx_versal.h         |  1 -
 include/configs/xilinx_versal_mini.h    |  1 -
 include/configs/xilinx_zynqmp_mini.h    |  1 -
 include/u-boot/rsa-mod-exp.h            |  2 +-
 lib/rsa/rsa-mod-exp.c                   |  2 +-
 14 files changed, 29 insertions(+), 14 deletions(-)
Signature · 1 line
2.28.0
#1 lore raw

PATCH 1/10 arm64: zynqmp: Fix zynqmp mini qspi max frequency

From: T Karthik Reddy <[email protected]>

For zynqmp qspi, frequencies up to 40MHz will work irrespective of feedback clock enabled or disabled. If we want higher than 40Mhz the feedback clock should be enabled.

With spi-max-frequency 108MHz it is not working when the feedback clock is disabled. Change it to 40MHz so that it works irrespective of feedback clock enabled or disabled.

---

 arch/arm/dts/zynqmp-mini-qspi.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/dts/zynqmp-mini-qspi.dts +1 -1
index a76e6404661e..9b4320fe6e20 100644
@@ -70,7 +70,7 @@
 		reg = <0x0>;
 		spi-tx-bus-width = <1>;
 		spi-rx-bus-width = <4>;
-		spi-max-frequency = <108000000>;
+		spi-max-frequency = <40000000>;
 	};
 };
 
Signature · 1 line
2.28.0
#2 lore raw

PATCH 2/10 xilinx: common: Protect board_late_init_xilinx()

In reply to Michal Simek

Do not call board_late_init_xilinx() when BOARD_LATE_INIT is not enabled.

---

 board/xilinx/common/board.c | 2 ++
 1 file changed, 2 insertions(+)
board/xilinx/common/board.c +2 -0
index 74e81c18bd5a..821ee836dd84 100644
@@ -352,6 +352,7 @@ void *board_fdt_blob_setup(void)
 }
 #endif
 
+#if defined(CONFIG_BOARD_LATE_INIT)
 static int env_set_by_index(const char *name, int index, char *data)
 {
 	char var[32];
@@ -414,3 +415,4 @@ int board_late_init_xilinx(void)
 
 	return 0;
 }
+#endif
Signature · 1 line
2.28.0
#3 lore raw

PATCH 3/10 xilinx: Add DDR base address to bootscript address

In reply to Michal Simek

From: T Karthik Reddy <[email protected]>

Add ram base address to scriptaddr env variable to make boot script address to be a valid address when ddr base address changes.

This works properly if the first memory region is the region where uboot runs. Also the solution was taken in respect of a lot of jtag script putting u-boot script to certain address. For standard cases bd->bi_dram[0].start is 0 all the time. Only for systems with DDR placed out of this location it does calculation.

This is not the best solution and should be done differently in future but enough for now till we don't have full solution ready yet.

---

 board/xilinx/common/board.c | 9 +++++++++
 1 file changed, 9 insertions(+)
board/xilinx/common/board.c +9 -0
index 821ee836dd84..857a66a50407 100644
@@ -371,6 +371,15 @@ int board_late_init_xilinx(void)
 	int i, id, macid = 0;
 	struct xilinx_board_description *desc;
 	phys_size_t bootm_size = gd->ram_size;
+	struct bd_info *bd = gd->bd;
+
+	if (bd->bi_dram[0].start) {
+		ulong scriptaddr;
+
+		scriptaddr = env_get_hex("scriptaddr", 0);
+		ret |= env_set_hex("scriptaddr",
+				   bd->bi_dram[0].start + scriptaddr);
+	}
 
 	if (CONFIG_IS_ENABLED(ARCH_ZYNQ))
 		bootm_size = min(bootm_size, (phys_size_t)(SZ_512M + SZ_256M));
Signature · 1 line
2.28.0
#4 lore raw

PATCH 4/10 xilinx: Enable FRU command for all ARM based platforms

In reply to Michal Simek

Enable it by default for board detection.

---

 configs/xilinx_versal_virt_defconfig | 1 +
 configs/xilinx_zynq_virt_defconfig   | 1 +
 configs/xilinx_zynqmp_virt_defconfig | 1 +
 3 files changed, 3 insertions(+)
configs/xilinx_versal_virt_defconfig +1 -0
index b6ca566ed8cd..34ff8ddde0c1 100644
@@ -4,6 +4,7 @@ CONFIG_ARCH_VERSAL=y
 CONFIG_SYS_TEXT_BASE=0x8000000
 CONFIG_SYS_MALLOC_F_LEN=0x100000
 CONFIG_DM_GPIO=y
+CONFIG_CMD_FRU=y
 CONFIG_DEFINE_TCM_OCM_MMAP=y
 CONFIG_COUNTER_FREQUENCY=100000000
 CONFIG_DISTRO_DEFAULTS=y
configs/xilinx_zynq_virt_defconfig +1 -0
index df3da763c500..439a4fe6e539 100644
@@ -6,6 +6,7 @@ CONFIG_SYS_SPI_U_BOOT_OFFS=0x100000
 CONFIG_DM_GPIO=y
 CONFIG_SPL_STACK_R_ADDR=0x200000
 CONFIG_SPL=y
+CONFIG_CMD_FRU=y
 CONFIG_DEFAULT_DEVICE_TREE="zynq-zc706"
 CONFIG_DISTRO_DEFAULTS=y
 CONFIG_SYS_CUSTOM_LDSCRIPT=y
configs/xilinx_zynqmp_virt_defconfig +1 -0
index 01b2f18a057a..8937658a25d5 100644
@@ -9,6 +9,7 @@ CONFIG_SPL_SPI_FLASH_SUPPORT=y
 CONFIG_SPL_SPI_SUPPORT=y
 CONFIG_ZYNQ_MAC_IN_EEPROM=y
 CONFIG_ZYNQ_GEM_I2C_MAC_OFFSET=0x20
+CONFIG_CMD_FRU=y
 CONFIG_ZYNQMP_USB=y
 CONFIG_DEFAULT_DEVICE_TREE="zynqmp-zcu100-revC"
 CONFIG_AHCI=y
Signature · 1 line
2.28.0
#5 lore raw

PATCH 5/10 xilinx: zynq: Change types from u32 to uint32_t

In reply to Michal Simek

Change parameter type to avoid compilation error:
In file included from ./tools/../lib/rsa/rsa-verify.c:23:0,
from tools/lib/rsa/rsa-verify.c:1:
include/u-boot/rsa-mod-exp.h:69:18: error: unknown type name ?u32?; did you mean ?__u32??

 int zynq_pow_mod(u32 *keyptr, u32 *inout);
                  ^~~
                  __u32
include/u-boot/rsa-mod-exp.h:69:31: error: unknown type name ?u32?; did you mean ?__u32??
 int zynq_pow_mod(u32 *keyptr, u32 *inout);
                               ^~~
                               __u32
Fixes 37e3a36a5475 ("xilinx: zynq: Add support to secure images")

---

 include/u-boot/rsa-mod-exp.h | 2 +-
 lib/rsa/rsa-mod-exp.c        | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)
include/u-boot/rsa-mod-exp.h +1 -1
index 1da8af1bb83d..7b7c2915a94b 100644
@@ -66,7 +66,7 @@ int rsa_mod_exp(struct udevice *dev, const uint8_t *sig, uint32_t sig_len,
 		struct key_prop *node, uint8_t *out);
 
 #if defined(CONFIG_CMD_ZYNQ_RSA)
-int zynq_pow_mod(u32 *keyptr, u32 *inout);
+int zynq_pow_mod(uint32_t *keyptr, uint32_t *inout);
 #endif
 
 /**
lib/rsa/rsa-mod-exp.c +1 -1
index 78c688d14c33..74f9eb16cc26 100644
@@ -321,7 +321,7 @@ int rsa_mod_exp_sw(const uint8_t *sig, uint32_t sig_len,
  *        pow_mod calculation required for zynq is bit different from
  *        pw_mod above here, hence defined zynq specific routine.
  */
-int zynq_pow_mod(u32 *keyptr, u32 *inout)
+int zynq_pow_mod(uint32_t *keyptr, uint32_t *inout)
 {
 	u32 *result, *ptr;
 	uint i;
Signature · 1 line
2.28.0
#6 lore raw

PATCH 6/10 xilinx: zynq: Enable AES command

In reply to Michal Simek

Enable AES command to be able to use it directly.

---

 configs/xilinx_zynq_virt_defconfig | 1 +
 1 file changed, 1 insertion(+)
configs/xilinx_zynq_virt_defconfig +1 -0
index 439a4fe6e539..09820d76a61a 100644
@@ -7,6 +7,7 @@ CONFIG_DM_GPIO=y
 CONFIG_SPL_STACK_R_ADDR=0x200000
 CONFIG_SPL=y
 CONFIG_CMD_FRU=y
+CONFIG_CMD_ZYNQ_AES=y
 CONFIG_DEFAULT_DEVICE_TREE="zynq-zc706"
 CONFIG_DISTRO_DEFAULTS=y
 CONFIG_SYS_CUSTOM_LDSCRIPT=y
Signature · 1 line
2.28.0
#7 lore raw

PATCH 7/10 xilinx: Enable SF_TEST command for all ARM based platforms

In reply to Michal Simek

Enable this command by default.

---

 configs/xilinx_versal_virt_defconfig | 1 +
 configs/xilinx_zynq_virt_defconfig   | 1 +
 configs/xilinx_zynqmp_virt_defconfig | 1 +
 3 files changed, 3 insertions(+)
configs/xilinx_versal_virt_defconfig +1 -0
index 34ff8ddde0c1..40a8cfd5ccc7 100644
@@ -28,6 +28,7 @@ CONFIG_CMD_GPIO=y
 CONFIG_CMD_I2C=y
 CONFIG_CMD_MMC=y
 CONFIG_CMD_MTD=y
+CONFIG_CMD_SF_TEST=y
 CONFIG_CMD_USB=y
 CONFIG_CMD_TFTPPUT=y
 CONFIG_CMD_CACHE=y
configs/xilinx_zynq_virt_defconfig +1 -0
index 09820d76a61a..da84c01b0a1a 100644
@@ -42,6 +42,7 @@ CONFIG_CMD_I2C=y
 CONFIG_CMD_MMC=y
 CONFIG_CMD_MTD=y
 CONFIG_CMD_NAND_LOCK_UNLOCK=y
+CONFIG_CMD_SF_TEST=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_TFTPPUT=y
configs/xilinx_zynqmp_virt_defconfig +1 -0
index 8937658a25d5..0c816de707ac 100644
@@ -49,6 +49,7 @@ CONFIG_CMD_MTD=y
 CONFIG_CMD_NAND_LOCK_UNLOCK=y
 CONFIG_CMD_POWEROFF=y
 CONFIG_CMD_SDRAM=y
+CONFIG_CMD_SF_TEST=y
 CONFIG_CMD_SPI=y
 CONFIG_CMD_USB=y
 CONFIG_CMD_USB_MASS_STORAGE=y
Signature · 1 line
2.28.0
#8 lore raw

PATCH 8/10 xilinx: Remove additional newline in config files

In reply to Michal Simek

Trivial fix.

Fixes e519f03a1846 ("cmd: mem: Remove CONFIG_SYS_MEMTEST_SCRATCH mapping")

---

 include/configs/xilinx_versal.h      | 1 -
 include/configs/xilinx_versal_mini.h | 1 -
 include/configs/xilinx_zynqmp_mini.h | 1 -
 3 files changed, 3 deletions(-)
include/configs/xilinx_versal.h +0 -1
index 8b416327b57c..f1d2594f3b32 100644
@@ -18,7 +18,6 @@
 #define GICD_BASE	0xF9000000
 #define GICR_BASE	0xF9080000
 
-
 #define CONFIG_SYS_INIT_SP_ADDR		CONFIG_SYS_TEXT_BASE
 
 /* Generic Timer Definitions - setup in EL3. Setup by ATF for other cases */
include/configs/xilinx_versal_mini.h +0 -1
index 0b201a2b4d69..00c971881985 100644
@@ -10,7 +10,6 @@
 #ifndef __CONFIG_VERSAL_MINI_H
 #define __CONFIG_VERSAL_MINI_H
 
-
 #define CONFIG_EXTRA_ENV_SETTINGS
 
 #include <configs/xilinx_versal.h>
include/configs/xilinx_zynqmp_mini.h +0 -1
index 3f57423b7898..ef9c768e48eb 100644
@@ -10,7 +10,6 @@
 #ifndef __CONFIG_ZYNQMP_MINI_H
 #define __CONFIG_ZYNQMP_MINI_H
 
-
 #define CONFIG_EXTRA_ENV_SETTINGS
 
 #include <configs/xilinx_zynqmp.h>
Signature · 1 line
2.28.0
#9 lore raw

PATCH 9/10 xilinx: Merge together BOOT_SCRIPT_OFFSET between MB and ARM

In reply to Michal Simek

There is no reason not to use commong Kconfig by Microblaze too.

---

 arch/microblaze/Kconfig                 | 1 +
 board/xilinx/Kconfig                    | 6 +++---
 board/xilinx/microblaze-generic/Kconfig | 5 -----
 3 files changed, 4 insertions(+), 8 deletions(-)
arch/microblaze/Kconfig +1 -0
index 2755cce884c5..99a17bccb388 100644
@@ -23,6 +23,7 @@ config TARGET_MICROBLAZE_GENERIC
 
 endchoice
 
+source "board/xilinx/Kconfig"
 source "board/xilinx/microblaze-generic/Kconfig"
 
 endmenu
board/xilinx/Kconfig +3 -3
index 51f6d2bac8ad..64507b5d8438 100644
@@ -50,12 +50,12 @@ config XILINX_OF_BOARD_DTB_ADDR
 
 config BOOT_SCRIPT_OFFSET
 	hex "Boot script offset"
-	depends on ARCH_ZYNQ || ARCH_ZYNQMP || ARCH_VERSAL
-	default 0xFC0000 if ARCH_ZYNQ
+	depends on ARCH_ZYNQ || ARCH_ZYNQMP || ARCH_VERSAL || MICROBLAZE
+	default 0xFC0000 if ARCH_ZYNQ || MICROBLAZE
 	default 0x3E80000 if ARCH_ZYNQMP
 	default 0x7F80000 if ARCH_VERSAL
 	help
-	   Specifies distro boot script offset in NAND/NOR flash.
+	   Specifies distro boot script offset in NAND/QSPI/NOR flash.
 
 config ZYNQ_MAC_IN_EEPROM
 	bool "Reading MAC address from EEPROM"
board/xilinx/microblaze-generic/Kconfig +0 -5
index 7a97211a1ecd..f2fa0f72b13f 100644
@@ -38,9 +38,4 @@ config XILINX_MICROBLAZE0_HW_VER
 	string "Core version number"
 	default "7.10.d"
 
-config BOOT_SCRIPT_OFFSET
-        hex "Boot script offset"
-        default 0xFC0000
-        help
-           Specifies distro boot script offset in NAND/QSPI flash.
 endif
Signature · 1 line
2.28.0
#10 lore raw

PATCH 10/10 arm64: versal: Set initrd_high to as high as possible

In reply to Michal Simek

From: Siva Durga Prasad Paladugu <[email protected]>

This patch is setting up the initrd_high to as high as possible by leaving max stack size for u-boot so that bigger rootfs can also be loaded by u-boot for booting kernel.

---

 board/xilinx/versal/board.c | 4 ++++
 1 file changed, 4 insertions(+)
board/xilinx/versal/board.c +4 -0
index 912c1143a8ad..09229e0a75a4 100644
@@ -217,6 +217,10 @@ int board_late_init(void)
 
 	env_set("boot_targets", new_targets);
 
+	initrd_hi = gd->start_addr_sp - CONFIG_STACK_SIZE;
+	initrd_hi = round_down(initrd_hi, SZ_16M);
+	env_set_addr("initrd_high", (void *)initrd_hi);
+
 	return board_late_init_xilinx();
 }
 
Signature · 1 line
2.28.0
#11 lore raw

PATCH 10/10 arm64: versal: Set initrd_high to as high as possible

Quoted 18 lines · Michal Simek

From: Siva Durga Prasad Paladugu <[email protected]>

This patch is setting up the initrd_high to as high as possible by leaving max stack size for u-boot so that bigger rootfs can also be loaded by u-boot for booting kernel.

---

 board/xilinx/versal/board.c | 4 ++++
 1 file changed, 4 insertions(+)
board/xilinx/versal/board.c +0 -0
index 912c1143a8ad..09229e0a75a4 100644

board/xilinx/versal/board.c int board_late_init(void) · line 225

Quoted 9 lines
board/xilinx/versal/board.c +4 -0
@@ -217,6 +217,10 @@ int board_late_init(void)
 
 	env_set("boot_targets", new_targets);
 
+	initrd_hi = gd->start_addr_sp - CONFIG_STACK_SIZE;
+	initrd_hi = round_down(initrd_hi, SZ_16M);
+	env_set_addr("initrd_high", (void *)initrd_hi);
+
 	return board_late_init_xilinx();
 }

My concern here (and also microblaze-generic, after some grepping) is that wouldn't it be best to set bootm_size and let fdt and initrd be relocated as needed?

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 659 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20201022/85822e0d/attachment.sig>
#12 lore raw

PATCH 10/10 arm64: versal: Set initrd_high to as high as possible

Quoted 24 lines · Tom Rini
Quoted 22 lines · Michal Simek

From: Siva Durga Prasad Paladugu
<[email protected]>

This patch is setting up the initrd_high to as high as possible by leaving max stack size for u-boot so that bigger rootfs can also be loaded by u-boot for booting kernel.

Signed-off-by: Siva Durga Prasad Paladugu <[email protected]> Signed-off-by: Michal Simek <[email protected]> ---

board/xilinx/versal/board.c | 4 ++++ 1 file changed, 4 insertions(+)

(quoted diff) +0 -0

b/board/xilinx/versal/board.c index 912c1143a8ad..09229e0a75a4 100644 --- a/board/xilinx/versal/board.c +++ b/board/xilinx/versal/board.c @@ -217,6 +217,10 @@ int board_late_init(void)

env_set("boot_targets", new_targets);

Quoted 7 lines
Quoted 3 lines
(quoted diff) +1 -0
+	initrd_hi = gd->start_addr_sp - CONFIG_STACK_SIZE; +	initrd_hi

= round_down(initrd_hi, SZ_16M); + env_set_addr("initrd_high",
(void *)initrd_hi); + return board_late_init_xilinx(); }

My concern here (and also microblaze-generic, after some grepping) is that wouldn't it be best to set bootm_size and let fdt and initrd be relocated as needed?

You are right and I have already done it in this way but forget to remove this patch from my queue. Will drop this patch.

Thanks,
Michal

maintainer Applied
#14 lore raw

cover xilinx: common: Several minor fixups

In reply to Michal Simek

?t 22. 10. 2020 v 12:32 odes?latel Michal Simek
<[email protected]> napsal:

Quoted 43 lines

Hi,

I am sending some patches to fix minor stuff. There are several things as setting up proper variables, enabling commands.
This series is based on my latest patches I have sent.

Thanks,
Michal

Michal Simek (7):
xilinx: common: Protect board_late_init_xilinx()
xilinx: Enable FRU command for all ARM based platforms
xilinx: zynq: Change types from u32 to uint32_t
xilinx: zynq: Enable AES command
xilinx: Enable SF_TEST command for all ARM based platforms
xilinx: Remove additional newline in config files
xilinx: Merge together BOOT_SCRIPT_OFFSET between MB and ARM

Siva Durga Prasad Paladugu (1):
arm64: versal: Set initrd_high to as high as possible

T Karthik Reddy (2):
arm64: zynqmp: Fix zynqmp mini qspi max frequency
xilinx: Add DDR base address to bootscript address

 arch/arm/dts/zynqmp-mini-qspi.dts       |  2 +-
 arch/microblaze/Kconfig                 |  1 +
 board/xilinx/Kconfig                    |  6 +++---
 board/xilinx/common/board.c             | 11 +++++++++++
 board/xilinx/microblaze-generic/Kconfig |  5 -----
 board/xilinx/versal/board.c             |  4 ++++
 configs/xilinx_versal_virt_defconfig    |  2 ++
 configs/xilinx_zynq_virt_defconfig      |  3 +++
 configs/xilinx_zynqmp_virt_defconfig    |  2 ++
 include/configs/xilinx_versal.h         |  1 -
 include/configs/xilinx_versal_mini.h    |  1 -
 include/configs/xilinx_zynqmp_mini.h    |  1 -
 include/u-boot/rsa-mod-exp.h            |  2 +-
 lib/rsa/rsa-mod-exp.c                   |  2 +-
 14 files changed, 29 insertions(+), 14 deletions(-)
Quoted 3 lines

--
2.28.0

Applied.
M

Signature · 5 lines
Michal Simek, Ing. (M.Eng), OpenPGP -> KeyID: FE3D1F91
w: www.monstr.eu p: +42-0-721842854
Maintainer of Linux kernel - Xilinx Microblaze
Maintainer of Linux kernel - Xilinx Zynq ARM and ZynqMP ARM64 SoCs
U-Boot custodian - Xilinx Microblaze/Zynq/ZynqMP/Versal SoCs
maintainer
#13 lore raw

PATCH 10/10 arm64: versal: Set initrd_high to as high as possible

In reply to Michal Simek

p? 23. 10. 2020 v 7:44 odes?latel Michal Simek <[email protected]> napsal:

Quoted 36 lines · Tom Rini
Quoted 24 lines · Michal Simek
Quoted 23 lines

From: Siva Durga Prasad Paladugu
<[email protected]>

This patch is setting up the initrd_high to as high as possible by leaving max stack size for u-boot so that bigger rootfs can also be loaded by u-boot for booting kernel.

Signed-off-by: Siva Durga Prasad Paladugu <[email protected]> Signed-off-by: Michal Simek <[email protected]> ---

board/xilinx/versal/board.c | 4 ++++ 1 file changed, 4 insertions(+)

(quoted diff) +0 -0

b/board/xilinx/versal/board.c index 912c1143a8ad..09229e0a75a4 100644 --- a/board/xilinx/versal/board.c +++ b/board/xilinx/versal/board.c @@ -217,6 +217,10 @@ int board_late_init(void)

env_set("boot_targets", new_targets);

Quoted 7 lines
Quoted 3 lines

+ initrd_hi = gd->start_addr_sp - CONFIG_STACK_SIZE; + initrd_hi
= round_down(initrd_hi, SZ_16M); + env_set_addr("initrd_high",
(void *)initrd_hi); + return board_late_init_xilinx(); }

My concern here (and also microblaze-generic, after some grepping) is that wouldn't it be best to set bootm_size and let fdt and initrd be relocated as needed?

Quoted 5 lines

You are right and I have already done it in this way but forget to remove this patch from my queue. Will drop this patch.

Thanks,
Michal

This patch has been dropped from the series.
1-9 applied.
M

Signature · 5 lines
Michal Simek, Ing. (M.Eng), OpenPGP -> KeyID: FE3D1F91
w: www.monstr.eu p: +42-0-721842854
Maintainer of Linux kernel - Xilinx Microblaze
Maintainer of Linux kernel - Xilinx Zynq ARM and ZynqMP ARM64 SoCs
U-Boot custodian - Xilinx Microblaze/Zynq/ZynqMP/Versal SoCs